* Re: [PATCH] ath10k: move irq setup
From: Kalle Valo @ 2013-07-30 18:35 UTC (permalink / raw)
To: Michal Kazior; +Cc: ath10k, linux-wireless
In-Reply-To: <1374129572-6079-1-git-send-email-michal.kazior@tieto.com>
Michal Kazior <michal.kazior@tieto.com> writes:
> There was a slight race during PCI shutdown. Since
> interrupts weren't really stopped (only Copy
> Engine interrupts were disabled through device hw
> registers) it was possible for a firmware
> indication (crash) interrupt to come in after
> tasklets were synced/killed. This would cause
> memory corruption and a panic in most cases. It
> was also possible for interrupt to come before CE
> was initialized during device probing.
>
> Interrupts are required for BMI phase so they are enabled as soon as
> power_up() is called but are freed upon both power_down() and stop()
> so there's asymmetry here. As by design stop() cannot be followed by
> start() it is okay. Both power_down() and stop() should be merged
> later on to avoid confusion.
Why are the interrupts freed both in power_down() and stop()? I don't
get that.
What if we call disable_irq() in power_down() instead?
> Before this can be really properly fixed var/hw
> init code split is necessary.
>
> Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
> ---
>
> Please note: this is based on my (still under
> review at the time of posting) previous patchests:
> device setup refactor and recovery.
>
> I'm posting this before those patchsets are merged
> so anyone interested in testing this fix (I can't
> reproduce the problem on my setup) can give it a
> try.
This was reported by Ben, right? So this sould have a Reported-by line
attributing him.
> @@ -1783,16 +1792,24 @@ static int ath10k_pci_hif_power_up(struct ath10k *ar)
> return 0;
>
> err_ce:
> + /* XXX: Until var/hw init is split it's impossible to fix the ordering
> + * here so we must call stop_intr() here too to prevent interrupts after
> + * CE is teared down. It's okay to double call the stop_intr()
> */
"FIXME:"
> exit:
> + ar_pci->intr_started = ret == 0;
A bit too clever for the sake of readibility for my taste, but I guess
it's ok.
> --- a/drivers/net/wireless/ath/ath10k/pci.h
> +++ b/drivers/net/wireless/ath/ath10k/pci.h
> @@ -198,6 +198,7 @@ struct ath10k_pci {
> * interrupts.
> */
> int num_msi_intrs;
> + bool intr_started;
Adding a new state variable makes me worried. I really would prefer a
solution which would not require that.
Also if we call request_irq() in ath10k_pci_probe() we should also call
free_irq() in ath10k_pci_remove() for symmetry. Just doing a temporary
hack will most likely stay forever :)
--
Kalle Valo
^ permalink raw reply
* Re: [PATCH v2] Documentation: dt: bindings: TI WiLink modules
From: Laurent Pinchart @ 2013-07-30 18:24 UTC (permalink / raw)
To: Luciano Coelho
Cc: devicetree-discuss, linux-doc, mturquette, mark.rutland, balbi,
grant.likely, rob.herring, linux-kernel, linux-omap,
linux-wireless, linux-arm, tony, nm
In-Reply-To: <1375109728-5931-1-git-send-email-coelho@ti.com>
Hi Luciano,
Thank you for the patch.
On Monday 29 July 2013 17:55:28 Luciano Coelho wrote:
> Add device tree bindings documentation for the TI WiLink modules.
> Currently only the WLAN part of the WiLink6, WiLink7 and WiLink8
> modules is supported.
>
> Signed-off-by: Luciano Coelho <coelho@ti.com>
> ---
>
> Changes in v2:
>
> Use generic clock definitions to get the clock data instead of passing
> the frequencies directly. Also added definition for "internal"
> ti,wilink-clock.
>
> Please review.
The proposal looks good to me, I just have one small comment.
> .../devicetree/bindings/net/wireless/ti-wilink.txt | 68 +++++++++++++++++++
> 1 file changed, 68 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/net/wireless/ti-wilink.txt
>
> diff --git a/Documentation/devicetree/bindings/net/wireless/ti-wilink.txt
> b/Documentation/devicetree/bindings/net/wireless/ti-wilink.txt new file
> mode 100644
> index 0000000..5fd27dc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wireless/ti-wilink.txt
> @@ -0,0 +1,68 @@
> +TI WiLink Wireless Modules Device Tree Bindings
> +===============================================
> +
> +The WiLink modules provide wireless connectivity, such as WLAN,
> +Bluetooth, FM and NFC.
> +
> +There are several different modules available, which can be grouped by
> +their generation: WiLink6, WiLink7 and WiLink8. WiLink4 is not
> +currently supported with device tree.
> +
> +Currently, only the WLAN portion of the modules is supported with
> +device tree.
> +
> +Required properties:
> +--------------------
> +
> +- compatible: should be "ti,wilink6", "ti,wilink7" or "ti,wilink8"
> +- interrupt-parent: the interrupt controller
> +- interrupts: out-of-band WLAN interrupt
> + See the interrupt controller's bindings documentation for
> + detailed definition.
> +
> +Optional properties:
> +--------------------
> +
> +- clocks: list of clocks needed by the chip as follows:
> +
> + refclock: the internal WLAN reference clock frequency (required for
> + WiLink6 and WiLink7; not used for WiLink8).
> +
> + tcxoclock: the internal WLAN TCXO clock frequency (required for
> + WiLink7 not used for WiLink6 and WiLink8).
> +
> + The clocks must be defined and named accordingly. For example:
> +
> + clocks = <&refclock>
> + clock-names = "refclock";
> +
> + refclock: refclock {
> + compatible = "ti,wilink-clock";
> + #clock-cells = <0>;
> + clock-frequency = <38400000>;
> + };
> +
> + Some modules that contain the WiLink chip provide clocks in the
> + module itself. In this case, we define a "ti,wilink-clock" as shown
> + above. But any other clock could in theory be used, so the proper
> + clock definition should be used.
> +
> +
> +Example:
> +--------
> +
> +Example definition that can be used in OMAP4 Panda:
> +
> +wlan {
> + compatible = "ti,wilink6";
> + interrupt-parent = <&gpio2>;
> + interrupts = <21 0x4>; /* gpio line 53, high level triggered */
Could you please use the IRQ_TYPE_LEVEL_HIGH macro (defined in <dt-
bindings/interrupt-controller/irq.h>) instead of the hardcode 0x4 constant ?
> + clocks = <&refclock>;
> + clock-names = "refclock";
> +
> + refclock: refclock {
> + compatible = "ti,wilink-clock";
> + #clock-cells = <0>;
> + clock-frequency = <38400000>;
> + };
> +};
--
Regards,
Laurent Pinchart
^ permalink raw reply
* [PATCH] MAINTAINERS: change email of TI WiLink drivers' maintainer
From: Luciano Coelho @ 2013-07-30 17:45 UTC (permalink / raw)
To: linux-wireless; +Cc: coelho, luca, balbi
Soon the coelho@ti.com email will not be valid anymore, so change it
to my private one.
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
MAINTAINERS | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index c6dc128..77be3f4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8278,7 +8278,7 @@ S: Maintained
F: sound/soc/codecs/twl4030*
TI WILINK WIRELESS DRIVERS
-M: Luciano Coelho <coelho@ti.com>
+M: Luciano Coelho <luca@coelho.fi>
L: linux-wireless@vger.kernel.org
W: http://wireless.kernel.org/en/users/Drivers/wl12xx
W: http://wireless.kernel.org/en/users/Drivers/wl1251
--
1.8.3.2
^ permalink raw reply related
* [PATCH 4/4] arm: dts: omap4-sdp: add WiLink7 device tree node
From: Luciano Coelho @ 2013-07-30 17:27 UTC (permalink / raw)
To: tony, linux-omap
Cc: devicetree, linux-arm-kernel, linux-wireless, coelho, luca, balbi
In-Reply-To: <1375205248-25708-1-git-send-email-coelho@ti.com>
Add appropriate device tree node for Blaze's WiLink7 module. It uses
a GPIO as interrupt, so configure the gpio2 node as interrupt parent
and assign the corresponding GPIO. Additionally, add the clock
frequencies used by the module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
arch/arm/boot/dts/omap4-sdp.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 3845615..2fecca1 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -150,6 +150,26 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ wlan {
+ compatible = "ti,wilink7";
+ interrupt-parent = <&gpio2>;
+ interrupts = <21 0x4>; /* gpio line 53, high level triggered */
+ clocks = <&refclock &tcxoclock>;
+ clock-names = "refclock tcxoclock";
+
+ refclock: refclock {
+ compatible = "ti,wilink-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ tcxoclock: tcxoclock {
+ compatible = "ti,wilink-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+ };
};
&omap4_pmx_wkup {
--
1.8.3.2
^ permalink raw reply related
* [PATCH 1/4] ARM: dts: omap4-panda: add MMC5 (WiLink WLAN) configuration
From: Luciano Coelho @ 2013-07-30 17:27 UTC (permalink / raw)
To: tony, linux-omap
Cc: devicetree, linux-arm-kernel, linux-wireless, coelho, luca, balbi
In-Reply-To: <1375205248-25708-1-git-send-email-coelho@ti.com>
Add regulator, pin muxing and MMC5 configuration to be used by the
on-board WiLink6 module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
arch/arm/boot/dts/omap4-panda-common.dtsi | 31 ++++++++++++++++++++++++++++++-
1 file changed, 30 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index faa95b5..b3f6e1f 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -107,6 +107,16 @@
*/
clock-frequency = <19200000>;
};
+
+ wilink_wl_en: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "wilink_wl_en";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio2 11 0>; /* gpio line 43 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
};
&omap4_pmx_wkup {
@@ -132,6 +142,7 @@
&dss_hdmi_pins
&tpd12s015_pins
&hsusbb1_pins
+ &wilink_pins
>;
twl6030_pins: pinmux_twl6030_pins {
@@ -235,6 +246,19 @@
0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
>;
};
+
+ wilink_pins: pinmux_wilink_pins {
+ pinctrl-single,pins = <
+ 0x7a 0x103 /* gpio_53 INPUT | MODE3 */
+ 0x66 0x3 /* gpio_43 OUTPUT | MODE3 */
+ 0x148 0x118 /* clk INPUT PULLUP | MODE0 */
+ 0x14a 0x118 /* cmd INPUT PULLUP | MODE0 */
+ 0x14c 0x118 /* dat0 INPUT PULLUP | MODE0 */
+ 0x14e 0x118 /* dat1 INPUT PULLUP | MODE0 */
+ 0x150 0x118 /* dat2 INPUT PULLUP | MODE0 */
+ 0x152 0x118 /* dat3 INPUT PULLUP | MODE0 */
+ >;
+ };
};
&i2c1 {
@@ -314,8 +338,13 @@
};
&mmc5 {
- ti,non-removable;
+ status = "okay";
+ vmmc-supply = <&wilink_wl_en>;
bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
};
&emif1 {
--
1.8.3.2
^ permalink raw reply related
* [PATCH 2/4] arm: dts: omap4-panda-common: add WiLink6 device tree nodes
From: Luciano Coelho @ 2013-07-30 17:27 UTC (permalink / raw)
To: tony, linux-omap
Cc: devicetree, linux-arm-kernel, linux-wireless, coelho, luca, balbi
In-Reply-To: <1375205248-25708-1-git-send-email-coelho@ti.com>
Add the WiLink device tree nodes. On omap4-panda, a WiLink6 module is
connected on MMC5 and a GPIO interrupt is used. The refclock
frequency is 38.4MHz.
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
arch/arm/boot/dts/omap4-panda-common.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index b3f6e1f..77e4a42 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -117,6 +117,20 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ wlan {
+ compatible = "ti,wilink6";
+ interrupt-parent = <&gpio2>;
+ interrupts = <21 0x4>; /* gpio line 53, high level triggered */
+ clocks = <&refclock>;
+ clock-names = "refclock";
+
+ refclock: refclock {
+ compatible = "ti,wilink-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ };
+ };
};
&omap4_pmx_wkup {
--
1.8.3.2
^ permalink raw reply related
* [PATCH 3/4] ARM: dts: omap4-sdp: add MMC5 (WiLink WLAN) configuration
From: Luciano Coelho @ 2013-07-30 17:27 UTC (permalink / raw)
To: tony, linux-omap
Cc: devicetree, linux-arm-kernel, linux-wireless, coelho, luca, balbi
In-Reply-To: <1375205248-25708-1-git-send-email-coelho@ti.com>
Add regulator, pin muxing and MMC5 configuration to be used by the
on-board WiLink6 module.
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
arch/arm/boot/dts/omap4-sdp.dts | 29 +++++++++++++++++++++++++++++
1 file changed, 29 insertions(+)
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 7951b4e..3845615 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -140,6 +140,16 @@
"DMic", "Digital Mic",
"Digital Mic", "Digital Mic1 Bias";
};
+
+ wilink_wl_en: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "wilink_wl_en";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio2 22 0>; /* gpio line 54 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
};
&omap4_pmx_wkup {
@@ -166,6 +176,7 @@
&mcbsp2_pins
&dss_hdmi_pins
&tpd12s015_pins
+ &wilink_pins
>;
uart2_pins: pinmux_uart2_pins {
@@ -295,6 +306,19 @@
0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
>;
};
+
+ wilink_pins: pinmux_wilink_pins {
+ pinctrl-single,pins = <
+ 0x7a 0x103 /* gpio_53 INPUT | MODE3 */
+ 0x7c 0x3 /* gpio_54 OUTPUT | MODE3 */
+ 0x148 0x118 /* clk INPUT PULLUP | MODE0 */
+ 0x14a 0x118 /* cmd INPUT PULLUP | MODE0 */
+ 0x14c 0x118 /* dat0 INPUT PULLUP | MODE0 */
+ 0x14e 0x118 /* dat1 INPUT PULLUP | MODE0 */
+ 0x150 0x118 /* dat2 INPUT PULLUP | MODE0 */
+ 0x152 0x118 /* dat3 INPUT PULLUP | MODE0 */
+ >;
+ };
};
&i2c1 {
@@ -420,8 +444,13 @@
};
&mmc5 {
+ status = "okay";
+ vmmc-supply = <&wilink_wl_en>;
bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
ti,non-removable;
+ ti,needs-special-hs-handling;
};
&emif1 {
--
1.8.3.2
^ permalink raw reply related
* [PATCH 0/4] ARM: dts: add WiLink support to panda and omap4-sdp
From: Luciano Coelho @ 2013-07-30 17:27 UTC (permalink / raw)
To: tony, linux-omap
Cc: devicetree, linux-arm-kernel, linux-wireless, coelho, luca, balbi
Hi,
These patches add the necessary DT configuration to use the WLAN part
of WiLink on OMAP4 Pandaboard and on OMAP4-SDP (including Blaze).
I've tested these changes on Panda and it works fine. But I couldn't
test the OMAP4 SDP changes properly on 3.11-rc3 because I'm having
problems with clocks and SDIO stuff. So it's pretty much just
compiled tested. I've tried this (without the new clock definition
stuff) on Blaze with 3.10 and it was working, though.
Please take a look and let me know what you think.
Luca.
Luciano Coelho (4):
ARM: dts: omap4-panda: add MMC5 (WiLink WLAN) configuration
arm: dts: omap4-panda-common: add WiLink6 device tree nodes
ARM: dts: omap4-sdp: add MMC5 (WiLink WLAN) configuration
arm: dts: omap4-sdp: add WiLink7 device tree node
arch/arm/boot/dts/omap4-panda-common.dtsi | 45 +++++++++++++++++++++++++++-
arch/arm/boot/dts/omap4-sdp.dts | 49 +++++++++++++++++++++++++++++++
2 files changed, 93 insertions(+), 1 deletion(-)
--
1.8.3.2
^ permalink raw reply
* Re: Passing a custom MAC to ath6kl
From: Priti @ 2013-07-29 11:14 UTC (permalink / raw)
To: linux-wireless
In-Reply-To: <51D70A22.20607@broadcom.com>
Hi,
i am looking for a way to update MAC address for ar6103.
i am using compat-wirless-3.4.rc3-1 package and linux 2.3.31 kernel.
i have tried many ways to hard code the mac address value just to see the
change in mac address.i am able to see the updated mac address while giving
the ifconfig command,but my device is not sending any packet and not getting
IP address.
i have been trying to dig each and every source file in ath6kl folder but
not able to figure out why i am not able to change the mac address.
can any one please tell me the exact steps to achieve this.
it will be really helpful.
THanks,
Priti
^ permalink raw reply
* Pull request: ath 20130730
From: Kalle Valo @ 2013-07-30 15:20 UTC (permalink / raw)
To: John W. Linville; +Cc: linux-wireless, ath10k
Hi John,
here's a new pull request containing just ath10k patches from Michal.
A major new feature is that we can now restart the firmware when it
crashes. For this Michal needed quite a few preparation patches. It's
now possible to to crash the firmware from debugfs, which makes it
easier to test the restart feature.
Michal also sent fixes and cleanup to various parts in the driver. Most
visible to users are RTS and fragmentation related fixes.
Please pull and do let me know if there are any problems.
Kalle
The following changes since commit 2cdf359a521bb72286b6714478dfdbcd2691f3fe:
mwifiex: code rearrangement in sdio.c (2013-07-26 16:57:45 -0400)
are available in the git repository at:
git://github.com/kvalo/ath6kl.git tags/for-linville-20130730
for you to fetch changes up to 424121c365aed6ec93bbc8b515548df79c5af61c:
ath10k: fix rts/fragmentation threshold setup (2013-07-30 18:01:21 +0300)
----------------------------------------------------------------
Michal Kazior (34):
ath10k: fix teardown ordering
ath10k: fix possible deadlock
ath10k: setup rts/frag thresholds upon vdev creation
ath10k: do not setup rts/frag thresholds for suspended interfaces
ath10k: remove ath10k_bus
ath10k: fix typo in define name
ath10k: silent warning in IBSS mode
ath10k: lower print level for a message
ath10k: provide errno if bmi read/write fails
ath10k: change function to take struct ath10k as arg
ath10k: rename hif callback
ath10k: embed HTC struct inside ath10k
ath10k: embed HTT struct inside ath10k
ath10k: improve locking
ath10k: abort scan properly if wmi_scan_stop fails
ath10k: add missing debug prints
ath10k: decouple pci start/stop logic
ath10k: decouple core start/stop logic
ath10k: allow deferred regd update
ath10k: reset BMI state upon init
ath10k: decouple suspend code
ath10k: move free_vdev_map initialization
ath10k: make sure all resources are freed upon ath10k_stop()
ath10k: defer hw setup to start/stop mac80211 hooks
ath10k: store firmware files in memory
ath10k: skip fw stats debugfs interface if device is down
ath10k: implement device recovery
ath10k: implement fw crash simulation command
ath10k: fix NULL dereference for injected packets
ath10k: create debugfs interface to trigger fw crash
ath10k: prevent HTC from being used after stopping
ath10k: don't reset HTC endpoints unnecessarily
ath10k: fix memleak in mac setup
ath10k: fix rts/fragmentation threshold setup
drivers/net/wireless/ath/ath10k/bmi.c | 12 +-
drivers/net/wireless/ath/ath10k/bmi.h | 1 +
drivers/net/wireless/ath/ath10k/ce.c | 2 +-
drivers/net/wireless/ath/ath10k/core.c | 321 +++++++++++++++--------
drivers/net/wireless/ath/ath10k/core.h | 50 +++-
drivers/net/wireless/ath/ath10k/debug.c | 87 ++++++-
drivers/net/wireless/ath/ath10k/hif.h | 49 +++-
drivers/net/wireless/ath/ath10k/htc.c | 61 ++---
drivers/net/wireless/ath/ath10k/htc.h | 8 +-
drivers/net/wireless/ath/ath10k/htt.c | 27 +-
drivers/net/wireless/ath/ath10k/htt.h | 3 +-
drivers/net/wireless/ath/ath10k/htt_rx.c | 3 +-
drivers/net/wireless/ath/ath10k/htt_tx.c | 12 +-
drivers/net/wireless/ath/ath10k/mac.c | 409 +++++++++++++++++++++++++-----
drivers/net/wireless/ath/ath10k/mac.h | 1 +
drivers/net/wireless/ath/ath10k/pci.c | 304 ++++++++++------------
drivers/net/wireless/ath/ath10k/pci.h | 4 +-
drivers/net/wireless/ath/ath10k/wmi.c | 40 ++-
drivers/net/wireless/ath/ath10k/wmi.h | 19 ++
19 files changed, 959 insertions(+), 454 deletions(-)
^ permalink raw reply
* RE: mwifiex: handle driver initialization error paths
From: Amitkumar Karwar @ 2013-07-30 13:38 UTC (permalink / raw)
To: 'Dan Carpenter'; +Cc: linux-wireless@vger.kernel.org
In-Reply-To: <20130729144754.GA7601@elgon.mountain>
Hi Dan,
>Hello Amitkumar Karwar,
>The patch 6b41f941d7cd: "mwifiex: handle driver initialization error
>paths" from Jul 22, 2013, leads to the following warning:
>"drivers/net/wireless/mwifiex/main.c:533 mwifiex_fw_dpc()
> warn: 'adapter' was already freed."
Thanks for pointing this out. We will fix this regression issue.
Regards,
Amitkumar Karwar
^ permalink raw reply
* [GIT] [3.11] NFC fixes
From: Samuel Ortiz @ 2013-07-30 13:08 UTC (permalink / raw)
To: John W. Linville; +Cc: Linux NFC, Linux Wireless
Hi John,
This is the first NFC fixes pull request for 3.11.
We only have one build failure fix for the NCI SPI transport layer
due to a missing CRC_CCITT Kconfig dependency.
Thanks in advance for pulling.
The following changes since commit 64b6f46f1141ad938e354f37af62e28da972e8eb:
ath9k_hw: Fix multicast search for AR9002 family (2013-07-18 16:22:00 -0400)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes.git tags/nfc-fixes-3.11-1
for you to fetch changes up to 7427b370e0aa6226c763af94fc5c4e3433383543:
NFC: Fix NCI over SPI build (2013-07-19 16:55:26 +0200)
----------------------------------------------------------------
Frederic Danis (1):
NFC: Fix NCI over SPI build
net/nfc/nci/Kconfig | 1 +
1 file changed, 1 insertion(+)
--
Intel Open Source Technology Centre
http://oss.intel.com/
^ permalink raw reply
* [PATCH v4 8/8] wlcore/wl12xx: check if we got correct clock data from DT
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
The fref and the tcxo clocks settings are optional in some platforms.
WiLink8 doesn't need either, so we don't check the values. WiLink 6
only needs the fref clock, so we check that it is valid or return with
an error. WiLink7 needs both clocks, if either is not available we
return with an error.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
drivers/net/wireless/ti/wl12xx/main.c | 20 +++++++++++++++++---
drivers/net/wireless/ti/wlcore/sdio.c | 4 ----
2 files changed, 17 insertions(+), 7 deletions(-)
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index a6c2a14..60d2ff4 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -927,6 +927,11 @@ static int wl128x_boot_clk(struct wl1271 *wl, int *selected_clock)
u16 sys_clk_cfg;
int ret;
+ if ((priv->ref_clock < 0) || (priv->tcxo_clock < 0)) {
+ wl1271_error("Missing fref and/or tcxo clock settings\n");
+ return -EINVAL;
+ }
+
/* For XTAL-only modes, FREF will be used after switching from TCXO */
if (priv->ref_clock == WL12XX_REFCLOCK_26_XTAL ||
priv->ref_clock == WL12XX_REFCLOCK_38_XTAL) {
@@ -976,6 +981,11 @@ static int wl127x_boot_clk(struct wl1271 *wl)
u32 clk;
int ret;
+ if (priv->ref_clock < 0) {
+ wl1271_error("Missing fref clock settings\n");
+ return -EINVAL;
+ }
+
if (WL127X_PG_GET_MAJOR(wl->hw_pg_ver) < 3)
wl->quirks |= WLCORE_QUIRK_END_OF_TRANSACTION;
@@ -1758,7 +1768,7 @@ static int wl12xx_setup(struct wl1271 *wl)
wlcore_set_ht_cap(wl, IEEE80211_BAND_5GHZ, &wl12xx_ht_cap);
wl12xx_conf_init(wl);
- if (!fref_param) {
+ if (!fref_param && (pdata->ref_clock_freq > 0)) {
priv->ref_clock = wl12xx_get_clock_idx(wl12xx_refclock_table,
pdata->ref_clock_freq,
pdata->ref_clock_xtal);
@@ -1769,6 +1779,8 @@ static int wl12xx_setup(struct wl1271 *wl)
return priv->ref_clock;
}
+ } else if (!fref_param) {
+ priv->ref_clock = -EINVAL;
} else {
if (!strcmp(fref_param, "19.2"))
priv->ref_clock = WL12XX_REFCLOCK_19;
@@ -1786,7 +1798,7 @@ static int wl12xx_setup(struct wl1271 *wl)
wl1271_error("Invalid fref parameter %s", fref_param);
}
- if (!tcxo_param) {
+ if (!fref_param && (pdata->tcxo_clock_freq > 0)) {
priv->tcxo_clock = wl12xx_get_clock_idx(wl12xx_tcxoclock_table,
pdata->tcxo_clock_freq,
true);
@@ -1796,7 +1808,9 @@ static int wl12xx_setup(struct wl1271 *wl)
return priv->tcxo_clock;
}
- } else {
+ } else if (!fref_param) {
+ priv->tcxo_clock = -EINVAL;
+ }else {
if (!strcmp(tcxo_param, "19.2"))
priv->tcxo_clock = WL12XX_TCXOCLOCK_19_2;
else if (!strcmp(tcxo_param, "26"))
diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 60fce49..c76eb66 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -252,20 +252,16 @@ static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
for_each_matching_node(clock_node, wlcore_sdio_of_clk_match_table)
of_fixed_clk_setup(clock_node);
- /* TODO: make sure we have this when needed (ie. for WL6 and WL7) */
glue->refclock = of_clk_get_by_name(np, "refclock");
if (IS_ERR(glue->refclock)) {
- dev_err(dev, "couldn't find refclock on the device tree\n");
glue->refclock = NULL;
} else {
clk_prepare_enable(glue->refclock);
pdata->ref_clock_freq = clk_get_rate(glue->refclock);
}
- /* TODO: make sure we have this when needed (ie. for WL7) */
glue->tcxoclock = of_clk_get_by_name(np, "tcxoclock");
if (IS_ERR(glue->tcxoclock)) {
- dev_err(dev, "couldn't find tcxoclock on the device tree\n");
glue->tcxoclock = NULL;
} else {
clk_prepare_enable(glue->tcxoclock);
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 7/8] wlcore: sdio: get clocks from device tree
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
Read the clock nodes from the device tree and use them to set the
frequency for the refclock and the tcxo clock.
Also, call sdio_set_drvdata() earlier, so the glue is already set in
the driver data when we call wlcore_get_pdata_from_of() and we don't
need to pass it as a parameter.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
drivers/net/wireless/ti/wlcore/sdio.c | 36 +++++++++++++++++++++++++++++++++--
1 file changed, 34 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 980bf3d..60fce49 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -53,6 +53,7 @@ static bool dump = false;
struct wl12xx_sdio_glue {
struct device *dev;
struct platform_device *core;
+ struct clk *refclock, *tcxoclock;
};
static const struct sdio_device_id wl1271_devices[] = {
@@ -224,6 +225,7 @@ static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
struct wl12xx_platform_data *pdata;
struct device_node *np = dev->of_node;
struct device_node *clock_node;
+ struct wl12xx_sdio_glue *glue = sdio_get_drvdata(dev_to_sdio_func(dev));
if (!np) {
np = of_find_matching_node(NULL, dev->driver->of_match_table);
@@ -250,6 +252,26 @@ static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
for_each_matching_node(clock_node, wlcore_sdio_of_clk_match_table)
of_fixed_clk_setup(clock_node);
+ /* TODO: make sure we have this when needed (ie. for WL6 and WL7) */
+ glue->refclock = of_clk_get_by_name(np, "refclock");
+ if (IS_ERR(glue->refclock)) {
+ dev_err(dev, "couldn't find refclock on the device tree\n");
+ glue->refclock = NULL;
+ } else {
+ clk_prepare_enable(glue->refclock);
+ pdata->ref_clock_freq = clk_get_rate(glue->refclock);
+ }
+
+ /* TODO: make sure we have this when needed (ie. for WL7) */
+ glue->tcxoclock = of_clk_get_by_name(np, "tcxoclock");
+ if (IS_ERR(glue->tcxoclock)) {
+ dev_err(dev, "couldn't find tcxoclock on the device tree\n");
+ glue->tcxoclock = NULL;
+ } else {
+ clk_prepare_enable(glue->tcxoclock);
+ pdata->ref_clock_freq = clk_get_rate(glue->tcxoclock);
+ }
+
goto out;
out_free:
@@ -294,6 +316,8 @@ static int wl1271_probe(struct sdio_func *func,
/* Use block mode for transferring over one block size of data */
func->card->quirks |= MMC_QUIRK_BLKSZ_FOR_BYTE_MODE;
+ sdio_set_drvdata(func, glue);
+
/* The pdata allocated here is freed when the device is freed,
* so we don't need an additional out label to free it in case
* of error further on.
@@ -319,8 +343,6 @@ static int wl1271_probe(struct sdio_func *func,
if (mmcflags & MMC_PM_KEEP_POWER)
pdev_data->pwr_in_suspend = true;
- sdio_set_drvdata(func, glue);
-
/* Tell PM core that we don't need the card to be powered now */
pm_runtime_put_noidle(&func->dev);
@@ -387,6 +409,16 @@ static void wl1271_remove(struct sdio_func *func)
{
struct wl12xx_sdio_glue *glue = sdio_get_drvdata(func);
+ if (glue->refclock) {
+ clk_disable_unprepare(glue->refclock);
+ clk_put(glue->refclock);
+ }
+
+ if (glue->tcxoclock) {
+ clk_disable_unprepare(glue->tcxoclock);
+ clk_put(glue->tcxoclock);
+ }
+
/* Undo decrement done above in wl1271_probe */
pm_runtime_get_noresume(&func->dev);
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 4/8] wl12xx: use frequency instead of enumerations for pdata clocks
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead. Also add a
boolean to specify whether the clock is XTAL or not.
Change all board files to reflect this.
Additionally, this reverts commit 26f45c (ARM: OMAP2+: Legacy support
for wl12xx when booted with devicetree), since this is not be needed
anymore, now that DT support for WiLink is implemented.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
arch/arm/mach-davinci/board-da850-evm.c | 3 +-
arch/arm/mach-omap2/board-omap3evm.c | 3 +-
arch/arm/mach-omap2/board-zoom-peripherals.c | 3 +-
arch/arm/mach-omap2/devices.c | 39 -------------------
drivers/net/wireless/ti/wl12xx/main.c | 58 +++++++++++++++++++++++++++-
drivers/net/wireless/ti/wl12xx/wl12xx.h | 28 ++++++++++++++
include/linux/wl12xx.h | 27 ++-----------
7 files changed, 93 insertions(+), 68 deletions(-)
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 03de2e9..6b2768f 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -1376,7 +1376,8 @@ static const short da850_wl12xx_pins[] __initconst = {
static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
.irq = -1,
- .board_ref_clock = WL12XX_REFCLOCK_38,
+ .ref_clock_freq = 38400000,
+ .ref_clock_xtal = false,
};
static __init int da850_wl12xx_init(void)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 9c7dfc5..4ccfcc0 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -460,7 +460,8 @@ static struct platform_device omap3evm_wlan_regulator = {
};
struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
+ .ref_clock_freq = 38400000,
+ .ref_clock_xtal = false,
};
#endif
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
index 4f84cf9..83a9a36 100644
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ b/arch/arm/mach-omap2/board-zoom-peripherals.c
@@ -244,7 +244,8 @@ static struct platform_device *zoom_devices[] __initdata = {
};
static struct wl12xx_platform_data omap_zoom_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_26, /* 26 MHz */
+ .ref_clock_freq = 26000000,
+ .ref_clock_xtal = false,
};
static struct omap2_hsmmc_info mmc[] = {
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 3c1279f..10e6126 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -8,7 +8,6 @@
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
@@ -19,7 +18,6 @@
#include <linux/of.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/omap4-keypad.h>
-#include <linux/wl12xx.h>
#include <linux/platform_data/mailbox-omap.h>
#include <asm/mach-types.h>
@@ -513,40 +511,6 @@ static void omap_init_vout(void)
static inline void omap_init_vout(void) {}
#endif
-#if IS_ENABLED(CONFIG_WL12XX)
-
-static struct wl12xx_platform_data wl12xx __initdata;
-
-void __init omap_init_wl12xx_of(void)
-{
- int ret;
-
- if (!of_have_populated_dt())
- return;
-
- if (of_machine_is_compatible("ti,omap4-sdp")) {
- wl12xx.board_ref_clock = WL12XX_REFCLOCK_26;
- wl12xx.board_tcxo_clock = WL12XX_TCXOCLOCK_26;
- wl12xx.irq = gpio_to_irq(53);
- } else if (of_machine_is_compatible("ti,omap4-panda")) {
- wl12xx.board_ref_clock = WL12XX_REFCLOCK_38;
- wl12xx.irq = gpio_to_irq(53);
- } else {
- return;
- }
-
- ret = wl12xx_set_platform_data(&wl12xx);
- if (ret) {
- pr_err("error setting wl12xx data: %d\n", ret);
- return;
- }
-}
-#else
-static inline void omap_init_wl12xx_of(void)
-{
-}
-#endif
-
/*-------------------------------------------------------------------------*/
static int __init omap2_init_devices(void)
@@ -570,9 +534,6 @@ static int __init omap2_init_devices(void)
omap_init_mcspi();
omap_init_sham();
omap_init_aes();
- } else {
- /* These can be removed when bindings are done */
- omap_init_wl12xx_of();
}
omap_init_sti();
omap_init_rng();
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index 1c627da..a6c2a14 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -1701,6 +1701,43 @@ static struct ieee80211_sta_ht_cap wl12xx_ht_cap = {
},
};
+static const struct wl12xx_clock wl12xx_refclock_table[] = {
+ { 19200000, false, WL12XX_REFCLOCK_19 },
+ { 26000000, false, WL12XX_REFCLOCK_26 },
+ { 26000000, true, WL12XX_REFCLOCK_26_XTAL },
+ { 38400000, false, WL12XX_REFCLOCK_38 },
+ { 38400000, true, WL12XX_REFCLOCK_38_XTAL },
+ { 52000000, false, WL12XX_REFCLOCK_52 },
+ { 0, false, 0 }
+};
+
+static const struct wl12xx_clock wl12xx_tcxoclock_table[] = {
+ { 16368000, true, WL12XX_TCXOCLOCK_16_368 },
+ { 16800000, true, WL12XX_TCXOCLOCK_16_8 },
+ { 19200000, true, WL12XX_TCXOCLOCK_19_2 },
+ { 26000000, true, WL12XX_TCXOCLOCK_26 },
+ { 32736000, true, WL12XX_TCXOCLOCK_32_736 },
+ { 33600000, true, WL12XX_TCXOCLOCK_33_6 },
+ { 38400000, true, WL12XX_TCXOCLOCK_38_4 },
+ { 52000000, true, WL12XX_TCXOCLOCK_52 },
+ { 0, false, 0 }
+};
+
+static int wl12xx_get_clock_idx(const struct wl12xx_clock *table,
+ u32 freq, bool xtal)
+{
+ int i = 0;
+
+ while(table[i].freq != 0) {
+ if ((table[i].freq == freq) &&
+ (table[i].xtal == xtal))
+ return table[i].hw_idx;
+ i++;
+ };
+
+ return -EINVAL;
+}
+
static int wl12xx_setup(struct wl1271 *wl)
{
struct wl12xx_priv *priv = wl->priv;
@@ -1722,7 +1759,16 @@ static int wl12xx_setup(struct wl1271 *wl)
wl12xx_conf_init(wl);
if (!fref_param) {
- priv->ref_clock = pdata->board_ref_clock;
+ priv->ref_clock = wl12xx_get_clock_idx(wl12xx_refclock_table,
+ pdata->ref_clock_freq,
+ pdata->ref_clock_xtal);
+ if (priv->ref_clock < 0) {
+ wl1271_error("Invalid ref_clock frequency (%d Hz, %s)",
+ pdata->ref_clock_freq,
+ pdata->ref_clock_xtal ? "XTAL" : "not XTAL");
+
+ return priv->ref_clock;
+ }
} else {
if (!strcmp(fref_param, "19.2"))
priv->ref_clock = WL12XX_REFCLOCK_19;
@@ -1741,7 +1787,15 @@ static int wl12xx_setup(struct wl1271 *wl)
}
if (!tcxo_param) {
- priv->tcxo_clock = pdata->board_tcxo_clock;
+ priv->tcxo_clock = wl12xx_get_clock_idx(wl12xx_tcxoclock_table,
+ pdata->tcxo_clock_freq,
+ true);
+ if (priv->tcxo_clock < 0) {
+ wl1271_error("Invalid tcxo_clock frequency (%d Hz)",
+ pdata->tcxo_clock_freq);
+
+ return priv->tcxo_clock;
+ }
} else {
if (!strcmp(tcxo_param, "19.2"))
priv->tcxo_clock = WL12XX_TCXOCLOCK_19_2;
diff --git a/drivers/net/wireless/ti/wl12xx/wl12xx.h b/drivers/net/wireless/ti/wl12xx/wl12xx.h
index 9e5484a..05f631b 100644
--- a/drivers/net/wireless/ti/wl12xx/wl12xx.h
+++ b/drivers/net/wireless/ti/wl12xx/wl12xx.h
@@ -79,4 +79,32 @@ struct wl12xx_priv {
struct wl127x_rx_mem_pool_addr *rx_mem_addr;
};
+/* Reference clock values */
+enum {
+ WL12XX_REFCLOCK_19 = 0, /* 19.2 MHz */
+ WL12XX_REFCLOCK_26 = 1, /* 26 MHz */
+ WL12XX_REFCLOCK_38 = 2, /* 38.4 MHz */
+ WL12XX_REFCLOCK_52 = 3, /* 52 MHz */
+ WL12XX_REFCLOCK_38_XTAL = 4, /* 38.4 MHz, XTAL */
+ WL12XX_REFCLOCK_26_XTAL = 5, /* 26 MHz, XTAL */
+};
+
+/* TCXO clock values */
+enum {
+ WL12XX_TCXOCLOCK_19_2 = 0, /* 19.2MHz */
+ WL12XX_TCXOCLOCK_26 = 1, /* 26 MHz */
+ WL12XX_TCXOCLOCK_38_4 = 2, /* 38.4MHz */
+ WL12XX_TCXOCLOCK_52 = 3, /* 52 MHz */
+ WL12XX_TCXOCLOCK_16_368 = 4, /* 16.368 MHz */
+ WL12XX_TCXOCLOCK_32_736 = 5, /* 32.736 MHz */
+ WL12XX_TCXOCLOCK_16_8 = 6, /* 16.8 MHz */
+ WL12XX_TCXOCLOCK_33_6 = 7, /* 33.6 MHz */
+};
+
+struct wl12xx_clock {
+ u32 freq;
+ bool xtal;
+ u8 hw_idx;
+};
+
#endif /* __WL12XX_PRIV_H__ */
diff --git a/include/linux/wl12xx.h b/include/linux/wl12xx.h
index ab90b1c..11491ad 100644
--- a/include/linux/wl12xx.h
+++ b/include/linux/wl12xx.h
@@ -26,28 +26,6 @@
#include <linux/err.h>
-/* Reference clock values */
-enum {
- WL12XX_REFCLOCK_19 = 0, /* 19.2 MHz */
- WL12XX_REFCLOCK_26 = 1, /* 26 MHz */
- WL12XX_REFCLOCK_38 = 2, /* 38.4 MHz */
- WL12XX_REFCLOCK_52 = 3, /* 52 MHz */
- WL12XX_REFCLOCK_38_XTAL = 4, /* 38.4 MHz, XTAL */
- WL12XX_REFCLOCK_26_XTAL = 5, /* 26 MHz, XTAL */
-};
-
-/* TCXO clock values */
-enum {
- WL12XX_TCXOCLOCK_19_2 = 0, /* 19.2MHz */
- WL12XX_TCXOCLOCK_26 = 1, /* 26 MHz */
- WL12XX_TCXOCLOCK_38_4 = 2, /* 38.4MHz */
- WL12XX_TCXOCLOCK_52 = 3, /* 52 MHz */
- WL12XX_TCXOCLOCK_16_368 = 4, /* 16.368 MHz */
- WL12XX_TCXOCLOCK_32_736 = 5, /* 32.736 MHz */
- WL12XX_TCXOCLOCK_16_8 = 6, /* 16.8 MHz */
- WL12XX_TCXOCLOCK_33_6 = 7, /* 33.6 MHz */
-};
-
struct wl1251_platform_data {
void (*set_power)(bool enable);
/* SDIO only: IRQ number if WLAN_IRQ line is used, 0 for SDIO IRQs */
@@ -57,8 +35,9 @@ struct wl1251_platform_data {
struct wl12xx_platform_data {
int irq;
- int board_ref_clock;
- int board_tcxo_clock;
+ int ref_clock_freq; /* in Hertz */
+ bool ref_clock_xtal; /* specify whether the clock is XTAL or not */
+ int tcxo_clock_freq; /* in Hertz, tcxo is always XTAL */
};
#ifdef CONFIG_WILINK_PLATFORM_DATA
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 6/8] wlcore: sdio: add wilink clock providers
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
Add refclock and tcxoclock as clock providers in WiLink. These clocks
are not accesible outside the WiLink module, but they are registered
in the clock framework anyway. Only the WiLink chip consumes these
clocks.
In theory, the WiLink chip could be connected to external clocks
instead of using these internal clocks, so make the clock consumer
code generic enough. If external clocks are used, then the internal
clock device tree nodes are not necessary, but the external ones must
be specified.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
drivers/net/wireless/ti/wlcore/sdio.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 9370d7e..980bf3d 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -34,6 +34,7 @@
#include <linux/wl12xx.h>
#include <linux/pm_runtime.h>
#include <linux/printk.h>
+#include <linux/clk-provider.h>
#include "wlcore.h"
#include "wl12xx_80211.h"
@@ -214,10 +215,15 @@ static struct wl1271_if_operations sdio_ops = {
.set_block_size = wl1271_sdio_set_block_size,
};
+static const struct of_device_id wlcore_sdio_of_clk_match_table[] = {
+ { .compatible = "ti,wilink-clock" },
+};
+
static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
{
struct wl12xx_platform_data *pdata;
struct device_node *np = dev->of_node;
+ struct device_node *clock_node;
if (!np) {
np = of_find_matching_node(NULL, dev->driver->of_match_table);
@@ -241,6 +247,9 @@ static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
goto out_free;
}
+ for_each_matching_node(clock_node, wlcore_sdio_of_clk_match_table)
+ of_fixed_clk_setup(clock_node);
+
goto out;
out_free:
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 5/8] wlcore: add initial device tree support to the sdio module
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
If platform data is not available, try to get the required information
from the device tree. Register an OF match table and parse the
appropriate device tree nodes.
Parse interrupt property only, for now.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
drivers/net/wireless/ti/wlcore/sdio.c | 69 ++++++++++++++++++++++++++++++++---
1 file changed, 63 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 4c7e8ac..9370d7e 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -30,7 +30,7 @@
#include <linux/mmc/sdio_ids.h>
#include <linux/mmc/card.h>
#include <linux/mmc/host.h>
-#include <linux/gpio.h>
+#include <linux/of_irq.h>
#include <linux/wl12xx.h>
#include <linux/pm_runtime.h>
#include <linux/printk.h>
@@ -214,6 +214,43 @@ static struct wl1271_if_operations sdio_ops = {
.set_block_size = wl1271_sdio_set_block_size,
};
+static struct wl12xx_platform_data *wlcore_get_pdata_from_of(struct device *dev)
+{
+ struct wl12xx_platform_data *pdata;
+ struct device_node *np = dev->of_node;
+
+ if (!np) {
+ np = of_find_matching_node(NULL, dev->driver->of_match_table);
+ if (!np) {
+ dev_notice(dev, "device tree node not available\n");
+ pdata = ERR_PTR(-ENODEV);
+ goto out;
+ }
+ }
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ dev_err(dev, "can't allocate platform data\n");
+ pdata = ERR_PTR(-ENODEV);
+ goto out;
+ }
+
+ pdata->irq = irq_of_parse_and_map(np, 0);
+ if (pdata->irq < 0) {
+ dev_err(dev, "can't get interrupt gpio from the device tree\n");
+ goto out_free;
+ }
+
+ goto out;
+
+out_free:
+ kfree(pdata);
+ pdata = ERR_PTR(-ENODEV);
+
+out:
+ return pdata;
+}
+
static int wl1271_probe(struct sdio_func *func,
const struct sdio_device_id *id)
{
@@ -248,11 +285,22 @@ static int wl1271_probe(struct sdio_func *func,
/* Use block mode for transferring over one block size of data */
func->card->quirks |= MMC_QUIRK_BLKSZ_FOR_BYTE_MODE;
+ /* The pdata allocated here is freed when the device is freed,
+ * so we don't need an additional out label to free it in case
+ * of error further on.
+ */
+
+ /* Try to get legacy platform data from the board file */
pdev_data->pdata = wl12xx_get_platform_data();
if (IS_ERR(pdev_data->pdata)) {
- ret = PTR_ERR(pdev_data->pdata);
- dev_err(glue->dev, "missing wlan platform data: %d\n", ret);
- goto out_free_glue;
+ dev_info(&func->dev,
+ "legacy platform data not found, trying device tree\n");
+
+ pdev_data->pdata = wlcore_get_pdata_from_of(&func->dev);
+ if (IS_ERR(pdev_data->pdata)) {
+ dev_err(&func->dev, "can't get platform data\n");
+ goto out_free_glue;
+ }
}
/* if sdio can keep power while host is suspended, enable wow */
@@ -386,16 +434,25 @@ static const struct dev_pm_ops wl1271_sdio_pm_ops = {
};
#endif
+static const struct of_device_id wlcore_sdio_of_match_table[] = {
+ { .compatible = "ti,wilink6" },
+ { .compatible = "ti,wilink7" },
+ { .compatible = "ti,wilink8" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, wlcore_sdio_of_match_table);
+
static struct sdio_driver wl1271_sdio_driver = {
.name = "wl1271_sdio",
.id_table = wl1271_devices,
.probe = wl1271_probe,
.remove = wl1271_remove,
-#ifdef CONFIG_PM
.drv = {
+#ifdef CONFIG_PM
.pm = &wl1271_sdio_pm_ops,
- },
#endif
+ .of_match_table = of_match_ptr(wlcore_sdio_of_match_table),
+ },
};
static int __init wl1271_init(void)
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 2/8] wlcore: set irq_flags in the board files instead of hiding behind a quirk
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
The platform_quirk element in the platform data was used to change the
way the IRQ is triggered. When set, the EDGE_IRQ quirk would change
the irqflags used and treat edge trigger differently from the rest.
Instead of hiding this irq flag setting behind the quirk, have the
board files set the flags during initialization. This will be more
meaningful than driver-specific quirks when we switch to DT.
Additionally, fix missing gpio_request() calls in the boarding files
(so that setting the flags actually works).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
---
arch/arm/mach-davinci/board-da850-evm.c | 8 +++++++-
arch/arm/mach-omap2/board-omap3evm.c | 19 ++++++++++++++++++
arch/arm/mach-omap2/board-zoom-peripherals.c | 30 +++++++++++++++++++++++++---
drivers/net/wireless/ti/wlcore/debugfs.c | 2 +-
drivers/net/wireless/ti/wlcore/main.c | 17 ++++++++--------
drivers/net/wireless/ti/wlcore/wlcore.h | 5 ++---
include/linux/wl12xx.h | 4 ----
7 files changed, 64 insertions(+), 21 deletions(-)
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index bea6793..03de2e9 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -1377,7 +1377,6 @@ static const short da850_wl12xx_pins[] __initconst = {
static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
.irq = -1,
.board_ref_clock = WL12XX_REFCLOCK_38,
- .platform_quirks = WL12XX_PLATFORM_QUIRK_EDGE_IRQ,
};
static __init int da850_wl12xx_init(void)
@@ -1408,6 +1407,13 @@ static __init int da850_wl12xx_init(void)
goto free_wlan_en;
}
+ ret = irq_set_irq_type(gpio_to_irq(DA850_WLAN_IRQ),
+ IRQ_TYPE_EDGE_RISING);
+ if (ret) {
+ pr_err("Could not set wl12xx irq type: %d\n", ret);
+ goto free;
+ }
+
da850_wl12xx_wlan_data.irq = gpio_to_irq(DA850_WLAN_IRQ);
ret = wl12xx_set_platform_data(&da850_wl12xx_wlan_data);
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 8c02626..9c7dfc5 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -614,12 +614,31 @@ static void __init omap3_evm_wl12xx_init(void)
/* WL12xx WLAN Init */
omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO);
+
+ ret = gpio_request_one(OMAP3EVM_WLAN_IRQ_GPIO, GPIOF_IN,
+ "OMAP3EVM_WLAN_IRQ_GPIO");
+ if (ret) {
+ pr_err("error requesting wl12xx gpio: %d\n", ret);
+ goto out;
+ }
+
+ ret = irq_set_irq_type(gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO),
+ IRQ_TYPE_LEVEL_HIGH);
+ if (ret) {
+ pr_err("error setting wl12xx irq type: %d\n", ret);
+ goto free;
+ }
+
ret = wl12xx_set_platform_data(&omap3evm_wlan_data);
if (ret)
pr_err("error setting wl12xx data: %d\n", ret);
ret = platform_device_register(&omap3evm_wlan_regulator);
if (ret)
pr_err("error registering wl12xx device: %d\n", ret);
+out:
+ return;
+free:
+ gpio_free(OMAP3EVM_WLAN_IRQ_GPIO);
#endif
}
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
index a90375d..4f84cf9 100644
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ b/arch/arm/mach-omap2/board-zoom-peripherals.c
@@ -339,16 +339,40 @@ static void enable_board_wakeup_source(void)
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
-void __init zoom_peripherals_init(void)
+static void __init zoom_wilink_init(void)
{
int ret;
omap_zoom_wlan_data.irq = gpio_to_irq(OMAP_ZOOM_WLAN_IRQ_GPIO);
- ret = wl12xx_set_platform_data(&omap_zoom_wlan_data);
- if (ret)
+ ret = gpio_request_one(OMAP_ZOOM_WLAN_IRQ_GPIO, GPIOF_IN,
+ "OMAP_ZOOM_WLAN_IRQ_GPIO");
+ if (ret) {
+ pr_err("error requesting wl12xx gpio: %d\n", ret);
+ goto out;
+ }
+
+ ret = irq_set_irq_type(gpio_to_irq(OMAP_ZOOM_WLAN_IRQ_GPIO),
+ IRQ_TYPE_LEVEL_HIGH);
+ if (ret) {
+ pr_err("error setting wl12xx irq type: %d\n", ret);
+ goto free;
+ }
+
+ ret = wl12xx_set_platform_data(&omap_zoom_wlan_data);
+ if (ret) {
pr_err("error setting wl12xx data: %d\n", ret);
+ goto free;
+ }
+out:
+ return;
+free:
+ gpio_free(OMAP_ZOOM_WLAN_IRQ_GPIO);
+}
+void __init zoom_peripherals_init(void)
+{
+ zoom_wilink_init();
omap_hsmmc_init(mmc);
omap_i2c_init();
pwm_add_table(zoom_pwm_lookup, ARRAY_SIZE(zoom_pwm_lookup));
diff --git a/drivers/net/wireless/ti/wlcore/debugfs.c b/drivers/net/wireless/ti/wlcore/debugfs.c
index e17630c..9544477 100644
--- a/drivers/net/wireless/ti/wlcore/debugfs.c
+++ b/drivers/net/wireless/ti/wlcore/debugfs.c
@@ -486,7 +486,7 @@ static ssize_t driver_state_read(struct file *file, char __user *user_buf,
DRIVER_STATE_PRINT_HEX(irq);
/* TODO: ref_clock and tcxo_clock were moved to wl12xx priv */
DRIVER_STATE_PRINT_HEX(hw_pg_ver);
- DRIVER_STATE_PRINT_HEX(platform_quirks);
+ DRIVER_STATE_PRINT_HEX(irq_flags);
DRIVER_STATE_PRINT_HEX(chip.id);
DRIVER_STATE_PRINT_STR(chip.fw_ver_str);
DRIVER_STATE_PRINT_STR(chip.phy_fw_ver_str);
diff --git a/drivers/net/wireless/ti/wlcore/main.c b/drivers/net/wireless/ti/wlcore/main.c
index b8db55c..11dab9a 100644
--- a/drivers/net/wireless/ti/wlcore/main.c
+++ b/drivers/net/wireless/ti/wlcore/main.c
@@ -27,6 +27,7 @@
#include <linux/vmalloc.h>
#include <linux/wl12xx.h>
#include <linux/interrupt.h>
+#include <linux/irq.h>
#include "wlcore.h"
#include "debug.h"
@@ -516,7 +517,7 @@ static int wlcore_irq_locked(struct wl1271 *wl)
* In case edge triggered interrupt must be used, we cannot iterate
* more than once without introducing race conditions with the hardirq.
*/
- if (wl->platform_quirks & WL12XX_PLATFORM_QUIRK_EDGE_IRQ)
+ if (wl->irq_flags & IRQF_TRIGGER_RISING)
loopcount = 1;
wl1271_debug(DEBUG_IRQ, "IRQ work");
@@ -5765,7 +5766,6 @@ struct ieee80211_hw *wlcore_alloc_hw(size_t priv_size, u32 aggr_buf_size,
wl->ap_ps_map = 0;
wl->ap_fw_ps_map = 0;
wl->quirks = 0;
- wl->platform_quirks = 0;
wl->system_hlid = WL12XX_SYSTEM_HLID;
wl->active_sta_count = 0;
wl->active_link_count = 0;
@@ -5901,7 +5901,7 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
struct platform_device *pdev = wl->pdev;
struct wlcore_platdev_data *pdev_data = pdev->dev.platform_data;
struct wl12xx_platform_data *pdata = pdev_data->pdata;
- unsigned long irqflags;
+
int ret;
if (fw) {
@@ -5928,16 +5928,15 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
wlcore_adjust_conf(wl);
wl->irq = platform_get_irq(pdev, 0);
- wl->platform_quirks = pdata->platform_quirks;
wl->if_ops = pdev_data->if_ops;
- if (wl->platform_quirks & WL12XX_PLATFORM_QUIRK_EDGE_IRQ)
- irqflags = IRQF_TRIGGER_RISING;
- else
- irqflags = IRQF_TRIGGER_HIGH | IRQF_ONESHOT;
+ wl->irq_flags = irq_get_trigger_type(wl->irq);
+
+ /* Since we don't use the primary handler, we must set ONESHOT */
+ wl->irq_flags |= IRQF_ONESHOT;
ret = request_threaded_irq(wl->irq, NULL, wlcore_irq,
- irqflags, pdev->name, wl);
+ wl->irq_flags, pdev->name, wl);
if (ret < 0) {
wl1271_error("request_irq() failed: %d", ret);
goto out_free_nvs;
diff --git a/drivers/net/wireless/ti/wlcore/wlcore.h b/drivers/net/wireless/ti/wlcore/wlcore.h
index 0034979..8306bde 100644
--- a/drivers/net/wireless/ti/wlcore/wlcore.h
+++ b/drivers/net/wireless/ti/wlcore/wlcore.h
@@ -185,6 +185,8 @@ struct wl1271 {
int irq;
+ int irq_flags;
+
spinlock_t wl_lock;
enum wlcore_state state;
@@ -384,9 +386,6 @@ struct wl1271 {
/* Quirks of specific hardware revisions */
unsigned int quirks;
- /* Platform limitations */
- unsigned int platform_quirks;
-
/* number of currently active RX BA sessions */
int ba_rx_session_count;
diff --git a/include/linux/wl12xx.h b/include/linux/wl12xx.h
index b516b4f..1bfcd19 100644
--- a/include/linux/wl12xx.h
+++ b/include/linux/wl12xx.h
@@ -59,13 +59,9 @@ struct wl12xx_platform_data {
int irq;
int board_ref_clock;
int board_tcxo_clock;
- unsigned long platform_quirks;
bool pwr_in_suspend;
};
-/* Platform does not support level trigger interrupts */
-#define WL12XX_PLATFORM_QUIRK_EDGE_IRQ BIT(0)
-
#ifdef CONFIG_WILINK_PLATFORM_DATA
int wl12xx_set_platform_data(const struct wl12xx_platform_data *data);
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 3/8] wlcore: remove pwr_in_suspend from platform data
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
The pwr_in_suspend flag depends on the MMC settings which can be
retrieved from the SDIO subsystem, so it doesn't need to be part of
the platform data structure. Move it to the platform device data that
is passed from SDIO to wlcore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
drivers/net/wireless/ti/wlcore/main.c | 3 +--
drivers/net/wireless/ti/wlcore/sdio.c | 2 +-
drivers/net/wireless/ti/wlcore/wlcore_i.h | 1 +
include/linux/wl12xx.h | 1 -
4 files changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/ti/wlcore/main.c b/drivers/net/wireless/ti/wlcore/main.c
index 11dab9a..e771de0 100644
--- a/drivers/net/wireless/ti/wlcore/main.c
+++ b/drivers/net/wireless/ti/wlcore/main.c
@@ -5900,7 +5900,6 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
struct wl1271 *wl = context;
struct platform_device *pdev = wl->pdev;
struct wlcore_platdev_data *pdev_data = pdev->dev.platform_data;
- struct wl12xx_platform_data *pdata = pdev_data->pdata;
int ret;
@@ -5947,7 +5946,7 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
if (!ret) {
wl->irq_wake_enabled = true;
device_init_wakeup(wl->dev, 1);
- if (pdata->pwr_in_suspend)
+ if (pdev_data->pwr_in_suspend)
wl->hw->wiphy->wowlan = &wlcore_wowlan_support;
}
#endif
diff --git a/drivers/net/wireless/ti/wlcore/sdio.c b/drivers/net/wireless/ti/wlcore/sdio.c
index 29ef249..4c7e8ac 100644
--- a/drivers/net/wireless/ti/wlcore/sdio.c
+++ b/drivers/net/wireless/ti/wlcore/sdio.c
@@ -260,7 +260,7 @@ static int wl1271_probe(struct sdio_func *func,
dev_dbg(glue->dev, "sdio PM caps = 0x%x\n", mmcflags);
if (mmcflags & MMC_PM_KEEP_POWER)
- pdev_data->pdata->pwr_in_suspend = true;
+ pdev_data->pwr_in_suspend = true;
sdio_set_drvdata(func, glue);
diff --git a/drivers/net/wireless/ti/wlcore/wlcore_i.h b/drivers/net/wireless/ti/wlcore/wlcore_i.h
index e5e1464..f2c4227 100644
--- a/drivers/net/wireless/ti/wlcore/wlcore_i.h
+++ b/drivers/net/wireless/ti/wlcore/wlcore_i.h
@@ -209,6 +209,7 @@ struct wl1271_if_operations {
struct wlcore_platdev_data {
struct wl12xx_platform_data *pdata;
struct wl1271_if_operations *if_ops;
+ bool pwr_in_suspend;
};
#define MAX_NUM_KEYS 14
diff --git a/include/linux/wl12xx.h b/include/linux/wl12xx.h
index 1bfcd19..ab90b1c 100644
--- a/include/linux/wl12xx.h
+++ b/include/linux/wl12xx.h
@@ -59,7 +59,6 @@ struct wl12xx_platform_data {
int irq;
int board_ref_clock;
int board_tcxo_clock;
- bool pwr_in_suspend;
};
#ifdef CONFIG_WILINK_PLATFORM_DATA
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 1/8] wl1251: split wl251 platform data to a separate structure
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
In-Reply-To: <1375189476-21557-1-git-send-email-coelho@ti.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 4 +--
arch/arm/mach-omap2/board-rx51-peripherals.c | 2 +-
drivers/net/wireless/ti/wilink_platform_data.c | 37 +++++++++++++++++++++-----
drivers/net/wireless/ti/wl1251/sdio.c | 12 ++++-----
drivers/net/wireless/ti/wl1251/spi.c | 2 +-
include/linux/wl12xx.h | 22 ++++++++++++++-
6 files changed, 62 insertions(+), 17 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index b1547a0..84d56e8 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -541,7 +541,7 @@ static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
static void __init pandora_wl1251_init(void)
{
- struct wl12xx_platform_data pandora_wl1251_pdata;
+ struct wl1251_platform_data pandora_wl1251_pdata;
int ret;
memset(&pandora_wl1251_pdata, 0, sizeof(pandora_wl1251_pdata));
@@ -555,7 +555,7 @@ static void __init pandora_wl1251_init(void)
goto fail_irq;
pandora_wl1251_pdata.use_eeprom = true;
- ret = wl12xx_set_platform_data(&pandora_wl1251_pdata);
+ ret = wl1251_set_platform_data(&pandora_wl1251_pdata);
if (ret < 0)
goto fail_irq;
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index 9c2dd10..01e5711 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -80,7 +80,7 @@ enum {
RX51_SPI_MIPID, /* LCD panel */
};
-static struct wl12xx_platform_data wl1251_pdata;
+static struct wl1251_platform_data wl1251_pdata;
static struct tsc2005_platform_data tsc2005_pdata;
#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
diff --git a/drivers/net/wireless/ti/wilink_platform_data.c b/drivers/net/wireless/ti/wilink_platform_data.c
index 998e958..a92bd3e 100644
--- a/drivers/net/wireless/ti/wilink_platform_data.c
+++ b/drivers/net/wireless/ti/wilink_platform_data.c
@@ -23,17 +23,17 @@
#include <linux/err.h>
#include <linux/wl12xx.h>
-static struct wl12xx_platform_data *platform_data;
+static struct wl12xx_platform_data *wl12xx_platform_data;
int __init wl12xx_set_platform_data(const struct wl12xx_platform_data *data)
{
- if (platform_data)
+ if (wl12xx_platform_data)
return -EBUSY;
if (!data)
return -EINVAL;
- platform_data = kmemdup(data, sizeof(*data), GFP_KERNEL);
- if (!platform_data)
+ wl12xx_platform_data = kmemdup(data, sizeof(*data), GFP_KERNEL);
+ if (!wl12xx_platform_data)
return -ENOMEM;
return 0;
@@ -41,9 +41,34 @@ int __init wl12xx_set_platform_data(const struct wl12xx_platform_data *data)
struct wl12xx_platform_data *wl12xx_get_platform_data(void)
{
- if (!platform_data)
+ if (!wl12xx_platform_data)
return ERR_PTR(-ENODEV);
- return platform_data;
+ return wl12xx_platform_data;
}
EXPORT_SYMBOL(wl12xx_get_platform_data);
+
+static struct wl1251_platform_data *wl1251_platform_data;
+
+int __init wl1251_set_platform_data(const struct wl1251_platform_data *data)
+{
+ if (wl1251_platform_data)
+ return -EBUSY;
+ if (!data)
+ return -EINVAL;
+
+ wl1251_platform_data = kmemdup(data, sizeof(*data), GFP_KERNEL);
+ if (!wl1251_platform_data)
+ return -ENOMEM;
+
+ return 0;
+}
+
+struct wl1251_platform_data *wl1251_get_platform_data(void)
+{
+ if (!wl1251_platform_data)
+ return ERR_PTR(-ENODEV);
+
+ return wl1251_platform_data;
+}
+EXPORT_SYMBOL(wl1251_get_platform_data);
diff --git a/drivers/net/wireless/ti/wl1251/sdio.c b/drivers/net/wireless/ti/wl1251/sdio.c
index e2b3d9c..b75a37a 100644
--- a/drivers/net/wireless/ti/wl1251/sdio.c
+++ b/drivers/net/wireless/ti/wl1251/sdio.c
@@ -227,7 +227,7 @@ static int wl1251_sdio_probe(struct sdio_func *func,
struct wl1251 *wl;
struct ieee80211_hw *hw;
struct wl1251_sdio *wl_sdio;
- const struct wl12xx_platform_data *wl12xx_board_data;
+ const struct wl1251_platform_data *wl1251_board_data;
hw = wl1251_alloc_hw();
if (IS_ERR(hw))
@@ -254,11 +254,11 @@ static int wl1251_sdio_probe(struct sdio_func *func,
wl->if_priv = wl_sdio;
wl->if_ops = &wl1251_sdio_ops;
- wl12xx_board_data = wl12xx_get_platform_data();
- if (!IS_ERR(wl12xx_board_data)) {
- wl->set_power = wl12xx_board_data->set_power;
- wl->irq = wl12xx_board_data->irq;
- wl->use_eeprom = wl12xx_board_data->use_eeprom;
+ wl1251_board_data = wl1251_get_platform_data();
+ if (!IS_ERR(wl1251_board_data)) {
+ wl->set_power = wl1251_board_data->set_power;
+ wl->irq = wl1251_board_data->irq;
+ wl->use_eeprom = wl1251_board_data->use_eeprom;
}
if (wl->irq) {
diff --git a/drivers/net/wireless/ti/wl1251/spi.c b/drivers/net/wireless/ti/wl1251/spi.c
index c7dc6fe..6bbbfe6 100644
--- a/drivers/net/wireless/ti/wl1251/spi.c
+++ b/drivers/net/wireless/ti/wl1251/spi.c
@@ -238,7 +238,7 @@ static const struct wl1251_if_operations wl1251_spi_ops = {
static int wl1251_spi_probe(struct spi_device *spi)
{
- struct wl12xx_platform_data *pdata;
+ struct wl1251_platform_data *pdata;
struct ieee80211_hw *hw;
struct wl1251 *wl;
int ret;
diff --git a/include/linux/wl12xx.h b/include/linux/wl12xx.h
index a54fe82..b516b4f 100644
--- a/include/linux/wl12xx.h
+++ b/include/linux/wl12xx.h
@@ -48,11 +48,15 @@ enum {
WL12XX_TCXOCLOCK_33_6 = 7, /* 33.6 MHz */
};
-struct wl12xx_platform_data {
+struct wl1251_platform_data {
void (*set_power)(bool enable);
/* SDIO only: IRQ number if WLAN_IRQ line is used, 0 for SDIO IRQs */
int irq;
bool use_eeprom;
+};
+
+struct wl12xx_platform_data {
+ int irq;
int board_ref_clock;
int board_tcxo_clock;
unsigned long platform_quirks;
@@ -68,6 +72,10 @@ int wl12xx_set_platform_data(const struct wl12xx_platform_data *data);
struct wl12xx_platform_data *wl12xx_get_platform_data(void);
+int wl1251_set_platform_data(const struct wl1251_platform_data *data);
+
+struct wl1251_platform_data *wl1251_get_platform_data(void);
+
#else
static inline
@@ -82,6 +90,18 @@ struct wl12xx_platform_data *wl12xx_get_platform_data(void)
return ERR_PTR(-ENODATA);
}
+static inline
+int wl1251_set_platform_data(const struct wl1251_platform_data *data)
+{
+ return -ENOSYS;
+}
+
+static inline
+struct wl1251_platform_data *wl1251_get_platform_data(void)
+{
+ return ERR_PTR(-ENODATA);
+}
+
#endif
#endif
--
1.8.3.2
^ permalink raw reply related
* [PATCH v4 0/8] wilink: add device tree support
From: Luciano Coelho @ 2013-07-30 13:04 UTC (permalink / raw)
To: linux-wireless, tony, nsekhar
Cc: coelho, luca, mturquette, mark.rutland, balbi, grant.likely,
rob.herring, devicetree-discuss, linux-doc, linux-kernel,
linux-omap, linux-arm-kernel, nm, martinez.javier
Hi,
This patch series adds device tree support to the wlcore_sdio driver,
which is used by WiLink6, WiLink7 and WiLink8.
The first patches do some clean-up to make the data needed in the
wilink device tree node smaller. The remaining patches implement the
actual device tree node parsing in wlcore_sdio.
Regarding the XTAL clock issues, for now we don't support XTAL mode
with DT, but I have sent a proposal for a small change in the clock
framework to support this, but it's still under discussions [1].
The DTS file changes will be sent separately, since they need to go
via different trees.
A new version of the bindings documentation has been sent [2] and, if
no more comments are given to it, I'll apply it via my tree.
[1] http://news.gmane.org/find-root.php?message_id=1372971912-10877-1-git-send-email-coelho@ti.com
[2] http://news.gmane.org/find-root.php?message_id=1375109728-5931-1-git-send-email-coelho@ti.com
Changes in v4:
* Rebased on top of 3.11-rc3 (eg. no more changes on the board files
that were removed);
* Use the new irq_get_trigger_type() instead of
irqd_get_trigger_type() (thanks Javier);
* Added some missing const's (thanks Felipe);
* Reverted Tony's workaround to get WiLink to work on Panda while DT
was not supported yet.
Please review.
Luciano Coelho (8):
wl1251: split wl251 platform data to a separate structure
wlcore: set irq_flags in the board files instead of hiding behind a
quirk
wlcore: remove pwr_in_suspend from platform data
wl12xx: use frequency instead of enumerations for pdata clocks
wlcore: add initial device tree support to the sdio module
wlcore: sdio: add wilink clock providers
wlcore: sdio: get clocks from device tree
wlcore/wl12xx: check if we got correct clock data from DT
arch/arm/mach-davinci/board-da850-evm.c | 11 ++-
arch/arm/mach-omap2/board-omap3evm.c | 22 ++++-
arch/arm/mach-omap2/board-omap3pandora.c | 4 +-
arch/arm/mach-omap2/board-rx51-peripherals.c | 2 +-
arch/arm/mach-omap2/board-zoom-peripherals.c | 33 +++++++-
arch/arm/mach-omap2/devices.c | 39 ---------
drivers/net/wireless/ti/wilink_platform_data.c | 37 ++++++--
drivers/net/wireless/ti/wl1251/sdio.c | 12 +--
drivers/net/wireless/ti/wl1251/spi.c | 2 +-
drivers/net/wireless/ti/wl12xx/main.c | 78 +++++++++++++++--
drivers/net/wireless/ti/wl12xx/wl12xx.h | 28 +++++++
drivers/net/wireless/ti/wlcore/debugfs.c | 2 +-
drivers/net/wireless/ti/wlcore/main.c | 20 ++---
drivers/net/wireless/ti/wlcore/sdio.c | 112 +++++++++++++++++++++++--
drivers/net/wireless/ti/wlcore/wlcore.h | 5 +-
drivers/net/wireless/ti/wlcore/wlcore_i.h | 1 +
include/linux/wl12xx.h | 52 +++++-------
17 files changed, 340 insertions(+), 120 deletions(-)
--
1.8.3.2
^ permalink raw reply
* pull request: bluetooth 2013-07-30
From: Gustavo Padovan @ 2013-07-30 12:38 UTC (permalink / raw)
To: linville; +Cc: linux-wireless, linux-bluetooth, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 2291 bytes --]
Hi John,
A few fixes and devices ID additions for 3.11:
* There are 4 new ath3k device ids
* Fixed stack memory usage in ath3k.
* Fixed the init process of BlueFRITZ! devices, they were failing to init
due to an unsupported command we sent.
* Fixed wrong use of PTR_ERR in btusb code that was preventing intel devices
to work properly.
* Fixed race condition between hci_register_dev() and hci_dev_open() that
could cause a NULL pointer dereference.
* Fixed race condition that could call hci_req_cmd_complete() and make some
devices to fail as showed in the log added to the commit message.
Please pull or let me know of any issues. Thanks.
Gustavo
--
The following changes since commit 075163bbb0f51174359947e1bce84f5edb23f21e:
ath9k_htc: Handle IDLE state transition properly (2013-06-24 13:52:52 -0400)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth master
for you to fetch changes up to 53e21fbc288218a423959f878c86471a0e323a9a:
Bluetooth: Fix calling request callback more than once (2013-07-29 12:28:04 +0100)
----------------------------------------------------------------
AceLan Kao (2):
Bluetooth: Add support for Atheros [0cf3:3121]
Bluetooth: Add support for Atheros [0cf3:e003]
Adam Lee (1):
Bluetooth: fix wrong use of PTR_ERR() in btusb
Gustavo Padovan (1):
Bluetooth: Fix race between hci_register_dev() and hci_dev_open()
Jaganath Kanakkassery (1):
Bluetooth: Fix invalid length check in l2cap_information_rsp()
Johan Hedberg (2):
Bluetooth: Fix HCI init for BlueFRITZ! devices
Bluetooth: Fix calling request callback more than once
Stanislaw Gruszka (1):
Bluetooth: ath3k: don't use stack memory for DMA
Sujith Manoharan (1):
Bluetooth: ath3k: Add support for ID 0x13d3/0x3402
Thomas Loo (1):
Bluetooth: ath3k: Add support for Fujitsu Lifebook UH5x2 [04c5:1330]
drivers/bluetooth/ath3k.c | 46 +++++++++++++++++++++++++++++++++++++---------
drivers/bluetooth/btusb.c | 18 +++++++++++-------
net/bluetooth/hci_core.c | 26 +++++++++++++++++---------
net/bluetooth/l2cap_core.c | 2 +-
4 files changed, 66 insertions(+), 26 deletions(-)
[-- Attachment #2: Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply
* Re: How to read WiFi radio frequency.
From: KATSUMI masanori @ 2013-07-30 11:22 UTC (permalink / raw)
To: linux-wireless
In-Reply-To: <20130725210249.89DD.635158EF@elwsc.co.jp>
On Thu, 25 Jul 2013 21:02:51 +0900
KATSUMI masanori <masanori-katsumi@elwsc.co.jp> wrote:
> I am trying to make p2p software with the current device as the group
> owner.
> I would like to acquire the channel that GO started, from normal user(NOT
> root).
> How can I get this information?
I think I can get own GO operating channel or freq through NL80211_ATTR_WIPHY_FREQ attribute
in nl80211 interface.
However, I was not able to get this attribute by NL80211_CMD_GET_INTERFACE which is used in
iw command.
In addition to that, I tried several nl80211 commands but I couldn't get it.
e.g)
NL80211_CMD_GET_WIPHY
NL80211_CMD_GET_INTERFACE
NL80211_CMD_GET_SCAN
NL80211_CMD_GET_SURVEY
NL80211_CMD_REMAIN_ON_CHANNEL
I can get the operating freq during STA but I cannot find the way to
get the own operating freq during running GO.
BTW, NL80211_CMD_FRAME_TX_STATUS event is only notified when GO started.
But, even this event didn't contain the frequency information.
Is there any other way to get the own GO's operating channel ??
I tried kernel v3.0.31
And do you know this feature supports in the latest kernel ??
Regards,
^ permalink raw reply
* [PATCH] mac80211: allow lowest basic rate for unicast management frame in mesh
From: Chun-Yeow Yeoh @ 2013-07-30 1:48 UTC (permalink / raw)
To: linux-wireless; +Cc: johannes, linville, devel, Chun-Yeow Yeoh
Allow lowest basic rate to be used for unicast management frame in
mesh. Otherwise, the lowest supported rate is used for unicast
management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename
the rc_send_low_broadcast to re_send_low_basicrate since now it is
also applied to unicast management frame in mesh.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
---
net/mac80211/rate.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/net/mac80211/rate.c b/net/mac80211/rate.c
index ba63ac8..8038d47 100644
--- a/net/mac80211/rate.c
+++ b/net/mac80211/rate.c
@@ -210,7 +210,7 @@ static bool rc_no_data_or_no_ack_use_min(struct ieee80211_tx_rate_control *txrc)
!ieee80211_is_data(fc);
}
-static void rc_send_low_broadcast(s8 *idx, u32 basic_rates,
+static void rc_send_low_basicrate(s8 *idx, u32 basic_rates,
struct ieee80211_supported_band *sband)
{
u8 i;
@@ -269,6 +269,7 @@ bool rate_control_send_low(struct ieee80211_sta *sta,
{
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(txrc->skb);
struct ieee80211_supported_band *sband = txrc->sband;
+ struct sta_info *sta_mesh = container_of(sta, struct sta_info, sta);
int mcast_rate;
if (!sta || !priv_sta || rc_no_data_or_no_ack_use_min(txrc)) {
@@ -281,10 +282,16 @@ bool rate_control_send_low(struct ieee80211_sta *sta,
return true;
}
- rc_send_low_broadcast(&info->control.rates[0].idx,
+ rc_send_low_basicrate(&info->control.rates[0].idx,
txrc->bss_conf->basic_rates,
sband);
}
+
+ if (sta && ieee80211_vif_is_mesh(&sta_mesh->sdata->vif))
+ rc_send_low_basicrate(&info->control.rates[0].idx,
+ txrc->bss_conf->basic_rates,
+ sband);
+
return true;
}
return false;
--
1.7.9.5
^ permalink raw reply related
* [PATCH 3.11 2/3] mwifiex: fix wrong data rates in P2P client
From: Bing Zhao @ 2013-07-29 23:32 UTC (permalink / raw)
To: linux-wireless
Cc: John W. Linville, Avinash Patil, Stone Piao, Amitkumar Karwar,
Nishant Sarmukadam, Frank Huang, Bing Zhao
In-Reply-To: <1375140759-29767-1-git-send-email-bzhao@marvell.com>
From: Avinash Patil <patila@marvell.com>
This patch fixes an issue wherein adhoc rates were being copied
into association request from P2P client.
Cc: <stable@vger.kernel.org> # 3.10.y
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
---
drivers/net/wireless/mwifiex/cfp.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/mwifiex/cfp.c b/drivers/net/wireless/mwifiex/cfp.c
index 988552d..5178c46 100644
--- a/drivers/net/wireless/mwifiex/cfp.c
+++ b/drivers/net/wireless/mwifiex/cfp.c
@@ -415,7 +415,8 @@ u32 mwifiex_get_supported_rates(struct mwifiex_private *priv, u8 *rates)
u32 k = 0;
struct mwifiex_adapter *adapter = priv->adapter;
- if (priv->bss_mode == NL80211_IFTYPE_STATION) {
+ if (priv->bss_mode == NL80211_IFTYPE_STATION ||
+ priv->bss_mode == NL80211_IFTYPE_P2P_CLIENT) {
switch (adapter->config_bands) {
case BAND_B:
dev_dbg(adapter->dev, "info: infra band=%d "
--
1.8.2.3
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox