From: Eliad Peller <eliad@wizery.com>
To: Luciano Coelho <luca@coelho.fi>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH 06/13] wl12xx/wl18xx: update default fw logger's settings
Date: Mon, 9 Sep 2013 12:24:37 +0300 [thread overview]
Message-ID: <1378718684-14430-6-git-send-email-eliad@wizery.com> (raw)
In-Reply-To: <1378718684-14430-1-git-send-email-eliad@wizery.com>
From: Ido Reis <idor@ti.com>
update the fw logger mode to continuous, and output to dbgpins (uart).
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
---
drivers/net/wireless/ti/wl12xx/main.c | 4 ++--
drivers/net/wireless/ti/wl18xx/main.c | 4 ++--
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index f147e32..d94173c 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -333,11 +333,11 @@ static struct wlcore_conf wl12xx_conf = {
.always = 0,
},
.fwlog = {
- .mode = WL12XX_FWLOG_ON_DEMAND,
+ .mode = WL12XX_FWLOG_CONTINUOUS,
.mem_blocks = 2,
.severity = 0,
.timestamp = WL12XX_FWLOG_TIMESTAMP_DISABLED,
- .output = WL12XX_FWLOG_OUTPUT_HOST,
+ .output = WL12XX_FWLOG_OUTPUT_DBG_PINS,
.threshold = 0,
},
.rate = {
diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index a02e0bf..aaea0cc 100644
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -456,11 +456,11 @@ static struct wlcore_conf wl18xx_conf = {
.always = 0,
},
.fwlog = {
- .mode = WL12XX_FWLOG_ON_DEMAND,
+ .mode = WL12XX_FWLOG_CONTINUOUS,
.mem_blocks = 2,
.severity = 0,
.timestamp = WL12XX_FWLOG_TIMESTAMP_DISABLED,
- .output = WL12XX_FWLOG_OUTPUT_HOST,
+ .output = WL12XX_FWLOG_OUTPUT_DBG_PINS,
.threshold = 0,
},
.rate = {
--
1.8.3.rc1.35.g9b79519
next prev parent reply other threads:[~2013-09-09 9:25 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-09-09 9:24 [PATCH 01/13] wl18xx: default config alignment with phy defaults Eliad Peller
2013-09-09 9:24 ` [PATCH 02/13] wlcore: print active channel in the driver_state Eliad Peller
2013-09-09 9:24 ` [PATCH 03/13] wlcore: add ap_event_mask Eliad Peller
2013-09-09 9:24 ` [PATCH 04/13] wlcore: fix interrogate command length Eliad Peller
2013-09-09 9:24 ` [PATCH 05/13] wlcore: fwlog dynamic mem_block control Eliad Peller
2013-09-09 9:24 ` Eliad Peller [this message]
2013-09-09 9:24 ` [PATCH 07/13] wlcore/wl18xx/wl12xx: FW log params per chip arch Eliad Peller
2013-09-09 9:24 ` [PATCH 08/13] wlcore: read fw panic log only in host mode Eliad Peller
2013-09-09 9:24 ` [PATCH 09/13] wlcore: Allow stopping fw log in recovery Eliad Peller
2013-09-09 9:24 ` [PATCH 10/13] wlcore: wakeup from ELP before starting recovery Eliad Peller
2013-09-09 9:24 ` [PATCH 11/13] wlcore: memset wl->rx_filter_enabled to zero after recovery Eliad Peller
2013-10-23 5:23 ` Luca Coelho
2013-10-23 7:37 ` Eliad Peller
2013-09-09 9:24 ` [PATCH 12/13] wlcore: fix started_vifs calculation Eliad Peller
2013-09-09 9:24 ` [PATCH 13/13] wlcore: save last regdom configuration on stop Eliad Peller
2013-10-23 7:07 ` [PATCH 01/13] wl18xx: default config alignment with phy defaults Luca Coelho
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1378718684-14430-6-git-send-email-eliad@wizery.com \
--to=eliad@wizery.com \
--cc=linux-wireless@vger.kernel.org \
--cc=luca@coelho.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox