From: Eliad Peller <eliad@wizery.com>
To: Luciano Coelho <luca@coelho.fi>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH 01/13] wl18xx: default config alignment with phy defaults
Date: Mon, 9 Sep 2013 12:24:32 +0300 [thread overview]
Message-ID: <1378718684-14430-1-git-send-email-eliad@wizery.com> (raw)
From: Igal Chernobelsky <igalc@ti.com>
Driver default config is aligned with phy default parameters.
Now that RDL1_3 has 2 antennas defined by default we need to explicitly
define ht.mode to HT_MODE_WIDE to have SISO40 as default.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
---
drivers/net/wireless/ti/wl18xx/main.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index aef0c91..7302308 100644
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -505,7 +505,7 @@ static struct wlcore_conf wl18xx_conf = {
static struct wl18xx_priv_conf wl18xx_default_priv_conf = {
.ht = {
- .mode = HT_MODE_DEFAULT,
+ .mode = HT_MODE_WIDE,
},
.phy = {
.phy_standalone = 0x00,
@@ -516,7 +516,7 @@ static struct wl18xx_priv_conf wl18xx_default_priv_conf = {
.auto_detect = 0x00,
.dedicated_fem = FEM_NONE,
.low_band_component = COMPONENT_3_WAY_SWITCH,
- .low_band_component_type = 0x04,
+ .low_band_component_type = 0x05,
.high_band_component = COMPONENT_2_WAY_SWITCH,
.high_band_component_type = 0x09,
.tcxo_ldo_voltage = 0x00,
@@ -556,15 +556,15 @@ static struct wl18xx_priv_conf wl18xx_default_priv_conf = {
.per_chan_pwr_limit_arr_11p = { 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff },
.psat = 0,
- .low_power_val = 0x08,
- .med_power_val = 0x12,
- .high_power_val = 0x18,
- .low_power_val_2nd = 0x05,
- .med_power_val_2nd = 0x0a,
- .high_power_val_2nd = 0x14,
.external_pa_dc2dc = 0,
.number_of_assembled_ant2_4 = 2,
.number_of_assembled_ant5 = 1,
+ .low_power_val = 0xff,
+ .med_power_val = 0xff,
+ .high_power_val = 0xff,
+ .low_power_val_2nd = 0xff,
+ .med_power_val_2nd = 0xff,
+ .high_power_val_2nd = 0xff,
.tx_rf_margin = 1,
},
};
--
1.8.3.rc1.35.g9b79519
next reply other threads:[~2013-09-09 9:24 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-09-09 9:24 Eliad Peller [this message]
2013-09-09 9:24 ` [PATCH 02/13] wlcore: print active channel in the driver_state Eliad Peller
2013-09-09 9:24 ` [PATCH 03/13] wlcore: add ap_event_mask Eliad Peller
2013-09-09 9:24 ` [PATCH 04/13] wlcore: fix interrogate command length Eliad Peller
2013-09-09 9:24 ` [PATCH 05/13] wlcore: fwlog dynamic mem_block control Eliad Peller
2013-09-09 9:24 ` [PATCH 06/13] wl12xx/wl18xx: update default fw logger's settings Eliad Peller
2013-09-09 9:24 ` [PATCH 07/13] wlcore/wl18xx/wl12xx: FW log params per chip arch Eliad Peller
2013-09-09 9:24 ` [PATCH 08/13] wlcore: read fw panic log only in host mode Eliad Peller
2013-09-09 9:24 ` [PATCH 09/13] wlcore: Allow stopping fw log in recovery Eliad Peller
2013-09-09 9:24 ` [PATCH 10/13] wlcore: wakeup from ELP before starting recovery Eliad Peller
2013-09-09 9:24 ` [PATCH 11/13] wlcore: memset wl->rx_filter_enabled to zero after recovery Eliad Peller
2013-10-23 5:23 ` Luca Coelho
2013-10-23 7:37 ` Eliad Peller
2013-09-09 9:24 ` [PATCH 12/13] wlcore: fix started_vifs calculation Eliad Peller
2013-09-09 9:24 ` [PATCH 13/13] wlcore: save last regdom configuration on stop Eliad Peller
2013-10-23 7:07 ` [PATCH 01/13] wl18xx: default config alignment with phy defaults Luca Coelho
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1378718684-14430-1-git-send-email-eliad@wizery.com \
--to=eliad@wizery.com \
--cc=linux-wireless@vger.kernel.org \
--cc=luca@coelho.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox