From: Bitterblue Smith <rtl8821cerfe2@gmail.com>
To: "David Härdeman" <david@hardeman.nu>,
"Ping-Ke Shih" <pkshih@realtek.com>,
linux-wireless@vger.kernel.org
Cc: linux-kernel@vger.kernel.org, Leonard Lausen <leonard@lausen.nl>,
Alastair D'Silva <alastair@d-silva.org>,
Luka Gejak <luka.gejak@linux.dev>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Jernej Skrabec <jernej.skrabec@gmail.com>
Subject: Re: [PATCH rtw-next 5/5] wifi: rtw88: sdio: read neighbouring registers of the 88xx chips at once
Date: Wed, 18 Nov 2026 17:56:15 +0200 [thread overview]
Message-ID: <eac5da81-b823-4f9e-ac85-add330c03b0b@gmail.com> (raw)
In-Reply-To: <20261116190145.2736364-6-david@hardeman.nu>
On 16/11/2026 21:01, David Härdeman wrote:
> Every register access costs a full SDIO command, about 40 us on a NanoPi
> R76S (RTL8822CS, SDR104), no matter how many bytes it moves. The
> interrupt handler reads HISR and then RX0_REQ_LEN, which follows it, and
> a free page sync reads the three REG_SDIO_FREE_TXPG words one by one.
>
> Read HISR together with RX0_REQ_LEN, and the three free page words, with
> one transfer each, as Realtek's driver does. As in rtw_sdio_readl(),
> this is only done while the chip is powered on; before that, and if the
> small DMA-safe buffers this needs could not be allocated, the registers
> are read one by one as before.
>
> On the R76S acting as an AP, TCP throughput to a client goes from about
> 170 to about 190 Mbit/s, the other directions are unchanged.
>
> Signed-off-by: David Härdeman <david@hardeman.nu>
> ---
> drivers/net/wireless/realtek/rtw88/sdio.c | 84 ++++++++++++++++++++---
> drivers/net/wireless/realtek/rtw88/sdio.h | 4 ++
> 2 files changed, 78 insertions(+), 10 deletions(-)
>
[...]
> diff --git a/drivers/net/wireless/realtek/rtw88/sdio.h b/drivers/net/wireless/realtek/rtw88/sdio.h
> index ab366f82d92..6aa59ed3db2 100644
> --- a/drivers/net/wireless/realtek/rtw88/sdio.h
> +++ b/drivers/net/wireless/realtek/rtw88/sdio.h
> @@ -188,6 +188,10 @@ struct rtw_sdio {
> bool free_txpg_valid;
> /* TX aggregation buffer of the non-8051 chips, under tx_credit_lock */
> u8 *tx_agg_buf;
> + /* non-8051 chips: HISR + RX0_REQ_LEN, read by the interrupt handler */
> + __le32 *rx_regs;
> + /* non-8051 chips: the REG_SDIO_FREE_TXPG words, under tx_credit_lock */
> + __le32 *txpg_regs;
> /* one writer at a time between the credit check and the accounting */
> struct mutex tx_credit_lock;
> };
By the way, you can call them "3081 chips".
next prev parent reply other threads:[~2026-11-18 15:56 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-16 19:01 [PATCH rtw-next 0/5] wifi: rtw88: sdio: faster and fairer TX for the 88xx chips David Härdeman
2026-11-16 19:01 ` [PATCH rtw-next 1/5] wifi: rtw88: sdio: cache the free TX page counts of " David Härdeman
2026-11-17 7:20 ` Luka Gejak
2026-11-17 12:50 ` David Härdeman
2026-11-16 19:01 ` [PATCH rtw-next 2/5] wifi: rtw88: sdio: aggregate TX frames " David Härdeman
2026-11-16 19:01 ` [PATCH rtw-next 3/5] wifi: rtw88: sdio: limit the TX queue length " David Härdeman
2026-11-17 7:21 ` Luka Gejak
2026-11-17 12:57 ` David Härdeman
2026-11-16 19:01 ` [PATCH rtw-next 4/5] wifi: rtw88: sdio: let TX in while receiving on " David Härdeman
2026-11-16 19:01 ` [PATCH rtw-next 5/5] wifi: rtw88: sdio: read neighbouring registers of the 88xx chips at once David Härdeman
2026-11-18 15:56 ` Bitterblue Smith [this message]
2026-11-16 21:59 ` [PATCH rtw-next 0/5] wifi: rtw88: sdio: faster and fairer TX for the 88xx chips Luka Gejak
2026-11-17 7:46 ` Ping-Ke Shih
2026-11-17 14:44 ` David Härdeman
2026-11-17 15:27 ` Luka Gejak
2026-11-18 10:54 ` David Härdeman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=eac5da81-b823-4f9e-ac85-add330c03b0b@gmail.com \
--to=rtl8821cerfe2@gmail.com \
--cc=alastair@d-silva.org \
--cc=david@hardeman.nu \
--cc=jernej.skrabec@gmail.com \
--cc=leonard@lausen.nl \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=luka.gejak@linux.dev \
--cc=martin.blumenstingl@googlemail.com \
--cc=pkshih@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox