* Re: Fixed PHY and MPC832x based boards don't work
2007-05-13 20:36 ` Vitaly Bordug
@ 2007-05-13 22:25 ` Joakim Tjernlund
2007-05-15 11:40 ` Joakim Tjernlund
0 siblings, 1 reply; 4+ messages in thread
From: Joakim Tjernlund @ 2007-05-13 22:25 UTC (permalink / raw)
To: Vitaly Bordug; +Cc: linuxppc-dev
On Mon, 2007-05-14 at 00:36 +0400, Vitaly Bordug wrote:
> On Sun, 13 May 2007 16:39:30 +0200
> Joakim Tjernlund wrote:
>
> > Trying to make the Fixed PHY work under my 832x based board on current
> > linus tree without success. Earlier kernels with custom PHY code for
> > ucc_geth work without any special tricks.
> >
> > If I enable the FIXED_MII_100_FDX option I get:
> > ls bus/mdio_bus/devices/
> > fixed@100:1@
> >
> > but ucc_geth wants its PHYs under
> > ls -l bus/of_platform/devices/*phy*
> > lrwxrwxrwx 1 root root 0 May 12 17:32
> > bus/of_platform/devices/ethernet-p hy.1
> > -> ../../../devices/e0100000.qe/e0102320.mdio/ethernet-phy.1/
> > lrwxrwxrwx 1 root root 0 May 12 17:32
> > bus/of_platform/devices/ethernet-p hy.3
> > -> ../../../devices/e0100000.qe/e0102320.mdio/ethernet-phy.3/
> > lrwxrwxrwx 1 root root 0 May 12 17:32
> > bus/of_platform/devices/fixed-phy. 2
> > -> ../../../devices/e0100000.qe/e0102320.mdio/fixed-phy.2/ These are
> > 3 PHYs I just added in the DTS tree:
> >
> > mdio@2320 {
> > #address-cells = <1>;
> > #size-cells = <0>;
> > reg = <2320 18>;
> > device_type = "mdio";
> > compatible = "ucc_geth_phy";
> >
> > phy1: ethernet-phy@18 {
> > linux,phandle = <212000>;
> > reg = <18>; // 24
> > device_type = "ethernet-phy";
> > interface = <3>; //ENET_100_MII
> > };
> > phy2: fixed-phy@64 {
> > linux,phandle = <212001>;
> > reg = <d#100>;
> > device_type = "ethernet-phy";
> > };
> > phy3: ethernet-phy@19 {
> > linux,phandle = <212002>;
> > interrupt-parent = <700>;
> > interrupts = <12 2>;
> > reg = <19>; // 25
> > device_type = "ethernet-phy";
> > interface = <3>; //ENET_100_MII
> > };
> > };
> >
> > How do I add a fixed PHY so that ucc_geth finds it?
> >
> well I guess ucc stuff follows gianfar trend in mdio bus specification for the phy.
> So, it would look like %d:%d or something like that.
>
> Can you please dump the whole dts here?
Sure, it look pretty much like the 832x_mds
phy2 is my experiment to get hold of the fixed phy, but the others should also be converted into a fixed phy. Here goes my DTS:
/ {
model = "TMCUTU";
compatible = "MPC83xx";
#address-cells = <1>;
#size-cells = <1>;
linux,phandle = <100>;
board {
bd_version = <1>;
slot_pos = <0>;
board_type = <0>;
sys_type = <0>;
sys_mode = <0>;
sys_rev = <0>;
subrack_id = <0>;
power_on_start = <0>;
target = <0>;
bi_r_version = "1234X1234X1234X1234X1234X1234X1234X";
enable_usb = <0>;
};
flash@f8000000 {
device_type = "rom";
compatible = "direct-mapped";
probe-type = "CFI";
reg = <f8000000 08000000>;
bank-width = <2>;
partitions = <00000000 00010000 /* HRCW */
00010000 00008000 /* env0 */
00018000 00008000 /* env1 */
00020000 00040000 /* u-boot0 */
00060000 00040000 /* u-boot1 */
000a0000 001e0000 /* kernel */
00280000 07d60000 /* JFFS2 */
>;
partition-names = "HRCW\0env0\0env1\0u-boot0\0u-boot1\0kernel\0JFFS2";
};
cpus {
#cpus = <1>;
#address-cells = <1>;
#size-cells = <0>;
linux,phandle = <200>;
PowerPC,8321@0 {
device_type = "cpu";
reg = <0>;
d-cache-line-size = <20>; // 32 bytes
i-cache-line-size = <20>; // 32 bytes
d-cache-size = <8000>; // L1, 32K
i-cache-size = <8000>; // L1, 32K
timebase-frequency = <0>; // Estimated by linux
bus-frequency = <0>;
clock-frequency = <0>;
32-bit;
linux,phandle = <201>;
// linux,boot-cpu;
};
};
memory {
device_type = "memory";
linux,phandle = <300>;
reg = <00000000 10000000>; //256 MB
//reg = <00000000 8000000>; //128 MB
};
soc8321@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
ranges = <0 e0000000 00100000>;
reg = <e0000000 00000200>;
bus-frequency = <0>; //Set by boot
/*
wdt@200 {
device_type = "watchdog";
compatible = "mpc83xx_wdt";
reg = <200 100>;
};
*/
i2c@3000 {
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = <700>;
dfsrr;
};
/*
i2c@3100 {
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
interrupts = <f 8>;
interrupt-parent = <700>;
dfsrr;
};
*/
serial@4500 {
device_type = "serial";
compatible = "ns16550";
reg = <4500 100>;
clock-frequency = <0>; //Set by boot
interrupts = <9 8>;
interrupt-parent = <700>;
};
/*
serial@4600 {
device_type = "serial";
compatible = "ns16550";
reg = <4600 100>;
clock-frequency = <FBC5200>;
interrupts = <a 8>;
interrupt-parent = <700>;
};
*/
/*
crypto@30000 {
device_type = "crypto";
model = "SEC2";
compatible = "talitos";
reg = <30000 10000>;
interrupts = <b 8>;
interrupt-parent = <700>;
num-channels = <4>;
channel-fifo-len = <18>;
exec-units-mask = <0000007e>;
//desc mask is for rev1.x, we need runtime fixup for >=2.x
descriptor-types-mask = <01010ebf>;
};
*/
/*
pci@8500 {
linux,phandle = <8500>;
interrupt-map-mask = <f800 0 0 7>;
interrupt-map = <
// IDSEL 0x11 AD17
8800 0 0 1 700 14 8
8800 0 0 2 700 15 8
8800 0 0 3 700 16 8
8800 0 0 4 700 17 8
// IDSEL 0x12 AD18
9000 0 0 1 700 16 8
9000 0 0 2 700 17 8
9000 0 0 3 700 14 8
9000 0 0 4 700 15 8
// IDSEL 0x13 AD19
9800 0 0 1 700 17 8
9800 0 0 2 700 14 8
9800 0 0 3 700 15 8
9800 0 0 4 700 16 8
// IDSEL 0x15 AD21
a800 0 0 1 700 14 8
a800 0 0 2 700 15 8
a800 0 0 3 700 16 8
a800 0 0 4 700 17 8
// IDSEL 0x16 AD22
b000 0 0 1 700 17 8
b000 0 0 2 700 14 8
b000 0 0 3 700 15 8
b000 0 0 4 700 16 8
// IDSEL 0x17 AD23
b800 0 0 1 700 16 8
b800 0 0 2 700 17 8
b800 0 0 3 700 14 8
b800 0 0 4 700 15 8
// IDSEL 0x18 AD24
c000 0 0 1 700 15 8
c000 0 0 2 700 16 8
c000 0 0 3 700 17 8
c000 0 0 4 700 14 8>;
interrupt-parent = <700>;
interrupts = <42 8>;
bus-range = <0 0>;
ranges = <02000000 0 a0000000 90000000 0 10000000
42000000 0 80000000 80000000 0 10000000
01000000 0 00000000 d0000000 0 00100000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <8500 100>;
compatible = "83xx";
device_type = "pci";
};
*/
// IPIC
pic@700 {
linux,phandle = <700>;
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
reg = <700 100>;
built-in;
device_type = "ipic";
};
par_io@1400 {
reg = <1400 100>;
device_type = "par_io";
num-ports = <4>;
ucc_pin@02 {
linux,phandle = <140001>;
pio-map = <
// port pin dir open_drain assignment has_irq
3 4 3 0 2 0 // MDIO
3 5 1 0 2 0 // MDC
0 12 1 0 1 0 // TxD0, 18
0 13 1 0 1 0 // TxD1, 19
0 14 1 0 1 0 // TxD2, 20
0 15 1 0 1 0 // TxD3, 21
0 1b 1 0 1 0 // TxER, 27
0 1e 1 0 1 0 // TxEN, 30
3 16 2 0 1 0 // TxCLK->CLK4, 22
0 16 2 0 1 0 // RxD0, 22
0 17 2 0 1 0 // RxD1, 23
0 18 2 0 1 0 // RxD2, 24
0 19 2 0 1 0 // RxD3, 25
0 1a 2 0 1 0 // RxER, 26
0 1c 2 0 1 0 // RxDV, 28
3 17 2 0 1 0 // RxCLK->CLK3, 23
0 1d 2 0 1 0 // COL, 29
0 1f 2 0 1 0 // CRS, 31
>;
};
ucc_pin@03 {
linux,phandle = <140002>;
pio-map = <
1 0 1 0 1 0 // TxD0, 0
1 1 1 0 1 0 // TxD1, 1
1 2 1 0 1 0 // TxD2, 2
1 3 1 0 1 0 // TxD3, 3
1 9 1 0 1 0 // TxER, 9
1 c 1 0 1 0 // TxEN, 12
3 18 2 0 1 0 // TxCLK->CLK10, 24
1 4 2 0 1 0 // RxD0, 4
1 5 2 0 1 0 // RxD1, 5
1 6 2 0 1 0 // RxD2, 6
1 7 2 0 1 0 // RxD3, 7
1 8 2 0 1 0 // RxER, 8
1 a 2 0 1 0 // RxDV, 10
0 d 2 0 1 0 // RxCLK->CLK9, 13
1 b 2 0 1 0 // COL, 11
1 d 2 0 1 0 // CRS, 13
>; // MDC
};
ucc_pin@04 {
linux,phandle = <140003>;
pio-map = <
1 12 1 0 1 0 // TxD0, 18
1 13 1 0 1 0 // TxD1, 19
1 14 1 0 1 0 // TxD2, 20
1 15 1 0 1 0 // TxD3, 21
1 1b 1 0 1 0 // TxER, 27
1 1e 1 0 1 0 // TxEN, 30
3 6 2 0 1 0 // TxCLK->CLK8, 6
1 16 2 0 1 0 // RxD0, 22
1 17 2 0 1 0 // RxD1, 23
1 18 2 0 1 0 // RxD2, 24
1 19 2 0 1 0 // RxD3, 25
1 1a 2 0 1 0 // RxER, 26
1 1c 2 0 1 0 // RxDV, 28
3 1f 2 0 1 0 // RxCLK->CLK7, 31
1 1d 2 0 1 0 // COL, 29
1 1f 2 0 1 0 // CRS, 31
>; // MDC
};
};
};
// QE
qe@e0100000 {
#address-cells = <1>;
#size-cells = <1>;
//#interrupt-cells = <2>;
device_type = "qe";
model = "QE";
ranges = <0 e0100000 00100000>;
reg = <e0100000 480>;
brg-frequency = <0>; // set by boot
bus-frequency = <0>; // set by boot
muram@10000 {
device_type = "muram";
ranges = <0 00010000 00004000>;
data-only@0{
reg = <0 4000>;
};
};
spi@4c0 {
device_type = "spi";
compatible = "fsl_spi";
reg = <4c0 40>;
interrupts = <2>;
interrupt-parent = <80>;
mode = "cpu";
};
/*
spi@500 {
device_type = "spi";
compatible = "fsl_spi";
reg = <500 40>;
//interrupts = <81 0>;
interrupts = <1>;
interrupt-parent = <80>;
mode = "cpu";
};
*/
brg@640 {
device_type = "brg";
reg = <668 4>;
};
usb@6c0 {
device_type = "usb";
compatible = "qe_udc";
reg = <6c0 40 8B00 100>;
//reg_pram = <8B00 100>;
interrupts = <b>;
interrupt-parent = <80>;
mode = "slave";
};
ucc@3000 { //UCC2
device_type = "network";
compatible = "ucc_geth";
model = "UCC";
device-id = <2>;
reg = <3000 200>;
interrupts = <21>;
interrupt-parent = <80>;
mac-address = [ 00 04 9f 00 23 23 ];
rx-clock = <13>; //CLK3 19
tx-clock = <14>; //CLK4 20
phy-handle = <&phy1>;
phy-connection-type = "mii";
max-speed = <64>; // 100
pio-handle = <140001>;
};
ucc@2200 { //UCC3
device_type = "network";
compatible = "ucc_geth";
model = "UCC";
device-id = <3>;
reg = <2200 200>;
interrupts = <22>;
interrupt-parent = <80>;
mac-address = [ 00 11 22 33 44 55 ];
rx-clock = <19>; //CLK9, 25
tx-clock = <1a>; //CLK10, 26
phy-handle = <&phy2>;
phy-connection-type = "mii";
max-speed = <64>; // d#100
pio-handle = <140002>;
};
ucc@3200 { //UCC4
device_type = "network";
compatible = "ucc_geth";
model = "UCC";
device-id = <4>;
reg = <3200 200>;
interrupts = <23>;
interrupt-parent = <80>;
mac-address = [ 00 11 22 33 44 99 ];
rx-clock = <17>; //CLK7, 23
tx-clock = <18>; //CLK8, 24
phy-handle = <212002>;
phy-connection-type = "mii";
max-speed = <d#100>; //d#100
pio-handle = <140003>;
};
mdio@2320 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2320 18>;
device_type = "mdio";
compatible = "ucc_geth_phy";
phy1: ethernet-phy@18 {
linux,phandle = <212000>;
reg = <18>; // 24
device_type = "ethernet-phy";
interface = <3>; //ENET_100_MII
};
phy2: fixed-phy@64 {
linux,phandle = <212001>;
reg = <d#100>;
device_type = "ethernet-phy";
};
phy3: ethernet-phy@19 {
linux,phandle = <212002>;
interrupt-parent = <700>;
interrupts = <12 2>;
reg = <19>; // 25
device_type = "ethernet-phy";
interface = <3>; //ENET_100_MII
};
};
qeic@80 {
linux,phandle = <80>;
interrupt-controller;
device_type = "qeic";
#address-cells = <0>;
#interrupt-cells = <1>;
reg = <80 80>;
built-in;
big-endian;
interrupts = <20 8 21 8>; //high:32 low:33
interrupt-parent = <700>;
};
};
};
^ permalink raw reply [flat|nested] 4+ messages in thread