* Re: [PATCH] MTD: Add support for the PM82x Boards.
From: David Woodhouse @ 2005-11-23 13:03 UTC (permalink / raw)
To: hs; +Cc: linuxppc-dev, tglx, linux-mtd
In-Reply-To: <AHEILKONAKAEJPHNMOPNCEMHCDAA.hs@denx.de>
On Wed, 2005-11-23 at 13:37 +0100, Heiko Schocher wrote:
> now without drivers/mtd/devices/docprobe.c
Thanks. Are those Intel chips really not CFI-compliant?
Please could you also correct each instance of 'MB' to 'MiB'?
--
dwmw2
^ permalink raw reply
* Re: [PATCH] MTD: Add support for the PM82x Boards.
From: Heiko Schocher @ 2005-11-23 12:37 UTC (permalink / raw)
To: linux-mtd; +Cc: linuxppc-dev, tglx, David Woodhouse
Hello,
> > > Please use the new DiskOnChip driver in drivers/mtd/nand/ not the old
> > > one.
> >
> > I use the new driver.
> > I made the changes in drivers/mtd/devices/docprobe.c, because I
> > ported it from the 2.4 Kernel. Should I delete this and resubmit
> > the patch?
>
> Yes, please.
now without drivers/mtd/devices/docprobe.c
[PATCH] MTD: Add support for the PM82x Boards.
Included support for the NOR flashes on the Modul,
and for the DiskOnChip on the Board.
Signed-off-by: Heiko Schocher <hs@denx.de>
---
drivers/mtd/chips/jedec_probe.c | 50 +++++
drivers/mtd/maps/Kconfig | 6 +
drivers/mtd/maps/Makefile | 1
drivers/mtd/maps/pm82x.c | 360 +++++++++++++++++++++++++++++++++++++++
drivers/mtd/nand/diskonchip.c | 4
5 files changed, 421 insertions(+), 0 deletions(-)
diff --git a/drivers/mtd/chips/jedec_probe.c b/drivers/mtd/chips/jedec_probe.c
index edb306c..e230127 100644
--- a/drivers/mtd/chips/jedec_probe.c
+++ b/drivers/mtd/chips/jedec_probe.c
@@ -104,6 +104,11 @@
#define I28F320B3B 0x8897
#define I28F640B3T 0x8898
#define I28F640B3B 0x8899
+#define I28F640C3B 0x88CD
+#define I28F160F3T 0x88F3
+#define I28F160F3B 0x88F4
+#define I28F160C3T 0x88C2
+#define I28F160C3B 0x88C3
#define I82802AB 0x00ad
#define I82802AC 0x00ac
@@ -1080,6 +1085,51 @@ static const struct amd_flash_info jedec
}
}, {
.mfr_id = MANUFACTURER_INTEL,
+ .dev_id = I28F640C3B,
+ .name = "Intel 28F640C3B",
+ .uaddr = {
+ [0] = MTD_UADDR_UNNECESSARY, /* x8 */
+ [1] = MTD_UADDR_UNNECESSARY, /* x16 */
+ },
+ .DevSize = SIZE_8MiB,
+ .CmdSet = P_ID_INTEL_STD,
+ .NumEraseRegions= 2,
+ .regions = {
+ ERASEINFO(0x02000, 8),
+ ERASEINFO(0x10000, 127),
+ }
+ }, {
+ .mfr_id = MANUFACTURER_INTEL,
+ .dev_id = I28F160C3B,
+ .name = "Intel 28F160C3B",
+ .uaddr = {
+ [0] = MTD_UADDR_UNNECESSARY, /* x8 */
+ [1] = MTD_UADDR_UNNECESSARY, /* x16 */
+ },
+ .DevSize = SIZE_2MiB,
+ .CmdSet = P_ID_INTEL_STD,
+ .NumEraseRegions= 2,
+ .regions = {
+ ERASEINFO(0x02000, 8),
+ ERASEINFO(0x10000, 31),
+ }
+ }, {
+ .mfr_id = MANUFACTURER_INTEL,
+ .dev_id = I28F160C3T,
+ .name = "Intel 28F160C3T",
+ .uaddr = {
+ [0] = MTD_UADDR_UNNECESSARY, /* x8 */
+ [1] = MTD_UADDR_UNNECESSARY, /* x16 */
+ },
+ .DevSize = SIZE_2MiB,
+ .CmdSet = P_ID_INTEL_STD,
+ .NumEraseRegions= 2,
+ .regions = {
+ ERASEINFO(0x10000, 31),
+ ERASEINFO(0x02000, 8),
+ }
+ }, {
+ .mfr_id = MANUFACTURER_INTEL,
.dev_id = I82802AB,
.name = "Intel 82802AB",
.uaddr = {
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 846a533..237abe8 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -256,6 +256,12 @@ config MTD_SBC8240
Flash access on the SBC8240 board from Wind River. See
<http://www.windriver.com/products/sbc8240/>
+config MTD_PM82X
+ tristate "Flash device on PM82X Boards"
+ depends on PPC32 && 6xx && 8260 && MTD_COMPLEX_MAPPINGS && MTD_PARTITIONS
+ help
+ Flash access on the PM82X boards from Microsys.
+
config MTD_TQM8XXL
tristate "CFI Flash device mapped on TQM8XXL"
depends on MTD_CFI && TQM8xxL
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
index 7d9e940..ecdc515 100644
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -73,3 +73,4 @@ obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
obj-$(CONFIG_MTD_PQ2FADS) += pq2fads.o
obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
obj-$(CONFIG_MTD_TQM834x) += tqm834x.o
+obj-$(CONFIG_MTD_PM82X) += pm82x.o
diff --git a/drivers/mtd/maps/pm82x.c b/drivers/mtd/maps/pm82x.c
new file mode 100644
index 0000000..dc0bc48
--- /dev/null
+++ b/drivers/mtd/maps/pm82x.c
@@ -0,0 +1,360 @@
+/*
+ * Copyright(C) 2005
+ * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
+ *
+ * Copyright(C) 2005
+ * Josef Wagner, MicroSys GmbH <wagner@microsys.de>
+ *
+ * This code is GPLed
+ *
+ */
+
+/*
+ * PM825/PM826 uses 4 x Intel 28F160C3B (16 Mbit)
+ * 4 x Intel 28F160C3 (16 Mbit) in one bank (64 bit bankwidth)
+ * for a total of 8MB flash
+ *
+ * PM827/PM828 uses 4 x Intel 28F640C3 (64 Mbit)
+ * in one bank (64 bit bankwidth)
+ * for a total of 32MB flash
+
+ * Thus we have to chose:
+ * - Support 64-bit bankwidth => CONFIG_MTD_CFI_B8
+ * - Support 4-chip flash interleave => CONFIG_MTD_CFI_I4
+*/
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <asm/io.h>
+#include <asm/ppcboot.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#if 0 /* Debugging turned off */
+# define debugk(fmt,args...) printk(fmt ,##args)
+#else
+# define debugk(fmt,args...)
+#endif
+
+#define FLASH_BANK_MAX 1
+
+/* The "residual" data board information structure the boot loader
+ * hands to us.
+ */
+extern unsigned char __res[];
+
+/* trivial struct to describe partition information */
+struct mtd_part_def
+{
+ int nums;
+ unsigned char *type;
+ struct mtd_partition* mtd_part;
+};
+
+static struct mtd_info* mtd_banks[FLASH_BANK_MAX];
+static struct map_info* map_banks[FLASH_BANK_MAX];
+static struct mtd_part_def part_banks[FLASH_BANK_MAX];
+static unsigned long num_banks;
+static unsigned long start_scan_addr;
+
+static map_word pm82x_read64(struct map_info *map, unsigned long ofs)
+{
+ map_word val;
+ val.x[0] = *((volatile __u32 *)(map->map_priv_1 + ofs));
+ val.x[1] = *(((volatile __u32 *)(map->map_priv_1 + ofs)) + 1);
+ return val;
+}
+
+static void pm82x_copy_from(struct map_info *map,
+ void *to, unsigned long from, ssize_t len)
+{
+ memcpy_fromio(to, (void *)(map->map_priv_1 + from), len);
+}
+
+static void pm82x_write64 (struct map_info *map, map_word map_d,
+ unsigned long adr)
+{
+ ulong addr = map->map_priv_1 + adr;
+ __u64 d = ((__u64)map_d.x[0] << 32) + map_d.x[1];
+ __u64 * data = &d;
+ ulong flags;
+ volatile ulong msr;
+ ulong saved_msr;
+ volatile long saved_fr[2];
+
+ local_irq_save (flags);
+
+ __asm__ __volatile__ ("mfmsr %0" : "=r" (msr):);
+ saved_msr = msr;
+ msr |= MSR_FP;
+ msr &= ~(MSR_FE0 | MSR_FE1);
+
+ __asm__ __volatile__ (
+ "mtmsr %0\n"
+ "isync\n"
+ :
+ : "r" (msr));
+
+ __asm__ __volatile__ (
+ "stfd 1, 0(%2)\n"
+ "lfd 1, 0(%0)\n"
+ "stfd 1, 0(%1)\n"
+ "lfd 1, 0(%2)\n"
+ :
+ : "r" (data), "r" (addr), "b" (saved_fr)
+ );
+
+ __asm__ __volatile__ (
+ "mtmsr %0\n"
+ "isync\n"
+ :
+ : "r" (saved_msr));
+
+ local_irq_restore (flags);
+}
+
+static void pm82x_copy_to(struct map_info *map,
+ unsigned long to, const void *from, ssize_t len)
+{
+ memcpy_toio((void *)(map->map_priv_1 + to), from, len);
+}
+
+/*
+ * The following defines the partition layout of PM825/PM826 boards.
+ *
+ * See include/linux/mtd/partitions.h for definition of the
+ * mtd_partition structure.
+ *
+ */
+
+#ifdef CONFIG_MTD_PARTITIONS
+/* partition definition for first (and only) flash bank
+ * also ref. to "drivers/char/flash_config.c"
+ */
+static struct mtd_partition pm82x_partitions_8M[] = {
+ {
+ name: "U-Boot", /* U-Boot image */
+ offset: 0x00000000,
+ size: 0x00040000, /* 256 KB */
+ },
+ {
+ name: "kernel", /* Linux kernel image */
+ offset: 0x00040000,
+ size: 0x000C0000, /* 768 KB */
+ },
+ {
+ name: "ramdisk", /* Ramdisk image */
+ offset: 0x00100000,
+ size: 0x00300000, /* 3 MB */
+ },
+ {
+ name: "user", /* User file system */
+ offset: 0x00400000,
+ size: 0x00400000, /* 4 MB */
+ },
+};
+
+static struct mtd_partition pm82x_partitions_32M[] = {
+ {
+ name: "U-Boot", /* U-Boot image */
+ offset: 0x00000000,
+ size: 0x00040000, /* 256 KB */
+ },
+ {
+ name: "kernel", /* Linux kernel image */
+ offset: 0x00040000,
+ size: 0x000C0000, /* 768 KB */
+ },
+ {
+ name: "ramdisk", /* Ramdisk image */
+ offset: 0x00100000,
+ size: 0x00300000, /* 3 MB */
+ },
+ {
+ name: "user", /* User file system */
+ offset: 0x00400000,
+ size: 0x01C00000, /* 28 MB */
+ },
+};
+
+#endif /* CONFIG_MTD_PARTITIONS */
+
+#define NB_OF(x) (sizeof (x) / sizeof (x[0]))
+
+int __init init_pm82x_mtd(void)
+{
+ int idx = 0, ret = 0;
+ unsigned long flash_addr, flash_size, mtd_size = 0;
+
+ /* pointer to PM82x board info data */
+ bd_t *bd = (bd_t *)__res;
+
+#ifdef CONFIG_MTD_CMDLINE_PARTS
+ int n;
+ char mtdid[10];
+ const char *part_probes[] = { "cmdlinepart", NULL };
+#endif
+
+ flash_addr = bd->bi_flashstart;
+ flash_size = bd->bi_flashsize;
+
+ /* request maximum flash size address space */
+ start_scan_addr = (unsigned long)ioremap(flash_addr, flash_size);
+ if (!start_scan_addr) {
+ printk("%s: Failed to ioremap address: 0x%lx\n",
+ __FUNCTION__, flash_addr);
+ return -EIO;
+ }
+
+ for(idx = 0 ; idx < FLASH_BANK_MAX ; idx++) {
+ if (mtd_size >= flash_size)
+ break;
+
+ debugk ("%s: chip probing count %d\n", __FUNCTION__, idx);
+
+ map_banks[idx] = (struct map_info *)kmalloc(sizeof(struct map_info),
+ GFP_KERNEL);
+ if (map_banks[idx] == NULL) {
+ ret = -ENOMEM;
+ goto error_mem;
+ }
+ memset((void *)map_banks[idx], 0, sizeof(struct map_info));
+ map_banks[idx]->name = (char *)kmalloc(16, GFP_KERNEL);
+ if (map_banks[idx]->name == NULL) {
+ ret = -ENOMEM;
+ goto error_mem;
+ }
+ memset((void *)map_banks[idx]->name, 0, 16);
+
+ sprintf(map_banks[idx]->name, "PM82x-%d", idx);
+ map_banks[idx]->size = flash_size;
+ map_banks[idx]->bankwidth = 8;
+ map_banks[idx]->read = pm82x_read64;
+ map_banks[idx]->copy_from = pm82x_copy_from;
+ map_banks[idx]->write = pm82x_write64;
+ map_banks[idx]->copy_to = pm82x_copy_to;
+ map_banks[idx]->map_priv_1=
+ start_scan_addr + ((idx > 0) ?
+ (mtd_banks[idx-1] ? mtd_banks[idx-1]->size : 0) : 0);
+
+ /* start to probe flash chips */
+ mtd_banks[idx] = do_map_probe("jedec_probe", map_banks[idx]);
+ if (mtd_banks[idx]) {
+ mtd_banks[idx]->owner = THIS_MODULE;
+ mtd_size += mtd_banks[idx]->size;
+ num_banks++;
+ debugk ("%s: bank %ld, name: %s, size: %d bytes \n",
+ __FUNCTION__,
+ num_banks,
+ mtd_banks[idx]->name,
+ mtd_banks[idx]->size);
+ }
+ }
+
+ /* no supported flash chips found */
+ if (!num_banks) {
+ printk("PM82x: No supported flash chips found!\n");
+ ret = -ENXIO;
+ goto error_mem;
+ }
+
+#ifdef CONFIG_MTD_PARTITIONS
+ /*
+ * Select static partition definitions
+ */
+ if (flash_size == 0x800000) {
+ part_banks[0].mtd_part = pm82x_partitions_8M;
+ part_banks[0].nums = NB_OF(pm82x_partitions_8M);
+ } else {
+ part_banks[0].mtd_part = pm82x_partitions_32M;
+ part_banks[0].nums = NB_OF(pm82x_partitions_32M);
+ }
+ part_banks[0].type = "static image";
+
+ for(idx = 0; idx < num_banks ; idx++) {
+#ifdef CONFIG_MTD_CMDLINE_PARTS
+ sprintf(mtdid, "%d", idx);
+ n = parse_mtd_partitions(mtd_banks[idx],
+ part_probes,
+ &part_banks[idx].mtd_part,
+ 0);
+ debugk ("%s: %d command line partitions on bank %s\n",
+ __FUNCTION__, n, mtdid);
+ if (n > 0) {
+ part_banks[idx].type = "command line";
+ part_banks[idx].nums = n;
+ }
+#endif /* CONFIG_MTD_CMDLINE_PARTS */
+
+ if (part_banks[idx].nums == 0) {
+ printk (KERN_NOTICE
+ "PM82x flash bank %d: no partition info "
+ "available, registering whole device\n", idx);
+ add_mtd_device(mtd_banks[idx]);
+ } else {
+ printk (KERN_NOTICE
+ "PM82x flash bank %d: Using %s partition "
+ "definition\n", idx, part_banks[idx].type);
+ add_mtd_partitions (mtd_banks[idx],
+ part_banks[idx].mtd_part,
+ part_banks[idx].nums);
+ }
+ }
+#else /* ! CONFIG_MTD_PARTITIONS */
+ printk (KERN_NOTICE "PM82x flash: registering %d flash banks "
+ "at once\n", num_banks);
+
+ for(idx = 0 ; idx < num_banks ; idx++) {
+ add_mtd_device(mtd_banks[idx]);
+ }
+#endif /* CONFIG_MTD_PARTITIONS */
+
+ return 0;
+error_mem:
+ for (idx = 0 ; idx < FLASH_BANK_MAX ; idx++) {
+ if (map_banks[idx] != NULL) {
+ if (map_banks[idx]->name != NULL) {
+ kfree(map_banks[idx]->name);
+ map_banks[idx]->name = NULL;
+ }
+ kfree(map_banks[idx]);
+ map_banks[idx] = NULL;
+ }
+ }
+
+ iounmap((void *)start_scan_addr);
+
+ return ret;
+}
+
+static void __exit cleanup_pm82x_mtd(void)
+{
+ unsigned int idx = 0;
+ for(idx = 0 ; idx < num_banks ; idx++) {
+ /* destroy mtd_info previously allocated */
+ if (mtd_banks[idx]) {
+ del_mtd_partitions(mtd_banks[idx]);
+ map_destroy(mtd_banks[idx]);
+ }
+ /* release map_info not used anymore */
+ kfree(map_banks[idx]->name);
+ kfree(map_banks[idx]);
+ }
+ if (start_scan_addr) {
+ iounmap((void *)start_scan_addr);
+ start_scan_addr = 0;
+ }
+}
+
+module_init(init_pm82x_mtd);
+module_exit(cleanup_pm82x_mtd);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Wolfgang Denk <wd@denx.de>");
+MODULE_DESCRIPTION("MTD map driver for PM82x boards");
diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/diskonchip.c
index 21d4e8f..bf7cf54 100644
--- a/drivers/mtd/nand/diskonchip.c
+++ b/drivers/mtd/nand/diskonchip.c
@@ -55,7 +55,11 @@ static unsigned long __initdata doc_loca
0xe8000, 0xea000, 0xec000, 0xee000,
#endif /* CONFIG_MTD_DOCPROBE_HIGH */
#elif defined(__PPC__)
+#if defined(CONFIG_PM82X)
+ 0xff800000,
+#else
0xe4000000,
+#endif
#elif defined(CONFIG_MOMENCO_OCELOT)
0x2f000000,
0xff000000,
\f
!-------------------------------------------------------------flip-
^ permalink raw reply related
* RE: [PATCH] MTD: Add support for the PM82x Boards.
From: Thomas Gleixner @ 2005-11-23 10:39 UTC (permalink / raw)
To: hs; +Cc: linuxppc-dev, David Woodhouse, linux-mtd
In-Reply-To: <AHEILKONAKAEJPHNMOPNKEMACDAA.hs@denx.de>
On Tue, 2005-11-22 at 07:18 +0100, Heiko Schocher wrote:
> > Please use the new DiskOnChip driver in drivers/mtd/nand/ not the old
> > one.
>
> I use the new driver.
> I made the changes in drivers/mtd/devices/docprobe.c, because I
> ported it from the 2.4 Kernel. Should I delete this and resubmit
> the patch?
Yes, please.
tglx
^ permalink raw reply
* RE: Booting hangs after "Calibrating delay loop..."
From: Nguyen Thanh Binh @ 2005-11-23 9:52 UTC (permalink / raw)
To: Jaap de Jong, linuxppc-embedded
In-Reply-To: <6915D0AE8B9047438F320B466AE30FDD152556@nvs0003.nedap.local>
Hi Jaap,
Thank you for replying.
I am still stuck on that.
Best regards,
Binh Nguyen
--- Jaap de Jong <jaap.dejong@nedap.com> wrote:
> Hi Binh,
>
> I am working with this fpga too, different board,
> same linux version,
> and not very succesfull until now too...
> But my build passes the "Calibrating delay loop..."
> and prints the
> correct value!
> Just guessing... perhaps your problem is timer
> related. Fi no timer
> interrupts?
>
> Best regards!
>
> Jaap de Jong
>
>
>
> > Hi all,
> >
> > When booting Monta Vista Linux on Memec board
> > (Virtex-4 FX12 LC), it hung after printing the
> > following message:
> >
> > "Calibrating delay loop..."
> >
> > By looking at the source code, I found that in the
> > init/main.c the problem came from the
> > calibrate_delay()
> > function: jiffies was not incremented (jiffies was
> > always equal to 0).
> >
> > Have anyone get the similar problem or any
> experience
> > to fix it?
>
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
>
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>
___________________________________________________________
Yahoo! Model Search 2005 - Find the next catwalk superstars - http://uk.news.yahoo.com/hot/model-search/
^ permalink raw reply
* Generic ethernet Driver For SMSC91111
From: srideep.devireddy @ 2005-11-23 8:31 UTC (permalink / raw)
To: linuxppc-embedded
[-- Attachment #1: Type: text/plain, Size: 903 bytes --]
HI All ,
Can some one help out in doing generic Ethernet driver functionalities
similar to SMSC91111, this is basically for MIPS ... but I am trying to
use SMSC driver in U-boot to port the same to other processor. So can
you kindly let me know which the major functionalities so that which I
can port them. It may be few functions .... So can you let me know what
those are and how to start with?
Awaiting reply on this regard ....
Best Regards
Srideep
Confidentiality Notice
The information contained in this electronic message and any attachments to this message are intended
for the exclusive use of the addressee(s) and may contain confidential or privileged information. If
you are not the intended recipient, please notify the sender at Wipro or Mailadmin@wipro.com immediately
and destroy all copies of this message and any attachments.
[-- Attachment #2: Type: text/html, Size: 3249 bytes --]
^ permalink raw reply
* Fwd: Anyone using Montavista mobilinux?
From: Paulinha @ 2005-11-23 7:29 UTC (permalink / raw)
To: Linuxppc-embedded, akonovalov
In-Reply-To: <43838F15.2030201@ru.mvista.com>
[-- Attachment #1: Type: text/plain, Size: 1614 bytes --]
Lots of thanks for the reply.
If you do not bother to aswer me again, do you know which devices are
supported by Mobilinux? I cannot find that information in the web, and if
one of them is Virtex II-Pro, it would be a good new for us.
Thanks again!
Paula
Paulinha wrote:
> Hi all,
>
> I am starting a new design for a mobile device, with a virtex 4, and
> based on the ppc405 hard core it has inside.
>
> Because of power issues, we are thinking about a OS which implies low
> disipation, and we have heared about mobilinux (Montavista distribution,
> I think).
Yes, mobilinux is a MontaVista product (it used to be called Consumer
Electronics Edition some time ago).
So far I haven't heard about plans to support Virtex 4 in Mobilinux.
Please contact MVista in an official way - I was mostly developing for
the Professional Edition (the most generic distribution with minimal
set of additional features) and may not have the whole picture.
Probably Virtex 4 support in Mobilinux could be done as a Professional
Services project.
Pro Edition LSP for Virtex 4 based Xilinx ML403 board should be available
in Q1 2006. But power consumption is not in the requirements for this LSP.
Best regards,
Andrei
> I would like to hear some oppinions or different possibilities.
>
> Thanks and have a nice day!
> Paula
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Linuxppc-embedded mailing list
> Linuxppc-embedded@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-embedded
[-- Attachment #2: Type: text/html, Size: 1949 bytes --]
^ permalink raw reply
* Re: [PATCH] ppc32: smc1_lineif fix for mpc8272
From: Kumar Gala @ 2005-11-23 7:16 UTC (permalink / raw)
To: Mike Rapoport; +Cc: 'linuxppc-embedded@ozlabs.org'
In-Reply-To: <4380829E.7040804@compulab.co.il>
It this on some specific board with an MPC8272 on it?
- kumar
On Nov 20, 2005, at 8:05 AM, Mike Rapoport wrote:
> This patch fixes the pin assignment of SMC1 for MPC8272 family
>
> Signed-off-by: Mike Rapoport <mike@compulab.co.il>
>
>
> --
> Sincerely yours,
> Mike Rapoport
>
>
> diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/
> serial/cpm_uart/cpm_uart_cpm2.c
> --- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> +++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
> @@ -89,11 +89,19 @@ void smc1_lineif(struct uart_cpm_port *p
> {
> volatile iop_cpm2_t *io = &cpm2_immr->im_ioport;
>
> +#ifdef CONFIG_8272
> + /* SMC1 is only on port C on 8272 */
> + io->iop_pparc |= 0x0c000000;
> + io->iop_pdirc |= 0x04000000;
> + io->iop_pdirc &= ~0x08000000;
> + io->iop_psorc &= ~0x0c000000;
> +#else
> /* SMC1 is only on port D */
> io->iop_ppard |= 0x00c00000;
> io->iop_pdird |= 0x00400000;
> io->iop_pdird &= ~0x00800000;
> io->iop_psord &= ~0x00c00000;
> +#endif
>
> /* Wire BRG1 to SMC1 */
> cpm2_immr->im_cpmux.cmx_smr &= 0x0f;
^ permalink raw reply
* Re: [PATCH] I2C: Add I2C support for the MPC8260
From: Kumar Gala @ 2005-11-23 7:01 UTC (permalink / raw)
To: hs; +Cc: linuxppc-dev, lm-sensors
In-Reply-To: <AHEILKONAKAEJPHNMOPNMELLCDAA.hs@denx.de>
Can we rename the driver from mpc8260 -> cpm2. The driver should work
on any device that has a "CPM2" which includes a number of MPC82xx
and MPC85xx processors. So calling it and its config options, etc
MPC8260 is going to be confusing to users.
- kumar
On Nov 21, 2005, at 9:55 AM, Heiko Schocher wrote:
> Hello,
>
> the following Patch (against 2.6 kernel.org tree, COMMIT_ID:
> f093182d313edde9b1f86dbdaf40ba4da2dbd0e7) adds support for
> the I2C on a MPC8260.
> ---
> drivers/i2c/busses/Kconfig | 10 +
> drivers/i2c/busses/Makefile | 1
> drivers/i2c/busses/i2c-mpc8260.c | 617 +++++++++++++++++++++++++++
> +++++++++++
> include/linux/i2c-algo-8260.h | 26 ++
> include/linux/i2c-id.h | 3
> 5 files changed, 657 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 4010fe9..77f9c69 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -270,6 +270,16 @@ config I2C_MPC
> This driver can also be built as a module. If so, the module
> will be called i2c-mpc.
>
> +config I2C_MPC8260
> + tristate "MPC 8260"
> + depends on I2C && PPC32
> + help
> + If you say yes to this option, support will be included for the
> + I2C interface on the MPC8260.
> +
> + This driver can also be built as a module. If so, the module
> + will be called i2c-m8260.
> +
> config I2C_NFORCE2
> tristate "Nvidia nForce2, nForce3 and nForce4"
> depends on I2C && PCI
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index f1df00f..b4d8cea 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -43,6 +43,7 @@ obj-$(CONFIG_I2C_VIAPRO) += i2c-viapro.o
> obj-$(CONFIG_I2C_VOODOO3) += i2c-voodoo3.o
> obj-$(CONFIG_SCx200_ACB) += scx200_acb.o
> obj-$(CONFIG_SCx200_I2C) += scx200_i2c.o
> +obj-$(CONFIG_I2C_MPC8260) += i2c-mpc8260.o
>
> ifeq ($(CONFIG_I2C_DEBUG_BUS),y)
> EXTRA_CFLAGS += -DDEBUG
> diff --git a/drivers/i2c/busses/i2c-mpc8260.c b/drivers/i2c/busses/
> i2c-mpc8260.c
> new file mode 100644
> index 0000000..f1bfa51
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-mpc8260.c
> @@ -0,0 +1,617 @@
> +/*
> + * (C) Copyright 2005
> + * Heiko Schocher <hs@denx.de>
> + *
> + * This is a combined i2c adapter and algorithm driver for the
> + * MPC8260 Processor
> + *
> + * Release 0.1
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/config.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/sched.h>
> +#include <linux/init.h>
> +#include <linux/pci.h>
> +#include <asm/io.h>
> +#include <linux/fsl_devices.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <asm/immap_cpm2.h>
> +#include <asm/mpc8260.h>
> +#include <asm/cpm2.h>
> +
> +#include <linux/i2c-algo-8260.h>
> +#include <linux/platform_device.h>
> +
> +#define CPM_MAX_READ 513
> +
> +static wait_queue_head_t iic_wait;
> +static ushort r_tbase, r_rbase;
> +
> +int cpm_scan = 0;
> +int cpm_debug = 0;
> +
> +struct mpc_i2c {
> + u32 interrupt;
> + wait_queue_head_t queue;
> + struct i2c_adapter adap;
> + int irq;
> + u32 flags;
> + struct i2c_algo_8260_data *data;
> +};
> +
> +static struct i2c_algo_8260_data pm82x_data;
> +
> +static void
> +mpc8260_iic_init(struct i2c_algo_8260_data *data)
> +{
> + volatile cpm_cpm2_t *cp;
> + volatile cpm2_map_t *immap;
> +
> + cp = cpmp; /* Get pointer to Communication Processor */
> + immap = (cpm2_map_t *)CPM_MAP_ADDR; /* and to internal registers */
> +
> + *(ushort *)(&immap->im_dprambase[PROFF_I2C_BASE]) = PROFF_I2C;
> + data->iip = (iic_t *)&immap->im_dprambase[PROFF_I2C];
> +
> + data->i2c = (i2c_cpm2_t *)&(immap->im_i2c);
> + data->cp = cp;
> +
> + /* Initialize Port D IIC pins.
> + */
> + immap->im_ioport.iop_ppard |= 0x00030000;
> + immap->im_ioport.iop_pdird &= ~0x00030000;
> + immap->im_ioport.iop_podrd |= 0x00030000;
> + immap->im_ioport.iop_psord |= 0x00030000;
> +
> + /* Allocate space for two transmit and two receive buffer
> + * descriptors in the DP ram.
> + */
> + data->dp_addr = cpm_dpalloc(sizeof(cbd_t) * 4, 8);
> +
> + /* ptr to i2c area */
> + data->i2c = (i2c_cpm2_t *)&(((cpm2_map_t *)CPM_MAP_ADDR)->im_i2c);
> +}
> +
> +static irqreturn_t mpc8260_i2c_isr(int irq, void *dev_id, struct
> pt_regs *regs)
> +{
> + struct mpc_i2c *mpc_i2c = dev_id;
> + struct i2c_algo_8260_data *cpm_adap = mpc_i2c->data;
> + volatile i2c_cpm2_t *i2c = cpm_adap->i2c;
> +
> + if (cpm_debug > 1)
> + printk(KERN_DEBUG "cpm_iic_interrupt(dev_id=%p)\n", dev_id);
> +
> + /* Clear interrupt.
> + */
> + i2c->i2c_i2cer = 0xff;
> +
> + /* Get 'me going again.
> + */
> + wake_up_interruptible(&iic_wait);
> + return IRQ_HANDLED;
> +}
> +
> +
> +static void
> +cpm_iic_init(struct i2c_algo_8260_data *cpm_adap)
> +{
> + volatile iic_t *iip = cpm_adap->iip;
> + volatile i2c_cpm2_t *i2c = cpm_adap->i2c;
> +
> + if (cpm_debug) printk(KERN_DEBUG "cpm_iic_init() - iip=%p\n",iip);
> +
> + /* Initialize the parameter ram.
> + * We need to make sure many things are initialized to zero,
> + * especially in the case of a microcode patch.
> + */
> + iip->iic_rstate = 0;
> + iip->iic_rdp = 0;
> + iip->iic_rbptr = 0;
> + iip->iic_rbc = 0;
> + iip->iic_rxtmp = 0;
> + iip->iic_tstate = 0;
> + iip->iic_tdp = 0;
> + iip->iic_tbptr = 0;
> + iip->iic_tbc = 0;
> + iip->iic_txtmp = 0;
> +
> + /* Set up the IIC parameters in the parameter ram.
> + */
> + iip->iic_tbase = r_tbase = cpm_adap->dp_addr;
> + iip->iic_rbase = r_rbase = cpm_adap->dp_addr + sizeof(cbd_t)*2;
> +
> + iip->iic_tfcr = CPMFCR_GBL | CPMFCR_EB;
> + iip->iic_rfcr = CPMFCR_GBL | CPMFCR_EB;
> +
> + /* Set maximum receive size.
> + */
> + iip->iic_mrblr = CPM_MAX_READ;
> +
> + /* Initialize Tx/Rx parameters.
> + */
> + {
> + volatile cpm_cpm2_t *cp = cpm_adap->cp;
> + cp->cp_cpcr =
> + mk_cr_cmd(CPM_CR_I2C_PAGE, CPM_CR_I2C_SBLOCK, 0x00,
> CPM_CR_INIT_TRX) | CPM_CR_FLG;
> + while (cp->cp_cpcr & CPM_CR_FLG);
> + }
> +
> + /* Select an arbitrary address. Just make sure it is unique.
> + */
> + i2c->i2c_i2add = 0x34;
> +
> + /* Divider is 2 * ( 15 + 3 )
> + */
> + i2c->i2c_i2brg = 0x0f;
> +
> + /* Pre-divider is BRGCLK/4
> + */
> + i2c->i2c_i2mod = 0x06;
> +
> + /* Disable interrupts.
> + */
> + i2c->i2c_i2cmr = 0;
> + i2c->i2c_i2cer = 0xff;
> +
> + init_waitqueue_head(&iic_wait);
> +}
> +
> +
> +#if 0
> +static int
> +cpm_iic_shutdown(struct i2c_algo_8260_data *cpm_adap)
> +{
> + volatile i2c_cpm2_t *i2c = cpm_adap->i2c;
> +
> + /* Shut down IIC.
> + */
> + i2c->i2c_i2mod = 0;
> + i2c->i2c_i2cmr = 0;
> + i2c->i2c_i2cer = 0xff;
> +
> + return(0);
> +}
> +#endif
> +
> +static void
> +cpm_reset_iic_params(volatile iic_t *iip)
> +{
> + iip->iic_tbase = r_tbase;
> + iip->iic_rbase = r_rbase;
> +
> + iip->iic_tfcr = CPMFCR_GBL | CPMFCR_EB;
> + iip->iic_rfcr = CPMFCR_GBL | CPMFCR_EB;
> +
> + iip->iic_mrblr = CPM_MAX_READ;
> +
> + iip->iic_rstate = 0;
> + iip->iic_rdp = 0;
> + iip->iic_rbptr = 0;
> + iip->iic_rbc = 0;
> + iip->iic_rxtmp = 0;
> + iip->iic_tstate = 0;
> + iip->iic_tdp = 0;
> + iip->iic_tbptr = 0;
> + iip->iic_tbc = 0;
> + iip->iic_txtmp = 0;
> +}
> +
> +#define BD_SC_NAK ((ushort)0x0004) /* NAK - did not respond */
> +#define CPM_CR_CLOSE_RXBD ((ushort)0x0007)
> +
> +static void force_close(struct i2c_algo_8260_data *cpm)
> +{
> +#if 0
> + volatile cpm_cpm2_t *cp = cpm->cp;
> +
> + if (cpm_debug) printk(KERN_DEBUG "force_close()\n");
> + cp->cp_cpcr =
> + mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_CLOSE_RXBD) |
> + CPM_CR_FLG;
> +
> + while (cp->cp_cpcr & CPM_CR_FLG);
> +#endif
> +}
> +
> +
> +/* Read from IIC...
> + * abyte = address byte, with r/w flag already set
> + */
> +static int
> +cpm_iic_read(struct i2c_algo_8260_data *cpm, u_char abyte, char
> *buf, int count)
> +{
> + volatile cpm2_map_t *immap = (cpm2_map_t *)CPM_MAP_ADDR;
> + volatile iic_t *iip = cpm->iip;
> + volatile i2c_cpm2_t *i2c = cpm->i2c;
> + volatile cbd_t *tbdf, *rbdf;
> + u_char *tb;
> + unsigned long flags;
> +
> + if (count >= CPM_MAX_READ)
> + return -EINVAL;
> +
> + tbdf = (cbd_t *)&immap->im_dprambase[iip->iic_tbase];
> + rbdf = (cbd_t *)&immap->im_dprambase[iip->iic_rbase];
> +
> + /* To read, we need an empty buffer of the proper length.
> + * All that is used is the first byte for address, the remainder
> + * is just used for timing (and doesn't really have to exist).
> + */
> + if (/*cpm->reloc*/0) {
> + cpm_reset_iic_params(iip);
> + }
> + tb = cpm->temp;
> + tb = (u_char *)(((uint)tb + 15) & ~15);
> + tb[0] = abyte; /* Device address byte w/rw flag */
> +
> + dma_cache_wback_inv (tb, 1);
> +
> + if (cpm_debug) printk(KERN_DEBUG "cpm_iic_read(abyte=0x%x)\n",
> abyte);
> +
> + tbdf->cbd_bufaddr = __pa(tb);
> + tbdf->cbd_datlen = count + 1;
> + tbdf->cbd_sc =
> + BD_SC_READY | BD_SC_INTRPT | BD_SC_LAST |
> + BD_SC_WRAP | BD_IIC_START;
> +
> + rbdf->cbd_datlen = 0;
> + rbdf->cbd_bufaddr = __pa(buf);
> + rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
> +
> + if (count > 0 && count < CPM_MAX_READ)
> + iip->iic_mrblr = count; /* prevent excessive read */
> +
> + dma_cache_inv (buf, count);
> +
> + /* Chip bug, set enable here */
> + local_irq_save(flags);
> + i2c->i2c_i2cmr = 0x13; /* Enable some interupts */
> + i2c->i2c_i2cer = 0xff;
> + i2c->i2c_i2mod |= 1; /* Enable */
> + i2c->i2c_i2com = 0x81; /* Start master */
> +
> + /* Wait for IIC transfer */
> + interruptible_sleep_on(&iic_wait);
> + local_irq_restore(flags);
> + if (signal_pending(current))
> + return -EIO;
> +
> + if (cpm_debug) {
> + printk(KERN_DEBUG "tx sc %04x, rx sc %04x\n",
> + tbdf->cbd_sc, rbdf->cbd_sc);
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + printk(KERN_INFO "IIC read; no ack\n");
> + return 0;
> + }
> +
> + if (rbdf->cbd_sc & BD_SC_EMPTY) {
> + printk(KERN_INFO "IIC read; complete but rbuf empty\n");
> + force_close(cpm);
> + printk(KERN_INFO "tx sc %04x, rx sc %04x\n",
> + tbdf->cbd_sc, rbdf->cbd_sc);
> + }
> +
> + if (cpm_debug) printk(KERN_DEBUG "read %d bytes\n", rbdf-
> >cbd_datlen);
> +
> + if (rbdf->cbd_datlen < count) {
> + printk(KERN_INFO "IIC read; short, wanted %d got %d\n",
> + count, rbdf->cbd_datlen);
> + return 0;
> + }
> + if (cpm_debug) {
> + int u;
> + for (u = 0; u < count; u++) {
> + printk(KERN_DEBUG "buf[%d] = 0x%x\n", u, buf[u]);
> + }
> + }
> +
> +
> + return count;
> +}
> +
> +/* Write to IIC...
> + * addr = address byte, with r/w flag already set
> + */
> +static int
> +cpm_iic_write(struct i2c_algo_8260_data *cpm, u_char abyte, char
> *buf,int count)
> +{
> + volatile cpm2_map_t *immap = (cpm2_map_t *)CPM_MAP_ADDR;
> + volatile iic_t *iip = cpm->iip;
> + volatile i2c_cpm2_t *i2c = cpm->i2c;
> + volatile cbd_t *tbdf;
> + u_char *tb;
> + unsigned long flags;
> +
> + tb = cpm->temp;
> + tb = (u_char *)(((uint)tb + 15) & ~15);
> + *tb = abyte; /* Device address byte w/rw flag */
> +
> + dma_cache_wback_inv (tb, 1);
> + dma_cache_wback_inv (buf, count);
> +
> + if (cpm_debug) printk(KERN_DEBUG "cpm_iic_write(abyte=0x%x)\n",
> abyte);
> + if (cpm_debug) printk(KERN_DEBUG "buf[0] = 0x%x, buf[1] = 0x%x
> \n", buf[0], buf[1]);
> +
> + /* set up 2 descriptors */
> + tbdf = (cbd_t *)&immap->im_dprambase[iip->iic_tbase];
> +
> + tbdf[0].cbd_bufaddr = __pa(tb);
> + tbdf[0].cbd_datlen = 1;
> + tbdf[0].cbd_sc = BD_SC_READY | BD_IIC_START;
> +
> + tbdf[1].cbd_bufaddr = __pa(buf);
> + tbdf[1].cbd_datlen = count;
> + tbdf[1].cbd_sc = BD_SC_READY | BD_SC_INTRPT | BD_SC_LAST |
> BD_SC_WRAP;
> +
> + /* Chip bug, set enable here */
> + local_irq_save(flags);;
> + i2c->i2c_i2cmr = 0x13; /* Enable some interupts */
> + i2c->i2c_i2cer = 0xff;
> + i2c->i2c_i2mod |= 1; /* Enable */
> + i2c->i2c_i2com = 0x81; /* Start master */
> +
> + /* Wait for IIC transfer */
> + interruptible_sleep_on(&iic_wait);
> + local_irq_restore(flags);
> + if (signal_pending(current))
> + return -EIO;
> +
> + if (cpm_debug) {
> + printk(KERN_DEBUG "tx0 sc %04x, tx1 sc %04x\n",
> + tbdf[0].cbd_sc, tbdf[1].cbd_sc);
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + printk(KERN_INFO "IIC write; no ack\n");
> + return 0;
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_READY) {
> + printk(KERN_INFO "IIC write; complete but tbuf ready\n");
> + return 0;
> + }
> +
> + return count;
> +}
> +
> +#if 0
> +/* See if an IIC address exists..
> + * addr = 7 bit address, unshifted
> + */
> +static int
> +cpm_iic_tryaddress(struct i2c_algo_8260_data *cpm, int addr)
> +{
> + volatile cpm2_map_t *immap = (cpm2_map_t *)CPM_MAP_ADDR;
> + volatile iic_t *iip = cpm->iip;
> + volatile i2c_cpm2_t *i2c = cpm->i2c;
> + volatile cbd_t *tbdf, *rbdf;
> + u_char *tb;
> + unsigned long flags, len;
> +
> + if (cpm_debug > 1)
> + printk(KERN_DEBUG "cpm_iic_tryaddress(cpm=%p,addr=%d)\n", cpm,
> addr);
> +
> + if (cpm_debug && addr == 0) {
> + printk(KERN_DEBUG "iip %p, dp_addr 0x%x\n", cpm->iip, cpm-
> >dp_addr);
> + printk(KERN_DEBUG "iic_tbase %d, r_tbase %d\n", iip->iic_tbase,
> r_tbase);
> + }
> +
> + tbdf = (cbd_t *)&immap->im_dprambase[iip->iic_tbase];
> + rbdf = (cbd_t *)&immap->im_dprambase[iip->iic_rbase];
> +
> + tb = cpm->temp;
> + tb = (u_char *)(((uint)tb + 15) & ~15);
> +
> + /* do a simple read */
> + tb[0] = (addr << 1) | 1; /* device address (+ read) */
> + len = 2;
> +
> + dma_cache_wback_inv (tb, 1);
> +
> + tbdf->cbd_bufaddr = __pa(tb);
> + tbdf->cbd_datlen = len;
> + tbdf->cbd_sc =
> + BD_SC_READY | BD_SC_INTRPT | BD_SC_LAST |
> + BD_SC_WRAP | BD_IIC_START;
> +
> + rbdf->cbd_datlen = 0;
> + rbdf->cbd_bufaddr = __pa(tb+2);
> + rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
> +
> + local_irq_save(flags);
> + i2c->i2c_i2cmr = 0x13; /* Enable some interupts */
> + i2c->i2c_i2cer = 0xff;
> + i2c->i2c_i2mod |= 1; /* Enable */
> + i2c->i2c_i2com = 0x81; /* Start master */
> +
> + if (cpm_debug > 1) printk(KERN_DEBUG "about to sleep\n");
> +
> + /* wait for IIC transfer */
> + interruptible_sleep_on(&iic_wait);
> + local_irq_restore(flags);
> + if (signal_pending(current))
> + return -EIO;
> +
> + if (cpm_debug > 1) printk(KERN_DEBUG "back from sleep\n");
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + if (cpm_debug > 1) printk(KERN_DEBUG "IIC try; no ack\n");
> + return 0;
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_READY) {
> + printk(KERN_INFO "IIC try; complete but tbuf ready\n");
> + }
> +
> + return 1;
> +}
> +#endif
> +
> +static int mpc8260_xfer(struct i2c_adapter *adap, struct i2c_msg
> *msgs, int num)
> +{
> + struct i2c_msg *pmsg;
> + int i;
> + int ret = 0;
> + struct mpc_i2c *mpc_i2c = i2c_get_adapdata(adap);
> + struct i2c_algo_8260_data *data = mpc_i2c->data;
> + u_char addr;
> +
> + for (i = 0; i < num; i++) {
> + pmsg = &msgs[i];
> +
> + if (cpm_debug)
> + printk(KERN_DEBUG "i2c-algo-8260.o: "
> + "#%d addr=0x%x flags=0x%x len=%d\n",
> + i, pmsg->addr, pmsg->flags, pmsg->len);
> +
> + addr = pmsg->addr << 1;
> + if (pmsg->flags & I2C_M_RD )
> + addr |= 1;
> + if (pmsg->flags & I2C_M_REV_DIR_ADDR )
> + addr ^= 1;
> +
> + if (!(pmsg->flags & I2C_M_NOSTART)) {
> + }
> + if (pmsg->flags & I2C_M_RD ) {
> + /* read bytes into buffer*/
> + ret = cpm_iic_read(data, addr, pmsg->buf, pmsg->len);
> + if (cpm_debug)
> + printk(KERN_DEBUG "i2c-algo-8260.o: read %d bytes\n", ret);
> + if (ret < pmsg->len ) {
> + return (ret<0)? ret : -EREMOTEIO;
> + }
> + } else {
> + /* write bytes from buffer */
> + ret = cpm_iic_write(data, addr, pmsg->buf, pmsg->len);
> + if (cpm_debug)
> + printk(KERN_DEBUG "i2c-algo-8260.o: wrote %d\n", ret);
> + if (ret < pmsg->len ) {
> + return (ret<0) ? ret : -EREMOTEIO;
> + }
> + }
> + }
> + return (ret < 0) ? ret : num;
> +}
> +
> +static u32 mpc8260_functionality(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR |
> + I2C_FUNC_PROTOCOL_MANGLING;
> +}
> +
> +static struct i2c_algorithm mpc8260_algo = {
> + .master_xfer = mpc8260_xfer,
> + .functionality = mpc8260_functionality,
> +};
> +
> +static struct i2c_adapter mpc8260_ops = {
> + .owner = THIS_MODULE,
> + .name = "MPC 8260 adapter",
> + .id = I2C_HW_MPC8260,
> + .algo = &mpc8260_algo,
> + .class = I2C_CLASS_HWMON,
> + .timeout = 1,
> + .retries = 1
> +};
> +
> +static int fsl_i2c_probe(struct device *device)
> +{
> + int result = 0;
> + struct mpc_i2c *i2c;
> + struct platform_device *pdev = to_platform_device(device);
> + struct fsl_i2c_platform_data *pdata;
> +
> + pdata = (struct fsl_i2c_platform_data *) pdev->dev.platform_data;
> +
> + if (!(i2c = kmalloc(sizeof(*i2c), GFP_KERNEL))) {
> + return -ENOMEM;
> + }
> + memset(i2c, 0, sizeof(*i2c));
> +
> + i2c->data = &pm82x_data;
> + /* CPM Plattform initialisation */
> + mpc8260_iic_init (i2c->data);
> + /* CPM init */
> + cpm_iic_init (i2c->data);
> + i2c->irq = platform_get_irq(pdev, 0);
> +
> + if (i2c->irq != 0) {
> + if ((result = request_irq(i2c->irq, mpc8260_i2c_isr,
> + SA_SHIRQ, "i2c-mpc", i2c)) < 0) {
> + printk(KERN_ERR
> + "i2c-mpc - failed to attach interrupt\n");
> + goto fail_irq;
> + }
> + }
> + dev_set_drvdata(device, i2c);
> +
> + i2c->adap = mpc8260_ops;
> + i2c_set_adapdata(&i2c->adap, i2c);
> + i2c->adap.dev.parent = &pdev->dev;
> + if ((result = i2c_add_adapter(&i2c->adap)) < 0) {
> + printk(KERN_ERR "i2c-mpc - failed to add adapter\n");
> + goto fail_add;
> + }
> +
> + return result;
> +
> + fail_add:
> + if (i2c->irq != 0)
> + free_irq(i2c->irq, NULL);
> + fail_irq:
> + kfree(i2c);
> + return result;
> +};
> +
> +static int fsl_i2c_remove(struct device *device)
> +{
> + struct mpc_i2c *i2c = dev_get_drvdata(device);
> +
> + /* hier noich irgendwo das dpalloc wieder freigeben */
> + cpm_dpfree (i2c->data->dp_addr);
> +
> + i2c_del_adapter(&i2c->adap);
> + dev_set_drvdata(device, NULL);
> +
> + if (i2c->irq != 0)
> + free_irq(i2c->irq, i2c);
> +
> + kfree(i2c);
> + return 0;
> +};
> +
> +/* Structure for a device driver */
> +static struct device_driver fsl_i2c_driver = {
> + .name = "fsl-cpm-i2c",
> + .bus = &platform_bus_type,
> + .probe = fsl_i2c_probe,
> + .remove = fsl_i2c_remove,
> +};
> +
> +static int __init fsl_i2c_init(void)
> +{
> + return driver_register(&fsl_i2c_driver);
> +}
> +
> +static void __exit fsl_i2c_exit(void)
> +{
> + driver_unregister(&fsl_i2c_driver);
> +}
> +
> +module_init(fsl_i2c_init);
> +module_exit(fsl_i2c_exit);
> +
> +MODULE_AUTHOR("Heiko Schocher <hs@denx.de>");
> +MODULE_DESCRIPTION
> + ("I2C-Bus adapter for MPC8260 processors");
> +MODULE_LICENSE("GPL");
> diff --git a/include/linux/i2c-algo-8260.h b/include/linux/i2c-
> algo-8260.h
> new file mode 100644
> index 0000000..73b3e33
> --- /dev/null
> +++ b/include/linux/i2c-algo-8260.h
> @@ -0,0 +1,26 @@
> +/*
> ----------------------------------------------------------------------
> --- */
> +/* i2c-algo-8260.h i2c driver algorithms for MPX8260 CPM */
> +/*
> ----------------------------------------------------------------------
> --- */
> +
> +/* $Id$ */
> +
> +#ifndef I2C_ALGO_8260_H
> +#define I2C_ALGO_8260_H 1
> +
> +#include <linux/i2c.h>
> +
> +struct i2c_algo_8260_data {
> + uint dp_addr;
> + int reloc;
> + volatile i2c_cpm2_t *i2c;
> + volatile iic_t *iip;
> + volatile cpm_cpm2_t *cp;
> +
> + int (*setisr) (int irq,
> + void (*func)(int, void (*)(void *), void *),
> + void *data);
> +
> + u_char temp[513];
> +};
> +
> +#endif /* I2C_ALGO_8260_H */
> diff --git a/include/linux/i2c-id.h b/include/linux/i2c-id.h
> index 1543daa..35b0a57 100644
> --- a/include/linux/i2c-id.h
> +++ b/include/linux/i2c-id.h
> @@ -223,6 +223,9 @@
> /* --- PowerPC on-chip adapters */
> #define I2C_HW_OCP 0x120000 /* IBM on-chip I2C adapter */
>
> +/* --- MPC8260 PowerPC adapters */
> +#define I2C_HW_MPC8260 0x100002 /* MPC8260 I2C adapter */
> +
> /* --- Broadcom SiByte adapters */
> #define I2C_HW_SIBYTE 0x150000
>
>
>
> !-------------------------------------------------------------flip-
>
>
>
> Signed-off-by: Heiko Schocher <hs@denx.de>
>
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
^ permalink raw reply
* [PATCH] powerpc: convert macio_asic to use prom_parse
From: Benjamin Herrenschmidt @ 2005-11-23 6:59 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc64-dev, linuxppc-dev list
Converts the macio_asic core to use the new OF parsing routines instead
of relying on the pre-parsed values in struct device_node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Index: linux-serialfix/drivers/macintosh/macio_asic.c
===================================================================
--- linux-serialfix.orig/drivers/macintosh/macio_asic.c 2005-11-23 16:54:11.000000000 +1100
+++ linux-serialfix/drivers/macintosh/macio_asic.c 2005-11-23 16:54:26.000000000 +1100
@@ -3,6 +3,13 @@
* a MacIO ASIC. Interface to new driver model mostly
* stolen from the PCI version.
*
+ * Copyright (C) 2005 Ben. Herrenschmidt (benh@kernel.crashing.org)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
* TODO:
*
* - Don't probe below media bay by default, but instead provide
@@ -218,12 +225,14 @@ postcore_initcall(macio_bus_driver_init)
/**
- * macio_release_dev - free a macio device structure when all users of it are finished.
+ * macio_release_dev - free a macio device structure when all users of it are
+ * finished.
* @dev: device that's been disconnected
*
- * Will be called only by the device core when all users of this macio device are
- * done. This currently means never as we don't hot remove any macio device yet,
- * though that will happen with mediabay based devices in a later implementation.
+ * Will be called only by the device core when all users of this macio device
+ * are done. This currently means never as we don't hot remove any macio
+ * device yet, though that will happen with mediabay based devices in a later
+ * implementation.
*/
static void macio_release_dev(struct device *dev)
{
@@ -242,7 +251,8 @@ static void macio_release_dev(struct dev
* If this routine returns non-null, then the resource is completely
* skipped.
*/
-static int macio_resource_quirks(struct device_node *np, struct resource *res, int index)
+static int macio_resource_quirks(struct device_node *np, struct resource *res,
+ int index)
{
if (res->flags & IORESOURCE_MEM) {
/* Grand Central has too large resource 0 on some machines */
@@ -258,12 +268,15 @@ static int macio_resource_quirks(struct
np->addrs[index].size = 0x100;
res->end = res->start + 0xff;
}
- /* ESCC parent eats child resources. We could have added a level of hierarchy,
- * but I don't really feel the need for it */
+ /* ESCC parent eats child resources. We could have added a
+ * level of hierarchy, but I don't really feel the need
+ * for it
+ */
if (!strcmp(np->name, "escc"))
return 1;
/* ESCC has bogus resources >= 3 */
- if (index >= 3 && !(strcmp(np->name, "ch-a") && strcmp(np->name, "ch-b")))
+ if (index >= 3 && !(strcmp(np->name, "ch-a") &&
+ strcmp(np->name, "ch-b")))
return 1;
/* Media bay has too many resources, keep only first one */
if (index > 0 && !strcmp(np->name, "media-bay"))
@@ -285,6 +298,71 @@ static int macio_resource_quirks(struct
}
+static void macio_setup_interrupts(struct macio_dev *dev)
+{
+ struct device_node *np = dev->ofdev.node;
+ int i,j;
+
+ /* For now, we use pre-parsed entries in the device-tree for
+ * interrupt routing and addresses, but we should change that
+ * to dynamically parsed entries and so get rid of most of the
+ * clutter in struct device_node
+ */
+ for (i = j = 0; i < np->n_intrs; i++) {
+ struct resource *res = &dev->interrupt[j];
+
+ if (j >= MACIO_DEV_COUNT_IRQS)
+ break;
+ res->start = np->intrs[i].line;
+ res->flags = IORESOURCE_IO;
+ if (np->intrs[j].sense)
+ res->flags |= IORESOURCE_IRQ_LOWLEVEL;
+ else
+ res->flags |= IORESOURCE_IRQ_HIGHEDGE;
+ res->name = dev->ofdev.dev.bus_id;
+ if (macio_resource_quirks(np, res, i))
+ memset(res, 0, sizeof(struct resource));
+ else
+ j++;
+ }
+ dev->n_interrupts = j;
+}
+
+static void macio_setup_resources(struct macio_dev *dev,
+ struct resource *parent_res)
+{
+ struct device_node *np = dev->ofdev.node;
+ u32 *addr;
+ u64 size;
+ int index;
+
+ for (index = 0; (addr = of_get_address(np, index, &size)) != NULL;
+ index++) {
+ struct resource *res = &dev->resource[index];
+ if (index >= MACIO_DEV_COUNT_RESOURCES)
+ break;
+ res->start = of_translate_address(np, addr);
+ res->end = res->start + (unsigned long)size - 1;
+ res->flags = IORESOURCE_MEM;
+ res->name = dev->ofdev.dev.bus_id;
+
+ if (macio_resource_quirks(np, res, index)) {
+ memset(res, 0, sizeof(struct resource));
+ continue;
+ }
+ /* Currently, we consider failure as harmless, this may
+ * change in the future, once I've found all the device
+ * tree bugs in older machines & worked around them
+ */
+ if (insert_resource(parent_res, res)) {
+ printk(KERN_WARNING "Can't request resource "
+ "%d for MacIO device %s\n",
+ index, dev->ofdev.dev.bus_id);
+ }
+ }
+ dev->n_resources = index;
+}
+
/**
* macio_add_one_device - Add one device from OF node to the device tree
* @chip: pointer to the macio_chip holding the device
@@ -294,12 +372,13 @@ static int macio_resource_quirks(struct
* When media-bay is changed to hotswap drivers, this function will
* be exposed to the bay driver some way...
*/
-static struct macio_dev * macio_add_one_device(struct macio_chip *chip, struct device *parent,
- struct device_node *np, struct macio_dev *in_bay,
+static struct macio_dev * macio_add_one_device(struct macio_chip *chip,
+ struct device *parent,
+ struct device_node *np,
+ struct macio_dev *in_bay,
struct resource *parent_res)
{
struct macio_dev *dev;
- int i, j;
u32 *reg;
if (np == NULL)
@@ -326,7 +405,8 @@ static struct macio_dev * macio_add_one_
/* MacIO itself has a different reg, we use it's PCI base */
if (np == chip->of_node) {
- sprintf(dev->ofdev.dev.bus_id, "%1d.%08lx:%.*s", chip->lbus.index,
+ sprintf(dev->ofdev.dev.bus_id, "%1d.%08lx:%.*s",
+ chip->lbus.index,
#ifdef CONFIG_PCI
pci_resource_start(chip->lbus.pdev, 0),
#else
@@ -335,57 +415,16 @@ static struct macio_dev * macio_add_one_
MAX_NODE_NAME_SIZE, np->name);
} else {
reg = (u32 *)get_property(np, "reg", NULL);
- sprintf(dev->ofdev.dev.bus_id, "%1d.%08x:%.*s", chip->lbus.index,
+ sprintf(dev->ofdev.dev.bus_id, "%1d.%08x:%.*s",
+ chip->lbus.index,
reg ? *reg : 0, MAX_NODE_NAME_SIZE, np->name);
}
- /* For now, we use pre-parsed entries in the device-tree for
- * interrupt routing and addresses, but we should change that
- * to dynamically parsed entries and so get rid of most of the
- * clutter in struct device_node
- */
- for (i = j = 0; i < np->n_intrs; i++) {
- struct resource *res = &dev->interrupt[j];
-
- if (j >= MACIO_DEV_COUNT_IRQS)
- break;
- res->start = np->intrs[i].line;
- res->flags = IORESOURCE_IO;
- if (np->intrs[j].sense)
- res->flags |= IORESOURCE_IRQ_LOWLEVEL;
- else
- res->flags |= IORESOURCE_IRQ_HIGHEDGE;
- res->name = dev->ofdev.dev.bus_id;
- if (macio_resource_quirks(np, res, i))
- memset(res, 0, sizeof(struct resource));
- else
- j++;
- }
- dev->n_interrupts = j;
- for (i = j = 0; i < np->n_addrs; i++) {
- struct resource *res = &dev->resource[j];
-
- if (j >= MACIO_DEV_COUNT_RESOURCES)
- break;
- res->start = np->addrs[i].address;
- res->end = np->addrs[i].address + np->addrs[i].size - 1;
- res->flags = IORESOURCE_MEM;
- res->name = dev->ofdev.dev.bus_id;
- if (macio_resource_quirks(np, res, i))
- memset(res, 0, sizeof(struct resource));
- else {
- j++;
- /* Currently, we consider failure as harmless, this may
- * change in the future, once I've found all the device
- * tree bugs in older machines & worked around them
- */
- if (insert_resource(parent_res, res))
- printk(KERN_WARNING "Can't request resource %d for MacIO"
- " device %s\n", i, dev->ofdev.dev.bus_id);
- }
- }
- dev->n_resources = j;
+ /* Setup interrupts & resources */
+ macio_setup_interrupts(dev);
+ macio_setup_resources(dev, parent_res);
+ /* Register with core */
if (of_device_register(&dev->ofdev) != 0) {
printk(KERN_DEBUG"macio: device registration error for %s!\n",
dev->ofdev.dev.bus_id);
@@ -442,36 +481,42 @@ static void macio_pci_add_devices(struct
/* First scan 1st level */
for (np = NULL; (np = of_get_next_child(pnode, np)) != NULL;) {
- if (!macio_skip_device(np)) {
- of_node_get(np);
- mdev = macio_add_one_device(chip, &rdev->ofdev.dev, np, NULL, root_res);
- if (mdev == NULL)
- of_node_put(np);
- else if (strncmp(np->name, "media-bay", 9) == 0)
- mbdev = mdev;
- else if (strncmp(np->name, "escc", 4) == 0)
- sdev = mdev;
- }
+ if (macio_skip_device(np))
+ continue;
+ of_node_get(np);
+ mdev = macio_add_one_device(chip, &rdev->ofdev.dev, np, NULL,
+ root_res);
+ if (mdev == NULL)
+ of_node_put(np);
+ else if (strncmp(np->name, "media-bay", 9) == 0)
+ mbdev = mdev;
+ else if (strncmp(np->name, "escc", 4) == 0)
+ sdev = mdev;
}
/* Add media bay devices if any */
if (mbdev)
- for (np = NULL; (np = of_get_next_child(mbdev->ofdev.node, np)) != NULL;)
- if (!macio_skip_device(np)) {
- of_node_get(np);
- if (macio_add_one_device(chip, &mbdev->ofdev.dev, np, mbdev,
- root_res) == NULL)
- of_node_put(np);
- }
+ for (np = NULL; (np = of_get_next_child(mbdev->ofdev.node, np))
+ != NULL;) {
+ if (macio_skip_device(np))
+ continue;
+ of_node_get(np);
+ if (macio_add_one_device(chip, &mbdev->ofdev.dev, np,
+ mbdev, root_res) == NULL)
+ of_node_put(np);
+ }
+
/* Add serial ports if any */
if (sdev) {
- for (np = NULL; (np = of_get_next_child(sdev->ofdev.node, np)) != NULL;)
- if (!macio_skip_device(np)) {
- of_node_get(np);
- if (macio_add_one_device(chip, &sdev->ofdev.dev, np, NULL,
- root_res) == NULL)
- of_node_put(np);
- }
+ for (np = NULL; (np = of_get_next_child(sdev->ofdev.node, np))
+ != NULL;) {
+ if (macio_skip_device(np))
+ continue;
+ of_node_get(np);
+ if (macio_add_one_device(chip, &sdev->ofdev.dev, np,
+ NULL, root_res) == NULL)
+ of_node_put(np);
+ }
}
}
@@ -519,7 +564,8 @@ void macio_unregister_driver(struct maci
* Returns 0 on success, or %EBUSY on error. A warning
* message is also printed on failure.
*/
-int macio_request_resource(struct macio_dev *dev, int resource_no, const char *name)
+int macio_request_resource(struct macio_dev *dev, int resource_no,
+ const char *name)
{
if (macio_resource_len(dev, resource_no) == 0)
return 0;
@@ -606,20 +652,20 @@ static int __devinit macio_pci_probe(str
if (ent->vendor != PCI_VENDOR_ID_APPLE)
return -ENODEV;
- /* Note regarding refcounting: We assume pci_device_to_OF_node() is ported
- * to new OF APIs and returns a node with refcount incremented. This isn't
- * the case today, but on the other hand ppc32 doesn't do refcounting. This
- * will have to be fixed when going to ppc64. --BenH.
+ /* Note regarding refcounting: We assume pci_device_to_OF_node() is
+ * ported to new OF APIs and returns a node with refcount incremented.
*/
np = pci_device_to_OF_node(pdev);
if (np == NULL)
return -ENODEV;
- /* This assumption is wrong, fix that here for now until I fix the arch */
+ /* The above assumption is wrong !!!
+ * fix that here for now until I fix the arch code
+ */
of_node_get(np);
- /* We also assume that pmac_feature will have done a get() on nodes stored
- * in the macio chips array
+ /* We also assume that pmac_feature will have done a get() on nodes
+ * stored in the macio chips array
*/
chip = macio_find(np, macio_unknown);
of_node_put(np);
@@ -639,9 +685,9 @@ static int __devinit macio_pci_probe(str
/*
* HACK ALERT: The WallStreet PowerBook and some OHare based machines
- * have 2 macio ASICs. I must probe the "main" one first or IDE ordering
- * will be incorrect. So I put on "hold" the second one since it seem to
- * appear first on PCI
+ * have 2 macio ASICs. I must probe the "main" one first or IDE
+ * ordering will be incorrect. So I put on "hold" the second one since
+ * it seem to appear first on PCI
*/
if (chip->type == macio_gatwick || chip->type == macio_ohareII)
if (macio_chips[0].lbus.pdev == NULL) {
^ permalink raw reply
* [PATCH] powerpc: Add back support for booting from BootX (#2)
From: Benjamin Herrenschmidt @ 2005-11-23 6:58 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc64-dev, linuxppc-dev list
ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Index: linux-serialfix/arch/powerpc/platforms/powermac/bootx_init.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/platforms/powermac/bootx_init.c 2005-11-23 16:54:26.000000000 +1100
@@ -0,0 +1,547 @@
+/*
+ * Early boot support code for BootX bootloader
+ *
+ * Copyright (C) 2005 Ben. Herrenschmidt (benh@kernel.crashing.org)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/init.h>
+#include <linux/version.h>
+#include <asm/sections.h>
+#include <asm/prom.h>
+#include <asm/page.h>
+#include <asm/bootx.h>
+#include <asm/bootinfo.h>
+#include <asm/btext.h>
+#include <asm/io.h>
+
+#undef DEBUG
+#define SET_BOOT_BAT
+
+#ifdef DEBUG
+#define DBG(fmt...) do { bootx_printf(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+extern void __start(unsigned long r3, unsigned long r4, unsigned long r5);
+
+static unsigned long __initdata bootx_dt_strbase;
+static unsigned long __initdata bootx_dt_strend;
+static unsigned long __initdata bootx_node_chosen;
+static boot_infos_t * __initdata bootx_info;
+static char __initdata bootx_disp_path[256];
+
+/* Is boot-info compatible ? */
+#define BOOT_INFO_IS_COMPATIBLE(bi) \
+ ((bi)->compatible_version <= BOOT_INFO_VERSION)
+#define BOOT_INFO_IS_V2_COMPATIBLE(bi) ((bi)->version >= 2)
+#define BOOT_INFO_IS_V4_COMPATIBLE(bi) ((bi)->version >= 4)
+
+#ifdef CONFIG_BOOTX_TEXT
+static void __init bootx_printf(const char *format, ...)
+{
+ const char *p, *q, *s;
+ va_list args;
+ unsigned long v;
+
+ va_start(args, format);
+ for (p = format; *p != 0; p = q) {
+ for (q = p; *q != 0 && *q != '\n' && *q != '%'; ++q)
+ ;
+ if (q > p)
+ btext_drawtext(p, q - p);
+ if (*q == 0)
+ break;
+ if (*q == '\n') {
+ ++q;
+ btext_flushline();
+ btext_drawstring("\r\n");
+ btext_flushline();
+ continue;
+ }
+ ++q;
+ if (*q == 0)
+ break;
+ switch (*q) {
+ case 's':
+ ++q;
+ s = va_arg(args, const char *);
+ if (s == NULL)
+ s = "<NULL>";
+ btext_drawstring(s);
+ break;
+ case 'x':
+ ++q;
+ v = va_arg(args, unsigned long);
+ btext_drawhex(v);
+ break;
+ }
+ }
+}
+#else /* CONFIG_BOOTX_TEXT */
+static void __init bootx_printf(const char *format, ...) {}
+#endif /* CONFIG_BOOTX_TEXT */
+
+static void * __init bootx_early_getprop(unsigned long base,
+ unsigned long node,
+ char *prop)
+{
+ struct bootx_dt_node *np = (struct bootx_dt_node *)(base + node);
+ u32 *ppp = &np->properties;
+
+ while(*ppp) {
+ struct bootx_dt_prop *pp =
+ (struct bootx_dt_prop *)(base + *ppp);
+
+ if (strcmp((char *)((unsigned long)pp->name + base),
+ prop) == 0) {
+ return (void *)((unsigned long)pp->value + base);
+ }
+ ppp = &pp->next;
+ }
+ return NULL;
+}
+
+#define dt_push_token(token, mem) \
+ do { \
+ *(mem) = _ALIGN_UP(*(mem),4); \
+ *((u32 *)*(mem)) = token; \
+ *(mem) += 4; \
+ } while(0)
+
+static unsigned long __init bootx_dt_find_string(char *str)
+{
+ char *s, *os;
+
+ s = os = (char *)bootx_dt_strbase;
+ s += 4;
+ while (s < (char *)bootx_dt_strend) {
+ if (strcmp(s, str) == 0)
+ return s - os;
+ s += strlen(s) + 1;
+ }
+ return 0;
+}
+
+static void __init bootx_dt_add_prop(char *name, void *data, int size,
+ unsigned long *mem_end)
+{
+ unsigned long soff = bootx_dt_find_string(name);
+ if (data == NULL)
+ size = 0;
+ if (soff == 0) {
+ bootx_printf("WARNING: Can't find string index for <%s>\n",
+ name);
+ return;
+ }
+ if (size > 0x20000) {
+ bootx_printf("WARNING: ignoring large property ");
+ bootx_printf("%s length 0x%x\n", name, size);
+ return;
+ }
+ dt_push_token(OF_DT_PROP, mem_end);
+ dt_push_token(size, mem_end);
+ dt_push_token(soff, mem_end);
+
+ /* push property content */
+ if (size && data) {
+ memcpy((void *)*mem_end, data, size);
+ *mem_end = _ALIGN_UP(*mem_end + size, 4);
+ }
+}
+
+static void __init bootx_add_chosen_props(unsigned long base,
+ unsigned long *mem_end)
+{
+ u32 val = _MACH_Pmac;
+
+ bootx_dt_add_prop("linux,platform", &val, 4, mem_end);
+
+ if (bootx_info->kernelParamsOffset) {
+ char *args = (char *)((unsigned long)bootx_info) +
+ bootx_info->kernelParamsOffset;
+ bootx_dt_add_prop("bootargs", args, strlen(args) + 1, mem_end);
+ }
+ if (bootx_info->ramDisk) {
+ val = ((unsigned long)bootx_info) + bootx_info->ramDisk;
+ bootx_dt_add_prop("linux,initrd-start", &val, 4, mem_end);
+ val += bootx_info->ramDiskSize;
+ bootx_dt_add_prop("linux,initrd-end", &val, 4, mem_end);
+ }
+ if (strlen(bootx_disp_path))
+ bootx_dt_add_prop("linux,stdout-path", bootx_disp_path,
+ strlen(bootx_disp_path) + 1, mem_end);
+}
+
+static void __init bootx_add_display_props(unsigned long base,
+ unsigned long *mem_end)
+{
+ bootx_dt_add_prop("linux,boot-display", NULL, 0, mem_end);
+ bootx_dt_add_prop("linux,opened", NULL, 0, mem_end);
+}
+
+static void __init bootx_dt_add_string(char *s, unsigned long *mem_end)
+{
+ unsigned int l = strlen(s) + 1;
+ memcpy((void *)*mem_end, s, l);
+ bootx_dt_strend = *mem_end = *mem_end + l;
+}
+
+static void __init bootx_scan_dt_build_strings(unsigned long base,
+ unsigned long node,
+ unsigned long *mem_end)
+{
+ struct bootx_dt_node *np = (struct bootx_dt_node *)(base + node);
+ u32 *cpp, *ppp = &np->properties;
+ unsigned long soff;
+ char *namep;
+
+ /* Keep refs to known nodes */
+ namep = np->full_name ? (char *)(base + np->full_name) : NULL;
+ if (namep == NULL) {
+ bootx_printf("Node without a full name !\n");
+ namep = "";
+ }
+ DBG("* strings: %s\n", namep);
+
+ if (!strcmp(namep, "/chosen")) {
+ DBG(" detected /chosen ! adding properties names !\n");
+ bootx_dt_add_string("linux,platform", mem_end);
+ bootx_dt_add_string("linux,stdout-path", mem_end);
+ bootx_dt_add_string("linux,initrd-start", mem_end);
+ bootx_dt_add_string("linux,initrd-end", mem_end);
+ bootx_dt_add_string("bootargs", mem_end);
+ bootx_node_chosen = node;
+ }
+ if (node == bootx_info->dispDeviceRegEntryOffset) {
+ DBG(" detected display ! adding properties names !\n");
+ bootx_dt_add_string("linux,boot-display", mem_end);
+ bootx_dt_add_string("linux,opened", mem_end);
+ strncpy(bootx_disp_path, namep, 255);
+ }
+
+ /* get and store all property names */
+ while (*ppp) {
+ struct bootx_dt_prop *pp =
+ (struct bootx_dt_prop *)(base + *ppp);
+
+ namep = pp->name ? (char *)(base + pp->name) : NULL;
+ if (namep == NULL || strcmp(namep, "name") == 0)
+ goto next;
+ /* get/create string entry */
+ soff = bootx_dt_find_string(namep);
+ if (soff == 0)
+ bootx_dt_add_string(namep, mem_end);
+ next:
+ ppp = &pp->next;
+ }
+
+ /* do all our children */
+ cpp = &np->child;
+ while(*cpp) {
+ np = (struct bootx_dt_node *)(base + *cpp);
+ bootx_scan_dt_build_strings(base, *cpp, mem_end);
+ cpp = &np->sibling;
+ }
+}
+
+static void __init bootx_scan_dt_build_struct(unsigned long base,
+ unsigned long node,
+ unsigned long *mem_end)
+{
+ struct bootx_dt_node *np = (struct bootx_dt_node *)(base + node);
+ u32 *cpp, *ppp = &np->properties;
+ char *namep, *p, *ep, *lp;
+ int l;
+
+ dt_push_token(OF_DT_BEGIN_NODE, mem_end);
+
+ /* get the node's full name */
+ namep = np->full_name ? (char *)(base + np->full_name) : NULL;
+ if (namep == NULL)
+ namep = "";
+ l = strlen(namep);
+
+ DBG("* struct: %s\n", namep);
+
+ /* Fixup an Apple bug where they have bogus \0 chars in the
+ * middle of the path in some properties, and extract
+ * the unit name (everything after the last '/').
+ */
+ memcpy((void *)*mem_end, namep, l + 1);
+ namep = (char *)*mem_end;
+ for (lp = p = namep, ep = namep + l; p < ep; p++) {
+ if (*p == '/')
+ lp = namep;
+ else if (*p != 0)
+ *lp++ = *p;
+ }
+ *lp = 0;
+ *mem_end = _ALIGN_UP((unsigned long)lp + 1, 4);
+
+ /* get and store all properties */
+ while (*ppp) {
+ struct bootx_dt_prop *pp =
+ (struct bootx_dt_prop *)(base + *ppp);
+
+ namep = pp->name ? (char *)(base + pp->name) : NULL;
+ /* Skip "name" */
+ if (namep == NULL || !strcmp(namep, "name"))
+ goto next;
+ /* Skip "bootargs" in /chosen too as we replace it */
+ if (node == bootx_node_chosen && !strcmp(namep, "bootargs"))
+ goto next;
+
+ /* push property head */
+ bootx_dt_add_prop(namep,
+ pp->value ? (void *)(base + pp->value): NULL,
+ pp->length, mem_end);
+ next:
+ ppp = &pp->next;
+ }
+
+ if (node == bootx_node_chosen)
+ bootx_add_chosen_props(base, mem_end);
+ if (node == bootx_info->dispDeviceRegEntryOffset)
+ bootx_add_display_props(base, mem_end);
+
+ /* do all our children */
+ cpp = &np->child;
+ while(*cpp) {
+ np = (struct bootx_dt_node *)(base + *cpp);
+ bootx_scan_dt_build_struct(base, *cpp, mem_end);
+ cpp = &np->sibling;
+ }
+
+ dt_push_token(OF_DT_END_NODE, mem_end);
+}
+
+static unsigned long __init bootx_flatten_dt(unsigned long start)
+{
+ boot_infos_t *bi = bootx_info;
+ unsigned long mem_start, mem_end;
+ struct boot_param_header *hdr;
+ unsigned long base;
+ u64 *rsvmap;
+
+ /* Start using memory after the big blob passed by BootX, get
+ * some space for the header
+ */
+ mem_start = mem_end = _ALIGN_UP(((unsigned long)bi) + start, 4);
+ DBG("Boot params header at: %x\n", mem_start);
+ hdr = (struct boot_param_header *)mem_start;
+ mem_end += sizeof(struct boot_param_header);
+ rsvmap = (u64 *)(_ALIGN_UP(mem_end, 8));
+ hdr->off_mem_rsvmap = ((unsigned long)rsvmap) - mem_start;
+ mem_end = ((unsigned long)rsvmap) + 8 * sizeof(u64);
+
+ /* Get base of tree */
+ base = ((unsigned long)bi) + bi->deviceTreeOffset;
+
+ /* Build string array */
+ DBG("Building string array at: %x\n", mem_end);
+ DBG("Device Tree Base=%x\n", base);
+ bootx_dt_strbase = mem_end;
+ mem_end += 4;
+ bootx_dt_strend = mem_end;
+ bootx_scan_dt_build_strings(base, 4, &mem_end);
+ hdr->off_dt_strings = bootx_dt_strbase - mem_start;
+ hdr->dt_strings_size = bootx_dt_strend - bootx_dt_strbase;
+
+ /* Build structure */
+ mem_end = _ALIGN(mem_end, 16);
+ DBG("Building device tree structure at: %x\n", mem_end);
+ hdr->off_dt_struct = mem_end - mem_start;
+ bootx_scan_dt_build_struct(base, 4, &mem_end);
+ dt_push_token(OF_DT_END, &mem_end);
+
+ /* Finish header */
+ hdr->boot_cpuid_phys = 0;
+ hdr->magic = OF_DT_HEADER;
+ hdr->totalsize = mem_end - mem_start;
+ hdr->version = OF_DT_VERSION;
+ /* Version 16 is not backward compatible */
+ hdr->last_comp_version = 0x10;
+
+ /* Reserve the whole thing and copy the reserve map in, we
+ * also bump mem_reserve_cnt to cause further reservations to
+ * fail since it's too late.
+ */
+ mem_end = _ALIGN(mem_end, PAGE_SIZE);
+ DBG("End of boot params: %x\n", mem_end);
+ rsvmap[0] = mem_start;
+ rsvmap[1] = mem_end;
+ rsvmap[2] = 0;
+ rsvmap[3] = 0;
+
+ return (unsigned long)hdr;
+}
+
+
+#ifdef CONFIG_BOOTX_TEXT
+static void __init btext_welcome(boot_infos_t *bi)
+{
+ unsigned long flags;
+ unsigned long pvr;
+
+ bootx_printf("Welcome to Linux, kernel " UTS_RELEASE "\n");
+ bootx_printf("\nlinked at : 0x%x", KERNELBASE);
+ bootx_printf("\nframe buffer at : 0x%x", bi->dispDeviceBase);
+ bootx_printf(" (phys), 0x%x", bi->logicalDisplayBase);
+ bootx_printf(" (log)");
+ bootx_printf("\nklimit : 0x%x",(unsigned long)klimit);
+ bootx_printf("\nboot_info at : 0x%x", bi);
+ __asm__ __volatile__ ("mfmsr %0" : "=r" (flags));
+ bootx_printf("\nMSR : 0x%x", flags);
+ __asm__ __volatile__ ("mfspr %0, 287" : "=r" (pvr));
+ bootx_printf("\nPVR : 0x%x", pvr);
+ pvr >>= 16;
+ if (pvr > 1) {
+ __asm__ __volatile__ ("mfspr %0, 1008" : "=r" (flags));
+ bootx_printf("\nHID0 : 0x%x", flags);
+ }
+ if (pvr == 8 || pvr == 12 || pvr == 0x800c) {
+ __asm__ __volatile__ ("mfspr %0, 1019" : "=r" (flags));
+ bootx_printf("\nICTC : 0x%x", flags);
+ }
+#ifdef DEBUG
+ bootx_printf("\n\n");
+ bootx_printf("bi->deviceTreeOffset : 0x%x\n",
+ bi->deviceTreeOffset);
+ bootx_printf("bi->deviceTreeSize : 0x%x\n",
+ bi->deviceTreeSize);
+#endif
+ bootx_printf("\n\n");
+}
+#endif /* CONFIG_BOOTX_TEXT */
+
+void __init bootx_init(unsigned long r3, unsigned long r4)
+{
+ boot_infos_t *bi = (boot_infos_t *) r4;
+ unsigned long hdr;
+ unsigned long space;
+ unsigned long ptr, x;
+ char *model;
+ unsigned long offset = reloc_offset();
+
+ reloc_got2(offset);
+
+ bootx_info = bi;
+
+ /* We haven't cleared any bss at this point, make sure
+ * what we need is initialized
+ */
+ bootx_dt_strbase = bootx_dt_strend = 0;
+ bootx_node_chosen = 0;
+ bootx_disp_path[0] = 0;
+
+ if (!BOOT_INFO_IS_V2_COMPATIBLE(bi))
+ bi->logicalDisplayBase = bi->dispDeviceBase;
+
+#ifdef CONFIG_BOOTX_TEXT
+ btext_setup_display(bi->dispDeviceRect[2] - bi->dispDeviceRect[0],
+ bi->dispDeviceRect[3] - bi->dispDeviceRect[1],
+ bi->dispDeviceDepth, bi->dispDeviceRowBytes,
+ (unsigned long)bi->logicalDisplayBase);
+ btext_clearscreen();
+ btext_flushscreen();
+#endif /* CONFIG_BOOTX_TEXT */
+
+ /*
+ * Test if boot-info is compatible. Done only in config
+ * CONFIG_BOOTX_TEXT since there is nothing much we can do
+ * with an incompatible version, except display a message
+ * and eventually hang the processor...
+ *
+ * I'll try to keep enough of boot-info compatible in the
+ * future to always allow display of this message;
+ */
+ if (!BOOT_INFO_IS_COMPATIBLE(bi)) {
+ bootx_printf(" !!! WARNING - Incompatible version"
+ " of BootX !!!\n\n\n");
+ for (;;)
+ ;
+ }
+ if (bi->architecture != BOOT_ARCH_PCI) {
+ bootx_printf(" !!! WARNING - Usupported machine"
+ " architecture !\n");
+ for (;;)
+ ;
+ }
+
+#ifdef CONFIG_BOOTX_TEXT
+ btext_welcome(bi);
+#endif
+ /* New BootX enters kernel with MMU off, i/os are not allowed
+ * here. This hack will have been done by the boostrap anyway.
+ */
+ if (bi->version < 4) {
+ /*
+ * XXX If this is an iMac, turn off the USB controller.
+ */
+ model = (char *) bootx_early_getprop(r4 + bi->deviceTreeOffset,
+ 4, "model");
+ if (model
+ && (strcmp(model, "iMac,1") == 0
+ || strcmp(model, "PowerMac1,1") == 0)) {
+ bootx_printf("iMac,1 detected, shutting down USB \n");
+ out_le32((unsigned *)0x80880008, 1); /* XXX */
+ }
+ }
+
+ /* Get a pointer that points above the device tree, args, ramdisk,
+ * etc... to use for generating the flattened tree
+ */
+ if (bi->version < 5) {
+ space = bi->deviceTreeOffset + bi->deviceTreeSize;
+ if (bi->ramDisk)
+ space = bi->ramDisk + bi->ramDiskSize;
+ } else
+ space = bi->totalParamsSize;
+
+ bootx_printf("Total space used by parameters & ramdisk: %x \n", space);
+
+ /* New BootX will have flushed all TLBs and enters kernel with
+ * MMU switched OFF, so this should not be useful anymore.
+ */
+ if (bi->version < 4) {
+ bootx_printf("Touching pages...\n");
+
+ /*
+ * Touch each page to make sure the PTEs for them
+ * are in the hash table - the aim is to try to avoid
+ * getting DSI exceptions while copying the kernel image.
+ */
+ for (ptr = ((unsigned long) &_stext) & PAGE_MASK;
+ ptr < (unsigned long)bi + space; ptr += PAGE_SIZE)
+ x = *(volatile unsigned long *)ptr;
+ }
+
+ /* Ok, now we need to generate a flattened device-tree to pass
+ * to the kernel
+ */
+ bootx_printf("Preparing boot params...\n");
+
+ hdr = bootx_flatten_dt(space);
+
+#ifdef CONFIG_BOOTX_TEXT
+#ifdef SET_BOOT_BAT
+ bootx_printf("Preparing BAT...\n");
+ btext_prepare_BAT();
+#else
+ btext_unmap();
+#endif
+#endif
+
+ reloc_got2(-offset);
+
+ __start(hdr, KERNELBASE + offset, 0);
+}
Index: linux-serialfix/arch/powerpc/kernel/head_32.S
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/head_32.S 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/head_32.S 2005-11-23 16:54:26.000000000 +1100
@@ -125,6 +125,19 @@ __start:
bl prom_init
trap
+/*
+ * Check for BootX signature when supporting PowerMac and branch to
+ * appropriate trampoline if it's present
+ */
+#ifdef CONFIG_PPC_PMAC
+1: lis r31,0x426f
+ ori r31,r31,0x6f58
+ cmpw 0,r3,r31
+ bne 1f
+ bl bootx_init
+ trap
+#endif /* CONFIG_PPC_PMAC */
+
1: mr r31,r3 /* save parameters */
mr r30,r4
li r24,0 /* cpu # */
Index: linux-serialfix/arch/powerpc/platforms/powermac/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/Makefile 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/Makefile 2005-11-23 16:54:26.000000000 +1100
@@ -1,3 +1,5 @@
+CFLAGS_bootx_init.o += -fPIC
+
obj-y += pic.o setup.o time.o feature.o pci.o \
sleep.o low_i2c.o cache.o
obj-$(CONFIG_PMAC_BACKLIGHT) += backlight.o
@@ -6,5 +8,6 @@ obj-$(CONFIG_CPU_FREQ_PMAC64) += cpufreq
obj-$(CONFIG_NVRAM) += nvram.o
# ppc64 pmac doesn't define CONFIG_NVRAM but needs nvram stuff
obj-$(CONFIG_PPC64) += nvram.o
+obj-$(CONFIG_PPC32) += bootx_init.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_PPC_MERGE) += udbg_scc.o udbg_adb.o
Index: linux-serialfix/include/asm-powerpc/bootx.h
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/include/asm-powerpc/bootx.h 2005-11-23 16:54:26.000000000 +1100
@@ -0,0 +1,166 @@
+/*
+ * This file describes the structure passed from the BootX application
+ * (for MacOS) when it is used to boot Linux.
+ *
+ * Written by Benjamin Herrenschmidt.
+ */
+
+
+#ifndef __ASM_BOOTX_H__
+#define __ASM_BOOTX_H__
+
+#ifdef macintosh
+#include <Types.h>
+#include "linux_type_defs.h"
+#endif
+
+#ifdef macintosh
+/* All this requires PowerPC alignment */
+#pragma options align=power
+#endif
+
+/* On kernel entry:
+ *
+ * r3 = 0x426f6f58 ('BooX')
+ * r4 = pointer to boot_infos
+ * r5 = NULL
+ *
+ * Data and instruction translation disabled, interrupts
+ * disabled, kernel loaded at physical 0x00000000 on PCI
+ * machines (will be different on NuBus).
+ */
+
+#define BOOT_INFO_VERSION 5
+#define BOOT_INFO_COMPATIBLE_VERSION 1
+
+/* Bit in the architecture flag mask. More to be defined in
+ future versions. Note that either BOOT_ARCH_PCI or
+ BOOT_ARCH_NUBUS is set. The other BOOT_ARCH_NUBUS_xxx are
+ set additionally when BOOT_ARCH_NUBUS is set.
+ */
+#define BOOT_ARCH_PCI 0x00000001UL
+#define BOOT_ARCH_NUBUS 0x00000002UL
+#define BOOT_ARCH_NUBUS_PDM 0x00000010UL
+#define BOOT_ARCH_NUBUS_PERFORMA 0x00000020UL
+#define BOOT_ARCH_NUBUS_POWERBOOK 0x00000040UL
+
+/* Maximum number of ranges in phys memory map */
+#define MAX_MEM_MAP_SIZE 26
+
+/* This is the format of an element in the physical memory map. Note that
+ the map is optional and current BootX will only build it for pre-PCI
+ machines */
+typedef struct boot_info_map_entry
+{
+ __u32 physAddr; /* Physical starting address */
+ __u32 size; /* Size in bytes */
+} boot_info_map_entry_t;
+
+
+/* Here are the boot informations that are passed to the bootstrap
+ * Note that the kernel arguments and the device tree are appended
+ * at the end of this structure. */
+typedef struct boot_infos
+{
+ /* Version of this structure */
+ __u32 version;
+ /* backward compatible down to version: */
+ __u32 compatible_version;
+
+ /* NEW (vers. 2) this holds the current _logical_ base addr of
+ the frame buffer (for use by early boot message) */
+ __u8* logicalDisplayBase;
+
+ /* NEW (vers. 4) Apple's machine identification */
+ __u32 machineID;
+
+ /* NEW (vers. 4) Detected hw architecture */
+ __u32 architecture;
+
+ /* The device tree (internal addresses relative to the beginning of the tree,
+ * device tree offset relative to the beginning of this structure).
+ * On pre-PCI macintosh (BOOT_ARCH_PCI bit set to 0 in architecture), this
+ * field is 0.
+ */
+ __u32 deviceTreeOffset; /* Device tree offset */
+ __u32 deviceTreeSize; /* Size of the device tree */
+
+ /* Some infos about the current MacOS display */
+ __u32 dispDeviceRect[4]; /* left,top,right,bottom */
+ __u32 dispDeviceDepth; /* (8, 16 or 32) */
+ __u8* dispDeviceBase; /* base address (physical) */
+ __u32 dispDeviceRowBytes; /* rowbytes (in bytes) */
+ __u32 dispDeviceColorsOffset; /* Colormap (8 bits only) or 0 (*) */
+ /* Optional offset in the registry to the current
+ * MacOS display. (Can be 0 when not detected) */
+ __u32 dispDeviceRegEntryOffset;
+
+ /* Optional pointer to boot ramdisk (offset from this structure) */
+ __u32 ramDisk;
+ __u32 ramDiskSize; /* size of ramdisk image */
+
+ /* Kernel command line arguments (offset from this structure) */
+ __u32 kernelParamsOffset;
+
+ /* ALL BELOW NEW (vers. 4) */
+
+ /* This defines the physical memory. Valid with BOOT_ARCH_NUBUS flag
+ (non-PCI) only. On PCI, memory is contiguous and it's size is in the
+ device-tree. */
+ boot_info_map_entry_t
+ physMemoryMap[MAX_MEM_MAP_SIZE]; /* Where the phys memory is */
+ __u32 physMemoryMapSize; /* How many entries in map */
+
+
+ /* The framebuffer size (optional, currently 0) */
+ __u32 frameBufferSize; /* Represents a max size, can be 0. */
+
+ /* NEW (vers. 5) */
+
+ /* Total params size (args + colormap + device tree + ramdisk) */
+ __u32 totalParamsSize;
+
+} boot_infos_t;
+
+/* (*) The format of the colormap is 256 * 3 * 2 bytes. Each color index
+ * is represented by 3 short words containing a 16 bits (unsigned) color
+ * component. Later versions may contain the gamma table for direct-color
+ * devices here.
+ */
+#define BOOTX_COLORTABLE_SIZE (256UL*3UL*2UL)
+
+/* BootX passes the device-tree using a format that comes from earlier
+ * ppc32 kernels. This used to match what is in prom.h, but not anymore
+ * so we now define it here
+ */
+struct bootx_dt_prop {
+ u32 name;
+ int length;
+ u32 value;
+ u32 next;
+};
+
+struct bootx_dt_node {
+ u32 unused0;
+ u32 unused1;
+ u32 phandle; /* not really available */
+ u32 unused2;
+ u32 unused3;
+ u32 unused4;
+ u32 unused5;
+ u32 full_name;
+ u32 properties;
+ u32 parent;
+ u32 child;
+ u32 sibling;
+ u32 next;
+ u32 allnext;
+};
+
+extern void bootx_init(unsigned long r4, unsigned long phys);
+
+#ifdef macintosh
+#pragma options align=reset
+#endif
+
+#endif
^ permalink raw reply
* [PATCH] powerpc: Unify udbg (#2)
From: Benjamin Herrenschmidt @ 2005-11-23 6:57 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc64-dev, linuxppc-dev list
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Updated to match the changes in prom_parse.c
Index: linux-serialfix/arch/powerpc/kernel/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/Makefile 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/Makefile 2005-11-23 16:54:25.000000000 +1100
@@ -18,7 +18,7 @@ obj-y += vdso32/
obj-$(CONFIG_PPC64) += setup_64.o binfmt_elf32.o sys_ppc32.o \
signal_64.o ptrace32.o systbl.o \
paca.o ioctl32.o cpu_setup_power4.o \
- firmware.o sysfs.o udbg.o idle_64.o
+ firmware.o sysfs.o idle_64.o
obj-$(CONFIG_PPC64) += vdso64/
obj-$(CONFIG_ALTIVEC) += vecemu.o vector.o
obj-$(CONFIG_POWER4) += idle_power4.o
@@ -45,7 +45,7 @@ extra-$(CONFIG_8xx) := head_8xx.o
extra-y += vmlinux.lds
obj-y += process.o init_task.o time.o \
- prom.o traps.o setup-common.o
+ prom.o traps.o setup-common.o udbg.o
obj-$(CONFIG_PPC32) += entry_32.o setup_32.o misc_32.o systbl.o
obj-$(CONFIG_PPC64) += misc_64.o dma_64.o iommu.o
obj-$(CONFIG_PPC_OF) += prom_init.o
@@ -55,8 +55,7 @@ obj-$(CONFIG_6xx) += idle_6xx.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_KPROBES) += kprobes.o
obj-$(CONFIG_PPC_MULTIPLATFORM) += legacy_serial.o
-obj64-$(CONFIG_PPC_MULTIPLATFORM) += udbg_16550.o
-obj64-$(CONFIG_PPC_PMAC) += udbg_scc.o
+obj-$(CONFIG_PPC_MULTIPLATFORM) += udbg_16550.o
module-$(CONFIG_PPC64) += module_64.o
obj-$(CONFIG_MODULES) += $(module-y)
Index: linux-serialfix/arch/powerpc/kernel/udbg.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/udbg.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/udbg.c 2005-11-23 16:54:25.000000000 +1100
@@ -16,8 +16,8 @@
#include <linux/console.h>
#include <asm/processor.h>
-void (*udbg_putc)(unsigned char c);
-unsigned char (*udbg_getc)(void);
+void (*udbg_putc)(char c);
+char (*udbg_getc)(void);
int (*udbg_getc_poll)(void);
/* udbg library, used by xmon et al */
@@ -78,7 +78,7 @@ int udbg_read(char *buf, int buflen)
#define UDBG_BUFSIZE 256
void udbg_printf(const char *fmt, ...)
{
- unsigned char buf[UDBG_BUFSIZE];
+ char buf[UDBG_BUFSIZE];
va_list args;
va_start(args, fmt);
@@ -116,6 +116,8 @@ void __init disable_early_printk(void)
/* called by setup_system */
void register_early_udbg_console(void)
{
+ if (early_console_initialized)
+ return;
early_console_initialized = 1;
register_console(&udbg_console);
}
Index: linux-serialfix/arch/powerpc/kernel/udbg_scc.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/udbg_scc.c 2005-11-23 16:54:13.000000000 +1100
+++ /dev/null 1970-01-01 00:00:00.000000000 +0000
@@ -1,135 +0,0 @@
-/*
- * udbg for for zilog scc ports as found on Apple PowerMacs
- *
- * Copyright (C) 2001-2005 PPC 64 Team, IBM Corp
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#include <linux/config.h>
-#include <linux/types.h>
-#include <asm/udbg.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include <asm/prom.h>
-#include <asm/pmac_feature.h>
-
-extern u8 real_readb(volatile u8 __iomem *addr);
-extern void real_writeb(u8 data, volatile u8 __iomem *addr);
-
-#define SCC_TXRDY 4
-#define SCC_RXRDY 1
-
-static volatile u8 __iomem *sccc;
-static volatile u8 __iomem *sccd;
-
-static void udbg_scc_putc(unsigned char c)
-{
- if (sccc) {
- while ((in_8(sccc) & SCC_TXRDY) == 0)
- ;
- out_8(sccd, c);
- if (c == '\n')
- udbg_scc_putc('\r');
- }
-}
-
-static int udbg_scc_getc_poll(void)
-{
- if (sccc) {
- if ((in_8(sccc) & SCC_RXRDY) != 0)
- return in_8(sccd);
- else
- return -1;
- }
- return -1;
-}
-
-static unsigned char udbg_scc_getc(void)
-{
- if (sccc) {
- while ((in_8(sccc) & SCC_RXRDY) == 0)
- ;
- return in_8(sccd);
- }
- return 0;
-}
-
-static unsigned char scc_inittab[] = {
- 13, 0, /* set baud rate divisor */
- 12, 0,
- 14, 1, /* baud rate gen enable, src=rtxc */
- 11, 0x50, /* clocks = br gen */
- 5, 0xea, /* tx 8 bits, assert DTR & RTS */
- 4, 0x46, /* x16 clock, 1 stop */
- 3, 0xc1, /* rx enable, 8 bits */
-};
-
-void udbg_init_scc(struct device_node *np)
-{
- u32 *reg;
- unsigned long addr;
- int i, x;
-
- if (np == NULL)
- np = of_find_node_by_name(NULL, "escc");
- if (np == NULL || np->parent == NULL)
- return;
-
- udbg_printf("found SCC...\n");
- /* Get address within mac-io ASIC */
- reg = (u32 *)get_property(np, "reg", NULL);
- if (reg == NULL)
- return;
- addr = reg[0];
- udbg_printf("local addr: %lx\n", addr);
- /* Get address of mac-io PCI itself */
- reg = (u32 *)get_property(np->parent, "assigned-addresses", NULL);
- if (reg == NULL)
- return;
- addr += reg[2];
- udbg_printf("final addr: %lx\n", addr);
-
- /* Setup for 57600 8N1 */
- addr += 0x20;
- sccc = (volatile u8 * __iomem) ioremap(addr & PAGE_MASK, PAGE_SIZE) ;
- sccc += addr & ~PAGE_MASK;
- sccd = sccc + 0x10;
-
- udbg_printf("ioremap result sccc: %p\n", sccc);
- mb();
-
- for (i = 20000; i != 0; --i)
- x = in_8(sccc);
- out_8(sccc, 0x09); /* reset A or B side */
- out_8(sccc, 0xc0);
- for (i = 0; i < sizeof(scc_inittab); ++i)
- out_8(sccc, scc_inittab[i]);
-
- udbg_putc = udbg_scc_putc;
- udbg_getc = udbg_scc_getc;
- udbg_getc_poll = udbg_scc_getc_poll;
-
- udbg_puts("Hello World !\n");
-}
-
-static void udbg_real_scc_putc(unsigned char c)
-{
- while ((real_readb(sccc) & SCC_TXRDY) == 0)
- ;
- real_writeb(c, sccd);
- if (c == '\n')
- udbg_real_scc_putc('\r');
-}
-
-void udbg_init_pmac_realmode(void)
-{
- sccc = (volatile u8 __iomem *)0x80013020ul;
- sccd = (volatile u8 __iomem *)0x80013030ul;
-
- udbg_putc = udbg_real_scc_putc;
- udbg_getc = NULL;
- udbg_getc_poll = NULL;
-}
Index: linux-serialfix/arch/powerpc/platforms/powermac/udbg_adb.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/platforms/powermac/udbg_adb.c 2005-11-23 16:54:25.000000000 +1100
@@ -0,0 +1,218 @@
+#include <linux/config.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/bitops.h>
+#include <linux/ptrace.h>
+#include <linux/adb.h>
+#include <linux/pmu.h>
+#include <linux/cuda.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/page.h>
+#include <asm/xmon.h>
+#include <asm/prom.h>
+#include <asm/bootx.h>
+#include <asm/machdep.h>
+#include <asm/errno.h>
+#include <asm/pmac_feature.h>
+#include <asm/processor.h>
+#include <asm/delay.h>
+#include <asm/btext.h>
+#include <asm/time.h>
+#include <asm/udbg.h>
+
+/*
+ * This implementation is "special", it can "patch" the current
+ * udbg implementation and work on top of it. It must thus be
+ * initialized last
+ */
+
+static void (*udbg_adb_old_putc)(char c);
+static char (*udbg_adb_old_getc)(void);
+static int (*udbg_adb_old_getc_poll)(void);
+
+static enum {
+ input_adb_none,
+ input_adb_pmu,
+ input_adb_cuda,
+} input_type = input_adb_none;
+
+static int udbg_adb_use_btext;
+
+int xmon_wants_key, xmon_adb_keycode;
+
+static inline void udbg_adb_poll(void)
+{
+#ifdef CONFIG_ADB_PMU
+ if (input_type == input_adb_pmu)
+ pmu_poll_adb();
+#endif /* CONFIG_ADB_PMU */
+#ifdef CONFIG_ADB_CUDA
+ if (input_type == input_adb_cuda)
+ cuda_poll();
+#endif /* CONFIG_ADB_CUDA */
+}
+
+#ifdef CONFIG_BOOTX_TEXT
+static int xmon_adb_shiftstate;
+
+static unsigned char xmon_keytab[128] =
+ "asdfhgzxcv\000bqwer" /* 0x00 - 0x0f */
+ "yt123465=97-80]o" /* 0x10 - 0x1f */
+ "u[ip\rlj'k;\\,/nm." /* 0x20 - 0x2f */
+ "\t `\177\0\033\0\0\0\0\0\0\0\0\0\0" /* 0x30 - 0x3f */
+ "\0.\0*\0+\0\0\0\0\0/\r\0-\0" /* 0x40 - 0x4f */
+ "\0\0000123456789\0\0\0"; /* 0x50 - 0x5f */
+
+static unsigned char xmon_shift_keytab[128] =
+ "ASDFHGZXCV\000BQWER" /* 0x00 - 0x0f */
+ "YT!@#$^%+(&_*)}O" /* 0x10 - 0x1f */
+ "U{IP\rLJ\"K:|<?NM>" /* 0x20 - 0x2f */
+ "\t ~\177\0\033\0\0\0\0\0\0\0\0\0\0" /* 0x30 - 0x3f */
+ "\0.\0*\0+\0\0\0\0\0/\r\0-\0" /* 0x40 - 0x4f */
+ "\0\0000123456789\0\0\0"; /* 0x50 - 0x5f */
+
+static char udbg_adb_local_getc(void)
+{
+ int k, t, on;
+
+ xmon_wants_key = 1;
+ for (;;) {
+ xmon_adb_keycode = -1;
+ t = 0;
+ on = 0;
+ k = -1;
+ do {
+ if (--t < 0) {
+ on = 1 - on;
+ btext_drawchar(on? 0xdb: 0x20);
+ btext_drawchar('\b');
+ t = 200000;
+ }
+ udbg_adb_poll();
+ if (udbg_adb_old_getc_poll)
+ k = udbg_adb_old_getc_poll();
+ } while (k == -1 && xmon_adb_keycode == -1);
+ if (on)
+ btext_drawstring(" \b");
+ if (k != -1)
+ return k;
+ k = xmon_adb_keycode;
+
+ /* test for shift keys */
+ if ((k & 0x7f) == 0x38 || (k & 0x7f) == 0x7b) {
+ xmon_adb_shiftstate = (k & 0x80) == 0;
+ continue;
+ }
+ if (k >= 0x80)
+ continue; /* ignore up transitions */
+ k = (xmon_adb_shiftstate? xmon_shift_keytab: xmon_keytab)[k];
+ if (k != 0)
+ break;
+ }
+ xmon_wants_key = 0;
+ return k;
+}
+#endif /* CONFIG_BOOTX_TEXT */
+
+static char udbg_adb_getc(void)
+{
+#ifdef CONFIG_BOOTX_TEXT
+ if (udbg_adb_use_btext && input_type != input_adb_none)
+ return udbg_adb_local_getc();
+#endif
+ if (udbg_adb_old_getc)
+ return udbg_adb_old_getc();
+ return -1;
+}
+
+/* getc_poll() is not really used, unless you have the xmon-over modem
+ * hack that doesn't quite concern us here, thus we just poll the low level
+ * ADB driver to prevent it from timing out and call back the original poll
+ * routine.
+ */
+static int udbg_adb_getc_poll(void)
+{
+ udbg_adb_poll();
+
+ if (udbg_adb_old_getc_poll)
+ return udbg_adb_old_getc_poll();
+ return -1;
+}
+
+static void udbg_adb_putc(char c)
+{
+#ifdef CONFIG_BOOTX_TEXT
+ if (udbg_adb_use_btext)
+ btext_drawchar(c);
+#endif
+ if (udbg_adb_old_putc)
+ return udbg_adb_old_putc(c);
+}
+
+void udbg_adb_init_early(void)
+{
+#ifdef CONFIG_BOOTX_TEXT
+ if (btext_find_display(1) == 0) {
+ udbg_adb_use_btext = 1;
+ udbg_putc = udbg_adb_putc;
+ }
+#endif
+}
+
+int udbg_adb_init(int force_btext)
+{
+ struct device_node *np;
+
+ /* Capture existing callbacks */
+ udbg_adb_old_putc = udbg_putc;
+ udbg_adb_old_getc = udbg_getc;
+ udbg_adb_old_getc_poll = udbg_getc_poll;
+
+ /* Check if our early init was already called */
+ if (udbg_adb_old_putc == udbg_adb_putc ||
+ udbg_adb_old_putc == btext_drawchar)
+ udbg_adb_old_putc = NULL;
+
+ /* Set ours as output */
+ udbg_putc = udbg_adb_putc;
+ udbg_getc = udbg_adb_getc;
+ udbg_getc_poll = udbg_adb_getc_poll;
+
+#ifdef CONFIG_BOOTX_TEXT
+ /* Check if we should use btext output */
+ if (btext_find_display(force_btext) == 0)
+ udbg_adb_use_btext = 1;
+#endif
+
+ /* See if there is a keyboard in the device tree with a parent
+ * of type "adb". If not, we return a failure, but we keep the
+ * bext output set for now
+ */
+ for (np = NULL; (np = of_find_node_by_name(np, "keyboard")) != NULL;) {
+ struct device_node *parent = of_get_parent(np);
+ int found = (parent && !strcmp(parent->type, "adb") == 0);
+ of_node_put(parent);
+ if (found)
+ break;
+ }
+ if (np == NULL)
+ return -ENODEV;
+ of_node_put(np);
+
+#ifdef CONFIG_ADB_PMU
+ if (find_via_pmu())
+ input_type = input_adb_pmu;
+#endif
+#ifdef CONFIG_ADB_CUDA
+ if (find_via_cuda())
+ input_type = input_adb_cuda;
+#endif
+
+ /* Same as above: nothing found, keep btext set for output */
+ if (input_type == input_adb_none)
+ return -ENODEV;
+
+ return 0;
+}
Index: linux-serialfix/arch/powerpc/platforms/powermac/udbg_scc.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/platforms/powermac/udbg_scc.c 2005-11-23 16:54:25.000000000 +1100
@@ -0,0 +1,165 @@
+/*
+ * udbg for for zilog scc ports as found on Apple PowerMacs
+ *
+ * Copyright (C) 2001-2005 PPC 64 Team, IBM Corp
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <linux/config.h>
+#include <linux/types.h>
+#include <asm/udbg.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/prom.h>
+#include <asm/pmac_feature.h>
+
+extern u8 real_readb(volatile u8 __iomem *addr);
+extern void real_writeb(u8 data, volatile u8 __iomem *addr);
+
+#define SCC_TXRDY 4
+#define SCC_RXRDY 1
+
+static volatile u8 __iomem *sccc;
+static volatile u8 __iomem *sccd;
+
+static void udbg_scc_putc(char c)
+{
+ if (sccc) {
+ while ((in_8(sccc) & SCC_TXRDY) == 0)
+ ;
+ out_8(sccd, c);
+ if (c == '\n')
+ udbg_scc_putc('\r');
+ }
+}
+
+static int udbg_scc_getc_poll(void)
+{
+ if (sccc) {
+ if ((in_8(sccc) & SCC_RXRDY) != 0)
+ return in_8(sccd);
+ else
+ return -1;
+ }
+ return -1;
+}
+
+static char udbg_scc_getc(void)
+{
+ if (sccc) {
+ while ((in_8(sccc) & SCC_RXRDY) == 0)
+ ;
+ return in_8(sccd);
+ }
+ return 0;
+}
+
+static unsigned char scc_inittab[] = {
+ 13, 0, /* set baud rate divisor */
+ 12, 0,
+ 14, 1, /* baud rate gen enable, src=rtxc */
+ 11, 0x50, /* clocks = br gen */
+ 5, 0xea, /* tx 8 bits, assert DTR & RTS */
+ 4, 0x46, /* x16 clock, 1 stop */
+ 3, 0xc1, /* rx enable, 8 bits */
+};
+
+void udbg_scc_init(int force_scc)
+{
+ u32 *reg;
+ unsigned long addr;
+ struct device_node *stdout = NULL, *escc = NULL, *macio = NULL;
+ struct device_node *ch, *ch_def = NULL, *ch_a = NULL;
+ char *path;
+ int i, x;
+
+ escc = of_find_node_by_name(NULL, "escc");
+ if (escc == NULL)
+ goto bail;
+ macio = of_get_parent(escc);
+ if (macio == NULL)
+ goto bail;
+ path = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
+ if (path != NULL)
+ stdout = of_find_node_by_path(path);
+ for (ch = NULL; (ch = of_get_next_child(escc, ch)) != NULL;) {
+ if (ch == stdout)
+ ch_def = of_node_get(ch);
+ if (strcmp(ch->name, "ch-a") == 0)
+ ch_a = of_node_get(ch);
+ }
+ if (ch_def == NULL && !force_scc)
+ goto bail;
+
+ ch = ch_def ? ch_def : ch_a;
+
+ /* Get address within mac-io ASIC */
+ reg = (u32 *)get_property(escc, "reg", NULL);
+ if (reg == NULL)
+ goto bail;
+ addr = reg[0];
+
+ /* Get address of mac-io PCI itself */
+ reg = (u32 *)get_property(macio, "assigned-addresses", NULL);
+ if (reg == NULL)
+ goto bail;
+ addr += reg[2];
+
+ /* Lock the serial port */
+ pmac_call_feature(PMAC_FTR_SCC_ENABLE, ch,
+ PMAC_SCC_ASYNC | PMAC_SCC_FLAG_XMON, 1);
+
+
+ /* Setup for 57600 8N1 */
+ if (ch == ch_a)
+ addr += 0x20;
+ sccc = (volatile u8 * __iomem) ioremap(addr & PAGE_MASK, PAGE_SIZE) ;
+ sccc += addr & ~PAGE_MASK;
+ sccd = sccc + 0x10;
+
+ mb();
+
+ for (i = 20000; i != 0; --i)
+ x = in_8(sccc);
+ out_8(sccc, 0x09); /* reset A or B side */
+ out_8(sccc, 0xc0);
+ for (i = 0; i < sizeof(scc_inittab); ++i)
+ out_8(sccc, scc_inittab[i]);
+
+ udbg_putc = udbg_scc_putc;
+ udbg_getc = udbg_scc_getc;
+ udbg_getc_poll = udbg_scc_getc_poll;
+
+ udbg_puts("Hello World !\n");
+
+ bail:
+ of_node_put(macio);
+ of_node_put(escc);
+ of_node_put(stdout);
+ of_node_put(ch_def);
+ of_node_put(ch_a);
+}
+
+#ifdef CONFIG_PPC64
+static void udbg_real_scc_putc(char c)
+{
+ while ((real_readb(sccc) & SCC_TXRDY) == 0)
+ ;
+ real_writeb(c, sccd);
+ if (c == '\n')
+ udbg_real_scc_putc('\r');
+}
+
+void udbg_init_pmac_realmode(void)
+{
+ sccc = (volatile u8 __iomem *)0x80013020ul;
+ sccd = (volatile u8 __iomem *)0x80013030ul;
+
+ udbg_putc = udbg_real_scc_putc;
+ udbg_getc = NULL;
+ udbg_getc_poll = NULL;
+}
+#endif /* CONFIG_PPC64 */
Index: linux-serialfix/arch/powerpc/Kconfig
===================================================================
--- linux-serialfix.orig/arch/powerpc/Kconfig 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/Kconfig 2005-11-23 16:54:25.000000000 +1100
@@ -50,7 +50,7 @@ config PPC
config EARLY_PRINTK
bool
- default y if PPC64
+ default y
config COMPAT
bool
Index: linux-serialfix/arch/powerpc/kernel/btext.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/btext.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/btext.c 2005-11-23 16:54:25.000000000 +1100
@@ -31,15 +31,18 @@ static void draw_byte_32(unsigned char *
static void draw_byte_16(unsigned char *bits, unsigned int *base, int rb);
static void draw_byte_8(unsigned char *bits, unsigned int *base, int rb);
-static int g_loc_X;
-static int g_loc_Y;
-static int g_max_loc_X;
-static int g_max_loc_Y;
-
-static int dispDeviceRowBytes;
-static int dispDeviceDepth;
-static int dispDeviceRect[4];
-static unsigned char *dispDeviceBase, *logicalDisplayBase;
+#define __force_data __attribute__((__section__(".data")))
+
+static int g_loc_X __force_data;
+static int g_loc_Y __force_data;
+static int g_max_loc_X __force_data;
+static int g_max_loc_Y __force_data;
+
+static int dispDeviceRowBytes __force_data;
+static int dispDeviceDepth __force_data;
+static int dispDeviceRect[4] __force_data;
+static unsigned char *dispDeviceBase __force_data;
+static unsigned char *logicalDisplayBase __force_data;
unsigned long disp_BAT[2] __initdata = {0, 0};
@@ -47,7 +50,7 @@ unsigned long disp_BAT[2] __initdata = {
static unsigned char vga_font[cmapsz];
-int boot_text_mapped;
+int boot_text_mapped __force_data = 0;
int force_printk_to_btext = 0;
#ifdef CONFIG_PPC32
@@ -66,8 +69,7 @@ int force_printk_to_btext = 0;
* is really badly aligned, but I didn't encounter this case
* yet.
*/
-void __init
-btext_prepare_BAT(void)
+void __init btext_prepare_BAT(void)
{
unsigned long vaddr = KERNELBASE + 0x10000000;
unsigned long addr;
@@ -95,12 +97,13 @@ btext_prepare_BAT(void)
}
#endif
-/* This function will enable the early boot text when doing OF booting. This
- * way, xmon output should work too
+
+/* This function can be used to enable the early boot text when doing
+ * OF booting or within bootx init. It must be followed by a btext_unmap()
+ * call before the logical address becomes unuseable
*/
-void __init
-btext_setup_display(int width, int height, int depth, int pitch,
- unsigned long address)
+void __init btext_setup_display(int width, int height, int depth, int pitch,
+ unsigned long address)
{
g_loc_X = 0;
g_loc_Y = 0;
@@ -116,6 +119,11 @@ btext_setup_display(int width, int heigh
boot_text_mapped = 1;
}
+void __init btext_unmap(void)
+{
+ boot_text_mapped = 0;
+}
+
/* Here's a small text engine to use during early boot
* or for debugging purposes
*
@@ -127,7 +135,7 @@ btext_setup_display(int width, int heigh
* changes.
*/
-void map_boot_text(void)
+static void map_boot_text(void)
{
unsigned long base, offset, size;
unsigned char *vbase;
@@ -175,8 +183,9 @@ int btext_initialize(struct device_node
if (prop)
address = *prop;
- /* FIXME: Add support for PCI reg properties */
-
+ /* FIXME: Add support for PCI reg properties. Right now, only
+ * reliable on macs
+ */
if (address == 0)
return -EINVAL;
@@ -184,7 +193,6 @@ int btext_initialize(struct device_node
g_loc_Y = 0;
g_max_loc_X = width / 8;
g_max_loc_Y = height / 16;
- logicalDisplayBase = (unsigned char *)address;
dispDeviceBase = (unsigned char *)address;
dispDeviceRowBytes = pitch;
dispDeviceDepth = depth;
@@ -197,7 +205,7 @@ int btext_initialize(struct device_node
return 0;
}
-void __init init_boot_display(void)
+int __init btext_find_display(int allow_nonstdout)
{
char *name;
struct device_node *np = NULL;
@@ -218,8 +226,8 @@ void __init init_boot_display(void)
}
if (np)
rc = btext_initialize(np);
- if (rc == 0)
- return;
+ if (rc == 0 || !allow_nonstdout)
+ return rc;
for (np = NULL; (np = of_find_node_by_type(np, "display"));) {
if (get_property(np, "linux,opened", NULL)) {
@@ -228,8 +236,9 @@ void __init init_boot_display(void)
printk("result: %d\n", rc);
}
if (rc == 0)
- return;
+ break;
}
+ return rc;
}
/* Calc the base address of a given point (x,y) */
@@ -277,44 +286,83 @@ EXPORT_SYMBOL(btext_update_display);
void btext_clearscreen(void)
{
- unsigned long *base = (unsigned long *)calc_base(0, 0);
+ unsigned int *base = (unsigned int *)calc_base(0, 0);
unsigned long width = ((dispDeviceRect[2] - dispDeviceRect[0]) *
- (dispDeviceDepth >> 3)) >> 3;
+ (dispDeviceDepth >> 3)) >> 2;
int i,j;
for (i=0; i<(dispDeviceRect[3] - dispDeviceRect[1]); i++)
{
- unsigned long *ptr = base;
+ unsigned int *ptr = base;
for(j=width; j; --j)
*(ptr++) = 0;
- base += (dispDeviceRowBytes >> 3);
+ base += (dispDeviceRowBytes >> 2);
+ }
+}
+
+void btext_flushscreen(void)
+{
+ unsigned int *base = (unsigned int *)calc_base(0, 0);
+ unsigned long width = ((dispDeviceRect[2] - dispDeviceRect[0]) *
+ (dispDeviceDepth >> 3)) >> 2;
+ int i,j;
+
+ for (i=0; i < (dispDeviceRect[3] - dispDeviceRect[1]); i++)
+ {
+ unsigned int *ptr = base;
+ for(j = width; j > 0; j -= 8) {
+ __asm__ __volatile__ ("dcbst 0,%0" :: "r" (ptr));
+ ptr += 8;
+ }
+ base += (dispDeviceRowBytes >> 2);
}
+ __asm__ __volatile__ ("sync" ::: "memory");
}
+void btext_flushline(void)
+{
+ unsigned int *base = (unsigned int *)calc_base(0, g_loc_Y << 4);
+ unsigned long width = ((dispDeviceRect[2] - dispDeviceRect[0]) *
+ (dispDeviceDepth >> 3)) >> 2;
+ int i,j;
+
+ for (i=0; i < 16; i++)
+ {
+ unsigned int *ptr = base;
+ for(j = width; j > 0; j -= 8) {
+ __asm__ __volatile__ ("dcbst 0,%0" :: "r" (ptr));
+ ptr += 8;
+ }
+ base += (dispDeviceRowBytes >> 2);
+ }
+ __asm__ __volatile__ ("sync" ::: "memory");
+}
+
+
#ifndef NO_SCROLL
static void scrollscreen(void)
{
- unsigned long *src = (unsigned long *)calc_base(0,16);
- unsigned long *dst = (unsigned long *)calc_base(0,0);
+ unsigned int *src = (unsigned int *)calc_base(0,16);
+ unsigned int *dst = (unsigned int *)calc_base(0,0);
unsigned long width = ((dispDeviceRect[2] - dispDeviceRect[0]) *
- (dispDeviceDepth >> 3)) >> 3;
+ (dispDeviceDepth >> 3)) >> 2;
int i,j;
for (i=0; i<(dispDeviceRect[3] - dispDeviceRect[1] - 16); i++)
{
- unsigned long *src_ptr = src;
- unsigned long *dst_ptr = dst;
+ unsigned int *src_ptr = src;
+ unsigned int *dst_ptr = dst;
for(j=width; j; --j)
*(dst_ptr++) = *(src_ptr++);
- src += (dispDeviceRowBytes >> 3);
- dst += (dispDeviceRowBytes >> 3);
+ src += (dispDeviceRowBytes >> 2);
+ dst += (dispDeviceRowBytes >> 2);
}
for (i=0; i<16; i++)
{
- unsigned long *dst_ptr = dst;
+ unsigned int *dst_ptr = dst;
for(j=width; j; --j)
*(dst_ptr++) = 0;
- dst += (dispDeviceRowBytes >> 3);
+ dst += (dispDeviceRowBytes >> 2);
}
}
#endif /* ndef NO_SCROLL */
@@ -377,6 +425,14 @@ void btext_drawstring(const char *c)
btext_drawchar(*c++);
}
+void btext_drawtext(const char *c, unsigned int len)
+{
+ if (!boot_text_mapped)
+ return;
+ while (len--)
+ btext_drawchar(*c++);
+}
+
void btext_drawhex(unsigned long v)
{
char *hex_table = "0123456789abcdef";
Index: linux-serialfix/arch/powerpc/kernel/setup_32.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/setup_32.c 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/setup_32.c 2005-11-23 16:54:25.000000000 +1100
@@ -40,6 +40,7 @@
#include <asm/xmon.h>
#include <asm/time.h>
#include <asm/serial.h>
+#include <asm/udbg.h>
#include "setup.h"
@@ -173,12 +174,23 @@ void __init platform_init(void)
*/
void __init machine_init(unsigned long dt_ptr, unsigned long phys)
{
+ /* If btext is enabled, we might have a BAT setup for early display,
+ * thus we do enable some very basic udbg output
+ */
+#ifdef CONFIG_BOOTX_TEXT
+ udbg_putc = btext_drawchar;
+#endif
+
+ /* Do some early initialization based on the flat device tree */
early_init_devtree(__va(dt_ptr));
+ /* Check default command line */
#ifdef CONFIG_CMDLINE
- strlcpy(cmd_line, CONFIG_CMDLINE, sizeof(cmd_line));
+ if (cmd_line[0] == 0)
+ strlcpy(cmd_line, CONFIG_CMDLINE, sizeof(cmd_line));
#endif /* CONFIG_CMDLINE */
+ /* Base init based on machine type */
platform_init();
#ifdef CONFIG_6xx
@@ -294,21 +306,11 @@ void __init setup_arch(char **cmdline_p)
smp_setup_cpu_maps();
-#ifdef CONFIG_BOOTX_TEXT
- init_boot_display();
-#endif
-
-#ifdef CONFIG_PPC_PMAC
- /* This could be called "early setup arch", it must be done
- * now because xmon need it
- */
- if (_machine == _MACH_Pmac)
- pmac_feature_init(); /* New cool way */
-#endif
-
#ifdef CONFIG_XMON_DEFAULT
xmon_init(1);
#endif
+ /* Register early console */
+ register_early_udbg_console();
#if defined(CONFIG_KGDB)
if (ppc_md.kgdb_map_scc)
Index: linux-serialfix/arch/powerpc/kernel/udbg_16550.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/udbg_16550.c 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/udbg_16550.c 2005-11-23 16:54:25.000000000 +1100
@@ -47,7 +47,7 @@ struct NS16550 {
static volatile struct NS16550 __iomem *udbg_comport;
-static void udbg_550_putc(unsigned char c)
+static void udbg_550_putc(char c)
{
if (udbg_comport) {
while ((in_8(&udbg_comport->lsr) & LSR_THRE) == 0)
@@ -69,7 +69,7 @@ static int udbg_550_getc_poll(void)
return -1;
}
-static unsigned char udbg_550_getc(void)
+static char udbg_550_getc(void)
{
if (udbg_comport) {
while ((in_8(&udbg_comport->lsr) & LSR_DR) == 0)
Index: linux-serialfix/arch/powerpc/platforms/powermac/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/Makefile 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/Makefile 2005-11-23 16:54:25.000000000 +1100
@@ -7,3 +7,4 @@ obj-$(CONFIG_NVRAM) += nvram.o
# ppc64 pmac doesn't define CONFIG_NVRAM but needs nvram stuff
obj-$(CONFIG_PPC64) += nvram.o
obj-$(CONFIG_SMP) += smp.o
+obj-$(CONFIG_PPC_MERGE) += udbg_scc.o udbg_adb.o
Index: linux-serialfix/arch/powerpc/platforms/powermac/setup.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/setup.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/setup.c 2005-11-23 16:54:25.000000000 +1100
@@ -76,6 +76,7 @@
#include <asm/pmc.h>
#include <asm/mpic.h>
#include <asm/lmb.h>
+#include <asm/udbg.h>
#include "pmac.h"
@@ -321,16 +322,6 @@ void __init pmac_setup_arch(void)
l2cr_init();
#endif /* CONFIG_PPC32 */
-#ifdef CONFIG_PPC64
- /* Probe motherboard chipset */
- /* this is done earlier in setup_arch for 32-bit */
- pmac_feature_init();
-
- /* We can NAP */
- powersave_nap = 1;
- printk(KERN_INFO "Using native/NAP idle loop\n");
-#endif
-
#ifdef CONFIG_KGDB
zs_kgdb_hook(0);
#endif
@@ -621,13 +612,26 @@ static void __init pmac_init_early(void)
* and call ioremap
*/
hpte_init_native();
+#endif
- /* Init SCC */
- if (strstr(cmd_line, "sccdbg")) {
- sccdbg = 1;
- udbg_init_scc(NULL);
+ /* Enable early btext debug if requested */
+ if (strstr(cmd_line, "btextdbg")) {
+ udbg_adb_init_early();
+ register_early_udbg_console();
}
+ /* Probe motherboard chipset */
+ pmac_feature_init();
+
+ /* We can NAP */
+ powersave_nap = 1;
+ printk(KERN_INFO "Using native/NAP idle loop\n");
+
+ /* Initialize debug stuff */
+ udbg_scc_init(!!strstr(cmd_line, "sccdbg"));
+ udbg_adb_init(!!strstr(cmd_line, "btextdbg"));
+
+#ifdef CONFIG_PPC64
/* Setup interrupt mapping options */
ppc64_interrupt_controller = IC_OPEN_PIC;
@@ -637,19 +641,8 @@ static void __init pmac_init_early(void)
static void __init pmac_progress(char *s, unsigned short hex)
{
-#ifdef CONFIG_PPC64
- if (sccdbg) {
- udbg_puts(s);
- udbg_puts("\n");
- return;
- }
-#endif
-#ifdef CONFIG_BOOTX_TEXT
- if (boot_text_mapped) {
- btext_drawstring(s);
- btext_drawchar('\n');
- }
-#endif /* CONFIG_BOOTX_TEXT */
+ udbg_puts(s);
+ udbg_puts("\n");
}
/*
@@ -734,7 +727,8 @@ static int __init pmac_probe(int platfor
}
#ifdef CONFIG_PPC64
-static int pmac_probe_mode(struct pci_bus *bus)
+/* Move that to pci.c */
+static int pmac_pci_probe_mode(struct pci_bus *bus)
{
struct device_node *node = bus->sysdata;
@@ -770,7 +764,7 @@ struct machdep_calls __initdata pmac_md
.check_legacy_ioport = pmac_check_legacy_ioport,
.progress = pmac_progress,
#ifdef CONFIG_PPC64
- .pci_probe_mode = pmac_probe_mode,
+ .pci_probe_mode = pmac_pci_probe_mode,
.idle_loop = native_idle,
.enable_pmcs = power4_enable_pmcs,
#endif
Index: linux-serialfix/arch/powerpc/xmon/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/xmon/Makefile 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/xmon/Makefile 2005-11-23 16:54:25.000000000 +1100
@@ -3,9 +3,5 @@
ifdef CONFIG_PPC64
EXTRA_CFLAGS += -mno-minimal-toc
endif
-
-obj-$(CONFIG_8xx) += start_8xx.o
-obj-$(CONFIG_6xx) += start_32.o
-obj-$(CONFIG_4xx) += start_32.o
-obj-$(CONFIG_PPC64) += start_64.o
-obj-y += xmon.o ppc-dis.o ppc-opc.o setjmp.o nonstdio.o
+obj-y += xmon.o ppc-dis.o ppc-opc.o setjmp.o start.o \
+ nonstdio.o
Index: linux-serialfix/arch/powerpc/xmon/start.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/xmon/start.c 2005-11-23 16:54:25.000000000 +1100
@@ -0,0 +1,34 @@
+/*
+ * Copyright (C) 1996 Paul Mackerras.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <asm/machdep.h>
+#include <asm/udbg.h>
+#include "nonstdio.h"
+
+void xmon_map_scc(void)
+{
+}
+
+int xmon_write(void *ptr, int nb)
+{
+ return udbg_write(ptr, nb);
+}
+
+int xmon_readchar(void)
+{
+ if (udbg_getc)
+ return udbg_getc();
+ return -1;
+}
+
+int xmon_read_poll(void)
+{
+ if (udbg_getc_poll)
+ return udbg_getc_poll();
+ return -1;
+}
Index: linux-serialfix/arch/powerpc/xmon/start_32.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/xmon/start_32.c 2005-11-23 16:54:13.000000000 +1100
+++ /dev/null 1970-01-01 00:00:00.000000000 +0000
@@ -1,441 +0,0 @@
-/*
- * Copyright (C) 1996 Paul Mackerras.
- */
-#include <linux/config.h>
-#include <linux/string.h>
-#include <asm/machdep.h>
-#include <asm/io.h>
-#include <asm/page.h>
-#include <linux/adb.h>
-#include <linux/pmu.h>
-#include <linux/cuda.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/bitops.h>
-#include <asm/xmon.h>
-#include <asm/prom.h>
-#include <asm/bootx.h>
-#include <asm/machdep.h>
-#include <asm/errno.h>
-#include <asm/pmac_feature.h>
-#include <asm/processor.h>
-#include <asm/delay.h>
-#include <asm/btext.h>
-#include <asm/time.h>
-#include "nonstdio.h"
-
-static volatile unsigned char __iomem *sccc, *sccd;
-unsigned int TXRDY, RXRDY, DLAB;
-
-static int use_serial;
-static int use_screen;
-static int via_modem;
-static int xmon_use_sccb;
-static struct device_node *channel_node;
-
-void buf_access(void)
-{
- if (DLAB)
- sccd[3] &= ~DLAB; /* reset DLAB */
-}
-
-extern int adb_init(void);
-
-#ifdef CONFIG_PPC_CHRP
-/*
- * This looks in the "ranges" property for the primary PCI host bridge
- * to find the physical address of the start of PCI/ISA I/O space.
- * It is basically a cut-down version of pci_process_bridge_OF_ranges.
- */
-static unsigned long chrp_find_phys_io_base(void)
-{
- struct device_node *node;
- unsigned int *ranges;
- unsigned long base = CHRP_ISA_IO_BASE;
- int rlen = 0;
- int np;
-
- node = find_devices("isa");
- if (node != NULL) {
- node = node->parent;
- if (node == NULL || node->type == NULL
- || strcmp(node->type, "pci") != 0)
- node = NULL;
- }
- if (node == NULL)
- node = find_devices("pci");
- if (node == NULL)
- return base;
-
- ranges = (unsigned int *) get_property(node, "ranges", &rlen);
- np = prom_n_addr_cells(node) + 5;
- while ((rlen -= np * sizeof(unsigned int)) >= 0) {
- if ((ranges[0] >> 24) == 1 && ranges[2] == 0) {
- /* I/O space starting at 0, grab the phys base */
- base = ranges[np - 3];
- break;
- }
- ranges += np;
- }
- return base;
-}
-#endif /* CONFIG_PPC_CHRP */
-
-void xmon_map_scc(void)
-{
-#ifdef CONFIG_PPC_MULTIPLATFORM
- volatile unsigned char __iomem *base;
-
- if (_machine == _MACH_Pmac) {
- struct device_node *np;
- unsigned long addr;
-#ifdef CONFIG_BOOTX_TEXT
- if (!use_screen && !use_serial
- && !machine_is_compatible("iMac")) {
- /* see if there is a keyboard in the device tree
- with a parent of type "adb" */
- for (np = find_devices("keyboard"); np; np = np->next)
- if (np->parent && np->parent->type
- && strcmp(np->parent->type, "adb") == 0)
- break;
-
- /* needs to be hacked if xmon_printk is to be used
- from within find_via_pmu() */
-#ifdef CONFIG_ADB_PMU
- if (np != NULL && boot_text_mapped && find_via_pmu())
- use_screen = 1;
-#endif
-#ifdef CONFIG_ADB_CUDA
- if (np != NULL && boot_text_mapped && find_via_cuda())
- use_screen = 1;
-#endif
- }
- if (!use_screen && (np = find_devices("escc")) != NULL) {
- /*
- * look for the device node for the serial port
- * we're using and see if it says it has a modem
- */
- char *name = xmon_use_sccb? "ch-b": "ch-a";
- char *slots;
- int l;
-
- np = np->child;
- while (np != NULL && strcmp(np->name, name) != 0)
- np = np->sibling;
- if (np != NULL) {
- /* XXX should parse this properly */
- channel_node = np;
- slots = get_property(np, "slot-names", &l);
- if (slots != NULL && l >= 10
- && strcmp(slots+4, "Modem") == 0)
- via_modem = 1;
- }
- }
- btext_drawstring("xmon uses ");
- if (use_screen)
- btext_drawstring("screen and keyboard\n");
- else {
- if (via_modem)
- btext_drawstring("modem on ");
- btext_drawstring(xmon_use_sccb? "printer": "modem");
- btext_drawstring(" port\n");
- }
-
-#endif /* CONFIG_BOOTX_TEXT */
-
-#ifdef CHRP_ESCC
- addr = 0xc1013020;
-#else
- addr = 0xf3013020;
-#endif
- TXRDY = 4;
- RXRDY = 1;
-
- np = find_devices("mac-io");
- if (np && np->n_addrs)
- addr = np->addrs[0].address + 0x13020;
- base = (volatile unsigned char *) ioremap(addr & PAGE_MASK, PAGE_SIZE);
- sccc = base + (addr & ~PAGE_MASK);
- sccd = sccc + 0x10;
-
- } else {
- base = (volatile unsigned char *) isa_io_base;
-
-#ifdef CONFIG_PPC_CHRP
- if (_machine == _MACH_chrp)
- base = (volatile unsigned char __iomem *)
- ioremap(chrp_find_phys_io_base(), 0x1000);
-#endif
-
- sccc = base + 0x3fd;
- sccd = base + 0x3f8;
- if (xmon_use_sccb) {
- sccc -= 0x100;
- sccd -= 0x100;
- }
- TXRDY = 0x20;
- RXRDY = 1;
- DLAB = 0x80;
- }
-#elif defined(CONFIG_GEMINI)
- /* should already be mapped by the kernel boot */
- sccc = (volatile unsigned char __iomem *) 0xffeffb0d;
- sccd = (volatile unsigned char __iomem *) 0xffeffb08;
- TXRDY = 0x20;
- RXRDY = 1;
- DLAB = 0x80;
-#elif defined(CONFIG_405GP)
- sccc = (volatile unsigned char __iomem *)0xef600305;
- sccd = (volatile unsigned char __iomem *)0xef600300;
- TXRDY = 0x20;
- RXRDY = 1;
- DLAB = 0x80;
-#endif /* platform */
-}
-
-static int scc_initialized = 0;
-
-void xmon_init_scc(void);
-extern void cuda_poll(void);
-
-static inline void do_poll_adb(void)
-{
-#ifdef CONFIG_ADB_PMU
- if (sys_ctrler == SYS_CTRLER_PMU)
- pmu_poll_adb();
-#endif /* CONFIG_ADB_PMU */
-#ifdef CONFIG_ADB_CUDA
- if (sys_ctrler == SYS_CTRLER_CUDA)
- cuda_poll();
-#endif /* CONFIG_ADB_CUDA */
-}
-
-int xmon_write(void *ptr, int nb)
-{
- char *p = ptr;
- int i, c, ct;
-
-#ifdef CONFIG_SMP
- static unsigned long xmon_write_lock;
- int lock_wait = 1000000;
- int locked;
-
- while ((locked = test_and_set_bit(0, &xmon_write_lock)) != 0)
- if (--lock_wait == 0)
- break;
-#endif
-
-#ifdef CONFIG_BOOTX_TEXT
- if (use_screen) {
- /* write it on the screen */
- for (i = 0; i < nb; ++i)
- btext_drawchar(*p++);
- goto out;
- }
-#endif
- if (!scc_initialized)
- xmon_init_scc();
- ct = 0;
- for (i = 0; i < nb; ++i) {
- while ((*sccc & TXRDY) == 0)
- do_poll_adb();
- c = p[i];
- if (c == '\n' && !ct) {
- c = '\r';
- ct = 1;
- --i;
- } else {
- ct = 0;
- }
- buf_access();
- *sccd = c;
- eieio();
- }
-
- out:
-#ifdef CONFIG_SMP
- if (!locked)
- clear_bit(0, &xmon_write_lock);
-#endif
- return nb;
-}
-
-int xmon_wants_key;
-int xmon_adb_keycode;
-
-#ifdef CONFIG_BOOTX_TEXT
-static int xmon_adb_shiftstate;
-
-static unsigned char xmon_keytab[128] =
- "asdfhgzxcv\000bqwer" /* 0x00 - 0x0f */
- "yt123465=97-80]o" /* 0x10 - 0x1f */
- "u[ip\rlj'k;\\,/nm." /* 0x20 - 0x2f */
- "\t `\177\0\033\0\0\0\0\0\0\0\0\0\0" /* 0x30 - 0x3f */
- "\0.\0*\0+\0\0\0\0\0/\r\0-\0" /* 0x40 - 0x4f */
- "\0\0000123456789\0\0\0"; /* 0x50 - 0x5f */
-
-static unsigned char xmon_shift_keytab[128] =
- "ASDFHGZXCV\000BQWER" /* 0x00 - 0x0f */
- "YT!@#$^%+(&_*)}O" /* 0x10 - 0x1f */
- "U{IP\rLJ\"K:|<?NM>" /* 0x20 - 0x2f */
- "\t ~\177\0\033\0\0\0\0\0\0\0\0\0\0" /* 0x30 - 0x3f */
- "\0.\0*\0+\0\0\0\0\0/\r\0-\0" /* 0x40 - 0x4f */
- "\0\0000123456789\0\0\0"; /* 0x50 - 0x5f */
-
-static int xmon_get_adb_key(void)
-{
- int k, t, on;
-
- xmon_wants_key = 1;
- for (;;) {
- xmon_adb_keycode = -1;
- t = 0;
- on = 0;
- do {
- if (--t < 0) {
- on = 1 - on;
- btext_drawchar(on? 0xdb: 0x20);
- btext_drawchar('\b');
- t = 200000;
- }
- do_poll_adb();
- } while (xmon_adb_keycode == -1);
- k = xmon_adb_keycode;
- if (on)
- btext_drawstring(" \b");
-
- /* test for shift keys */
- if ((k & 0x7f) == 0x38 || (k & 0x7f) == 0x7b) {
- xmon_adb_shiftstate = (k & 0x80) == 0;
- continue;
- }
- if (k >= 0x80)
- continue; /* ignore up transitions */
- k = (xmon_adb_shiftstate? xmon_shift_keytab: xmon_keytab)[k];
- if (k != 0)
- break;
- }
- xmon_wants_key = 0;
- return k;
-}
-#endif /* CONFIG_BOOTX_TEXT */
-
-int xmon_readchar(void)
-{
-#ifdef CONFIG_BOOTX_TEXT
- if (use_screen)
- return xmon_get_adb_key();
-#endif
- if (!scc_initialized)
- xmon_init_scc();
- while ((*sccc & RXRDY) == 0)
- do_poll_adb();
- buf_access();
- return *sccd;
-}
-
-int xmon_read_poll(void)
-{
- if ((*sccc & RXRDY) == 0) {
- do_poll_adb();
- return -1;
- }
- buf_access();
- return *sccd;
-}
-
-static unsigned char scc_inittab[] = {
- 13, 0, /* set baud rate divisor */
- 12, 1,
- 14, 1, /* baud rate gen enable, src=rtxc */
- 11, 0x50, /* clocks = br gen */
- 5, 0xea, /* tx 8 bits, assert DTR & RTS */
- 4, 0x46, /* x16 clock, 1 stop */
- 3, 0xc1, /* rx enable, 8 bits */
-};
-
-void xmon_init_scc(void)
-{
- if ( _machine == _MACH_chrp )
- {
- sccd[3] = 0x83; eieio(); /* LCR = 8N1 + DLAB */
- sccd[0] = 12; eieio(); /* DLL = 9600 baud */
- sccd[1] = 0; eieio();
- sccd[2] = 0; eieio(); /* FCR = 0 */
- sccd[3] = 3; eieio(); /* LCR = 8N1 */
- sccd[1] = 0; eieio(); /* IER = 0 */
- }
- else if ( _machine == _MACH_Pmac )
- {
- int i, x;
- unsigned long timeout;
-
- if (channel_node != 0)
- pmac_call_feature(
- PMAC_FTR_SCC_ENABLE,
- channel_node,
- PMAC_SCC_ASYNC | PMAC_SCC_FLAG_XMON, 1);
- printk(KERN_INFO "Serial port locked ON by debugger !\n");
- if (via_modem && channel_node != 0) {
- unsigned int t0;
-
- pmac_call_feature(
- PMAC_FTR_MODEM_ENABLE,
- channel_node, 0, 1);
- printk(KERN_INFO "Modem powered up by debugger !\n");
- t0 = get_tbl();
- timeout = 3 * tb_ticks_per_sec;
- if (timeout == 0)
- /* assume 25MHz if tb_ticks_per_sec not set */
- timeout = 75000000;
- while (get_tbl() - t0 < timeout)
- eieio();
- }
- /* use the B channel if requested */
- if (xmon_use_sccb) {
- sccc = (volatile unsigned char *)
- ((unsigned long)sccc & ~0x20);
- sccd = sccc + 0x10;
- }
- for (i = 20000; i != 0; --i) {
- x = *sccc; eieio();
- }
- *sccc = 9; eieio(); /* reset A or B side */
- *sccc = ((unsigned long)sccc & 0x20)? 0x80: 0x40; eieio();
- for (i = 0; i < sizeof(scc_inittab); ++i) {
- *sccc = scc_inittab[i];
- eieio();
- }
- }
- scc_initialized = 1;
- if (via_modem) {
- for (;;) {
- xmon_write("ATE1V1\r", 7);
- if (xmon_expect("OK", 5)) {
- xmon_write("ATA\r", 4);
- if (xmon_expect("CONNECT", 40))
- break;
- }
- xmon_write("+++", 3);
- xmon_expect("OK", 3);
- }
- }
-}
-
-void xmon_enter(void)
-{
-#ifdef CONFIG_ADB_PMU
- if (_machine == _MACH_Pmac) {
- pmu_suspend();
- }
-#endif
-}
-
-void xmon_leave(void)
-{
-#ifdef CONFIG_ADB_PMU
- if (_machine == _MACH_Pmac) {
- pmu_resume();
- }
-#endif
-}
Index: linux-serialfix/arch/powerpc/xmon/start_64.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/xmon/start_64.c 2005-11-23 16:54:13.000000000 +1100
+++ /dev/null 1970-01-01 00:00:00.000000000 +0000
@@ -1,34 +0,0 @@
-/*
- * Copyright (C) 1996 Paul Mackerras.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#include <asm/machdep.h>
-#include <asm/udbg.h>
-#include "nonstdio.h"
-
-void xmon_map_scc(void)
-{
-}
-
-int xmon_write(void *ptr, int nb)
-{
- return udbg_write(ptr, nb);
-}
-
-int xmon_readchar(void)
-{
- if (udbg_getc)
- return udbg_getc();
- return -1;
-}
-
-int xmon_read_poll(void)
-{
- if (udbg_getc_poll)
- return udbg_getc_poll();
- return -1;
-}
Index: linux-serialfix/arch/powerpc/xmon/start_8xx.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/xmon/start_8xx.c 2005-11-23 16:54:13.000000000 +1100
+++ /dev/null 1970-01-01 00:00:00.000000000 +0000
@@ -1,44 +0,0 @@
-/*
- * Copyright (C) 1996 Paul Mackerras.
- * Copyright (C) 2000 Dan Malek.
- * Quick hack of Paul's code to make XMON work on 8xx processors. Lots
- * of assumptions, like the SMC1 is used, it has been initialized by the
- * loader at some point, and we can just stuff and suck bytes.
- * We rely upon the 8xx uart driver to support us, as the interface
- * changes between boot up and operational phases of the kernel.
- */
-#include <linux/string.h>
-#include <asm/machdep.h>
-#include <asm/io.h>
-#include <asm/page.h>
-#include <linux/kernel.h>
-#include <asm/8xx_immap.h>
-#include <asm/mpc8xx.h>
-#include <asm/commproc.h>
-#include "nonstdio.h"
-
-extern int xmon_8xx_write(char *str, int nb);
-extern int xmon_8xx_read_poll(void);
-extern int xmon_8xx_read_char(void);
-
-void xmon_map_scc(void)
-{
- cpmp = (cpm8xx_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
-}
-
-void xmon_init_scc(void);
-
-int xmon_write(void *ptr, int nb)
-{
- return(xmon_8xx_write(ptr, nb));
-}
-
-int xmon_readchar(void)
-{
- return xmon_8xx_read_char();
-}
-
-int xmon_read_poll(void)
-{
- return(xmon_8xx_read_poll());
-}
Index: linux-serialfix/include/asm-powerpc/btext.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/btext.h 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/btext.h 2005-11-23 16:54:25.000000000 +1100
@@ -7,21 +7,22 @@
#define __PPC_BTEXT_H
#ifdef __KERNEL__
-extern void btext_clearscreen(void);
-extern void btext_flushscreen(void);
-
-extern int boot_text_mapped;
-
-extern int btext_initialize(struct device_node *np);
-
-extern void map_boot_text(void);
-extern void init_boot_display(void);
+extern int btext_find_display(int allow_nonstdout);
extern void btext_update_display(unsigned long phys, int width, int height,
int depth, int pitch);
+extern void btext_setup_display(int width, int height, int depth, int pitch,
+ unsigned long address);
+extern void btext_prepare_BAT(void);
+extern void btext_unmap(void);
extern void btext_drawchar(char c);
extern void btext_drawstring(const char *str);
extern void btext_drawhex(unsigned long v);
+extern void btext_drawtext(const char *c, unsigned int len);
+
+extern void btext_clearscreen(void);
+extern void btext_flushscreen(void);
+extern void btext_flushline(void);
#endif /* __KERNEL__ */
#endif /* __PPC_BTEXT_H */
Index: linux-serialfix/include/asm-powerpc/udbg.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/udbg.h 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/udbg.h 2005-11-23 16:54:25.000000000 +1100
@@ -13,8 +13,8 @@
#include <linux/compiler.h>
#include <linux/init.h>
-extern void (*udbg_putc)(unsigned char c);
-extern unsigned char (*udbg_getc)(void);
+extern void (*udbg_putc)(char c);
+extern char (*udbg_getc)(void);
extern int (*udbg_getc_poll)(void);
extern void udbg_puts(const char *s);
@@ -30,5 +30,8 @@ extern unsigned int udbg_probe_uart_spee
unsigned int clock);
struct device_node;
-extern void udbg_init_scc(struct device_node *np);
+extern void udbg_scc_init(int force_scc);
+extern int udbg_adb_init(int force_btext);
+extern void udbg_adb_init_early(void);
+
#endif /* _ASM_POWERPC_UDBG_H */
Index: linux-serialfix/arch/powerpc/kernel/setup_64.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/setup_64.c 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/setup_64.c 2005-11-23 16:54:25.000000000 +1100
@@ -466,10 +466,6 @@ void __init setup_system(void)
*/
finish_device_tree();
-#ifdef CONFIG_BOOTX_TEXT
- init_boot_display();
-#endif
-
/*
* Initialize xmon
*/
Index: linux-serialfix/arch/powerpc/platforms/powermac/feature.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/feature.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/feature.c 2005-11-23 16:54:25.000000000 +1100
@@ -2596,6 +2596,8 @@ found:
*/
static void __init probe_uninorth(void)
{
+ u32 *addrp;
+ phys_addr_t address;
unsigned long actrl;
/* Locate core99 Uni-N */
@@ -2605,20 +2607,23 @@ static void __init probe_uninorth(void)
uninorth_node = of_find_node_by_name(NULL, "u3");
uninorth_u3 = 1;
}
- if (uninorth_node && uninorth_node->n_addrs > 0) {
- unsigned long address = uninorth_node->addrs[0].address;
- uninorth_base = ioremap(address, 0x40000);
- uninorth_rev = in_be32(UN_REG(UNI_N_VERSION));
- if (uninorth_u3)
- u3_ht = ioremap(address + U3_HT_CONFIG_BASE, 0x1000);
- } else
- uninorth_node = NULL;
+ if (uninorth_node == NULL)
+ return;
- if (!uninorth_node)
+ addrp = (u32 *)get_property(uninorth_node, "reg", NULL);
+ if (addrp == NULL)
+ return;
+ address = of_translate_address(uninorth_node, addrp);
+ if (address == 0)
return;
+ uninorth_base = ioremap(address, 0x40000);
+ uninorth_rev = in_be32(UN_REG(UNI_N_VERSION));
+ if (uninorth_u3)
+ u3_ht = ioremap(address + U3_HT_CONFIG_BASE, 0x1000);
- printk(KERN_INFO "Found %s memory controller & host bridge, revision: %d\n",
- uninorth_u3 ? "U3" : "UniNorth", uninorth_rev);
+ printk(KERN_INFO "Found %s memory controller & host bridge,"
+ " revision: %d\n", uninorth_u3 ? "U3" : "UniNorth",
+ uninorth_rev);
printk(KERN_INFO "Mapped at 0x%08lx\n", (unsigned long)uninorth_base);
/* Set the arbitrer QAck delay according to what Apple does
@@ -2642,18 +2647,17 @@ static void __init probe_one_macio(const
{
struct device_node* node;
int i;
- volatile u32 __iomem * base;
- u32* revp;
+ volatile u32 __iomem *base;
+ u32 *addrp, *revp;
+ phys_addr_t addr;
+ u64 size;
- node = find_devices(name);
- if (!node || !node->n_addrs)
- return;
- if (compat)
- do {
- if (device_is_compatible(node, compat))
- break;
- node = node->next;
- } while (node);
+ for (node = NULL; (node = of_find_node_by_name(node, name)) != NULL;) {
+ if (!compat)
+ break;
+ if (device_is_compatible(node, compat))
+ break;
+ }
if (!node)
return;
for(i=0; i<MAX_MACIO_CHIPS; i++) {
@@ -2662,14 +2666,28 @@ static void __init probe_one_macio(const
if (macio_chips[i].of_node == node)
return;
}
+
if (i >= MAX_MACIO_CHIPS) {
printk(KERN_ERR "pmac_feature: Please increase MAX_MACIO_CHIPS !\n");
printk(KERN_ERR "pmac_feature: %s skipped\n", node->full_name);
return;
}
- base = ioremap(node->addrs[0].address, node->addrs[0].size);
+ addrp = of_get_pci_address(node, 0, &size);
+ if (addrp == NULL) {
+ printk(KERN_ERR "pmac_feature: %s: can't find base !\n",
+ node->full_name);
+ return;
+ }
+ addr = of_translate_address(node, addrp);
+ if (addr == 0) {
+ printk(KERN_ERR "pmac_feature: %s, can't translate base !\n",
+ node->full_name);
+ return;
+ }
+ base = ioremap(addr, (unsigned long)size);
if (!base) {
- printk(KERN_ERR "pmac_feature: Can't map mac-io chip !\n");
+ printk(KERN_ERR "pmac_feature: %s, can't map mac-io chip !\n",
+ node->full_name);
return;
}
if (type == macio_keylargo) {
Index: linux-serialfix/arch/powerpc/platforms/powermac/low_i2c.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/low_i2c.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/low_i2c.c 2005-11-23 16:54:25.000000000 +1100
@@ -36,7 +36,7 @@
#ifdef DEBUG
#define DBG(x...) do {\
- printk(KERN_DEBUG "KW:" x); \
+ printk(KERN_DEBUG "low_i2c:" x); \
} while(0)
#else
#define DBG(x...)
@@ -342,7 +342,7 @@ static int keywest_low_i2c_func(struct l
static void keywest_low_i2c_add(struct device_node *np)
{
struct low_i2c_host *host = find_low_i2c_host(NULL);
- u32 *psteps, *prate, steps, aoffset = 0;
+ u32 *psteps, *prate, *addrp, steps;
struct device_node *parent;
if (host == NULL) {
@@ -352,6 +352,16 @@ static void keywest_low_i2c_add(struct d
}
memset(host, 0, sizeof(*host));
+ /* Apple is kind enough to provide a valid AAPL,address property
+ * on all i2c keywest nodes so far ... we would have to fallback
+ * to macio parsing if that wasn't the case
+ */
+ addrp = (u32 *)get_property(np, "AAPL,address", NULL);
+ if (addrp == NULL) {
+ printk(KERN_ERR "low_i2c: Can't find address for %s\n",
+ np->full_name);
+ return;
+ }
init_MUTEX(&host->mutex);
host->np = of_node_get(np);
psteps = (u32 *)get_property(np, "AAPL,address-step", NULL);
@@ -360,12 +370,10 @@ static void keywest_low_i2c_add(struct d
steps >>= 1;
parent = of_get_parent(np);
host->num_channels = 1;
- if (parent && parent->name[0] == 'u') {
+ if (parent && parent->name[0] == 'u')
host->num_channels = 2;
- aoffset = 3;
- }
/* Select interface rate */
- host->speed = KW_I2C_MODE_100KHZ;
+ host->speed = KW_I2C_MODE_25KHZ;
prate = (u32 *)get_property(np, "AAPL,i2c-rate", NULL);
if (prate) switch(*prate) {
case 100:
@@ -379,9 +387,12 @@ static void keywest_low_i2c_add(struct d
break;
}
+ printk(KERN_INFO "low_i2c: Bus %s found at 0x%08x, %d channels,"
+ " speed = %d KHz\n",
+ np->full_name, *addrp, host->num_channels, prate ? *prate : 25);
+
host->mode = pmac_low_i2c_mode_std;
- host->base = ioremap(np->addrs[0].address + aoffset,
- np->addrs[0].size);
+ host->base = ioremap((*addrp), 0x1000);
host->func = keywest_low_i2c_func;
}
Index: linux-serialfix/arch/powerpc/platforms/powermac/pic.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/powermac/pic.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/powermac/pic.c 2005-11-23 16:54:25.000000000 +1100
@@ -459,7 +459,7 @@ void __init pmac_pic_init(void)
mpic_setup_cascade(irqctrler2->intrs[0].line,
pmac_u3_cascade, mpic2);
}
-#if defined(CONFIG_XMON) && defined(CONFIG_PPC32)
+#ifdef CONFIG_XMON
{
struct device_node* pswitch;
int nmi_irq;
Index: linux-serialfix/arch/powerpc/platforms/pseries/lpar.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/pseries/lpar.c 2005-11-23 16:54:25.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/pseries/lpar.c 2005-11-23 16:54:25.000000000 +1100
@@ -61,7 +61,7 @@ extern void pSeries_find_serial_port(voi
int vtermno; /* virtual terminal# for udbg */
#define __ALIGNED__ __attribute__((__aligned__(sizeof(long))))
-static void udbg_hvsi_putc(unsigned char c)
+static void udbg_hvsi_putc(char c)
{
/* packet's seqno isn't used anyways */
uint8_t packet[] __ALIGNED__ = { 0xff, 5, 0, 0, c };
@@ -112,7 +112,7 @@ static int udbg_hvsi_getc_poll(void)
return ch;
}
-static unsigned char udbg_hvsi_getc(void)
+static char udbg_hvsi_getc(void)
{
int ch;
for (;;) {
@@ -128,7 +128,7 @@ static unsigned char udbg_hvsi_getc(void
}
}
-static void udbg_putcLP(unsigned char c)
+static void udbg_putcLP(char c)
{
char buf[16];
unsigned long rc;
@@ -173,7 +173,7 @@ static int udbg_getc_pollLP(void)
return ch;
}
-static unsigned char udbg_getcLP(void)
+static char udbg_getcLP(void)
{
int ch;
for (;;) {
Index: linux-serialfix/arch/powerpc/kernel/head_32.S
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/head_32.S 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/head_32.S 2005-11-23 16:54:25.000000000 +1100
@@ -153,6 +153,9 @@ __after_mmu_off:
bl flush_tlbs
bl initial_bats
+#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+ bl setup_disp_bat
+#endif
/*
* Call setup_cpu for CPU 0 and initialize 6xx Idle
@@ -1306,6 +1309,32 @@ initial_bats:
blr
+#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
+setup_disp_bat:
+ /*
+ * setup the display bat prepared for us in prom.c
+ */
+ mflr r8
+ bl reloc_offset
+ mtlr r8
+ addis r8,r3,disp_BAT@ha
+ addi r8,r8,disp_BAT@l
+ cmpwi cr0,r8,0
+ beqlr
+ lwz r11,0(r8)
+ lwz r8,4(r8)
+ mfspr r9,SPRN_PVR
+ rlwinm r9,r9,16,16,31 /* r9 = 1 for 601, 4 for 604 */
+ cmpwi 0,r9,1
+ beq 1f
+ mtspr SPRN_DBAT3L,r8
+ mtspr SPRN_DBAT3U,r11
+ blr
+1: mtspr SPRN_IBAT3L,r8
+ mtspr SPRN_IBAT3U,r11
+ blr
+#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */
+
#ifdef CONFIG_8260
/* Jump into the system reset for the rom.
* We first disable the MMU, and then jump to the ROM reset address.
Index: linux-serialfix/arch/powerpc/mm/init_32.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/mm/init_32.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/powerpc/mm/init_32.c 2005-11-23 16:54:25.000000000 +1100
@@ -188,6 +188,11 @@ void __init MMU_init(void)
if (ppc_md.progress)
ppc_md.progress("MMU:exit", 0x211);
+
+ /* From now on, btext is no longer BAT mapped if it was at all */
+#ifdef CONFIG_BOOTX_TEXT
+ btext_unmap();
+#endif
}
/* This is only called until mem_init is done. */
Index: linux-serialfix/drivers/i2c/busses/i2c-keywest.c
===================================================================
--- linux-serialfix.orig/drivers/i2c/busses/i2c-keywest.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/drivers/i2c/busses/i2c-keywest.c 2005-11-23 16:54:25.000000000 +1100
@@ -505,16 +505,23 @@ static int
create_iface(struct device_node *np, struct device *dev)
{
unsigned long steps;
- unsigned bsteps, tsize, i, nchan, addroffset;
+ unsigned bsteps, tsize, i, nchan;
struct keywest_iface* iface;
- u32 *psteps, *prate;
+ u32 *psteps, *prate, *addrp;
int rc;
- if (np->n_intrs < 1 || np->n_addrs < 1) {
- printk(KERN_ERR "%s: Missing interrupt or address !\n",
+ if (np->n_intrs < 1) {
+ printk(KERN_ERR "%s: Missing interrupt !\n",
np->full_name);
return -ENODEV;
}
+ addrp = (u32 *)get_property(np, "AAPL,address", NULL);
+ if (addrp == NULL) {
+ printk(KERN_ERR "%s: Can't find address !\n",
+ np->full_name);
+ return -ENODEV;
+ }
+
if (pmac_low_i2c_lock(np))
return -ENODEV;
@@ -525,13 +532,10 @@ create_iface(struct device_node *np, str
for (bsteps = 0; (steps & 0x01) == 0; bsteps++)
steps >>= 1;
- if (np->parent->name[0] == 'u') {
+ if (np->parent->name[0] == 'u')
nchan = 2;
- addroffset = 3;
- } else {
- addroffset = 0;
+ else
nchan = 1;
- }
tsize = sizeof(struct keywest_iface) +
(sizeof(struct keywest_chan) + 4) * nchan;
@@ -550,8 +554,7 @@ create_iface(struct device_node *np, str
iface->irq = np->intrs[0].line;
iface->channels = (struct keywest_chan *)
(((unsigned long)(iface + 1) + 3UL) & ~3UL);
- iface->base = ioremap(np->addrs[0].address + addroffset,
- np->addrs[0].size);
+ iface->base = ioremap(*addrp, 0x1000);
if (!iface->base) {
printk(KERN_ERR "i2c-keywest: can't map inteface !\n");
kfree(iface);
Index: linux-serialfix/drivers/macintosh/via-cuda.c
===================================================================
--- linux-serialfix.orig/drivers/macintosh/via-cuda.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/drivers/macintosh/via-cuda.c 2005-11-23 16:54:25.000000000 +1100
@@ -127,39 +127,34 @@ struct adb_driver via_cuda_driver = {
#endif /* CONFIG_ADB */
#ifdef CONFIG_PPC
-int __init
-find_via_cuda(void)
+int __init find_via_cuda(void)
{
- int err;
struct adb_request req;
+ phys_addr_t taddr;
+ u32 *reg;
+ int err;
if (vias != 0)
return 1;
- vias = find_devices("via-cuda");
+ vias = of_find_node_by_name(NULL, "via-cuda");
if (vias == 0)
return 0;
- if (vias->next != 0)
- printk(KERN_WARNING "Warning: only using 1st via-cuda\n");
-
-#if 0
- { int i;
-
- printk("find_via_cuda: node = %p, addrs =", vias->node);
- for (i = 0; i < vias->n_addrs; ++i)
- printk(" %x(%x)", vias->addrs[i].address, vias->addrs[i].size);
- printk(", intrs =");
- for (i = 0; i < vias->n_intrs; ++i)
- printk(" %x", vias->intrs[i].line);
- printk("\n"); }
-#endif
- if (vias->n_addrs != 1 || vias->n_intrs != 1) {
- printk(KERN_ERR "via-cuda: expecting 1 address (%d) and 1 interrupt (%d)\n",
- vias->n_addrs, vias->n_intrs);
- if (vias->n_addrs < 1 || vias->n_intrs < 1)
- return 0;
+ reg = (u32 *)get_property(vias, "reg", NULL);
+ if (reg == NULL) {
+ printk(KERN_ERR "via-cuda: No \"reg\" property !\n");
+ goto fail;
+ }
+ taddr = of_translate_address(vias, reg);
+ if (taddr == 0) {
+ printk(KERN_ERR "via-cuda: Can't translate address !\n");
+ goto fail;
+ }
+ via = ioremap(taddr, 0x2000);
+ if (via == NULL) {
+ printk(KERN_ERR "via-cuda: Can't map address !\n");
+ goto fail;
}
- via = ioremap(vias->addrs->address, 0x2000);
cuda_state = idle;
sys_ctrler = SYS_CTRLER_CUDA;
@@ -185,6 +180,11 @@ find_via_cuda(void)
cuda_poll();
return 1;
+
+ fail:
+ of_node_put(vias);
+ vias = NULL;
+ return 0;
}
#endif /* CONFIG_PPC */
Index: linux-serialfix/drivers/macintosh/via-pmu.c
===================================================================
--- linux-serialfix.orig/drivers/macintosh/via-pmu.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/drivers/macintosh/via-pmu.c 2005-11-23 16:54:25.000000000 +1100
@@ -147,6 +147,7 @@ static struct device_node *vias;
static int pmu_kind = PMU_UNKNOWN;
static int pmu_fully_inited = 0;
static int pmu_has_adb;
+static struct device_node *gpio_node;
static unsigned char __iomem *gpio_reg = NULL;
static int gpio_irq = -1;
static int gpio_irq_enabled = -1;
@@ -295,22 +296,26 @@ static struct backlight_controller pmu_b
};
#endif /* CONFIG_PMAC_BACKLIGHT */
-int
-find_via_pmu(void)
+int __init find_via_pmu(void)
{
+ phys_addr_t taddr;
+ u32 *reg;
+
if (via != 0)
return 1;
- vias = find_devices("via-pmu");
- if (vias == 0)
+ vias = of_find_node_by_name(NULL, "via-pmu");
+ if (vias == NULL)
return 0;
- if (vias->next != 0)
- printk(KERN_WARNING "Warning: only using 1st via-pmu\n");
- if (vias->n_addrs < 1 || vias->n_intrs < 1) {
- printk(KERN_ERR "via-pmu: %d addresses, %d interrupts!\n",
- vias->n_addrs, vias->n_intrs);
- if (vias->n_addrs < 1 || vias->n_intrs < 1)
- return 0;
+ reg = (u32 *)get_property(vias, "reg", NULL);
+ if (reg == NULL) {
+ printk(KERN_ERR "via-pmu: No \"reg\" property !\n");
+ goto fail;
+ }
+ taddr = of_translate_address(vias, reg);
+ if (taddr == 0) {
+ printk(KERN_ERR "via-pmu: Can't translate address !\n");
+ goto fail;
}
spin_lock_init(&pmu_lock);
@@ -331,7 +336,8 @@ find_via_pmu(void)
pmu_kind = PMU_HEATHROW_BASED;
else if (device_is_compatible(vias->parent, "Keylargo")
|| device_is_compatible(vias->parent, "K2-Keylargo")) {
- struct device_node *gpio, *gpiop;
+ struct device_node *gpiop;
+ phys_addr_t gaddr = 0;
pmu_kind = PMU_KEYLARGO_BASED;
pmu_has_adb = (find_type_devices("adb") != NULL);
@@ -341,19 +347,24 @@ find_via_pmu(void)
PMU_INT_TICK |
PMU_INT_ENVIRONMENT;
- gpiop = find_devices("gpio");
- if (gpiop && gpiop->n_addrs) {
- gpio_reg = ioremap(gpiop->addrs->address, 0x10);
- gpio = find_devices("extint-gpio1");
- if (gpio == NULL)
- gpio = find_devices("pmu-interrupt");
- if (gpio && gpio->parent == gpiop && gpio->n_intrs)
- gpio_irq = gpio->intrs[0].line;
+ gpiop = of_find_node_by_name(NULL, "gpio");
+ if (gpiop) {
+ reg = (u32 *)get_property(gpiop, "reg", NULL);
+ if (reg)
+ gaddr = of_translate_address(gpiop, reg);
+ if (gaddr != 0)
+ gpio_reg = ioremap(gaddr, 0x10);
}
+ if (gpio_reg == NULL)
+ printk(KERN_ERR "via-pmu: Can't find GPIO reg !\n");
} else
pmu_kind = PMU_UNKNOWN;
- via = ioremap(vias->addrs->address, 0x2000);
+ via = ioremap(taddr, 0x2000);
+ if (via == NULL) {
+ printk(KERN_ERR "via-pmu: Can't map address !\n");
+ goto fail;
+ }
out_8(&via[IER], IER_CLR | 0x7f); /* disable all intrs */
out_8(&via[IFR], 0x7f); /* clear IFR */
@@ -371,17 +382,19 @@ find_via_pmu(void)
sys_ctrler = SYS_CTRLER_PMU;
return 1;
+ fail:
+ of_node_put(vias);
+ vias = NULL;
+ return 0;
}
#ifdef CONFIG_ADB
-static int
-pmu_probe(void)
+static int pmu_probe(void)
{
return vias == NULL? -ENODEV: 0;
}
-static int __init
-pmu_init(void)
+static int __init pmu_init(void)
{
if (vias == NULL)
return -ENODEV;
@@ -405,7 +418,7 @@ static int __init via_pmu_start(void)
bright_req_2.complete = 1;
batt_req.complete = 1;
-#if defined(CONFIG_PPC32) && !defined(CONFIG_PPC_MERGE)
+#ifndef CONFIG_PPC_MERGE
if (pmu_kind == PMU_KEYLARGO_BASED)
openpic_set_irq_priority(vias->intrs[0].line,
OPENPIC_PRIORITY_DEFAULT + 1);
@@ -418,10 +431,22 @@ static int __init via_pmu_start(void)
return -EAGAIN;
}
- if (pmu_kind == PMU_KEYLARGO_BASED && gpio_irq != -1) {
- if (request_irq(gpio_irq, gpio1_interrupt, 0, "GPIO1 ADB", (void *)0))
- printk(KERN_ERR "pmu: can't get irq %d (GPIO1)\n", gpio_irq);
- gpio_irq_enabled = 1;
+ if (pmu_kind == PMU_KEYLARGO_BASED) {
+ gpio_node = of_find_node_by_name(NULL, "extint-gpio1");
+ if (gpio_node == NULL)
+ gpio_node = of_find_node_by_name(NULL,
+ "pmu-interrupt");
+ if (gpio_node && gpio_node->n_intrs > 0)
+ gpio_irq = gpio_node->intrs[0].line;
+
+ if (gpio_irq != -1) {
+ if (request_irq(gpio_irq, gpio1_interrupt, 0,
+ "GPIO1 ADB", (void *)0))
+ printk(KERN_ERR "pmu: can't get irq %d"
+ " (GPIO1)\n", gpio_irq);
+ else
+ gpio_irq_enabled = 1;
+ }
}
/* Enable interrupts */
@@ -1371,7 +1396,6 @@ next:
}
pmu_done(req);
} else {
-#if defined(CONFIG_XMON) && !defined(CONFIG_PPC64)
if (len == 4 && data[1] == 0x2c) {
extern int xmon_wants_key, xmon_adb_keycode;
if (xmon_wants_key) {
@@ -1379,7 +1403,6 @@ next:
return;
}
}
-#endif /* defined(CONFIG_XMON) && !defined(CONFIG_PPC64) */
#ifdef CONFIG_ADB
/*
* XXX On the [23]400 the PMU gives us an up
Index: linux-serialfix/arch/ppc/kernel/setup.c
===================================================================
--- linux-serialfix.orig/arch/ppc/kernel/setup.c 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/arch/ppc/kernel/setup.c 2005-11-23 16:54:25.000000000 +1100
@@ -744,6 +744,9 @@ void __init setup_arch(char **cmdline_p)
/* so udelay does something sensible, assume <= 1000 bogomips */
loops_per_jiffy = 500000000 / HZ;
+ if (ppc_md.init_early)
+ ppc_md.init_early();
+
#ifdef CONFIG_PPC_MULTIPLATFORM
/* This could be called "early setup arch", it must be done
* now because xmon need it
Index: linux-serialfix/include/asm-ppc/btext.h
===================================================================
--- linux-serialfix.orig/include/asm-ppc/btext.h 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/include/asm-ppc/btext.h 2005-11-23 16:54:25.000000000 +1100
@@ -17,7 +17,7 @@ extern unsigned long disp_BAT[2];
extern boot_infos_t disp_bi;
extern int boot_text_mapped;
-extern void init_boot_display(void);
+extern void btext_init(boot_infos_t *bi);
extern void btext_welcome(void);
extern void btext_prepare_BAT(void);
extern void btext_setup_display(int width, int height, int depth, int pitch,
Index: linux-serialfix/include/asm-ppc/machdep.h
===================================================================
--- linux-serialfix.orig/include/asm-ppc/machdep.h 2005-11-23 16:54:13.000000000 +1100
+++ linux-serialfix/include/asm-ppc/machdep.h 2005-11-23 16:54:25.000000000 +1100
@@ -35,8 +35,10 @@ struct machdep_calls {
int (*get_irq)(struct pt_regs *);
/* A general init function, called by ppc_init in init/main.c.
- May be NULL. */
+ May be NULL. DEPRECATED ! */
void (*init)(void);
+ /* For compatibility with merged platforms */
+ void (*init_early)(void);
void (*restart)(char *cmd);
void (*power_off)(void);
^ permalink raw reply
* [PATCH] powerpc: serial port discovery (#2)
From: Benjamin Herrenschmidt @ 2005-11-23 6:56 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc64-dev, linuxppc-dev list
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
This version fixes a bug with setting udbg on LPAR machines. We
need to force CON_ENABLED or the core will not register us because
of the add_preferred_console() calls. That itself triggered a bug
in unregister_console() that crashes when the console list is empty
(patch sent separately to Andrew).
Index: linux-serialfix/arch/powerpc/kernel/legacy_serial.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/kernel/legacy_serial.c 2005-11-23 17:30:14.000000000 +1100
@@ -0,0 +1,478 @@
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_core.h>
+#include <linux/console.h>
+#include <linux/pci.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <asm/prom.h>
+#include <asm/serial.h>
+#include <asm/udbg.h>
+#include <asm/pci-bridge.h>
+#include <asm/ppc-pci.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+#define MAX_LEGACY_SERIAL_PORTS 8
+
+static struct plat_serial8250_port
+legacy_serial_ports[MAX_LEGACY_SERIAL_PORTS+1];
+static struct legacy_serial_info {
+ struct device_node *np;
+ unsigned int speed;
+ unsigned int clock;
+ phys_addr_t taddr;
+} legacy_serial_infos[MAX_LEGACY_SERIAL_PORTS];
+static unsigned int legacy_serial_count;
+static int legacy_serial_console = -1;
+
+static int __init add_legacy_port(struct device_node *np, int want_index,
+ int iotype, phys_addr_t base,
+ phys_addr_t taddr, unsigned long irq)
+{
+ u32 *clk, *spd, clock;
+ int index;
+
+ /* get clock freq. if present */
+ clk = (u32 *)get_property(np, "clock-frequency", NULL);
+ clock = clk ? *clk : BASE_BAUD * 16;
+
+ /* get default speed if present */
+ spd = (u32 *)get_property(np, "current-speed", NULL);
+
+ /* If we have a location index, then try to use it */
+ if (want_index >= 0 && want_index < MAX_LEGACY_SERIAL_PORTS)
+ index = want_index;
+ else
+ index = legacy_serial_count;
+
+ /* if our index is still out of range, that mean that
+ * array is full, we could scan for a free slot but that
+ * make little sense to bother, just skip the port
+ */
+ if (index >= MAX_LEGACY_SERIAL_PORTS)
+ return -1;
+ if (index >= legacy_serial_count)
+ legacy_serial_count = index + 1;
+
+ /* Check if there is a port who already claimed our slot */
+ if (legacy_serial_infos[index].np != 0) {
+ /* if we still have some room, move it, else override */
+ if (legacy_serial_count < MAX_LEGACY_SERIAL_PORTS) {
+ printk(KERN_INFO "Moved legacy port %d -> %d\n",
+ index, legacy_serial_count);
+ legacy_serial_ports[legacy_serial_count] =
+ legacy_serial_ports[index];
+ legacy_serial_infos[legacy_serial_count] =
+ legacy_serial_infos[index];
+ legacy_serial_count++;
+ } else {
+ printk(KERN_INFO "Replacing legacy port %d\n", index);
+ }
+ }
+
+ /* Now fill the entry */
+ memset(&legacy_serial_ports[index], 0,
+ sizeof(struct plat_serial8250_port));
+ if (iotype == UPIO_PORT)
+ legacy_serial_ports[index].iobase = base;
+ else
+ legacy_serial_ports[index].membase = (void __iomem *)base;
+ legacy_serial_ports[index].iotype = iotype;
+ legacy_serial_ports[index].uartclk = clock;
+ legacy_serial_ports[index].irq = irq;
+ legacy_serial_ports[index].flags = ASYNC_BOOT_AUTOCONF;
+ legacy_serial_infos[index].taddr = taddr;
+ legacy_serial_infos[index].np = of_node_get(np);
+ legacy_serial_infos[index].clock = clock;
+ legacy_serial_infos[index].speed = spd ? *spd : 0;
+
+ printk(KERN_INFO "Found legacy serial port %d for %s\n",
+ index, np->full_name);
+ printk(KERN_INFO " %s=%llx, taddr=%llx, irq=%lx, clk=%d, speed=%d\n",
+ (iotype == UPIO_PORT) ? "port" : "mem",
+ (unsigned long long)base, (unsigned long long)taddr, irq,
+ legacy_serial_ports[index].uartclk,
+ legacy_serial_infos[index].speed);
+
+ return index;
+}
+
+static int __init add_legacy_isa_port(struct device_node *np,
+ struct device_node *isa_bridge)
+{
+ u32 *reg;
+ char *typep;
+ int index = -1;
+ phys_addr_t taddr;
+
+ /* Get the ISA port number */
+ reg = (u32 *)get_property(np, "reg", NULL);
+ if (reg == NULL)
+ return -1;
+
+ /* Verify it's an IO port, we don't support anything else */
+ if (!(reg[0] & 0x00000001))
+ return -1;
+
+ /* Now look for an "ibm,aix-loc" property that gives us ordering
+ * if any...
+ */
+ typep = (char *)get_property(np, "ibm,aix-loc", NULL);
+
+ /* If we have a location index, then use it */
+ if (typep && *typep == 'S')
+ index = simple_strtol(typep+1, NULL, 0) - 1;
+
+ /* Translate ISA address */
+ taddr = of_translate_address(np, reg);
+
+ /* Add port, irq will be dealt with later */
+ return add_legacy_port(np, index, UPIO_PORT, reg[1], taddr, NO_IRQ);
+
+}
+
+static int __init add_legacy_pci_port(struct device_node *np,
+ struct device_node *pci_dev)
+{
+ phys_addr_t addr, base;
+ u32 *addrp;
+ int iotype, index = -1;
+
+#if 0
+ /* We only support ports that have a clock frequency properly
+ * encoded in the device-tree (that is have an fcode). Anything
+ * else can't be used that early and will be normally probed by
+ * the generic 8250_pci driver later on.
+ */
+ if (get_property(np, "clock-frequency", NULL) == NULL)
+ return -1;
+#endif
+
+ /* Get the PCI address. Assume BAR 0 */
+ addrp = of_get_pci_address(pci_dev, 0, NULL);
+ if (addrp == NULL)
+ return -1;
+
+ /* We only support BAR 0 for now */
+ iotype = (addrp[0] & 0x02000000) ? UPIO_MEM : UPIO_PORT;
+ addr = of_translate_address(pci_dev, addrp);
+
+ /* Set the IO base to the same as the translated address for MMIO,
+ * or to the domain local IO base for PIO (it will be fixed up later)
+ */
+ if (iotype == UPIO_MEM)
+ base = addr;
+ else
+ base = addrp[2];
+
+ /* Try to guess an index... If we have subdevices of the pci dev,
+ * we get to their "reg" property
+ */
+ if (np != pci_dev) {
+ u32 *reg = (u32 *)get_property(np, "reg", NULL);
+ if (reg && (*reg < 4))
+ index = legacy_serial_count + *reg;
+ }
+
+ /* Add port, irq will be dealt with later. We passed a translated
+ * IO port value. It will be fixed up later along with the irq
+ */
+ return add_legacy_port(np, index, iotype, base, addr, NO_IRQ);
+}
+
+/*
+ * This is called very early, as part of setup_system() or eventually
+ * setup_arch(), basically before anything else in this file. This function
+ * will try to build a list of all the available 8250-compatible serial ports
+ * in the machine using the Open Firmware device-tree. It currently only deals
+ * with ISA and PCI busses but could be extended. It allows a very early boot
+ * console to be initialized, that list is also used later to provide 8250 with
+ * the machine non-PCI ports and to properly pick the default console port
+ */
+void __init find_legacy_serial_ports(void)
+{
+ struct device_node *np, *stdout;
+ char *path;
+ int index;
+
+ DBG(" -> find_legacy_serial_port()\n");
+
+ /* Now find out if one of these is out firmware console */
+ path = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
+ if (path == NULL) {
+ DBG(" no linux,stdout-path !\n");
+ return;
+ }
+ stdout = of_find_node_by_path(path);
+ if (stdout) {
+ DBG("stdout is %s\n", stdout->full_name);
+ }
+
+ /* First fill our array with ISA ports */
+ for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
+ struct device_node *isa = of_get_parent(np);
+ if (isa && !strcmp(isa->name, "isa")) {
+ index = add_legacy_isa_port(np, isa);
+ if (index >= 0 && np == stdout)
+ legacy_serial_console = index;
+ }
+ of_node_put(isa);
+ }
+
+ /* Next, try to locate PCI ports */
+ for (np = NULL; (np = of_find_all_nodes(np));) {
+ struct device_node *pci, *parent = of_get_parent(np);
+ if (parent && !strcmp(parent->name, "isa")) {
+ of_node_put(parent);
+ continue;
+ }
+ if (strcmp(np->name, "serial") && strcmp(np->type, "serial")) {
+ of_node_put(parent);
+ continue;
+ }
+ /* Check for known pciclass, and also check wether we have
+ * a device with child nodes for ports or not
+ */
+ if (device_is_compatible(np, "pciclass,0700") ||
+ device_is_compatible(np, "pciclass,070002"))
+ pci = np;
+ else if (device_is_compatible(parent, "pciclass,0700") ||
+ device_is_compatible(parent, "pciclass,070002"))
+ pci = parent;
+ else {
+ of_node_put(parent);
+ continue;
+ }
+ index = add_legacy_pci_port(np, pci);
+ if (index >= 0 && np == stdout)
+ legacy_serial_console = index;
+ of_node_put(parent);
+ }
+
+ DBG("legacy_serial_console = %d\n", legacy_serial_console);
+
+ /* udbg is 64 bits only for now, that will change soon though ... */
+#ifdef CONFIG_PPC64
+ while (legacy_serial_console >= 0) {
+ struct legacy_serial_info *info =
+ &legacy_serial_infos[legacy_serial_console];
+ void __iomem *addr;
+
+ if (info->taddr == 0)
+ break;
+ addr = ioremap(info->taddr, 0x1000);
+ if (addr == NULL)
+ break;
+ if (info->speed == 0)
+ info->speed = udbg_probe_uart_speed(addr, info->clock);
+ DBG("default console speed = %d\n", info->speed);
+ udbg_init_uart(addr, info->speed, info->clock);
+ break;
+ }
+#endif /* CONFIG_PPC64 */
+
+ DBG(" <- find_legacy_serial_port()\n");
+}
+
+static struct platform_device serial_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = legacy_serial_ports,
+ },
+};
+
+static void __init fixup_port_irq(int index,
+ struct device_node *np,
+ struct plat_serial8250_port *port)
+{
+ DBG("fixup_port_irq(%d)\n", index);
+
+ /* Check for interrupts in that node */
+ if (np->n_intrs > 0) {
+ port->irq = np->intrs[0].line;
+ DBG(" port %d (%s), irq=%d\n",
+ index, np->full_name, port->irq);
+ return;
+ }
+
+ /* Check for interrupts in the parent */
+ np = of_get_parent(np);
+ if (np == NULL)
+ return;
+
+ if (np->n_intrs > 0) {
+ port->irq = np->intrs[0].line;
+ DBG(" port %d (%s), irq=%d\n",
+ index, np->full_name, port->irq);
+ }
+ of_node_put(np);
+}
+
+static void __init fixup_port_pio(int index,
+ struct device_node *np,
+ struct plat_serial8250_port *port)
+{
+ struct pci_controller *hose;
+
+ DBG("fixup_port_pio(%d)\n", index);
+
+ hose = pci_find_hose_for_OF_device(np);
+ if (hose) {
+ unsigned long offset = (unsigned long)hose->io_base_virt -
+#ifdef CONFIG_PPC64
+ pci_io_base;
+#else
+ isa_io_base;
+#endif
+ DBG("port %d, IO %lx -> %lx\n",
+ index, port->iobase, port->iobase + offset);
+ port->iobase += offset;
+ }
+}
+
+/*
+ * This is called as an arch initcall, hopefully before the PCI bus is
+ * probed and/or the 8250 driver loaded since we need to register our
+ * platform devices before 8250 PCI ones are detected as some of them
+ * must properly "override" the platform ones.
+ *
+ * This function fixes up the interrupt value for platform ports as it
+ * couldn't be done earlier before interrupt maps have been parsed. It
+ * also "corrects" the IO address for PIO ports for the same reason,
+ * since earlier, the PHBs virtual IO space wasn't assigned yet. It then
+ * registers all those platform ports for use by the 8250 driver when it
+ * finally loads.
+ */
+static int __init serial_dev_init(void)
+{
+ int i;
+
+ if (legacy_serial_count == 0)
+ return -ENODEV;
+
+ /*
+ * Before we register the platfrom serial devices, we need
+ * to fixup their interrutps and their IO ports.
+ */
+ DBG("Fixing serial ports interrupts and IO ports ...\n");
+
+ for (i = 0; i < legacy_serial_count; i++) {
+ struct plat_serial8250_port *port = &legacy_serial_ports[i];
+ struct device_node *np = legacy_serial_infos[i].np;
+
+ if (port->irq == NO_IRQ)
+ fixup_port_irq(i, np, port);
+ if (port->iotype == UPIO_PORT)
+ fixup_port_pio(i, np, port);
+ }
+
+ DBG("Registering platform serial ports\n");
+
+ return platform_device_register(&serial_device);
+}
+arch_initcall(serial_dev_init);
+
+
+/*
+ * This is called very early, as part of console_init() (typically just after
+ * time_init()). This function is respondible for trying to find a good
+ * default console on serial ports. It tries to match the open firmware
+ * default output with one of the available serial console drivers, either
+ * one of the platform serial ports that have been probed earlier by
+ * find_legacy_serial_ports() or some more platform specific ones.
+ */
+static int __init check_legacy_serial_console(void)
+{
+ struct device_node *prom_stdout = NULL;
+ int speed = 0, offset = 0;
+ char *name;
+ u32 *spd;
+
+ DBG(" -> check_legacy_serial_console()\n");
+
+ /* The user has requested a console so this is already set up. */
+ if (strstr(saved_command_line, "console=")) {
+ DBG(" console was specified !\n");
+ return -EBUSY;
+ }
+
+ if (!of_chosen) {
+ DBG(" of_chosen is NULL !\n");
+ return -ENODEV;
+ }
+ /* We are getting a weird phandle from OF ... */
+ /* ... So use the full path instead */
+ name = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
+ if (name == NULL) {
+ DBG(" no linux,stdout-path !\n");
+ return -ENODEV;
+ }
+ prom_stdout = of_find_node_by_path(name);
+ if (!prom_stdout) {
+ DBG(" can't find stdout package %s !\n", name);
+ return -ENODEV;
+ }
+ DBG("stdout is %s\n", prom_stdout->full_name);
+
+ name = (char *)get_property(prom_stdout, "name", NULL);
+ if (!name) {
+ DBG(" stdout package has no name !\n");
+ goto not_found;
+ }
+ spd = (u32 *)get_property(prom_stdout, "current-speed", NULL);
+ if (spd)
+ speed = *spd;
+
+ if (0)
+ ;
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+ else if (strcmp(name, "serial") == 0) {
+ int i;
+ /* Look for it in probed array */
+ for (i = 0; i < legacy_serial_count; i++) {
+ if (prom_stdout != legacy_serial_infos[i].np)
+ continue;
+ offset = i;
+ speed = legacy_serial_infos[i].speed;
+ break;
+ }
+ if (i >= legacy_serial_count)
+ goto not_found;
+ }
+#endif /* CONFIG_SERIAL_8250_CONSOLE */
+#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
+ else if (strcmp(name, "ch-a") == 0)
+ offset = 0;
+ else if (strcmp(name, "ch-b") == 0)
+ offset = 1;
+#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
+ else
+ goto not_found;
+ of_node_put(prom_stdout);
+
+ DBG("Found serial console at ttyS%d\n", offset);
+
+ if (speed) {
+ static char __initdata opt[16];
+ sprintf(opt, "%d", speed);
+ return add_preferred_console("ttyS", offset, opt);
+ } else
+ return add_preferred_console("ttyS", offset, NULL);
+
+ not_found:
+ DBG("No preferred console found !\n");
+ of_node_put(prom_stdout);
+ return -ENODEV;
+}
+console_initcall(check_legacy_serial_console);
+
Index: linux-serialfix/arch/powerpc/kernel/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/Makefile 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/Makefile 2005-11-23 17:40:02.000000000 +1100
@@ -32,10 +32,6 @@ obj-$(CONFIG_RTAS_PROC) += rtas-proc.o
obj-$(CONFIG_LPARCFG) += lparcfg.o
obj-$(CONFIG_IBMVIO) += vio.o
obj-$(CONFIG_GENERIC_TBSYNC) += smp-tbsync.o
-obj-$(CONFIG_PPC_PSERIES) += udbg_16550.o
-obj-$(CONFIG_PPC_MAPLE) += udbg_16550.o
-udbgscc-$(CONFIG_PPC64) := udbg_scc.o
-obj-$(CONFIG_PPC_PMAC) += $(udbgscc-y)
obj64-$(CONFIG_PPC_MULTIPLATFORM) += nvram_64.o
ifeq ($(CONFIG_PPC_MERGE),y)
@@ -58,14 +54,15 @@ obj-$(CONFIG_BOOTX_TEXT) += btext.o
obj-$(CONFIG_6xx) += idle_6xx.o
obj-$(CONFIG_SMP) += smp.o
obj-$(CONFIG_KPROBES) += kprobes.o
-
+obj-$(CONFIG_PPC_MULTIPLATFORM) += legacy_serial.o
+obj64-$(CONFIG_PPC_MULTIPLATFORM) += udbg_16550.o
+obj64-$(CONFIG_PPC_PMAC) += udbg_scc.o
module-$(CONFIG_PPC64) += module_64.o
obj-$(CONFIG_MODULES) += $(module-y)
pci64-$(CONFIG_PPC64) += pci_64.o pci_dn.o pci_iommu.o \
pci_direct_iommu.o iomap.o
obj-$(CONFIG_PCI) += $(pci64-y)
-
kexec64-$(CONFIG_PPC64) += machine_kexec_64.o
obj-$(CONFIG_KEXEC) += $(kexec64-y)
Index: linux-serialfix/arch/powerpc/kernel/setup-common.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/setup-common.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/setup-common.c 2005-11-23 17:30:14.000000000 +1100
@@ -294,129 +294,6 @@ struct seq_operations cpuinfo_op = {
.show = show_cpuinfo,
};
-#ifdef CONFIG_PPC_MULTIPLATFORM
-static int __init set_preferred_console(void)
-{
- struct device_node *prom_stdout = NULL;
- char *name;
- u32 *spd;
- int offset = 0;
-
- DBG(" -> set_preferred_console()\n");
-
- /* The user has requested a console so this is already set up. */
- if (strstr(saved_command_line, "console=")) {
- DBG(" console was specified !\n");
- return -EBUSY;
- }
-
- if (!of_chosen) {
- DBG(" of_chosen is NULL !\n");
- return -ENODEV;
- }
- /* We are getting a weird phandle from OF ... */
- /* ... So use the full path instead */
- name = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
- if (name == NULL) {
- DBG(" no linux,stdout-path !\n");
- return -ENODEV;
- }
- prom_stdout = of_find_node_by_path(name);
- if (!prom_stdout) {
- DBG(" can't find stdout package %s !\n", name);
- return -ENODEV;
- }
- DBG("stdout is %s\n", prom_stdout->full_name);
-
- name = (char *)get_property(prom_stdout, "name", NULL);
- if (!name) {
- DBG(" stdout package has no name !\n");
- goto not_found;
- }
- spd = (u32 *)get_property(prom_stdout, "current-speed", NULL);
-
- if (0)
- ;
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- else if (strcmp(name, "serial") == 0) {
- int i;
- u32 *reg = (u32 *)get_property(prom_stdout, "reg", &i);
- if (i > 8) {
- switch (reg[1]) {
- case 0x3f8:
- offset = 0;
- break;
- case 0x2f8:
- offset = 1;
- break;
- case 0x898:
- offset = 2;
- break;
- case 0x890:
- offset = 3;
- break;
- default:
- /* We dont recognise the serial port */
- goto not_found;
- }
- }
- }
-#endif /* CONFIG_SERIAL_8250_CONSOLE */
-#ifdef CONFIG_PPC_PSERIES
- else if (strcmp(name, "vty") == 0) {
- u32 *reg = (u32 *)get_property(prom_stdout, "reg", NULL);
- char *compat = (char *)get_property(prom_stdout, "compatible", NULL);
-
- if (reg && compat && (strcmp(compat, "hvterm-protocol") == 0)) {
- /* Host Virtual Serial Interface */
- switch (reg[0]) {
- case 0x30000000:
- offset = 0;
- break;
- case 0x30000001:
- offset = 1;
- break;
- default:
- goto not_found;
- }
- of_node_put(prom_stdout);
- DBG("Found hvsi console at offset %d\n", offset);
- return add_preferred_console("hvsi", offset, NULL);
- } else {
- /* pSeries LPAR virtual console */
- of_node_put(prom_stdout);
- DBG("Found hvc console\n");
- return add_preferred_console("hvc", 0, NULL);
- }
- }
-#endif /* CONFIG_PPC_PSERIES */
-#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
- else if (strcmp(name, "ch-a") == 0)
- offset = 0;
- else if (strcmp(name, "ch-b") == 0)
- offset = 1;
-#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
- else
- goto not_found;
- of_node_put(prom_stdout);
-
- DBG("Found serial console at ttyS%d\n", offset);
-
- if (spd) {
- static char __initdata opt[16];
- sprintf(opt, "%d", *spd);
- return add_preferred_console("ttyS", offset, opt);
- } else
- return add_preferred_console("ttyS", offset, NULL);
-
- not_found:
- DBG("No preferred console found !\n");
- of_node_put(prom_stdout);
- return -ENODEV;
-}
-console_initcall(set_preferred_console);
-#endif /* CONFIG_PPC_MULTIPLATFORM */
-
void __init check_for_initrd(void)
{
#ifdef CONFIG_BLK_DEV_INITRD
Index: linux-serialfix/arch/powerpc/kernel/setup_64.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/setup_64.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/setup_64.c 2005-11-23 17:40:02.000000000 +1100
@@ -451,6 +451,15 @@ void __init setup_system(void)
*/
ppc_md.init_early();
+ /*
+ * We can discover serial ports now since the above did setup the
+ * hash table management for us, thus ioremap works. We do that early
+ * so that further code can be debugged
+ */
+#ifdef CONFIG_PPC_MULTIPLATFORM
+ find_legacy_serial_ports();
+#endif
+
/*
* "Finish" the device-tree, that is do the actual parsing of
* some of the properties like the interrupt map
@@ -649,187 +658,6 @@ void ppc64_terminate_msg(unsigned int sr
printk("[terminate]%04x %s\n", src, msg);
}
-#ifndef CONFIG_PPC_ISERIES
-/*
- * This function can be used by platforms to "find" legacy serial ports.
- * It works for "serial" nodes under an "isa" node, and will try to
- * respect the "ibm,aix-loc" property if any. It works with up to 8
- * ports.
- */
-
-#define MAX_LEGACY_SERIAL_PORTS 8
-static struct plat_serial8250_port serial_ports[MAX_LEGACY_SERIAL_PORTS+1];
-static unsigned int old_serial_count;
-
-void __init generic_find_legacy_serial_ports(u64 *physport,
- unsigned int *default_speed)
-{
- struct device_node *np;
- u32 *sizeprop;
-
- struct isa_reg_property {
- u32 space;
- u32 address;
- u32 size;
- };
- struct pci_reg_property {
- struct pci_address addr;
- u32 size_hi;
- u32 size_lo;
- };
-
- DBG(" -> generic_find_legacy_serial_port()\n");
-
- *physport = 0;
- if (default_speed)
- *default_speed = 0;
-
- np = of_find_node_by_path("/");
- if (!np)
- return;
-
- /* First fill our array */
- for (np = NULL; (np = of_find_node_by_type(np, "serial"));) {
- struct device_node *isa, *pci;
- struct isa_reg_property *reg;
- unsigned long phys_size, addr_size, io_base;
- u32 *rangesp;
- u32 *interrupts, *clk, *spd;
- char *typep;
- int index, rlen, rentsize;
-
- /* Ok, first check if it's under an "isa" parent */
- isa = of_get_parent(np);
- if (!isa || strcmp(isa->name, "isa")) {
- DBG("%s: no isa parent found\n", np->full_name);
- continue;
- }
-
- /* Now look for an "ibm,aix-loc" property that gives us ordering
- * if any...
- */
- typep = (char *)get_property(np, "ibm,aix-loc", NULL);
-
- /* Get the ISA port number */
- reg = (struct isa_reg_property *)get_property(np, "reg", NULL);
- if (reg == NULL)
- goto next_port;
- /* We assume the interrupt number isn't translated ... */
- interrupts = (u32 *)get_property(np, "interrupts", NULL);
- /* get clock freq. if present */
- clk = (u32 *)get_property(np, "clock-frequency", NULL);
- /* get default speed if present */
- spd = (u32 *)get_property(np, "current-speed", NULL);
- /* Default to locate at end of array */
- index = old_serial_count; /* end of the array by default */
-
- /* If we have a location index, then use it */
- if (typep && *typep == 'S') {
- index = simple_strtol(typep+1, NULL, 0) - 1;
- /* if index is out of range, use end of array instead */
- if (index >= MAX_LEGACY_SERIAL_PORTS)
- index = old_serial_count;
- /* if our index is still out of range, that mean that
- * array is full, we could scan for a free slot but that
- * make little sense to bother, just skip the port
- */
- if (index >= MAX_LEGACY_SERIAL_PORTS)
- goto next_port;
- if (index >= old_serial_count)
- old_serial_count = index + 1;
- /* Check if there is a port who already claimed our slot */
- if (serial_ports[index].iobase != 0) {
- /* if we still have some room, move it, else override */
- if (old_serial_count < MAX_LEGACY_SERIAL_PORTS) {
- DBG("Moved legacy port %d -> %d\n", index,
- old_serial_count);
- serial_ports[old_serial_count++] =
- serial_ports[index];
- } else {
- DBG("Replacing legacy port %d\n", index);
- }
- }
- }
- if (index >= MAX_LEGACY_SERIAL_PORTS)
- goto next_port;
- if (index >= old_serial_count)
- old_serial_count = index + 1;
-
- /* Now fill the entry */
- memset(&serial_ports[index], 0, sizeof(struct plat_serial8250_port));
- serial_ports[index].uartclk = clk ? *clk : BASE_BAUD * 16;
- serial_ports[index].iobase = reg->address;
- serial_ports[index].irq = interrupts ? interrupts[0] : 0;
- serial_ports[index].flags = ASYNC_BOOT_AUTOCONF;
-
- DBG("Added legacy port, index: %d, port: %x, irq: %d, clk: %d\n",
- index,
- serial_ports[index].iobase,
- serial_ports[index].irq,
- serial_ports[index].uartclk);
-
- /* Get phys address of IO reg for port 1 */
- if (index != 0)
- goto next_port;
-
- pci = of_get_parent(isa);
- if (!pci) {
- DBG("%s: no pci parent found\n", np->full_name);
- goto next_port;
- }
-
- rangesp = (u32 *)get_property(pci, "ranges", &rlen);
- if (rangesp == NULL) {
- of_node_put(pci);
- goto next_port;
- }
- rlen /= 4;
-
- /* we need the #size-cells of the PCI bridge node itself */
- phys_size = 1;
- sizeprop = (u32 *)get_property(pci, "#size-cells", NULL);
- if (sizeprop != NULL)
- phys_size = *sizeprop;
- /* we need the parent #addr-cells */
- addr_size = prom_n_addr_cells(pci);
- rentsize = 3 + addr_size + phys_size;
- io_base = 0;
- for (;rlen >= rentsize; rlen -= rentsize,rangesp += rentsize) {
- if (((rangesp[0] >> 24) & 0x3) != 1)
- continue; /* not IO space */
- io_base = rangesp[3];
- if (addr_size == 2)
- io_base = (io_base << 32) | rangesp[4];
- }
- if (io_base != 0) {
- *physport = io_base + reg->address;
- if (default_speed && spd)
- *default_speed = *spd;
- }
- of_node_put(pci);
- next_port:
- of_node_put(isa);
- }
-
- DBG(" <- generic_find_legacy_serial_port()\n");
-}
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = serial_ports,
- },
-};
-
-static int __init serial_dev_init(void)
-{
- return platform_device_register(&serial_device);
-}
-arch_initcall(serial_dev_init);
-
-#endif /* CONFIG_PPC_ISERIES */
-
int check_legacy_ioport(unsigned long base_port)
{
if (ppc_md.check_legacy_ioport == NULL)
Index: linux-serialfix/arch/powerpc/kernel/udbg_16550.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/udbg_16550.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/udbg_16550.c 2005-11-23 17:40:02.000000000 +1100
@@ -43,6 +43,8 @@ struct NS16550 {
#define LSR_TEMT 0x40 /* Xmitter empty */
#define LSR_ERR 0x80 /* Error */
+#define LCR_DLAB 0x80
+
static volatile struct NS16550 __iomem *udbg_comport;
static void udbg_550_putc(unsigned char c)
@@ -77,29 +79,70 @@ static unsigned char udbg_550_getc(void)
return 0;
}
-void udbg_init_uart(void __iomem *comport, unsigned int speed)
+void udbg_init_uart(void __iomem *comport, unsigned int speed,
+ unsigned int clock)
{
- u16 dll = speed ? (115200 / speed) : 12;
+ unsigned int dll, base_bauds = clock / 16;
+
+ if (speed == 0)
+ speed = 9600;
+ dll = base_bauds / speed;
if (comport) {
udbg_comport = (struct NS16550 __iomem *)comport;
out_8(&udbg_comport->lcr, 0x00);
out_8(&udbg_comport->ier, 0xff);
out_8(&udbg_comport->ier, 0x00);
- out_8(&udbg_comport->lcr, 0x80); /* Access baud rate */
- out_8(&udbg_comport->dll, dll & 0xff); /* 1 = 115200, 2 = 57600,
- 3 = 38400, 12 = 9600 baud */
- out_8(&udbg_comport->dlm, dll >> 8); /* dll >> 8 which should be zero
- for fast rates; */
- out_8(&udbg_comport->lcr, 0x03); /* 8 data, 1 stop, no parity */
- out_8(&udbg_comport->mcr, 0x03); /* RTS/DTR */
- out_8(&udbg_comport->fcr ,0x07); /* Clear & enable FIFOs */
+ out_8(&udbg_comport->lcr, LCR_DLAB);
+ out_8(&udbg_comport->dll, dll & 0xff);
+ out_8(&udbg_comport->dlm, dll >> 8);
+ /* 8 data, 1 stop, no parity */
+ out_8(&udbg_comport->lcr, 0x03);
+ /* RTS/DTR */
+ out_8(&udbg_comport->mcr, 0x03);
+ /* Clear & enable FIFOs */
+ out_8(&udbg_comport->fcr ,0x07);
udbg_putc = udbg_550_putc;
udbg_getc = udbg_550_getc;
udbg_getc_poll = udbg_550_getc_poll;
}
}
+unsigned int udbg_probe_uart_speed(void __iomem *comport, unsigned int clock)
+{
+ unsigned int dll, dlm, divisor, prescaler, speed;
+ u8 old_lcr;
+ volatile struct NS16550 __iomem *port = comport;
+
+ old_lcr = in_8(&port->lcr);
+
+ /* select divisor latch registers. */
+ out_8(&port->lcr, LCR_DLAB);
+
+ /* now, read the divisor */
+ dll = in_8(&port->dll);
+ dlm = in_8(&port->dlm);
+ divisor = dlm << 8 | dll;
+
+ /* check prescaling */
+ if (in_8(&port->mcr) & 0x80)
+ prescaler = 4;
+ else
+ prescaler = 1;
+
+ /* restore the LCR */
+ out_8(&port->lcr, old_lcr);
+
+ /* calculate speed */
+ speed = (clock / prescaler) / (divisor * 16);
+
+ /* sanity check */
+ if (speed < 9600 || speed > 115200)
+ speed = 9600;
+
+ return speed;
+}
+
#ifdef CONFIG_PPC_MAPLE
void udbg_maple_real_putc(unsigned char c)
{
Index: linux-serialfix/arch/powerpc/platforms/maple/setup.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/maple/setup.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/maple/setup.c 2005-11-23 17:30:14.000000000 +1100
@@ -191,20 +191,6 @@ static void __init maple_init_early(void
*/
hpte_init_native();
- /* Find the serial port */
- generic_find_legacy_serial_ports(&physport, &default_speed);
-
- DBG("phys port addr: %lx\n", (long)physport);
-
- if (physport) {
- void *comport;
- /* Map the uart for udbg. */
- comport = (void *)ioremap(physport, 16);
- udbg_init_uart(comport, default_speed);
-
- DBG("Hello World !\n");
- }
-
/* Setup interrupt mapping options */
ppc64_interrupt_controller = IC_OPEN_PIC;
Index: linux-serialfix/arch/powerpc/platforms/pseries/lpar.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/pseries/lpar.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/pseries/lpar.c 2005-11-23 17:40:02.000000000 +1100
@@ -24,6 +24,7 @@
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/dma-mapping.h>
+#include <linux/console.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/page.h>
@@ -191,7 +192,7 @@ static unsigned char udbg_getcLP(void)
/* call this from early_init() for a working debug console on
* vterm capable LPAR machines
*/
-void udbg_init_debug_lpar(void)
+void __init udbg_init_debug_lpar(void)
{
vtermno = 0;
udbg_putc = udbg_putcLP;
@@ -200,63 +201,54 @@ void udbg_init_debug_lpar(void)
}
/* returns 0 if couldn't find or use /chosen/stdout as console */
-int find_udbg_vterm(void)
+void __init find_udbg_vterm(void)
{
struct device_node *stdout_node;
u32 *termno;
char *name;
- int found = 0;
+ int add_console;
/* find the boot console from /chosen/stdout */
if (!of_chosen)
- return 0;
+ return;
name = (char *)get_property(of_chosen, "linux,stdout-path", NULL);
if (name == NULL)
- return 0;
+ return;
stdout_node = of_find_node_by_path(name);
if (!stdout_node)
- return 0;
-
- /* now we have the stdout node; figure out what type of device it is. */
+ return;
name = (char *)get_property(stdout_node, "name", NULL);
if (!name) {
printk(KERN_WARNING "stdout node missing 'name' property!\n");
goto out;
}
+ /* The user has requested a console so this is already set up. */
+ add_console = !strstr(cmd_line, "console=");
- if (strncmp(name, "vty", 3) == 0) {
- if (device_is_compatible(stdout_node, "hvterm1")) {
- termno = (u32 *)get_property(stdout_node, "reg", NULL);
- if (termno) {
- vtermno = termno[0];
- udbg_putc = udbg_putcLP;
- udbg_getc = udbg_getcLP;
- udbg_getc_poll = udbg_getc_pollLP;
- found = 1;
- }
- } else if (device_is_compatible(stdout_node, "hvterm-protocol")) {
- termno = (u32 *)get_property(stdout_node, "reg", NULL);
- if (termno) {
- vtermno = termno[0];
- udbg_putc = udbg_hvsi_putc;
- udbg_getc = udbg_hvsi_getc;
- udbg_getc_poll = udbg_hvsi_getc_poll;
- found = 1;
- }
- }
- } else if (strncmp(name, "serial", 6)) {
- /* XXX fix ISA serial console */
- printk(KERN_WARNING "serial stdout on LPAR ('%s')! "
- "can't print udbg messages\n",
- stdout_node->full_name);
- } else {
- printk(KERN_WARNING "don't know how to print to stdout '%s'\n",
- stdout_node->full_name);
- }
+ /* Check if it's a virtual terminal */
+ if (strncmp(name, "vty", 3) != 0)
+ goto out;
+ termno = (u32 *)get_property(stdout_node, "reg", NULL);
+ if (termno == NULL)
+ goto out;
+ vtermno = termno[0];
+ if (device_is_compatible(stdout_node, "hvterm1")) {
+ udbg_putc = udbg_putcLP;
+ udbg_getc = udbg_getcLP;
+ udbg_getc_poll = udbg_getc_pollLP;
+ if (add_console)
+ add_preferred_console("hvc", termno[0] & 0xff, NULL);
+ } else if (device_is_compatible(stdout_node, "hvterm-protocol")) {
+ vtermno = termno[0];
+ udbg_putc = udbg_hvsi_putc;
+ udbg_getc = udbg_hvsi_getc;
+ udbg_getc_poll = udbg_hvsi_getc_poll;
+ if (add_console)
+ add_preferred_console("hvsi", termno[0] & 0xff, NULL);
+ }
out:
of_node_put(stdout_node);
- return found;
}
void vpa_init(int cpu)
Index: linux-serialfix/arch/powerpc/platforms/pseries/setup.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/platforms/pseries/setup.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/platforms/pseries/setup.c 2005-11-23 17:30:14.000000000 +1100
@@ -78,8 +78,6 @@
extern void find_udbg_vterm(void);
extern void system_reset_fwnmi(void); /* from head.S */
extern void machine_check_fwnmi(void); /* from head.S */
-extern void generic_find_legacy_serial_ports(u64 *physport,
- unsigned int *default_speed);
int fwnmi_active; /* TRUE if an FWNMI handler is present */
@@ -365,10 +363,7 @@ static int pseries_set_xdabr(unsigned lo
*/
static void __init pSeries_init_early(void)
{
- void *comport;
int iommu_off = 0;
- unsigned int default_speed;
- u64 physport;
DBG(" -> pSeries_init_early()\n");
@@ -382,17 +377,8 @@ static void __init pSeries_init_early(vo
get_property(of_chosen, "linux,iommu-off", NULL));
}
- generic_find_legacy_serial_ports(&physport, &default_speed);
-
if (platform_is_lpar())
find_udbg_vterm();
- else if (physport) {
- /* Map the uart for udbg. */
- comport = (void *)ioremap(physport, 16);
- udbg_init_uart(comport, default_speed);
-
- DBG("Hello World !\n");
- }
if (firmware_has_feature(FW_FEATURE_DABR))
ppc_md.set_dabr = pseries_set_dabr;
Index: linux-serialfix/include/asm-powerpc/serial.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/serial.h 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/serial.h 2005-11-23 17:30:14.000000000 +1100
@@ -15,4 +15,6 @@
/* Default baud base if not found in device-tree */
#define BASE_BAUD ( 1843200 / 16 )
+extern void find_legacy_serial_ports(void);
+
#endif /* _PPC64_SERIAL_H */
Index: linux-serialfix/include/asm-powerpc/udbg.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/udbg.h 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/udbg.h 2005-11-23 17:40:02.000000000 +1100
@@ -24,7 +24,10 @@ extern int udbg_read(char *buf, int bufl
extern void register_early_udbg_console(void);
extern void udbg_printf(const char *fmt, ...);
-extern void udbg_init_uart(void __iomem *comport, unsigned int speed);
+extern void udbg_init_uart(void __iomem *comport, unsigned int speed,
+ unsigned int clock);
+extern unsigned int udbg_probe_uart_speed(void __iomem *comport,
+ unsigned int clock);
struct device_node;
extern void udbg_init_scc(struct device_node *np);
Index: linux-serialfix/arch/powerpc/kernel/setup_32.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/setup_32.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/setup_32.c 2005-11-23 17:40:02.000000000 +1100
@@ -39,6 +39,7 @@
#include <asm/nvram.h>
#include <asm/xmon.h>
#include <asm/time.h>
+#include <asm/serial.h>
#include "setup.h"
@@ -282,6 +283,13 @@ void __init setup_arch(char **cmdline_p)
unflatten_device_tree();
check_for_initrd();
+
+ if (ppc_md.init_early)
+ ppc_md.init_early();
+
+#ifdef CONFIG_PPC_MULTIPLATFORM
+ find_legacy_serial_ports();
+#endif
finish_device_tree();
smp_setup_cpu_maps();
Index: linux-serialfix/arch/powerpc/kernel/pci_64.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/pci_64.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/pci_64.c 2005-11-23 17:30:14.000000000 +1100
@@ -1223,6 +1223,7 @@ void __devinit pcibios_fixup_device_reso
}
EXPORT_SYMBOL(pcibios_fixup_device_resources);
+
static void __devinit do_bus_setup(struct pci_bus *bus)
{
struct pci_dev *dev;
@@ -1306,6 +1307,20 @@ void pci_resource_to_user(const struct p
*end = rsrc->end + offset;
}
+struct pci_controller* pci_find_hose_for_OF_device(struct device_node* node)
+{
+ if (!have_of)
+ return NULL;
+ while(node) {
+ struct pci_controller *hose, *tmp;
+ list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
+ if (hose->arch_data == node)
+ return hose;
+ node = node->parent;
+ }
+ return NULL;
+}
+
#endif /* CONFIG_PPC_MULTIPLATFORM */
Index: linux-serialfix/arch/ppc/kernel/pci.c
===================================================================
--- linux-serialfix.orig/arch/ppc/kernel/pci.c 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/arch/ppc/kernel/pci.c 2005-11-23 17:30:14.000000000 +1100
@@ -815,8 +815,7 @@ EXPORT_SYMBOL(pci_device_to_OF_node);
* to set pci_assign_all_buses to 1 and still use RTAS for PCI
* config cycles.
*/
-struct pci_controller*
-pci_find_hose_for_OF_device(struct device_node* node)
+struct pci_controller* pci_find_hose_for_OF_device(struct device_node* node)
{
if (!have_of)
return NULL;
Index: linux-serialfix/include/asm-powerpc/pci-bridge.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/pci-bridge.h 2005-11-23 17:25:11.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/pci-bridge.h 2005-11-23 17:30:14.000000000 +1100
@@ -140,6 +140,9 @@ static inline struct pci_controller *pci
return PCI_DN(busdn)->phb;
}
+extern struct pci_controller*
+pci_find_hose_for_OF_device(struct device_node* node);
+
extern struct pci_controller *
pcibios_alloc_controller(struct device_node *dev);
extern void pcibios_free_controller(struct pci_controller *phb);
Index: linux-serialfix/arch/powerpc/kernel/udbg.c
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/udbg.c 2005-11-23 17:40:02.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/udbg.c 2005-11-23 17:46:27.000000000 +1100
@@ -99,7 +99,7 @@ static void udbg_console_write(struct co
static struct console udbg_console = {
.name = "udbg",
.write = udbg_console_write,
- .flags = CON_PRINTBUFFER,
+ .flags = CON_PRINTBUFFER | CON_ENABLED,
.index = -1,
};
^ permalink raw reply
* [PATCH] powerpc: Add OF address parsing code (#2)
From: Benjamin Herrenschmidt @ 2005-11-23 6:53 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc64-dev, linuxppc-dev list
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
This version fixes handling of empty "ranges" properties and adds
a more generic of_get_address().
Index: linux-serialfix/arch/powerpc/kernel/Makefile
===================================================================
--- linux-serialfix.orig/arch/powerpc/kernel/Makefile 2005-11-23 16:54:14.000000000 +1100
+++ linux-serialfix/arch/powerpc/kernel/Makefile 2005-11-23 16:54:24.000000000 +1100
@@ -12,7 +12,8 @@ CFLAGS_btext.o += -fPIC
endif
obj-y := semaphore.o cputable.o ptrace.o syscalls.o \
- irq.o align.o signal_32.o pmc.o vdso.o
+ irq.o align.o signal_32.o pmc.o vdso.o \
+ prom_parse.o
obj-y += vdso32/
obj-$(CONFIG_PPC64) += setup_64.o binfmt_elf32.o sys_ppc32.o \
signal_64.o ptrace32.o systbl.o \
Index: linux-serialfix/arch/powerpc/kernel/prom_parse.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-serialfix/arch/powerpc/kernel/prom_parse.c 2005-11-23 16:54:24.000000000 +1100
@@ -0,0 +1,420 @@
+#undef DEBUG
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/pci_regs.h>
+#include <linux/module.h>
+#include <asm/prom.h>
+
+#ifdef DEBUG
+#define DBG(fmt...) do { printk(fmt); } while(0)
+#else
+#define DBG(fmt...) do { } while(0)
+#endif
+
+#ifdef CONFIG_PPC64
+#define PRu64 "%lx"
+#else
+#define PRu64 "%llx"
+#endif
+
+/* Max address size we deal with */
+#define OF_MAX_ADDR_CELLS 4
+#define OF_CHECK_COUNTS(na, ns) ((na) > 0 && (na) <= OF_MAX_ADDR_CELLS && \
+ (ns) > 0)
+
+/* Debug utility */
+#ifdef DEBUG
+static void of_dump_addr(const char *s, u32 *addr, int na)
+{
+ printk("%s", s);
+ while(na--)
+ printk(" %08x", *(addr++));
+ printk("\n");
+}
+#else
+static void of_dump_addr(const char *s, u32 *addr, int na) { }
+#endif
+
+/* Read a big address */
+static inline u64 of_read_addr(u32 *cell, int size)
+{
+ u64 r = 0;
+ while (size--)
+ r = (r << 32) | *(cell++);
+ return r;
+}
+
+/* Callbacks for bus specific translators */
+struct of_bus {
+ const char *name;
+ const char *addresses;
+ int (*match)(struct device_node *parent);
+ void (*count_cells)(struct device_node *child,
+ int *addrc, int *sizec);
+ u64 (*map)(u32 *addr, u32 *range, int na, int ns, int pna);
+ int (*translate)(u32 *addr, u64 offset, int na);
+};
+
+
+/*
+ * Default translator (generic bus)
+ */
+
+static void of_default_count_cells(struct device_node *dev,
+ int *addrc, int *sizec)
+{
+ if (addrc)
+ *addrc = prom_n_addr_cells(dev);
+ if (sizec)
+ *sizec = prom_n_size_cells(dev);
+}
+
+static u64 of_default_map(u32 *addr, u32 *range, int na, int ns, int pna)
+{
+ u64 cp, s, da;
+
+ cp = of_read_addr(range, na);
+ s = of_read_addr(range + na + pna, ns);
+ da = of_read_addr(addr, na);
+
+ DBG("OF: default map, cp="PRu64", s="PRu64", da="PRu64"\n",
+ cp, s, da);
+
+ if (da < cp || da >= (cp + s))
+ return OF_BAD_ADDR;
+ return da - cp;
+}
+
+static int of_default_translate(u32 *addr, u64 offset, int na)
+{
+ u64 a = of_read_addr(addr, na);
+ memset(addr, 0, na * 4);
+ a += offset;
+ if (na > 1)
+ addr[na - 2] = a >> 32;
+ addr[na - 1] = a & 0xffffffffu;
+
+ return 0;
+}
+
+
+/*
+ * PCI bus specific translator
+ */
+
+static int of_bus_pci_match(struct device_node *np)
+{
+ return !strcmp(np->type, "pci");
+}
+
+static void of_bus_pci_count_cells(struct device_node *np,
+ int *addrc, int *sizec)
+{
+ if (addrc)
+ *addrc = 3;
+ if (sizec)
+ *sizec = 2;
+}
+
+static u64 of_bus_pci_map(u32 *addr, u32 *range, int na, int ns, int pna)
+{
+ u64 cp, s, da;
+
+ /* Check address type match */
+ if ((addr[0] ^ range[0]) & 0x03000000)
+ return OF_BAD_ADDR;
+
+ /* Read address values, skipping high cell */
+ cp = of_read_addr(range + 1, na - 1);
+ s = of_read_addr(range + na + pna, ns);
+ da = of_read_addr(addr + 1, na - 1);
+
+ DBG("OF: PCI map, cp="PRu64", s="PRu64", da="PRu64"\n", cp, s, da);
+
+ if (da < cp || da >= (cp + s))
+ return OF_BAD_ADDR;
+ return da - cp;
+}
+
+static int of_bus_pci_translate(u32 *addr, u64 offset, int na)
+{
+ return of_default_translate(addr + 1, offset, na - 1);
+}
+
+/*
+ * ISA bus specific translator
+ */
+
+static int of_bus_isa_match(struct device_node *np)
+{
+ return !strcmp(np->name, "isa");
+}
+
+static void of_bus_isa_count_cells(struct device_node *child,
+ int *addrc, int *sizec)
+{
+ if (addrc)
+ *addrc = 2;
+ if (sizec)
+ *sizec = 1;
+}
+
+static u64 of_bus_isa_map(u32 *addr, u32 *range, int na, int ns, int pna)
+{
+ u64 cp, s, da;
+
+ /* Check address type match */
+ if ((addr[0] ^ range[0]) & 0x00000001)
+ return OF_BAD_ADDR;
+
+ /* Read address values, skipping high cell */
+ cp = of_read_addr(range + 1, na - 1);
+ s = of_read_addr(range + na + pna, ns);
+ da = of_read_addr(addr + 1, na - 1);
+
+ DBG("OF: ISA map, cp="PRu64", s="PRu64", da="PRu64"\n", cp, s, da);
+
+ if (da < cp || da >= (cp + s))
+ return OF_BAD_ADDR;
+ return da - cp;
+}
+
+static int of_bus_isa_translate(u32 *addr, u64 offset, int na)
+{
+ return of_default_translate(addr + 1, offset, na - 1);
+}
+
+/*
+ * Array of bus specific translators
+ */
+
+static struct of_bus of_busses[] = {
+ /* PCI */
+ {
+ .name = "pci",
+ .addresses = "assigned-addresses",
+ .match = of_bus_pci_match,
+ .count_cells = of_bus_pci_count_cells,
+ .map = of_bus_pci_map,
+ .translate = of_bus_pci_translate,
+ },
+ /* ISA */
+ {
+ .name = "isa",
+ .addresses = "reg",
+ .match = of_bus_isa_match,
+ .count_cells = of_bus_isa_count_cells,
+ .map = of_bus_isa_map,
+ .translate = of_bus_isa_translate,
+ },
+ /* Default */
+ {
+ .name = "default",
+ .addresses = "reg",
+ .match = NULL,
+ .count_cells = of_default_count_cells,
+ .map = of_default_map,
+ .translate = of_default_translate,
+ },
+};
+
+static struct of_bus *of_match_bus(struct device_node *np)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(of_busses); i ++)
+ if (!of_busses[i].match || of_busses[i].match(np))
+ return &of_busses[i];
+ BUG();
+ return NULL;
+}
+
+static int of_translate_one(struct device_node *parent, struct of_bus *bus,
+ struct of_bus *pbus, u32 *addr,
+ int na, int ns, int pna)
+{
+ u32 *ranges;
+ unsigned int rlen;
+ int rone;
+ u64 offset = OF_BAD_ADDR;
+
+ /* Normally, an absence of a "ranges" property means we are
+ * crossing a non-translatable boundary, and thus the addresses
+ * below the current not cannot be converted to CPU physical ones.
+ * Unfortunately, while this is very clear in the spec, it's not
+ * what Apple understood, and they do have things like /uni-n or
+ * /ht nodes with no "ranges" property and a lot of perfectly
+ * useable mapped devices below them. Thus we treat the absence of
+ * "ranges" as equivalent to an empty "ranges" property which means
+ * a 1:1 translation at that level. It's up to the caller not to try
+ * to translate addresses that aren't supposed to be translated in
+ * the first place. --BenH.
+ */
+ ranges = (u32 *)get_property(parent, "ranges", &rlen);
+ if (ranges == NULL || rlen == 0) {
+ offset = of_read_addr(addr, na);
+ memset(addr, 0, pna);
+ goto finish;
+ }
+
+ DBG("OF: walking ranges...\n");
+
+ /* Now walk through the ranges */
+ rlen /= 4;
+ rone = na + pna + ns;
+ for (; rlen >= rone; rlen -= rone, ranges += rone) {
+ offset = bus->map(addr, ranges, na, ns, pna);
+ if (offset != OF_BAD_ADDR)
+ break;
+ }
+ if (offset == OF_BAD_ADDR) {
+ DBG("OF: not found !\n");
+ return 1;
+ }
+ memcpy(addr, ranges + na, 4 * pna);
+
+ finish:
+ of_dump_addr("OF: parent translation for:", addr, pna);
+ DBG("OF: with offset: %lx\n", offset);
+
+ /* Translate it into parent bus space */
+ return pbus->translate(addr, offset, pna);
+}
+
+
+/*
+ * Translate an address from the device-tree into a CPU physical address,
+ * this walks up the tree and applies the various bus mappings on the
+ * way.
+ *
+ * Note: We consider that crossing any level with #size-cells == 0 to mean
+ * that translation is impossible (that is we are not dealing with a value
+ * that can be mapped to a cpu physical address). This is not really specified
+ * that way, but this is traditionally the way IBM at least do things
+ */
+u64 of_translate_address(struct device_node *dev, u32 *in_addr)
+{
+ struct device_node *parent = NULL;
+ struct of_bus *bus, *pbus;
+ u32 addr[OF_MAX_ADDR_CELLS];
+ int na, ns, pna, pns;
+ u64 result = OF_BAD_ADDR;
+
+ DBG("OF: ** translation for device %s **\n", dev->full_name);
+
+ /* Increase refcount at current level */
+ of_node_get(dev);
+
+ /* Get parent & match bus type */
+ parent = of_get_parent(dev);
+ if (parent == NULL)
+ goto bail;
+ bus = of_match_bus(parent);
+
+ /* Cound address cells & copy address locally */
+ bus->count_cells(dev, &na, &ns);
+ if (!OF_CHECK_COUNTS(na, ns)) {
+ printk(KERN_ERR "prom_parse: Bad cell count for %s\n",
+ dev->full_name);
+ goto bail;
+ }
+ memcpy(addr, in_addr, na * 4);
+
+ DBG("OF: bus is %s (na=%d, ns=%d) on %s\n",
+ bus->name, na, ns, parent->full_name);
+ of_dump_addr("OF: translating address:", addr, na);
+
+ /* Translate */
+ for (;;) {
+ /* Switch to parent bus */
+ of_node_put(dev);
+ dev = parent;
+ parent = of_get_parent(dev);
+
+ /* If root, we have finished */
+ if (parent == NULL) {
+ DBG("OF: reached root node\n");
+ result = of_read_addr(addr, na);
+ break;
+ }
+
+ /* Get new parent bus and counts */
+ pbus = of_match_bus(parent);
+ pbus->count_cells(dev, &pna, &pns);
+ if (!OF_CHECK_COUNTS(pna, pns)) {
+ printk(KERN_ERR "prom_parse: Bad cell count for %s\n",
+ dev->full_name);
+ break;
+ }
+
+ DBG("OF: parent bus is %s (na=%d, ns=%d) on %s\n",
+ pbus->name, pna, pns, parent->full_name);
+
+ /* Apply bus translation */
+ if (of_translate_one(dev, bus, pbus, addr, na, ns, pna))
+ break;
+
+ /* Complete the move up one level */
+ na = pna;
+ ns = pns;
+ bus = pbus;
+
+ of_dump_addr("OF: one level translation:", addr, na);
+ }
+ bail:
+ of_node_put(parent);
+ of_node_put(dev);
+
+ return result;
+}
+EXPORT_SYMBOL(of_translate_address);
+
+u32 *of_get_address(struct device_node *dev, int index, u64 *size)
+{
+ u32 *prop;
+ unsigned int psize;
+ struct device_node *parent;
+ struct of_bus *bus;
+ int onesize, i, na, ns;
+
+ /* Get parent & match bus type */
+ parent = of_get_parent(dev);
+ if (parent == NULL)
+ return NULL;
+ bus = of_match_bus(parent);
+ bus->count_cells(dev, &na, &ns);
+ of_node_put(parent);
+ if (!OF_CHECK_COUNTS(na, ns))
+ return NULL;
+
+ /* Get "reg" or "assigned-addresses" property */
+ prop = (u32 *)get_property(dev, bus->addresses, &psize);
+ if (prop == NULL)
+ return NULL;
+ psize /= 4;
+
+ onesize = na + ns;
+ for (i = 0; psize >= onesize; psize -= onesize, prop += onesize, i++)
+ if (i == index) {
+ if (size)
+ *size = of_read_addr(prop + na, ns);
+ return prop;
+ }
+ return NULL;
+}
+EXPORT_SYMBOL(of_get_address);
+
+u32 *of_get_pci_address(struct device_node *dev, int bar_no, u64 *size)
+{
+ u32 *addr;
+ int index;
+
+ for (index = 0; (addr = of_get_address(dev, index, size)) != NULL;
+ index++) {
+ if ((addr[0] & 0xff) == ((bar_no * 4) + PCI_BASE_ADDRESS_0))
+ return addr;
+ }
+ return NULL;
+}
+EXPORT_SYMBOL(of_get_pci_address);
Index: linux-serialfix/include/asm-powerpc/mmu.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/mmu.h 2005-11-23 16:54:14.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/mmu.h 2005-11-23 16:54:24.000000000 +1100
@@ -393,6 +393,10 @@ static inline unsigned long get_vsid(uns
#define VSID_SCRAMBLE(pvsid) (((pvsid) * VSID_MULTIPLIER) % VSID_MODULUS)
#define KERNEL_VSID(ea) VSID_SCRAMBLE(GET_ESID(ea))
+/* Physical address used by some IO functions */
+typedef unsigned long phys_addr_t;
+
+
#endif /* __ASSEMBLY */
#endif /* CONFIG_PPC64 */
Index: linux-serialfix/include/asm-powerpc/prom.h
===================================================================
--- linux-serialfix.orig/include/asm-powerpc/prom.h 2005-11-23 16:54:14.000000000 +1100
+++ linux-serialfix/include/asm-powerpc/prom.h 2005-11-23 16:54:24.000000000 +1100
@@ -223,5 +223,14 @@ extern struct resource *request_OF_resou
int index, const char* name_postfix);
extern int release_OF_resource(struct device_node* node, int index);
+/*
+ * Address translation function(s)
+ */
+#define OF_BAD_ADDR ((u64)-1)
+extern u64 of_translate_address(struct device_node *np, u32 *addr);
+extern u32 *of_get_address(struct device_node *dev, int index, u64 *size);
+extern u32 *of_get_pci_address(struct device_node *dev, int bar_no, u64 *size);
+
+
#endif /* __KERNEL__ */
#endif /* _POWERPC_PROM_H */
Index: linux-serialfix/include/asm-ppc/prom.h
===================================================================
--- linux-serialfix.orig/include/asm-ppc/prom.h 2005-11-23 16:54:14.000000000 +1100
+++ linux-serialfix/include/asm-ppc/prom.h 2005-11-23 16:54:24.000000000 +1100
@@ -136,5 +136,15 @@ extern unsigned long sub_reloc_offset(un
#define PTRRELOC(x) ((typeof(x))add_reloc_offset((unsigned long)(x)))
#define PTRUNRELOC(x) ((typeof(x))sub_reloc_offset((unsigned long)(x)))
+
+/*
+ * Address translation function(s)
+ */
+#define OF_BAD_ADDR ((u64)-1)
+extern u64 of_translate_address(struct device_node *np, u32 *addr);
+extern u32 *of_get_address(struct device_node *dev, int index, u64 *size);
+extern u32 *of_get_pci_address(struct device_node *dev, int bar_no, u64 *size);
+
+
#endif /* _PPC_PROM_H */
#endif /* __KERNEL__ */
^ permalink raw reply
* Re: MPC8272 Fast Ethernet Controller drver
From: Kumar Gala @ 2005-11-23 6:48 UTC (permalink / raw)
To: alexv; +Cc: linuxppc-dev
In-Reply-To: <012201c5eead$7d8fdbe0$0676cb0a@asia.ad.flextronics.com>
You want the MPC8272 User Manual on the Freescale website.
Also, there are some code examples on the freescale site.
- kumar
On Nov 21, 2005, at 9:08 AM, alexv wrote:
>
>
> Hi,
> my new project uses a MPC8272. but i couldn't find any good
> tutorial or
> things like that describing the registers and all
> especially about CPM,FCC.. Presently I am doing my assembly language
> progamming using powerPC tutorial.
> Can any one help me.
>
> Thanks and Regards,
>
> Alex
>
>
>
>
> **********************************************************************
> *****
> This message is proprietary to Future Software Limited (FSL)
> and is intended solely for the use of the individual to whom it
> is addressed. It may contain privileged or confidential information
> and should not be circulated or used for any purpose other than for
> what it is intended.
>
> If you have received this message in error, please notify the
> originator immediately. If you are not the intended recipient,
> you are notified that you are strictly prohibited from using,
> copying, altering, or disclosing the contents of this message.
> FSL accepts no responsibility for loss or damage arising from
> the use of the information transmitted by this email including
> damage from virus.
> **********************************************************************
> *****
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
^ permalink raw reply
* Re: Linux on MPC8541 and MPC8560
From: Kumar Gala @ 2005-11-23 6:09 UTC (permalink / raw)
To: le tang; +Cc: linuxppc-embedded
In-Reply-To: <20051123053711.1110.qmail@web50607.mail.yahoo.com>
On Nov 22, 2005, at 11:37 PM, le tang wrote:
> Hi,
>
> I got questions on developing the linux on MPC8560 and
> MPC8541.
>
> 1) Which version of linux would be best suited for
> these two processors?
2.6.14 is a good starting point. Older 2.6 kernels have support for
MPC8540/MPC8560, I forget when we introduced it.
> 2) Can I make model these two processor accurately
> with device trees on the PSIM?
Extremely unlikely. While I think PSIM has some support for e500 I
dont think it handles anything close enough to boot linux.
> 3) I have cross compiled gcc with target as
> powerpc-eabi option, and I am using
> powerpc-eabi-objdump to disassemble a pre-compiled
> code, I have tried use -M e500 options, but not sure
> if that would give a very accurate assemly listing.
It should be. The kernel is build with -me500 being passed to the
assembler. for the majority of code it doesn't matter. it will
mainly get proper decode of m{t,f}spr instructions and a few other
things.
- kumar
^ permalink raw reply
* Linux on MPC8541 and MPC8560
From: le tang @ 2005-11-23 5:37 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <200511222141.18861.pantelis@embeddedalley.com>
Hi,
I got questions on developing the linux on MPC8560 and
MPC8541.
1) Which version of linux would be best suited for
these two processors?
2) Can I make model these two processor accurately
with device trees on the PSIM?
3) I have cross compiled gcc with target as
powerpc-eabi option, and I am using
powerpc-eabi-objdump to disassemble a pre-compiled
code, I have tried use -M e500 options, but not sure
if that would give a very accurate assemly listing.
Okay, Thanks for your advice,
Le
__________________________________
Yahoo! FareChase: Search multiple travel sites in one click.
http://farechase.yahoo.com
^ permalink raw reply
* Re: [PATCH] Fix USB suspend/resume crasher
From: Benjamin Herrenschmidt @ 2005-11-23 5:13 UTC (permalink / raw)
To: ncunningham
Cc: Andrew Morton, Greg KH, Linux Kernel Mailing List, David Brownell,
linuxppc-dev list, Alan Stern
In-Reply-To: <1132715647.4707.8.camel@localhost>
> Sounds great. Maybe I'll finally be able to change my first question to
> people with suspend problems from: "Do you have USB built as modules and
> unloaded while suspending."
Heh, I don't know :) I haven't done anything to UHCI at this point, and
there are still other possible issues.
For example, we should probably do the "handoff" trick on resume as well
as on boot. In fact, I suspect that most PCI quirks should be re-run on
resume, with IRQs off if possible, so that stuffs can be put back into
some sane state when coming back from the BIOS before they get a chance
to spam the kernel with bogus IRQs left enabled by that same BIOS (does
this happen ?) or other niceties of that sort... I don't have any of
these problems on powermacs, but x86 might not be yet at the end of the
tunnel...
Ben.
^ permalink raw reply
* Re: [PATCH] Fix USB suspend/resume crasher
From: Nigel Cunningham @ 2005-11-23 3:14 UTC (permalink / raw)
To: Benjamin Herrenschmidt
Cc: Andrew Morton, Greg KH, Linux Kernel Mailing List, David Brownell,
linuxppc-dev list, Alan Stern
In-Reply-To: <1132715288.26560.262.camel@gaston>
Hi.
On Wed, 2005-11-23 at 14:08, Benjamin Herrenschmidt wrote:
> This is my latest patch against current linus -git, it closes the IRQ
> race and makes various other OHCI & EHCI code path safer vs.
> suspend/resume. I've been able to (finally !) successfully suspend and
> resume various Mac models, with or without USB mouse plugged, or
> plugging while asleep, or unplugging while asleep etc... all without a
> crash. There are still some races here or there in the USB code, but at
> least the main cause of crash is now fixes by this patch (access to a
> controller that has been suspended, due to either shared interrupts or
> other code path).
>
> I haven't fixed UHCI as I don't have any HW to test, though I hope I
> haven't broken it neither. Alan, I would appreciate if you could have a
> look.
>
> This patch applies on top of the patch that moves the PowerMac specific
> code out of ohci-pci.c to hcd-pci.c where it belongs. This patch isn't
> upstream yet for reasons I don't fully understand (why does USB stuffs
> has such a high latency for going upstream ?), I'm sending it as a reply
> to this email for completeness.
>
> Without this patch, you cannot reliably sleep/wakeup any recent Mac, and
> I suspect PCs have some more sneaky issues too (they don't frankly crash
> with machine checks because x86 tend to silently swallow PCI errors but
> that won't last afaik, at least PCI Express will blow up in those
> situations, but the USB code may still misbehave).
Sounds great. Maybe I'll finally be able to change my first question to
people with suspend problems from: "Do you have USB built as modules and
unloaded while suspending."
Regards,
Nigel
^ permalink raw reply
* Re: [PATCH] Fix USB suspend/resume crasher
From: Benjamin Herrenschmidt @ 2005-11-23 3:09 UTC (permalink / raw)
To: David Brownell
Cc: Andrew Morton, Greg KH, Linux Kernel list, linuxppc-dev list,
Alan Stern
In-Reply-To: <1132715288.26560.262.camel@gaston>
> This patch applies on top of the patch that moves the PowerMac specific
> code out of ohci-pci.c to hcd-pci.c where it belongs. This patch isn't
> upstream yet for reasons I don't fully understand (why does USB stuffs
> has such a high latency for going upstream ?), I'm sending it as a reply
> to this email for completeness.
Here it is. it's my understand that it's already been queued somewhere
for submission by David for some time though.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Index: linux-serialfix/drivers/usb/core/hcd-pci.c
===================================================================
--- linux-serialfix.orig/drivers/usb/core/hcd-pci.c 2005-11-21 11:53:15.000000000 +1100
+++ linux-serialfix/drivers/usb/core/hcd-pci.c 2005-11-23 11:23:24.000000000 +1100
@@ -27,6 +27,13 @@
#include "usb.h"
#include "hcd.h"
+#ifdef CONFIG_PPC_PMAC
+#include <asm/machdep.h>
+#include <asm/pmac_feature.h>
+#include <asm/pci-bridge.h>
+#include <asm/prom.h>
+#endif
+
/* PCI-based HCs are common, but plenty of non-PCI HCs are used too */
@@ -277,6 +284,16 @@
}
done:
+#ifdef CONFIG_PPC_PMAC
+ if (retval == 0 && _machine == _MACH_Pmac) {
+ struct device_node *of_node;
+
+ /* Disable USB PAD & cell clock */
+ of_node = pci_device_to_OF_node(dev);
+ if (of_node)
+ pmac_call_feature(PMAC_FTR_USB_ENABLE, of_node, 0, 0);
+ }
+#endif /* CONFIG_PPC_PMAC */
if (retval == 0)
dev->dev.power.power_state = PMSG_SUSPEND;
return retval;
@@ -301,6 +318,17 @@
return 0;
}
+#ifdef CONFIG_PPC_PMAC
+ if (_machine == _MACH_Pmac) {
+ struct device_node *of_node;
+
+ /* Re-enable USB PAD & cell clock */
+ of_node = pci_device_to_OF_node(dev);
+ if (of_node)
+ pmac_call_feature(PMAC_FTR_USB_ENABLE, of_node, 0, 1);
+ }
+#endif /* CONFIG_PPC_PMAC */
+
/* NOTE: chip docs cover clean "real suspend" cases (what Linux
* calls "standby", "suspend to RAM", and so on). There are also
* dirty cases when swsusp fakes a suspend in "shutdown" mode.
Index: linux-serialfix/drivers/usb/host/ohci-pci.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ohci-pci.c 2005-11-14 10:42:00.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ohci-pci.c 2005-11-23 11:25:26.000000000 +1100
@@ -114,40 +114,12 @@
static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
{
- /* root hub was already suspended */
-
- /* FIXME these PMAC things get called in the wrong places. ASIC
- * clocks should be turned off AFTER entering D3, and on BEFORE
- * trying to enter D0. Evidently the PCI layer doesn't currently
- * provide the right sort of platform hooks for this ...
- */
-#ifdef CONFIG_PPC_PMAC
- if (_machine == _MACH_Pmac) {
- struct device_node *of_node;
-
- /* Disable USB PAD & cell clock */
- of_node = pci_device_to_OF_node (to_pci_dev(hcd->self.controller));
- if (of_node)
- pmac_call_feature(PMAC_FTR_USB_ENABLE, of_node, 0, 0);
- }
-#endif /* CONFIG_PPC_PMAC */
return 0;
}
static int ohci_pci_resume (struct usb_hcd *hcd)
{
-#ifdef CONFIG_PPC_PMAC
- if (_machine == _MACH_Pmac) {
- struct device_node *of_node;
-
- /* Re-enable USB PAD & cell clock */
- of_node = pci_device_to_OF_node (to_pci_dev(hcd->self.controller));
- if (of_node)
- pmac_call_feature (PMAC_FTR_USB_ENABLE, of_node, 0, 1);
- }
-#endif /* CONFIG_PPC_PMAC */
-
usb_hcd_resume_root_hub(hcd);
return 0;
}
^ permalink raw reply
* [PATCH] Fix USB suspend/resume crasher
From: Benjamin Herrenschmidt @ 2005-11-23 3:08 UTC (permalink / raw)
To: David Brownell
Cc: Andrew Morton, Greg KH, Linux Kernel list, linuxppc-dev list,
Alan Stern
This is my latest patch against current linus -git, it closes the IRQ
race and makes various other OHCI & EHCI code path safer vs.
suspend/resume. I've been able to (finally !) successfully suspend and
resume various Mac models, with or without USB mouse plugged, or
plugging while asleep, or unplugging while asleep etc... all without a
crash. There are still some races here or there in the USB code, but at
least the main cause of crash is now fixes by this patch (access to a
controller that has been suspended, due to either shared interrupts or
other code path).
I haven't fixed UHCI as I don't have any HW to test, though I hope I
haven't broken it neither. Alan, I would appreciate if you could have a
look.
This patch applies on top of the patch that moves the PowerMac specific
code out of ohci-pci.c to hcd-pci.c where it belongs. This patch isn't
upstream yet for reasons I don't fully understand (why does USB stuffs
has such a high latency for going upstream ?), I'm sending it as a reply
to this email for completeness.
Without this patch, you cannot reliably sleep/wakeup any recent Mac, and
I suspect PCs have some more sneaky issues too (they don't frankly crash
with machine checks because x86 tend to silently swallow PCI errors but
that won't last afaik, at least PCI Express will blow up in those
situations, but the USB code may still misbehave).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Note that I REALLY want that in 2.6.15. 2.6.14 is already broken, though I
have a similar patch for it that some users have been successfully testing
and I don't want 2.6.15 to be broken too. So unless you have a major issue
with the patch as it is and it breaks something, I think it should be applied,
and I don't want to get into yet another 10000 email exchange discussion on
the merit of doing proper locking and why the current situation is broken...
Index: linux-serialfix/drivers/usb/core/hcd-pci.c
===================================================================
--- linux-serialfix.orig/drivers/usb/core/hcd-pci.c 2005-11-23 13:52:23.000000000 +1100
+++ linux-serialfix/drivers/usb/core/hcd-pci.c 2005-11-23 13:52:32.000000000 +1100
@@ -218,6 +218,7 @@
goto done;
}
}
+ synchronize_irq(dev->irq);
/* FIXME until the generic PM interfaces change a lot more, this
* can't use PCI D1 and D2 states. For example, the confusion
@@ -386,7 +387,7 @@
dev->dev.power.power_state = PMSG_ON;
- hcd->saw_irq = 0;
+ clear_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
if (hcd->driver->resume) {
retval = hcd->driver->resume(hcd);
Index: linux-serialfix/drivers/usb/core/hcd.c
===================================================================
--- linux-serialfix.orig/drivers/usb/core/hcd.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/core/hcd.c 2005-11-23 13:52:32.000000000 +1100
@@ -1315,11 +1315,12 @@
* finish unlinking the initial failed usb_set_address()
* or device descriptor fetch.
*/
- if (!hcd->saw_irq && hcd->self.root_hub != urb->dev) {
+ if (!test_bit(HCD_FLAG_SAW_IRQ, &hcd->flags)
+ && hcd->self.root_hub != urb->dev) {
dev_warn (hcd->self.controller, "Unlink after no-IRQ? "
"Controller is probably using the wrong IRQ."
"\n");
- hcd->saw_irq = 1;
+ set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
}
urb->status = status;
@@ -1649,13 +1650,15 @@
struct usb_hcd *hcd = __hcd;
int start = hcd->state;
- if (start == HC_STATE_HALT)
+ if (unlikely(start == HC_STATE_HALT ||
+ !test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
return IRQ_NONE;
if (hcd->driver->irq (hcd, r) == IRQ_NONE)
return IRQ_NONE;
- hcd->saw_irq = 1;
- if (hcd->state == HC_STATE_HALT)
+ set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
+
+ if (unlikely(hcd->state == HC_STATE_HALT))
usb_hc_died (hcd);
return IRQ_HANDLED;
}
@@ -1768,6 +1771,8 @@
dev_info(hcd->self.controller, "%s\n", hcd->product_desc);
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+
/* till now HC has been in an indeterminate state ... */
if (hcd->driver->reset && (retval = hcd->driver->reset(hcd)) < 0) {
dev_err(hcd->self.controller, "can't reset\n");
Index: linux-serialfix/drivers/usb/core/hcd.h
===================================================================
--- linux-serialfix.orig/drivers/usb/core/hcd.h 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/core/hcd.h 2005-11-23 13:52:32.000000000 +1100
@@ -72,7 +72,12 @@
* hardware info/state
*/
const struct hc_driver *driver; /* hw-specific hooks */
- unsigned saw_irq : 1;
+
+ /* Flags that need to be manipulated atomically */
+ unsigned long flags;
+#define HCD_FLAG_HW_ACCESSIBLE 0x00000001
+#define HCD_FLAG_SAW_IRQ 0x00000002
+
unsigned can_wakeup:1; /* hw supports wakeup? */
unsigned remote_wakeup:1;/* sw should use wakeup? */
unsigned rh_registered:1;/* is root hub registered? */
Index: linux-serialfix/drivers/usb/host/ehci-pci.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ehci-pci.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ehci-pci.c 2005-11-23 13:52:32.000000000 +1100
@@ -244,22 +244,34 @@
static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
+ unsigned long flags;
+ int rc = 0;
if (time_before (jiffies, ehci->next_statechange))
msleep (100);
-#ifdef CONFIG_USB_SUSPEND
- (void) usb_suspend_device (hcd->self.root_hub);
-#else
- usb_lock_device (hcd->self.root_hub);
- (void) ehci_bus_suspend (hcd);
- usb_unlock_device (hcd->self.root_hub);
-#endif
+ /* Root hub was already suspended. Disable irq emission and
+ * mark HW unaccessible, bail out if RH has been resumed. Use
+ * the spinlock to properly synchronize with possible pending
+ * RH suspend or resume activity.
+ *
+ * This is still racy as hcd->state is manipulated outside of
+ * any locks =P But that will be a different fix.
+ */
+ spin_lock_irqsave (&ehci->lock, flags);
+ if (hcd->state != HC_STATE_SUSPENDED) {
+ rc = -EINVAL;
+ goto bail;
+ }
+ writel (0, &ehci->regs->intr_enable);
+ clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+ bail:
+ spin_unlock_irqrestore (&ehci->lock, flags);
// save (PCI) FLADJ in case of Vaux power loss
// ... we'd only use it to handle clock skew
- return 0;
+ return rc;
}
static int ehci_pci_resume (struct usb_hcd *hcd)
@@ -274,6 +286,8 @@
if (time_before (jiffies, ehci->next_statechange))
msleep (100);
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+
/* If any port is suspended (or owned by the companion),
* we know we can/must resume the HC (and mustn't reset it).
*/
Index: linux-serialfix/drivers/usb/host/ehci-q.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ehci-q.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ehci-q.c 2005-11-23 13:52:32.000000000 +1100
@@ -912,6 +912,7 @@
int epnum;
unsigned long flags;
struct ehci_qh *qh = NULL;
+ int rc = 0;
qtd = list_entry (qtd_list->next, struct ehci_qtd, qtd_list);
epnum = ep->desc.bEndpointAddress;
@@ -926,21 +927,28 @@
#endif
spin_lock_irqsave (&ehci->lock, flags);
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE,
+ &ehci_to_hcd(ehci)->flags))) {
+ rc = -ESHUTDOWN;
+ goto done;
+ }
+
qh = qh_append_tds (ehci, urb, qtd_list, epnum, &ep->hcpriv);
+ if (unlikely(qh == NULL)) {
+ rc = -ENOMEM;
+ goto done;
+ }
/* Control/bulk operations through TTs don't need scheduling,
* the HC and TT handle it when the TT has a buffer ready.
*/
- if (likely (qh != NULL)) {
- if (likely (qh->qh_state == QH_STATE_IDLE))
- qh_link_async (ehci, qh_get (qh));
- }
+ if (likely (qh->qh_state == QH_STATE_IDLE))
+ qh_link_async (ehci, qh_get (qh));
+ done:
spin_unlock_irqrestore (&ehci->lock, flags);
- if (unlikely (qh == NULL)) {
+ if (unlikely (qh == NULL))
qtd_list_free (ehci, urb, qtd_list);
- return -ENOMEM;
- }
- return 0;
+ return rc;
}
/*-------------------------------------------------------------------------*/
Index: linux-serialfix/drivers/usb/host/ehci-sched.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ehci-sched.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ehci-sched.c 2005-11-23 13:52:32.000000000 +1100
@@ -602,6 +602,12 @@
spin_lock_irqsave (&ehci->lock, flags);
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE,
+ &ehci_to_hcd(ehci)->flags))) {
+ status = -ESHUTDOWN;
+ goto done;
+ }
+
/* get qh and force any scheduling errors */
INIT_LIST_HEAD (&empty);
qh = qh_append_tds (ehci, urb, &empty, epnum, &ep->hcpriv);
@@ -1456,7 +1462,11 @@
/* schedule ... need to lock */
spin_lock_irqsave (&ehci->lock, flags);
- status = iso_stream_schedule (ehci, urb, stream);
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE,
+ &ehci_to_hcd(ehci)->flags)))
+ status = -ESHUTDOWN;
+ else
+ status = iso_stream_schedule (ehci, urb, stream);
if (likely (status == 0))
itd_link_urb (ehci, urb, ehci->periodic_size << 3, stream);
spin_unlock_irqrestore (&ehci->lock, flags);
@@ -1815,7 +1825,11 @@
/* schedule ... need to lock */
spin_lock_irqsave (&ehci->lock, flags);
- status = iso_stream_schedule (ehci, urb, stream);
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE,
+ &ehci_to_hcd(ehci)->flags)))
+ status = -ESHUTDOWN;
+ else
+ status = iso_stream_schedule (ehci, urb, stream);
if (status == 0)
sitd_link_urb (ehci, urb, ehci->periodic_size << 3, stream);
spin_unlock_irqrestore (&ehci->lock, flags);
Index: linux-serialfix/drivers/usb/host/ohci-hcd.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ohci-hcd.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ohci-hcd.c 2005-11-23 13:57:06.000000000 +1100
@@ -115,7 +115,7 @@
/*-------------------------------------------------------------------------*/
-// #define OHCI_VERBOSE_DEBUG /* not always helpful */
+#undef OHCI_VERBOSE_DEBUG /* not always helpful */
/* For initializing controller (mask in an HCFS mode too) */
#define OHCI_CONTROL_INIT OHCI_CTRL_CBSR
@@ -253,6 +253,10 @@
spin_lock_irqsave (&ohci->lock, flags);
/* don't submit to a dead HC */
+ if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
+ retval = -ENODEV;
+ goto fail;
+ }
if (!HC_IS_RUNNING(hcd->state)) {
retval = -ENODEV;
goto fail;
Index: linux-serialfix/drivers/usb/host/ohci-hub.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ohci-hub.c 2005-11-23 13:47:45.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ohci-hub.c 2005-11-23 13:54:04.000000000 +1100
@@ -53,6 +53,11 @@
spin_lock_irqsave (&ohci->lock, flags);
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) {
+ spin_unlock_irqrestore (&ohci->lock, flags);
+ return -ESHUTDOWN;
+ }
+
ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_RESUME:
@@ -140,11 +145,19 @@
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
u32 temp, enables;
int status = -EINPROGRESS;
+ unsigned long flags;
if (time_before (jiffies, ohci->next_statechange))
msleep(5);
- spin_lock_irq (&ohci->lock);
+ spin_lock_irqsave (&ohci->lock, flags);
+
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) {
+ spin_unlock_irqrestore (&ohci->lock, flags);
+ return -ESHUTDOWN;
+ }
+
+
ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
@@ -179,7 +192,7 @@
ohci_dbg (ohci, "lost power\n");
status = -EBUSY;
}
- spin_unlock_irq (&ohci->lock);
+ spin_unlock_irqrestore (&ohci->lock, flags);
if (status == -EBUSY) {
(void) ohci_init (ohci);
return ohci_restart (ohci);
@@ -297,8 +310,8 @@
/* handle autosuspended root: finish resuming before
* letting khubd or root hub timer see state changes.
*/
- if ((ohci->hc_control & OHCI_CTRL_HCFS) != OHCI_USB_OPER
- || !HC_IS_RUNNING(hcd->state)) {
+ if (unlikely((ohci->hc_control & OHCI_CTRL_HCFS) != OHCI_USB_OPER
+ || !HC_IS_RUNNING(hcd->state))) {
can_suspend = 0;
goto done;
}
@@ -508,6 +521,9 @@
u32 temp;
int retval = 0;
+ if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)))
+ return -ESHUTDOWN;
+
switch (typeReq) {
case ClearHubFeature:
switch (wValue) {
Index: linux-serialfix/drivers/usb/host/ohci-pci.c
===================================================================
--- linux-serialfix.orig/drivers/usb/host/ohci-pci.c 2005-11-23 13:52:23.000000000 +1100
+++ linux-serialfix/drivers/usb/host/ohci-pci.c 2005-11-23 13:52:32.000000000 +1100
@@ -114,12 +114,35 @@
static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
{
- return 0;
+ struct ohci_hcd *ohci = hcd_to_ohci (hcd);
+ unsigned long flags;
+ int rc = 0;
+
+ /* Root hub was already suspended. Disable irq emission and
+ * mark HW unaccessible, bail out if RH has been resumed. Use
+ * the spinlock to properly synchronize with possible pending
+ * RH suspend or resume activity.
+ *
+ * This is still racy as hcd->state is manipulated outside of
+ * any locks =P But that will be a different fix.
+ */
+ spin_lock_irqsave (&ohci->lock, flags);
+ if (hcd->state != HC_STATE_SUSPENDED) {
+ rc = -EINVAL;
+ goto bail;
+ }
+ ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
+ clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+ bail:
+ spin_unlock_irqrestore (&ohci->lock, flags);
+
+ return rc;
}
static int ohci_pci_resume (struct usb_hcd *hcd)
{
+ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
usb_hcd_resume_root_hub(hcd);
return 0;
}
^ permalink raw reply
* Re: [PATCH] ppc32: 8xx board-specific platform stuff for fs_enet
From: Paul Mackerras @ 2005-11-23 2:40 UTC (permalink / raw)
To: Marcelo Tosatti; +Cc: linuxppc-embedded list
In-Reply-To: <20051118090845.GB12765@logos.cnet>
Marcelo Tosatti writes:
> Paul, you're OK with the following definitions on asm-ppc/io.h?
>
> +/* access ports */
> +#define setbits32(_addr, _v) out_be32(&(_addr), in_be32(&(_addr)) | (_v))
> +#define clrbits32(_addr, _v) out_be32(&(_addr), in_be32(&(_addr)) & ~(_v))
> +
> +#define setbits16(_addr, _v) out_be16(&(_addr), in_be16(&(_addr)) | (_v))
> +#define clrbits16(_addr, _v) out_be16(&(_addr), in_be16(&(_addr)) & ~(_v))
I guess so... how many drivers need these things?
Paul.
^ permalink raw reply
* Re: Trying to understand initsenses and pci_irq_table
From: Richard Danter @ 2005-11-22 19:43 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <4382F0F2.4040807@ntlworld.com>
Richard Danter wrote:
>
> The kernel crashes after starting init. I see some random characters on
> the serial and then nothing. Looking in the log buffer via JTAG I can
> see that the init process exited with signal 11. I assume this is
> unrelated to the above, but any suggestions where I should look?
I managed to fix this problem, so I am now booted and running busybox
from NFS :)
I'd still like a pointer to any docs explaining the PCI and interrupt
stuff if possible.
Thanks!
Rich
^ permalink raw reply
* Re: linux 2.6.9 on 8xx platform
From: Pantelis Antoniou @ 2005-11-22 19:41 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <000a01c5ef91$30772c20$5201a8c0@GEG2400>
On Tuesday 22 November 2005 20:18, Laurent Lagrange wrote:
>
> Hello all,
>
[snip]
>
>
Please try a recent kernel. 2.6.9 is known not to work on 8xx.
Pantelis
^ permalink raw reply
* linux 2.6.9 on 8xx platform
From: Laurent Lagrange @ 2005-11-22 18:18 UTC (permalink / raw)
To: linuxppc-embedded
Hello all,
I try to port a linux 2.6.9 from elinos free tool box on a 852T custom board
with a ramdisk filesystem.
I have already run a linux 2.4.18 on it without any problem.
When I have configured my 2.6 kernel, I found some new parameters in
advanced
setup menu.
For example, I don't understand what mean CONFIG_CONSISTENT_START/SIZE
and CONFIG_PIN_TLB values.
When I use the default value for CONFIG_CONSISTENT_START=0xff100000, the
kernel crashes in dma_alloc_init function in arch/ppc/kernel/dma-mapping.c.
I have made a search and seen that someone uses CONFIG_CONSISTENT_START
with 0xa0000000 for another 8xx board.
I tried it and pass the dma_alloc_init
but another problem occurs when the kernel tries to launch the init process.
Is there anyone who has already seen this problem?
Thanks
Laurent
..............
#
# Advanced setup
#
CONFIG_ADVANCED_OPTIONS=y
CONFIG_HIGHMEM_START=0xfe000000
# CONFIG_LOWMEM_SIZE_BOOL is not set
CONFIG_LOWMEM_SIZE=0x30000000
# CONFIG_KERNEL_START_BOOL is not set
CONFIG_KERNEL_START=0xc0000000
# CONFIG_TASK_SIZE_BOOL is not set
CONFIG_TASK_SIZE=0x80000000
CONFIG_CONSISTENT_START_BOOL=y
CONFIG_CONSISTENT_START=0xa0000000
# CONFIG_CONSISTENT_SIZE_BOOL is not set
CONFIG_CONSISTENT_SIZE=0x00200000
# CONFIG_BOOT_LOAD_BOOL is not set
CONFIG_BOOT_LOAD=0x00400000
# CONFIG_PIN_TLB is not set
loaded at: 00400000 0059A150
board data at: 00598114 00598150
relocated to: 00405114 00405150
zimage at: 00405A10 004E6F7F
initrd at: 004E7000 00597805
avail ram: 0059B000 02000000
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
Linux version 2.6.9-elinos-144 (852board@Linux1701) (version gcc 3.2.3
(ELinOS V3.1 3.2.3-35 2005-06-01)) #2 Tue Nov 22 17:25:58 CET 2005
Built 1 zonelists
Kernel command line: devfs=mount rootfstype=tmpfs root=/dev/ram rw
PID hash table entries: 256 (order: 8, 4096 bytes)
Decrementer Frequency = 187500000/60
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29504k available (1536k kernel code, 532k data, 68k init, 0k
highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
NET: Registered protocol family 16
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
Serial: CPM driver $Revision: 0.01 $
ttyCPM0 at MMIO 0xff000a80 (irq = 20) is a CPM UART
Using deadline io scheduler
physmap flash device: 2000000 at f8000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
6 cmdlinepart partitions found on MTD device phys_mapped_flash
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (tmpfs filesystem).
UNTAR: Extracting root archive: done.
Mounted devfs on /dev
Freeing unused kernel memory: 68k in
try init
Oops: kernel access of bad area, sig: 11 [#1]
NIP: C0008F18 LR: C000E78C SP: C04CBE00 REGS: c04cbd50 TRAP: 0300 Not
tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 30013C60, DSISR: C2000000
TASK = c04c4ba0[1] 'init' THREAD: c04ca000Last syscall: 45
GPR00: C01F4CA0 C04CBE00 C04C4BA0 30013000 00000100 000003C2 30013000
C04CBE28
GPR08: C01F0000 C01F4CA0 00000000 00007840 20000002 000637B0 00000001
FF000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 30013000
C01F4CA0
GPR24: 00000000 00000000 C01F3300 00000000 30013C60 003C2889 C022D840
C022D840
NIP [c0008f18] __flush_dcache_icache+0x14/0x40
LR [c000e78c] update_mmu_cache+0x94/0x98
Call trace:
[c003f0d4] do_no_page+0x1a4/0x364
[c003f450] handle_mm_fault+0xf8/0x178
[c000dd3c] do_page_fault+0x1d4/0x398
[c0006768] handle_page_fault+0xc/0x80
Kernel panic - not syncing: Attempted to kill init!
<0>Rebooting in 180 seconds..
^ permalink raw reply
* [PATCH] ppc32: Add P3P440 (440GP) board support
From: Stefan Roese @ 2005-11-22 17:34 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <200509161306.17103.sr@denx.de>
[-- Attachment #1: Type: text/plain, Size: 381 bytes --]
This patch adds support for the Prodrive P3P440 (440GP) PMC module.
Please note, that in arch/ppc/syslib/Makefile "todc_time" was generated
on all 4xx platforms. This is a problem with the P3P440, since it uses
a different RTC. I removed this 4xx - todc_time dependency and added it
to those boards really using it.
Signed-off-by: Stefan Roese <sr@denx.de>
Best regards,
Stefan
[-- Attachment #2: add-p3p440-board-support.patch --]
[-- Type: text/x-diff, Size: 42611 bytes --]
[PATCH] ppc32: Add P3P440 (440GP) board support
This patch adds support for the Prodrive P3P440 (440GP) PMC module.
Please note, that in arch/ppc/syslib/Makefile "todc_time" was generated
on all 4xx platforms. This is a problem with the P3P440, since it uses
a different RTC. I removed this 4xx - todc_time dependency and added it
to those boards really using it.
Signed-off-by: Stefan Roese <sr@denx.de>
---
commit 2537b8507f952c4635c0108bed06f3aade110a43
tree cd84ab91112624e13e800acafea9bca9b1ecaa4d
parent 989e4d6cbc69191c41ddf4b1c492457410376b43
author Stefan Roese <sr@denx.de> Tue, 22 Nov 2005 18:29:05 +0100
committer Stefan Roese <sr@denx.de> Tue, 22 Nov 2005 18:29:05 +0100
arch/ppc/configs/p3p440_defconfig | 1155 +++++++++++++++++++++++++++++++++++++
arch/ppc/platforms/4xx/Kconfig | 10
arch/ppc/platforms/4xx/Makefile | 1
arch/ppc/platforms/4xx/ibm440gp.h | 5
arch/ppc/platforms/4xx/p3p440.c | 362 ++++++++++++
arch/ppc/platforms/4xx/p3p440.h | 72 ++
arch/ppc/syslib/Makefile | 7
include/asm-ppc/ibm4xx.h | 4
8 files changed, 1613 insertions(+), 3 deletions(-)
diff --git a/arch/ppc/configs/p3p440_defconfig b/arch/ppc/configs/p3p440_defconfig
new file mode 100644
index 0000000..4477fff
--- /dev/null
+++ b/arch/ppc/configs/p3p440_defconfig
@@ -0,0 +1,1155 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.14
+# Tue Nov 22 10:21:06 2005
+#
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_PPC=y
+CONFIG_PPC32=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_SYSCTL=y
+# CONFIG_AUDIT is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
+# CONFIG_IKCONFIG is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_EMBEDDED=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+# CONFIG_MODULE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_LBD=y
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Processor
+#
+# CONFIG_6xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_POWER3 is not set
+# CONFIG_POWER4 is not set
+# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+# CONFIG_E500 is not set
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+# CONFIG_MATH_EMULATION is not set
+# CONFIG_KEXEC is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_4xx=y
+CONFIG_WANT_EARLY_SERIAL=y
+
+#
+# IBM 4xx options
+#
+# CONFIG_BAMBOO is not set
+# CONFIG_EBONY is not set
+# CONFIG_LUAN is not set
+# CONFIG_YUCCA is not set
+# CONFIG_OCOTEA is not set
+CONFIG_P3P440=y
+# CONFIG_YELLOWSTONE is not set
+# CONFIG_YOSEMITE is not set
+CONFIG_440GP=y
+CONFIG_440=y
+CONFIG_IBM_OCP=y
+# CONFIG_PPC4xx_DMA is not set
+CONFIG_PPC_GEN550=y
+CONFIG_NOT_COHERENT_CACHE=y
+
+#
+# Platform options
+#
+# CONFIG_PC_KEYBOARD is not set
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="ip=on"
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+# CONFIG_PPC_I8259 is not set
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCI_LEGACY_PROC is not set
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_BIC=y
+
+#
+# IP: Virtual Server Configuration
+#
+# CONFIG_IP_VS is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+# CONFIG_NETFILTER_NETLINK is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_IP_NF_CONNTRACK is not set
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_NET_DIVERT is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+# CONFIG_STANDALONE is not set
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_P3P440=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+
+#
+# NAND Flash Device Drivers
+#
+# CONFIG_MTD_NAND is not set
+
+#
+# OneNAND Flash Device Drivers
+#
+# CONFIG_MTD_ONENAND is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=y
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=y
+CONFIG_CHR_DEV_SCH=y
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+
+#
+# SCSI Transport Attributes
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_SATA is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_QLOGIC_FC is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+CONFIG_SCSI_QLA2XXX=y
+# CONFIG_SCSI_QLA21XX is not set
+# CONFIG_SCSI_QLA22XX is not set
+# CONFIG_SCSI_QLA2300 is not set
+# CONFIG_SCSI_QLA2322 is not set
+# CONFIG_SCSI_QLA6312 is not set
+# CONFIG_SCSI_QLA24XX is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+
+#
+# Macintosh device drivers
+#
+# CONFIG_WINDFARM is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+
+#
+# Tulip family network device support
+#
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+CONFIG_IBM_EMAC=y
+CONFIG_IBM_EMAC_RXB=64
+CONFIG_IBM_EMAC_TXB=8
+CONFIG_IBM_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_EMAC_DEBUG is not set
+CONFIG_IBM_EMAC_ZMII=y
+CONFIG_NET_PCI=y
+# CONFIG_PCNET32 is not set
+# CONFIG_AMD8111_ETH is not set
+# CONFIG_ADAPTEC_STARFIRE is not set
+# CONFIG_B44 is not set
+# CONFIG_FORCEDETH is not set
+# CONFIG_DGRS is not set
+# CONFIG_EEPRO100 is not set
+# CONFIG_E100 is not set
+# CONFIG_FEALNX is not set
+# CONFIG_NATSEMI is not set
+# CONFIG_NE2K_PCI is not set
+# CONFIG_8139CP is not set
+CONFIG_8139TOO=y
+CONFIG_8139TOO_PIO=y
+# CONFIG_8139TOO_TUNE_TWISTER is not set
+# CONFIG_8139TOO_8129 is not set
+# CONFIG_8139_OLD_RX_RESET is not set
+# CONFIG_SIS900 is not set
+# CONFIG_EPIC100 is not set
+# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
+# CONFIG_VIA_RHINE is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+# CONFIG_NET_RADIO is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_TELCLOCK is not set
+
+#
+# I2C support
+#
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_IBM_IIC=y
+# CONFIG_I2C_MPC is not set
+# CONFIG_I2C_MPC8260 is not set
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_SCx200_ACB is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
+# CONFIG_SENSORS_EEPROM is not set
+CONFIG_SENSORS_MAX6900=y
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCF8563 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_M41T00 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_RTC_X1205_I2C is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_FSCHER is not set
+# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Misc devices
+#
+
+#
+# Multimedia Capabilities Port drivers
+#
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_BANDWIDTH is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_SPLIT_ISO is not set
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+CONFIG_USB_UHCI_HCD=y
+# CONFIG_USB_SL811_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB Multimedia devices
+#
+# CONFIG_USB_DABUSB is not set
+
+#
+# Video4Linux support is needed for USB Multimedia device support
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGETKIT is not set
+# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# SN Devices
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_JBD is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_RELAYFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+
+#
+# Library routines
+#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_MAGIC_SYSRQ is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_KGDB is not set
+# CONFIG_XMON is not set
+CONFIG_BDI_SWITCH=y
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+CONFIG_PPC_OCP=y
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/platforms/4xx/Kconfig b/arch/ppc/platforms/4xx/Kconfig
index d883791..d1864ec 100644
--- a/arch/ppc/platforms/4xx/Kconfig
+++ b/arch/ppc/platforms/4xx/Kconfig
@@ -94,6 +94,12 @@ config OCOTEA
help
This option enables support for the IBM PPC440GX evaluation board.
+config P3P440
+ bool "P3P440"
+ select WANT_EARLY_SERIAL
+ help
+ This option enables support for the Prodrive P3P440 board.
+
endchoice
config EP405PC
@@ -117,7 +123,7 @@ config 440EP
config 440GP
bool
- depends on EBONY
+ depends on EBONY || P3P440
default y
config 440GX
@@ -169,7 +175,7 @@ config BOOKE
config IBM_OCP
bool
- depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT
+ depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || P3P440 || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT
default y
config XILINX_OCP
diff --git a/arch/ppc/platforms/4xx/Makefile b/arch/ppc/platforms/4xx/Makefile
index c9bb611..4f2e484 100644
--- a/arch/ppc/platforms/4xx/Makefile
+++ b/arch/ppc/platforms/4xx/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_BUBINGA) += bubinga.o
obj-$(CONFIG_LUAN) += luan.o
obj-$(CONFIG_YUCCA) += yucca.o
obj-$(CONFIG_OCOTEA) += ocotea.o
+obj-$(CONFIG_P3P440) += p3p440.o
obj-$(CONFIG_REDWOOD_5) += redwood5.o
obj-$(CONFIG_REDWOOD_6) += redwood6.o
obj-$(CONFIG_SYCAMORE) += sycamore.o
diff --git a/arch/ppc/platforms/4xx/ibm440gp.h b/arch/ppc/platforms/4xx/ibm440gp.h
index ae1efc0..59fe9e6 100644
--- a/arch/ppc/platforms/4xx/ibm440gp.h
+++ b/arch/ppc/platforms/4xx/ibm440gp.h
@@ -28,6 +28,11 @@
#define UART0_INT 0
#define UART1_INT 1
+/* GPIO macro register defines */
+#define GPIO_BASE 0x0000000140000700ULL
+#define GPIO0_OR (GPIO_BASE+0x0)
+#define GPIO0_IR (GPIO_BASE+0x1C)
+
/* Clock and Power Management */
#define IBM_CPM_IIC0 0x80000000 /* IIC interface */
#define IBM_CPM_IIC1 0x40000000 /* IIC interface */
diff --git a/arch/ppc/platforms/4xx/p3p440.c b/arch/ppc/platforms/4xx/p3p440.c
new file mode 100644
index 0000000..656dfc1
--- /dev/null
+++ b/arch/ppc/platforms/4xx/p3p440.c
@@ -0,0 +1,362 @@
+/*
+ * arch/ppc/platforms/4xx/p3p440.c
+ *
+ * P3P440 board specific routines
+ *
+ * Copyright (c) 2005 DENX Software Engineering
+ * Stefan Roese <sr@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/config.h>
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/reboot.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/major.h>
+#include <linux/blkdev.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/ide.h>
+#include <linux/initrd.h>
+#include <linux/seq_file.h>
+#include <linux/root_dev.h>
+#include <linux/tty.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/dma.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/ocp.h>
+#include <asm/pci-bridge.h>
+#include <asm/time.h>
+#include <asm/bootinfo.h>
+#include <asm/ppc4xx_pic.h>
+#include <asm/ppcboot.h>
+#include <asm/tlbflush.h>
+
+#include <syslib/gen550.h>
+#include <syslib/ibm440gp_common.h>
+
+#include <platforms/4xx/ibm440gp.h>
+
+extern bd_t __res;
+
+static struct ibm44x_clocks clocks __initdata;
+
+/*
+ * P3P440 external IRQ triggering/polarity settings
+ */
+unsigned char ppc4xx_uic_ext_irq_cfg[] __initdata = {
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ0: PCI_INTA */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ1: PCI_INTB */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ2: PCI_INTC */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ3: PCI_INTD */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ4: ETH INT */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* IRQ5: USB */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+ (IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE), /* */
+};
+
+static void __init
+p3p440_calibrate_decr(void)
+{
+ unsigned int freq;
+
+ freq = clocks.cpu;
+
+ ibm44x_calibrate_decr(freq);
+}
+
+static int
+p3p440_show_cpuinfo(struct seq_file *m)
+{
+ seq_printf(m, "vendor\t\t: Prodrive\n");
+ seq_printf(m, "machine\t\t: P3P440\n");
+
+ return 0;
+}
+
+#if defined(CONFIG_I2C_IBM_IIC) && defined(CONFIG_SENSORS_MAX6900)
+extern ulong max6900_get_rtc_time(void);
+extern int max6900_set_rtc_time(unsigned long nowtime);
+
+static int __init
+p3p440_rtc_hookup(void)
+{
+ struct timespec tv;
+
+ ppc_md.set_rtc_time = max6900_set_rtc_time;
+ ppc_md.get_rtc_time = max6900_get_rtc_time;
+
+ tv.tv_nsec = 0;
+ tv.tv_sec = (ppc_md.get_rtc_time)();
+ do_settimeofday(&tv);
+
+ return 0;
+}
+late_initcall(p3p440_rtc_hookup);
+#endif
+
+static inline int
+p3p440_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin)
+{
+ static char pci_irq_table[][4] =
+ /*
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ /*
+ * Note: PMC Module A has device id 0! This could
+ * be a problem, since the PPC440 pci bridge is located
+ * on this device. -sr
+ */
+ {PCI_INTB, PCI_INTC, PCI_INTD, PCI_INTA}, /* device 2 */
+ {PCI_INTC, PCI_INTD, PCI_INTA, PCI_INTB}, /* device 3 */
+ {PCI_INTD, PCI_INTA, PCI_INTB, PCI_INTC}, /* device 4 */
+ };
+
+ const long min_idsel = 2, max_idsel = 4, irqs_per_slot = 4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+#define PCIX_WRITEL(value, offset) \
+ (writel(value, pcix_reg_base + offset))
+
+/*
+ * FIXME: This is only here to "make it work". This will move
+ * to a ibm_pcix.c which will contain a generic IBM PCIX bridge
+ * configuration library. -Matt
+ */
+static void __init
+p3p440_setup_pcix(void)
+{
+ void __iomem *pcix_reg_base;
+
+ pcix_reg_base = ioremap64(PCIX0_REG_BASE, PCIX_REG_SIZE);
+
+ /* Disable all windows */
+ PCIX_WRITEL(0, PCIX0_POM0SA);
+ PCIX_WRITEL(0, PCIX0_POM1SA);
+ PCIX_WRITEL(0, PCIX0_POM2SA);
+ PCIX_WRITEL(0, PCIX0_PIM0SA);
+ PCIX_WRITEL(0, PCIX0_PIM1SA);
+ PCIX_WRITEL(0, PCIX0_PIM2SA);
+
+ /* Setup 2GB PLB->PCI outbound mem window (3_8000_0000->0_8000_0000) */
+ PCIX_WRITEL(0x00000003, PCIX0_POM0LAH);
+ PCIX_WRITEL(0x80000000, PCIX0_POM0LAL);
+ PCIX_WRITEL(0x00000000, PCIX0_POM0PCIAH);
+ PCIX_WRITEL(0x80000000, PCIX0_POM0PCIAL);
+ PCIX_WRITEL(0x80000001, PCIX0_POM0SA);
+
+ /* Setup 2GB PCI->PLB inbound memory window at 0, enable MSIs */
+ PCIX_WRITEL(0x00000000, PCIX0_PIM0LAH);
+ PCIX_WRITEL(0x00000000, PCIX0_PIM0LAL);
+ PCIX_WRITEL(0x80000007, PCIX0_PIM0SA);
+
+ eieio();
+}
+
+static int is_monarch(void)
+{
+ void __iomem *gpio_base;
+ ulong val;
+
+ gpio_base = ioremap64(GPIO_BASE, 0x1000);
+ val = in_be32((void *)(gpio_base+0x1c));
+ iounmap((void *)gpio_base);
+
+ if (val & CFG_MONARCH_IO)
+ return 0;
+ else
+ return 1;
+}
+
+static void __init
+p3p440_setup_hose(void)
+{
+ struct pci_controller *hose;
+
+ if (!is_monarch()) {
+ /*
+ * REMARK: This Non-Monarch mode need perhaps some changes.
+ * It's not tested at all, because of lack of hardware. --sr
+ */
+ printk("P3P440-PCI: Non-Monarch detected, skipping PCI init!\n");
+ return;
+ }
+
+ /* Configure windows on the PCI-X host bridge */
+ p3p440_setup_pcix();
+
+ hose = pcibios_alloc_controller();
+
+ if (!hose)
+ return;
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ hose->pci_mem_offset = P3P440_PCI_MEM_OFFSET;
+
+ pci_init_resource(&hose->io_resource,
+ P3P440_PCI_LOWER_IO,
+ P3P440_PCI_UPPER_IO,
+ IORESOURCE_IO,
+ "PCI host bridge");
+
+ pci_init_resource(&hose->mem_resources[0],
+ P3P440_PCI_LOWER_MEM,
+ P3P440_PCI_UPPER_MEM,
+ IORESOURCE_MEM,
+ "PCI host bridge");
+
+ hose->io_space.start = P3P440_PCI_LOWER_IO;
+ hose->io_space.end = P3P440_PCI_UPPER_IO;
+ hose->mem_space.start = P3P440_PCI_LOWER_MEM;
+ hose->mem_space.end = P3P440_PCI_UPPER_MEM;
+ hose->io_base_virt = ioremap64(P3P440_PCI_IO_BASE, P3P440_PCI_IO_SIZE);
+ isa_io_base = (unsigned long)hose->io_base_virt;
+
+ setup_indirect_pci(hose,
+ P3P440_PCI_CFGA_PLB32,
+ P3P440_PCI_CFGD_PLB32);
+ hose->set_cfg_type = 1;
+
+ hose->last_busno = pciauto_bus_scan(hose, hose->first_busno);
+
+ ppc_md.pci_swizzle = common_swizzle;
+ ppc_md.pci_map_irq = p3p440_map_irq;
+}
+
+static void __init
+p3p440_early_serial_map(void)
+{
+ struct uart_port port;
+
+ /* Setup ioremapped serial port access */
+ memset(&port, 0, sizeof(port));
+ port.membase = ioremap64(PPC440GP_UART0_ADDR, 8);
+ port.irq = 0;
+ port.uartclk = clocks.uart0;
+ port.regshift = 0;
+ port.iotype = SERIAL_IO_MEM;
+ port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
+ port.line = 0;
+
+ if (early_serial_setup(&port) != 0) {
+ printk("Early serial init of port 0 failed\n");
+ }
+
+#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
+ /* Configure debug serial access */
+ gen550_init(0, &port);
+
+ /* Purge TLB entry added in head_44x.S for early serial access */
+ _tlbie(UART0_IO_BASE);
+#endif
+
+ port.membase = ioremap64(PPC440GP_UART1_ADDR, 8);
+ port.irq = 1;
+ port.uartclk = clocks.uart1;
+ port.line = 1;
+
+ if (early_serial_setup(&port) != 0) {
+ printk("Early serial init of port 1 failed\n");
+ }
+
+#if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB)
+ /* Configure debug serial access */
+ gen550_init(1, &port);
+#endif
+}
+
+static void __init
+p3p440_setup_arch(void)
+{
+ struct ocp_def *def;
+ struct ocp_func_emac_data *emacdata;
+
+ /* Set mac_addr for each EMAC */
+ def = ocp_get_one_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC, 0);
+ emacdata = def->additions;
+ emacdata->phy_map = 0x00000001; /* Skip 0x00 */
+ emacdata->phy_mode = PHY_MODE_RMII;
+ memcpy(emacdata->mac_addr, __res.bi_enetaddr, 6);
+
+ def = ocp_get_one_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC, 1);
+ emacdata = def->additions;
+ emacdata->phy_map = 0x00000001; /* Skip 0x00 */
+ emacdata->phy_mode = PHY_MODE_RMII;
+ memcpy(emacdata->mac_addr, __res.bi_enet1addr, 6);
+
+ /*
+ * Determine various clocks.
+ * To be completely correct we should get SysClk
+ * from FPGA, because it can be changed by on-board switches
+ * --ebs
+ */
+ ibm440gp_get_clocks(&clocks, 33333333, 0);
+ ocp_sys_info.opb_bus_freq = clocks.opb;
+
+ /* init to some ~sane value until calibrate_delay() runs */
+ loops_per_jiffy = 50000000/HZ;
+
+ /* Setup PCI host bridge */
+ p3p440_setup_hose();
+
+#ifdef CONFIG_BLK_DEV_INITRD
+ if (initrd_start)
+ ROOT_DEV = Root_RAM0;
+ else
+#endif
+#ifdef CONFIG_ROOT_NFS
+ ROOT_DEV = Root_NFS;
+#else
+ ROOT_DEV = Root_HDA1;
+#endif
+
+ p3p440_early_serial_map();
+
+ /* Identify the system */
+ printk("Prodrive P3P440 port (DENX Software Engineering (sr@denx.de))\n");
+}
+
+void __init platform_init(unsigned long r3, unsigned long r4,
+ unsigned long r5, unsigned long r6, unsigned long r7)
+{
+ ibm44x_platform_init(r3, r4, r5, r6, r7);
+
+ ppc_md.setup_arch = p3p440_setup_arch;
+ ppc_md.show_cpuinfo = p3p440_show_cpuinfo;
+ ppc_md.get_irq = NULL; /* Set in ppc4xx_pic_init() */
+
+ ppc_md.calibrate_decr = p3p440_calibrate_decr;
+ ppc_md.time_init = NULL;
+ ppc_md.set_rtc_time = NULL;
+ ppc_md.get_rtc_time = NULL;
+
+#ifdef CONFIG_KGDB
+ ppc_md.early_serial_map = p3p440_early_serial_map;
+#endif
+}
+
diff --git a/arch/ppc/platforms/4xx/p3p440.h b/arch/ppc/platforms/4xx/p3p440.h
new file mode 100644
index 0000000..bd1b68a
--- /dev/null
+++ b/arch/ppc/platforms/4xx/p3p440.h
@@ -0,0 +1,72 @@
+/*
+ * arch/ppc/platforms/p3p440.h
+ *
+ * P3P440 board definitions
+ *
+ * Copyright (c) 2005 DENX Software Engineering
+ * Stefan Roese <sr@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_P3P440_H__
+#define __ASM_P3P440_H__
+
+#include <linux/config.h>
+#include <platforms/4xx/ibm440gp.h>
+
+/*
+ * Serial port defines
+ */
+
+/* head_44x.S created UART mapping, used before early_serial_setup.
+ * We cannot use default OpenBIOS UART mappings because they
+ * don't work for configurations with more than 512M RAM. --ebs
+ */
+#define UART0_IO_BASE 0xF0000200
+#define UART1_IO_BASE 0xF0000300
+
+/* no external clock used, will be filled dynamically */
+#define BASE_BAUD 691200
+
+#define STD_UART_OP(num) \
+ { 0, BASE_BAUD, 0, UART##num##_INT, \
+ (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \
+ iomem_base: (void*)UART##num##_IO_BASE, \
+ io_type: SERIAL_IO_MEM},
+
+#define SERIAL_PORT_DFNS \
+ STD_UART_OP(0) \
+ STD_UART_OP(1)
+
+/* PCI support */
+#define P3P440_PCI_LOWER_IO 0x00000000
+#define P3P440_PCI_UPPER_IO 0x0000ffff
+#define P3P440_PCI_LOWER_MEM 0x80002000
+#define P3P440_PCI_UPPER_MEM 0xffffefff
+
+#define P3P440_PCI_CFGREGS_BASE 0x000000020ec00000
+#define P3P440_PCI_CFGA_PLB32 0x0ec00000
+#define P3P440_PCI_CFGD_PLB32 0x0ec00004
+
+#define P3P440_PCI_IO_BASE 0x0000000208000000ULL
+#define P3P440_PCI_IO_SIZE 0x00010000
+#define P3P440_PCI_MEM_OFFSET 0x00000000
+
+#define PCI_INTA 23
+#define PCI_INTB 24
+#define PCI_INTC 25
+#define PCI_INTD 26
+
+#define CFG_GPIO_RDY (0x80000000 >> 11)
+#define CFG_MONARCH_IO (0x80000000 >> 18)
+#define CFG_EREADY_IO (0x80000000 >> 20)
+#define CFG_LED_GREEN (0x80000000 >> 21)
+#define CFG_LED_RED (0x80000000 >> 22)
+
+#endif /* __ASM_P3P440_H__ */
+#endif /* __KERNEL__ */
diff --git a/arch/ppc/syslib/Makefile b/arch/ppc/syslib/Makefile
index 5b7f2b8..82a0924 100644
--- a/arch/ppc/syslib/Makefile
+++ b/arch/ppc/syslib/Makefile
@@ -28,7 +28,6 @@ endif
endif
obj-$(CONFIG_44x) += ppc4xx_pic.o
obj-$(CONFIG_40x) += ppc4xx_setup.o
-obj-$(CONFIG_GEN_RTC) += todc_time.o
obj-$(CONFIG_PPC4xx_DMA) += ppc4xx_dma.o
obj-$(CONFIG_PPC4xx_EDMA) += ppc4xx_sgdma.o
ifeq ($(CONFIG_40x),y)
@@ -44,8 +43,11 @@ obj-$(CONFIG_POWER4) += open_pic2.o
obj-$(CONFIG_PPC_CHRP) += open_pic.o
obj-$(CONFIG_PPC_PREP) += open_pic.o todc_time.o
obj-$(CONFIG_BAMBOO) += pci_auto.o todc_time.o
+obj-$(CONFIG_BUBINGA) += todc_time.o
+obj-$(CONFIG_CPCI405) += todc_time.o
obj-$(CONFIG_CPCI690) += todc_time.o pci_auto.o
obj-$(CONFIG_EBONY) += pci_auto.o todc_time.o
+obj-$(CONFIG_EP405) += todc_time.o
obj-$(CONFIG_EV64260) += todc_time.o pci_auto.o
obj-$(CONFIG_EV64360) += todc_time.o
obj-$(CONFIG_CHESTNUT) += mv64360_pic.o pci_auto.o
@@ -61,6 +63,7 @@ obj-$(CONFIG_MV64X60) += mv64x60.o mv64
obj-$(CONFIG_MVME5100) += open_pic.o todc_time.o \
pci_auto.o hawk_common.o
obj-$(CONFIG_OCOTEA) += pci_auto.o todc_time.o
+obj-$(CONFIG_P3P440) += pci_auto.o
obj-$(CONFIG_PAL4) += cpc700_pic.o
obj-$(CONFIG_POWERPMC250) += pci_auto.o
obj-$(CONFIG_PPLUS) += hawk_common.o open_pic.o \
@@ -74,6 +77,8 @@ obj-$(CONFIG_SANDPOINT) += pci_auto.o t
obj-$(CONFIG_SBC82xx) += todc_time.o
obj-$(CONFIG_SPRUCE) += cpc700_pic.o pci_auto.o \
todc_time.o
+obj-$(CONFIG_SYCAMORE) += todc_time.o
+obj-$(CONFIG_WALNUT) += todc_time.o
obj-$(CONFIG_8260) += m8260_setup.o pq2_devices.o pq2_sys.o \
ppc_sys.o
obj-$(CONFIG_PCI_8260) += m82xx_pci.o pci_auto.o
diff --git a/include/asm-ppc/ibm4xx.h b/include/asm-ppc/ibm4xx.h
index 6c28ae7..510d98a 100644
--- a/include/asm-ppc/ibm4xx.h
+++ b/include/asm-ppc/ibm4xx.h
@@ -105,6 +105,10 @@ void ppc4xx_init(unsigned long r3, unsig
#include <platforms/4xx/ocotea.h>
#endif
+#if defined(CONFIG_P3P440)
+#include <platforms/4xx/p3p440.h>
+#endif
+
#ifndef __ASSEMBLY__
#ifdef CONFIG_40x
/*
\f
!-------------------------------------------------------------flip-
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox