* Machine automagically reboots with 2.6.23-rc2-mm2
From: Balbir Singh @ 2007-08-16 21:32 UTC (permalink / raw)
To: Andrew Morton; +Cc: linuxppc-dev, linux kernel mailing list
[-- Attachment #1: Type: text/plain, Size: 2545 bytes --]
Hi,
My machine reboots automatically after a few seconds of booting 2.6.23-rc2-mm2.
I've tried several ways to debug the problem, but I've had no success.
I am not sure if this problem has been reported already, a few simple searches
did not indicate that the problem had been reported
2.6.23-rc1-mm1 did not have this problem.
.config is attached with this email.
/proc/cpuinfo shows
processor : 0
cpu : POWER5 (gr)
clock : 1654.344000MHz
revision : 2.3 (pvr 003a 0203)
processor : 1
cpu : POWER5 (gr)
clock : 1654.344000MHz
revision : 2.3 (pvr 003a 0203)
processor : 2
cpu : POWER5 (gr)
clock : 1654.344000MHz
revision : 2.3 (pvr 003a 0203)
processor : 3
cpu : POWER5 (gr)
clock : 1654.344000MHz
revision : 2.3 (pvr 003a 0203)
timebase : 206998000
machine : CHRP IBM,9123-710
lspci shows
00:02.0 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
00:02.2 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
00:02.3 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
00:02.4 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
c0:01.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
c0:01.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
c8:01.0 USB Controller: NEC Corporation USB (rev 43)
c8:01.1 USB Controller: NEC Corporation USB (rev 43)
c8:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
cc:01.0 Mass storage controller: Promise Technology, Inc. 20275 (rev 01)
d0:01.0 SCSI storage controller: Mylex Corporation AcceleRAID 600/500/400/Sapphire support Device (rev 04)
0001:00:02.2 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
0001:00:02.4 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
0001:00:02.6 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
0001:d0:01.0 Ethernet controller: Intel Corporation 82545GM Gigabit Ethernet Controller (rev 04)
Normal kernel boot (memory info)
EEH: PCI Enhanced I/O Error Handling Enabled
PPC64 nvram contains 7168 bytes
Using dedicated idle loop
Top of RAM: 0xe9000000, Total RAM: 0xe9000000
Memory hole size: 0MB
On node 0 totalpages: 954368
DMA zone: 954368 pages, LIFO batch:31
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
[boot]0015 Setup Done
Built 1 zonelists
--
Warm Regards,
Balbir Singh
Linux Technology Center
IBM, ISTL
[-- Attachment #2: config.txt --]
[-- Type: text/plain, Size: 40036 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.23-rc2-mm2
# Thu Aug 16 15:02:55 2007
#
CONFIG_PPC64=y
#
# Processor support
#
# CONFIG_POWER4_ONLY is not set
CONFIG_POWER3=y
CONFIG_POWER4=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=32
CONFIG_64BIT=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_ARCH_HAS_ILOG2_U64=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_OF=y
CONFIG_PPC_UDBG_16550=y
CONFIG_GENERIC_TBSYNC=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_PPC64_SWSUSP=y
# CONFIG_PPC_DCR_NATIVE is not set
CONFIG_PPC_DCR_MMIO=y
CONFIG_PPC_DCR=y
CONFIG_PPC_OF_PLATFORM_PCI=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SWAP_PREFETCH=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
CONFIG_TASK_XACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_CONTAINERS=y
CONFIG_CONTAINER_DEBUG=y
# CONFIG_CONTAINER_NS is not set
CONFIG_CONTAINER_CPUACCT=y
CONFIG_CPUSETS=y
CONFIG_RESOURCE_COUNTERS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_CONTAINER_MEM_CONT=y
CONFIG_PROC_PID_CPUSET=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_PROC_KPAGEMAP=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_BLK_DEV_IO_TRACE=y
# CONFIG_BLK_DEV_BSG is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
#
# Platform support
#
CONFIG_PPC_MULTIPLATFORM=y
# CONFIG_EMBEDDED6xx is not set
# CONFIG_PPC_82xx is not set
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
CONFIG_PPC_PSERIES=y
CONFIG_PPC_SPLPAR=y
CONFIG_EEH=y
CONFIG_SCANLOG=m
CONFIG_LPARCFG=y
CONFIG_PPC_ISERIES=y
#
# iSeries device drivers
#
CONFIG_VIODASD=y
CONFIG_VIOCD=m
CONFIG_VIOTAPE=m
CONFIG_VIOPATH=y
# CONFIG_PPC_MPC52xx is not set
# CONFIG_PPC_MPC5200 is not set
CONFIG_PPC_PMAC=y
CONFIG_PPC_PMAC64=y
CONFIG_PPC_MAPLE=y
# CONFIG_PPC_PASEMI is not set
# CONFIG_PPC_CELLEB is not set
# CONFIG_PPC_PS3 is not set
CONFIG_PPC_CELL=y
CONFIG_PPC_CELL_NATIVE=y
CONFIG_PPC_IBM_CELL_BLADE=y
#
# Cell Broadband Engine options
#
CONFIG_SPU_FS=m
CONFIG_SPU_FS_64K_LS=y
CONFIG_SPU_BASE=y
CONFIG_CBE_RAS=y
CONFIG_CBE_THERM=m
# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
CONFIG_UDBG_RTAS_CONSOLE=y
CONFIG_XICS=y
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
CONFIG_PPC_I8259=y
CONFIG_U3_DART=y
CONFIG_PPC_RTAS=y
CONFIG_RTAS_ERROR_LOGGING=y
CONFIG_RTAS_PROC=y
CONFIG_RTAS_FLASH=m
CONFIG_PPC_PMI=m
CONFIG_MMIO_NVRAM=y
CONFIG_MPIC_U3_HT_IRQS=y
CONFIG_IBMVIO=y
# CONFIG_IBMEBUS is not set
# CONFIG_PPC_MPC106 is not set
CONFIG_PPC_970_NAP=y
CONFIG_PPC_INDIRECT_IO=y
CONFIG_GENERIC_IOMAP=y
# CONFIG_CPU_FREQ is not set
# CONFIG_CPM2 is not set
CONFIG_AXON_RAM=m
#
# Kernel options
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
# CONFIG_PREEMPT_BKL is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_IOMMU_VMERGE=y
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_MEMORY_HOTPLUG=y
CONFIG_MEMORY_HOTPLUG_SPARSE=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_SPARSEMEM_VMEMMAP=y
CONFIG_ARCH_POPULATES_SPARSEMEM_VMEMMAP=y
CONFIG_ARCH_MEMORY_PROBE=y
CONFIG_PPC_HAS_HASH_64K=y
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_SCHED_SMT is not set
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
CONFIG_SECCOMP=y
# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_SYSCALL=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=y
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=y
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
# CONFIG_NF_CT_PROTO_UDPLITE is not set
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
# CONFIG_NETFILTER_XTABLES is not set
#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
CONFIG_LLC=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Wireless
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_OF_DEVICE=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_PLATFORM is not set
#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
CONFIG_SCSI_ISCSI_ATTRS=m
# CONFIG_SCSI_SAS_LIBSAS is not set
CONFIG_SCSI_SRP_ATTRS=y
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
CONFIG_SCSI_IBMVSCSI=y
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
CONFIG_SCSI_IPR=y
CONFIG_SCSI_IPR_TRACE=y
CONFIG_SCSI_IPR_DUMP=y
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
CONFIG_SCSI_LPFC=m
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
CONFIG_SCSI_DEBUG=m
# CONFIG_SCSI_SRP is not set
CONFIG_ATA=y
CONFIG_ATA_NONSTANDARD=y
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_SVW=y
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
CONFIG_PATA_WINBOND=y
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID10=y
CONFIG_MD_RAID456=y
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
# CONFIG_DM_MULTIPATH_RDAC is not set
# CONFIG_DM_DELAY is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
#
# Controllers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
#
# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=y
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB_PMU=y
# CONFIG_ADB_PMU_LED is not set
CONFIG_PMAC_SMU=y
# CONFIG_MAC_EMUMOUSEBTN is not set
CONFIG_THERM_PM72=y
CONFIG_WINDFARM=y
CONFIG_WINDFARM_PM112=y
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
CONFIG_SUNGEM=y
# CONFIG_CASSINI is not set
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=y
# CONFIG_TYPHOON is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
CONFIG_IBMVETH=m
CONFIG_NET_PCI=y
CONFIG_PCNET32=y
# CONFIG_PCNET32_NAPI is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_FORCEDETH is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=y
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
CONFIG_NETDEV_1000=y
CONFIG_ACENIC=y
CONFIG_ACENIC_OMIT_TIGON_I=y
# CONFIG_DL2K is not set
CONFIG_E1000=y
# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
CONFIG_SPIDER_NET=m
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
# CONFIG_IXGBE is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_PASEMI_MAC is not set
# CONFIG_MLX4_CORE is not set
CONFIG_TR=y
CONFIG_IBMOL=y
# CONFIG_3C359 is not set
# CONFIG_TMS380TR is not set
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
CONFIG_ISERIES_VETH=m
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_PPP_MPPE is not set
CONFIG_PPPOE=m
# CONFIG_PPPOL2TP is not set
# CONFIG_SLIP is not set
CONFIG_SLHC=m
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_ATI_REMOTE is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_PMACZILOG is not set
CONFIG_SERIAL_ICOM=m
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_HVC_DRIVER=y
CONFIG_HVC_CONSOLE=y
CONFIG_HVC_ISERIES=y
CONFIG_HVC_RTAS=y
CONFIG_HVCS=m
# CONFIG_IPMI_HANDLER is not set
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# CONFIG_DRM is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
# CONFIG_HANGCHECK_TIMER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
CONFIG_I2C_AMD8111=y
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_POWERMAC=y
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_SENSORS_DS1682 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
CONFIG_DAB=y
# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_BACKLIGHT_CLASS_DEVICE=y
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
CONFIG_FB_MATROX=y
CONFIG_FB_MATROX_MILLENIUM=y
CONFIG_FB_MATROX_MYSTIQUE=y
CONFIG_FB_MATROX_G=y
CONFIG_FB_MATROX_I2C=m
CONFIG_FB_MATROX_MAVEN=m
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
CONFIG_FB_IBM_GXT4500=y
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_FB_LOGO_EXTRA=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
#
# ALSA PowerMac devices
#
CONFIG_SND_POWERMAC=m
CONFIG_SND_POWERMAC_AUTO_DRC=y
#
# ALSA PowerPC devices
#
#
# Apple Onboard Audio driver
#
CONFIG_SND_AOA=m
CONFIG_SND_AOA_FABRIC_LAYOUT=m
CONFIG_SND_AOA_ONYX=m
CONFIG_SND_AOA_TAS=m
CONFIG_SND_AOA_TOONIE=m
CONFIG_SND_AOA_SOUNDBUS=m
CONFIG_SND_AOA_SOUNDBUS_I2S=m
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
# CONFIG_SND_USB_CAIAQ is not set
#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set
#
# SoC Audio support for SuperH
#
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
CONFIG_USB_OHCI_HCD_PCI=y
CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
CONFIG_USB_APPLEDISPLAY=m
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_GOTEMP is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
# CONFIG_NEW_LEDS is not set
CONFIG_INFINIBAND=m
# CONFIG_INFINIBAND_USER_MAD is not set
# CONFIG_INFINIBAND_USER_ACCESS is not set
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
# CONFIG_INFINIBAND_AMSO1100 is not set
# CONFIG_MLX4_INFINIBAND is not set
CONFIG_INFINIBAND_IPOIB=m
# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
# CONFIG_INFINIBAND_SRP is not set
CONFIG_INFINIBAND_ISER=m
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
CONFIG_DCA=m
#
# Userspace I/O
#
# CONFIG_UIO is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISER4_FS is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=y
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
# CONFIG_XFS_QUOTA is not set
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=m
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
# CONFIG_JOLIET is not set
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# Layered filesystems
#
# CONFIG_UNION_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_WEAK_PW_HASH is not set
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Distributed Lock Manager
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_PAGE_OWNER is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_MUTEXES=y
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_PROFILE_LIKELY is not set
CONFIG_FORCED_INLINING=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_DEBUG_SYNCHRO_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_WANT_EXTRA_DEBUG_INFORMATION is not set
# CONFIG_UNWIND_INFO is not set
# CONFIG_KGDB is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_HCALL_STATS is not set
CONFIG_XMON=y
# CONFIG_XMON_DEFAULT is not set
CONFIG_XMON_DISASSEMBLY=y
CONFIG_DEBUGGER=y
CONFIG_IRQSTACKS=y
CONFIG_BOOTX_TEXT=y
# CONFIG_PPC_EARLY_DEBUG is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_XOR_BLOCKS=y
CONFIG_ASYNC_CORE=y
CONFIG_ASYNC_MEMCPY=y
CONFIG_ASYNC_XOR=y
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_HW=y
^ permalink raw reply
* Re: external IRQ's
From: robert lazarski @ 2007-08-16 21:34 UTC (permalink / raw)
Cc: linuxppc-embedded
In-Reply-To: <46C47A1D.5030303@freescale.com>
On 8/16/07, Scott Wood <scottwood@freescale.com> wrote:
> robert lazarski wrote:
> > 1) Do I need to define those external IRQ's in both a device tree file
> > under arch/powerpc/boot/dts and also in C code under
> > arch/powerpc/platforms/85xx ?
>
> Just in the dts.
Thanks, I notice in 2.6.23-rc3 there no longer are a series of
mpic_assign_isu() .
>
> I don't know what version of the dts you're looking at, but the one in
> the current Linux tree has <5 1>, not <35 0>.
Thanks for pointing that out! 2.6.22.2 has 35 as the interrupt, while
2.6.23-rc3 has 5. 35 didn't make any sense to me since the old ppc
arch used 5.
>
> > I'm also not getting the ethernet interrupts in the above cds example:
> >
> > interrupts = <d 2 e 2 12 2>;
> >
> > Why start with 'd' and 'e' ? I noticed many if not all boards do that.
>
> In the current dts, it's <1d 2 1e 2 22 2>.
>
> It appears that the interrupt numbering was changed not too long ago,
> and that external interrupts used to be numbered above the internal ones.
>
> -Scott
>
Why <1d 2 1e 2 22 2> ? I can't seem to parse these numbers - how do I
know what to use for my external interupts 1,2 for phy's 0,1 using a
88E1121R and for external interupts 3,4 for phy's 2,3 using a 88E1111
?
Thanks!
Robert
^ permalink raw reply
* Re: external IRQ's
From: Scott Wood @ 2007-08-16 21:43 UTC (permalink / raw)
To: robert lazarski; +Cc: linuxppc-embedded
In-Reply-To: <f87675ee0708161434i9f38b0dg123a767822cf7402@mail.gmail.com>
robert lazarski wrote:
> Why <1d 2 1e 2 22 2> ? I can't seem to parse these numbers
They alternate between IRQ numbers and level/sense information, and the
IRQ numbers are the internal IRQ number plus 16.
> - how do I
> know what to use for my external interupts 1,2 for phy's 0,1 using a
> 88E1121R and for external interupts 3,4 for phy's 2,3 using a 88E1111
> ?
I thought it was interrupts 0-3, not 1-4?
If, like the CDS board, you have level-triggered active-low phy
interrupts, then <0 1>, <1 1>, <2 1>, and <3 1>. If not, then choose an
appropriate value for the second cell based on booting-without-of.txt.
-Scott
^ permalink raw reply
* Re: [PATCH 1/2] Add scaled time to taskstats based process accounting
From: Paul Mackerras @ 2007-08-16 22:22 UTC (permalink / raw)
To: Linas Vepstas
Cc: Andrew Morton, linuxppc-dev, Michael Neuling, linux-kernel,
Balbir Singh
In-Reply-To: <20070816163850.GU4261@austin.ibm.com>
Linas Vepstas writes:
> My gut impression (maybe wrong?) is that the scaled time is,
> in a certain sense, "more accurate" than the unscaled time.
The "unscaled" time is just time, as in "how many seconds did this
task spend on the CPU". It's what all the tools (except a certain
proprietary workload manager) expect. Top, ps, etc. get unhappy if
the times reported (user, system, hardirq, softirq, idle, stolen)
don't add up to elapsed wall-clock time.
The "scaled" time is really CPU cycles divided by some arbitrary
factor (the notional CPU frequency). So yes it does give some
indication of how much progress the task should have made, in some
sense.
Both measures are useful. Because the current user API is in terms of
real time rather than cycles, we have to continue reporting real time,
not scaled time, which is why the existing interfaces report unscaled
time, and the scaled time values are reported through a new extension
to the taskstats interface.
Paul.
^ permalink raw reply
* Re: 2.6.23-rc3 broken on G5
From: Paul Mackerras @ 2007-08-16 22:23 UTC (permalink / raw)
To: Andreas Schwab; +Cc: linuxppc-dev
In-Reply-To: <jelkccftt6.fsf@sykes.suse.de>
Andreas Schwab writes:
> This change:
>
> commit edd0622bd2e8f755c960827e15aa6908c3c5aa94
> Author: Paul Mackerras <paulus@samba.org>
> Date: Fri Aug 10 21:04:07 2007 +1000
>
> [POWERPC] Fix potential duplicate entry in SLB shadow buffer
>
> is broken on PowerMac G5. It crashes very early, before the bootx
> console is set up.
Hmmm. It (current Linus git) works fine on my dual 2.0GHz G5.
What sort of G5 do you have and what is your .config?
Paul.
^ permalink raw reply
* [PATCH] powerpc: add setclrbits macros
From: Timur Tabi @ 2007-08-16 22:43 UTC (permalink / raw)
To: linuxppc-dev, Geert.Uytterhoeven, michael, paulus, galak, benh; +Cc: Timur Tabi
This patch adds the setclrbits_xxx() macros, which are used to set and clear
multiple bits in a single read-modify-write operation. Specify the bits
to set in the 'set' parameter and the bits to clear in the 'clear' parameter.
These macros can also be used to set a multiple-bit bit pattern using a mask,
by specifying the mask in the 'clear' parameter and the new bit pattern in the
'set' parameter. There are big-endian and little-endian versions for 8, 16,
32, and 64 bits.
Signed-off-by: Timur Tabi <timur@freescale.com>
---
Changed the macros from setmaskedbits_xxx to setclrbits_xxx and added a comment
indicating the expanded functionality.
include/asm-powerpc/io.h | 27 +++++++++++++++++++++++++++
1 files changed, 27 insertions(+), 0 deletions(-)
diff --git a/include/asm-powerpc/io.h b/include/asm-powerpc/io.h
index bb8d965..58c8b96 100644
--- a/include/asm-powerpc/io.h
+++ b/include/asm-powerpc/io.h
@@ -734,6 +734,33 @@ static inline void * bus_to_virt(unsigned long address)
#define setbits16(_addr, _v) out_be16((_addr), in_be16(_addr) | (_v))
#define clrbits16(_addr, _v) out_be16((_addr), in_be16(_addr) & ~(_v))
+/* Set and clear bits in one shot. These macros can be used to clear and
+ * set multiple bits in a register using a single read-modify-write. These
+ * macros can also be used to set a multiple-bit bit pattern using a mask,
+ * by specifying the mask in the 'clear' parameter and the new bit pattern
+ * in the 'set' parameter.
+ */
+
+#ifdef __powerpc64__
+#define setclrbits_be64(addr, set, clear) \
+ out_be64((addr), (in_be64(addr) & ~(clear)) | (set))
+#define setclrbits_le64(addr, set, clear) \
+ out_le64((addr), (in_le64(addr) & ~(clear)) | (set))
+#endif
+
+#define setclrbits_be32(addr, set, clear) \
+ out_be32((addr), (in_be32(addr) & ~(clear)) | (set))
+#define setclrbits_be16(addr, set, clear) \
+ out_be16((addr), (in_be16(addr) & ~(clear)) | (set))
+
+#define setclrbits_le32(addr, set, clear) \
+ out_le32((addr), (in_le32(addr) & ~(clear)) | (set))
+#define setclrbits_le16(addr, set, clear) \
+ out_le16((addr), (in_le16(addr) & ~(clear)) | (set))
+
+#define setclrbits_8(addr, set, clear) \
+ out_8((addr), (in_8(addr) & ~(clear)) | (set))
+
#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_IO_H */
--
1.5.2.4
^ permalink raw reply related
* Re: 2.6.23-rc3 broken on G5
From: Andreas Schwab @ 2007-08-16 22:46 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev
In-Reply-To: <18116.52843.212978.281399@cargo.ozlabs.ibm.com>
[-- Attachment #1: Type: text/plain, Size: 874 bytes --]
Paul Mackerras <paulus@samba.org> writes:
> Andreas Schwab writes:
>
>> This change:
>>
>> commit edd0622bd2e8f755c960827e15aa6908c3c5aa94
>> Author: Paul Mackerras <paulus@samba.org>
>> Date: Fri Aug 10 21:04:07 2007 +1000
>>
>> [POWERPC] Fix potential duplicate entry in SLB shadow buffer
>>
>> is broken on PowerMac G5. It crashes very early, before the bootx
>> console is set up.
I also tried PPC_EARLY_DEBUG, but that didn't show anything either.
> Hmmm. It (current Linus git) works fine on my dual 2.0GHz G5.
>
> What sort of G5 do you have and what is your .config?
It's a dual 1.8GHz. Config is attached.
Andreas.
--
Andreas Schwab, SuSE Labs, schwab@suse.de
SuSE Linux Products GmbH, Maxfeldstraße 5, 90409 Nürnberg, Germany
PGP key fingerprint = 58CA 54C7 6D53 942B 1756 01D3 44D5 214B 8276 4ED5
"And now for something completely different."
[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 55847 bytes --]
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.23-rc3
# Wed Aug 15 22:14:06 2007
#
CONFIG_PPC64=y
#
# Processor support
#
CONFIG_POWER4_ONLY=y
CONFIG_POWER4=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_64BIT=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_ARCH_HAS_ILOG2_U64=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
CONFIG_OF=y
# CONFIG_PPC_UDBG_16550 is not set
CONFIG_GENERIC_TBSYNC=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_PPC64_SWSUSP=y
# CONFIG_PPC_DCR_NATIVE is not set
# CONFIG_PPC_DCR_MMIO is not set
# CONFIG_PPC_OF_PLATFORM_PCI is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
CONFIG_TASK_XACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
CONFIG_USER_NS=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=19
CONFIG_CPUSETS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_BLK_DEV_IO_TRACE=y
CONFIG_BLK_DEV_BSG=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
#
# Platform support
#
CONFIG_PPC_MULTIPLATFORM=y
# CONFIG_EMBEDDED6xx is not set
# CONFIG_PPC_82xx is not set
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_86xx is not set
# CONFIG_PPC_PSERIES is not set
# CONFIG_PPC_ISERIES is not set
# CONFIG_PPC_MPC52xx is not set
# CONFIG_PPC_MPC5200 is not set
CONFIG_PPC_PMAC=y
CONFIG_PPC_PMAC64=y
# CONFIG_PPC_MAPLE is not set
# CONFIG_PPC_PASEMI is not set
# CONFIG_PPC_CELLEB is not set
# CONFIG_PPC_PS3 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_IBM_CELL_BLADE is not set
# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
CONFIG_MPIC=y
# CONFIG_MPIC_WEIRD is not set
# CONFIG_PPC_I8259 is not set
CONFIG_U3_DART=y
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
CONFIG_MPIC_U3_HT_IRQS=y
# CONFIG_PPC_MPC106 is not set
CONFIG_PPC_970_NAP=y
# CONFIG_PPC_INDIRECT_IO is not set
# CONFIG_GENERIC_IOMAP is not set
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
#
# CPU Frequency drivers
#
CONFIG_CPU_FREQ_PMAC64=y
# CONFIG_CPM2 is not set
#
# Kernel options
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
# CONFIG_PREEMPT_BKL is not set
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_IOMMU_VMERGE=y
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPARSEMEM_EXTREME=y
#
# Memory hotplug is currently incompatible with Software Suspend
#
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
# CONFIG_PPC_HAS_HASH_64K is not set
# CONFIG_PPC_64K_PAGES is not set
CONFIG_SCHED_SMT=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_PM=y
CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
CONFIG_SECCOMP=y
# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_SYSCALL=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_XFRM_SUB_POLICY=y
CONFIG_XFRM_MIGRATE=y
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_ASK_IP_FIB_HASH=y
# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_VERBOSE=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
CONFIG_INET_IPCOMP=m
CONFIG_INET_XFRM_TUNNEL=m
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m
CONFIG_TCP_CONG_YEAH=m
CONFIG_TCP_CONG_ILLINOIS=m
# CONFIG_DEFAULT_BIC is not set
# CONFIG_DEFAULT_CUBIC is not set
# CONFIG_DEFAULT_HTCP is not set
# CONFIG_DEFAULT_VEGAS is not set
# CONFIG_DEFAULT_WESTWOOD is not set
CONFIG_DEFAULT_RENO=y
CONFIG_DEFAULT_TCP_CONG="reno"
CONFIG_TCP_MD5SIG=y
# CONFIG_IP_VS is not set
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_IPV6_ROUTER_PREF=y
CONFIG_IPV6_ROUTE_INFO=y
CONFIG_IPV6_OPTIMISTIC_DAD=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_IPV6_MIP6=m
CONFIG_INET6_XFRM_TUNNEL=m
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_IPV6_SIT=m
CONFIG_IPV6_TUNNEL=m
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
CONFIG_NETLABEL=y
CONFIG_NETWORK_SECMARK=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_BRIDGE_NETFILTER=y
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_SECMARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
CONFIG_NF_CT_PROTO_UDPLITE=m
CONFIG_NF_CONNTRACK_AMANDA=m
CONFIG_NF_CONNTRACK_FTP=m
CONFIG_NF_CONNTRACK_H323=m
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_SECMARK=m
CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_POLICY=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
CONFIG_NETFILTER_XT_MATCH_SCTP=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_U32=m
CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
#
# IP: Netfilter Configuration
#
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_AH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
CONFIG_NF_NAT_SNMP_BASIC=m
CONFIG_NF_NAT_PROTO_GRE=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
CONFIG_NF_NAT_AMANDA=m
CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
CONFIG_NF_CONNTRACK_IPV6=m
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AH=m
CONFIG_IP6_NF_MATCH_MH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_TARGET_REJECT=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m
#
# Bridge: Netfilter Configuration
#
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_ULOG=m
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y
#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID2=m
# CONFIG_IP_DCCP_CCID2_DEBUG is not set
CONFIG_IP_DCCP_CCID3=m
CONFIG_IP_DCCP_TFRC_LIB=m
# CONFIG_IP_DCCP_CCID3_DEBUG is not set
CONFIG_IP_DCCP_CCID3_RTO=100
#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
CONFIG_SCTP_HMAC_NONE=y
# CONFIG_SCTP_HMAC_SHA1 is not set
# CONFIG_SCTP_HMAC_MD5 is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_BRIDGE=m
CONFIG_VLAN_8021Q=m
# CONFIG_DECNET is not set
CONFIG_LLC=y
CONFIG_LLC2=m
CONFIG_IPX=m
CONFIG_IPX_INTERN=y
CONFIG_ATALK=m
CONFIG_DEV_APPLETALK=m
CONFIG_IPDDP=m
CONFIG_IPDDP_ENCAP=y
CONFIG_IPDDP_DECAP=y
CONFIG_X25=m
CONFIG_LAPB=m
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_FIFO=y
#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RR=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_INGRESS=m
#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_CLS_U32_PERF=y
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=y
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
CONFIG_NET_CLS_POLICE=y
CONFIG_NET_CLS_IND=y
#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
# CONFIG_BT_HCIUART is not set
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_BT_HCIBFUSB=m
CONFIG_BT_HCIVHCI=m
CONFIG_AF_RXRPC=m
# CONFIG_AF_RXRPC_DEBUG is not set
CONFIG_RXKAD=m
CONFIG_FIB_RULES=y
#
# Wireless
#
CONFIG_CFG80211=m
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
CONFIG_MAC80211_LEDS=y
CONFIG_MAC80211_DEBUGFS=y
CONFIG_MAC80211_DEBUG=y
CONFIG_MAC80211_VERBOSE_DEBUG=y
CONFIG_MAC80211_LOWTX_FRAME_DUMP=y
CONFIG_TKIP_DEBUG=y
CONFIG_MAC80211_DEBUG_COUNTERS=y
# CONFIG_MAC80211_IBSS_DEBUG is not set
CONFIG_MAC80211_VERBOSE_PS_DEBUG=y
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
CONFIG_NET_9P=m
# CONFIG_NET_9P_DEBUG is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
CONFIG_OF_DEVICE=y
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y
CONFIG_PARPORT_NOT_PC=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=123456
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y
CONFIG_ATA_OVER_ETH=m
CONFIG_MISC_DEVICES=y
CONFIG_PHANTOM=m
CONFIG_EEPROM_93CX6=m
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_IDE_TASK_IOCTL=y
CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_IDEDMA_FORCED=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=m
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=m
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
CONFIG_SCSI_SAS_ATA=y
CONFIG_SCSI_SAS_LIBSAS_DEBUG=y
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
CONFIG_SCSI_DEBUG=m
CONFIG_SCSI_SRP=m
CONFIG_ATA=m
# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_SVW=m
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_RAID5_RESHAPE=y
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
CONFIG_BLK_DEV_DM=m
# CONFIG_DM_DEBUG is not set
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
CONFIG_DM_MULTIPATH_RDAC=m
CONFIG_DM_DELAY=m
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
CONFIG_FIREWIRE=m
CONFIG_FIREWIRE_OHCI=m
CONFIG_FIREWIRE_SBP2=m
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
#
# Controllers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB_PMU=y
CONFIG_ADB_PMU_LED=y
CONFIG_ADB_PMU_LED_IDE=y
CONFIG_PMAC_SMU=y
CONFIG_MAC_EMUMOUSEBTN=y
CONFIG_THERM_PM72=y
CONFIG_WINDFARM=y
CONFIG_WINDFARM_PM81=y
CONFIG_WINDFARM_PM91=y
CONFIG_WINDFARM_PM112=y
# CONFIG_PMAC_RACKMETER is not set
CONFIG_NETDEVICES=y
CONFIG_NETDEVICES_MULTIQUEUE=y
CONFIG_IFB=m
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
# CONFIG_ARCNET is not set
CONFIG_PHYLIB=m
#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
CONFIG_ICPLUS_PHY=m
CONFIG_FIXED_PHY=m
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
CONFIG_SUNGEM=m
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=m
CONFIG_TULIP_MWI=y
CONFIG_TULIP_MMIO=y
CONFIG_TULIP_NAPI=y
CONFIG_TULIP_NAPI_HW_MITIGATION=y
CONFIG_DE4X5=m
CONFIG_WINBOND_840=m
CONFIG_DM9102=m
CONFIG_ULI526X=m
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_PCNET32_NAPI=y
CONFIG_AMD8111_ETH=m
CONFIG_AMD8111E_NAPI=y
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
CONFIG_E100=m
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_NET_POCKET is not set
CONFIG_NETDEV_1000=y
CONFIG_ACENIC=m
CONFIG_ACENIC_OMIT_TIGON_I=y
# CONFIG_DL2K is not set
CONFIG_E1000=m
CONFIG_E1000_NAPI=y
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
CONFIG_R8169_NAPI=y
CONFIG_R8169_VLAN=y
CONFIG_SIS190=m
# CONFIG_SKGE is not set
CONFIG_SKY2=m
# CONFIG_SKY2_DEBUG is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=m
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
CONFIG_CHELSIO_T1=m
CONFIG_CHELSIO_T1_1G=y
CONFIG_CHELSIO_T1_NAPI=y
CONFIG_CHELSIO_T3=m
CONFIG_IXGB=m
CONFIG_IXGB_NAPI=y
CONFIG_S2IO=m
CONFIG_S2IO_NAPI=y
CONFIG_MYRI10GE=m
CONFIG_NETXEN_NIC=m
# CONFIG_PASEMI_MAC is not set
# CONFIG_MLX4_CORE is not set
CONFIG_TR=y
CONFIG_IBMOL=m
# CONFIG_3C359 is not set
# CONFIG_TMS380TR is not set
#
# Wireless LAN
#
CONFIG_WLAN_PRE80211=y
# CONFIG_STRIP is not set
CONFIG_WLAN_80211=y
CONFIG_IPW2100=m
CONFIG_IPW2100_MONITOR=y
# CONFIG_IPW2100_DEBUG is not set
CONFIG_IPW2200=m
CONFIG_IPW2200_MONITOR=y
CONFIG_IPW2200_RADIOTAP=y
CONFIG_IPW2200_PROMISCUOUS=y
CONFIG_IPW2200_QOS=y
# CONFIG_IPW2200_DEBUG is not set
CONFIG_LIBERTAS=m
CONFIG_LIBERTAS_USB=m
# CONFIG_LIBERTAS_DEBUG is not set
CONFIG_AIRO=m
CONFIG_HERMES=m
CONFIG_APPLE_AIRPORT=m
CONFIG_PLX_HERMES=m
CONFIG_TMD_HERMES=m
CONFIG_NORTEL_HERMES=m
CONFIG_PCI_HERMES=m
CONFIG_ATMEL=m
CONFIG_PCI_ATMEL=m
CONFIG_PRISM54=m
CONFIG_USB_ZD1201=m
CONFIG_RTL8187=m
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
CONFIG_HOSTAP_FIRMWARE_NVRAM=y
CONFIG_HOSTAP_PLX=m
CONFIG_HOSTAP_PCI=m
CONFIG_BCM43XX=m
CONFIG_BCM43XX_DEBUG=y
CONFIG_BCM43XX_DMA=y
CONFIG_BCM43XX_PIO=y
CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
# CONFIG_BCM43XX_DMA_MODE is not set
# CONFIG_BCM43XX_PIO_MODE is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set
#
# USB Network Adapters
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET_MII=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_NET1080=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_USB_NET_ZAURUS=m
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPP_MPPE=m
CONFIG_PPPOE=m
CONFIG_PPPOL2TP=m
# CONFIG_SLIP is not set
CONFIG_SLHC=m
CONFIG_NET_FC=y
CONFIG_SHAPER=m
CONFIG_NETCONSOLE=m
CONFIG_NETPOLL=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_POLLDEV=m
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
CONFIG_INPUT_TSDEV=m
CONFIG_INPUT_TSDEV_SCREEN_X=240
CONFIG_INPUT_TSDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_EVBUG=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
CONFIG_MOUSE_APPLETOUCH=m
# CONFIG_MOUSE_VSXXXAA is not set
CONFIG_INPUT_JOYSTICK=y
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GRIP_MP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
CONFIG_JOYSTICK_IFORCE=m
CONFIG_JOYSTICK_IFORCE_USB=y
CONFIG_JOYSTICK_IFORCE_232=y
CONFIG_JOYSTICK_WARRIOR=m
CONFIG_JOYSTICK_MAGELLAN=m
CONFIG_JOYSTICK_SPACEORB=m
CONFIG_JOYSTICK_SPACEBALL=m
CONFIG_JOYSTICK_STINGER=m
CONFIG_JOYSTICK_TWIDJOY=m
# CONFIG_JOYSTICK_DB9 is not set
# CONFIG_JOYSTICK_GAMECON is not set
# CONFIG_JOYSTICK_TURBOGRAFX is not set
CONFIG_JOYSTICK_JOYDUMP=m
# CONFIG_JOYSTICK_XPAD is not set
CONFIG_INPUT_TABLET=y
CONFIG_TABLET_USB_ACECAD=m
CONFIG_TABLET_USB_AIPTEK=m
CONFIG_TABLET_USB_GTCO=m
CONFIG_TABLET_USB_KBTAB=m
CONFIG_TABLET_USB_WACOM=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
CONFIG_TOUCHSCREEN_FUJITSU=m
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
# CONFIG_TOUCHSCREEN_PENMOUNT is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_UCB1400 is not set
CONFIG_TOUCHSCREEN_USB_COMPOSITE=m
CONFIG_TOUCHSCREEN_USB_EGALAX=y
CONFIG_TOUCHSCREEN_USB_PANJIT=y
CONFIG_TOUCHSCREEN_USB_3M=y
CONFIG_TOUCHSCREEN_USB_ITM=y
CONFIG_TOUCHSCREEN_USB_ETURBO=y
CONFIG_TOUCHSCREEN_USB_GUNZE=y
CONFIG_TOUCHSCREEN_USB_DMC_TSC10=y
CONFIG_TOUCHSCREEN_USB_IRTOUCH=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_ATI_REMOTE=m
CONFIG_INPUT_ATI_REMOTE2=m
CONFIG_INPUT_KEYSPAN_REMOTE=m
CONFIG_INPUT_POWERMATE=m
CONFIG_INPUT_YEALINK=m
CONFIG_INPUT_UINPUT=m
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_RAW=m
CONFIG_GAMEPORT=m
# CONFIG_GAMEPORT_NS558 is not set
# CONFIG_GAMEPORT_L4 is not set
# CONFIG_GAMEPORT_EMU10K1 is not set
# CONFIG_GAMEPORT_FM801 is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_PMACZILOG=y
CONFIG_SERIAL_PMACZILOG_CONSOLE=y
CONFIG_SERIAL_JSM=m
CONFIG_SERIAL_OF_PLATFORM=m
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=64
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
#
# PCI-based Watchdog Cards
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set
#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_GEN_RTC=y
CONFIG_GEN_RTC_X=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_AGP=m
CONFIG_AGP_UNINORTH=m
CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=4096
# CONFIG_HANGCHECK_TIMER is not set
CONFIG_TCG_TPM=m
CONFIG_TCG_ATMEL=m
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_POWERMAC=y
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
CONFIG_SPI=y
CONFIG_SPI_DEBUG=y
CONFIG_SPI_MASTER=y
#
# SPI Master Controller Drivers
#
CONFIG_SPI_BITBANG=m
CONFIG_SPI_BUTTERFLY=m
CONFIG_SPI_LM70_LLP=m
#
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=m
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
CONFIG_VIDEO_V4L1=y
CONFIG_VIDEO_V4L1_COMPAT=y
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
CONFIG_VIDEO_TVAUDIO=m
CONFIG_VIDEO_TDA7432=m
CONFIG_VIDEO_TDA9875=m
CONFIG_VIDEO_MSP3400=m
CONFIG_VIDEO_WM8775=m
CONFIG_VIDEO_OV7670=m
CONFIG_VIDEO_SAA711X=m
CONFIG_VIDEO_TVP5150=m
CONFIG_VIDEO_CX25840=m
CONFIG_VIDEO_CX2341X=m
CONFIG_VIDEO_VIVI=m
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_BT848_DVB=y
CONFIG_VIDEO_SAA6588=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_CQCAM=m
# CONFIG_VIDEO_W9966 is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_CPIA2 is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_TUNER_TEA5761 is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set
# CONFIG_VIDEO_IVTV is not set
CONFIG_VIDEO_CAFE_CCIC=m
CONFIG_V4L_USB_DRIVERS=y
CONFIG_VIDEO_PVRUSB2=m
CONFIG_VIDEO_PVRUSB2_29XXX=y
CONFIG_VIDEO_PVRUSB2_24XXX=y
CONFIG_VIDEO_PVRUSB2_SYSFS=y
# CONFIG_VIDEO_PVRUSB2_DEBUGIFC is not set
CONFIG_VIDEO_EM28XX=m
CONFIG_VIDEO_USBVISION=m
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
CONFIG_USB_KONICAWC=m
CONFIG_USB_QUICKCAM_MESSENGER=m
CONFIG_USB_ET61X251=m
CONFIG_VIDEO_OVCAMCHIP=m
CONFIG_USB_W9968CF=m
CONFIG_USB_OV511=m
CONFIG_USB_SE401=m
CONFIG_USB_SN9C102=m
CONFIG_USB_STV680=m
CONFIG_USB_ZC0301=m
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set
CONFIG_USB_ZR364XX=m
CONFIG_RADIO_ADAPTERS=y
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
CONFIG_USB_DSBR=m
CONFIG_DVB_CORE=m
# CONFIG_DVB_CORE_ATTACH is not set
CONFIG_DVB_CAPTURE_DRIVERS=y
#
# Supported SAA7146 based PCI Adapters
#
CONFIG_DVB_AV7110=m
CONFIG_DVB_AV7110_OSD=y
CONFIG_DVB_BUDGET=m
CONFIG_DVB_BUDGET_CI=m
CONFIG_DVB_BUDGET_AV=m
CONFIG_DVB_BUDGET_PATCH=m
#
# Supported USB Adapters
#
CONFIG_DVB_USB=m
# CONFIG_DVB_USB_DEBUG is not set
CONFIG_DVB_USB_A800=m
CONFIG_DVB_USB_DIBUSB_MB=m
CONFIG_DVB_USB_DIBUSB_MB_FAULTY=y
CONFIG_DVB_USB_DIBUSB_MC=m
CONFIG_DVB_USB_DIB0700=m
CONFIG_DVB_USB_UMT_010=m
CONFIG_DVB_USB_CXUSB=m
CONFIG_DVB_USB_M920X=m
CONFIG_DVB_USB_GL861=m
CONFIG_DVB_USB_AU6610=m
CONFIG_DVB_USB_DIGITV=m
CONFIG_DVB_USB_VP7045=m
CONFIG_DVB_USB_VP702X=m
CONFIG_DVB_USB_GP8PSK=m
CONFIG_DVB_USB_NOVA_T_USB2=m
CONFIG_DVB_USB_TTUSB2=m
CONFIG_DVB_USB_DTT200U=m
CONFIG_DVB_USB_OPERA1=m
CONFIG_DVB_USB_AF9005=m
CONFIG_DVB_USB_AF9005_REMOTE=m
CONFIG_DVB_TTUSB_BUDGET=m
CONFIG_DVB_TTUSB_DEC=m
CONFIG_DVB_CINERGYT2=m
# CONFIG_DVB_CINERGYT2_TUNING is not set
#
# Supported FlexCopII (B2C2) Adapters
#
CONFIG_DVB_B2C2_FLEXCOP=m
CONFIG_DVB_B2C2_FLEXCOP_PCI=m
CONFIG_DVB_B2C2_FLEXCOP_USB=m
# CONFIG_DVB_B2C2_FLEXCOP_DEBUG is not set
#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m
#
# Supported Pluto2 Adapters
#
CONFIG_DVB_PLUTO2=m
#
# Supported DVB Frontends
#
#
# Customise DVB Frontends
#
# CONFIG_DVB_FE_CUSTOMISE is not set
#
# DVB-S (satellite) frontends
#
CONFIG_DVB_STV0299=m
CONFIG_DVB_CX24110=m
# CONFIG_DVB_CX24123 is not set
CONFIG_DVB_TDA8083=m
CONFIG_DVB_MT312=m
CONFIG_DVB_VES1X93=m
CONFIG_DVB_S5H1420=m
CONFIG_DVB_TDA10086=m
#
# DVB-T (terrestrial) frontends
#
CONFIG_DVB_SP8870=m
CONFIG_DVB_SP887X=m
CONFIG_DVB_CX22700=m
CONFIG_DVB_CX22702=m
CONFIG_DVB_L64781=m
CONFIG_DVB_TDA1004X=m
CONFIG_DVB_NXT6000=m
CONFIG_DVB_MT352=m
CONFIG_DVB_ZL10353=m
CONFIG_DVB_DIB3000MB=m
CONFIG_DVB_DIB3000MC=m
CONFIG_DVB_DIB7000M=m
CONFIG_DVB_DIB7000P=m
#
# DVB-C (cable) frontends
#
CONFIG_DVB_VES1820=m
CONFIG_DVB_TDA10021=m
CONFIG_DVB_TDA10023=m
CONFIG_DVB_STV0297=m
#
# ATSC (North American/Korean Terrestrial/Cable DTV) frontends
#
CONFIG_DVB_NXT200X=m
CONFIG_DVB_OR51211=m
# CONFIG_DVB_OR51132 is not set
CONFIG_DVB_BCM3510=m
CONFIG_DVB_LGDT330X=m
#
# Tuners/PLL support
#
CONFIG_DVB_PLL=m
CONFIG_DVB_TDA826X=m
CONFIG_DVB_TDA827X=m
CONFIG_DVB_TUNER_QT1010=m
CONFIG_DVB_TUNER_MT2060=m
#
# Miscellaneous devices
#
CONFIG_DVB_LNBP21=m
# CONFIG_DVB_ISL6421 is not set
CONFIG_DVB_TUA6100=m
CONFIG_VIDEO_SAA7146=m
CONFIG_VIDEO_SAA7146_VV=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR_I2C=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
CONFIG_DAB=y
CONFIG_USB_DABUSB=m
#
# Graphics support
#
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_BACKLIGHT_CLASS_DEVICE=y
#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=m
#
# Display hardware drivers
#
CONFIG_VGASTATE=y
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_SYS_FOPS is not set
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_OF=y
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
CONFIG_LOGO_LINUX_VGA16=y
# CONFIG_LOGO_LINUX_CLUT224 is not set
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_DYNAMIC_MINORS=y
CONFIG_SND_SUPPORT_OLD_API=y
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
# CONFIG_SND_DEBUG_DETECT is not set
# CONFIG_SND_PCM_XRUN_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_MTS64=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
CONFIG_SND_PORTMAN2X4=m
#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
# CONFIG_SND_DARLA20 is not set
# CONFIG_SND_GINA20 is not set
# CONFIG_SND_LAYLA20 is not set
# CONFIG_SND_DARLA24 is not set
# CONFIG_SND_GINA24 is not set
# CONFIG_SND_LAYLA24 is not set
# CONFIG_SND_MONA is not set
# CONFIG_SND_MIA is not set
# CONFIG_SND_ECHO3G is not set
# CONFIG_SND_INDIGO is not set
# CONFIG_SND_INDIGOIO is not set
# CONFIG_SND_INDIGODJ is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RIPTIDE is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
#
# ALSA PowerMac devices
#
CONFIG_SND_POWERMAC=m
CONFIG_SND_POWERMAC_AUTO_DRC=y
#
# ALSA PowerPC devices
#
#
# Apple Onboard Audio driver
#
CONFIG_SND_AOA=m
CONFIG_SND_AOA_FABRIC_LAYOUT=m
CONFIG_SND_AOA_ONYX=m
CONFIG_SND_AOA_TAS=m
CONFIG_SND_AOA_TOONIE=m
CONFIG_SND_AOA_SOUNDBUS=m
CONFIG_SND_AOA_SOUNDBUS_I2S=m
#
# USB devices
#
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_USX2Y=m
CONFIG_SND_USB_CAIAQ=m
CONFIG_SND_USB_CAIAQ_INPUT=y
#
# System on Chip audio support
#
# CONFIG_SND_SOC is not set
#
# SoC Audio support for SuperH
#
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT_POWERBOOK=y
CONFIG_HID_FF=y
CONFIG_HID_PID=y
CONFIG_LOGITECH_FF=y
CONFIG_PANTHERLORD_FF=y
CONFIG_THRUSTMASTER_FF=y
CONFIG_ZEROPLUS_FF=y
CONFIG_USB_HIDDEV=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
CONFIG_USB_OHCI_HCD_PCI=y
CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_U132_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_USBAT=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
CONFIG_USB_STORAGE_ALAUDA=y
CONFIG_USB_STORAGE_KARMA=y
# CONFIG_USB_LIBUSUAL is not set
#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
# CONFIG_USB_MON is not set
#
# USB port drivers
#
CONFIG_USB_USS720=m
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_AIRCABLE=m
CONFIG_USB_SERIAL_AIRPRIME=m
CONFIG_USB_SERIAL_ARK3116=m
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_CP2101=m
CONFIG_USB_SERIAL_CYPRESS_M8=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_FUNSOFT=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_GARMIN=m
CONFIG_USB_SERIAL_IPW=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
CONFIG_USB_SERIAL_KEYSPAN_MPR=y
CONFIG_USB_SERIAL_KEYSPAN_USA28=y
CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
CONFIG_USB_SERIAL_KEYSPAN_USA19=y
CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_MOS7720=m
CONFIG_USB_SERIAL_MOS7840=m
CONFIG_USB_SERIAL_NAVMAN=m
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_OTI6858=m
CONFIG_USB_SERIAL_HP4X=m
CONFIG_USB_SERIAL_SAFE=m
CONFIG_USB_SERIAL_SAFE_PADDED=y
CONFIG_USB_SERIAL_SIERRAWIRELESS=m
CONFIG_USB_SERIAL_TI=m
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OPTION=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_LEGOTOWER=m
CONFIG_USB_LCD=m
CONFIG_USB_BERRY_CHARGE=m
CONFIG_USB_LED=m
CONFIG_USB_CYPRESS_CY7C63=m
CONFIG_USB_CYTHERM=m
CONFIG_USB_PHIDGET=m
CONFIG_USB_PHIDGETKIT=m
CONFIG_USB_PHIDGETMOTORCONTROL=m
CONFIG_USB_PHIDGETSERVO=m
CONFIG_USB_IDMOUSE=m
CONFIG_USB_FTDI_ELAN=m
CONFIG_USB_APPLEDISPLAY=m
CONFIG_USB_SISUSBVGA=m
CONFIG_USB_SISUSBVGA_CON=y
CONFIG_USB_LD=m
CONFIG_USB_TRANCEVIBRATOR=m
CONFIG_USB_IOWARRIOR=m
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
#
# LED drivers
#
#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_IDE_DISK=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
# CONFIG_INFINIBAND is not set
CONFIG_EDAC=y
#
# Reporting subsystems
#
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_MM_EDAC=m
# CONFIG_RTC_CLASS is not set
#
# DMA Engine support
#
# CONFIG_DMA_ENGINE is not set
#
# DMA Clients
#
#
# DMA Devices
#
CONFIG_AUXDISPLAY=y
# CONFIG_KS0108 is not set
#
# Userspace I/O
#
CONFIG_UIO=m
CONFIG_UIO_CIF=m
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4DEV_FS=m
CONFIG_EXT4DEV_FS_XATTR=y
CONFIG_EXT4DEV_FS_POSIX_ACL=y
CONFIG_EXT4DEV_FS_SECURITY=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=m
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
CONFIG_GFS2_FS=m
CONFIG_GFS2_FS_LOCKING_NOLOCK=m
CONFIG_GFS2_FS_LOCKING_DLM=m
CONFIG_OCFS2_FS=m
# CONFIG_OCFS2_DEBUG_MASKLOG is not set
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_QUOTA=y
CONFIG_QFMT_V1=m
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m
CONFIG_GENERIC_ACL=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_ECRYPT_FS=m
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
CONFIG_EFS_FS=m
CONFIG_CRAMFS=m
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=m
CONFIG_UFS_FS_WRITE=y
# CONFIG_UFS_DEBUG is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
CONFIG_SUNRPC_BIND34=y
CONFIG_RPCSEC_GSS_KRB5=m
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
CONFIG_CIFS_STATS=y
# CONFIG_CIFS_STATS2 is not set
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
# CONFIG_CODA_FS is not set
CONFIG_AFS_FS=m
# CONFIG_AFS_DEBUG is not set
CONFIG_9P_FS=m
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
CONFIG_OSF_PARTITION=y
CONFIG_AMIGA_PARTITION=y
CONFIG_ATARI_PARTITION=y
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
CONFIG_SGI_PARTITION=y
CONFIG_ULTRIX_PARTITION=y
CONFIG_SUN_PARTITION=y
CONFIG_KARMA_PARTITION=y
CONFIG_EFI_PARTITION=y
CONFIG_SYSV68_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Distributed Lock Manager
#
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
# CONFIG_UCC_SLOW is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
# CONFIG_DETECT_SOFTLOCKUP is not set
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_DEBUGGER=y
CONFIG_XMON=y
# CONFIG_XMON_DEFAULT is not set
CONFIG_XMON_DISASSEMBLY=y
CONFIG_IRQSTACKS=y
# CONFIG_BOOTX_TEXT is not set
# CONFIG_PPC_EARLY_DEBUG is not set
#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
CONFIG_SECURITY_CAPABILITIES=y
CONFIG_SECURITY_ROOTPLUG=m
# CONFIG_SECURITY_SELINUX is not set
CONFIG_KEYS_COMPAT=y
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ABLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
CONFIG_CRYPTO_LRW=m
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_ANUBIS=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_TEST=m
CONFIG_CRYPTO_HW=y
^ permalink raw reply
* Re: [PATCH] [POWERPC] Invalid semicolon after if statement
From: Michael Ellerman @ 2007-08-16 23:08 UTC (permalink / raw)
To: Andreas Schwab; +Cc: Ilpo Järvinen, linuxppc-dev, paulus
In-Reply-To: <je7inva0w4.fsf@sykes.suse.de>
[-- Attachment #1: Type: text/plain, Size: 777 bytes --]
On Thu, 2007-08-16 at 18:40 +0200, Andreas Schwab wrote:
> Segher Boessenkool <segher@kernel.crashing.org> writes:
>
> >> Thanks to the frickin compiler for warning us, not.
> >
> > 4.3: "warning: suggest braces around empty body in an 'if' statement"
> >
> > 4.1: "warning: empty body in an if-statement"
> >
> > Your GCC is too old :-)
>
> This warning is only enabled by -Wextra. Only 4.3 has a separate option
> for it (-Wempty-body).
Oh good, so in 2011 we'll start getting a warning, sweet.
cheers
--
Michael Ellerman
OzLabs, IBM Australia Development Lab
wwweb: http://michael.ellerman.id.au
phone: +61 2 6212 1183 (tie line 70 21183)
We do not inherit the earth from our ancestors,
we borrow it from our children. - S.M.A.R.T Person
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply
* Re: [PATCH 2/2] [POWERPC] Add scaled time accounting
From: Michael Neuling @ 2007-08-16 23:48 UTC (permalink / raw)
To: balbir; +Cc: Andrew Morton, linuxppc-dev, Paul Mackerras, linux-kernel
In-Reply-To: <46C41C76.1020109@linux.vnet.ibm.com>
In message <46C41C76.1020109@linux.vnet.ibm.com> you wrote:
> Michael Neuling wrote:
> > This adds POWERPC specific hooks for scaled time accounting.
> >
> > POWER6 includes a SPURR register. The SPURR is based off the PURR
> > register but is scaled based on CPU frequency and issue rates. This
> > gives a more accurate account of the instructions used per task. The
> > PURR and timebase will be constant relative to the wall clock,
> > irrespective of the CPU frequency.
> >
> > This implementation reads the SPURR register in account_system_vtime
> > which is only call called on context witch and hard and soft irq entry
> > and exit. The percentage of user and system time is then estimated
> > using the ratio of these accounted by the PURR. If the SPURR is not
> > present, the PURR read.
> >
> > An earlier implementation of this patch read the SPURR whenever the
> > PURR was read, which included the system call entry and exit path.
> > Unfortunately this showed a performance regression on lmbench runs, so
> > was re-implemented.
> >
> > I've included the lmbench results here when run bare metal on POWER6.
> > 1st column is the unpatch results. 2nd column is the results using the
> > below patch and the 3rd is the % diff of these results from the base.
> > 4th and 5th columns are the results and % differnce from the base
> > using the older patch (SPURR read in syscall entry/exit path).
> >
> > Base Scaled-Acct SPURR-in-syscall
> > Result Result % diff Result % diff
> > Simple syscall: 0.3086 0.3086 0.0000 0.3452 11.8600
> > Simple read: 0.4591 0.4671 1.7425 0.5044 9.86713
> > Simple write: 0.4364 0.4366 0.0458 0.4731 8.40971
> > Simple stat: 2.0055 2.0295 1.1967 2.0669 3.06158
> > Simple fstat: 0.5962 0.5876 -1.442 0.6368 6.80979
> > Simple open/close: 3.1283 3.1009 -0.875 3.2088 2.57328
> > Select on 10 fd's: 0.8554 0.8457 -1.133 0.8667 1.32101
> > Select on 100 fd's: 3.5292 3.6329 2.9383 3.6664 3.88756
> > Select on 250 fd's: 7.9097 8.1881 3.5197 8.2242 3.97613
> > Select on 500 fd's: 15.2659 15.836 3.7357 15.873 3.97814
> > Select on 10 tcp fd's: 0.9576 0.9416 -1.670 0.9752 1.83792
> > Select on 100 tcp fd's: 7.248 7.2254 -0.311 7.2685 0.28283
> > Select on 250 tcp fd's: 17.7742 17.707 -0.375 17.749 -0.1406
> > Select on 500 tcp fd's: 35.4258 35.25 -0.496 35.286 -0.3929
> > Signal handler installation: 0.6131 0.6075 -0.913 0.647 5.52927
> > Signal handler overhead: 2.0919 2.1078 0.7600 2.1831 4.35967
> > Protection fault: 0.7345 0.7478 1.8107 0.8031 9.33968
> > Pipe latency: 33.006 16.398 -50.31 33.475 1.42368
> > AF_UNIX sock stream latency: 14.5093 30.910 113.03 30.715 111.692
> > Process fork+exit: 219.8 222.8 1.3648 229.37 4.35623
> > Process fork+execve: 876.14 873.28 -0.32 868.66 -0.8533
> > Process fork+/bin/sh -c: 2830 2876.5 1.6431 2958 4.52296
> > File /var/tmp/XXX write bw: 1193497 1195536 0.1708 118657 -0.5799
> > Pagefaults on /var/tmp/XXX: 3.1272 3.2117 2.7020 3.2521 3.99398
> >
> > Also, kernel compile times show no difference with this patch applied.
> >
> > Signed-off-by: Michael Neuling <mikey@neuling.org>
> >
> > ---
> >
> > arch/powerpc/kernel/asm-offsets.c | 1 +
> > arch/powerpc/kernel/time.c | 32 ++++++++++++++++++++++++++++++--
> > include/asm-powerpc/paca.h | 3 +++
> > 3 files changed, 34 insertions(+), 2 deletions(-)
> >
> > Index: linux-2.6-ozlabs/arch/powerpc/kernel/asm-offsets.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/arch/powerpc/kernel/asm-offsets.c
> > +++ linux-2.6-ozlabs/arch/powerpc/kernel/asm-offsets.c
> > @@ -141,6 +141,7 @@ int main(void)
> > DEFINE(PACALPPACAPTR, offsetof(struct paca_struct, lppaca_ptr));
> > DEFINE(PACAHWCPUID, offsetof(struct paca_struct, hw_cpu_id));
> > DEFINE(PACA_STARTPURR, offsetof(struct paca_struct, startpurr));
> > + DEFINE(PACA_STARTSPURR, offsetof(struct paca_struct, startspurr));
> > DEFINE(PACA_USER_TIME, offsetof(struct paca_struct, user_time));
> > DEFINE(PACA_SYSTEM_TIME, offsetof(struct paca_struct, system_time));
> > DEFINE(PACA_SLBSHADOWPTR, offsetof(struct paca_struct, slb_shadow_ptr))
;
> > Index: linux-2.6-ozlabs/arch/powerpc/kernel/time.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/arch/powerpc/kernel/time.c
> > +++ linux-2.6-ozlabs/arch/powerpc/kernel/time.c
> > @@ -168,23 +168,44 @@ static u64 read_purr(void)
> > }
> >
> > /*
> > + * Read the SPURR on systems that have it, otherwise the purr
> > + */
> > +static u64 read_spurr(void)
> > +{
> > + if (cpu_has_feature(CPU_FTR_SPURR))
> > + return mfspr(SPRN_SPURR);
> > + return read_purr();
> > +}
> > +
> > +/*
> > * Account time for a transition between system, hard irq
> > * or soft irq state.
> > */
> > void account_system_vtime(struct task_struct *tsk)
> > {
> > - u64 now, delta;
> > + u64 now, nowscaled, delta, deltascaled;
> > unsigned long flags;
> >
> > local_irq_save(flags);
> > now = read_purr();
> > delta = now - get_paca()->startpurr;
> > get_paca()->startpurr = now;
> > + nowscaled = read_spurr();
> > + deltascaled = nowscaled - get_paca()->startspurr;
> > + get_paca()->startspurr = nowscaled;
> > if (!in_interrupt()) {
> > + /* deltascaled includes both user and system time.
> > + * Hence scale it based on the purr ratio to estimate
> > + * the system time */
> > + deltascaled = deltascaled * get_paca()->system_time /
> > + (get_paca()->system_time + get_paca()->user_time);
> > delta += get_paca()->system_time;
> > get_paca()->system_time = 0;
> > }
> > account_system_time(tsk, 0, delta);
> > + get_paca()->purrdelta = delta;
> > + account_system_time_scaled(tsk, deltascaled);
> > + get_paca()->spurrdelta = deltascaled;
> > local_irq_restore(flags);
> > }
> >
> > @@ -196,11 +217,17 @@ void account_system_vtime(struct task_st
> > */
> > void account_process_vtime(struct task_struct *tsk)
> > {
> > - cputime_t utime;
> > + cputime_t utime, utimescaled;
> >
> > utime = get_paca()->user_time;
> > get_paca()->user_time = 0;
> > account_user_time(tsk, utime);
> > +
> > + /* Estimate the scaled utime by scaling the real utime based
> > + * on the last spurr to purr ratio */
> > + utimescaled = utime * get_paca()->spurrdelta / get_paca()->purrdelta;
>
>
> The assumption is account_process_vtime() is always called after
> account_system_vtime(), is my understanding correct?
Yes, we use last spurr/purr ratio grabbed in account_system_vtime to
scale utime appropriately.
Mikey
^ permalink raw reply
* Re: [PATCH 1/2] Add scaled time to taskstats based process accounting
From: Michael Neuling @ 2007-08-17 0:23 UTC (permalink / raw)
To: balbir; +Cc: Andrew Morton, linuxppc-dev, Paul Mackerras, linux-kernel
In-Reply-To: <46C3FC41.4000609@linux.vnet.ibm.com>
In message <46C3FC41.4000609@linux.vnet.ibm.com> you wrote:
> Hi, Michael,
>
> Thanks for doing this, this is really useful.
>
> Michael Neuling wrote:
> > This adds two items to the taststats struct to account for user and
> > system time based on scaling the CPU frequency and instruction issue
> > rates.
> >
> > Adds account_(user|system)_time_scaled callbacks which architectures
> > can use to account for time using this mechanism.
> >
> > Signed-off-by: Michael Neuling <mikey@neuling.org>
> >
> > ---
> >
> > include/linux/kernel_stat.h | 2 ++
> > include/linux/sched.h | 2 +-
> > include/linux/taskstats.h | 6 +++++-
> > kernel/fork.c | 2 ++
> > kernel/sched.c | 21 +++++++++++++++++++++
> > kernel/timer.c | 7 +++++--
> > kernel/tsacct.c | 4 ++++
> > 7 files changed, 40 insertions(+), 4 deletions(-)
> >
> > Index: linux-2.6-ozlabs/include/linux/kernel_stat.h
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/include/linux/kernel_stat.h
> > +++ linux-2.6-ozlabs/include/linux/kernel_stat.h
> > @@ -52,7 +52,9 @@ static inline int kstat_irqs(int irq)
> > }
> >
> > extern void account_user_time(struct task_struct *, cputime_t);
> > +extern void account_user_time_scaled(struct task_struct *, cputime_t);
> > extern void account_system_time(struct task_struct *, int, cputime_t);
> > +extern void account_system_time_scaled(struct task_struct *, cputime_t);
> > extern void account_steal_time(struct task_struct *, cputime_t);
> >
> > #endif /* _LINUX_KERNEL_STAT_H */
> > Index: linux-2.6-ozlabs/include/linux/sched.h
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/include/linux/sched.h
> > +++ linux-2.6-ozlabs/include/linux/sched.h
> > @@ -1020,7 +1020,7 @@ struct task_struct {
> > int __user *clear_child_tid; /* CLONE_CHILD_CLEARTID */
> >
> > unsigned int rt_priority;
> > - cputime_t utime, stime;
> > + cputime_t utime, stime, utimescaled, stimescaled;
> > unsigned long nvcsw, nivcsw; /* context switch counts */
> > struct timespec start_time; /* monotonic time */
> > struct timespec real_start_time; /* boot based time */
> > Index: linux-2.6-ozlabs/include/linux/taskstats.h
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/include/linux/taskstats.h
> > +++ linux-2.6-ozlabs/include/linux/taskstats.h
> > @@ -31,7 +31,7 @@
> > */
> >
> >
> > -#define TASKSTATS_VERSION 5
> > +#define TASKSTATS_VERSION 6
> > #define TS_COMM_LEN 32 /* should be >= TASK_COMM_LEN
> > * in linux/sched.h */
> >
> > @@ -142,6 +142,10 @@ struct taskstats {
> > __u64 write_char; /* bytes written */
> > __u64 read_syscalls; /* read syscalls */
> > __u64 write_syscalls; /* write syscalls */
> > +
> > + /* time accounting for SMT machines */
> > + __u64 ac_utimescaled; /* utime scaled on frequency etc */
> > + __u64 ac_stimescaled; /* stime scaled on frequency etc */
> > /* Extended accounting fields end */
> >
>
> I'd also request for you to add a cpu_scaled_run_real_total for use
> by delay accounting. cpu_scaled_run_real_total should be similar in
> functionality to cpu_run_real_total.
Will do. Should I add cpu_scaled_run_real_total to the end of the
struct taskstat, or next to cpu_run_real_total?
>
> > #define TASKSTATS_HAS_IO_ACCOUNTING
> > Index: linux-2.6-ozlabs/kernel/fork.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/kernel/fork.c
> > +++ linux-2.6-ozlabs/kernel/fork.c
> > @@ -1045,6 +1045,8 @@ static struct task_struct *copy_process(
> >
> > p->utime = cputime_zero;
> > p->stime = cputime_zero;
> > + p->utimescaled = cputime_zero;
> > + p->stimescaled = cputime_zero;
> >
> > #ifdef CONFIG_TASK_XACCT
> > p->rchar = 0; /* I/O counter: bytes read */
> > Index: linux-2.6-ozlabs/kernel/sched.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/kernel/sched.c
> > +++ linux-2.6-ozlabs/kernel/sched.c
> > @@ -3249,6 +3249,16 @@ void account_user_time(struct task_struc
> > }
> >
> > /*
> > + * Account scaled user cpu time to a process.
> > + * @p: the process that the cpu time gets accounted to
> > + * @cputime: the cpu time spent in user space since the last update
> > + */
> > +void account_user_time_scaled(struct task_struct *p, cputime_t cputime)
> > +{
> > + p->utimescaled = cputime_add(p->utimescaled, cputime);
> > +}
> > +
> > +/*
> > * Account system cpu time to a process.
> > * @p: the process that the cpu time gets accounted to
> > * @hardirq_offset: the offset to subtract from hardirq_count()
> > @@ -3280,6 +3290,17 @@ void account_system_time(struct task_str
> > }
> >
> > /*
> > + * Account scaled system cpu time to a process.
> > + * @p: the process that the cpu time gets accounted to
> > + * @hardirq_offset: the offset to subtract from hardirq_count()
> > + * @cputime: the cpu time spent in kernel space since the last update
> > + */
> > +void account_system_time_scaled(struct task_struct *p, cputime_t cputime)
> > +{
> > + p->stimescaled = cputime_add(p->stimescaled, cputime);
> > +}
> > +
> > +/*
> > * Account for involuntary wait time.
> > * @p: the process from which the cpu time has been stolen
> > * @steal: the cpu time spent in involuntary wait
> > Index: linux-2.6-ozlabs/kernel/timer.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/kernel/timer.c
> > +++ linux-2.6-ozlabs/kernel/timer.c
> > @@ -826,10 +826,13 @@ void update_process_times(int user_tick)
> > int cpu = smp_processor_id();
> >
> > /* Note: this timer irq context must be accounted for as well. */
> > - if (user_tick)
> > + if (user_tick) {
> > account_user_time(p, jiffies_to_cputime(1));
> > - else
> > + account_user_time_scaled(p, jiffies_to_cputime(1));
> > + } else {
> > account_system_time(p, HARDIRQ_OFFSET, jiffies_to_cputime(1));
> > + account_system_time_scaled(p, jiffies_to_cputime(1));
> > + }
>
> I am a little confused here, scaled accounting and regular accounting
> go hand in hand?
We need to account for scaled and normal time in this generic code.
All other calls to account_(user|system)_time are in arch code.
>
> > run_local_timers();
> > if (rcu_pending(cpu))
> > rcu_check_callbacks(cpu, user_tick);
> > Index: linux-2.6-ozlabs/kernel/tsacct.c
> > ===================================================================
> > --- linux-2.6-ozlabs.orig/kernel/tsacct.c
> > +++ linux-2.6-ozlabs/kernel/tsacct.c
> > @@ -62,6 +62,10 @@ void bacct_add_tsk(struct taskstats *sta
> > rcu_read_unlock();
> > stats->ac_utime = cputime_to_msecs(tsk->utime) * USEC_PER_MSEC;
> > stats->ac_stime = cputime_to_msecs(tsk->stime) * USEC_PER_MSEC;
> > + stats->ac_utimescaled =
> > + cputime_to_msecs(tsk->utimescaled) * USEC_PER_MSEC;
> > + stats->ac_stimescaled =
> > + cputime_to_msecs(tsk->stimescaled) * USEC_PER_MSEC;
> > stats->ac_minflt = tsk->min_flt;
> > stats->ac_majflt = tsk->maj_flt;
> >
>
>
> --
> Warm Regards,
> Balbir Singh
> Linux Technology Center
> IBM, ISTL
>
^ permalink raw reply
* Re: [PATCH] powerpc: Implement atomic{, 64}_{read, write}() without volatile
From: Paul Mackerras @ 2007-08-17 0:43 UTC (permalink / raw)
To: Segher Boessenkool; +Cc: linux-arch, linuxppc-dev, linux-kernel
In-Reply-To: <11867913303733-git-send-email-segher@kernel.crashing.org>
Segher Boessenkool writes:
> Instead, use asm() like all other atomic operations already do.
> +static __inline__ long atomic64_read(const atomic_t *v)
> +static __inline__ void atomic64_set(atomic_t *v, long i)
s/atomic_t/atomic64_t/ in both lines. I've edited my copy of the patch.
Paul.
^ permalink raw reply
* Please pull powerpc.git merge branch
From: Paul Mackerras @ 2007-08-17 0:51 UTC (permalink / raw)
To: torvalds; +Cc: linuxppc-dev
Linus,
Please do
git pull \
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc.git merge
I have added one more patch from Ilpo J=E4rvinen since the last pull
request, removing an incorrect semicolon.
Paul.
arch/powerpc/boot/flatdevtree.c | 18 ------------------
arch/powerpc/kernel/Makefile | 1 +
arch/powerpc/kernel/misc=5F32.S | 12 +++++++++++-
arch/powerpc/mm/hash=5Futils=5F64.c | 2 +-
arch/powerpc/platforms/cell/spu=5Fsyscalls.c | 1 +
arch/powerpc/platforms/ps3/device-init.c | 2 +-
arch/ppc/kernel/misc.S | 12 +++++++++++-
7 files changed, 26 insertions(+), 22 deletions(-)
commit 2b02d13996fe28478e45605de9bd8bdca25718de
Author: Ilpo J=C3=A4rvinen <ilpo.jarvinen@helsinki.fi>
Date: Thu Aug 16 08:03:35 2007 +1000
[POWERPC] Fix invalid semicolon after if statement
=20
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
=20
Signed-off-by: Ilpo J=C3=A4rvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 2de69124e86682c3427adb4136e097854841e467
Author: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Date: Wed Aug 15 02:30:13 2007 +1000
[POWERPC] ps3: Fix no storage devices found
=20
Fix probing of PS3 storage devices: in the success case, we should =
set
`error' to zero, not `result'.
=20
Without this patch no storage devices are found.
=20
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 55a910a81d0c3014abc20b9efa73c595b3e68339
Author: Roland McGrath <roland@redhat.com>
Date: Sat Aug 11 09:03:11 2007 +1000
[POWERPC] Fix for assembler -g
=20
ppc64 does the unusual thing of using #include on a compiler-genera=
ted
assembly file (lparmap.s) from an assembly source file (head=5F64.S=
).
This runs afoul of my recent patch to pass -gdwarf2 to the assemble=
r
under CONFIG=5FDEBUG=5FINFO. This patch avoids the problem by disa=
bling
DWARF generation (-g0) when producing lparmap.s.
=20
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit aa1cf632bd6f998cb4567ccf1a9d2e5daaa9fb44
Author: David Gibson <david@gibson.dropbear.id.au>
Date: Tue Aug 7 14:20:50 2007 +1000
[POWERPC] Fix small race in 44x tlbie function
=20
The 440 family of processors don't have a tlbie instruction. So, w=
e
implement TLB invalidates by explicitly searching the TLB with tlbs=
x.,
then clobbering the relevant entry, if any. Unfortunately the PID =
for
the search needs to be stored in the MMUCR register, which is also
used by the TLB miss handler. Interrupts were enabled in =5Ftlbie(=
), so
an interrupt between loading the MMUCR and the tlbsx could cause
incorrect search results, and thus a failure to invalide TLB entrie=
s
which needed to be invalidated.
=20
This fixes the problem in both arch/ppc and arch/powerpc by inhibit=
ing
interrupts (even critical and debug interrupts) across the relevant=
instructions.
=20
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit fa6b769a8e981afea869285982640168f76774df
Author: Becky Bruce <becky.bruce@freescale.com>
Date: Sat May 12 03:49:39 2007 +1000
[POWERPC] Remove unused code causing a compile warning
=20
AFAICT, nobody is using ft=5Fordered(), and it causes a build warni=
ng
to be generated. This patch cleans that up by removing the functio=
n
and the commented-out code that calls it.
=20
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit ad941fe4b6b83999863f49dfba7b3d2cebc4ced5
Author: Jeremy Kerr <jk@ozlabs.org>
Date: Mon Aug 13 13:22:44 2007 +1000
[POWERPC] cell: Fix errno for modular spufs=5Fcreate with invalid n=
eighbour
=20
At present, spu=5Fcreate with an invalid neighbo(u)r will return -E=
NOSYS,
not -EBADF, but only when spufs.o is built as a module.
=20
This change adds the appropriate errno, making the behaviour the sa=
me
as the built-in case.
=20
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
^ permalink raw reply
* [PATCH 1/2] Add scaled time to taskstats based process accounting
From: Michael Neuling @ 2007-08-17 1:09 UTC (permalink / raw)
To: Paul Mackerras, Andrew Morton; +Cc: linuxppc-dev, linux-kernel, balbir
In-Reply-To: <46C3FC41.4000609@linux.vnet.ibm.com>
This adds items to the taststats struct to account for user and system
time based on scaling the CPU frequency and instruction issue rates.
Adds account_(user|system)_time_scaled callbacks which architectures
can use to account for time using this mechanism.
Signed-off-by: Michael Neuling <mikey@neuling.org>
---
Updated based on comments from Balbir
include/linux/kernel_stat.h | 2 ++
include/linux/sched.h | 2 +-
include/linux/taskstats.h | 11 +++++++++--
kernel/delayacct.c | 6 ++++++
kernel/fork.c | 2 ++
kernel/sched.c | 21 +++++++++++++++++++++
kernel/timer.c | 7 +++++--
kernel/tsacct.c | 4 ++++
8 files changed, 50 insertions(+), 5 deletions(-)
Index: linux-2.6-ozlabs/include/linux/kernel_stat.h
===================================================================
--- linux-2.6-ozlabs.orig/include/linux/kernel_stat.h
+++ linux-2.6-ozlabs/include/linux/kernel_stat.h
@@ -52,7 +52,9 @@ static inline int kstat_irqs(int irq)
}
extern void account_user_time(struct task_struct *, cputime_t);
+extern void account_user_time_scaled(struct task_struct *, cputime_t);
extern void account_system_time(struct task_struct *, int, cputime_t);
+extern void account_system_time_scaled(struct task_struct *, cputime_t);
extern void account_steal_time(struct task_struct *, cputime_t);
#endif /* _LINUX_KERNEL_STAT_H */
Index: linux-2.6-ozlabs/include/linux/sched.h
===================================================================
--- linux-2.6-ozlabs.orig/include/linux/sched.h
+++ linux-2.6-ozlabs/include/linux/sched.h
@@ -1020,7 +1020,7 @@ struct task_struct {
int __user *clear_child_tid; /* CLONE_CHILD_CLEARTID */
unsigned int rt_priority;
- cputime_t utime, stime;
+ cputime_t utime, stime, utimescaled, stimescaled;
unsigned long nvcsw, nivcsw; /* context switch counts */
struct timespec start_time; /* monotonic time */
struct timespec real_start_time; /* boot based time */
Index: linux-2.6-ozlabs/include/linux/taskstats.h
===================================================================
--- linux-2.6-ozlabs.orig/include/linux/taskstats.h
+++ linux-2.6-ozlabs/include/linux/taskstats.h
@@ -31,7 +31,7 @@
*/
-#define TASKSTATS_VERSION 5
+#define TASKSTATS_VERSION 6
#define TS_COMM_LEN 32 /* should be >= TASK_COMM_LEN
* in linux/sched.h */
@@ -85,9 +85,12 @@ struct taskstats {
* On some architectures, value will adjust for cpu time stolen
* from the kernel in involuntary waits due to virtualization.
* Value is cumulative, in nanoseconds, without a corresponding count
- * and wraps around to zero silently on overflow
+ * and wraps around to zero silently on overflow. The
+ * _scaled_ version accounts for cpus which can scale the
+ * number of instructions executed each cycle.
*/
__u64 cpu_run_real_total;
+ __u64 cpu_scaled_run_real_total;
/* cpu "virtual" running time
* Uses time intervals seen by the kernel i.e. no adjustment
@@ -142,6 +145,10 @@ struct taskstats {
__u64 write_char; /* bytes written */
__u64 read_syscalls; /* read syscalls */
__u64 write_syscalls; /* write syscalls */
+
+ /* time accounting for SMT machines */
+ __u64 ac_utimescaled; /* utime scaled on frequency etc */
+ __u64 ac_stimescaled; /* stime scaled on frequency etc */
/* Extended accounting fields end */
#define TASKSTATS_HAS_IO_ACCOUNTING
Index: linux-2.6-ozlabs/kernel/delayacct.c
===================================================================
--- linux-2.6-ozlabs.orig/kernel/delayacct.c
+++ linux-2.6-ozlabs/kernel/delayacct.c
@@ -115,6 +115,12 @@ int __delayacct_add_tsk(struct taskstats
tmp += timespec_to_ns(&ts);
d->cpu_run_real_total = (tmp < (s64)d->cpu_run_real_total) ? 0 : tmp;
+ tmp = (s64)d->cpu_scaled_run_real_total;
+ cputime_to_timespec(tsk->utimescaled + tsk->stimescaled, &ts);
+ tmp += timespec_to_ns(&ts);
+ d->cpu_scaled_run_real_total =
+ (tmp < (s64)d->cpu_scaled_run_real_total) ? 0 : tmp;
+
/*
* No locking available for sched_info (and too expensive to add one)
* Mitigate by taking snapshot of values
Index: linux-2.6-ozlabs/kernel/fork.c
===================================================================
--- linux-2.6-ozlabs.orig/kernel/fork.c
+++ linux-2.6-ozlabs/kernel/fork.c
@@ -1045,6 +1045,8 @@ static struct task_struct *copy_process(
p->utime = cputime_zero;
p->stime = cputime_zero;
+ p->utimescaled = cputime_zero;
+ p->stimescaled = cputime_zero;
#ifdef CONFIG_TASK_XACCT
p->rchar = 0; /* I/O counter: bytes read */
Index: linux-2.6-ozlabs/kernel/sched.c
===================================================================
--- linux-2.6-ozlabs.orig/kernel/sched.c
+++ linux-2.6-ozlabs/kernel/sched.c
@@ -3249,6 +3249,16 @@ void account_user_time(struct task_struc
}
/*
+ * Account scaled user cpu time to a process.
+ * @p: the process that the cpu time gets accounted to
+ * @cputime: the cpu time spent in user space since the last update
+ */
+void account_user_time_scaled(struct task_struct *p, cputime_t cputime)
+{
+ p->utimescaled = cputime_add(p->utimescaled, cputime);
+}
+
+/*
* Account system cpu time to a process.
* @p: the process that the cpu time gets accounted to
* @hardirq_offset: the offset to subtract from hardirq_count()
@@ -3280,6 +3290,17 @@ void account_system_time(struct task_str
}
/*
+ * Account scaled system cpu time to a process.
+ * @p: the process that the cpu time gets accounted to
+ * @hardirq_offset: the offset to subtract from hardirq_count()
+ * @cputime: the cpu time spent in kernel space since the last update
+ */
+void account_system_time_scaled(struct task_struct *p, cputime_t cputime)
+{
+ p->stimescaled = cputime_add(p->stimescaled, cputime);
+}
+
+/*
* Account for involuntary wait time.
* @p: the process from which the cpu time has been stolen
* @steal: the cpu time spent in involuntary wait
Index: linux-2.6-ozlabs/kernel/timer.c
===================================================================
--- linux-2.6-ozlabs.orig/kernel/timer.c
+++ linux-2.6-ozlabs/kernel/timer.c
@@ -826,10 +826,13 @@ void update_process_times(int user_tick)
int cpu = smp_processor_id();
/* Note: this timer irq context must be accounted for as well. */
- if (user_tick)
+ if (user_tick) {
account_user_time(p, jiffies_to_cputime(1));
- else
+ account_user_time_scaled(p, jiffies_to_cputime(1));
+ } else {
account_system_time(p, HARDIRQ_OFFSET, jiffies_to_cputime(1));
+ account_system_time_scaled(p, jiffies_to_cputime(1));
+ }
run_local_timers();
if (rcu_pending(cpu))
rcu_check_callbacks(cpu, user_tick);
Index: linux-2.6-ozlabs/kernel/tsacct.c
===================================================================
--- linux-2.6-ozlabs.orig/kernel/tsacct.c
+++ linux-2.6-ozlabs/kernel/tsacct.c
@@ -62,6 +62,10 @@ void bacct_add_tsk(struct taskstats *sta
rcu_read_unlock();
stats->ac_utime = cputime_to_msecs(tsk->utime) * USEC_PER_MSEC;
stats->ac_stime = cputime_to_msecs(tsk->stime) * USEC_PER_MSEC;
+ stats->ac_utimescaled =
+ cputime_to_msecs(tsk->utimescaled) * USEC_PER_MSEC;
+ stats->ac_stimescaled =
+ cputime_to_msecs(tsk->stimescaled) * USEC_PER_MSEC;
stats->ac_minflt = tsk->min_flt;
stats->ac_majflt = tsk->maj_flt;
^ permalink raw reply
* for-2.6.24 branch in powerpc.git created
From: Paul Mackerras @ 2007-08-17 2:13 UTC (permalink / raw)
To: linuxppc-dev
I have made a for-2.6.24 branch in powerpc.git and pushed the
following patches to it.
Paul.
Becky Bruce (1):
[POWERPC] Update lmb.h include protection to ASM_POWERPC
David Gibson (4):
[POWERPC] Fixes to allow use of Ebony's flash chips through physmap_of
[POWERPC] Fix setting of irq trigger type in UIC driver
[POWERPC] Fix irq flow handler for 4xx UIC
[POWERPC] Improve robustness of the UIC cascade handler
Gabriel C (1):
[POWERPC] Typo fixes interrrupt -> interrupt
Grant Likely (1):
[POWERPC] Only ignore arch/ppc/include, not arch/ppc/boot/include
Guennadi Liakhovetski (1):
[POWERPC] Fix i2c device string format
Ishizaki Kou (4):
[POWERPC] Fix celleb pci section warnings
[POWERPC] Fix celleb sio section warning
[POWERPC] Init markings for celleb
[POWERPC] Init markings for hvc_beat
Jesper Juhl (1):
[POWERPC] Clean out a bunch of duplicate includes
Jon Loeliger (3):
[POWERPC] 52xx: Remove unnecessary loops_per_jiffy initialization code
[POWERPC] 8xx: Remove unnecessary loops_per_jiffy initialization code
[POWERPC] embedded6xx: Remove unnecessary loops_per_jiffy initialization code
Linas Vepstas (10):
[POWERPC] EEH: Tweak printk message
[POWERPC] EEH: Fix PCI bridge handling bug
[POWERPC] EEH: Dump PCI bridge status on event
[POWERPC] pseries: Avoid excess rtas_token calls
[POWERPC] pseries: Use rtas_token instead of hand-rolled code
[POWERPC] pseries: Simplify rtasd initialization
[POWERPC] Remove nvram forward declarations
[POWERPC] pseries: Fix jumbled no_logging flag
[POWERPC] pseries: Eliminate global error_log_cnt variable
[POWERPC] pseries: Remove dead EEH video code
Mariusz Kozlowski (1):
[POWERPC] drivers/macintosh/therm_adt746x.c: kmalloc + memset conversion to kzalloc
Michael Buesch (1):
[POWERPC] via-pmu: Fix typo in printk
Murali Iyer (1):
[POWERPC] Export DCR symbols for modules
Nathan Lynch (14):
[POWERPC] Remove gratuitous reads from maple PCI config space methods
[POWERPC] rtas_pci_ops: Use named structure member initializers
[POWERPC] celleb_fake_pci_ops: Use named structure member initializers
[POWERPC] celleb_epci_ops: Use named structure member initializers
[POWERPC] maple pci_ops: Use named structure member initializers
[POWERPC] pa_pxp_ops: Use named structure member initializers
[POWERPC] powermac pci_ops: Use named structure member initializers
[POWERPC] null_pci_ops: Use named structure member initializers
[POWERPC] efika rtas_pci_ops: Use named structure member initializers
[POWERPC] chrp pci_ops: Use named structure member initializers
[POWERPC] indirect_pci_ops: Use named structure member initializers
[POWERPC] tsi108_direct_pci_ops: Use named structure member initializers
[POWERPC] Remove gratuitous reads from pasemi pci config space methods
[POWERPC] Remove gratuitous reads from powermac pci config space methods
Paul Mackerras (1):
[POWERPC] Handle alignment faults on new FP load/store instructions
Segher Boessenkool (2):
[POWERPC] Replace a few #defines with empty inline functions
[POWERPC] Implement atomic{, 64}_{read, write}() without volatile
Stephen Rothwell (10):
[POWERPC] Fix non HUGETLB_PAGE build warning
[POWERPC] Use of_get_property in ipmi code
[POWERPC] Remove get_property and device_is_compatible
[POWERPC] Tidy up CONFIG_PPC_MM_SLICES code
[POWERPC] Comment out a currently unused function
[POWERPC] Fix section mismatch in crash_dump.c
[POWERPC] Fix section mismatch in dart_iommu.c
[POWERPC] Fix section mismatches in udbg_adb.c
[POWERPC] Fix section mismatch in pasemi/iommu.c
[POWERPC] Remove some duplicate declarations from pmac.h
arch/powerpc/boot/dts/ebony.dts | 1
arch/powerpc/boot/ebony.c | 39 +++
arch/powerpc/configs/ebony_defconfig | 246 ++++++++++-----------
arch/powerpc/kernel/align.c | 57 ++++-
arch/powerpc/kernel/btext.c | 1
arch/powerpc/kernel/crash.c | 1
arch/powerpc/kernel/crash_dump.c | 2
arch/powerpc/kernel/iommu.c | 1
arch/powerpc/kernel/nvram_64.c | 23 --
arch/powerpc/kernel/pci_32.c | 4
arch/powerpc/kernel/prom.c | 1
arch/powerpc/kernel/rtas_pci.c | 4
arch/powerpc/kernel/time.c | 1
arch/powerpc/mm/hash_utils_64.c | 7 -
arch/powerpc/mm/hugetlbpage.c | 3
arch/powerpc/mm/init_32.c | 1
arch/powerpc/mm/mem.c | 1
arch/powerpc/mm/mmu_context_64.c | 11 -
arch/powerpc/mm/slice.c | 1
arch/powerpc/platforms/52xx/efika.c | 4
arch/powerpc/platforms/52xx/lite5200.c | 13 -
arch/powerpc/platforms/52xx/mpc52xx_pic.c | 1
arch/powerpc/platforms/8xx/mpc86xads_setup.c | 14 -
arch/powerpc/platforms/8xx/mpc885ads_setup.c | 14 -
arch/powerpc/platforms/celleb/pci.c | 16 +
arch/powerpc/platforms/celleb/scc_epci.c | 8 -
arch/powerpc/platforms/celleb/scc_sio.c | 8 -
arch/powerpc/platforms/celleb/setup.c | 4
arch/powerpc/platforms/chrp/pci.c | 8 -
arch/powerpc/platforms/chrp/setup.c | 1
arch/powerpc/platforms/chrp/smp.c | 1
arch/powerpc/platforms/embedded6xx/holly.c | 14 -
arch/powerpc/platforms/embedded6xx/linkstation.c | 2
arch/powerpc/platforms/embedded6xx/mpc7448_hpc2.c | 2
arch/powerpc/platforms/embedded6xx/prpmc2800.c | 7 -
arch/powerpc/platforms/iseries/it_lp_naca.h | 2
arch/powerpc/platforms/iseries/setup.c | 1
arch/powerpc/platforms/maple/pci.c | 21 +-
arch/powerpc/platforms/pasemi/iommu.c | 4
arch/powerpc/platforms/pasemi/pci.c | 7 -
arch/powerpc/platforms/powermac/low_i2c.c | 1
arch/powerpc/platforms/powermac/pci.c | 25 +-
arch/powerpc/platforms/powermac/pmac.h | 4
arch/powerpc/platforms/powermac/udbg_adb.c | 5
arch/powerpc/platforms/pseries/eeh.c | 52 +++-
arch/powerpc/platforms/pseries/eeh_cache.c | 9 -
arch/powerpc/platforms/pseries/lpar.c | 1
arch/powerpc/platforms/pseries/rtasd.c | 96 +++-----
arch/powerpc/sysdev/dart_iommu.c | 4
arch/powerpc/sysdev/dcr.c | 4
arch/powerpc/sysdev/fsl_soc.c | 13 +
arch/powerpc/sysdev/indirect_pci.c | 4
arch/powerpc/sysdev/tsi108_pci.c | 4
arch/powerpc/sysdev/uic.c | 66 +++++-
arch/ppc/.gitignore | 2
drivers/char/hvc_beat.c | 4
drivers/char/ipmi/ipmi_si_intf.c | 6 -
drivers/macintosh/therm_adt746x.c | 5
drivers/macintosh/via-pmu.c | 2
drivers/macintosh/windfarm_smu_sat.c | 2
drivers/mtd/maps/Kconfig | 2
include/asm-powerpc/atomic.h | 34 ++-
include/asm-powerpc/dma-mapping.h | 24 ++
include/asm-powerpc/lmb.h | 6 -
include/asm-powerpc/nvram.h | 6 -
include/asm-powerpc/page_64.h | 7 +
include/asm-powerpc/prom.h | 1
include/asm-ppc/prom.h | 1
include/linux/of.h | 1
69 files changed, 499 insertions(+), 449 deletions(-)
^ permalink raw reply
* Re: Machine automagically reboots with 2.6.23-rc2-mm2
From: Michael Neuling @ 2007-08-17 2:17 UTC (permalink / raw)
To: balbir; +Cc: linuxppc-dev, Andrew Morton, linux kernel mailing list
In-Reply-To: <46C4C26C.3090502@linux.vnet.ibm.com>
> Hi,
>
> My machine reboots automatically after a few seconds of booting 2.6.23-rc2-mm
2.
> I've tried several ways to debug the problem, but I've had no success.
> I am not sure if this problem has been reported already, a few simple searche
s
> did not indicate that the problem had been reported
>
> 2.6.23-rc1-mm1 did not have this problem.
SLB shadow was bust. Make sure you have
edd0622bd2e8f755c960827e15aa6908c3c5aa94
[POWERPC] Fix potential duplicate entry in SLB shadow buffer
We were getting a duplicate entry in the SLB shadow buffer in
slb_flush_and_rebolt() if the kernel stack was in the same segment
as PAGE_OFFSET, which on POWER6 causes the hypervisor to terminate
the partition with an error. This fixes it.
Also we were not creating an SLB entry (or an SLB shadow buffer
entry) for the kernel stack on secondary CPUs when starting the
CPU. This isn't a major problem, since an appropriate entry will
be created on demand, but this fixes that also for consistency.
Signed-off-by: Paul Mackerras <paulus@samba.org>
>
>
> .config is attached with this email.
>
> /proc/cpuinfo shows
>
> processor : 0
> cpu : POWER5 (gr)
> clock : 1654.344000MHz
> revision : 2.3 (pvr 003a 0203)
>
> processor : 1
> cpu : POWER5 (gr)
> clock : 1654.344000MHz
> revision : 2.3 (pvr 003a 0203)
>
> processor : 2
> cpu : POWER5 (gr)
> clock : 1654.344000MHz
> revision : 2.3 (pvr 003a 0203)
>
> processor : 3
> cpu : POWER5 (gr)
> clock : 1654.344000MHz
> revision : 2.3 (pvr 003a 0203)
>
> timebase : 206998000
> machine : CHRP IBM,9123-710
>
> lspci shows
>
> 00:02.0 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 00:02.2 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 00:02.3 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 00:02.4 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> c0:01.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Contr
oller (Copper) (rev 01)
> c0:01.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Contr
oller (Copper) (rev 01)
> c8:01.0 USB Controller: NEC Corporation USB (rev 43)
> c8:01.1 USB Controller: NEC Corporation USB (rev 43)
> c8:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
> cc:01.0 Mass storage controller: Promise Technology, Inc. 20275 (rev 01)
> d0:01.0 SCSI storage controller: Mylex Corporation AcceleRAID 600/500/400/Sap
phire support Device (rev 04)
> 0001:00:02.2 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 0001:00:02.4 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 0001:00:02.6 PCI bridge: IBM EADS-X PCI-X to PCI-X Bridge (rev 03)
> 0001:d0:01.0 Ethernet controller: Intel Corporation 82545GM Gigabit Ethernet
Controller (rev 04)
>
> Normal kernel boot (memory info)
>
> EEH: PCI Enhanced I/O Error Handling Enabled
> PPC64 nvram contains 7168 bytes
> Using dedicated idle loop
> Top of RAM: 0xe9000000, Total RAM: 0xe9000000
> Memory hole size: 0MB
> On node 0 totalpages: 954368
> DMA zone: 954368 pages, LIFO batch:31
> DMA32 zone: 0 pages, LIFO batch:0
> Normal zone: 0 pages, LIFO batch:0
> HighMem zone: 0 pages, LIFO batch:0
> [boot]0015 Setup Done
> Built 1 zonelists
>
>
> --
> Warm Regards,
> Balbir Singh
> Linux Technology Center
> IBM, ISTL
>
> --------------000300070303050202020703
> Content-Type: text/plain;
> name="config.txt"
> Content-Transfer-Encoding: 7bit
> Content-Disposition: inline;
> filename="config.txt"
>
> #
> # Automatically generated make config: don't edit
> # Linux kernel version: 2.6.23-rc2-mm2
> # Thu Aug 16 15:02:55 2007
> #
> CONFIG_PPC64=y
>
> #
> # Processor support
> #
> # CONFIG_POWER4_ONLY is not set
> CONFIG_POWER3=y
> CONFIG_POWER4=y
> CONFIG_PPC_FPU=y
> CONFIG_ALTIVEC=y
> CONFIG_PPC_STD_MMU=y
> CONFIG_PPC_MM_SLICES=y
> CONFIG_VIRT_CPU_ACCOUNTING=y
> CONFIG_SMP=y
> CONFIG_NR_CPUS=32
> CONFIG_64BIT=y
> CONFIG_PPC_MERGE=y
> CONFIG_MMU=y
> CONFIG_GENERIC_HARDIRQS=y
> CONFIG_IRQ_PER_CPU=y
> CONFIG_RWSEM_XCHGADD_ALGORITHM=y
> CONFIG_ARCH_HAS_ILOG2_U32=y
> CONFIG_ARCH_HAS_ILOG2_U64=y
> CONFIG_GENERIC_HWEIGHT=y
> CONFIG_GENERIC_CALIBRATE_DELAY=y
> CONFIG_GENERIC_FIND_NEXT_BIT=y
> CONFIG_ARCH_NO_VIRT_TO_BUS=y
> CONFIG_PPC=y
> CONFIG_EARLY_PRINTK=y
> CONFIG_COMPAT=y
> CONFIG_SYSVIPC_COMPAT=y
> CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
> CONFIG_ARCH_MAY_HAVE_PC_FDC=y
> CONFIG_PPC_OF=y
> CONFIG_OF=y
> CONFIG_PPC_UDBG_16550=y
> CONFIG_GENERIC_TBSYNC=y
> CONFIG_AUDIT_ARCH=y
> CONFIG_GENERIC_BUG=y
> # CONFIG_DEFAULT_UIMAGE is not set
> CONFIG_PPC64_SWSUSP=y
> # CONFIG_PPC_DCR_NATIVE is not set
> CONFIG_PPC_DCR_MMIO=y
> CONFIG_PPC_DCR=y
> CONFIG_PPC_OF_PLATFORM_PCI=y
> CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
>
> #
> # General setup
> #
> CONFIG_EXPERIMENTAL=y
> CONFIG_LOCK_KERNEL=y
> CONFIG_INIT_ENV_ARG_LIMIT=32
> CONFIG_LOCALVERSION=""
> CONFIG_LOCALVERSION_AUTO=y
> CONFIG_SWAP=y
> CONFIG_SWAP_PREFETCH=y
> CONFIG_SYSVIPC=y
> CONFIG_SYSVIPC_SYSCTL=y
> CONFIG_POSIX_MQUEUE=y
> # CONFIG_BSD_PROCESS_ACCT is not set
> CONFIG_TASKSTATS=y
> CONFIG_TASK_DELAY_ACCT=y
> CONFIG_TASK_XACCT=y
> CONFIG_TASK_IO_ACCOUNTING=y
> # CONFIG_USER_NS is not set
> # CONFIG_AUDIT is not set
> CONFIG_IKCONFIG=y
> CONFIG_IKCONFIG_PROC=y
> CONFIG_LOG_BUF_SHIFT=17
> CONFIG_CONTAINERS=y
> CONFIG_CONTAINER_DEBUG=y
> # CONFIG_CONTAINER_NS is not set
> CONFIG_CONTAINER_CPUACCT=y
> CONFIG_CPUSETS=y
> CONFIG_RESOURCE_COUNTERS=y
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_CONTAINER_MEM_CONT=y
> CONFIG_PROC_PID_CPUSET=y
> CONFIG_RELAY=y
> CONFIG_BLK_DEV_INITRD=y
> CONFIG_INITRAMFS_SOURCE=""
> CONFIG_CC_OPTIMIZE_FOR_SIZE=y
> CONFIG_SYSCTL=y
> # CONFIG_EMBEDDED is not set
> CONFIG_SYSCTL_SYSCALL=y
> CONFIG_KALLSYMS=y
> CONFIG_KALLSYMS_ALL=y
> # CONFIG_KALLSYMS_EXTRA_PASS is not set
> CONFIG_HOTPLUG=y
> CONFIG_PRINTK=y
> CONFIG_BUG=y
> CONFIG_ELF_CORE=y
> CONFIG_BASE_FULL=y
> CONFIG_FUTEX=y
> CONFIG_ANON_INODES=y
> CONFIG_EPOLL=y
> CONFIG_SIGNALFD=y
> CONFIG_TIMERFD=y
> CONFIG_EVENTFD=y
> CONFIG_SHMEM=y
> CONFIG_VM_EVENT_COUNTERS=y
> CONFIG_SLAB=y
> # CONFIG_SLUB is not set
> # CONFIG_SLOB is not set
> CONFIG_PROC_PAGE_MONITOR=y
> CONFIG_PROC_KPAGEMAP=y
> CONFIG_RT_MUTEXES=y
> # CONFIG_TINY_SHMEM is not set
> CONFIG_BASE_SMALL=0
> CONFIG_MODULES=y
> CONFIG_MODULE_UNLOAD=y
> # CONFIG_MODULE_FORCE_UNLOAD is not set
> CONFIG_MODVERSIONS=y
> CONFIG_MODULE_SRCVERSION_ALL=y
> CONFIG_KMOD=y
> CONFIG_STOP_MACHINE=y
> CONFIG_BLOCK=y
> CONFIG_BLK_DEV_IO_TRACE=y
> # CONFIG_BLK_DEV_BSG is not set
>
> #
> # IO Schedulers
> #
> CONFIG_IOSCHED_NOOP=y
> CONFIG_IOSCHED_AS=y
> CONFIG_IOSCHED_DEADLINE=y
> CONFIG_IOSCHED_CFQ=y
> CONFIG_DEFAULT_AS=y
> # CONFIG_DEFAULT_DEADLINE is not set
> # CONFIG_DEFAULT_CFQ is not set
> # CONFIG_DEFAULT_NOOP is not set
> CONFIG_DEFAULT_IOSCHED="anticipatory"
>
> #
> # Platform support
> #
> CONFIG_PPC_MULTIPLATFORM=y
> # CONFIG_EMBEDDED6xx is not set
> # CONFIG_PPC_82xx is not set
> # CONFIG_PPC_83xx is not set
> # CONFIG_PPC_86xx is not set
> CONFIG_PPC_PSERIES=y
> CONFIG_PPC_SPLPAR=y
> CONFIG_EEH=y
> CONFIG_SCANLOG=m
> CONFIG_LPARCFG=y
> CONFIG_PPC_ISERIES=y
>
> #
> # iSeries device drivers
> #
> CONFIG_VIODASD=y
> CONFIG_VIOCD=m
> CONFIG_VIOTAPE=m
> CONFIG_VIOPATH=y
> # CONFIG_PPC_MPC52xx is not set
> # CONFIG_PPC_MPC5200 is not set
> CONFIG_PPC_PMAC=y
> CONFIG_PPC_PMAC64=y
> CONFIG_PPC_MAPLE=y
> # CONFIG_PPC_PASEMI is not set
> # CONFIG_PPC_CELLEB is not set
> # CONFIG_PPC_PS3 is not set
> CONFIG_PPC_CELL=y
> CONFIG_PPC_CELL_NATIVE=y
> CONFIG_PPC_IBM_CELL_BLADE=y
>
> #
> # Cell Broadband Engine options
> #
> CONFIG_SPU_FS=m
> CONFIG_SPU_FS_64K_LS=y
> CONFIG_SPU_BASE=y
> CONFIG_CBE_RAS=y
> CONFIG_CBE_THERM=m
> # CONFIG_PQ2ADS is not set
> CONFIG_PPC_NATIVE=y
> CONFIG_UDBG_RTAS_CONSOLE=y
> CONFIG_XICS=y
> CONFIG_MPIC=y
> # CONFIG_MPIC_WEIRD is not set
> CONFIG_PPC_I8259=y
> CONFIG_U3_DART=y
> CONFIG_PPC_RTAS=y
> CONFIG_RTAS_ERROR_LOGGING=y
> CONFIG_RTAS_PROC=y
> CONFIG_RTAS_FLASH=m
> CONFIG_PPC_PMI=m
> CONFIG_MMIO_NVRAM=y
> CONFIG_MPIC_U3_HT_IRQS=y
> CONFIG_IBMVIO=y
> # CONFIG_IBMEBUS is not set
> # CONFIG_PPC_MPC106 is not set
> CONFIG_PPC_970_NAP=y
> CONFIG_PPC_INDIRECT_IO=y
> CONFIG_GENERIC_IOMAP=y
> # CONFIG_CPU_FREQ is not set
> # CONFIG_CPM2 is not set
> CONFIG_AXON_RAM=m
>
> #
> # Kernel options
> #
> # CONFIG_HZ_100 is not set
> CONFIG_HZ_250=y
> # CONFIG_HZ_300 is not set
> # CONFIG_HZ_1000 is not set
> CONFIG_HZ=250
> CONFIG_PREEMPT_NONE=y
> # CONFIG_PREEMPT_VOLUNTARY is not set
> # CONFIG_PREEMPT is not set
> # CONFIG_PREEMPT_BKL is not set
> CONFIG_BINFMT_ELF=y
> CONFIG_BINFMT_MISC=m
> CONFIG_FORCE_MAX_ZONEORDER=13
> CONFIG_IOMMU_VMERGE=y
> CONFIG_HOTPLUG_CPU=y
> CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
> CONFIG_KEXEC=y
> # CONFIG_CRASH_DUMP is not set
> CONFIG_IRQ_ALL_CPUS=y
> # CONFIG_NUMA is not set
> CONFIG_ARCH_SELECT_MEMORY_MODEL=y
> CONFIG_ARCH_FLATMEM_ENABLE=y
> CONFIG_ARCH_SPARSEMEM_ENABLE=y
> CONFIG_ARCH_SPARSEMEM_DEFAULT=y
> CONFIG_ARCH_POPULATES_NODE_MAP=y
> CONFIG_SELECT_MEMORY_MODEL=y
> # CONFIG_FLATMEM_MANUAL is not set
> # CONFIG_DISCONTIGMEM_MANUAL is not set
> CONFIG_SPARSEMEM_MANUAL=y
> CONFIG_SPARSEMEM=y
> CONFIG_HAVE_MEMORY_PRESENT=y
> # CONFIG_SPARSEMEM_STATIC is not set
> CONFIG_SPARSEMEM_EXTREME=y
> CONFIG_MEMORY_HOTPLUG=y
> CONFIG_MEMORY_HOTPLUG_SPARSE=y
> CONFIG_SPLIT_PTLOCK_CPUS=4
> CONFIG_RESOURCES_64BIT=y
> CONFIG_ZONE_DMA_FLAG=1
> CONFIG_BOUNCE=y
> CONFIG_SPARSEMEM_VMEMMAP=y
> CONFIG_ARCH_POPULATES_SPARSEMEM_VMEMMAP=y
> CONFIG_ARCH_MEMORY_PROBE=y
> CONFIG_PPC_HAS_HASH_64K=y
> # CONFIG_PPC_64K_PAGES is not set
> # CONFIG_SCHED_SMT is not set
> CONFIG_PROC_DEVICETREE=y
> # CONFIG_CMDLINE_BOOL is not set
> # CONFIG_PM is not set
> CONFIG_SUSPEND_SMP_POSSIBLE=y
> CONFIG_HIBERNATION_SMP_POSSIBLE=y
> CONFIG_SECCOMP=y
> # CONFIG_WANT_DEVICE_TREE is not set
> CONFIG_ISA_DMA_API=y
>
> #
> # Bus options
> #
> CONFIG_ZONE_DMA=y
> CONFIG_GENERIC_ISA_DMA=y
> # CONFIG_PPC_INDIRECT_PCI is not set
> CONFIG_PCI=y
> CONFIG_PCI_DOMAINS=y
> CONFIG_PCI_SYSCALL=y
> # CONFIG_PCIEPORTBUS is not set
> CONFIG_ARCH_SUPPORTS_MSI=y
> # CONFIG_PCI_MSI is not set
> # CONFIG_PCI_DEBUG is not set
> # CONFIG_PCCARD is not set
> # CONFIG_HOTPLUG_PCI is not set
> CONFIG_KERNEL_START=0xc000000000000000
>
> #
> # Networking
> #
> CONFIG_NET=y
>
> #
> # Networking options
> #
> CONFIG_PACKET=y
> # CONFIG_PACKET_MMAP is not set
> CONFIG_UNIX=y
> CONFIG_XFRM=y
> CONFIG_XFRM_USER=m
> # CONFIG_XFRM_SUB_POLICY is not set
> # CONFIG_XFRM_MIGRATE is not set
> CONFIG_NET_KEY=m
> # CONFIG_NET_KEY_MIGRATE is not set
> CONFIG_INET=y
> CONFIG_IP_MULTICAST=y
> # CONFIG_IP_ADVANCED_ROUTER is not set
> CONFIG_IP_FIB_HASH=y
> # CONFIG_IP_PNP is not set
> CONFIG_NET_IPIP=y
> # CONFIG_NET_IPGRE is not set
> # CONFIG_IP_MROUTE is not set
> # CONFIG_ARPD is not set
> CONFIG_SYN_COOKIES=y
> CONFIG_INET_AH=m
> CONFIG_INET_ESP=m
> CONFIG_INET_IPCOMP=m
> CONFIG_INET_XFRM_TUNNEL=m
> CONFIG_INET_TUNNEL=y
> CONFIG_INET_XFRM_MODE_TRANSPORT=y
> CONFIG_INET_XFRM_MODE_TUNNEL=y
> CONFIG_INET_XFRM_MODE_BEET=y
> CONFIG_INET_DIAG=y
> CONFIG_INET_TCP_DIAG=y
> # CONFIG_TCP_CONG_ADVANCED is not set
> CONFIG_TCP_CONG_CUBIC=y
> CONFIG_DEFAULT_TCP_CONG="cubic"
> # CONFIG_TCP_MD5SIG is not set
> # CONFIG_IP_VS is not set
> # CONFIG_IPV6 is not set
> # CONFIG_INET6_XFRM_TUNNEL is not set
> # CONFIG_INET6_TUNNEL is not set
> # CONFIG_NETWORK_SECMARK is not set
> CONFIG_NETFILTER=y
> # CONFIG_NETFILTER_DEBUG is not set
>
> #
> # Core Netfilter Configuration
> #
> CONFIG_NETFILTER_NETLINK=y
> CONFIG_NETFILTER_NETLINK_QUEUE=m
> CONFIG_NETFILTER_NETLINK_LOG=m
> CONFIG_NF_CONNTRACK_ENABLED=m
> CONFIG_NF_CONNTRACK=m
> CONFIG_NF_CT_ACCT=y
> CONFIG_NF_CONNTRACK_MARK=y
> CONFIG_NF_CONNTRACK_EVENTS=y
> CONFIG_NF_CT_PROTO_GRE=m
> CONFIG_NF_CT_PROTO_SCTP=m
> # CONFIG_NF_CT_PROTO_UDPLITE is not set
> CONFIG_NF_CONNTRACK_AMANDA=m
> CONFIG_NF_CONNTRACK_FTP=m
> CONFIG_NF_CONNTRACK_H323=m
> CONFIG_NF_CONNTRACK_IRC=m
> CONFIG_NF_CONNTRACK_NETBIOS_NS=m
> CONFIG_NF_CONNTRACK_PPTP=m
> # CONFIG_NF_CONNTRACK_SANE is not set
> CONFIG_NF_CONNTRACK_SIP=m
> CONFIG_NF_CONNTRACK_TFTP=m
> CONFIG_NF_CT_NETLINK=m
> # CONFIG_NETFILTER_XTABLES is not set
>
> #
> # IP: Netfilter Configuration
> #
> CONFIG_NF_CONNTRACK_IPV4=m
> CONFIG_NF_CONNTRACK_PROC_COMPAT=y
> CONFIG_IP_NF_QUEUE=m
> # CONFIG_IP_NF_IPTABLES is not set
> # CONFIG_IP_NF_ARPTABLES is not set
> # CONFIG_IP_DCCP is not set
> # CONFIG_IP_SCTP is not set
> # CONFIG_TIPC is not set
> # CONFIG_ATM is not set
> # CONFIG_BRIDGE is not set
> # CONFIG_VLAN_8021Q is not set
> # CONFIG_DECNET is not set
> CONFIG_LLC=y
> # CONFIG_LLC2 is not set
> # CONFIG_IPX is not set
> # CONFIG_ATALK is not set
> # CONFIG_X25 is not set
> # CONFIG_LAPB is not set
> # CONFIG_ECONET is not set
> # CONFIG_WAN_ROUTER is not set
>
> #
> # QoS and/or fair queueing
> #
> # CONFIG_NET_SCHED is not set
>
> #
> # Network testing
> #
> # CONFIG_NET_PKTGEN is not set
> # CONFIG_HAMRADIO is not set
> # CONFIG_IRDA is not set
> # CONFIG_BT is not set
> # CONFIG_AF_RXRPC is not set
>
> #
> # Wireless
> #
> # CONFIG_CFG80211 is not set
> # CONFIG_WIRELESS_EXT is not set
> # CONFIG_MAC80211 is not set
> # CONFIG_IEEE80211 is not set
> # CONFIG_RFKILL is not set
> # CONFIG_NET_9P is not set
>
> #
> # Device Drivers
> #
>
> #
> # Generic Driver Options
> #
> CONFIG_STANDALONE=y
> CONFIG_PREVENT_FIRMWARE_BUILD=y
> CONFIG_FW_LOADER=y
> # CONFIG_DEBUG_DRIVER is not set
> # CONFIG_DEBUG_DEVRES is not set
> # CONFIG_SYS_HYPERVISOR is not set
> # CONFIG_CONNECTOR is not set
> # CONFIG_MTD is not set
> CONFIG_OF_DEVICE=y
> # CONFIG_PARPORT is not set
> CONFIG_BLK_DEV=y
> CONFIG_BLK_DEV_FD=y
> # CONFIG_BLK_CPQ_CISS_DA is not set
> # CONFIG_BLK_DEV_DAC960 is not set
> # CONFIG_BLK_DEV_UMEM is not set
> # CONFIG_BLK_DEV_COW_COMMON is not set
> CONFIG_BLK_DEV_LOOP=y
> # CONFIG_BLK_DEV_CRYPTOLOOP is not set
> CONFIG_BLK_DEV_NBD=m
> # CONFIG_BLK_DEV_SX8 is not set
> # CONFIG_BLK_DEV_UB is not set
> CONFIG_BLK_DEV_RAM=y
> CONFIG_BLK_DEV_RAM_COUNT=16
> CONFIG_BLK_DEV_RAM_SIZE=65536
> CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
> # CONFIG_CDROM_PKTCDVD is not set
> # CONFIG_ATA_OVER_ETH is not set
> CONFIG_MISC_DEVICES=y
> # CONFIG_PHANTOM is not set
> # CONFIG_EEPROM_93CX6 is not set
> # CONFIG_SGI_IOC4 is not set
> # CONFIG_TIFM_CORE is not set
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_IDE_SATA is not set
> CONFIG_BLK_DEV_IDEDISK=y
> # CONFIG_IDEDISK_MULTI_MODE is not set
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> # CONFIG_BLK_DEV_IDEFLOPPY is not set
> # CONFIG_BLK_DEV_IDESCSI is not set
> # CONFIG_IDE_TASK_IOCTL is not set
> CONFIG_IDE_PROC_FS=y
>
> #
> # IDE chipset support/bugfixes
> #
> CONFIG_IDE_GENERIC=y
> # CONFIG_BLK_DEV_PLATFORM is not set
>
> #
> # PCI IDE chipsets support
> #
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> CONFIG_IDEPCI_PCIBUS_ORDER=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> CONFIG_BLK_DEV_GENERIC=y
> # CONFIG_BLK_DEV_OPTI621 is not set
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> # CONFIG_IDEDMA_ONLYDISK is not set
> # CONFIG_BLK_DEV_AEC62XX is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> CONFIG_BLK_DEV_AMD74XX=y
> # CONFIG_BLK_DEV_CMD64X is not set
> # CONFIG_BLK_DEV_TRIFLEX is not set
> # CONFIG_BLK_DEV_CY82C693 is not set
> # CONFIG_BLK_DEV_CS5520 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_BLK_DEV_HPT34X is not set
> # CONFIG_BLK_DEV_HPT366 is not set
> # CONFIG_BLK_DEV_JMICRON is not set
> # CONFIG_BLK_DEV_SC1200 is not set
> # CONFIG_BLK_DEV_PIIX is not set
> # CONFIG_BLK_DEV_IT8213 is not set
> # CONFIG_BLK_DEV_IT821X is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> # CONFIG_BLK_DEV_PDC202XX_OLD is not set
> # CONFIG_BLK_DEV_PDC202XX_NEW is not set
> # CONFIG_BLK_DEV_SVWKS is not set
> # CONFIG_BLK_DEV_SIIMAGE is not set
> # CONFIG_BLK_DEV_SL82C105 is not set
> # CONFIG_BLK_DEV_SLC90E66 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_VIA82CXXX is not set
> # CONFIG_BLK_DEV_TC86C001 is not set
> CONFIG_BLK_DEV_IDE_PMAC=y
> CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
> CONFIG_BLK_DEV_IDEDMA_PMAC=y
> # CONFIG_IDE_ARM is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_BLK_DEV_HD is not set
>
> #
> # SCSI device support
> #
> # CONFIG_RAID_ATTRS is not set
> CONFIG_SCSI=y
> CONFIG_SCSI_DMA=y
> # CONFIG_SCSI_TGT is not set
> CONFIG_SCSI_NETLINK=y
> CONFIG_SCSI_PROC_FS=y
>
> #
> # SCSI support type (disk, tape, CD-ROM)
> #
> CONFIG_BLK_DEV_SD=y
> CONFIG_CHR_DEV_ST=y
> # CONFIG_CHR_DEV_OSST is not set
> CONFIG_BLK_DEV_SR=y
> CONFIG_BLK_DEV_SR_VENDOR=y
> CONFIG_CHR_DEV_SG=y
> # CONFIG_CHR_DEV_SCH is not set
>
> #
> # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
> #
> CONFIG_SCSI_MULTI_LUN=y
> CONFIG_SCSI_CONSTANTS=y
> # CONFIG_SCSI_LOGGING is not set
> # CONFIG_SCSI_SCAN_ASYNC is not set
> CONFIG_SCSI_WAIT_SCAN=m
>
> #
> # SCSI Transports
> #
> CONFIG_SCSI_SPI_ATTRS=y
> CONFIG_SCSI_FC_ATTRS=y
> CONFIG_SCSI_ISCSI_ATTRS=m
> # CONFIG_SCSI_SAS_LIBSAS is not set
> CONFIG_SCSI_SRP_ATTRS=y
> CONFIG_SCSI_LOWLEVEL=y
> # CONFIG_ISCSI_TCP is not set
> # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
> # CONFIG_SCSI_3W_9XXX is not set
> # CONFIG_SCSI_ACARD is not set
> # CONFIG_SCSI_AACRAID is not set
> # CONFIG_SCSI_AIC7XXX is not set
> # CONFIG_SCSI_AIC7XXX_OLD is not set
> # CONFIG_SCSI_AIC79XX is not set
> # CONFIG_SCSI_AIC94XX is not set
> # CONFIG_SCSI_ARCMSR is not set
> # CONFIG_MEGARAID_NEWGEN is not set
> # CONFIG_MEGARAID_LEGACY is not set
> # CONFIG_MEGARAID_SAS is not set
> # CONFIG_SCSI_HPTIOP is not set
> # CONFIG_SCSI_DMX3191D is not set
> # CONFIG_SCSI_EATA is not set
> # CONFIG_SCSI_FUTURE_DOMAIN is not set
> # CONFIG_SCSI_GDTH is not set
> # CONFIG_SCSI_IPS is not set
> CONFIG_SCSI_IBMVSCSI=y
> # CONFIG_SCSI_INITIO is not set
> # CONFIG_SCSI_INIA100 is not set
> # CONFIG_SCSI_STEX is not set
> CONFIG_SCSI_SYM53C8XX_2=y
> CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
> CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
> CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
> CONFIG_SCSI_SYM53C8XX_MMIO=y
> CONFIG_SCSI_IPR=y
> CONFIG_SCSI_IPR_TRACE=y
> CONFIG_SCSI_IPR_DUMP=y
> # CONFIG_SCSI_QLOGIC_1280 is not set
> # CONFIG_SCSI_QLA_FC is not set
> # CONFIG_SCSI_QLA_ISCSI is not set
> CONFIG_SCSI_LPFC=m
> # CONFIG_SCSI_DC395x is not set
> # CONFIG_SCSI_DC390T is not set
> CONFIG_SCSI_DEBUG=m
> # CONFIG_SCSI_SRP is not set
> CONFIG_ATA=y
> CONFIG_ATA_NONSTANDARD=y
> # CONFIG_SATA_AHCI is not set
> CONFIG_SATA_SVW=y
> # CONFIG_ATA_PIIX is not set
> # CONFIG_SATA_MV is not set
> # CONFIG_SATA_NV is not set
> # CONFIG_PDC_ADMA is not set
> # CONFIG_SATA_QSTOR is not set
> # CONFIG_SATA_PROMISE is not set
> # CONFIG_SATA_SX4 is not set
> # CONFIG_SATA_SIL is not set
> # CONFIG_SATA_SIL24 is not set
> # CONFIG_SATA_SIS is not set
> # CONFIG_SATA_ULI is not set
> # CONFIG_SATA_VIA is not set
> # CONFIG_SATA_VITESSE is not set
> # CONFIG_SATA_INIC162X is not set
> # CONFIG_PATA_ALI is not set
> # CONFIG_PATA_AMD is not set
> # CONFIG_PATA_ARTOP is not set
> # CONFIG_PATA_ATIIXP is not set
> # CONFIG_PATA_CMD640_PCI is not set
> # CONFIG_PATA_CMD64X is not set
> # CONFIG_PATA_CS5520 is not set
> # CONFIG_PATA_CS5530 is not set
> # CONFIG_PATA_CYPRESS is not set
> # CONFIG_PATA_EFAR is not set
> # CONFIG_ATA_GENERIC is not set
> # CONFIG_PATA_HPT366 is not set
> # CONFIG_PATA_HPT37X is not set
> # CONFIG_PATA_HPT3X2N is not set
> # CONFIG_PATA_HPT3X3 is not set
> # CONFIG_PATA_IT821X is not set
> # CONFIG_PATA_IT8213 is not set
> # CONFIG_PATA_JMICRON is not set
> # CONFIG_PATA_TRIFLEX is not set
> # CONFIG_PATA_MARVELL is not set
> # CONFIG_PATA_MPIIX is not set
> # CONFIG_PATA_OLDPIIX is not set
> # CONFIG_PATA_NETCELL is not set
> # CONFIG_PATA_NS87410 is not set
> # CONFIG_PATA_OPTI is not set
> # CONFIG_PATA_OPTIDMA is not set
> # CONFIG_PATA_PDC_OLD is not set
> # CONFIG_PATA_RADISYS is not set
> # CONFIG_PATA_RZ1000 is not set
> # CONFIG_PATA_SC1200 is not set
> # CONFIG_PATA_SERVERWORKS is not set
> # CONFIG_PATA_PDC2027X is not set
> # CONFIG_PATA_SIL680 is not set
> # CONFIG_PATA_SIS is not set
> # CONFIG_PATA_VIA is not set
> CONFIG_PATA_WINBOND=y
> CONFIG_MD=y
> CONFIG_BLK_DEV_MD=y
> CONFIG_MD_LINEAR=y
> CONFIG_MD_RAID0=y
> CONFIG_MD_RAID1=y
> CONFIG_MD_RAID10=y
> CONFIG_MD_RAID456=y
> CONFIG_MD_RAID5_RESHAPE=y
> CONFIG_MD_MULTIPATH=m
> CONFIG_MD_FAULTY=m
> CONFIG_BLK_DEV_DM=y
> # CONFIG_DM_DEBUG is not set
> CONFIG_DM_CRYPT=m
> CONFIG_DM_SNAPSHOT=m
> CONFIG_DM_MIRROR=m
> CONFIG_DM_ZERO=m
> CONFIG_DM_MULTIPATH=m
> CONFIG_DM_MULTIPATH_EMC=m
> # CONFIG_DM_MULTIPATH_RDAC is not set
> # CONFIG_DM_DELAY is not set
> # CONFIG_FUSION is not set
>
> #
> # IEEE 1394 (FireWire) support
> #
> # CONFIG_FIREWIRE is not set
> CONFIG_IEEE1394=y
>
> #
> # Subsystem Options
> #
> # CONFIG_IEEE1394_VERBOSEDEBUG is not set
>
> #
> # Controllers
> #
> # CONFIG_IEEE1394_PCILYNX is not set
> CONFIG_IEEE1394_OHCI1394=y
>
> #
> # Protocols
> #
> CONFIG_IEEE1394_VIDEO1394=m
> CONFIG_IEEE1394_SBP2=m
> CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
> CONFIG_IEEE1394_ETH1394=m
> CONFIG_IEEE1394_DV1394=m
> CONFIG_IEEE1394_RAWIO=y
> # CONFIG_I2O is not set
> CONFIG_MACINTOSH_DRIVERS=y
> CONFIG_ADB_PMU=y
> # CONFIG_ADB_PMU_LED is not set
> CONFIG_PMAC_SMU=y
> # CONFIG_MAC_EMUMOUSEBTN is not set
> CONFIG_THERM_PM72=y
> CONFIG_WINDFARM=y
> CONFIG_WINDFARM_PM112=y
> # CONFIG_PMAC_RACKMETER is not set
> CONFIG_NETDEVICES=y
> # CONFIG_NETDEVICES_MULTIQUEUE is not set
> CONFIG_DUMMY=m
> CONFIG_BONDING=m
> # CONFIG_MACVLAN is not set
> # CONFIG_EQUALIZER is not set
> CONFIG_TUN=m
> # CONFIG_ARCNET is not set
> # CONFIG_PHYLIB is not set
> CONFIG_NET_ETHERNET=y
> CONFIG_MII=y
> # CONFIG_HAPPYMEAL is not set
> CONFIG_SUNGEM=y
> # CONFIG_CASSINI is not set
> CONFIG_NET_VENDOR_3COM=y
> CONFIG_VORTEX=y
> # CONFIG_TYPHOON is not set
> # CONFIG_NET_TULIP is not set
> # CONFIG_HP100 is not set
> CONFIG_IBMVETH=m
> CONFIG_NET_PCI=y
> CONFIG_PCNET32=y
> # CONFIG_PCNET32_NAPI is not set
> # CONFIG_AMD8111_ETH is not set
> # CONFIG_ADAPTEC_STARFIRE is not set
> # CONFIG_FORCEDETH is not set
> # CONFIG_DGRS is not set
> # CONFIG_EEPRO100 is not set
> CONFIG_E100=y
> # CONFIG_FEALNX is not set
> # CONFIG_NATSEMI is not set
> # CONFIG_NE2K_PCI is not set
> # CONFIG_8139CP is not set
> # CONFIG_8139TOO is not set
> # CONFIG_SIS900 is not set
> # CONFIG_EPIC100 is not set
> # CONFIG_SUNDANCE is not set
> # CONFIG_VIA_RHINE is not set
> # CONFIG_SC92031 is not set
> CONFIG_NETDEV_1000=y
> CONFIG_ACENIC=y
> CONFIG_ACENIC_OMIT_TIGON_I=y
> # CONFIG_DL2K is not set
> CONFIG_E1000=y
> # CONFIG_E1000_NAPI is not set
> # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
> # CONFIG_E1000E is not set
> # CONFIG_NS83820 is not set
> # CONFIG_HAMACHI is not set
> # CONFIG_YELLOWFIN is not set
> # CONFIG_R8169 is not set
> # CONFIG_SIS190 is not set
> # CONFIG_SKGE is not set
> # CONFIG_SKY2 is not set
> # CONFIG_VIA_VELOCITY is not set
> CONFIG_TIGON3=y
> # CONFIG_BNX2 is not set
> CONFIG_SPIDER_NET=m
> # CONFIG_QLA3XXX is not set
> # CONFIG_ATL1 is not set
> CONFIG_NETDEV_10000=y
> # CONFIG_CHELSIO_T1 is not set
> # CONFIG_CHELSIO_T3 is not set
> CONFIG_IXGB=m
> # CONFIG_IXGB_NAPI is not set
> # CONFIG_IXGBE is not set
> # CONFIG_S2IO is not set
> # CONFIG_MYRI10GE is not set
> # CONFIG_NETXEN_NIC is not set
> # CONFIG_PASEMI_MAC is not set
> # CONFIG_MLX4_CORE is not set
> CONFIG_TR=y
> CONFIG_IBMOL=y
> # CONFIG_3C359 is not set
> # CONFIG_TMS380TR is not set
>
> #
> # Wireless LAN
> #
> # CONFIG_WLAN_PRE80211 is not set
> # CONFIG_WLAN_80211 is not set
>
> #
> # USB Network Adapters
> #
> # CONFIG_USB_CATC is not set
> # CONFIG_USB_KAWETH is not set
> # CONFIG_USB_PEGASUS is not set
> # CONFIG_USB_RTL8150 is not set
> # CONFIG_USB_USBNET_MII is not set
> # CONFIG_USB_USBNET is not set
> # CONFIG_WAN is not set
> CONFIG_ISERIES_VETH=m
> # CONFIG_FDDI is not set
> # CONFIG_HIPPI is not set
> CONFIG_PPP=m
> # CONFIG_PPP_MULTILINK is not set
> # CONFIG_PPP_FILTER is not set
> CONFIG_PPP_ASYNC=m
> CONFIG_PPP_SYNC_TTY=m
> CONFIG_PPP_DEFLATE=m
> CONFIG_PPP_BSDCOMP=m
> # CONFIG_PPP_MPPE is not set
> CONFIG_PPPOE=m
> # CONFIG_PPPOL2TP is not set
> # CONFIG_SLIP is not set
> CONFIG_SLHC=m
> # CONFIG_NET_FC is not set
> # CONFIG_SHAPER is not set
> CONFIG_NETCONSOLE=y
> # CONFIG_NETCONSOLE_DYNAMIC is not set
> CONFIG_NETPOLL=y
> CONFIG_NETPOLL_TRAP=y
> CONFIG_NET_POLL_CONTROLLER=y
> # CONFIG_ISDN is not set
> # CONFIG_PHONE is not set
>
> #
> # Input device support
> #
> CONFIG_INPUT=y
> # CONFIG_INPUT_FF_MEMLESS is not set
> # CONFIG_INPUT_POLLDEV is not set
>
> #
> # Userland interfaces
> #
> CONFIG_INPUT_MOUSEDEV=y
> # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
> CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
> CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
> # CONFIG_INPUT_JOYDEV is not set
> # CONFIG_INPUT_TSDEV is not set
> CONFIG_INPUT_EVDEV=m
> # CONFIG_INPUT_EVBUG is not set
>
> #
> # Input Device Drivers
> #
> CONFIG_INPUT_KEYBOARD=y
> CONFIG_KEYBOARD_ATKBD=y
> # CONFIG_KEYBOARD_SUNKBD is not set
> # CONFIG_KEYBOARD_LKKBD is not set
> # CONFIG_KEYBOARD_XTKBD is not set
> # CONFIG_KEYBOARD_NEWTON is not set
> # CONFIG_KEYBOARD_STOWAWAY is not set
> CONFIG_INPUT_MOUSE=y
> CONFIG_MOUSE_PS2=y
> CONFIG_MOUSE_PS2_ALPS=y
> CONFIG_MOUSE_PS2_LOGIPS2PP=y
> CONFIG_MOUSE_PS2_SYNAPTICS=y
> CONFIG_MOUSE_PS2_LIFEBOOK=y
> CONFIG_MOUSE_PS2_TRACKPOINT=y
> # CONFIG_MOUSE_PS2_TOUCHKIT is not set
> # CONFIG_MOUSE_SERIAL is not set
> # CONFIG_MOUSE_APPLETOUCH is not set
> # CONFIG_MOUSE_VSXXXAA is not set
> # CONFIG_INPUT_JOYSTICK is not set
> # CONFIG_INPUT_TABLET is not set
> # CONFIG_INPUT_TOUCHSCREEN is not set
> CONFIG_INPUT_MISC=y
> CONFIG_INPUT_PCSPKR=m
> # CONFIG_INPUT_ATI_REMOTE is not set
> # CONFIG_INPUT_ATI_REMOTE2 is not set
> # CONFIG_INPUT_KEYSPAN_REMOTE is not set
> # CONFIG_INPUT_POWERMATE is not set
> # CONFIG_INPUT_YEALINK is not set
> # CONFIG_INPUT_UINPUT is not set
>
> #
> # Hardware I/O ports
> #
> CONFIG_SERIO=y
> CONFIG_SERIO_I8042=y
> # CONFIG_SERIO_SERPORT is not set
> # CONFIG_SERIO_PCIPS2 is not set
> CONFIG_SERIO_LIBPS2=y
> # CONFIG_SERIO_RAW is not set
> # CONFIG_GAMEPORT is not set
>
> #
> # Character devices
> #
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> CONFIG_HW_CONSOLE=y
> # CONFIG_VT_HW_CONSOLE_BINDING is not set
> # CONFIG_SERIAL_NONSTANDARD is not set
> # CONFIG_NOZOMI is not set
>
> #
> # Serial drivers
> #
> CONFIG_SERIAL_8250=y
> CONFIG_SERIAL_8250_CONSOLE=y
> CONFIG_SERIAL_8250_PCI=y
> CONFIG_SERIAL_8250_NR_UARTS=4
> CONFIG_SERIAL_8250_RUNTIME_UARTS=4
> # CONFIG_SERIAL_8250_EXTENDED is not set
>
> #
> # Non-8250 serial port support
> #
> CONFIG_SERIAL_CORE=y
> CONFIG_SERIAL_CORE_CONSOLE=y
> # CONFIG_SERIAL_PMACZILOG is not set
> CONFIG_SERIAL_ICOM=m
> # CONFIG_SERIAL_JSM is not set
> # CONFIG_SERIAL_OF_PLATFORM is not set
> CONFIG_UNIX98_PTYS=y
> CONFIG_LEGACY_PTYS=y
> CONFIG_LEGACY_PTY_COUNT=256
> CONFIG_HVC_DRIVER=y
> CONFIG_HVC_CONSOLE=y
> CONFIG_HVC_ISERIES=y
> CONFIG_HVC_RTAS=y
> CONFIG_HVCS=m
> # CONFIG_IPMI_HANDLER is not set
> # CONFIG_WATCHDOG is not set
> # CONFIG_HW_RANDOM is not set
> CONFIG_GEN_RTC=y
> # CONFIG_GEN_RTC_X is not set
> # CONFIG_R3964 is not set
> # CONFIG_APPLICOM is not set
> # CONFIG_AGP is not set
> # CONFIG_DRM is not set
> CONFIG_RAW_DRIVER=y
> CONFIG_MAX_RAW_DEVS=256
> # CONFIG_HANGCHECK_TIMER is not set
> # CONFIG_TCG_TPM is not set
> CONFIG_DEVPORT=y
> CONFIG_I2C=y
> CONFIG_I2C_BOARDINFO=y
> CONFIG_I2C_CHARDEV=y
>
> #
> # I2C Algorithms
> #
> CONFIG_I2C_ALGOBIT=y
> # CONFIG_I2C_ALGOPCF is not set
> # CONFIG_I2C_ALGOPCA is not set
>
> #
> # I2C Hardware Bus support
> #
> # CONFIG_I2C_ALI1535 is not set
> # CONFIG_I2C_ALI1563 is not set
> # CONFIG_I2C_ALI15X3 is not set
> # CONFIG_I2C_AMD756 is not set
> CONFIG_I2C_AMD8111=y
> # CONFIG_I2C_I801 is not set
> # CONFIG_I2C_I810 is not set
> # CONFIG_I2C_PIIX4 is not set
> CONFIG_I2C_POWERMAC=y
> # CONFIG_I2C_NFORCE2 is not set
> # CONFIG_I2C_OCORES is not set
> # CONFIG_I2C_PARPORT_LIGHT is not set
> # CONFIG_I2C_PROSAVAGE is not set
> # CONFIG_I2C_SAVAGE4 is not set
> # CONFIG_I2C_SIMTEC is not set
> # CONFIG_I2C_SIS5595 is not set
> # CONFIG_I2C_SIS630 is not set
> # CONFIG_I2C_SIS96X is not set
> # CONFIG_I2C_TAOS_EVM is not set
> # CONFIG_I2C_STUB is not set
> # CONFIG_I2C_TINY_USB is not set
> # CONFIG_I2C_VIA is not set
> # CONFIG_I2C_VIAPRO is not set
> # CONFIG_I2C_VOODOO3 is not set
>
> #
> # Miscellaneous I2C Chip support
> #
> # CONFIG_SENSORS_DS1337 is not set
> # CONFIG_SENSORS_DS1374 is not set
> # CONFIG_SENSORS_DS1682 is not set
> # CONFIG_SENSORS_EEPROM is not set
> # CONFIG_SENSORS_PCF8574 is not set
> # CONFIG_SENSORS_PCA9539 is not set
> # CONFIG_SENSORS_PCF8591 is not set
> # CONFIG_SENSORS_MAX6875 is not set
> # CONFIG_SENSORS_TSL2550 is not set
> # CONFIG_I2C_DEBUG_CORE is not set
> # CONFIG_I2C_DEBUG_ALGO is not set
> # CONFIG_I2C_DEBUG_BUS is not set
> # CONFIG_I2C_DEBUG_CHIP is not set
>
> #
> # SPI support
> #
> # CONFIG_SPI is not set
> # CONFIG_SPI_MASTER is not set
> # CONFIG_W1 is not set
> # CONFIG_POWER_SUPPLY is not set
> # CONFIG_HWMON is not set
>
> #
> # Sonics Silicon Backplane
> #
> # CONFIG_SSB is not set
>
> #
> # Multifunction device drivers
> #
> # CONFIG_MFD_SM501 is not set
>
> #
> # Multimedia devices
> #
> # CONFIG_VIDEO_DEV is not set
> # CONFIG_DVB_CORE is not set
> CONFIG_DAB=y
> # CONFIG_USB_DABUSB is not set
>
> #
> # Graphics support
> #
> CONFIG_BACKLIGHT_LCD_SUPPORT=y
> CONFIG_LCD_CLASS_DEVICE=y
> CONFIG_BACKLIGHT_CLASS_DEVICE=y
>
> #
> # Display device support
> #
> # CONFIG_DISPLAY_SUPPORT is not set
> # CONFIG_VGASTATE is not set
> # CONFIG_VIDEO_OUTPUT_CONTROL is not set
> CONFIG_FB=y
> CONFIG_FIRMWARE_EDID=y
> CONFIG_FB_DDC=y
> CONFIG_FB_CFB_FILLRECT=y
> CONFIG_FB_CFB_COPYAREA=y
> CONFIG_FB_CFB_IMAGEBLIT=y
> # CONFIG_FB_SYS_FILLRECT is not set
> # CONFIG_FB_SYS_COPYAREA is not set
> # CONFIG_FB_SYS_IMAGEBLIT is not set
> # CONFIG_FB_SYS_FOPS is not set
> CONFIG_FB_DEFERRED_IO=y
> # CONFIG_FB_SVGALIB is not set
> CONFIG_FB_MACMODES=y
> CONFIG_FB_BACKLIGHT=y
> CONFIG_FB_MODE_HELPERS=y
> CONFIG_FB_TILEBLITTING=y
>
> #
> # Frame buffer hardware drivers
> #
> # CONFIG_FB_CIRRUS is not set
> # CONFIG_FB_PM2 is not set
> # CONFIG_FB_CYBER2000 is not set
> CONFIG_FB_OF=y
> # CONFIG_FB_ASILIANT is not set
> # CONFIG_FB_IMSTT is not set
> # CONFIG_FB_VGA16 is not set
> # CONFIG_FB_S1D13XXX is not set
> # CONFIG_FB_NVIDIA is not set
> # CONFIG_FB_RIVA is not set
> CONFIG_FB_MATROX=y
> CONFIG_FB_MATROX_MILLENIUM=y
> CONFIG_FB_MATROX_MYSTIQUE=y
> CONFIG_FB_MATROX_G=y
> CONFIG_FB_MATROX_I2C=m
> CONFIG_FB_MATROX_MAVEN=m
> CONFIG_FB_MATROX_MULTIHEAD=y
> CONFIG_FB_RADEON=y
> CONFIG_FB_RADEON_I2C=y
> CONFIG_FB_RADEON_BACKLIGHT=y
> # CONFIG_FB_RADEON_DEBUG is not set
> # CONFIG_FB_ATY128 is not set
> # CONFIG_FB_ATY is not set
> # CONFIG_FB_S3 is not set
> # CONFIG_FB_SAVAGE is not set
> # CONFIG_FB_SIS is not set
> # CONFIG_FB_NEOMAGIC is not set
> # CONFIG_FB_KYRO is not set
> # CONFIG_FB_3DFX is not set
> # CONFIG_FB_VOODOO1 is not set
> # CONFIG_FB_VT8623 is not set
> # CONFIG_FB_TRIDENT is not set
> # CONFIG_FB_ARK is not set
> # CONFIG_FB_PM3 is not set
> CONFIG_FB_IBM_GXT4500=y
> # CONFIG_FB_VIRTUAL is not set
>
> #
> # Console display driver support
> #
> # CONFIG_VGA_CONSOLE is not set
> CONFIG_DUMMY_CONSOLE=y
> CONFIG_FRAMEBUFFER_CONSOLE=y
> # CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
> # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> # CONFIG_FONTS is not set
> CONFIG_FONT_8x8=y
> CONFIG_FONT_8x16=y
> CONFIG_LOGO=y
> CONFIG_FB_LOGO_EXTRA=y
> CONFIG_LOGO_LINUX_MONO=y
> CONFIG_LOGO_LINUX_VGA16=y
> CONFIG_LOGO_LINUX_CLUT224=y
>
> #
> # Sound
> #
> CONFIG_SOUND=m
>
> #
> # Advanced Linux Sound Architecture
> #
> CONFIG_SND=m
> CONFIG_SND_TIMER=m
> CONFIG_SND_PCM=m
> CONFIG_SND_SEQUENCER=m
> CONFIG_SND_SEQ_DUMMY=m
> CONFIG_SND_OSSEMUL=y
> CONFIG_SND_MIXER_OSS=m
> CONFIG_SND_PCM_OSS=m
> CONFIG_SND_PCM_OSS_PLUGINS=y
> CONFIG_SND_SEQUENCER_OSS=y
> # CONFIG_SND_DYNAMIC_MINORS is not set
> CONFIG_SND_SUPPORT_OLD_API=y
> CONFIG_SND_VERBOSE_PROCFS=y
> # CONFIG_SND_VERBOSE_PRINTK is not set
> # CONFIG_SND_DEBUG is not set
>
> #
> # Generic devices
> #
> # CONFIG_SND_DUMMY is not set
> # CONFIG_SND_VIRMIDI is not set
> # CONFIG_SND_MTPAV is not set
> # CONFIG_SND_SERIAL_U16550 is not set
> # CONFIG_SND_MPU401 is not set
>
> #
> # PCI devices
> #
> # CONFIG_SND_AD1889 is not set
> # CONFIG_SND_ALS300 is not set
> # CONFIG_SND_ALS4000 is not set
> # CONFIG_SND_ALI5451 is not set
> # CONFIG_SND_ATIIXP is not set
> # CONFIG_SND_ATIIXP_MODEM is not set
> # CONFIG_SND_AU8810 is not set
> # CONFIG_SND_AU8820 is not set
> # CONFIG_SND_AU8830 is not set
> # CONFIG_SND_AZT3328 is not set
> # CONFIG_SND_BT87X is not set
> # CONFIG_SND_CA0106 is not set
> # CONFIG_SND_CMIPCI is not set
> # CONFIG_SND_CS4281 is not set
> # CONFIG_SND_CS46XX is not set
> # CONFIG_SND_CS5530 is not set
> # CONFIG_SND_DARLA20 is not set
> # CONFIG_SND_GINA20 is not set
> # CONFIG_SND_LAYLA20 is not set
> # CONFIG_SND_DARLA24 is not set
> # CONFIG_SND_GINA24 is not set
> # CONFIG_SND_LAYLA24 is not set
> # CONFIG_SND_MONA is not set
> # CONFIG_SND_MIA is not set
> # CONFIG_SND_ECHO3G is not set
> # CONFIG_SND_INDIGO is not set
> # CONFIG_SND_INDIGOIO is not set
> # CONFIG_SND_INDIGODJ is not set
> # CONFIG_SND_EMU10K1 is not set
> # CONFIG_SND_EMU10K1X is not set
> # CONFIG_SND_ENS1370 is not set
> # CONFIG_SND_ENS1371 is not set
> # CONFIG_SND_ES1938 is not set
> # CONFIG_SND_ES1968 is not set
> # CONFIG_SND_FM801 is not set
> # CONFIG_SND_HDA_INTEL is not set
> # CONFIG_SND_HDSP is not set
> # CONFIG_SND_HDSPM is not set
> # CONFIG_SND_ICE1712 is not set
> # CONFIG_SND_ICE1724 is not set
> # CONFIG_SND_INTEL8X0 is not set
> # CONFIG_SND_INTEL8X0M is not set
> # CONFIG_SND_KORG1212 is not set
> # CONFIG_SND_MAESTRO3 is not set
> # CONFIG_SND_MIXART is not set
> # CONFIG_SND_NM256 is not set
> # CONFIG_SND_PCXHR is not set
> # CONFIG_SND_RIPTIDE is not set
> # CONFIG_SND_RME32 is not set
> # CONFIG_SND_RME96 is not set
> # CONFIG_SND_RME9652 is not set
> # CONFIG_SND_SONICVIBES is not set
> # CONFIG_SND_TRIDENT is not set
> # CONFIG_SND_VIA82XX is not set
> # CONFIG_SND_VIA82XX_MODEM is not set
> # CONFIG_SND_VX222 is not set
> # CONFIG_SND_YMFPCI is not set
>
> #
> # ALSA PowerMac devices
> #
> CONFIG_SND_POWERMAC=m
> CONFIG_SND_POWERMAC_AUTO_DRC=y
>
> #
> # ALSA PowerPC devices
> #
>
> #
> # Apple Onboard Audio driver
> #
> CONFIG_SND_AOA=m
> CONFIG_SND_AOA_FABRIC_LAYOUT=m
> CONFIG_SND_AOA_ONYX=m
> CONFIG_SND_AOA_TAS=m
> CONFIG_SND_AOA_TOONIE=m
> CONFIG_SND_AOA_SOUNDBUS=m
> CONFIG_SND_AOA_SOUNDBUS_I2S=m
>
> #
> # USB devices
> #
> # CONFIG_SND_USB_AUDIO is not set
> # CONFIG_SND_USB_USX2Y is not set
> # CONFIG_SND_USB_CAIAQ is not set
>
> #
> # System on Chip audio support
> #
> # CONFIG_SND_SOC is not set
>
> #
> # SoC Audio support for SuperH
> #
>
> #
> # Open Sound System
> #
> # CONFIG_SOUND_PRIME is not set
> CONFIG_HID_SUPPORT=y
> CONFIG_HID=y
> # CONFIG_HID_DEBUG is not set
> # CONFIG_HIDRAW is not set
>
> #
> # USB Input Devices
> #
> CONFIG_USB_HID=y
> # CONFIG_USB_HIDINPUT_POWERBOOK is not set
> # CONFIG_HID_FF is not set
> CONFIG_USB_HIDDEV=y
> CONFIG_USB_SUPPORT=y
> CONFIG_USB_ARCH_HAS_HCD=y
> CONFIG_USB_ARCH_HAS_OHCI=y
> CONFIG_USB_ARCH_HAS_EHCI=y
> CONFIG_USB=y
> # CONFIG_USB_DEBUG is not set
>
> #
> # Miscellaneous USB options
> #
> CONFIG_USB_DEVICEFS=y
> # CONFIG_USB_DEVICE_CLASS is not set
> # CONFIG_USB_DYNAMIC_MINORS is not set
> # CONFIG_USB_OTG is not set
>
> #
> # USB Host Controller Drivers
> #
> CONFIG_USB_EHCI_HCD=y
> # CONFIG_USB_EHCI_SPLIT_ISO is not set
> # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
> CONFIG_USB_EHCI_TT_NEWSCHED=y
> # CONFIG_USB_ISP116X_HCD is not set
> CONFIG_USB_OHCI_HCD=y
> CONFIG_USB_OHCI_HCD_PPC_OF=y
> CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
> # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
> CONFIG_USB_OHCI_HCD_PCI=y
> CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
> CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
> CONFIG_USB_OHCI_LITTLE_ENDIAN=y
> # CONFIG_USB_UHCI_HCD is not set
> # CONFIG_USB_SL811_HCD is not set
> # CONFIG_USB_R8A66597_HCD is not set
>
> #
> # USB Device Class drivers
> #
> # CONFIG_USB_ACM is not set
> # CONFIG_USB_PRINTER is not set
>
> #
> # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
> #
>
> #
> # may also be needed; see USB_STORAGE Help for more information
> #
> CONFIG_USB_STORAGE=m
> # CONFIG_USB_STORAGE_DEBUG is not set
> # CONFIG_USB_STORAGE_DATAFAB is not set
> # CONFIG_USB_STORAGE_FREECOM is not set
> # CONFIG_USB_STORAGE_ISD200 is not set
> # CONFIG_USB_STORAGE_DPCM is not set
> # CONFIG_USB_STORAGE_USBAT is not set
> # CONFIG_USB_STORAGE_SDDR09 is not set
> # CONFIG_USB_STORAGE_SDDR55 is not set
> # CONFIG_USB_STORAGE_JUMPSHOT is not set
> # CONFIG_USB_STORAGE_ALAUDA is not set
> # CONFIG_USB_STORAGE_ONETOUCH is not set
> # CONFIG_USB_STORAGE_KARMA is not set
> # CONFIG_USB_LIBUSUAL is not set
>
> #
> # USB Imaging devices
> #
> # CONFIG_USB_MDC800 is not set
> # CONFIG_USB_MICROTEK is not set
> # CONFIG_USB_MON is not set
>
> #
> # USB port drivers
> #
>
> #
> # USB Serial Converter support
> #
> # CONFIG_USB_SERIAL is not set
>
> #
> # USB Miscellaneous drivers
> #
> # CONFIG_USB_EMI62 is not set
> # CONFIG_USB_EMI26 is not set
> # CONFIG_USB_ADUTUX is not set
> # CONFIG_USB_AUERSWALD is not set
> # CONFIG_USB_RIO500 is not set
> # CONFIG_USB_LEGOTOWER is not set
> # CONFIG_USB_LCD is not set
> # CONFIG_USB_BERRY_CHARGE is not set
> # CONFIG_USB_LED is not set
> # CONFIG_USB_CYPRESS_CY7C63 is not set
> # CONFIG_USB_CYTHERM is not set
> # CONFIG_USB_PHIDGET is not set
> # CONFIG_USB_IDMOUSE is not set
> # CONFIG_USB_FTDI_ELAN is not set
> CONFIG_USB_APPLEDISPLAY=m
> # CONFIG_USB_SISUSBVGA is not set
> # CONFIG_USB_LD is not set
> # CONFIG_USB_TRANCEVIBRATOR is not set
> # CONFIG_USB_IOWARRIOR is not set
> # CONFIG_USB_TEST is not set
> # CONFIG_USB_GOTEMP is not set
>
> #
> # USB DSL modem support
> #
>
> #
> # USB Gadget Support
> #
> # CONFIG_USB_GADGET is not set
> # CONFIG_MMC is not set
> # CONFIG_NEW_LEDS is not set
> CONFIG_INFINIBAND=m
> # CONFIG_INFINIBAND_USER_MAD is not set
> # CONFIG_INFINIBAND_USER_ACCESS is not set
> CONFIG_INFINIBAND_ADDR_TRANS=y
> CONFIG_INFINIBAND_MTHCA=m
> CONFIG_INFINIBAND_MTHCA_DEBUG=y
> # CONFIG_INFINIBAND_AMSO1100 is not set
> # CONFIG_MLX4_INFINIBAND is not set
> CONFIG_INFINIBAND_IPOIB=m
> # CONFIG_INFINIBAND_IPOIB_CM is not set
> CONFIG_INFINIBAND_IPOIB_DEBUG=y
> # CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
> # CONFIG_INFINIBAND_SRP is not set
> CONFIG_INFINIBAND_ISER=m
> # CONFIG_EDAC is not set
> # CONFIG_RTC_CLASS is not set
> CONFIG_DCA=m
>
> #
> # Userspace I/O
> #
> # CONFIG_UIO is not set
>
> #
> # File systems
> #
> CONFIG_EXT2_FS=y
> CONFIG_EXT2_FS_XATTR=y
> CONFIG_EXT2_FS_POSIX_ACL=y
> CONFIG_EXT2_FS_SECURITY=y
> CONFIG_EXT2_FS_XIP=y
> CONFIG_FS_XIP=y
> CONFIG_EXT3_FS=y
> CONFIG_EXT3_FS_XATTR=y
> CONFIG_EXT3_FS_POSIX_ACL=y
> CONFIG_EXT3_FS_SECURITY=y
> # CONFIG_EXT4DEV_FS is not set
> CONFIG_JBD=y
> # CONFIG_JBD_DEBUG is not set
> CONFIG_FS_MBCACHE=y
> # CONFIG_REISER4_FS is not set
> CONFIG_REISERFS_FS=y
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_REISERFS_PROC_INFO is not set
> CONFIG_REISERFS_FS_XATTR=y
> CONFIG_REISERFS_FS_POSIX_ACL=y
> CONFIG_REISERFS_FS_SECURITY=y
> CONFIG_JFS_FS=y
> CONFIG_JFS_POSIX_ACL=y
> CONFIG_JFS_SECURITY=y
> # CONFIG_JFS_DEBUG is not set
> # CONFIG_JFS_STATISTICS is not set
> CONFIG_FS_POSIX_ACL=y
> CONFIG_XFS_FS=m
> # CONFIG_XFS_QUOTA is not set
> CONFIG_XFS_SECURITY=y
> CONFIG_XFS_POSIX_ACL=y
> # CONFIG_XFS_RT is not set
> # CONFIG_GFS2_FS is not set
> # CONFIG_OCFS2_FS is not set
> # CONFIG_MINIX_FS is not set
> # CONFIG_ROMFS_FS is not set
> CONFIG_INOTIFY=y
> CONFIG_INOTIFY_USER=y
> # CONFIG_QUOTA is not set
> CONFIG_DNOTIFY=y
> # CONFIG_AUTOFS_FS is not set
> CONFIG_AUTOFS4_FS=m
> # CONFIG_FUSE_FS is not set
>
> #
> # CD-ROM/DVD Filesystems
> #
> CONFIG_ISO9660_FS=y
> # CONFIG_JOLIET is not set
> # CONFIG_ZISOFS is not set
> CONFIG_UDF_FS=m
> CONFIG_UDF_NLS=y
>
> #
> # DOS/FAT/NT Filesystems
> #
> CONFIG_FAT_FS=y
> CONFIG_MSDOS_FS=y
> CONFIG_VFAT_FS=y
> CONFIG_FAT_DEFAULT_CODEPAGE=437
> CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
> # CONFIG_NTFS_FS is not set
>
> #
> # Pseudo filesystems
> #
> CONFIG_PROC_FS=y
> CONFIG_PROC_KCORE=y
> CONFIG_PROC_SYSCTL=y
> CONFIG_SYSFS=y
> CONFIG_TMPFS=y
> # CONFIG_TMPFS_POSIX_ACL is not set
> CONFIG_HUGETLBFS=y
> CONFIG_HUGETLB_PAGE=y
> CONFIG_RAMFS=y
> # CONFIG_CONFIGFS_FS is not set
>
> #
> # Layered filesystems
> #
> # CONFIG_UNION_FS is not set
>
> #
> # Miscellaneous filesystems
> #
> # CONFIG_ADFS_FS is not set
> # CONFIG_AFFS_FS is not set
> CONFIG_HFS_FS=m
> CONFIG_HFSPLUS_FS=m
> # CONFIG_BEFS_FS is not set
> # CONFIG_BFS_FS is not set
> # CONFIG_EFS_FS is not set
> CONFIG_CRAMFS=y
> # CONFIG_VXFS_FS is not set
> # CONFIG_HPFS_FS is not set
> # CONFIG_QNX4FS_FS is not set
> # CONFIG_SYSV_FS is not set
> # CONFIG_UFS_FS is not set
>
> #
> # Network File Systems
> #
> CONFIG_NFS_FS=y
> CONFIG_NFS_V3=y
> CONFIG_NFS_V3_ACL=y
> CONFIG_NFS_V4=y
> # CONFIG_NFS_DIRECTIO is not set
> CONFIG_NFSD=m
> CONFIG_NFSD_V2_ACL=y
> CONFIG_NFSD_V3=y
> CONFIG_NFSD_V3_ACL=y
> CONFIG_NFSD_V4=y
> CONFIG_NFSD_TCP=y
> CONFIG_LOCKD=y
> CONFIG_LOCKD_V4=y
> CONFIG_EXPORTFS=m
> CONFIG_NFS_ACL_SUPPORT=y
> CONFIG_NFS_COMMON=y
> CONFIG_SUNRPC=y
> CONFIG_SUNRPC_GSS=y
> # CONFIG_SUNRPC_BIND34 is not set
> CONFIG_RPCSEC_GSS_KRB5=y
> CONFIG_RPCSEC_GSS_SPKM3=m
> # CONFIG_SMB_FS is not set
> CONFIG_CIFS=m
> # CONFIG_CIFS_STATS is not set
> # CONFIG_CIFS_WEAK_PW_HASH is not set
> CONFIG_CIFS_XATTR=y
> CONFIG_CIFS_POSIX=y
> # CONFIG_CIFS_DEBUG2 is not set
> # CONFIG_CIFS_EXPERIMENTAL is not set
> # CONFIG_NCP_FS is not set
> # CONFIG_CODA_FS is not set
> # CONFIG_AFS_FS is not set
>
> #
> # Partition Types
> #
> CONFIG_PARTITION_ADVANCED=y
> # CONFIG_ACORN_PARTITION is not set
> # CONFIG_OSF_PARTITION is not set
> # CONFIG_AMIGA_PARTITION is not set
> # CONFIG_ATARI_PARTITION is not set
> CONFIG_MAC_PARTITION=y
> CONFIG_MSDOS_PARTITION=y
> # CONFIG_BSD_DISKLABEL is not set
> # CONFIG_MINIX_SUBPARTITION is not set
> # CONFIG_SOLARIS_X86_PARTITION is not set
> # CONFIG_UNIXWARE_DISKLABEL is not set
> # CONFIG_LDM_PARTITION is not set
> # CONFIG_SGI_PARTITION is not set
> # CONFIG_ULTRIX_PARTITION is not set
> # CONFIG_SUN_PARTITION is not set
> # CONFIG_KARMA_PARTITION is not set
> # CONFIG_EFI_PARTITION is not set
> # CONFIG_SYSV68_PARTITION is not set
>
> #
> # Native Language Support
> #
> CONFIG_NLS=y
> CONFIG_NLS_DEFAULT="iso8859-1"
> CONFIG_NLS_CODEPAGE_437=y
> CONFIG_NLS_CODEPAGE_737=m
> CONFIG_NLS_CODEPAGE_775=m
> CONFIG_NLS_CODEPAGE_850=m
> CONFIG_NLS_CODEPAGE_852=m
> CONFIG_NLS_CODEPAGE_855=m
> CONFIG_NLS_CODEPAGE_857=m
> CONFIG_NLS_CODEPAGE_860=m
> CONFIG_NLS_CODEPAGE_861=m
> CONFIG_NLS_CODEPAGE_862=m
> CONFIG_NLS_CODEPAGE_863=m
> CONFIG_NLS_CODEPAGE_864=m
> CONFIG_NLS_CODEPAGE_865=m
> CONFIG_NLS_CODEPAGE_866=m
> CONFIG_NLS_CODEPAGE_869=m
> CONFIG_NLS_CODEPAGE_936=m
> CONFIG_NLS_CODEPAGE_950=m
> CONFIG_NLS_CODEPAGE_932=m
> CONFIG_NLS_CODEPAGE_949=m
> CONFIG_NLS_CODEPAGE_874=m
> CONFIG_NLS_ISO8859_8=m
> CONFIG_NLS_CODEPAGE_1250=m
> CONFIG_NLS_CODEPAGE_1251=m
> CONFIG_NLS_ASCII=m
> CONFIG_NLS_ISO8859_1=y
> CONFIG_NLS_ISO8859_2=m
> CONFIG_NLS_ISO8859_3=m
> CONFIG_NLS_ISO8859_4=m
> CONFIG_NLS_ISO8859_5=m
> CONFIG_NLS_ISO8859_6=m
> CONFIG_NLS_ISO8859_7=m
> CONFIG_NLS_ISO8859_9=m
> CONFIG_NLS_ISO8859_13=m
> CONFIG_NLS_ISO8859_14=m
> CONFIG_NLS_ISO8859_15=m
> CONFIG_NLS_KOI8_R=m
> CONFIG_NLS_KOI8_U=m
> CONFIG_NLS_UTF8=m
>
> #
> # Distributed Lock Manager
> #
> # CONFIG_DLM is not set
> # CONFIG_UCC_SLOW is not set
>
> #
> # Library routines
> #
> CONFIG_BITREVERSE=y
> CONFIG_CRC_CCITT=m
> # CONFIG_CRC16 is not set
> # CONFIG_CRC_ITU_T is not set
> CONFIG_CRC32=y
> # CONFIG_CRC7 is not set
> CONFIG_LIBCRC32C=m
> CONFIG_ZLIB_INFLATE=y
> CONFIG_ZLIB_DEFLATE=m
> CONFIG_TEXTSEARCH=y
> CONFIG_TEXTSEARCH_KMP=m
> CONFIG_PLIST=y
> CONFIG_HAS_IOMEM=y
> CONFIG_HAS_IOPORT=y
> CONFIG_HAS_DMA=y
>
> #
> # Instrumentation Support
> #
> CONFIG_PROFILING=y
> CONFIG_OPROFILE=y
> # CONFIG_KPROBES is not set
>
> #
> # Kernel hacking
> #
> # CONFIG_PRINTK_TIME is not set
> CONFIG_ENABLE_MUST_CHECK=y
> CONFIG_MAGIC_SYSRQ=y
> # CONFIG_UNUSED_SYMBOLS is not set
> # CONFIG_PAGE_OWNER is not set
> CONFIG_DEBUG_FS=y
> # CONFIG_HEADERS_CHECK is not set
> CONFIG_DEBUG_KERNEL=y
> # CONFIG_DEBUG_SHIRQ is not set
> CONFIG_DETECT_SOFTLOCKUP=y
> CONFIG_SCHED_DEBUG=y
> # CONFIG_SCHEDSTATS is not set
> # CONFIG_TIMER_STATS is not set
> # CONFIG_DEBUG_SLAB is not set
> # CONFIG_DEBUG_RT_MUTEXES is not set
> # CONFIG_RT_MUTEX_TESTER is not set
> # CONFIG_DEBUG_SPINLOCK is not set
> CONFIG_DEBUG_MUTEXES=y
> # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
> # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
> # CONFIG_DEBUG_KOBJECT is not set
> CONFIG_DEBUG_BUGVERBOSE=y
> # CONFIG_DEBUG_INFO is not set
> # CONFIG_DEBUG_VM is not set
> # CONFIG_DEBUG_LIST is not set
> # CONFIG_PROFILE_LIKELY is not set
> CONFIG_FORCED_INLINING=y
> # CONFIG_BOOT_PRINTK_DELAY is not set
> # CONFIG_DEBUG_SYNCHRO_TEST is not set
> # CONFIG_RCU_TORTURE_TEST is not set
> # CONFIG_FAULT_INJECTION is not set
> # CONFIG_WANT_EXTRA_DEBUG_INFORMATION is not set
> # CONFIG_UNWIND_INFO is not set
> # CONFIG_KGDB is not set
> CONFIG_DEBUG_STACKOVERFLOW=y
> CONFIG_DEBUG_STACK_USAGE=y
> # CONFIG_DEBUG_PAGEALLOC is not set
> # CONFIG_HCALL_STATS is not set
> CONFIG_XMON=y
> # CONFIG_XMON_DEFAULT is not set
> CONFIG_XMON_DISASSEMBLY=y
> CONFIG_DEBUGGER=y
> CONFIG_IRQSTACKS=y
> CONFIG_BOOTX_TEXT=y
> # CONFIG_PPC_EARLY_DEBUG is not set
>
> #
> # Security options
> #
> # CONFIG_KEYS is not set
> # CONFIG_SECURITY is not set
> # CONFIG_SECURITY_FILE_CAPABILITIES is not set
> CONFIG_XOR_BLOCKS=y
> CONFIG_ASYNC_CORE=y
> CONFIG_ASYNC_MEMCPY=y
> CONFIG_ASYNC_XOR=y
> CONFIG_CRYPTO=y
> CONFIG_CRYPTO_ALGAPI=y
> CONFIG_CRYPTO_BLKCIPHER=y
> CONFIG_CRYPTO_HASH=y
> CONFIG_CRYPTO_MANAGER=y
> CONFIG_CRYPTO_HMAC=y
> # CONFIG_CRYPTO_XCBC is not set
> CONFIG_CRYPTO_NULL=m
> CONFIG_CRYPTO_MD4=m
> CONFIG_CRYPTO_MD5=y
> CONFIG_CRYPTO_SHA1=m
> CONFIG_CRYPTO_SHA256=m
> CONFIG_CRYPTO_SHA512=m
> CONFIG_CRYPTO_WP512=m
> CONFIG_CRYPTO_TGR192=m
> # CONFIG_CRYPTO_GF128MUL is not set
> CONFIG_CRYPTO_ECB=m
> CONFIG_CRYPTO_CBC=y
> CONFIG_CRYPTO_PCBC=m
> # CONFIG_CRYPTO_LRW is not set
> # CONFIG_CRYPTO_CRYPTD is not set
> CONFIG_CRYPTO_DES=y
> # CONFIG_CRYPTO_FCRYPT is not set
> CONFIG_CRYPTO_BLOWFISH=m
> CONFIG_CRYPTO_TWOFISH=m
> CONFIG_CRYPTO_TWOFISH_COMMON=m
> CONFIG_CRYPTO_SERPENT=m
> CONFIG_CRYPTO_AES=m
> CONFIG_CRYPTO_CAST5=m
> CONFIG_CRYPTO_CAST6=m
> CONFIG_CRYPTO_TEA=m
> CONFIG_CRYPTO_ARC4=m
> CONFIG_CRYPTO_KHAZAD=m
> CONFIG_CRYPTO_ANUBIS=m
> CONFIG_CRYPTO_DEFLATE=m
> CONFIG_CRYPTO_MICHAEL_MIC=m
> CONFIG_CRYPTO_CRC32C=m
> # CONFIG_CRYPTO_CAMELLIA is not set
> CONFIG_CRYPTO_TEST=m
> CONFIG_CRYPTO_HW=y
>
> --------------000300070303050202020703
> Content-Type: text/plain; charset="us-ascii"
> MIME-Version: 1.0
> Content-Transfer-Encoding: 7bit
> Content-Disposition: inline
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
> --------------000300070303050202020703--
>
^ permalink raw reply
* some question about linux kernel in embed system
From: 李明 @ 2007-08-17 2:58 UTC (permalink / raw)
To: linuxppc-embedded
In-Reply-To: <200708171028495734596@taicom.com.cn>
[-- Attachment #1: Type: text/plain, Size: 788 bytes --]
hello everyone
I am doing some embed system works.
Now I want to replant the linux-2.4.32 to my own system.
But there are some questions.First let me introduce my heardware:
I use powerpc+flash+sdram to buildup a mini system,use u-boot 1.1.4 as bootloader then I need to replant the kernel on it .
The linux-2.4.32 kernel which was made a uImage, is running in this mini system, the question is appear:
Image Name: Linux-2.4.32
Created: 2007-08-16 21:31:03 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 685809 Bytes = 669.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
then the kernel is dead, I do not know what is problem,please give me some clew,thanks!
[-- Attachment #2: man_016(08-17-10-55-25).gif --]
[-- Type: image/gif, Size: 1729 bytes --]
^ permalink raw reply
* [PATCH] fix compile warning in arch/powerpc/kernel/sysfs.c
From: Michael Neuling @ 2007-08-17 3:40 UTC (permalink / raw)
To: paulus; +Cc: linuxppc-dev
This fixes the following warning:
arch/powerpc/kernel/sysfs.c:388: warning: ignoring return value of
'sysfs_create_group', declared with attribute warn_unused_result
Signed-off-by: Michael Neuling <mikey@neuling.org>
---
arch/powerpc/kernel/sysfs.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
Index: linux-2.6-ozlabs/arch/powerpc/kernel/sysfs.c
===================================================================
--- linux-2.6-ozlabs.orig/arch/powerpc/kernel/sysfs.c
+++ linux-2.6-ozlabs/arch/powerpc/kernel/sysfs.c
@@ -378,14 +378,18 @@ EXPORT_SYMBOL_GPL(cpu_add_sysdev_attr);
int cpu_add_sysdev_attr_group(struct attribute_group *attrs)
{
- int cpu;
+ int cpu, err;
struct sys_device *sysdev;
mutex_lock(&cpu_mutex);
for_each_possible_cpu(cpu) {
sysdev = get_cpu_sysdev(cpu);
- sysfs_create_group(&sysdev->kobj, attrs);
+ err = sysfs_create_group(&sysdev->kobj, attrs);
+ if (err) {
+ mutex_unlock(&cpu_mutex);
+ return err;
+ }
}
mutex_unlock(&cpu_mutex);
^ permalink raw reply
* Re: Machine automagically reboots with 2.6.23-rc2-mm2
From: Balbir Singh @ 2007-08-17 4:37 UTC (permalink / raw)
To: Michael Neuling; +Cc: linuxppc-dev, Andrew Morton, linux kernel mailing list
In-Reply-To: <30255.1187317044@neuling.org>
Michael Neuling wrote:
>
> SLB shadow was bust. Make sure you have
> edd0622bd2e8f755c960827e15aa6908c3c5aa94
>
> [POWERPC] Fix potential duplicate entry in SLB shadow buffer
>
> We were getting a duplicate entry in the SLB shadow buffer in
> slb_flush_and_rebolt() if the kernel stack was in the same segment
> as PAGE_OFFSET, which on POWER6 causes the hypervisor to terminate
> the partition with an error. This fixes it.
>
> Also we were not creating an SLB entry (or an SLB shadow buffer
> entry) for the kernel stack on secondary CPUs when starting the
> CPU. This isn't a major problem, since an appropriate entry will
> be created on demand, but this fixes that also for consistency.
>
> Signed-off-by: Paul Mackerras <paulus@samba.org>
>
Thanks for pointing that out, I'll get the fix and retry.
Balbir Singh.
^ permalink raw reply
* Re: [PATCH 1/2] Add scaled time to taskstats based process accounting
From: Balbir Singh @ 2007-08-17 4:47 UTC (permalink / raw)
To: Michael Neuling; +Cc: Andrew Morton, linuxppc-dev, Paul Mackerras, linux-kernel
In-Reply-To: <13529.1187310208@neuling.org>
Michael Neuling wrote:
>> I'd also request for you to add a cpu_scaled_run_real_total for use
>> by delay accounting. cpu_scaled_run_real_total should be similar in
>> functionality to cpu_run_real_total.
>
> Will do. Should I add cpu_scaled_run_real_total to the end of the
> struct taskstat, or next to cpu_run_real_total?
>
Please add it to the end, that helps maintain binary compatibility
across all versions of taskstats.
>>> /* Note: this timer irq context must be accounted for as well. */
>>> - if (user_tick)
>>> + if (user_tick) {
>>> account_user_time(p, jiffies_to_cputime(1));
>>> - else
>>> + account_user_time_scaled(p, jiffies_to_cputime(1));
>>> + } else {
>>> account_system_time(p, HARDIRQ_OFFSET, jiffies_to_cputime(1));
>>> + account_system_time_scaled(p, jiffies_to_cputime(1));
>>> + }
>> I am a little confused here, scaled accounting and regular accounting
>> go hand in hand?
>
> We need to account for scaled and normal time in this generic code.
> All other calls to account_(user|system)_time are in arch code.
>
So the assumption here is that we ran at full frequency during
this time, is my understanding correct?
--
Warm Regards,
Balbir Singh
Linux Technology Center
IBM, ISTL
^ permalink raw reply
* [PATCH] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
From: Olof Johansson @ 2007-08-17 3:57 UTC (permalink / raw)
To: paulus; +Cc: linuxppc-dev
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Index: linux-2.6/arch/powerpc/platforms/pasemi/iommu.c
===================================================================
--- linux-2.6.orig/arch/powerpc/platforms/pasemi/iommu.c
+++ linux-2.6/arch/powerpc/platforms/pasemi/iommu.c
@@ -93,7 +93,7 @@ static void iobmap_build(struct iommu_ta
pr_debug("iobmap: build at: %lx, %lx, addr: %lx\n", index, npages, uaddr);
- bus_addr = (tbl->it_offset + index) << PAGE_SHIFT;
+ bus_addr = (tbl->it_offset + index) << IOBMAP_PAGE_SHIFT;
ip = ((u32 *)tbl->it_base) + index;
@@ -118,7 +118,7 @@ static void iobmap_free(struct iommu_tab
pr_debug("iobmap: free at: %lx, %lx\n", index, npages);
- bus_addr = (tbl->it_offset + index) << PAGE_SHIFT;
+ bus_addr = (tbl->it_offset + index) << IOBMAP_PAGE_SHIFT;
ip = ((u32 *)tbl->it_base) + index;
@@ -137,7 +137,7 @@ static void iommu_table_iobmap_setup(voi
iommu_table_iobmap.it_busno = 0;
iommu_table_iobmap.it_offset = 0;
/* it_size is in number of entries */
- iommu_table_iobmap.it_size = 0x80000000 >> PAGE_SHIFT;
+ iommu_table_iobmap.it_size = 0x80000000 >> IOBMAP_PAGE_SHIFT;
/* Initialize the common IOMMU code */
iommu_table_iobmap.it_base = (unsigned long)iob_l2_base;
^ permalink raw reply
* Re: [PATCH 1/2] Add scaled time to taskstats based process accounting
From: Michael Neuling @ 2007-08-17 4:56 UTC (permalink / raw)
To: balbir; +Cc: Andrew Morton, linuxppc-dev, Paul Mackerras, linux-kernel
In-Reply-To: <46C52872.9060408@linux.vnet.ibm.com>
In message <46C52872.9060408@linux.vnet.ibm.com> you wrote:
> Michael Neuling wrote:
> >> I'd also request for you to add a cpu_scaled_run_real_total for use
> >> by delay accounting. cpu_scaled_run_real_total should be similar in
> >> functionality to cpu_run_real_total.
> >
> > Will do. Should I add cpu_scaled_run_real_total to the end of the
> > struct taskstat, or next to cpu_run_real_total?
> >
>
> Please add it to the end, that helps maintain binary compatibility
> across all versions of taskstats.
OK
>
> >>> /* Note: this timer irq context must be accounted for as well. */
> >>> - if (user_tick)
> >>> + if (user_tick) {
> >>> account_user_time(p, jiffies_to_cputime(1));
> >>> - else
> >>> + account_user_time_scaled(p, jiffies_to_cputime(1));
> >>> + } else {
> >>> account_system_time(p, HARDIRQ_OFFSET, jiffies_to_cputime(1));
> >>> + account_system_time_scaled(p, jiffies_to_cputime(1));
> >>> + }
> >> I am a little confused here, scaled accounting and regular accounting
> >> go hand in hand?
> >
> > We need to account for scaled and normal time in this generic code.
> > All other calls to account_(user|system)_time are in arch code.
> >
>
> So the assumption here is that we ran at full frequency during
> this time, is my understanding correct?
Yes.
I guess we could keep a per CPU last scaling factor for this case
(similar to what we are storing in the POWERPC paca)
Mikey
^ permalink raw reply
* Please pull from 'fixes-2.6.23' branch
From: Kumar Gala @ 2007-08-17 5:02 UTC (permalink / raw)
To: Paul Mackerras; +Cc: linuxppc-dev
Please pull from 'fixes-2.6.23' branch of
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc.git fixes-2.6.23
to receive the following updates:
arch/powerpc/boot/dts/mpc8544ds.dts | 88 ++++------
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 114 ++----------
arch/powerpc/kernel/traps.c | 4
arch/powerpc/platforms/85xx/Kconfig | 1
arch/powerpc/platforms/85xx/mpc8544_ds.c | 214 +-----------------------
arch/powerpc/platforms/86xx/Kconfig | 1
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 224 +------------------------
arch/powerpc/platforms/Kconfig | 8
arch/powerpc/platforms/Makefile | 3
arch/powerpc/platforms/fsl_uli1575.c | 255 +++++++++++++++++++++++++++++
arch/powerpc/sysdev/rtc_cmos_setup.c | 15 +
include/asm-powerpc/reg_booke.h | 12 +
12 files changed, 386 insertions(+), 553 deletions(-)
Becky Bruce (1):
[POWERPC] Fix FSL BookE machine check reporting
Kumar Gala (2):
[POWERPC] Add interrupt resource for RTC CMOS driver
[POWERPC] Fix interrupt routing and setup of ULI M1575 on FSL boards
^ permalink raw reply
* [PATCH] [POWERPC] Add interrupt resource for RTC CMOS driver
From: Kumar Gala @ 2007-08-17 5:03 UTC (permalink / raw)
To: linuxppc-dev
The RTC CMOS driver expects the interrupt to be a resource of the platform
device. Use a fixed interrupt value of 8 since on PPC if we are using this
its off an i8259 which we ensure has interrupt numbers 0..15.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/sysdev/rtc_cmos_setup.c | 15 +++++++++++----
1 files changed, 11 insertions(+), 4 deletions(-)
diff --git a/arch/powerpc/sysdev/rtc_cmos_setup.c b/arch/powerpc/sysdev/rtc_cmos_setup.c
index e276048..1d2be7d 100644
--- a/arch/powerpc/sysdev/rtc_cmos_setup.c
+++ b/arch/powerpc/sysdev/rtc_cmos_setup.c
@@ -20,14 +20,16 @@ static int __init add_rtc(void)
{
struct device_node *np;
struct platform_device *pd;
- struct resource res;
+ struct resource res[2];
int ret;
+ memset(&res, 0, sizeof(res));
+
np = of_find_compatible_node(NULL, NULL, "pnpPNP,b00");
if (!np)
return -ENODEV;
- ret = of_address_to_resource(np, 0, &res);
+ ret = of_address_to_resource(np, 0, &res[0]);
of_node_put(np);
if (ret)
return ret;
@@ -36,11 +38,16 @@ static int __init add_rtc(void)
* RTC_PORT(x) is hardcoded in asm/mc146818rtc.h. Verify that the
* address provided by the device node matches.
*/
- if (res.start != RTC_PORT(0))
+ if (res[0].start != RTC_PORT(0))
return -EINVAL;
+ res[1].start = 8;
+ res[1].end = 8;
+ res[1].flags = IORESOURCE_IRQ;
+
pd = platform_device_register_simple("rtc_cmos", -1,
- &res, 1);
+ &res[0], 2);
+
if (IS_ERR(pd))
return PTR_ERR(pd);
--
1.5.2.2
^ permalink raw reply related
* [PATCH] [POWERPC] Fix interrupt routing and setup of ULI M1575 on FSL boards
From: Kumar Gala @ 2007-08-17 5:03 UTC (permalink / raw)
To: linuxppc-dev
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/boot/dts/mpc8544ds.dts | 88 ++++------
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 114 +++----------
arch/powerpc/platforms/85xx/Kconfig | 1 +
arch/powerpc/platforms/85xx/mpc8544_ds.c | 214 ++----------------------
arch/powerpc/platforms/86xx/Kconfig | 1 +
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 224 ++-----------------------
arch/powerpc/platforms/Kconfig | 8 +
arch/powerpc/platforms/Makefile | 3 +
arch/powerpc/platforms/fsl_uli1575.c | 255 ++++++++++++++++++++++++++++
9 files changed, 363 insertions(+), 545 deletions(-)
create mode 100644 arch/powerpc/platforms/fsl_uli1575.c
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 4680e20..3e79bf0 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -44,8 +44,18 @@
#size-cells = <1>;
#interrupt-cells = <2>;
device_type = "soc";
- ranges = <0 e0000000 00100000>;
- reg = <e0000000 00100000>; // CCSRBAR 1M
+
+
+ ranges = <00001000 e0001000 000ff000
+ 80000000 80000000 20000000
+ a0000000 a0000000 10000000
+ b0000000 b0000000 00100000
+ c0000000 c0000000 20000000
+ b0100000 b0100000 00100000
+ e1000000 e1000000 00010000
+ e1010000 e1010000 00010000
+ e1020000 e1020000 00010000>;
+ reg = <e0000000 00001000>; // CCSRBAR 1M
bus-frequency = <0>; // Filled out by uboot.
memory-controller@2000 {
@@ -161,8 +171,8 @@
interrupt-parent = <&mpic>;
interrupts = <18 2>;
bus-range = <0 ff>;
- ranges = <02000000 0 80000000 80000000 0 10000000
- 01000000 0 00000000 e2000000 0 00800000>;
+ ranges = <02000000 0 c0000000 c0000000 0 20000000
+ 01000000 0 00000000 e1000000 0 00010000>;
clock-frequency = <3f940aa>;
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -178,8 +188,8 @@
#address-cells = <3>;
reg = <9000 1000>;
bus-range = <0 ff>;
- ranges = <02000000 0 90000000 90000000 0 10000000
- 01000000 0 00000000 e3000000 0 00800000>;
+ ranges = <02000000 0 80000000 80000000 0 20000000
+ 01000000 0 00000000 e1010000 0 00010000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1a 2>;
@@ -202,7 +212,7 @@
reg = <a000 1000>;
bus-range = <0 ff>;
ranges = <02000000 0 a0000000 a0000000 0 10000000
- 01000000 0 00000000 e2800000 0 00800000>;
+ 01000000 0 00000000 e1020000 0 00010000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <19 2>;
@@ -224,49 +234,29 @@
#address-cells = <3>;
reg = <b000 1000>;
bus-range = <0 ff>;
- ranges = <02000000 0 b0000000 b0000000 0 10000000
- 01000000 0 00000000 e3800000 0 00800000>;
+ ranges = <02000000 0 b0000000 b0000000 0 00100000
+ 01000000 0 00000000 b0100000 0 00100000>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1b 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <fb00 0 0 0>;
interrupt-map = <
-
- // IDSEL 0x1a
- d000 0 0 1 &i8259 6 2
- d000 0 0 2 &i8259 3 2
- d000 0 0 3 &i8259 4 2
- d000 0 0 4 &i8259 5 2
-
- // IDSEL 0x1b
- d800 0 0 1 &i8259 5 2
- d800 0 0 2 &i8259 0 0
- d800 0 0 3 &i8259 0 0
- d800 0 0 4 &i8259 0 0
-
// IDSEL 0x1c USB
- e000 0 0 1 &i8259 9 2
- e000 0 0 2 &i8259 a 2
- e000 0 0 3 &i8259 c 2
- e000 0 0 4 &i8259 7 2
+ e000 0 0 0 &i8259 c 2
+ e100 0 0 0 &i8259 9 2
+ e200 0 0 0 &i8259 a 2
+ e300 0 0 0 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 1 &i8259 9 2
- e800 0 0 2 &i8259 a 2
- e800 0 0 3 &i8259 b 2
- e800 0 0 4 &i8259 0 0
+ e800 0 0 0 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 1 &i8259 c 2
- f000 0 0 2 &i8259 0 0
- f000 0 0 3 &i8259 0 0
- f000 0 0 4 &i8259 0 0
+ f000 0 0 0 &i8259 7 2
+ f100 0 0 0 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 1 &i8259 6 2
- f800 0 0 2 &i8259 0 0
- f800 0 0 3 &i8259 0 0
- f800 0 0 4 &i8259 0 0
+ f800 0 0 0 &i8259 e 2
+ f900 0 0 0 &i8259 5 2
>;
uli1575@0 {
reg = <0 0 0 0 0>;
@@ -274,10 +264,10 @@
#address-cells = <3>;
ranges = <02000000 0 b0000000
02000000 0 b0000000
- 0 10000000
+ 0 00100000
01000000 0 00000000
01000000 0 00000000
- 0 00080000>;
+ 0 00100000>;
pci_bridge@0 {
reg = <0 0 0 0 0>;
@@ -285,10 +275,10 @@
#address-cells = <3>;
ranges = <02000000 0 b0000000
02000000 0 b0000000
- 0 20000000
+ 0 00100000
01000000 0 00000000
01000000 0 00000000
- 0 00100000>;
+ 0 00100000>;
isa@1e {
device_type = "isa";
@@ -296,7 +286,8 @@
#size-cells = <1>;
#address-cells = <2>;
reg = <f000 0 0 0 0>;
- ranges = <1 0 01000000 0 0
+ ranges = <1 0
+ 01000000 0 0
00001000>;
interrupt-parent = <&i8259>;
@@ -312,8 +303,7 @@
built-in;
compatible = "chrp,iic";
interrupts = <9 2>;
- interrupt-parent =
- <&mpic>;
+ interrupt-parent = <&mpic>;
};
i8042@60 {
@@ -321,8 +311,7 @@
#address-cells = <1>;
reg = <1 60 1 1 64 1>;
interrupts = <1 3 c 3>;
- interrupt-parent =
- <&i8259>;
+ interrupt-parent = <&i8259>;
keyboard@0 {
reg = <0>;
@@ -336,8 +325,7 @@
};
rtc@70 {
- compatible =
- "pnpPNP,b00";
+ compatible = "pnpPNP,b00";
reg = <1 70 2>;
};
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 5d82709..b0166e5 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -224,98 +224,36 @@
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <f800 0 0 7>;
+ interrupt-map-mask = <fb00 0 0 0>;
interrupt-map = <
/* IDSEL 0x11 */
- 8800 0 0 1 &i8259 3 2
- 8800 0 0 2 &i8259 4 2
- 8800 0 0 3 &i8259 5 2
- 8800 0 0 4 &i8259 6 2
+ 8800 0 0 1 &i8259 9 2
+ 8800 0 0 2 &i8259 a 2
+ 8800 0 0 3 &i8259 b 2
+ 8800 0 0 4 &i8259 c 2
/* IDSEL 0x12 */
- 9000 0 0 1 &i8259 4 2
- 9000 0 0 2 &i8259 5 2
- 9000 0 0 3 &i8259 6 2
- 9000 0 0 4 &i8259 3 2
-
- /* IDSEL 0x13 */
- 9800 0 0 1 &i8259 0 0
- 9800 0 0 2 &i8259 0 0
- 9800 0 0 3 &i8259 0 0
- 9800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x14 */
- a000 0 0 1 &i8259 0 0
- a000 0 0 2 &i8259 0 0
- a000 0 0 3 &i8259 0 0
- a000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x15 */
- a800 0 0 1 &i8259 0 0
- a800 0 0 2 &i8259 0 0
- a800 0 0 3 &i8259 0 0
- a800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x16 */
- b000 0 0 1 &i8259 0 0
- b000 0 0 2 &i8259 0 0
- b000 0 0 3 &i8259 0 0
- b000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x17 */
- b800 0 0 1 &i8259 0 0
- b800 0 0 2 &i8259 0 0
- b800 0 0 3 &i8259 0 0
- b800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x18 */
- c000 0 0 1 &i8259 0 0
- c000 0 0 2 &i8259 0 0
- c000 0 0 3 &i8259 0 0
- c000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x19 */
- c800 0 0 1 &i8259 0 0
- c800 0 0 2 &i8259 0 0
- c800 0 0 3 &i8259 0 0
- c800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1a */
- d000 0 0 1 &i8259 6 2
- d000 0 0 2 &i8259 3 2
- d000 0 0 3 &i8259 4 2
- d000 0 0 4 &i8259 5 2
-
-
- /* IDSEL 0x1b */
- d800 0 0 1 &i8259 5 2
- d800 0 0 2 &i8259 0 0
- d800 0 0 3 &i8259 0 0
- d800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1c */
- e000 0 0 1 &i8259 9 2
- e000 0 0 2 &i8259 a 2
- e000 0 0 3 &i8259 c 2
- e000 0 0 4 &i8259 7 2
-
- /* IDSEL 0x1d */
- e800 0 0 1 &i8259 9 2
- e800 0 0 2 &i8259 a 2
- e800 0 0 3 &i8259 b 2
- e800 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1e */
- f000 0 0 1 &i8259 c 2
- f000 0 0 2 &i8259 0 0
- f000 0 0 3 &i8259 0 0
- f000 0 0 4 &i8259 0 0
-
- /* IDSEL 0x1f */
- f800 0 0 1 &i8259 6 2
- f800 0 0 2 &i8259 0 0
- f800 0 0 3 &i8259 0 0
- f800 0 0 4 &i8259 0 0
+ 9000 0 0 1 &i8259 a 2
+ 9000 0 0 2 &i8259 b 2
+ 9000 0 0 3 &i8259 c 2
+ 9000 0 0 4 &i8259 9 2
+
+ // IDSEL 0x1c USB
+ e000 0 0 0 &i8259 c 2
+ e100 0 0 0 &i8259 9 2
+ e200 0 0 0 &i8259 a 2
+ e300 0 0 0 &i8259 b 2
+
+ // IDSEL 0x1d Audio
+ e800 0 0 0 &i8259 6 2
+
+ // IDSEL 0x1e Legacy
+ f000 0 0 0 &i8259 7 2
+ f100 0 0 0 &i8259 7 2
+
+ // IDSEL 0x1f IDE/SATA
+ f800 0 0 0 &i8259 e 2
+ f900 0 0 0 &i8259 5 2
>;
uli1575@0 {
reg = <0 0 0 0 0>;
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index f581840..f620171 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -33,6 +33,7 @@ config MPC8544_DS
bool "Freescale MPC8544 DS"
select PPC_I8259
select DEFAULT_UIMAGE
+ select FSL_ULI1575
help
This option enables support for the MPC8544 DS board
diff --git a/arch/powerpc/platforms/85xx/mpc8544_ds.c b/arch/powerpc/platforms/85xx/mpc8544_ds.c
index 4905f6f..0f834d8 100644
--- a/arch/powerpc/platforms/85xx/mpc8544_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8544_ds.c
@@ -114,211 +114,25 @@ void __init mpc8544_ds_pic_init(void)
}
#ifdef CONFIG_PCI
-enum pirq { PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH };
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn);
-/*
- * Value in table -- IRQ number
- */
-const unsigned char uli1575_irq_route_table[16] = {
- 0, /* 0: Reserved */
- 0x8,
- 0, /* 2: Reserved */
- 0x2,
- 0x4,
- 0x5,
- 0x7,
- 0x6,
- 0, /* 8: Reserved */
- 0x1,
- 0x3,
- 0x9,
- 0xb,
- 0, /* 13: Reserved */
- 0xd,
- 0xf,
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
-{
- struct of_irq oirq;
- u32 laddr[3];
- struct device_node *hosenode = hose ? hose->arch_data : NULL;
-
- if (!hosenode)
- return -EINVAL;
-
- laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
- laddr[1] = laddr[2] = 0;
- of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
- DBG("mpc8544_ds: pci irq addr %x, slot %d, pin %d, irq %d\n",
- laddr[0], slot, pin, oirq.specifier[0]);
- return oirq.specifier[0];
-}
-
-/*8259*/
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
- unsigned short temp;
- struct pci_controller *hose = pci_bus_to_host(dev->bus);
- unsigned char irq2pin[16];
- unsigned long pirq_map_word = 0;
- u32 irq;
- int i;
-
- /*
- * ULI1575 interrupts route setup
- */
- memset(irq2pin, 0, 16); /* Initialize default value 0 */
-
- irq2pin[6]=PIRQA+3; /* enabled mapping for IRQ6 to PIRQD, used by SATA */
-
- /*
- * PIRQE -> PIRQF mapping set manually
- *
- * IRQ pin IRQ#
- * PIRQE ---- 9
- * PIRQF ---- 10
- * PIRQG ---- 11
- * PIRQH ---- 12
- */
- for (i = 0; i < 4; i++)
- irq2pin[i + 9] = PIRQE + i;
-
- /* Set IRQ-PIRQ Mapping to ULI1575 */
- for (i = 0; i < 16; i++)
- if (irq2pin[i])
- pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
- << ((irq2pin[i] - PIRQA) * 4);
-
- pirq_map_word |= 1<<26; /* disable INTx in EP mode*/
-
- /* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
- DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
- (int)pirq_map_word);
- pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg) \
- do { \
- int irq; \
- irq = get_pci_irq_from_of(hose, slot, pin); \
- if (irq > 0 && irq < 16) \
- pci_write_config_byte(dev, reg, irq2pin[irq]); \
- else \
- printk(KERN_WARNING "ULI1575 device" \
- "(slot %d, pin %d) irq %d is invalid.\n", \
- slot, pin, irq); \
- } while(0)
-
- /* USB 1.1 OHCI controller 1, slot 28, pin 1 */
- ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
- /* USB 1.1 OHCI controller 2, slot 28, pin 2 */
- ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
- /* USB 1.1 OHCI controller 3, slot 28, pin 3 */
- ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
- /* USB 2.0 controller, slot 28, pin 4 */
- irq = get_pci_irq_from_of(hose, 28, 4);
- if (irq >= 0 && irq <= 15)
- pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
- /* Audio controller, slot 29, pin 1 */
- ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
- /* Modem controller, slot 29, pin 2 */
- ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
- /* HD audio controller, slot 29, pin 3 */
- ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
- /* SMB interrupt: slot 30, pin 1 */
- ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
- /* PMU ACPI SCI interrupt: slot 30, pin 2 */
- ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
- /* Serial ATA interrupt: slot 31, pin 1 */
- ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
- /* Primary PATA IDE IRQ: 14
- * Secondary PATA IDE IRQ: 15
- */
- pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
- pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
- /* Set IRQ14 and IRQ15 to legacy IRQs */
- pci_read_config_word(dev, 0x46, &temp);
- temp |= 0xc000;
- pci_write_config_word(dev, 0x46, temp);
-
- /* Set i8259 interrupt trigger
- * IRQ 3: Level
- * IRQ 4: Level
- * IRQ 5: Level
- * IRQ 6: Level
- * IRQ 7: Level
- * IRQ 9: Level
- * IRQ 10: Level
- * IRQ 11: Level
- * IRQ 12: Level
- * IRQ 14: Edge
- * IRQ 15: Edge
- */
- outb(0xfa, 0x4d0);
- outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-}
-
-/* SATA */
-static void __devinit quirk_uli5288(struct pci_dev *dev)
+static int mpc85xx_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
{
- unsigned char c;
-
- pci_read_config_byte(dev, 0x83, &c);
- c |= 0x80; /* read/write lock */
- pci_write_config_byte(dev, 0x83, c);
-
- pci_write_config_byte(dev, 0x09, 0x01); /* Base class code: storage */
- pci_write_config_byte(dev, 0x0a, 0x06); /* IDE disk */
+ struct device_node* node;
+ struct resource rsrc;
- pci_read_config_byte(dev, 0x83, &c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0x83, c);
-
- pci_read_config_byte(dev, 0x84, &c);
- c |= 0x01; /* emulated PATA mode enabled */
- pci_write_config_byte(dev, 0x84, c);
-}
+ node = (struct device_node *)hose->arch_data;
+ of_address_to_resource(node, 0, &rsrc);
-/* PATA */
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
- unsigned short temp;
- pci_write_config_word(dev, 0x04, 0x0405); /* MEM IO MSI */
- pci_read_config_word(dev, 0x4a, &temp);
- temp |= 0x1000; /* Enable Native IRQ 14/15 */
- pci_write_config_word(dev, 0x4a, temp);
-}
+ if ((rsrc.start & 0xfffff) == 0xb000) {
+ return uli_exclude_device(hose, bus, devfn);
+ }
-/*Bridge*/
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
- unsigned char temp;
- pci_write_config_word(dev, 0x04, 0x0007); /* mem access */
- pci_read_config_byte(dev, 0x7c, &temp);
- pci_write_config_byte(dev, 0x7c, 0x80); /* R/W lock control */
- pci_write_config_byte(dev, 0x09, 0x01); /* set as pci-pci bridge */
- pci_write_config_byte(dev, 0x7c, temp); /* restore pci bus debug control */
- dev->class |= 0x1;
+ return PCIBIOS_SUCCESSFUL;
}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
#endif /* CONFIG_PCI */
/*
@@ -342,6 +156,8 @@ static void __init mpc8544_ds_setup_arch(void)
else
fsl_add_bridge(np, 0);
}
+ uses_fsl_uli_m1575 = 1;
+ ppc_md.pci_exclude_device = mpc85xx_exclude_device;
#endif
printk("MPC8544 DS board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/86xx/Kconfig b/arch/powerpc/platforms/86xx/Kconfig
index 343b76d..685b2fb 100644
--- a/arch/powerpc/platforms/86xx/Kconfig
+++ b/arch/powerpc/platforms/86xx/Kconfig
@@ -7,6 +7,7 @@ config MPC8641_HPCN
bool "Freescale MPC8641 HPCN"
select PPC_I8259
select DEFAULT_UIMAGE
+ select FSL_ULI1575
help
This option enables support for the MPC8641 HPCN board.
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index e9eaa07..56b27ca 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -107,220 +107,25 @@ mpc86xx_hpcn_init_irq(void)
}
#ifdef CONFIG_PCI
+extern int uses_fsl_uli_m1575;
+extern int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn);
-enum pirq{PIRQA = 8, PIRQB, PIRQC, PIRQD, PIRQE, PIRQF, PIRQG, PIRQH};
-const unsigned char uli1575_irq_route_table[16] = {
- 0, /* 0: Reserved */
- 0x8, /* 1: 0b1000 */
- 0, /* 2: Reserved */
- 0x2, /* 3: 0b0010 */
- 0x4, /* 4: 0b0100 */
- 0x5, /* 5: 0b0101 */
- 0x7, /* 6: 0b0111 */
- 0x6, /* 7: 0b0110 */
- 0, /* 8: Reserved */
- 0x1, /* 9: 0b0001 */
- 0x3, /* 10: 0b0011 */
- 0x9, /* 11: 0b1001 */
- 0xb, /* 12: 0b1011 */
- 0, /* 13: Reserved */
- 0xd, /* 14, 0b1101 */
- 0xf, /* 15, 0b1111 */
-};
-
-static int __devinit
-get_pci_irq_from_of(struct pci_controller *hose, int slot, int pin)
-{
- struct of_irq oirq;
- u32 laddr[3];
- struct device_node *hosenode = hose ? hose->arch_data : NULL;
-
- if (!hosenode) return -EINVAL;
-
- laddr[0] = (hose->first_busno << 16) | (PCI_DEVFN(slot, 0) << 8);
- laddr[1] = laddr[2] = 0;
- of_irq_map_raw(hosenode, &pin, 1, laddr, &oirq);
- DBG("mpc86xx_hpcn: pci irq addr %x, slot %d, pin %d, irq %d\n",
- laddr[0], slot, pin, oirq.specifier[0]);
- return oirq.specifier[0];
-}
-
-static void __devinit quirk_uli1575(struct pci_dev *dev)
-{
- unsigned short temp;
- struct pci_controller *hose = pci_bus_to_host(dev->bus);
- unsigned char irq2pin[16], c;
- unsigned long pirq_map_word = 0;
- u32 irq;
- int i;
-
- /*
- * ULI1575 interrupts route setup
- */
- memset(irq2pin, 0, 16); /* Initialize default value 0 */
-
- /*
- * PIRQA -> PIRQD mapping read from OF-tree
- *
- * interrupts for PCI slot0 -- PIRQA / PIRQB / PIRQC / PIRQD
- * PCI slot1 -- PIRQB / PIRQC / PIRQD / PIRQA
- */
- for (i = 0; i < 4; i++){
- irq = get_pci_irq_from_of(hose, 17, i + 1);
- if (irq > 0 && irq < 16)
- irq2pin[irq] = PIRQA + i;
- else
- printk(KERN_WARNING "ULI1575 device"
- "(slot %d, pin %d) irq %d is invalid.\n",
- 17, i, irq);
- }
-
- /*
- * PIRQE -> PIRQF mapping set manually
- *
- * IRQ pin IRQ#
- * PIRQE ---- 9
- * PIRQF ---- 10
- * PIRQG ---- 11
- * PIRQH ---- 12
- */
- for (i = 0; i < 4; i++) irq2pin[i + 9] = PIRQE + i;
-
- /* Set IRQ-PIRQ Mapping to ULI1575 */
- for (i = 0; i < 16; i++)
- if (irq2pin[i])
- pirq_map_word |= (uli1575_irq_route_table[i] & 0xf)
- << ((irq2pin[i] - PIRQA) * 4);
-
- /* ULI1575 IRQ mapping conf register default value is 0xb9317542 */
- DBG("Setup ULI1575 IRQ mapping configuration register value = 0x%x\n",
- pirq_map_word);
- pci_write_config_dword(dev, 0x48, pirq_map_word);
-
-#define ULI1575_SET_DEV_IRQ(slot, pin, reg) \
- do { \
- int irq; \
- irq = get_pci_irq_from_of(hose, slot, pin); \
- if (irq > 0 && irq < 16) \
- pci_write_config_byte(dev, reg, irq2pin[irq]); \
- else \
- printk(KERN_WARNING "ULI1575 device" \
- "(slot %d, pin %d) irq %d is invalid.\n", \
- slot, pin, irq); \
- } while(0)
-
- /* USB 1.1 OHCI controller 1, slot 28, pin 1 */
- ULI1575_SET_DEV_IRQ(28, 1, 0x86);
-
- /* USB 1.1 OHCI controller 2, slot 28, pin 2 */
- ULI1575_SET_DEV_IRQ(28, 2, 0x87);
-
- /* USB 1.1 OHCI controller 3, slot 28, pin 3 */
- ULI1575_SET_DEV_IRQ(28, 3, 0x88);
-
- /* USB 2.0 controller, slot 28, pin 4 */
- irq = get_pci_irq_from_of(hose, 28, 4);
- if (irq >= 0 && irq <=15)
- pci_write_config_dword(dev, 0x74, uli1575_irq_route_table[irq]);
-
- /* Audio controller, slot 29, pin 1 */
- ULI1575_SET_DEV_IRQ(29, 1, 0x8a);
-
- /* Modem controller, slot 29, pin 2 */
- ULI1575_SET_DEV_IRQ(29, 2, 0x8b);
-
- /* HD audio controller, slot 29, pin 3 */
- ULI1575_SET_DEV_IRQ(29, 3, 0x8c);
-
- /* SMB interrupt: slot 30, pin 1 */
- ULI1575_SET_DEV_IRQ(30, 1, 0x8e);
-
- /* PMU ACPI SCI interrupt: slot 30, pin 2 */
- ULI1575_SET_DEV_IRQ(30, 2, 0x8f);
-
- /* Serial ATA interrupt: slot 31, pin 1 */
- ULI1575_SET_DEV_IRQ(31, 1, 0x8d);
-
- /* Primary PATA IDE IRQ: 14
- * Secondary PATA IDE IRQ: 15
- */
- pci_write_config_byte(dev, 0x44, 0x30 | uli1575_irq_route_table[14]);
- pci_write_config_byte(dev, 0x75, uli1575_irq_route_table[15]);
-
- /* Set IRQ14 and IRQ15 to legacy IRQs */
- pci_read_config_word(dev, 0x46, &temp);
- temp |= 0xc000;
- pci_write_config_word(dev, 0x46, temp);
-
- /* Set i8259 interrupt trigger
- * IRQ 3: Level
- * IRQ 4: Level
- * IRQ 5: Level
- * IRQ 6: Level
- * IRQ 7: Level
- * IRQ 9: Level
- * IRQ 10: Level
- * IRQ 11: Level
- * IRQ 12: Level
- * IRQ 14: Edge
- * IRQ 15: Edge
- */
- outb(0xfa, 0x4d0);
- outb(0x1e, 0x4d1);
-
-#undef ULI1575_SET_DEV_IRQ
-
- /* Disable the HD interface and enable the AC97 interface. */
- pci_read_config_byte(dev, 0xb8, &c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0xb8, c);
-}
-
-static void __devinit quirk_uli5288(struct pci_dev *dev)
+static int mpc86xx_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
{
- unsigned char c;
+ struct device_node* node;
+ struct resource rsrc;
- pci_read_config_byte(dev,0x83,&c);
- c |= 0x80;
- pci_write_config_byte(dev, 0x83, c);
+ node = (struct device_node *)hose->arch_data;
+ of_address_to_resource(node, 0, &rsrc);
- pci_write_config_byte(dev, 0x09, 0x01);
- pci_write_config_byte(dev, 0x0a, 0x06);
-
- pci_read_config_byte(dev,0x83,&c);
- c &= 0x7f;
- pci_write_config_byte(dev, 0x83, c);
-
- pci_read_config_byte(dev,0x84,&c);
- c |= 0x01;
- pci_write_config_byte(dev, 0x84, c);
-}
-
-static void __devinit quirk_uli5229(struct pci_dev *dev)
-{
- unsigned short temp;
- pci_write_config_word(dev, 0x04, 0x0405);
- dev->class &= ~0x5;
- pci_read_config_word(dev, 0x4a, &temp);
- temp |= 0x1000;
- pci_write_config_word(dev, 0x4a, temp);
-}
+ if ((rsrc.start & 0xfffff) == 0x8000) {
+ return uli_exclude_device(hose, bus, devfn);
+ }
-static void __devinit early_uli5249(struct pci_dev *dev)
-{
- unsigned char temp;
- pci_write_config_word(dev, 0x04, 0x0007);
- pci_read_config_byte(dev, 0x7c, &temp);
- pci_write_config_byte(dev, 0x7c, 0x80);
- pci_write_config_byte(dev, 0x09, 0x01);
- pci_write_config_byte(dev, 0x7c, temp);
- dev->class |= 0x1;
+ return PCIBIOS_SUCCESSFUL;
}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
#endif /* CONFIG_PCI */
@@ -353,6 +158,9 @@ mpc86xx_hpcn_setup_arch(void)
else
fsl_add_bridge(np, 0);
}
+ uses_fsl_uli_m1575 = 1;
+ ppc_md.pci_exclude_device = mpc86xx_exclude_device;
+
#endif
printk("MPC86xx HPCN board from Freescale Semiconductor\n");
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index 932538a..cfc2497 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -282,4 +282,12 @@ config AXON_RAM
minor numbers are available in /proc/devices, /proc/partitions or
in /sys/block/axonram?/dev.
+config FSL_ULI1575
+ bool
+ default n
+ help
+ Supports for the ULI1575 PCIe south bridge that exists on some
+ Freescale reference boards. The boards all use the ULI in pretty
+ much the same way.
+
endmenu
diff --git a/arch/powerpc/platforms/Makefile b/arch/powerpc/platforms/Makefile
index d6e041a..d44e832 100644
--- a/arch/powerpc/platforms/Makefile
+++ b/arch/powerpc/platforms/Makefile
@@ -1,3 +1,6 @@
+
+obj-$(CONFIG_FSL_ULI1575) += fsl_uli1575.o
+
ifeq ($(CONFIG_PPC_MERGE),y)
obj-$(CONFIG_PPC_PMAC) += powermac/
else
diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
new file mode 100644
index 0000000..af2321f
--- /dev/null
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -0,0 +1,255 @@
+/*
+ * ULI M1575 setup code - specific to Freescale boards
+ *
+ * Copyright 2007 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+
+#include <asm/system.h>
+#include <asm/pci-bridge.h>
+
+#define ULI_PIRQA 0x08
+#define ULI_PIRQB 0x09
+#define ULI_PIRQC 0x0a
+#define ULI_PIRQD 0x0b
+#define ULI_PIRQE 0x0c
+#define ULI_PIRQF 0x0d
+#define ULI_PIRQG 0x0e
+
+#define ULI_8259_NONE 0x00
+#define ULI_8259_IRQ1 0x08
+#define ULI_8259_IRQ3 0x02
+#define ULI_8259_IRQ4 0x04
+#define ULI_8259_IRQ5 0x05
+#define ULI_8259_IRQ6 0x07
+#define ULI_8259_IRQ7 0x06
+#define ULI_8259_IRQ9 0x01
+#define ULI_8259_IRQ10 0x03
+#define ULI_8259_IRQ11 0x09
+#define ULI_8259_IRQ12 0x0b
+#define ULI_8259_IRQ14 0x0d
+#define ULI_8259_IRQ15 0x0f
+
+u8 uli_pirq_to_irq[8] = {
+ ULI_8259_IRQ9, /* PIRQA */
+ ULI_8259_IRQ10, /* PIRQB */
+ ULI_8259_IRQ11, /* PIRQC */
+ ULI_8259_IRQ12, /* PIRQD */
+ ULI_8259_IRQ5, /* PIRQE */
+ ULI_8259_IRQ6, /* PIRQF */
+ ULI_8259_IRQ7, /* PIRQG */
+ ULI_8259_NONE, /* PIRQH */
+};
+
+/* set in board code if you want this quirks to do something */
+int uses_fsl_uli_m1575;
+
+/* Bridge */
+static void __devinit early_uli5249(struct pci_dev *dev)
+{
+ unsigned char temp;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ /* read/write lock */
+ pci_read_config_byte(dev, 0x7c, &temp);
+ pci_write_config_byte(dev, 0x7c, 0x80);
+
+ /* set as P2P bridge */
+ pci_write_config_byte(dev, PCI_CLASS_PROG, 0x01);
+ dev->class |= 0x1;
+
+ /* restore lock */
+ pci_write_config_byte(dev, 0x7c, temp);
+}
+
+
+static void __devinit quirk_uli1575(struct pci_dev *dev)
+{
+ int i;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ /*
+ * ULI1575 interrupts route setup
+ */
+
+ /* ULI1575 IRQ mapping conf register maps PIRQx to IRQn */
+ for (i = 0; i < 4; i++) {
+ u8 val = uli_pirq_to_irq[i*2] | (uli_pirq_to_irq[i*2+1] << 4);
+ pci_write_config_byte(dev, 0x48 + i, val);
+ }
+
+ /* USB 1.1 OHCI controller 1: dev 28, func 0 - IRQ12 */
+ pci_write_config_byte(dev, 0x86, ULI_PIRQD);
+
+ /* USB 1.1 OHCI controller 2: dev 28, func 1 - IRQ9 */
+ pci_write_config_byte(dev, 0x87, ULI_PIRQA);
+
+ /* USB 1.1 OHCI controller 3: dev 28, func 2 - IRQ10 */
+ pci_write_config_byte(dev, 0x88, ULI_PIRQB);
+
+ /* Lan controller: dev 27, func 0 - IRQ6 */
+ pci_write_config_byte(dev, 0x89, ULI_PIRQF);
+
+ /* AC97 Audio controller: dev 29, func 0 - IRQ6 */
+ pci_write_config_byte(dev, 0x8a, ULI_PIRQF);
+
+ /* Modem controller: dev 29, func 1 - IRQ6 */
+ pci_write_config_byte(dev, 0x8b, ULI_PIRQF);
+
+ /* HD Audio controller: dev 29, func 2 - IRQ6 */
+ pci_write_config_byte(dev, 0x8c, ULI_PIRQF);
+
+ /* SATA controller: dev 31, func 1 - IRQ5 */
+ pci_write_config_byte(dev, 0x8d, ULI_PIRQE);
+
+ /* SMB interrupt: dev 30, func 1 - IRQ7 */
+ pci_write_config_byte(dev, 0x8e, ULI_PIRQG);
+
+ /* PMU ACPI SCI interrupt: dev 30, func 2 - IRQ7 */
+ pci_write_config_byte(dev, 0x8f, ULI_PIRQG);
+
+ /* USB 2.0 controller: dev 28, func 3 */
+ pci_write_config_byte(dev, 0x74, ULI_8259_IRQ11);
+
+ /* Primary PATA IDE IRQ: 14
+ * Secondary PATA IDE IRQ: 15
+ */
+ pci_write_config_byte(dev, 0x44, 0x30 | ULI_8259_IRQ14);
+ pci_write_config_byte(dev, 0x75, ULI_8259_IRQ15);
+}
+
+static void __devinit quirk_final_uli1575(struct pci_dev *dev)
+{
+ /* Set i8259 interrupt trigger
+ * IRQ 3: Level
+ * IRQ 4: Level
+ * IRQ 5: Level
+ * IRQ 6: Level
+ * IRQ 7: Level
+ * IRQ 9: Level
+ * IRQ 10: Level
+ * IRQ 11: Level
+ * IRQ 12: Level
+ * IRQ 14: Edge
+ * IRQ 15: Edge
+ */
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ outb(0xfa, 0x4d0);
+ outb(0x1e, 0x4d1);
+
+ /* setup RTC */
+ CMOS_WRITE(RTC_SET, RTC_CONTROL);
+ CMOS_WRITE(RTC_24H, RTC_CONTROL);
+
+ /* ensure month, date, and week alarm fields are ignored */
+ CMOS_WRITE(0, RTC_VALID);
+
+ outb_p(0x7c, 0x72);
+ outb_p(RTC_ALARM_DONT_CARE, 0x73);
+
+ outb_p(0x7d, 0x72);
+ outb_p(RTC_ALARM_DONT_CARE, 0x73);
+}
+
+/* SATA */
+static void __devinit quirk_uli5288(struct pci_dev *dev)
+{
+ unsigned char c;
+ unsigned int d;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ /* read/write lock */
+ pci_read_config_byte(dev, 0x83, &c);
+ pci_write_config_byte(dev, 0x83, c|0x80);
+
+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &d);
+ d = (d & 0xff) | (PCI_CLASS_STORAGE_SATA_AHCI << 8);
+ pci_write_config_dword(dev, PCI_CLASS_REVISION, d);
+
+ /* restore lock */
+ pci_write_config_byte(dev, 0x83, c);
+
+ /* disable emulated PATA mode enabled */
+ pci_read_config_byte(dev, 0x84, &c);
+ pci_write_config_byte(dev, 0x84, c & ~0x01);
+}
+
+/* PATA */
+static void __devinit quirk_uli5229(struct pci_dev *dev)
+{
+ unsigned short temp;
+
+ if (!uses_fsl_uli_m1575)
+ return;
+
+ pci_write_config_word(dev, PCI_COMMAND, PCI_COMMAND_INTX_DISABLE |
+ PCI_COMMAND_MASTER | PCI_COMMAND_IO);
+
+ /* Enable Native IRQ 14/15 */
+ pci_read_config_word(dev, 0x4a, &temp);
+ pci_write_config_word(dev, 0x4a, temp | 0x1000);
+}
+
+/* We have to do a dummy read on the P2P for the RTC to work, WTF */
+static void __devinit quirk_final_uli5249(struct pci_dev *dev)
+{
+ int i;
+ u8 *dummy;
+ struct pci_bus *bus = dev->bus;
+
+ for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
+ if ((bus->resource[i]) &&
+ (bus->resource[i]->flags & IORESOURCE_MEM)) {
+ dummy = ioremap(bus->resource[i]->start, 0x4);
+ if (dummy) {
+ in_8(dummy);
+ iounmap(dummy);
+ }
+ break;
+ }
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, 0x5249, early_uli5249);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x1575, quirk_uli1575);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5288, quirk_uli5288);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, 0x5229, quirk_uli5229);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x5249, quirk_final_uli5249);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, 0x1575, quirk_final_uli1575);
+
+int uli_exclude_device(struct pci_controller *hose,
+ u_char bus, u_char devfn)
+{
+ if (bus == (hose->first_busno + 2)) {
+ /* exclude Modem controller */
+ if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 1))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ /* exclude HD Audio controller */
+ if ((PCI_SLOT(devfn) == 29) && (PCI_FUNC(devfn) == 2))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
--
1.5.2.2
^ permalink raw reply related
* [PATCH] serial: Add pci ids for PA Semi PWRficient onchip uarts
From: Olof Johansson @ 2007-08-17 4:09 UTC (permalink / raw)
To: akpm; +Cc: linuxppc-dev, linux-kernel, Alan Cox
Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Index: linux-2.6/drivers/serial/8250_pci.c
===================================================================
--- linux-2.6.orig/drivers/serial/8250_pci.c
+++ linux-2.6/drivers/serial/8250_pci.c
@@ -984,6 +984,7 @@ enum pci_board_num_t {
pbn_exar_XR17C152,
pbn_exar_XR17C154,
pbn_exar_XR17C158,
+ pbn_pasemi_1682M,
};
/*
@@ -1511,6 +1512,14 @@ static struct pciserial_board pci_boards
.base_baud = 921600,
.uart_offset = 0x200,
},
+ /*
+ * PA Semi PWRficient PA6T-1682M on-chip UART
+ */
+ [pbn_pasemi_1682M] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 8333333,
+ },
};
/*
@@ -2402,6 +2411,13 @@ static struct pci_device_id serial_pci_t
PCI_SUBVENDOR_ID_PERLE, PCI_SUBDEVICE_ID_PCI_RAS8,
0, 0, pbn_b2_8_921600 },
/*
+ * PA Semi PA6T-1682M on-chip UART
+ */
+ { PCI_VENDOR_ID_PASEMI, 0xa004,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_pasemi_1682M },
+
+ /*
* These entries match devices with class COMMUNICATION_SERIAL,
* COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
*/
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox