SCC1 as serial console

SCC1 as serial console

[Ladislav Klenovič]

Hi,
can anybody help me to setup the SCC1 port as serial console on MPC860 =
with kernel 2=2E6=2E15=2E4? I would like to use it as system console du=
ring the booting proccess=2E I can not get any output on serial console=
 during booting proccess, I use uboot=2E

thnx,
regards ladislav

Re: SCC1 as serial console

[Laurent Pinchart]

Hi Ladislav,

> can anybody help me to setup the SCC1 port as serial console on MPC860 with
> kernel 2.6.15.4? I would like to use it as system console during the
> booting proccess. I can not get any output on serial console during booting
> proccess, I use uboot.

Does SCC1 work correctly in U-Boot ? If not, you should fix that first. I'll 
assume it does.

There are many issues which could lead to a silent serial console. The serial 
port could be misconfigured, or the kernel could crash for another reason 
before the serial port is initialized.

Have you been able to get a serial console on another serial port (SMC) ? Are 
the clock frequencies computed by U-Boot and passed to the Linux kernel 
correct ?

Do you have a hardware debugger (BDI2000) that you can connect to the 
processor to see if Linux crashes before initializing the serial port ? If 
not, you will probably have to take a try at led-debugging (make some leds 
blink at various point in the Linux kernel to try to find out what happens), 
but that's really no fun.

Laurent Pinchart

Debbugging technique (was: Re: SCC1 as serial console)

[Walter L. Wimer III]

On Mon, 2006-05-22 at 16:12 +0200, Laurent Pinchart wrote:
> Do you have a hardware debugger (BDI2000) that you can connect to the 
> processor to see if Linux crashes before initializing the serial
> port ? If not, you will probably have to take a try at led-debugging
> (make some leds blink at various point in the Linux kernel to try to
> find out what happens), but that's really no fun.

If your U-Boot works successfully, here's another technique I've used
recently:

First, on the 8xx (and probably on some other PowerPC's) you'll want to
change the cache mode to "write-through" rather than "copy-back".  On
8xx, there is a kernel configuration option to do this.

If you're lucky and printk() is working internally (even though your
console isn't), you can put printk()s in your code wherever you want and
then use U-Boot to examine printk()'s buffer.  Boot up your kernel with
your debugging code, let it run for a second or two (long enough that
you suspect it has reached the likely problem area), then press the hard
reset button on the board.  This will restart U-Boot.  If necessary,
press a key to stop U-Boot from autobooting.

Next look at the kernel's System.map file and search for
"log_buf" (without quotes).  This is the kernel virtual address of
printk()'s log buffer and will be something like 0xc018469c.  You'll
need to translate this to a physical address.  On PowerPC, usually you
can do this simply by changing the leading "c" to a zero "0".

Now, use U-Boot's "md" (memory display) command to view the log_buf
physical address, e.g.:

                md 0x0018469c

Hopefully, now you'll see printk's log messages and you'll be able to
figure out why your console isn't working.

In my case recently, I was unlucky.  My kernel problem occurred long
before printk() was initialized, so printk() didn't work for me.  When I
examined the log_buf, it was empty.  If this happens to you, then try
the next idea:

Somewhere in the kernel (I chose arch/ppc/syslib/m8xx_setup.c, but it
shouldn't really matter, as long as the file you choose is compiled and
linked as part of your particular kernel configuration), declare a
buffer or two for storing debugging info.  For example:

                char mycharbuff[1024];
                int  myintbuff[256];

Also declare pointers that you can use to write debugging info into the
above arrays:

                char *mycharptr = mycharbuff;
                int  *myintptr  = myintbuff;

Then, wherever you need debugging information in your code, add lines
like:

                mycharptr += sprintf(mycharptr, "Something happened!
                \n");
or
                *myintptr++ = 29;    /* code number of your choosing */

After recompiling your kernel, find your buffer addresses in System.map
as we did previously with log_buf.  Convert the virtual addresses to
physical addresses.  Again run your kernel, hit the hard reset button,
and then use U-Boot's "md" command to examine your custom buffers.
You'll probably determine the problem area fairly quickly after a few
iterations of adding debugging code and examining your custom buffers.

DISCLAIMER:  The sample code I've shown above is not SMP or preemption
safe!  It also doesn't check for buffer overflow!  This is debugging
code, meant to be removed after you've found the problem.  This
simplistic code is often sufficient when debugging simple early-boot
problems that cause the machine to crash within the first few moments
after boot.  If your debugging requirements are more complicated, you'll
want correspondingly more complex debugging code.  E.g. you'll want to
check buffer lengths, you may want to wrap back to the beginning of your
buffer when you hit the end, etc.  You may also need to deal with
SMP/preemption issues.  This code is not to be taken internally.  Your
mileage may vary.  These statements have not been evaluated by the Food
and Drug Administration.  This product is not intended to treat or cure
any disease.  :-)



Good Luck!!!

Walt Wimer
TimeSys Corporation

Re: SCC1 as serial console

[Jeff Angielski]

On Mon, 2006-05-22 at 15:33 +0200, Ladislav Klenovič wrote:
> Hi,
> can anybody help me to setup the SCC1 port as serial console on MPC860 
> with kernel 2.6.15.4? I would like to use it as system console during 
> the booting proccess. I can not get any output on serial console during 
> booting proccess, I use uboot.

What are your kernel command line arguments?  Are you passing the right
ones in?

Have you configured the SCC correctly in the kernel?  Chosen SCC1? Baud
rates correct?  etc.  

Does your hardware need any special tweaks to the SCC code that is in
u-boot but not your kernel?


Jeff Angielski
The PTR Group

Re: SCC1 as serial console

[a b]

experiment


__________
http://auto.sme.sk - Všetko o autách (novinky, testy, autosalón, autoškola, porovnaj si auto)

Re: SCC1 as serial console

[Ladislav Klenovič]

exp

Re: SCC1 as serial console

[Ladislav Klenovi?]

HOW TO REPLY ON POSTS ?????????????????????? !!!!!!!!!!!!!!!!!!!

>-----P?vodn? spr?va-----
>Od: Ladislav Klenovi? [mailto:lk99336@pobox=2Esk]
>Odoslan?: 22=2E m?ja 2006 13:33
>Komu: linuxppc-embedded@ozlabs=2Eorg
>Predmet: SCC1 as serial console
>
>
>Hi,
>can anybody help me to setup the SCC1 port as serial console on MPC860=
 with kernel 2=2E6=2E15=2E4? I would like to use it as system console d=
uring the booting proccess=2E I can not get any output on serial consol=
e during booting proccess, I use uboot=2E
>
>thnx,
>regards ladislav
>
>
>_______________________________________________
>Linuxppc-embedded mailing list
>Linuxppc-embedded@ozlabs=2Eorg
>https://ozlabs=2Eorg/mailman/listinfo/linuxppc-embedded