From: Stefan Wahren <stefan.wahren@i2se.com>
To: "Arend van Spriel" <arend.vanspriel@broadcom.com>,
"Rafał Miłecki" <rafal@milecki.pl>
Cc: linux-wireless <linux-wireless@vger.kernel.org>,
Chi-Hsien Lin <chi-hsien.lin@cypress.com>,
Wright Feng <wright.feng@cypress.com>,
Franky Lin <franky.lin@broadcom.com>,
Hante Meuleman <hante.meuleman@broadcom.com>
Subject: Re: brcmfmac: regression using AP mode
Date: Wed, 28 Nov 2018 21:13:56 +0100 (CET) [thread overview]
Message-ID: <638991280.323977.1543436036313@email.ionos.de> (raw)
In-Reply-To: <1820979779.200101.1543256045155@email.ionos.de>
Hi,
> Stefan Wahren <stefan.wahren@i2se.com> hat am 26. November 2018 um 19:14 geschrieben:
>
>
> Hi Arend,
>
> > Arend van Spriel <arend.vanspriel@broadcom.com> hat am 26. November 2018 um 11:11 geschrieben:
> >
> > So no AP listed here. I suspect Rafał was focusing on "device_ap_sme=1
> > use_monitor=1" scenario. You can try adding AP entry with similar rx
> > bits as P2P_GO above.
>
> thanks this make all driver errors like "setting AP mode failed -52" disappear, but now hostapd 2.6 seems to stuck in a loop during establishing the link:
>
i increased the debug level of brcmfmac to 0x5 and i'm getting this while booting:
[ 5.288806] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 5.289167] brcmfmac: brcmf_chip_recognition found AXI chip: BCM4345/6
[ 5.293319] brcmfmac: brcmf_chip_cores_check [1 ] core 0x800:51 base 0x18000000 wrap 0x18100000
[ 5.293333] brcmfmac: brcmf_chip_cores_check [2 ] core 0x812:54 base 0x18001000 wrap 0x18101000
[ 5.293344] brcmfmac: brcmf_chip_cores_check [3 ] core 0x83e:9 base 0x18002000 wrap 0x18102000
[ 5.293353] brcmfmac: brcmf_chip_cores_check [4 ] core 0x83c:14 base 0x18003000 wrap 0x18103000
[ 5.293362] brcmfmac: brcmf_chip_cores_check [5 ] core 0x829:21 base 0x18004000 wrap 0x18104000
[ 5.293371] brcmfmac: brcmf_chip_cores_check [6 ] core 0x135:0 base 0x00000000 wrap 0x18107000
[ 5.293379] brcmfmac: brcmf_chip_cores_check [7 ] core 0x240:0 base 0x00000000 wrap 0x00000000
[ 5.295574] brcmfmac: brcmf_chip_get_raminfo RAM: base=0x198000 size=819200 (0xc8000) sr=0 (0x0)
[ 5.295686] brcmfmac: brcmf_chip_setup ccrev=51, pmurev=27, pmucaps=0x39d05f1b
[ 5.295698] brcmfmac: brcmf_get_module_param Enter, bus=0, chip=17221, rev=6
[ 5.295765] brcmfmac: brcmf_sdio_drivestrengthinit No SDIO driver strength init needed for chip BCM4345/6 rev 6 pmurev 27
[ 5.296204] brcmfmac: brcmf_sdio_probe completed!!
[ 5.296219] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.413840] brcmfmac: brcmf_sdio_verifymemory Compare RAM dl & ul at 0x00198000; size=600487
[ 5.442090] random: crng init done
[ 5.442105] random: 7 urandom warning(s) missed due to ratelimiting
[ 5.539438] brcmfmac: brcmf_sdio_verifymemory Compare RAM dl & ul at 0x0025f940; size=1728
[ 5.636378] brcmfmac: brcmf_sdio_firmware_callback enable F2: err=0
[ 5.636577] brcmfmac: brcmf_bus_change_state ignoring transition, bus not attached yet
[ 5.636819] brcmfmac: brcmf_add_if allocate netdev interface
[ 5.637199] brcmfmac: brcmf_sdio_readshared sdpcm_shared address 0x001FF350
[ 5.638014] brcmfmac: brcmf_sdio_readshared sdpcm_shared address 0x001FF350
[ 5.641788] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 5.665557] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 5.666203] brcmfmac: brcmf_c_preinit_dcmds CLM version = API: 12.2 Data: 9.10.105 Compiler: 1.29.4 ClmImport: 1.36.3 Creation: 2018-03-09 18:56:28
[ 5.673860] brcmfmac: brcmf_feat_firmware_capabilities [ ap sta wme 802.11d 802.11h rm cqa cac dualband ampdu ampdu_tx ampdu_rx amsdurx tdls radio_pwrsave btamp p2p proptxstatus mchan p2po anqpo vht-prop-rates dfrts txpwrcache stbc-tx stbc-rx-1ss epno pfnx wnm bsstrans mfp ]
[ 5.673890] brcmfmac: brcmf_feat_firmware_capabilities enabling feature: MCHAN
[ 5.673899] brcmfmac: brcmf_feat_firmware_capabilities enabling feature: P2P
[ 5.674522] brcmfmac: brcmf_feat_iovar_int_get enabling feature: PNO
[ 5.675854] brcmfmac: brcmf_feat_iovar_int_get enabling feature: TDLS
[ 5.676955] brcmfmac: brcmf_feat_iovar_int_get enabling feature: MFP
[ 5.678014] brcmfmac: brcmf_feat_iovar_int_get enabling feature: FWSUP
[ 5.678066] brcmfmac: brcmf_fws_attach FWS queueing will be avoided
[ 5.678920] brcmfmac: brcmf_cfg80211_attach Registering custom regulatory
[ 5.681508] brcmfmac: brcmf_setup_wiphybands nmode=1, vhtmode=1, bw_cap=(1, 7)
[ 5.684720] brcmfmac: brcmf_setup_wiphybands nchain=1
[ 5.721118] brcmfmac: check_vif_up device is not ready : status (0)
[ 5.721190] brcmfmac: brcmf_net_attach wlan0: Broadcom Dongle Host Driver
[ 5.844422] Bluetooth: hci0: BCM4345C0 (003.001.025) build 0252
[ 10.845747] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.612740] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.613251] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.614724] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.616385] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.637118] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event
[ 11.638643] brcmfmac: brcmf_config_dongle power save set to enabled
[ 11.639137] brcmfmac: brcmf_dongle_roam Internal Roaming = On
[ 11.640504] brcmfmac: brcmf_cfg80211_change_iface IF Type = Infra
[ 11.642531] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.642545] brcmfmac: brcmf_cfg80211_set_power_mgmt power save enabled
[ 11.767278] brcmfmac: brcmf_p2p_add_vif adding vif "p2p-dev-wlan0" (type=10)
[ 11.789469] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event
[ 11.791667] brcmfmac: brcmf_add_if allocate non-netdev interface
[ 11.792237] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.792260] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.912572] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.913704] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.913881] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.914027] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.915150] brcmfmac: check_vif_up device is not ready : status (0)
[ 11.915230] brcmfmac: check_vif_up device is not ready : status (0)
[ 14.706985] brcmfmac: brcmf_cfg80211_connect ie (29d9d630), ie_len (28)
[ 17.638253] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 19.655039] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 21.780277] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 24.744917] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 24.995983] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 25.246750] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 25.446303] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 26.569338] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 28.692076] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
and this after starting hostapd 2.6:
[ 207.921068] brcmfmac: brcmf_btcoex_set_mode DHCP session ends
[ 207.921352] brcmfmac: brcmf_cfg80211_change_iface IF Type = AP
[ 209.114209] brcmfmac: brcmf_set_mpc MPC : 0
[ 209.143594] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event
[ 211.049412] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 213.051521] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 218.084704] brcmfmac: brcmf_escan_timeout: timer expired
[ 218.531282] brcmfmac: brcmf_add_if netdev:wlan0 ignore IF event
[ 218.531776] brcmfmac: brcmf_vif_set_mgmt_ie: vndr ie set error : -52
[ 218.532228] brcmfmac: brcmf_set_mpc MPC : 1
[ 218.533962] brcmfmac: brcmf_cfg80211_change_iface IF Type = Infra
[ 218.537955] brcmfmac: brcmf_cfg80211_connect ie (537583ca), ie_len (28)
[ 223.410796] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 225.526035] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 227.705830] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 227.956466] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 228.207019] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 228.407567] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 229.521312] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
[ 231.621031] brcmfmac: brcmf_netdev_start_xmit wlan0: insufficient headroom (0)
next prev parent reply other threads:[~2018-11-28 20:14 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-24 17:58 brcmfmac: regression using AP mode Stefan Wahren
2018-11-24 21:23 ` Rafał Miłecki
2018-11-25 13:14 ` Stefan Wahren
2018-11-26 10:11 ` Arend van Spriel
2018-11-26 18:14 ` Stefan Wahren
2018-11-28 20:13 ` Stefan Wahren [this message]
2018-11-29 10:42 ` James Hughes
2018-12-07 10:29 ` Stefan Wahren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=638991280.323977.1543436036313@email.ionos.de \
--to=stefan.wahren@i2se.com \
--cc=arend.vanspriel@broadcom.com \
--cc=chi-hsien.lin@cypress.com \
--cc=franky.lin@broadcom.com \
--cc=hante.meuleman@broadcom.com \
--cc=linux-wireless@vger.kernel.org \
--cc=rafal@milecki.pl \
--cc=wright.feng@cypress.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox