From: Larry Finger <Larry.Finger@lwfinger.net>
To: kvalo@codeaurora.org
Cc: devel@driverdev.osuosl.org, linux-wireless@vger.kernel.org,
Larry Finger <Larry.Finger@lwfinger.net>,
Ping-Ke Shih <pkshih@realtek.com>
Subject: [PATCH 10/14] rtlwifi_new: rtl8192cu: Remove all instances of DBG_EMERG
Date: Sat, 10 Dec 2016 23:45:15 -0600 [thread overview]
Message-ID: <20161211054523.7119-19-Larry.Finger@lwfinger.net> (raw)
In-Reply-To: <20161211054523.7119-1-Larry.Finger@lwfinger.net>
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
---
.../net/wireless/realtek/rtlwifi/rtl8192cu/hw.c | 33 ++++++++--------------
.../net/wireless/realtek/rtlwifi/rtl8192cu/led.c | 6 ++--
.../net/wireless/realtek/rtlwifi/rtl8192cu/mac.c | 12 +++-----
.../net/wireless/realtek/rtlwifi/rtl8192cu/phy.c | 12 +++-----
.../net/wireless/realtek/rtlwifi/rtl8192cu/rf.c | 3 +-
.../net/wireless/realtek/rtlwifi/rtl8192cu/sw.c | 5 ++--
6 files changed, 24 insertions(+), 47 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c
index ddfcf994..9db6ec6 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c
@@ -452,8 +452,7 @@ static int _rtl92cu_init_power_on(struct ieee80211_hw *hw)
break;
}
if (pollingCount++ > 100) {
- RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG,
- "Failed to polling REG_APS_FSMCO[PFM_ALDN] done!\n");
+ pr_err("Failed to polling REG_APS_FSMCO[PFM_ALDN] done!\n");
return -ENODEV;
}
} while (true);
@@ -486,8 +485,7 @@ static int _rtl92cu_init_power_on(struct ieee80211_hw *hw)
break;
}
if (pollingCount++ > 1000) {
- RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG,
- "Failed to polling REG_APS_FSMCO[APFM_ONMAC] done!\n");
+ pr_err("Failed to polling REG_APS_FSMCO[APFM_ONMAC] done!\n");
return -ENODEV;
}
} while (true);
@@ -687,7 +685,6 @@ static void _rtl92cu_init_chipN_three_out_ep_priority(struct ieee80211_hw *hw,
u8 queue_sel)
{
u16 beQ, bkQ, viQ, voQ, mgtQ, hiQ;
- struct rtl_priv *rtlpriv = rtl_priv(hw);
if (!wmm_enable) { /* typical setting */
beQ = QUEUE_LOW;
@@ -705,8 +702,7 @@ static void _rtl92cu_init_chipN_three_out_ep_priority(struct ieee80211_hw *hw,
hiQ = QUEUE_HIGH;
}
_rtl92c_init_chipN_reg_priority(hw, beQ, bkQ, viQ, voQ, mgtQ, hiQ);
- RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG, "Tx queue select :0x%02x..\n",
- queue_sel);
+ pr_info("Tx queue select :0x%02x..\n", queue_sel);
}
static void _rtl92cu_init_chipN_queue_priority(struct ieee80211_hw *hw,
@@ -765,8 +761,7 @@ static void _rtl92cu_init_chipT_queue_priority(struct ieee80211_hw *hw,
break;
}
rtl_write_byte(rtlpriv, (REG_TRXDMA_CTRL+1), hq_sele);
- RT_TRACE(rtlpriv, COMP_INIT, DBG_EMERG, "Tx queue select :0x%02x..\n",
- hq_sele);
+ pr_info("Tx queue select :0x%02x..\n", hq_sele);
}
static void _rtl92cu_init_queue_priority(struct ieee80211_hw *hw,
@@ -848,8 +843,7 @@ static int _rtl92cu_init_mac(struct ieee80211_hw *hw)
err = _rtl92cu_init_power_on(hw);
if (err) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "Failed to init power on!\n");
+ pr_err("Failed to init power on!\n");
return err;
}
if (!wmm_enable) {
@@ -860,8 +854,7 @@ static int _rtl92cu_init_mac(struct ieee80211_hw *hw)
: WMM_CHIP_A_TX_PAGE_BOUNDARY;
}
if (false == rtl92c_init_llt_table(hw, boundary)) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "Failed to init LLT Table!\n");
+ pr_err("Failed to init LLT Table!\n");
return -EINVAL;
}
_rtl92cu_init_queue_reserved_page(hw, wmm_enable, out_ep_nums,
@@ -986,7 +979,7 @@ int rtl92cu_hw_init(struct ieee80211_hw *hw)
rtlhal->hw_type = HARDWARE_TYPE_RTL8192CU;
err = _rtl92cu_init_mac(hw);
if (err) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG, "init mac failed!\n");
+ pr_err("init mac failed!\n");
goto exit;
}
err = rtl92c_download_fw(hw);
@@ -1099,8 +1092,7 @@ static void _ResetDigitalProcedure1(struct ieee80211_hw *hw, bool bWithoutHWSM)
udelay(50);
}
if (retry_cnts >= 100) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "#####=> 8051 reset failed!.........................\n");
+ pr_err("8051 reset failed!.........................\n");
/* if 8051 reset fail, reset MAC. */
rtl_write_byte(rtlpriv,
REG_SYS_FUNC_EN + 1,
@@ -1340,8 +1332,7 @@ static int _rtl92cu_set_media_status(struct ieee80211_hw *hw,
"Set Network type to AP!\n");
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "Network type %d not supported!\n", type);
+ pr_err("Network type %d not supported!\n", type);
goto error_out;
}
rtl_write_byte(rtlpriv, MSR, bt_msr);
@@ -1555,8 +1546,7 @@ void rtl92cu_get_hw_reg(struct ieee80211_hw *hw, u8 variable, u8 *val)
case HAL_DEF_WOWLAN:
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", variable);
+ pr_err("switch case %#x not processed\n", variable);
break;
}
}
@@ -1926,8 +1916,7 @@ void rtl92cu_set_hw_reg(struct ieee80211_hw *hw, u8 variable, u8 *val)
break;
}
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", variable);
+ pr_err("switch case %#x not processed\n", variable);
break;
}
}
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/led.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/led.c
index c624081..9d83f08 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/led.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/led.c
@@ -57,8 +57,7 @@ void rtl92cu_sw_led_on(struct ieee80211_hw *hw, struct rtl_led *pled)
rtl_write_byte(rtlpriv, REG_LEDCFG2, (ledcfg & 0x0f) | BIT(5));
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", pled->ledpin);
+ pr_err("switch case %#x not processed\n", pled->ledpin);
break;
}
pled->ledon = true;
@@ -90,8 +89,7 @@ void rtl92cu_sw_led_off(struct ieee80211_hw *hw, struct rtl_led *pled)
rtl_write_byte(rtlpriv, REG_LEDCFG2, (ledcfg | BIT(3)));
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", pled->ledpin);
+ pr_err("switch case %#x not processed\n", pled->ledpin);
break;
}
pled->ledon = false;
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c
index cf212f6..1b124ea 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c
@@ -157,9 +157,8 @@ bool rtl92c_llt_write(struct ieee80211_hw *hw, u32 address, u32 data)
if (_LLT_NO_ACTIVE == _LLT_OP_VALUE(value))
break;
if (count > POLLING_LLT_THRESHOLD) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "Failed to polling write LLT done at address %d! _LLT_OP_VALUE(%x)\n",
- address, _LLT_OP_VALUE(value));
+ pr_err("Failed to polling write LLT done at address %d! _LLT_OP_VALUE(%x)\n",
+ address, _LLT_OP_VALUE(value));
status = false;
break;
}
@@ -262,8 +261,7 @@ void rtl92c_set_key(struct ieee80211_hw *hw, u32 key_index,
enc_algo = CAM_AES;
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "illegal switch case\n");
+ pr_err("illegal switch case\n");
enc_algo = CAM_TKIP;
break;
}
@@ -280,9 +278,7 @@ void rtl92c_set_key(struct ieee80211_hw *hw, u32 key_index,
entry_id = rtl_cam_get_free_entry(hw,
p_macaddr);
if (entry_id >= TOTAL_CAM_ENTRY) {
- RT_TRACE(rtlpriv, COMP_SEC,
- DBG_EMERG,
- "Can not find free hw security cam entry\n");
+ pr_err("Can not find free hw security cam entry\n");
return;
}
} else {
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c
index f35f435..452437f 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/phy.c
@@ -274,8 +274,7 @@ bool rtl92cu_phy_config_rf_with_headerfile(struct ieee80211_hw *hw,
break;
case RF90_PATH_C:
case RF90_PATH_D:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", rfpath);
+ pr_err("switch case %#x not processed\n", rfpath);
break;
default:
break;
@@ -314,8 +313,7 @@ void rtl92cu_phy_set_bw_mode_callback(struct ieee80211_hw *hw)
rtl_write_byte(rtlpriv, REG_RRSR + 2, reg_prsr_rsc);
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "unknown bandwidth: %#X\n", rtlphy->current_chan_bw);
+ pr_err("unknown bandwidth: %#X\n", rtlphy->current_chan_bw);
break;
}
switch (rtlphy->current_chan_bw) {
@@ -336,8 +334,7 @@ void rtl92cu_phy_set_bw_mode_callback(struct ieee80211_hw *hw)
HAL_PRIME_CHNL_OFFSET_LOWER) ? 2 : 1);
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "unknown bandwidth: %#X\n", rtlphy->current_chan_bw);
+ pr_err("unknown bandwidth: %#X\n", rtlphy->current_chan_bw);
break;
}
rtl92cu_phy_rf6052_set_bandwidth(hw, rtlphy->current_chan_bw);
@@ -509,8 +506,7 @@ static bool _rtl92cu_phy_set_rf_power_state(struct ieee80211_hw *hw,
_rtl92c_phy_set_rf_sleep(hw);
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "switch case %#x not processed\n", rfpwr_state);
+ pr_err("switch case %#x not processed\n", rfpwr_state);
bresult = false;
break;
}
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c
index 5e31830..9cff6bc 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c
@@ -51,8 +51,7 @@ void rtl92cu_phy_rf6052_set_bandwidth(struct ieee80211_hw *hw, u8 bandwidth)
rtlphy->rfreg_chnlval[0]);
break;
default:
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "unknown bandwidth: %#X\n", bandwidth);
+ pr_err("unknown bandwidth: %#X\n", bandwidth);
break;
}
}
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/sw.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/sw.c
index b84e13a..935e830 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/sw.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192cu/sw.c
@@ -68,8 +68,7 @@ static int rtl92cu_init_sw_vars(struct ieee80211_hw *hw)
/* for firmware buf */
rtlpriv->rtlhal.pfirmware = vzalloc(0x4000);
if (!rtlpriv->rtlhal.pfirmware) {
- RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG,
- "Can't alloc buffer for fw\n");
+ pr_err("Can't alloc buffer for fw\n");
return 1;
}
if (IS_VENDOR_UMC_A_CUT(rtlpriv->rtlhal.version) &&
@@ -158,7 +157,7 @@ static struct rtl_hal_ops rtl8192cu_hal_ops = {
static struct rtl_mod_params rtl92cu_mod_params = {
.sw_crypto = 0,
- .debug = DBG_EMERG,
+ .debug = 0,
};
module_param_named(swenc, rtl92cu_mod_params.sw_crypto, bool, 0444);
--
2.10.2
next prev parent reply other threads:[~2016-12-11 5:45 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-11 5:44 [PATCH 00/14] rtlwifi: Start reworking of debug system Larry Finger
2016-12-11 5:44 ` [PATCH 01/14] rtlwifi: Replace local debug macro RT_ASSERT Larry Finger
2016-12-11 5:44 ` [PATCH 02/14] rtlwifi_new: Remove RT_TRACE messages that use DBG_EMERG Larry Finger
2016-12-11 10:50 ` Joe Perches
2016-12-11 15:31 ` Larry Finger
2016-12-11 5:45 ` [PATCH 02/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 03/14] rtlwifi_new: rtl8821ae: Remove all instances of DBG_EMERG Larry Finger
2016-12-11 5:45 ` [PATCH 03/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 04/14] rtlwifi_new: rtl8723be: " Larry Finger
2016-12-11 5:45 ` [PATCH 04/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 05/14] rtlwifi_new: rtl8723ae: " Larry Finger
2016-12-11 5:45 ` [PATCH 05/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 06/14] rtlwifi_new: rtl8192ee: " Larry Finger
2016-12-11 5:45 ` [PATCH 06/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 07/14] rtlwifi_new: rtl8723-common: " Larry Finger
2016-12-11 5:45 ` [PATCH 07/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 08/14] rtlwifi_new: rtl8192se: " Larry Finger
2016-12-11 5:45 ` [PATCH 08/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 09/14] rtlwifi_new: rtl8192de: " Larry Finger
2016-12-11 5:45 ` [PATCH 09/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` Larry Finger [this message]
2016-12-11 5:45 ` [PATCH 10/14] rtlwifi: rtl8192cu: " Larry Finger
2016-12-11 5:45 ` [PATCH 11/14] rtlwifi_new: rtl8192ce: " Larry Finger
2016-12-11 5:45 ` [PATCH 11/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 12/14] rtlwifi_new: rtl8192c-common: " Larry Finger
2016-12-11 5:45 ` [PATCH 12/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 13/14] rtlwifi_new: rtl8188ee: " Larry Finger
2016-12-11 5:45 ` [PATCH 13/14] rtlwifi: " Larry Finger
2016-12-11 5:45 ` [PATCH 14/14] rtlwifi: Remove some redundant code Larry Finger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20161211054523.7119-19-Larry.Finger@lwfinger.net \
--to=larry.finger@lwfinger.net \
--cc=devel@driverdev.osuosl.org \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=pkshih@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox