* Warnings when booting rc5 on a mpc83xx based board
@ 2007-01-16 17:20 Joakim Tjernlund
2007-01-16 19:43 ` Kumar Gala
` (2 more replies)
0 siblings, 3 replies; 10+ messages in thread
From: Joakim Tjernlund @ 2007-01-16 17:20 UTC (permalink / raw)
To: 'linuxppc-dev Development'
after upgrading to rc5 I get this:
IPIC (128 IRQ sources) at fdefd700
QEIC (64 IRQ sources) at fdefc080
PID hash table entries: 512 (order: 9, 2048 bytes)
------------[ cut here ]------------
Badness at c00f4278 [verbose debug info unavailable]
Call Trace:
[C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
[C0249DF0] [C00F2158] report_bug+0x84/0xac
[C0249E00] [C000DD28] program_check_exception+0xe0/0x538
[C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
--- Exception: 700 at kref_get+0xc/0x24
LR = of_node_get+0x20/0x38
[C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
[C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
[C0249F30] [C02198A0] get_freq+0x2c/0x80
[C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
[C0249F70] [C0219E5C] time_init+0x48c/0x530
[C0249FD0] [C02135F4] start_kernel+0x120/0x250
[C0249FF0] [00003438] 0x3438
------------[ cut here ]------------
Badness at c00f4278 [verbose debug info unavailable]
Call Trace:
[C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
[C0249DF0] [C00F2158] report_bug+0x84/0xac
[C0249E00] [C000DD28] program_check_exception+0xe0/0x538
[C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
--- Exception: 700 at kref_get+0xc/0x24
LR = of_node_get+0x20/0x38
[C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
[C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
[C0249F30] [C02198A0] get_freq+0x2c/0x80
[C0249F50] [C021999C] generic_calibrate_decr+0xa8/0xdc
[C0249F70] [C0219E5C] time_init+0x48c/0x530
[C0249FD0] [C02135F4] start_kernel+0x120/0x250
[C0249FF0] [00003438] 0x3438
------------[ cut here ]------------
Badness at c00f4278 [verbose debug info unavailable]
Call Trace:
[C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
[C0249DF0] [C00F2158] report_bug+0x84/0xac
[C0249E00] [C000DD28] program_check_exception+0xe0/0x538
[C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
--- Exception: 700 at kref_get+0xc/0x24
LR = of_node_get+0x20/0x38
[C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
[C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
[C0249F30] [C02198A0] get_freq+0x2c/0x80
[C0249F50] [C021996C] generic_calibrate_decr+0x78/0xdc
[C0249F70] [C0219E5C] time_init+0x48c/0x530
[C0249FD0] [C02135F4] start_kernel+0x120/0x250
[C0249FF0] [00003438] 0x3438
------------[ cut here ]------------
Badness at c00f4278 [verbose debug info unavailable]
Call Trace:
[C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
[C0249DF0] [C00F2158] report_bug+0x84/0xac
[C0249E00] [C000DD28] program_check_exception+0xe0/0x538
[C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
--- Exception: 700 at kref_get+0xc/0x24
LR = of_node_get+0x20/0x38
[C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
[C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
[C0249F30] [C02198A0] get_freq+0x2c/0x80
[C0249F50] [C02199B8] generic_calibrate_decr+0xc4/0xdc
[C0249F70] [C0219E5C] time_init+0x48c/0x530
[C0249FD0] [C02135F4] start_kernel+0x120/0x250
[C0249FF0] [00003438] 0x3438
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
and this:
Memory: 127272k/131072k available (2252k kernel code, 3636k reserved, 84k data, 95k bs
s, 128k init)
Mount-cache hash table entries: 512
------------[ cut here ]------------
Badness at c00f4278 [verbose debug info unavailable]
Call Trace:
[C0249E00] [C00085BC] show_stack+0x48/0x194 (unreliable)
[C0249E30] [C00F2158] report_bug+0x84/0xac
[C0249E40] [C000DD28] program_check_exception+0xe0/0x538
[C0249E80] [C000F78C] ret_from_except_full+0x0/0x4c
--- Exception: 700 at kref_get+0xc/0x24
LR = of_node_get+0x20/0x38
[C0249F40] [C00F2CA8] idr_get_new+0x1c/0x78 (unreliable)
[C0249F50] [C000CB0C] of_get_next_child+0x34/0x9c
[C0249F70] [C009556C] proc_device_tree_add_node+0x4c/0x144
[C0249F90] [C0095560] proc_device_tree_add_node+0x40/0x144
[C0249FB0] [C00956D8] proc_device_tree_init+0x74/0x90
[C0249FC0] [C0224630] proc_root_init+0x11c/0x138
[C0249FD0] [C02136B4] start_kernel+0x1e0/0x250
[C0249FF0] [00003438] 0x3438
NET: Registered protocol family 16
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 17:20 Warnings when booting rc5 on a mpc83xx based board Joakim Tjernlund
@ 2007-01-16 19:43 ` Kumar Gala
2007-01-16 19:55 ` Joakim Tjernlund
2007-01-16 20:11 ` Nathan Lynch
2007-01-17 6:09 ` Li Yang-r58472
2 siblings, 1 reply; 10+ messages in thread
From: Kumar Gala @ 2007-01-16 19:43 UTC (permalink / raw)
To: joakim.tjernlund; +Cc: 'linuxppc-dev Development'
Not seeing this on a 2.6.20-rc5 boot of MPC8349. Any special config
options on?
- k
On Jan 16, 2007, at 11:20 AM, Joakim Tjernlund wrote:
> after upgrading to rc5 I get this:
>
> IPIC (128 IRQ sources) at fdefd700
> QEIC (64 IRQ sources) at fdefc080
> PID hash table entries: 512 (order: 9, 2048 bytes)
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021999C] generic_calibrate_decr+0xa8/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021996C] generic_calibrate_decr+0x78/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C02199B8] generic_calibrate_decr+0xc4/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
>
>
> and this:
>
> Memory: 127272k/131072k available (2252k kernel code, 3636k
> reserved, 84k data, 95k bs
> s, 128k init)
> Mount-cache hash table entries: 512
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249E00] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249E30] [C00F2158] report_bug+0x84/0xac
> [C0249E40] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E80] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F40] [C00F2CA8] idr_get_new+0x1c/0x78 (unreliable)
> [C0249F50] [C000CB0C] of_get_next_child+0x34/0x9c
> [C0249F70] [C009556C] proc_device_tree_add_node+0x4c/0x144
> [C0249F90] [C0095560] proc_device_tree_add_node+0x40/0x144
> [C0249FB0] [C00956D8] proc_device_tree_init+0x74/0x90
> [C0249FC0] [C0224630] proc_root_init+0x11c/0x138
> [C0249FD0] [C02136B4] start_kernel+0x1e0/0x250
> [C0249FF0] [00003438] 0x3438
> NET: Registered protocol family 16
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 19:43 ` Kumar Gala
@ 2007-01-16 19:55 ` Joakim Tjernlund
0 siblings, 0 replies; 10+ messages in thread
From: Joakim Tjernlund @ 2007-01-16 19:55 UTC (permalink / raw)
To: Kumar Gala; +Cc: 'linuxppc-dev Development'
[-- Attachment #1: Type: text/plain, Size: 4846 bytes --]
Don't think so, config attached.
On Tue, 2007-01-16 at 13:43 -0600, Kumar Gala wrote:
> Not seeing this on a 2.6.20-rc5 boot of MPC8349. Any special config
> options on?
>
> - k
>
> On Jan 16, 2007, at 11:20 AM, Joakim Tjernlund wrote:
>
> > after upgrading to rc5 I get this:
> >
> > IPIC (128 IRQ sources) at fdefd700
> > QEIC (64 IRQ sources) at fdefc080
> > PID hash table entries: 512 (order: 9, 2048 bytes)
> > ------------[ cut here ]------------
> > Badness at c00f4278 [verbose debug info unavailable]
> > Call Trace:
> > [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> > [C0249DF0] [C00F2158] report_bug+0x84/0xac
> > [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> > [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> > --- Exception: 700 at kref_get+0xc/0x24
> > LR = of_node_get+0x20/0x38
> > [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
> > [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> > [C0249F30] [C02198A0] get_freq+0x2c/0x80
> > [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
> > [C0249F70] [C0219E5C] time_init+0x48c/0x530
> > [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> > [C0249FF0] [00003438] 0x3438
> > ------------[ cut here ]------------
> > Badness at c00f4278 [verbose debug info unavailable]
> > Call Trace:
> > [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> > [C0249DF0] [C00F2158] report_bug+0x84/0xac
> > [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> > [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> > --- Exception: 700 at kref_get+0xc/0x24
> > LR = of_node_get+0x20/0x38
> > [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> > [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> > [C0249F30] [C02198A0] get_freq+0x2c/0x80
> > [C0249F50] [C021999C] generic_calibrate_decr+0xa8/0xdc
> > [C0249F70] [C0219E5C] time_init+0x48c/0x530
> > [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> > [C0249FF0] [00003438] 0x3438
> > ------------[ cut here ]------------
> > Badness at c00f4278 [verbose debug info unavailable]
> > Call Trace:
> > [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> > [C0249DF0] [C00F2158] report_bug+0x84/0xac
> > [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> > [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> > --- Exception: 700 at kref_get+0xc/0x24
> > LR = of_node_get+0x20/0x38
> > [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> > [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> > [C0249F30] [C02198A0] get_freq+0x2c/0x80
> > [C0249F50] [C021996C] generic_calibrate_decr+0x78/0xdc
> > [C0249F70] [C0219E5C] time_init+0x48c/0x530
> > [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> > [C0249FF0] [00003438] 0x3438
> > ------------[ cut here ]------------
> > Badness at c00f4278 [verbose debug info unavailable]
> > Call Trace:
> > [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> > [C0249DF0] [C00F2158] report_bug+0x84/0xac
> > [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> > [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> > --- Exception: 700 at kref_get+0xc/0x24
> > LR = of_node_get+0x20/0x38
> > [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> > [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> > [C0249F30] [C02198A0] get_freq+0x2c/0x80
> > [C0249F50] [C02199B8] generic_calibrate_decr+0xc4/0xdc
> > [C0249F70] [C0219E5C] time_init+0x48c/0x530
> > [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> > [C0249FF0] [00003438] 0x3438
> > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> >
> >
> > and this:
> >
> > Memory: 127272k/131072k available (2252k kernel code, 3636k
> > reserved, 84k data, 95k bs
> > s, 128k init)
> > Mount-cache hash table entries: 512
> > ------------[ cut here ]------------
> > Badness at c00f4278 [verbose debug info unavailable]
> > Call Trace:
> > [C0249E00] [C00085BC] show_stack+0x48/0x194 (unreliable)
> > [C0249E30] [C00F2158] report_bug+0x84/0xac
> > [C0249E40] [C000DD28] program_check_exception+0xe0/0x538
> > [C0249E80] [C000F78C] ret_from_except_full+0x0/0x4c
> > --- Exception: 700 at kref_get+0xc/0x24
> > LR = of_node_get+0x20/0x38
> > [C0249F40] [C00F2CA8] idr_get_new+0x1c/0x78 (unreliable)
> > [C0249F50] [C000CB0C] of_get_next_child+0x34/0x9c
> > [C0249F70] [C009556C] proc_device_tree_add_node+0x4c/0x144
> > [C0249F90] [C0095560] proc_device_tree_add_node+0x40/0x144
> > [C0249FB0] [C00956D8] proc_device_tree_init+0x74/0x90
> > [C0249FC0] [C0224630] proc_root_init+0x11c/0x138
> > [C0249FD0] [C02136B4] start_kernel+0x1e0/0x250
> > [C0249FF0] [00003438] 0x3438
> > NET: Registered protocol family 16
> >
> > _______________________________________________
> > Linuxppc-dev mailing list
> > Linuxppc-dev@ozlabs.org
> > https://ozlabs.org/mailman/listinfo/linuxppc-dev
>
>
>
[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 23976 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.20-rc5
# Tue Jan 16 17:04:58 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_NVRAM=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_PPC_UDBG_16550=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFAULT_UIMAGE=y
#
# Processor support
#
# CONFIG_CLASSIC32 is not set
# CONFIG_PPC_82xx is not set
CONFIG_PPC_83xx=y
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_86xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_8xx is not set
# CONFIG_E200 is not set
CONFIG_6xx=y
CONFIG_83xx=y
CONFIG_PPC_FPU=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
# CONFIG_SMP is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
# CONFIG_EPOLL is not set
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Loadable module support
#
# CONFIG_MODULES is not set
#
# Block layer
#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
CONFIG_QUICC_ENGINE=y
CONFIG_PPC_GEN550=y
# CONFIG_WANT_EARLY_SERIAL is not set
#
# Platform support
#
# CONFIG_MPC832x_MDS is not set
CONFIG_TMCUTU=y
# CONFIG_MPC834x_SYS is not set
# CONFIG_MPC834x_ITX is not set
# CONFIG_MPC8360E_PB is not set
CONFIG_PPC_MPC832x=y
# CONFIG_MPIC is not set
#
# Kernel options
#
# CONFIG_HIGHMEM is not set
CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
# CONFIG_SECCOMP is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_GENERIC_ISA_DMA=y
# CONFIG_MPIC_WEIRD is not set
# CONFIG_PPC_I8259 is not set
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_FSL_SOC=y
# CONFIG_PCI is not set
# CONFIG_PCI_DOMAINS is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_BOOT_LOAD=0x00800000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
CONFIG_MTD_CFI_ADV_OPTIONS=y
CONFIG_MTD_CFI_NOSWAP=y
# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
CONFIG_MTD_CFI_GEOMETRY=y
# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
CONFIG_MTD_MAP_BANK_WIDTH_2=y
# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
# CONFIG_MTD_CFI_I2 is not set
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_OTP is not set
CONFIG_MTD_CFI_INTELEXT=y
# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
#
CONFIG_MTD_COMPLEX_MAPPINGS=y
# CONFIG_MTD_PHYSMAP is not set
CONFIG_MTD_TMCUTU=y
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
#
# NAND Flash Device Drivers
#
# CONFIG_MTD_NAND is not set
#
# OneNAND Flash Device Drivers
#
# CONFIG_MTD_ONENAND is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
# CONFIG_TIFM_CORE is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
# CONFIG_BLK_DEV_SD is not set
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_DEBUG is not set
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
#
# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Macintosh device drivers
#
# CONFIG_MAC_EMUMOUSEBTN is not set
# CONFIG_WINDFARM is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# PHY device support
#
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_GIANFAR is not set
CONFIG_UCC_GETH=y
# CONFIG_UGETH_NAPI is not set
# CONFIG_UGETH_MAGIC_PACKET is not set
# CONFIG_UGETH_FILTERING is not set
# CONFIG_UGETH_TX_ON_DEMOND is not set
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
CONFIG_PPP=y
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
# CONFIG_PPP_ASYNC is not set
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPP_MPPE is not set
CONFIG_PPPOE=y
# CONFIG_SLIP is not set
CONFIG_SLHC=y
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
# CONFIG_VT is not set
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_83xx_WDT=y
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
CONFIG_I2C_MPC=y
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_M41T00 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
CONFIG_SPI=y
CONFIG_SPI_DEBUG=y
CONFIG_SPI_MASTER=y
#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=y
CONFIG_SPI_MPC83xx=y
#
# SPI Protocol Masters
#
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# HID Devices
#
# CONFIG_HID is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
# CONFIG_USB_OTG is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# USB Gadget Support
#
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DEBUG_FILES=y
CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET_NET2280 is not set
# CONFIG_USB_GADGET_PXA2XX is not set
# CONFIG_USB_GADGET_GOKU is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
CONFIG_USB_GADGET_QE=y
CONFIG_USB_QE=y
# CONFIG_USB_GADGET_AT91 is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
# CONFIG_USB_GADGET_DUALSPEED is not set
# CONFIG_USB_ZERO is not set
CONFIG_USB_ETH=y
# CONFIG_USB_ETH_RNDIS is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FILE_STORAGE is not set
# CONFIG_USB_G_SERIAL is not set
# CONFIG_USB_MIDI_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# LED devices
#
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
#
# LED drivers
#
#
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
#
# InfiniBand support
#
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# Real Time Clock
#
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
#
# RTC drivers
#
# CONFIG_RTC_DRV_X1205 is not set
CONFIG_RTC_DRV_DS1307=y
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set
#
# DMA Clients
#
#
# DMA Devices
#
#
# Virtualization
#
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_EXT4DEV_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
# CONFIG_JFFS2_FS_WRITEBUFFER is not set
CONFIG_JFFS2_SUMMARY=y
# CONFIG_JFFS2_FS_XATTR is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_MSDOS_PARTITION is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# Distributed Lock Manager
#
# CONFIG_DLM is not set
#
# QE Options
#
CONFIG_UCC_SLOW=y
CONFIG_UCC_FAST=y
CONFIG_UCC=y
#
# Library routines
#
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
CONFIG_IOMAP_COPY=y
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_DEBUGGER is not set
CONFIG_BDI_SWITCH=y
# CONFIG_BOOTX_TEXT is not set
# CONFIG_SERIAL_TEXT_DEBUG is not set
# CONFIG_PPC_EARLY_DEBUG is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_MANAGER=y
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_LRW is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
#
# Hardware crypto devices
#
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 17:20 Warnings when booting rc5 on a mpc83xx based board Joakim Tjernlund
2007-01-16 19:43 ` Kumar Gala
@ 2007-01-16 20:11 ` Nathan Lynch
2007-01-16 20:36 ` Kumar Gala
2007-01-17 6:09 ` Li Yang-r58472
2 siblings, 1 reply; 10+ messages in thread
From: Nathan Lynch @ 2007-01-16 20:11 UTC (permalink / raw)
To: Joakim Tjernlund; +Cc: 'linuxppc-dev Development'
Joakim Tjernlund wrote:
> after upgrading to rc5 I get this:
>
> IPIC (128 IRQ sources) at fdefd700
> QEIC (64 IRQ sources) at fdefc080
> PID hash table entries: 512 (order: 9, 2048 bytes)
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR = of_node_get+0x20/0x38
> [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
Looks like it could be an unbalanced of_node_put causing a node's
refcount to underflow, probably the root node. The warning in
kref_get has unearthed a couple of these recently, see
http://patchwork.ozlabs.org/linuxppc/patch?id=8840
for example.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 20:11 ` Nathan Lynch
@ 2007-01-16 20:36 ` Kumar Gala
2007-01-16 20:51 ` Kumar Gala
0 siblings, 1 reply; 10+ messages in thread
From: Kumar Gala @ 2007-01-16 20:36 UTC (permalink / raw)
To: Joakim Tjernlund; +Cc: linuxppc-dev Development
On Jan 16, 2007, at 2:11 PM, Nathan Lynch wrote:
> Joakim Tjernlund wrote:
>> after upgrading to rc5 I get this:
>>
>> IPIC (128 IRQ sources) at fdefd700
>> QEIC (64 IRQ sources) at fdefc080
>> PID hash table entries: 512 (order: 9, 2048 bytes)
>> ------------[ cut here ]------------
>> Badness at c00f4278 [verbose debug info unavailable]
>> Call Trace:
>> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
>> [C0249DF0] [C00F2158] report_bug+0x84/0xac
>> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
>> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
>> --- Exception: 700 at kref_get+0xc/0x24
>> LR = of_node_get+0x20/0x38
>> [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
>> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
>> [C0249F30] [C02198A0] get_freq+0x2c/0x80
>> [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
>> [C0249F70] [C0219E5C] time_init+0x48c/0x530
>> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
>> [C0249FF0] [00003438] 0x3438
>
> Looks like it could be an unbalanced of_node_put causing a node's
> refcount to underflow, probably the root node. The warning in
> kref_get has unearthed a couple of these recently, see
>
> http://patchwork.ozlabs.org/linuxppc/patch?id=8840
>
> for example.
Joakim,
In your board code do you having something like:
np = of_find_node_by_type(NULL, "qeic");
if (!np)
return;
qe_ic_init(np, 0);
of_node_put(np);
in _init_IRQ?
if so remove the of_node_put() after qe_ic_init() and see if the
issue still exists.
- k
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 20:36 ` Kumar Gala
@ 2007-01-16 20:51 ` Kumar Gala
0 siblings, 0 replies; 10+ messages in thread
From: Kumar Gala @ 2007-01-16 20:51 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev Development
On Jan 16, 2007, at 2:36 PM, Kumar Gala wrote:
>
> On Jan 16, 2007, at 2:11 PM, Nathan Lynch wrote:
>
>> Joakim Tjernlund wrote:
>>> after upgrading to rc5 I get this:
>>>
>>> IPIC (128 IRQ sources) at fdefd700
>>> QEIC (64 IRQ sources) at fdefc080
>>> PID hash table entries: 512 (order: 9, 2048 bytes)
>>> ------------[ cut here ]------------
>>> Badness at c00f4278 [verbose debug info unavailable]
>>> Call Trace:
>>> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
>>> [C0249DF0] [C00F2158] report_bug+0x84/0xac
>>> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
>>> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
>>> --- Exception: 700 at kref_get+0xc/0x24
>>> LR = of_node_get+0x20/0x38
>>> [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
>>> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
>>> [C0249F30] [C02198A0] get_freq+0x2c/0x80
>>> [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
>>> [C0249F70] [C0219E5C] time_init+0x48c/0x530
>>> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
>>> [C0249FF0] [00003438] 0x3438
>>
>> Looks like it could be an unbalanced of_node_put causing a node's
>> refcount to underflow, probably the root node. The warning in
>> kref_get has unearthed a couple of these recently, see
>>
>> http://patchwork.ozlabs.org/linuxppc/patch?id=8840
>>
>> for example.
>
> Joakim,
>
> In your board code do you having something like:
>
> np = of_find_node_by_type(NULL, "qeic");
> if (!np)
> return;
>
> qe_ic_init(np, 0);
> of_node_put(np);
>
> in _init_IRQ?
>
> if so remove the of_node_put() after qe_ic_init() and see if the
> issue still exists.
If this ends up being the issue we'll change qe_ic_init to stop doing
the of_node_put() and change ipic_init() as well. But lets first
validate that this is the cause.
- k
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Warnings when booting rc5 on a mpc83xx based board
2007-01-16 17:20 Warnings when booting rc5 on a mpc83xx based board Joakim Tjernlund
2007-01-16 19:43 ` Kumar Gala
2007-01-16 20:11 ` Nathan Lynch
@ 2007-01-17 6:09 ` Li Yang-r58472
2 siblings, 0 replies; 10+ messages in thread
From: Li Yang-r58472 @ 2007-01-17 6:09 UTC (permalink / raw)
To: joakim.tjernlund, linuxppc-dev Development
Please try:
--- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
@@ -103,7 +103,7 @@ static void __init mpc832x_sys_setup_arch(void)
#ifdef CONFIG_QUICC_ENGINE
qe_reset();
- if ((np =3D of_find_node_by_name(np, "par_io")) !=3D NULL) {
+ if ((np =3D of_find_node_by_name(NULL, "par_io")) !=3D NULL) {
par_io_init(np);
of_node_put(np);
- Leo
> -----Original Message-----
> From: linuxppc-dev-bounces+leoli=3Dfreescale.com@ozlabs.org
> [mailto:linuxppc-dev-bounces+leoli=3Dfreescale.com@ozlabs.org] On =
Behalf
Of Joakim
> Tjernlund
> Sent: Wednesday, January 17, 2007 1:21 AM
> To: 'linuxppc-dev Development'
> Subject: Warnings when booting rc5 on a mpc83xx based board
>=20
> after upgrading to rc5 I get this:
>=20
> IPIC (128 IRQ sources) at fdefd700
> QEIC (64 IRQ sources) at fdefc080
> PID hash table entries: 512 (order: 9, 2048 bytes)
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR =3D of_node_get+0x20/0x38
> [C0249F00] [FFFFFFFF] 0xffffffff (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021992C] generic_calibrate_decr+0x38/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR =3D of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021999C] generic_calibrate_decr+0xa8/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR =3D of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C021996C] generic_calibrate_decr+0x78/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249DC0] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249DF0] [C00F2158] report_bug+0x84/0xac
> [C0249E00] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E40] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR =3D of_node_get+0x20/0x38
> [C0249F00] [C7FFEB94] 0xc7ffeb94 (unreliable)
> [C0249F10] [C000CCA0] of_find_node_by_type+0x8c/0xd0
> [C0249F30] [C02198A0] get_freq+0x2c/0x80
> [C0249F50] [C02199B8] generic_calibrate_decr+0xc4/0xdc
> [C0249F70] [C0219E5C] time_init+0x48c/0x530
> [C0249FD0] [C02135F4] start_kernel+0x120/0x250
> [C0249FF0] [00003438] 0x3438
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
>=20
>=20
> and this:
>=20
> Memory: 127272k/131072k available (2252k kernel code, 3636k reserved,
84k data,
> 95k bs
> s, 128k init)
> Mount-cache hash table entries: 512
> ------------[ cut here ]------------
> Badness at c00f4278 [verbose debug info unavailable]
> Call Trace:
> [C0249E00] [C00085BC] show_stack+0x48/0x194 (unreliable)
> [C0249E30] [C00F2158] report_bug+0x84/0xac
> [C0249E40] [C000DD28] program_check_exception+0xe0/0x538
> [C0249E80] [C000F78C] ret_from_except_full+0x0/0x4c
> --- Exception: 700 at kref_get+0xc/0x24
> LR =3D of_node_get+0x20/0x38
> [C0249F40] [C00F2CA8] idr_get_new+0x1c/0x78 (unreliable)
> [C0249F50] [C000CB0C] of_get_next_child+0x34/0x9c
> [C0249F70] [C009556C] proc_device_tree_add_node+0x4c/0x144
> [C0249F90] [C0095560] proc_device_tree_add_node+0x40/0x144
> [C0249FB0] [C00956D8] proc_device_tree_init+0x74/0x90
> [C0249FC0] [C0224630] proc_root_init+0x11c/0x138
> [C0249FD0] [C02136B4] start_kernel+0x1e0/0x250
> [C0249FF0] [00003438] 0x3438
> NET: Registered protocol family 16
>=20
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Warnings when booting rc5 on a mpc83xx based board
@ 2007-01-17 7:57 Joakim Tjernlund
2007-01-17 8:00 ` Liu Dave-r63238
0 siblings, 1 reply; 10+ messages in thread
From: Joakim Tjernlund @ 2007-01-17 7:57 UTC (permalink / raw)
To: Li Yang-r58472, linuxppc-dev Development
> -----Original Message-----
> From: Li Yang-r58472 [mailto:LeoLi@freescale.com]=20
> Sent: 17 January 2007 07:10
> To: Joakim Tjernlund; linuxppc-dev Development
> Subject: RE: Warnings when booting rc5 on a mpc83xx based board
>=20
> Please try:
>=20
> --- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
> +++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
> @@ -103,7 +103,7 @@ static void __init mpc832x_sys_setup_arch(void)
> #ifdef CONFIG_QUICC_ENGINE
> qe_reset();
>=20
> - if ((np =3D of_find_node_by_name(np, "par_io")) !=3D NULL) {
> + if ((np =3D of_find_node_by_name(NULL, "par_io")) !=3D NULL) {
> par_io_init(np);
> of_node_put(np);
>=20
> - Leo
Thanks, this did fix the problem.
Kumar, FYI your proposal had no effect.
Jocke
^ permalink raw reply [flat|nested] 10+ messages in thread* RE: Warnings when booting rc5 on a mpc83xx based board
2007-01-17 7:57 Joakim Tjernlund
@ 2007-01-17 8:00 ` Liu Dave-r63238
2007-01-17 8:44 ` Grant Likely
0 siblings, 1 reply; 10+ messages in thread
From: Liu Dave-r63238 @ 2007-01-17 8:00 UTC (permalink / raw)
To: Joakim Tjernlund, Li Yang-r58472, linuxppc-dev Development
When the OF will be stable? The OF is really painful for embedded
system.
> -----Original Message-----
> From: linuxppc-dev-bounces+daveliu=3Dfreescale.com@ozlabs.org=20
> [mailto:linuxppc-dev-bounces+daveliu=3Dfreescale.com@ozlabs.org]
> On Behalf Of Joakim Tjernlund
> Sent: 2007?1?17? 3:58 PM
> To: Li Yang-r58472; linuxppc-dev Development
> Subject: RE: Warnings when booting rc5 on a mpc83xx based board
>=20
> > -----Original Message-----
> > From: Li Yang-r58472 [mailto:LeoLi@freescale.com]
> > Sent: 17 January 2007 07:10
> > To: Joakim Tjernlund; linuxppc-dev Development
> > Subject: RE: Warnings when booting rc5 on a mpc83xx based board
> >=20
> > Please try:
> >=20
> > --- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
> > +++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
> > @@ -103,7 +103,7 @@ static void __init=20
> mpc832x_sys_setup_arch(void) =20
> > #ifdef CONFIG_QUICC_ENGINE
> > qe_reset();
> >=20
> > - if ((np =3D of_find_node_by_name(np, "par_io")) !=3D NULL) {
> > + if ((np =3D of_find_node_by_name(NULL, "par_io")) !=3D NULL) =
{
> > par_io_init(np);
> > of_node_put(np);
> >=20
> > - Leo
>=20
> Thanks, this did fix the problem.
>=20
> Kumar, FYI your proposal had no effect.
>=20
> Jocke
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
>=20
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: Warnings when booting rc5 on a mpc83xx based board
2007-01-17 8:00 ` Liu Dave-r63238
@ 2007-01-17 8:44 ` Grant Likely
0 siblings, 0 replies; 10+ messages in thread
From: Grant Likely @ 2007-01-17 8:44 UTC (permalink / raw)
To: Liu Dave-r63238; +Cc: linuxppc-dev Development
On 1/17/07, Liu Dave-r63238 <DaveLiu@freescale.com> wrote:
> The OF is really painful for embedded system.
For the record; I have to disagree. I find the device tree cleans up
and makes more maintainable a lot of my code. It gets rid of a lot of
my crazy-ass hacks for using different SoC configurations on different
boards.
Cheers,
g.
--
Grant Likely, B.Sc. P.Eng.
Secret Lab Technologies Ltd.
grant.likely@secretlab.ca
(403) 399-0195
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2007-01-17 8:44 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-01-16 17:20 Warnings when booting rc5 on a mpc83xx based board Joakim Tjernlund
2007-01-16 19:43 ` Kumar Gala
2007-01-16 19:55 ` Joakim Tjernlund
2007-01-16 20:11 ` Nathan Lynch
2007-01-16 20:36 ` Kumar Gala
2007-01-16 20:51 ` Kumar Gala
2007-01-17 6:09 ` Li Yang-r58472
-- strict thread matches above, loose matches on Subject: below --
2007-01-17 7:57 Joakim Tjernlund
2007-01-17 8:00 ` Liu Dave-r63238
2007-01-17 8:44 ` Grant Likely
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox