From: "Rafał Miłecki" <zajec5@gmail.com>
To: "linux-wireless@vger.kernel.org" <linux-wireless@vger.kernel.org>,
"John W. Linville" <linville@tuxdriver.com>
Cc: "bcm43xx-dev@lists.berlios.de" <bcm43xx-dev@lists.berlios.de>
Subject: [PATCH 2/7] b43: N-PHY: implement TX PHY cleanup and setup
Date: Sun, 17 Jan 2010 13:03:32 +0100 [thread overview]
Message-ID: <op.u6oef6cl9lhzdc@linux-g0th.site> (raw)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
---
drivers/net/wireless/b43/phy_n.c | 112 +++++++++++++++++++++++++++++++++++++-
1 files changed, 110 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c
index 4a1853b..34dd4a2 100644
--- a/drivers/net/wireless/b43/phy_n.c
+++ b/drivers/net/wireless/b43/phy_n.c
@@ -1505,6 +1505,114 @@ static struct nphy_txgains b43_nphy_get_tx_gains(struct b43_wldev *dev)
return target;
}
+/* http://bcm-v4.sipsolutions.net/802.11/PHY/N/TxCalPhyCleanup */
+static void b43_nphy_tx_cal_phy_cleanup(struct b43_wldev *dev)
+{
+ u16 *regs = dev->phy.n->tx_rx_cal_phy_saveregs;
+
+ if (dev->phy.rev >= 3) {
+ b43_phy_write(dev, B43_NPHY_AFECTL_C1, regs[0]);
+ b43_phy_write(dev, B43_NPHY_AFECTL_C2, regs[1]);
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER1, regs[2]);
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER, regs[3]);
+ b43_phy_write(dev, B43_NPHY_BBCFG, regs[4]);
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 3,
+ width 16, and data from regs[5] */
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 19,
+ width 16, and data from regs[6] */
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC1, regs[7]);
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC2, regs[8]);
+ b43_phy_write(dev, B43_NPHY_PAPD_EN0, regs[9]);
+ b43_phy_write(dev, B43_NPHY_PAPD_EN1, regs[10]);
+ b43_nphy_reset_cca(dev);
+ } else {
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C1, 0x0FFF, regs[0]);
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C2, 0x0FFF, regs[1]);
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER, regs[2]);
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 2,
+ width 16, and data from regs[3] */
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 18,
+ width 16, and data from regs[4] */
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC1, regs[5]);
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC2, regs[6]);
+ }
+}
+
+/* http://bcm-v4.sipsolutions.net/802.11/PHY/N/TxCalPhySetup */
+static void b43_nphy_tx_cal_phy_setup(struct b43_wldev *dev)
+{
+ u16 *regs = dev->phy.n->tx_rx_cal_phy_saveregs;
+ u16 tmp;
+
+ regs[0] = b43_phy_read(dev, B43_NPHY_AFECTL_C1);
+ regs[1] = b43_phy_read(dev, B43_NPHY_AFECTL_C2);
+ if (dev->phy.rev >= 3) {
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C1, 0xF0FF, 0x0A00);
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C2, 0xF0FF, 0x0A00);
+
+ tmp = b43_phy_read(dev, B43_NPHY_AFECTL_OVER1);
+ regs[2] = tmp;
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER1, tmp | 0x0600);
+
+ tmp = b43_phy_read(dev, B43_NPHY_AFECTL_OVER);
+ regs[3] = tmp;
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER, tmp | 0x0600);
+
+ regs[4] = b43_phy_read(dev, B43_NPHY_BBCFG);
+ b43_phy_mask(dev, B43_NPHY_BBCFG, ~B43_NPHY_BBCFG_RSTRX);
+
+ /* TODO: Read an N PHY Table with ID 8, length 1, offset 3,
+ width 16, and data pointing to tmp */
+ regs[5] = tmp;
+
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 3,
+ width 16, and data 0 */
+ /* TODO: Read an N PHY Table with ID 8, length 1, offset 19,
+ width 16, and data pointing to tmp */
+ regs[6] = tmp;
+
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 19,
+ width 16, and data 0 */
+ regs[7] = b43_phy_read(dev, B43_NPHY_RFCTL_INTC1);
+ regs[8] = b43_phy_read(dev, B43_NPHY_RFCTL_INTC2);
+
+ /* TODO: Call N PHY RF Ctrl Intc Override with 2, 1, 3 */
+ /* TODO: Call N PHY RF Ctrl Intc Override with 1, 2, 1 */
+ /* TODO: Call N PHY RF Ctrl Intc Override with 1, 8, 2 */
+
+ regs[9] = b43_phy_read(dev, B43_NPHY_PAPD_EN0);
+ regs[10] = b43_phy_read(dev, B43_NPHY_PAPD_EN1);
+ b43_phy_mask(dev, B43_NPHY_PAPD_EN0, ~0x0001);
+ b43_phy_mask(dev, B43_NPHY_PAPD_EN1, ~0x0001);
+ } else {
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C1, 0x0FFF, 0xA000);
+ b43_phy_maskset(dev, B43_NPHY_AFECTL_C2, 0x0FFF, 0xA000);
+ tmp = b43_phy_read(dev, B43_NPHY_AFECTL_OVER);
+ regs[2] = tmp;
+ b43_phy_write(dev, B43_NPHY_AFECTL_OVER, tmp | 0x3000);
+ /* TODO: Read an N PHY Table with ID 8, length 1, offset 2,
+ width 16, and data pointing to tmp */
+ regs[3] = tmp;
+ tmp |= 0x2000;
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 2,
+ width 16, and data pointer tmp */
+ /* TODO: Read an N PHY Table with ID 8, length 1, offset 18,
+ width 16, and data pointer tmp */
+ regs[4] = tmp;
+ tmp |= 0x2000;
+ /* TODO: Write an N PHY Table with ID 8, length 1, offset 18,
+ width 16, and data pointer tmp */
+ regs[5] = b43_phy_read(dev, B43_NPHY_RFCTL_INTC1);
+ regs[6] = b43_phy_read(dev, B43_NPHY_RFCTL_INTC2);
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ)
+ tmp = 0x0180;
+ else
+ tmp = 0x0120;
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC1, tmp);
+ b43_phy_write(dev, B43_NPHY_RFCTL_INTC2, tmp);
+ }
+}
+
/* http://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal */
static void b43_nphy_restore_cal(struct b43_wldev *dev)
{
@@ -1617,7 +1725,7 @@ static int b43_nphy_cal_tx_iq_lo(struct b43_wldev *dev,
width 16, and data pointer gain */
b43_nphy_tx_cal_radio_setup(dev);
- /* TODO: Call N PHY TX Cal PHY Setup */
+ b43_nphy_tx_cal_phy_setup(dev);
phy6or5x = dev->phy.rev >= 6 ||
(dev->phy.rev == 5 && nphy->ipa2g_on &&
@@ -1788,7 +1896,7 @@ static int b43_nphy_cal_tx_iq_lo(struct b43_wldev *dev,
b43_phy_write(dev, B43_NPHY_IQLOCAL_CMDGCTL, 0);
}
- /* TODO: Call N PHY TX Cal PHY Cleanup */
+ b43_nphy_tx_cal_phy_cleanup(dev);
/* TODO: Write an N PHY Table with ID 7, length 2, offset 0x110,
width 16, and data from save */
--
1.6.4.2
next reply other threads:[~2010-01-17 12:03 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-01-17 12:03 Rafał Miłecki [this message]
2010-01-17 16:37 ` [PATCH 2/7] b43: N-PHY: implement TX PHY cleanup and setup Gábor Stefanik
2010-01-17 16:41 ` Michael Buesch
2010-01-17 16:44 ` Gábor Stefanik
2010-01-17 16:48 ` Rafał Miłecki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=op.u6oef6cl9lhzdc@linux-g0th.site \
--to=zajec5@gmail.com \
--cc=bcm43xx-dev@lists.berlios.de \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox