public inbox for linux-wireless@vger.kernel.org
 help / color / mirror / Atom feed
From: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
To: Deren Wu <deren.wu@mediatek.com>
Cc: Sean Wang <sean.wang@mediatek.com>, Felix Fietkau <nbd@nbd.name>,
	linux-wireless <linux-wireless@vger.kernel.org>
Subject: Re: [PATCH] mt76: mt7921: move mt7921_init_hw in a dedicated work
Date: Mon, 7 Mar 2022 15:27:56 +0100	[thread overview]
Message-ID: <YiYWbFLhV7+Sw9zM@lore-desk> (raw)
In-Reply-To: <700fc094dbca7406326dde1b169c2d2fe6a1bb24.camel@mediatek.com>

[-- Attachment #1: Type: text/plain, Size: 6384 bytes --]

> On Mon, 2022-03-07 at 13:00 +0100, Lorenzo Bianconi wrote:
> > > 
> > > Firmware initialization can take a while. Move mt7921_init_hw
> > > routine in
> > > a dedicated work in order to not slow down bootstrap process.
> > > 
> > > Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
> > 
> > Hi Sean and Deren,
> > 
> > I tested this patch on mt7921e and mt7921u. Can you double check if
> > it
> > works fine even on mt7921s? Thanks.
> > 
> > Regards,
> > Lorenzo
> 
> Hi Lore,

Hi Deren,

> 
> The patch is good on normal initial flow with mt7921s. However, if I
> run command "insmod mt7921s && rmmod mt7921s" quickly, there would be
> some problems in the remove process. The problem can be avoided if
> adding "cancel_work_sync(&dev->init_work)" in unregiser hook.
> 
> I think the patch is still good now and we may need another patch to
> cover the stress problem.
> 
> Tested-by: Deren Wu <deren.wu@mediatek.com>

ack, I will include it in v2 as soon as the other pending patches are applied.
Thanks.

Regards,
Lorenzo

> 
> 
> > 
> > > ---
> > >  .../net/wireless/mediatek/mt76/mt7921/init.c  | 66 +++++++++++++
> > > ------
> > >  .../wireless/mediatek/mt76/mt7921/mt7921.h    |  2 +
> > >  2 files changed, 49 insertions(+), 19 deletions(-)
> > > 
> > > diff --git a/drivers/net/wireless/mediatek/mt76/mt7921/init.c
> > > b/drivers/net/wireless/mediatek/mt76/mt7921/init.c
> > > index fa6af85bba7b..332af886b95a 100644
> > > --- a/drivers/net/wireless/mediatek/mt76/mt7921/init.c
> > > +++ b/drivers/net/wireless/mediatek/mt76/mt7921/init.c
> > > @@ -165,7 +165,7 @@ static int __mt7921_init_hardware(struct
> > > mt7921_dev *dev)
> > > 
> > >  static int mt7921_init_hardware(struct mt7921_dev *dev)
> > >  {
> > > -       int ret, idx, i;
> > > +       int ret, i;
> > > 
> > >         set_bit(MT76_STATE_INITIALIZED, &dev->mphy.state);
> > > 
> > > @@ -182,6 +182,13 @@ static int mt7921_init_hardware(struct
> > > mt7921_dev *dev)
> > >                 return ret;
> > >         }
> > > 
> > > +       return 0;
> > > +}
> > > +
> > > +static int mt7921_init_wcid(struct mt7921_dev *dev)
> > > +{
> > > +       int idx;
> > > +
> > >         /* Beacon and mgmt frames should occupy wcid 0 */
> > >         idx = mt76_wcid_alloc(dev->mt76.wcid_mask, MT7921_WTBL_STA
> > > - 1);
> > >         if (idx)
> > > @@ -195,6 +202,42 @@ static int mt7921_init_hardware(struct
> > > mt7921_dev *dev)
> > >         return 0;
> > >  }
> > > 
> > > +static void mt7921_init_work(struct work_struct *work)
> > > +{
> > > +       struct mt7921_dev *dev = container_of(work, struct
> > > mt7921_dev,
> > > +                                             init_work);
> > > +       int ret;
> > > +
> > > +       ret = mt7921_init_hardware(dev);
> > > +       if (ret)
> > > +               return;
> > > +
> > > +       mt76_set_stream_caps(&dev->mphy, true);
> > > +       mt7921_set_stream_he_caps(&dev->phy);
> > > +
> > > +       ret = mt76_register_device(&dev->mt76, true, mt76_rates,
> > > +                                  ARRAY_SIZE(mt76_rates));
> > > +       if (ret) {
> > > +               dev_err(dev->mt76.dev, "register device failed\n");
> > > +               return;
> > > +       }
> > > +
> > > +       ret = mt7921_init_debugfs(dev);
> > > +       if (ret) {
> > > +               dev_err(dev->mt76.dev, "debugfs register
> > > failed\n");
> > > +               goto error;
> > > +       }
> > > +
> > > +       ret = mt76_connac_mcu_set_deep_sleep(&dev->mt76, dev-
> > > >pm.ds_enable);
> > > +       if (ret)
> > > +               goto error;
> > > +
> > > +       dev->hw_init_done = true;
> > > +       return;
> > > +error:
> > > +       mt76_unregister_device(&dev->mt76);
> > > +}
> > > +
> > >  int mt7921_register_device(struct mt7921_dev *dev)
> > >  {
> > >         struct ieee80211_hw *hw = mt76_hw(dev);
> > > @@ -222,6 +265,7 @@ int mt7921_register_device(struct mt7921_dev
> > > *dev)
> > >         spin_lock_init(&dev->sta_poll_lock);
> > > 
> > >         INIT_WORK(&dev->reset_work, mt7921_mac_reset_work);
> > > +       INIT_WORK(&dev->init_work, mt7921_init_work);
> > > 
> > >         dev->pm.idle_timeout = MT7921_PM_TIMEOUT;
> > >         dev->pm.stats.last_wake_event = jiffies;
> > > @@ -234,7 +278,7 @@ int mt7921_register_device(struct mt7921_dev
> > > *dev)
> > >         if (mt76_is_sdio(&dev->mt76))
> > >                 hw->extra_tx_headroom += MT_SDIO_TXD_SIZE +
> > > MT_SDIO_HDR_SIZE;
> > > 
> > > -       ret = mt7921_init_hardware(dev);
> > > +       ret = mt7921_init_wcid(dev);
> > >         if (ret)
> > >                 return ret;
> > > 
> > > @@ -262,23 +306,7 @@ int mt7921_register_device(struct mt7921_dev
> > > *dev)
> > >         dev->mphy.hw->wiphy->available_antennas_rx = dev-
> > > >mphy.chainmask;
> > >         dev->mphy.hw->wiphy->available_antennas_tx = dev-
> > > >mphy.chainmask;
> > > 
> > > -       mt76_set_stream_caps(&dev->mphy, true);
> > > -       mt7921_set_stream_he_caps(&dev->phy);
> > > -
> > > -       ret = mt76_register_device(&dev->mt76, true, mt76_rates,
> > > -                                  ARRAY_SIZE(mt76_rates));
> > > -       if (ret)
> > > -               return ret;
> > > -
> > > -       ret = mt7921_init_debugfs(dev);
> > > -       if (ret)
> > > -               return ret;
> > > -
> > > -       ret = mt76_connac_mcu_set_deep_sleep(&dev->mt76, dev-
> > > >pm.ds_enable);
> > > -       if (ret)
> > > -               return ret;
> > > -
> > > -       dev->hw_init_done = true;
> > > +       queue_work(system_wq, &dev->init_work);
> > > 
> > >         return 0;
> > >  }
> > > diff --git a/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
> > > b/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
> > > index 394a677140da..b6c8f84acb64 100644
> > > --- a/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
> > > +++ b/drivers/net/wireless/mediatek/mt76/mt7921/mt7921.h
> > > @@ -204,6 +204,8 @@ struct mt7921_dev {
> > >         struct list_head sta_poll_list;
> > >         spinlock_t sta_poll_lock;
> > > 
> > > +       struct work_struct init_work;
> > > +
> > >         u8 fw_debug;
> > > 
> > >         struct mt76_connac_pm pm;
> > > --
> > > 2.35.1
> > > 
> > 
> > 
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

  reply	other threads:[~2022-03-07 14:28 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-03-07 11:58 [PATCH] mt76: mt7921: move mt7921_init_hw in a dedicated work Lorenzo Bianconi
2022-03-07 12:00 ` Lorenzo Bianconi
2022-03-07 13:35   ` Deren Wu
2022-03-07 14:27     ` Lorenzo Bianconi [this message]
2022-03-07 21:46 ` sean.wang
2022-03-07 22:47   ` Lorenzo Bianconi
2022-03-08  2:27     ` sean.wang
2022-03-13 12:53 ` Lorenzo Bianconi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=YiYWbFLhV7+Sw9zM@lore-desk \
    --to=lorenzo.bianconi@redhat.com \
    --cc=deren.wu@mediatek.com \
    --cc=linux-wireless@vger.kernel.org \
    --cc=nbd@nbd.name \
    --cc=sean.wang@mediatek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox