* [PATCH 2/2] powerpc/dts: Add dts for p1025rdb board
From: Zhicheng Fan @ 2012-01-18 9:01 UTC (permalink / raw)
To: linuxppc-dev, galak; +Cc: Fanzc
In-Reply-To: <1326877318-21352-1-git-send-email-B32736@freescale.com>
From: Fanzc <b32736@freeescale.com>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Fanzc <b32736@freeescale.com>
---
arch/powerpc/boot/dts/fsl/p1025si-post.dtsi | 228 +++++++++++++++++++++
arch/powerpc/boot/dts/fsl/p1025si-pre.dtsi | 70 +++++++
arch/powerpc/boot/dts/p1025rdb.dts | 113 +++++++++++
arch/powerpc/boot/dts/p1025rdb.dtsi | 286 +++++++++++++++++++++++++++
arch/powerpc/boot/dts/p1025rdb_36b.dts | 65 ++++++
5 files changed, 762 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/fsl/p1025si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/p1025si-pre.dtsi
create mode 100644 arch/powerpc/boot/dts/p1025rdb.dts
create mode 100644 arch/powerpc/boot/dts/p1025rdb.dtsi
create mode 100644 arch/powerpc/boot/dts/p1025rdb_36b.dts
diff --git a/arch/powerpc/boot/dts/fsl/p1025si-post.dtsi b/arch/powerpc/boot/dts/fsl/p1025si-post.dtsi
new file mode 100644
index 0000000..e0e3e4d
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1025si-post.dtsi
@@ -0,0 +1,228 @@
+/*
+ * P1025 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,p1025-elbc", "fsl,elbc", "simple-bus";
+ interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+ >;
+ };
+};
+
+/* controller at 0xa000 */
+&pci1 {
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 255>;
+ clock-frequency = <33333333>;
+ interrupts = <16 2 0 0>;
+
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <16 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+ 0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+ 0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+ 0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+ >;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,p1025-immr", "simple-bus";
+ bus-frequency = <0>; // Filled out by uboot.
+
+ ecm-law@0 {
+ compatible = "fsl,ecm-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <12>;
+ };
+
+ ecm@1000 {
+ compatible = "fsl,p1025-ecm", "fsl,ecm";
+ reg = <0x1000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+ memory-controller@2000 {
+ compatible = "fsl,p1025-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+ spi@7000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "pq3-gpio-0.dtsi"
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,p1025-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x40000>; // L2,256K
+ interrupts = <16 2 0 0>;
+ };
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+ sdhc@2e000 {
+ sdhci,auto-cmd12;
+ };
+/include/ "pq3-sec3.3-0.dtsi"
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+ enet0: enet0_grp2: ethernet@b0000 {
+ };
+
+/include/ "pq3-etsec2-1.dtsi"
+ enet1: enet1_grp2: ethernet@b1000 {
+ };
+
+/include/ "pq3-etsec2-2.dtsi"
+ enet2: enet2_grp2: ethernet@b2000 {
+ };
+
+ global-utilities@e0000 {
+ compatible = "fsl,p1025-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+};
+
+&qe {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe";
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: interrupt-controller@80 {
+ interrupt-controller;
+ compatible = "fsl,qe-ic";
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x80>;
+ interrupts = <63 2 0 0 60 2 0 0>; //high:47 low:44
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ mdio@2120 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2120 0x18>;
+ compatible = "fsl,ucc-mdio";
+ };
+
+ ucc@2400 {
+ cell-index = <5>;
+ reg = <0x2400 0x200>;
+ interrupts = <40>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x6000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x6000>;
+ };
+ };
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"
diff --git a/arch/powerpc/boot/dts/fsl/p1025si-pre.dtsi b/arch/powerpc/boot/dts/fsl/p1025si-pre.dtsi
new file mode 100644
index 0000000..ef5f6db
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/p1025si-pre.dtsi
@@ -0,0 +1,70 @@
+/*
+ * P1025 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+ compatible = "fsl,P1025";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ ethernet4 = &enet4;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,P1025@0 {
+ device_type = "cpu";
+ reg = <0x0>;
+ next-level-cache = <&L2>;
+ };
+
+ PowerPC,P1025@1 {
+ device_type = "cpu";
+ reg = <0x1>;
+ next-level-cache = <&L2>;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1025rdb.dts b/arch/powerpc/boot/dts/p1025rdb.dts
new file mode 100644
index 0000000..21b7f46
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb.dts
@@ -0,0 +1,113 @@
+/*
+ * P1025 RDB Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+/include/ "fsl/p1025si-pre.dtsi"
+/ {
+ model = "fsl,P1025RDB";
+ compatible = "fsl,P1025RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes */
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe: qe@ffe80000 {
+ ranges = <0x0 0x0 0xffe80000 0x40000>;
+ reg = <0 0xffe80000 0 0x480>;
+ brg-frequency = <0>;
+ bus-frequency = <0>;
+ status = "disabled"; /* no firmware loaded */
+
+ enet3: ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "clk12";
+ tx-clock-name = "clk9";
+ pio-handle = <&pio1>;
+ phy-handle = <&qe_phy0>;
+ phy-connection-type = "mii";
+ };
+
+ mdio@2120 {
+ qe_phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <4 1 0 0>;
+ reg = <0x6>;
+ device_type = "ethernet-phy";
+ };
+ qe_phy1: ethernet-phy@03 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1 0 0>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet4: ucc@2400 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ rx-clock-name = "none";
+ tx-clock-name = "clk13";
+ pio-handle = <&pio2>;
+ phy-handle = <&qe_phy1>;
+ phy-connection-type = "rmii";
+ };
+ };
+};
+
+/include/ "p1025rdb.dtsi"
+/include/ "fsl/p1025si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1025rdb.dtsi b/arch/powerpc/boot/dts/p1025rdb.dtsi
new file mode 100644
index 0000000..46d9e33
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb.dtsi
@@ -0,0 +1,286 @@
+/*
+ * P1025 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "DTB Image";
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "Linux Kernel Image";
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1025-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND Linux Kernel Image";
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND Compressed RFS Image";
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND Writable User area";
+ };
+ };
+
+};
+
+&soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image */
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ /* USB2 is shared with localbus, so it must be disabled
+ by default. We can't put 'status = "disabled";' here
+ since U-Boot doesn't clear the status property when
+ it enables USB2. OTOH, U-Boot does create a new node
+ when there isn't any. So, just comment it out.
+ usb@23000 {
+ phy_type = "ulpi";
+ };
+ */
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ mdio@26000 {
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ par_io@e0100 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xe0100 0x60>;
+ ranges = <0x0 0xe0100 0x60>;
+ device_type = "par_io";
+ num-ports = <3>;
+ pio1: ucc_pin@01 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
+ 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
+ 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
+ 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
+ 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
+ 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
+ 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
+ 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
+ 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
+ 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
+ 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
+ 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
+ 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
+ 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
+ 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
+ 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
+ };
+
+ pio2: ucc_pin@02 {
+ pio-map = <
+ /* port pin dir open_drain assignment has_irq */
+ 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
+ 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
+ 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
+ 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
+ 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
+ 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
+ 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
+ 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
+ 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
+ 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1025rdb_36b.dts b/arch/powerpc/boot/dts/p1025rdb_36b.dts
new file mode 100644
index 0000000..01148f7
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1025rdb_36b.dts
@@ -0,0 +1,65 @@
+/*
+ * P1025 RDB Device Tree Source (36-bit address map)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/p1025si-pre.dtsi"
+/ {
+ model = "fsl,P1025RDB";
+ compatible = "fsl,P1025RDB";
+
+ memory {
+ device_type = "memory";
+ };
+
+ board_lbc: lbc: localbus@fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000>;
+ };
+
+ board_soc: soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0xe 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xe0000000
+ 0x2000000 0x0 0xe0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1025rdb.dtsi"
+/include/ "fsl/p1025si-post.dtsi"
--
1.7.0.4
^ permalink raw reply related
* Re: [PATCH 2/2] Kbuild: Use dtc's -d (dependency) option
From: Michal Marek @ 2012-01-18 10:07 UTC (permalink / raw)
To: Stephen Warren
Cc: Jonas Bonn, Jon Loeliger, Russell King,
linux-c6x-dev@linux-c6x.org, Arnd Bergmann, Aurelien Jacquiot,
Devicetree Discuss, microblaze-uclinux@itee.uq.edu.au,
linux-kbuild@vger.kernel.org, Michal Simek, Rob Herring,
linux-kernel@vger.kernel.org, Paul Mackerras, Mark Salter,
linuxppc-dev@lists.ozlabs.org, linux@openrisc.net,
linux-arm-kernel@lists.infradead.org, David Gibson
In-Reply-To: <74CDBE0F657A3D45AFBB94109FB122FF17801D2255@HQMAIL01.nvidia.com>
On 17.1.2012 18:20, Stephen Warren wrote:
> Michal Marek wrote at Saturday, January 14, 2012 3:51 PM:
>> As the C6X port has been merged in this merge window, I can't easily
>> apply this patch to my kbuild branch and at the same time please Linus
>> by basing the pull request on a tagged release. So I'm going to drop the
>> arch/c6x part to keep the kbuild branch "pretty" and let either Mark or
>> Stephen send the patch to Linus directly, once he has merged the kbuild
>> branch. Would that work?
>
> I was assuming my patches were for 3.4 rather than 3.3, since it's pretty
> late for new features in 3.3. In that case, there wouldn't be an issue,
> right?
OK, that was a misunderstanding then. I applied it to the kbuild branch
for 3.3 and Linus pulled it in the meantime. It's not a terribly
intrusive change, after all.
Michal
^ permalink raw reply
* Re: Cannot wake-up from standby with MPC8313
From: Norbert van Bolhuis @ 2012-01-18 10:16 UTC (permalink / raw)
To: Scott Wood; +Cc: linuxppc-dev@ozlabs.org
In-Reply-To: <4F15F17C.20202@freescale.com>
On 01/17/12 23:09, Scott Wood wrote:
...
>>
>> If CPU is stuck in sleep, JTAG will send HRESET or SRESET (i'm nor sure
>> which one it is) and u-boot is needed to reconfigure CPU and DDR2 SDRAM
>> ctrl.
>
> Why is a reset needed in order to examine physical memory?
>
Because CPU is stuck in sleep and I use the CPU to dump the physical memory
(which contains the log entries made just before CPU got stuck).
>> SDRAM contents (for physical memory "unknown" to u-boot and linux) seems to
>> survive such a soft-reset.
>
> And all register and device state is as Linux left it?
>
Probably not, but at least the physical memory contents seems to survive
the soft-reset.
>>>> It looks like an interupt does occur, but do_IRQ seems to be stuck
>>>> in ppc_md.get_irq=ipic_get_irq where it reads SIVCR.
>>>
>>> Stuck as in the load never completes, or as in ipic_get_irq() gets
>>> called repeatedly? If the latter, what value is it reading out? Is the
>>> interrupt pending in SIPNR at this point?
>>>
>>
>>
>> I think I was wrong. I enabled tracing do_IRQ just a little bit too soon
>> (in suspend_enter). The interrupt I saw was probably one that occured
>> just before CPU entered sleep (mpc6xx_enter_standby).
>>
>> Right now I see no external interrupt happening, so that brings us back
>> where we were before: I'm not getting an interrupt regardless of
>> low-power state.
>> So now my main question is: how can JTAG and/or any other external signal
>> cause this ?
>
> I can't help you with the hardware side of it, other than to say that it
> sounds similar to an issue we had on early revs of mpc8313erdb. Could
> you make sure that TRST (JTAG Test Reset) is not being asserted except
> while PORESET is asserted?
>
> If that's not it, I'm wondering what the relevant difference is on the
> software side to differentiate the case where you go through all the
> motions but don't set MSR[POW] from the case where you don't try to
> suspend at all (just take the interrupt during normal execution). Are
> you sure that you're making it to mpc6xx_enter_standby, and that it's
> not hanging on a PMC register access?
>
>> Another weird thing I noticed is that whenever I dump CPU memmap
>> (which starts at 0xe0000000) under linux it always crashes with a "check
>> stop"
>> when it is displaying somewhere at 0xe0000800-0xe0001000
>> If I connect our JTAG debugger it never crashes and dumping CPU memmap
>> always works.
>
> Is it 0xe0000bXX? A hang when accessing the PMC registers is what I saw
> with the mpc8313erdb bug.
>
> -Scott
>
>
Yes this is it!
You mentioned mpc8313erdb bug before, I guess you had to mention it twice before
I looked at mpc8313erdb bug description.
The mpc8313erdb bug is described as follows:
3.5 Power management control (PMC) registers cannot be
accessed?
The PMC registers range from IMMR + 0x0B00 to IMMR + 0x0BFF. When this
area is accessed in u-boot,
the RDB hangs up. It appears that the PMC block is related to the JTAG
interface; TRST must not be pulled
down for normal operation of the PMC block. Possible workarounds are as
follows:
• Attach a debugger to drive TRST high during normal operation.
• Remove the pull-down resistor (R37) for TRST. Although this tested on
some RDBs without any
problem, it violates the hardware specification. If it does not work on
your RDB, use another workaround.
I guess this is an MPC8313 problem rather than an MPC8313E-RDB problem ?
and I would expect it to be mentioned in MPC8313E Errata (which isn't the
case).
Anyway, thanks a lot for all help!
---
NvBolhuis
^ permalink raw reply
* Re: Problem with full speed devices on PowerPC MPC5121 host port
From: Anatolij Gustschin @ 2012-01-18 11:08 UTC (permalink / raw)
To: Matthias Fuchs; +Cc: linuxppc-dev, linux-usb
In-Reply-To: <4F1581E2.9030400@esd.eu>
[-- Attachment #1: Type: text/plain, Size: 2149 bytes --]
Hi Matthias,
On Tue, 17 Jan 2012 15:12:50 +0100
Matthias Fuchs <matthias.fuchs@esd.eu> wrote:
> On 06.01.2012 19:03, Alan Stern wrote:
> > On Fri, 6 Jan 2012, Matthias Fuchs wrote:
> >
> >> For my eyes it does not really look like a general USB issue.
> >> It looks like a problem with the Freescale EHCI implementation that is
> >> influenced by high interrupt or internal bus load caused by the flood ping.
> >
> > Indeed, it might be a problem with the built-in Transaction Translator.
> > That would explain why it affect full-speed devices.
> >
> > However, I would expect the resetting the controller hardware (which
> > happens when you reload the ehci-fsl driver) would fix any such issues.
> > It's hard to imagine how a problem could survive a reset like that.
>
> I did the tests again. When the error occured I reloaded the ehci-hcd driver and reconnected the device. It ends up with some kernel messages
> that come up time after time:
>
> usb 1-1: new full-speed USB device number 2 using fsl-ehci
> usb 1-1: device descriptor read/64, error -110
> usb 1-1: device descriptor read/64, error -110
> usb 1-1: new full-speed USB device number 3 using fsl-ehci
> usb 1-1: device descriptor read/64, error -110
> usb 1-1: device descriptor read/64, error -110
> usb 1-1: new full-speed USB device number 4 using fsl-ehci
> usb 1-1: device not accepting address 4, error -110
> usb 1-1: new full-speed USB device number 5 using fsl-ehci
> usb 1-1: device not accepting address 5, error -110
> hub 1-0:1.0: unable to enumerate USB device on port 1
>
> A recommondation from freescale was to check the TXFILLTUNING register settings ("Initialization of this registers can produce problem if full-speed device is used").
>
> So I tried various values in the TXFILLTUNING register (I added this
> code to ehci_reset()). Finally I disabled USB streaming mode in the USBMODE register (set bit USBMODE_SDIS - btw., it should be defined as "1 << 4" in ehci_def.h at least for the MPC5121).
>
> All this does not fix the problem or even have an impact.
Can you try the attached patch? Does it have an impact?
Best regards,
Anatolij
[-- Attachment #2: 0001-usb-ehci-fsl-set-INCR8-mode-for-system-bus-interface.patch --]
[-- Type: text/x-patch, Size: 2242 bytes --]
>From 4cf7463af262230fcc0db95b2f47b0dcbf76daa9 Mon Sep 17 00:00:00 2001
From: Anatolij Gustschin <agust@denx.de>
Date: Wed, 18 Jan 2012 01:01:06 +0100
Subject: [PATCH] usb: ehci-fsl: set INCR8 mode for system bus interface
Port commit 69b4acc1dc4aa98a8f1016684fc99aba10156f87
(USB: Set INCR8 mode for system bus interface.) from Freescale
ltib 2.6.24 kernel for mpc512x:
This is a work-around for the USB-bus-hang problem observed
on MPC512x when there is heavy simultaneous PATA write activity.
See also "12.4 The USB controller can issue transactions that lock
up the AHB bus under certain conditions" in MPC5121e (M36P) Errata
Signed-off-by: Anatolij Gustschin <agust@denx.de>
---
drivers/usb/host/ehci-fsl.c | 10 ++++++++++
drivers/usb/host/ehci-fsl.h | 2 ++
2 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index e90344a..a6a6722 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -346,6 +346,14 @@ static int ehci_fsl_setup(struct usb_hcd *hcd)
ehci_reset(ehci);
+#ifdef CONFIG_PPC_MPC512x
+ /*
+ * set SBUSCFG:AHBBRST so that control msgs don't
+ * fail when doing heavy PATA writes.
+ */
+ ehci_writel(ehci, SBUSCFG_INCR8, hcd->regs + FSL_SOC_USB_SBUSCFG);
+#endif
+
retval = ehci_fsl_reinit(ehci);
return retval;
}
@@ -469,6 +477,8 @@ static int ehci_fsl_mpc512x_drv_resume(struct device *dev)
ehci_writel(ehci, ISIPHYCTRL_PXE | ISIPHYCTRL_PHYE,
hcd->regs + FSL_SOC_USB_ISIPHYCTRL);
+ ehci_writel(ehci, SBUSCFG_INCR8, hcd->regs + FSL_SOC_USB_SBUSCFG);
+
/* restore EHCI registers */
ehci_writel(ehci, pdata->pm_command, &ehci->regs->command);
ehci_writel(ehci, pdata->pm_intr_enable, &ehci->regs->intr_enable);
diff --git a/drivers/usb/host/ehci-fsl.h b/drivers/usb/host/ehci-fsl.h
index 4918062..0855be8 100644
--- a/drivers/usb/host/ehci-fsl.h
+++ b/drivers/usb/host/ehci-fsl.h
@@ -19,6 +19,8 @@
#define _EHCI_FSL_H
/* offsets for the non-ehci registers in the FSL SOC USB controller */
+#define FSL_SOC_USB_SBUSCFG 0x90
+#define SBUSCFG_INCR8 0x02 /* INCR8, specified */
#define FSL_SOC_USB_ULPIVP 0x170
#define FSL_SOC_USB_PORTSC1 0x184
#define PORT_PTS_MSK (3<<30)
--
1.7.1
^ permalink raw reply related
* Re: Problem with full speed devices on PowerPC MPC5121 host port
From: Matthias Fuchs @ 2012-01-18 13:42 UTC (permalink / raw)
To: Anatolij Gustschin; +Cc: linuxppc-dev, linux-usb
In-Reply-To: <20120118120811.04f7c601@wker>
Hi Anatolij,
On 18.01.2012 12:08, Anatolij Gustschin wrote:
> Hi Matthias,
>
> On Tue, 17 Jan 2012 15:12:50 +0100
> Matthias Fuchs <matthias.fuchs@esd.eu> wrote:
>
>> On 06.01.2012 19:03, Alan Stern wrote:
>>> On Fri, 6 Jan 2012, Matthias Fuchs wrote:
>>>
>>>> For my eyes it does not really look like a general USB issue.
>>>> It looks like a problem with the Freescale EHCI implementation that is
>>>> influenced by high interrupt or internal bus load caused by the flood ping.
>>>
>>> Indeed, it might be a problem with the built-in Transaction Translator.
>>> That would explain why it affect full-speed devices.
>>>
>>> However, I would expect the resetting the controller hardware (which
>>> happens when you reload the ehci-fsl driver) would fix any such issues.
>>> It's hard to imagine how a problem could survive a reset like that.
>>
>> I did the tests again. When the error occured I reloaded the ehci-hcd driver and reconnected the device. It ends up with some kernel messages
>> that come up time after time:
>>
>> usb 1-1: new full-speed USB device number 2 using fsl-ehci
>> usb 1-1: device descriptor read/64, error -110
>> usb 1-1: device descriptor read/64, error -110
>> usb 1-1: new full-speed USB device number 3 using fsl-ehci
>> usb 1-1: device descriptor read/64, error -110
>> usb 1-1: device descriptor read/64, error -110
>> usb 1-1: new full-speed USB device number 4 using fsl-ehci
>> usb 1-1: device not accepting address 4, error -110
>> usb 1-1: new full-speed USB device number 5 using fsl-ehci
>> usb 1-1: device not accepting address 5, error -110
>> hub 1-0:1.0: unable to enumerate USB device on port 1
>>
>> A recommondation from freescale was to check the TXFILLTUNING register settings ("Initialization of this registers can produce problem if full-speed device is used").
>>
>> So I tried various values in the TXFILLTUNING register (I added this
>> code to ehci_reset()). Finally I disabled USB streaming mode in the USBMODE register (set bit USBMODE_SDIS - btw., it should be defined as "1 << 4" in ehci_def.h at least for the MPC5121).
>>
>> All this does not fix the problem or even have an impact.
>
> Can you try the attached patch? Does it have an impact?
Yes, in deed, it solved my problem :-) Finally I noticed that
the problem is listed in the CPU's errata document.
You could update the comment and commit message to "... when there is
heavy simultaneus PATA write or network activity".
I vote for getting this mainline.
Tested-by: Matthias Fuchs <matthias.fuchs@esd.ue>
Matthias
^ permalink raw reply
* Re: [PATCH] powerpc/85xx:Add dr_mode property in USB nodes
From: Kumar Gala @ 2012-01-18 14:26 UTC (permalink / raw)
To: Ramneek Mehresh; +Cc: devicetree-discuss, linuxppc-dev
In-Reply-To: <1326869326-4271-1-git-send-email-ramneek.mehresh@freescale.com>
On Jan 18, 2012, at 12:48 AM, Ramneek Mehresh wrote:
> Add usb2 controller node for P1020RDB, P2020RDB, P2020DS, P1021MDS
>
> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
> ---
> Applies on git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git
> (branch next)
>
> arch/powerpc/boot/dts/p1020rdb.dtsi | 2 ++
> arch/powerpc/boot/dts/p1021mds.dts | 3 ++-
> arch/powerpc/boot/dts/p2020ds.dtsi | 3 ++-
> arch/powerpc/boot/dts/p2020rdb.dts | 3 ++-
> 4 files changed, 8 insertions(+), 3 deletions(-)
applied to merge
- k
^ permalink raw reply
* Re: [PATCH] powerpc/85xx:Enable USB2 controller node for P1020RDB
From: Kumar Gala @ 2012-01-18 14:26 UTC (permalink / raw)
To: Ramneek Mehresh; +Cc: devicetree-discuss, linuxppc-dev
In-Reply-To: <1326865839-3612-1-git-send-email-ramneek.mehresh@freescale.com>
On Jan 17, 2012, at 11:50 PM, Ramneek Mehresh wrote:
> Enable USB2 controller node for P1020RDB. USB2 controller is used only
> when board boots from SPI or SD as it is muxed with eLBC
>
> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
> ---
> Applies on git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git
> (branch next)
>
> arch/powerpc/boot/dts/p1020rdb.dtsi | 11 ++++-------
> 1 files changed, 4 insertions(+), 7 deletions(-)
applied to merge
- k
^ permalink raw reply
* Re: [git pull] Please pull powerpc.git merge branch (updated)
From: Kumar Gala @ 2012-01-18 14:25 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev
In-Reply-To: <alpine.LFD.2.00.1201171625100.8416@right.am.freescale.net>
Ben,
Dropped the P1020RDB device tree patch as it was for the wrong board
revision and pulled in some additional usb device tree fixes.
- k
The following changes since commit c2bc3a316a7281f67e36b34dac2802cbe36a9128:
Merge branch 'x86/rdrand' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip (2012-01-16 18:23:09 -0800)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc.git merge
Jerry Huang (1):
powerpc/85xx: Fix cmd12 bug and add the chip compatible for eSDHC
Julia Lawall (1):
arch/powerpc/sysdev/fsl_pci.c: add missing iounmap
Michael Neuling (1):
powerpc: fix compile error with 85xx/p1022_ds.c
Ramneek Mehresh (2):
powerpc/85xx: Enable USB2 controller node for P1020RDB
powerpc/85xx: Add dr_mode property in USB nodes
arch/powerpc/boot/dts/fsl/mpc8536si-post.dtsi | 4 ++++
arch/powerpc/boot/dts/fsl/p1010si-post.dtsi | 3 ++-
arch/powerpc/boot/dts/fsl/p1020si-post.dtsi | 4 ++++
arch/powerpc/boot/dts/fsl/p1022si-post.dtsi | 3 ++-
arch/powerpc/boot/dts/fsl/p2020si-post.dtsi | 4 ++++
arch/powerpc/boot/dts/p1020rdb.dtsi | 13 ++++++-------
arch/powerpc/boot/dts/p1021mds.dts | 3 ++-
arch/powerpc/boot/dts/p2020ds.dtsi | 3 ++-
arch/powerpc/boot/dts/p2020rdb.dts | 3 ++-
arch/powerpc/platforms/85xx/p1022_ds.c | 1 +
arch/powerpc/sysdev/fsl_pci.c | 5 +++--
11 files changed, 32 insertions(+), 14 deletions(-)
^ permalink raw reply
* [PATCH] powerpc/booke64: Configurable lazy interrupt disabling
From: Laurentiu Tudor @ 2012-01-18 14:35 UTC (permalink / raw)
To: linuxppc-dev; +Cc: Laurentiu Tudor
This patch adds a menuconfig option that allows controlling
the lazy interrupt disabling feature implemented by this
commit:
commit d04c56f73c30a5e593202ecfcf25ed43d42363a2
Author: Paul Mackerras
Date: Wed Oct 4 16:47:49 2006 +1000
[POWERPC] Lazy interrupt disabling for 64-bit machines
The code in 'powerpc/include/asm/hw_irq.h' was rearranged and
cleaned-up a bit in order to reduce the number of needed #ifdef's.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
---
Patch is against
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git next
arch/powerpc/Kconfig | 16 ++++++
arch/powerpc/include/asm/hw_irq.h | 86 ++++++++++++++--------------------
arch/powerpc/include/asm/irqflags.h | 22 +++++++++
arch/powerpc/include/asm/paca.h | 4 ++
arch/powerpc/kernel/asm-offsets.c | 3 +
arch/powerpc/kernel/entry_64.S | 4 ++
arch/powerpc/kernel/exceptions-64e.S | 36 +++++++++++---
arch/powerpc/kernel/head_64.S | 10 ++++
arch/powerpc/kernel/idle_book3e.S | 7 +++
arch/powerpc/kernel/irq.c | 5 ++
arch/powerpc/kernel/setup_64.c | 2 +
11 files changed, 138 insertions(+), 57 deletions(-)
diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
index ce5e045..2792278 100644
--- a/arch/powerpc/Kconfig
+++ b/arch/powerpc/Kconfig
@@ -609,6 +609,22 @@ config SECCOMP
If unsure, say Y. Only embedded should say N here.
+config PPC_LAZY_EE
+ bool
+ prompt "Lazy interrupt disabling" if PPC_BOOK3E_64
+ default y if PPC_BOOK3S_64
+ help
+ Local interrupt disabling functions don't disable
+ interrupts right away and instead just clear an
+ internal 'interrupts are enabled' flag. If an
+ interrupt is triggered during this time, the
+ interrupt handling code checks the flag, and if
+ interrupts are supposed to be off, disables them
+ for real and returns, skipping interrupt handling.
+ When interrupts are enabled back, the interrupt
+ fires again and this time gets handled.
+
+ If unsure, say N.
endmenu
config ISA_DMA_API
diff --git a/arch/powerpc/include/asm/hw_irq.h b/arch/powerpc/include/asm/hw_irq.h
index bb712c9..6f32593 100644
--- a/arch/powerpc/include/asm/hw_irq.h
+++ b/arch/powerpc/include/asm/hw_irq.h
@@ -13,7 +13,20 @@
extern void timer_interrupt(struct pt_regs *);
+#ifdef CONFIG_BOOKE
+#define __hard_irq_enable() asm volatile("wrteei 1" : : : "memory");
+#define __hard_irq_disable() asm volatile("wrteei 0" : : : "memory");
+#else
#ifdef CONFIG_PPC64
+#define __hard_irq_enable() __mtmsrd(mfmsr() | MSR_EE, 1)
+#define __hard_irq_disable() __mtmsrd(mfmsr() & ~MSR_EE, 1)
+#else
+#define __hard_irq_enable() mtmsr(mfmsr() | MSR_EE)
+#define __hard_irq_disable() mtmsr(mfmsr() & ~MSR_EE)
+#endif
+#endif /* CONFIG_BOOKE */
+
+#if defined(CONFIG_PPC64) && defined(CONFIG_PPC_LAZY_EE)
#include <asm/paca.h>
static inline unsigned long arch_local_save_flags(void)
@@ -49,9 +62,11 @@ static inline void arch_local_irq_enable(void)
arch_local_irq_restore(1);
}
-static inline unsigned long arch_local_irq_save(void)
+static inline void hard_irq_disable(void)
{
- return arch_local_irq_disable();
+ __hard_irq_disable();
+ get_paca()->soft_enabled = 0;
+ get_paca()->hard_enabled = 0;
}
static inline bool arch_irqs_disabled_flags(unsigned long flags)
@@ -59,29 +74,7 @@ static inline bool arch_irqs_disabled_flags(unsigned long flags)
return flags == 0;
}
-static inline bool arch_irqs_disabled(void)
-{
- return arch_irqs_disabled_flags(arch_local_save_flags());
-}
-
-#ifdef CONFIG_PPC_BOOK3E
-#define __hard_irq_enable() asm volatile("wrteei 1" : : : "memory");
-#define __hard_irq_disable() asm volatile("wrteei 0" : : : "memory");
-#else
-#define __hard_irq_enable() __mtmsrd(mfmsr() | MSR_EE, 1)
-#define __hard_irq_disable() __mtmsrd(mfmsr() & ~MSR_EE, 1)
-#endif
-
-#define hard_irq_disable() \
- do { \
- __hard_irq_disable(); \
- get_paca()->soft_enabled = 0; \
- get_paca()->hard_enabled = 0; \
- } while(0)
-
-#else /* CONFIG_PPC64 */
-
-#define SET_MSR_EE(x) mtmsr(x)
+#else /* CONFIG_PPC64 && CONFIG_PPC_LAZY_EE */
static inline unsigned long arch_local_save_flags(void)
{
@@ -97,34 +90,24 @@ static inline void arch_local_irq_restore(unsigned long flags)
#endif
}
-static inline unsigned long arch_local_irq_save(void)
+static inline void arch_local_irq_enable(void)
{
- unsigned long flags = arch_local_save_flags();
-#ifdef CONFIG_BOOKE
- asm volatile("wrteei 0" : : : "memory");
-#else
- SET_MSR_EE(flags & ~MSR_EE);
-#endif
- return flags;
+ __hard_irq_enable();
}
-static inline void arch_local_irq_disable(void)
+static inline unsigned long arch_local_irq_disable(void)
{
-#ifdef CONFIG_BOOKE
- asm volatile("wrteei 0" : : : "memory");
-#else
- arch_local_irq_save();
-#endif
+ unsigned long flags;
+
+ flags = arch_local_save_flags();
+ __hard_irq_disable();
+
+ return flags;
}
-static inline void arch_local_irq_enable(void)
+static inline void hard_irq_disable(void)
{
-#ifdef CONFIG_BOOKE
- asm volatile("wrteei 1" : : : "memory");
-#else
- unsigned long msr = mfmsr();
- SET_MSR_EE(msr | MSR_EE);
-#endif
+ __hard_irq_disable();
}
static inline bool arch_irqs_disabled_flags(unsigned long flags)
@@ -132,15 +115,18 @@ static inline bool arch_irqs_disabled_flags(unsigned long flags)
return (flags & MSR_EE) == 0;
}
+#endif /* CONFIG_PPC64 && CONFIG_PPC_LAZY_EE */
+
+static inline unsigned long arch_local_irq_save(void)
+{
+ return arch_local_irq_disable();
+}
+
static inline bool arch_irqs_disabled(void)
{
return arch_irqs_disabled_flags(arch_local_save_flags());
}
-#define hard_irq_disable() arch_local_irq_disable()
-
-#endif /* CONFIG_PPC64 */
-
#define ARCH_IRQ_INIT_FLAGS IRQ_NOREQUEST
/*
diff --git a/arch/powerpc/include/asm/irqflags.h b/arch/powerpc/include/asm/irqflags.h
index b0b06d8..9685b75c 100644
--- a/arch/powerpc/include/asm/irqflags.h
+++ b/arch/powerpc/include/asm/irqflags.h
@@ -39,6 +39,8 @@
#define TRACE_ENABLE_INTS TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_on)
#define TRACE_DISABLE_INTS TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_off)
+#ifdef CONFIG_PPC_LAZY_EE
+
#define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip) \
cmpdi en,0; \
bne 95f; \
@@ -51,12 +53,32 @@
TRACE_AND_RESTORE_IRQ_PARTIAL(en,96f); \
stb en,PACASOFTIRQEN(r13); \
96:
+
+#else /* CONFIG_PPC_LAZY_EE */
+
+#define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip) \
+ cmpdi en,0; \
+ bne 95f; \
+ TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_off) \
+ b skip; \
+95: TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_on) \
+ li en,1;
+#define TRACE_AND_RESTORE_IRQ(en) \
+ TRACE_AND_RESTORE_IRQ_PARTIAL(en,96f); \
+96:
+
+#endif /* CONFIG_PPC_LAZY_EE */
+
#else
#define TRACE_ENABLE_INTS
#define TRACE_DISABLE_INTS
#define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip)
+#ifdef CONFIG_PPC_LAZY_EE
#define TRACE_AND_RESTORE_IRQ(en) \
stb en,PACASOFTIRQEN(r13)
+#else
+#define TRACE_AND_RESTORE_IRQ(en)
+#endif
#endif
#endif
diff --git a/arch/powerpc/include/asm/paca.h b/arch/powerpc/include/asm/paca.h
index 269c05a..b74c2b1 100644
--- a/arch/powerpc/include/asm/paca.h
+++ b/arch/powerpc/include/asm/paca.h
@@ -131,8 +131,12 @@ struct paca_struct {
u64 saved_r1; /* r1 save for RTAS calls or PM */
u64 saved_msr; /* MSR saved here by enter_rtas */
u16 trap_save; /* Used when bad stack is encountered */
+
+#ifdef CONFIG_PPC_LAZY_EE
u8 soft_enabled; /* irq soft-enable flag */
u8 hard_enabled; /* set if irqs are enabled in MSR */
+#endif
+
u8 io_sync; /* writel() needs spin_unlock sync */
u8 irq_work_pending; /* IRQ_WORK interrupt while soft-disable */
u8 nap_state_lost; /* NV GPR values lost in power7_idle */
diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c
index 04caee7..5b1fac9 100644
--- a/arch/powerpc/kernel/asm-offsets.c
+++ b/arch/powerpc/kernel/asm-offsets.c
@@ -146,8 +146,11 @@ int main(void)
DEFINE(PACATOC, offsetof(struct paca_struct, kernel_toc));
DEFINE(PACAKBASE, offsetof(struct paca_struct, kernelbase));
DEFINE(PACAKMSR, offsetof(struct paca_struct, kernel_msr));
+#ifdef CONFIG_PPC_LAZY_EE
DEFINE(PACASOFTIRQEN, offsetof(struct paca_struct, soft_enabled));
DEFINE(PACAHARDIRQEN, offsetof(struct paca_struct, hard_enabled));
+#endif
+
DEFINE(PACACONTEXTID, offsetof(struct paca_struct, context.id));
#ifdef CONFIG_PPC_MM_SLICES
DEFINE(PACALOWSLICESPSIZE, offsetof(struct paca_struct,
diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S
index d834425..ce7620b 100644
--- a/arch/powerpc/kernel/entry_64.S
+++ b/arch/powerpc/kernel/entry_64.S
@@ -124,8 +124,10 @@ END_FW_FTR_SECTION_IFSET(FW_FEATURE_SPLPAR)
ld r12,_MSR(r1)
#endif /* CONFIG_TRACE_IRQFLAGS */
li r10,1
+#ifdef CONFIG_PPC_LAZY_EE
stb r10,PACASOFTIRQEN(r13)
stb r10,PACAHARDIRQEN(r13)
+#endif
std r10,SOFTE(r1)
#ifdef CONFIG_PPC_ISERIES
BEGIN_FW_FTR_SECTION
@@ -602,10 +604,12 @@ ALT_FW_FTR_SECTION_END_IFCLR(FW_FEATURE_ISERIES)
2:
TRACE_AND_RESTORE_IRQ(r5);
+#ifdef CONFIG_PPC_LAZY_EE
/* extract EE bit and use it to restore paca->hard_enabled */
ld r3,_MSR(r1)
rldicl r4,r3,49,63 /* r0 = (r3 >> 15) & 1 */
stb r4,PACAHARDIRQEN(r13)
+#endif
#ifdef CONFIG_PPC_BOOK3E
b .exception_return_book3e
diff --git a/arch/powerpc/kernel/exceptions-64e.S b/arch/powerpc/kernel/exceptions-64e.S
index 429983c..d17abb3 100644
--- a/arch/powerpc/kernel/exceptions-64e.S
+++ b/arch/powerpc/kernel/exceptions-64e.S
@@ -96,11 +96,6 @@
#define PROLOG_ADDITION_NONE_DBG
#define PROLOG_ADDITION_NONE_MC
-#define PROLOG_ADDITION_MASKABLE_GEN \
- lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
- cmpwi cr0,r11,0; /* yes -> go out of line */ \
- beq masked_interrupt_book3e;
-
#define PROLOG_ADDITION_2REGS_GEN \
std r14,PACA_EXGEN+EX_R14(r13); \
std r15,PACA_EXGEN+EX_R15(r13)
@@ -120,11 +115,29 @@
std r14,PACA_EXMC+EX_R14(r13); \
std r15,PACA_EXMC+EX_R15(r13)
+#ifdef CONFIG_PPC_LAZY_EE
+#define PROLOG_ADDITION_MASKABLE_GEN \
+ lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
+ cmpwi cr0,r11,0; /* yes -> go out of line */ \
+ beq masked_interrupt_book3e;
+
#define PROLOG_ADDITION_DOORBELL_GEN \
lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
cmpwi cr0,r11,0; /* yes -> go out of line */ \
beq masked_doorbell_book3e
-
+#else /* CONFIG_PPC_LAZY_EE */
+#define PROLOG_ADDITION_MASKABLE_GEN
+#define PROLOG_ADDITION_DOORBELL_GEN
+#endif /* CONFIG_PPC_LAZY_EE */
+
+#ifdef CONFIG_PPC_LAZY_EE
+#define GET_IRQ_SOFT_ENABLED \
+ lbz r11,PACASOFTIRQEN(r13)
+#else
+#define GET_IRQ_SOFT_ENABLED \
+ mfmsr r11; \
+ rlwimi r11,r11,0,16,16
+#endif
/* Core exception code for all exceptions except TLB misses.
* XXX: Needs to make SPRN_SPRG_GEN depend on exception type
@@ -148,7 +161,7 @@
mfspr r8,SPRN_XER; /* save XER in stackframe */ \
ld r9,excf+EX_R1(r13); /* load orig r1 back from PACA */ \
lwz r10,excf+EX_CR(r13); /* load orig CR back from PACA */ \
- lbz r11,PACASOFTIRQEN(r13); /* get current IRQ softe */ \
+ GET_IRQ_SOFT_ENABLED; /* get current IRQ softe */ \
ld r12,exception_marker@toc(r2); \
li r0,0; \
std r3,GPR10(r1); /* save r10 to stackframe */ \
@@ -169,11 +182,18 @@
/* Variants for the "ints" argument */
#define INTS_KEEP
+
+#ifdef CONFIG_PPC_LAZY_EE
#define INTS_DISABLE_SOFT \
stb r0,PACASOFTIRQEN(r13); /* mark interrupts soft-disabled */ \
TRACE_DISABLE_INTS;
#define INTS_DISABLE_HARD \
stb r0,PACAHARDIRQEN(r13); /* and hard disabled */
+#else
+#define INTS_DISABLE_SOFT
+#define INTS_DISABLE_HARD
+#endif
+
#define INTS_DISABLE_ALL \
INTS_DISABLE_SOFT \
INTS_DISABLE_HARD
@@ -553,6 +573,7 @@ kernel_dbg_exc:
MASKABLE_EXCEPTION(0x320, ehpriv, .unknown_exception, ACK_NONE)
+#ifdef CONFIG_PPC_LAZY_EE
/*
* An interrupt came in while soft-disabled; clear EE in SRR1,
* clear paca->hard_enabled and return.
@@ -577,6 +598,7 @@ masked_interrupt_book3e_common:
mfspr r13,SPRN_SPRG_GEN_SCRATCH;
rfi
b .
+#endif /* CONFIG_PPC_LAZY_EE */
/*
* This is called from 0x300 and 0x400 handlers after the prologs with
diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S
index 06c7251..017d669 100644
--- a/arch/powerpc/kernel/head_64.S
+++ b/arch/powerpc/kernel/head_64.S
@@ -559,12 +559,14 @@ _GLOBAL(pmac_secondary_start)
add r13,r13,r4 /* for this processor. */
SET_PACA(r13) /* Save vaddr of paca in an SPRG*/
+#ifdef CONFIG_PPC_LAZY_EE
/* Mark interrupts soft and hard disabled (they might be enabled
* in the PACA when doing hotplug)
*/
li r0,0
stb r0,PACASOFTIRQEN(r13)
stb r0,PACAHARDIRQEN(r13)
+#endif
/* Create a temp kernel stack for use before relocation is on. */
ld r1,PACAEMERGSP(r13)
@@ -621,14 +623,18 @@ __secondary_start:
#ifdef CONFIG_PPC_ISERIES
BEGIN_FW_FTR_SECTION
ori r4,r4,MSR_EE
+#ifdef CONFIG_PPC_LAZY_EE
li r8,1
stb r8,PACAHARDIRQEN(r13)
+#endif
END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif
+#ifdef CONFIG_PPC_LAZY_EE
BEGIN_FW_FTR_SECTION
stb r7,PACAHARDIRQEN(r13)
END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES)
stb r7,PACASOFTIRQEN(r13)
+#endif
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
@@ -775,8 +781,10 @@ _INIT_GLOBAL(start_here_common)
/* Load up the kernel context */
5:
+#ifdef CONFIG_PPC_LAZY_EE
li r5,0
stb r5,PACASOFTIRQEN(r13) /* Soft Disabled */
+#endif
#ifdef CONFIG_PPC_ISERIES
BEGIN_FW_FTR_SECTION
mfmsr r5
@@ -785,7 +793,9 @@ BEGIN_FW_FTR_SECTION
li r5,1
END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
#endif
+#ifdef CONFIG_PPC_LAZY_EE
stb r5,PACAHARDIRQEN(r13) /* Hard Disabled on others */
+#endif
bl .start_kernel
diff --git a/arch/powerpc/kernel/idle_book3e.S b/arch/powerpc/kernel/idle_book3e.S
index 16c002d..34b09e0 100644
--- a/arch/powerpc/kernel/idle_book3e.S
+++ b/arch/powerpc/kernel/idle_book3e.S
@@ -28,6 +28,7 @@ _GLOBAL(book3e_idle)
/* Hard disable interrupts */
wrteei 0
+#ifdef CONFIG_PPC_LAZY_EE
/* Now check if an interrupt came in while we were soft disabled
* since we may otherwise lose it (doorbells etc...). We know
* that since PACAHARDIRQEN will have been cleared in that case.
@@ -35,6 +36,7 @@ _GLOBAL(book3e_idle)
lbz r3,PACAHARDIRQEN(r13)
cmpwi cr0,r3,0
beqlr
+#endif
/* Now we are going to mark ourselves as soft and hard enables in
* order to be able to take interrupts while asleep. We inform lockdep
@@ -44,9 +46,12 @@ _GLOBAL(book3e_idle)
stdu r1,-128(r1)
bl .trace_hardirqs_on
#endif
+
+#ifdef CONFIG_PPC_LAZY_EE
li r0,1
stb r0,PACASOFTIRQEN(r13)
stb r0,PACAHARDIRQEN(r13)
+#endif
/* Interrupts will make use return to LR, so get something we want
* in there
@@ -56,10 +61,12 @@ _GLOBAL(book3e_idle)
/* Hard disable interrupts again */
wrteei 0
+#ifdef CONFIG_PPC_LAZY_EE
/* Mark them off again in the PACA as well */
li r0,0
stb r0,PACASOFTIRQEN(r13)
stb r0,PACAHARDIRQEN(r13)
+#endif
/* Tell lockdep about it */
#ifdef CONFIG_TRACE_IRQFLAGS
diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c
index 701d4ac..e2d1784 100644
--- a/arch/powerpc/kernel/irq.c
+++ b/arch/powerpc/kernel/irq.c
@@ -99,6 +99,8 @@ EXPORT_SYMBOL(irq_desc);
int distribute_irqs = 1;
+#ifdef CONFIG_PPC_LAZY_EE
+
static inline notrace unsigned long get_hard_enabled(void)
{
unsigned long enabled;
@@ -193,6 +195,9 @@ notrace void arch_local_irq_restore(unsigned long en)
__hard_irq_enable();
}
EXPORT_SYMBOL(arch_local_irq_restore);
+
+#endif /* CONFIG_PPC_LAZY_EE */
+
#endif /* CONFIG_PPC64 */
int arch_show_interrupts(struct seq_file *p, int prec)
diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c
index 4cb8f1e..06f5b19 100644
--- a/arch/powerpc/kernel/setup_64.c
+++ b/arch/powerpc/kernel/setup_64.c
@@ -233,8 +233,10 @@ void __init early_setup(unsigned long dt_ptr)
#ifdef CONFIG_SMP
void early_setup_secondary(void)
{
+#ifdef CONFIG_PPC_LAZY_EE
/* Mark interrupts enabled in PACA */
get_paca()->soft_enabled = 0;
+#endif
/* Initialize the hash table or TLB handling */
early_init_mmu_secondary();
--
1.7.5.1
^ permalink raw reply related
* [PATCH 1/2] powerpc/fsl-booke: Fixup calc_cam_sz to support MMU v2
From: Kumar Gala @ 2012-01-18 19:39 UTC (permalink / raw)
To: linuxppc-dev
The registers that describe size supported by TLB are different on MMU
v2 as well as we support power of two page sizes. For now we continue
to assume that FSL variable size array supports all page sizes up to the
maximum one reported in TLB1PS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/include/asm/reg_booke.h | 1 +
arch/powerpc/mm/fsl_booke_mmu.c | 19 +++++++++++++------
2 files changed, 14 insertions(+), 6 deletions(-)
diff --git a/arch/powerpc/include/asm/reg_booke.h b/arch/powerpc/include/asm/reg_booke.h
index 500fe1d..8a97aa7 100644
--- a/arch/powerpc/include/asm/reg_booke.h
+++ b/arch/powerpc/include/asm/reg_booke.h
@@ -62,6 +62,7 @@
#define SPRN_DVC2 0x13F /* Data Value Compare Register 2 */
#define SPRN_MAS8 0x155 /* MMU Assist Register 8 */
#define SPRN_TLB0PS 0x158 /* TLB 0 Page Size Register */
+#define SPRN_TLB1PS 0x159 /* TLB 1 Page Size Register */
#define SPRN_MAS5_MAS6 0x15c /* MMU Assist Register 5 || 6 */
#define SPRN_MAS8_MAS1 0x15d /* MMU Assist Register 8 || 1 */
#define SPRN_EPTCFG 0x15e /* Embedded Page Table Config */
diff --git a/arch/powerpc/mm/fsl_booke_mmu.c b/arch/powerpc/mm/fsl_booke_mmu.c
index 66a6fd3..07ba45b 100644
--- a/arch/powerpc/mm/fsl_booke_mmu.c
+++ b/arch/powerpc/mm/fsl_booke_mmu.c
@@ -149,12 +149,19 @@ static void settlbcam(int index, unsigned long virt, phys_addr_t phys,
unsigned long calc_cam_sz(unsigned long ram, unsigned long virt,
phys_addr_t phys)
{
- unsigned int camsize = __ilog2(ram) & ~1U;
- unsigned int align = __ffs(virt | phys) & ~1U;
- unsigned long max_cam = (mfspr(SPRN_TLB1CFG) >> 16) & 0xf;
-
- /* Convert (4^max) kB to (2^max) bytes */
- max_cam = max_cam * 2 + 10;
+ unsigned int camsize = __ilog2(ram);
+ unsigned int align = __ffs(virt | phys);
+ unsigned long max_cam;
+
+ if ((mfspr(SPRN_MMUCFG) & MMUCFG_MAVN) == MMUCFG_MAVN_V1) {
+ /* Convert (4^max) kB to (2^max) bytes */
+ max_cam = ((mfspr(SPRN_TLB1CFG) >> 16) & 0xf) * 2 + 10;
+ camsize &= ~1U;
+ align &= ~1U;
+ } else {
+ /* Convert (2^max) kB to (2^max) bytes */
+ max_cam = __ilog2(mfspr(SPRN_TLB1PS)) + 10;
+ }
if (camsize > align)
camsize = align;
--
1.7.3.4
^ permalink raw reply related
* [PATCH 2/2] powerpc: Add initial e6500 cpu support
From: Kumar Gala @ 2012-01-18 19:39 UTC (permalink / raw)
To: linuxppc-dev
In-Reply-To: <1326915580-19652-1-git-send-email-galak@kernel.crashing.org>
Add basic support for e6500 core in its single threaded mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
arch/powerpc/include/asm/cputable.h | 12 ++++++++----
arch/powerpc/kernel/cputable.c | 18 ++++++++++++++++++
2 files changed, 26 insertions(+), 4 deletions(-)
diff --git a/arch/powerpc/include/asm/cputable.h b/arch/powerpc/include/asm/cputable.h
index ad55a1c..b9219e9 100644
--- a/arch/powerpc/include/asm/cputable.h
+++ b/arch/powerpc/include/asm/cputable.h
@@ -390,6 +390,10 @@ extern const char *powerpc_base_platform;
CPU_FTR_L2CSR | CPU_FTR_LWSYNC | CPU_FTR_NOEXECUTE | \
CPU_FTR_DBELL | CPU_FTR_POPCNTB | CPU_FTR_POPCNTD | \
CPU_FTR_DEBUG_LVL_EXC)
+#define CPU_FTRS_E6500 (CPU_FTR_USE_TB | CPU_FTR_NODSISRALIGN | \
+ CPU_FTR_L2CSR | CPU_FTR_LWSYNC | CPU_FTR_NOEXECUTE | \
+ CPU_FTR_DBELL | CPU_FTR_POPCNTB | CPU_FTR_POPCNTD | \
+ CPU_FTR_DEBUG_LVL_EXC)
#define CPU_FTRS_GENERIC_32 (CPU_FTR_COMMON | CPU_FTR_NODSISRALIGN)
/* 64-bit CPUs */
@@ -442,7 +446,7 @@ extern const char *powerpc_base_platform;
#ifdef __powerpc64__
#ifdef CONFIG_PPC_BOOK3E
-#define CPU_FTRS_POSSIBLE (CPU_FTRS_E5500 | CPU_FTRS_A2)
+#define CPU_FTRS_POSSIBLE (CPU_FTRS_E6500 | CPU_FTRS_E5500 | CPU_FTRS_A2)
#else
#define CPU_FTRS_POSSIBLE \
(CPU_FTRS_POWER3 | CPU_FTRS_RS64 | CPU_FTRS_POWER4 | \
@@ -483,7 +487,7 @@ enum {
#endif
#ifdef CONFIG_E500
CPU_FTRS_E500 | CPU_FTRS_E500_2 | CPU_FTRS_E500MC |
- CPU_FTRS_E5500 |
+ CPU_FTRS_E5500 | CPU_FTRS_E6500 |
#endif
0,
};
@@ -491,7 +495,7 @@ enum {
#ifdef __powerpc64__
#ifdef CONFIG_PPC_BOOK3E
-#define CPU_FTRS_ALWAYS (CPU_FTRS_E5500 & CPU_FTRS_A2)
+#define CPU_FTRS_ALWAYS (CPU_FTRS_E6500 & CPU_FTRS_E5500 & CPU_FTRS_A2)
#else
#define CPU_FTRS_ALWAYS \
(CPU_FTRS_POWER3 & CPU_FTRS_RS64 & CPU_FTRS_POWER4 & \
@@ -528,7 +532,7 @@ enum {
#endif
#ifdef CONFIG_E500
CPU_FTRS_E500 & CPU_FTRS_E500_2 & CPU_FTRS_E500MC &
- CPU_FTRS_E5500 &
+ CPU_FTRS_E5500 & CPU_FTRS_E6500 &
#endif
CPU_FTRS_POSSIBLE,
};
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index 81db9e2..4dccf51 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -2019,6 +2019,24 @@ static struct cpu_spec __initdata cpu_specs[] = {
.machine_check = machine_check_e500mc,
.platform = "ppce5500",
},
+ { /* e6500 */
+ .pvr_mask = 0xffff0000,
+ .pvr_value = 0x80400000,
+ .cpu_name = "e6500",
+ .cpu_features = CPU_FTRS_E6500,
+ .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+ .mmu_features = MMU_FTR_TYPE_FSL_E | MMU_FTR_BIG_PHYS |
+ MMU_FTR_USE_TLBILX,
+ .icache_bsize = 64,
+ .dcache_bsize = 64,
+ .num_pmcs = 4,
+ .oprofile_cpu_type = "ppc/e6500",
+ .oprofile_type = PPC_OPROFILE_FSL_EMB,
+ .cpu_setup = __setup_cpu_e5500,
+ .cpu_restore = __restore_cpu_e5500,
+ .machine_check = machine_check_e500mc,
+ .platform = "ppce6500",
+ },
#ifdef CONFIG_PPC32
{ /* default match */
.pvr_mask = 0x00000000,
--
1.7.3.4
^ permalink raw reply related
* Re: [PATCH] powerpc/booke64: Configurable lazy interrupt disabling
From: Benjamin Herrenschmidt @ 2012-01-18 21:10 UTC (permalink / raw)
To: Laurentiu Tudor; +Cc: linuxppc-dev
In-Reply-To: <1326897306-3924-1-git-send-email-Laurentiu.Tudor@freescale.com>
On Wed, 2012-01-18 at 16:35 +0200, Laurentiu Tudor wrote:
> This patch adds a menuconfig option that allows controlling
> the lazy interrupt disabling feature implemented by this
> commit:
>
> commit d04c56f73c30a5e593202ecfcf25ed43d42363a2
> Author: Paul Mackerras
> Date: Wed Oct 4 16:47:49 2006 +1000
>
> [POWERPC] Lazy interrupt disabling for 64-bit machines
>
> The code in 'powerpc/include/asm/hw_irq.h' was rearranged and
> cleaned-up a bit in order to reduce the number of needed #ifdef's.
It's still nasty. Do you have numbers showing that it's worth disabling
on BookE ?
Cheers,
Ben.
> Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
> ---
> Patch is against
> git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git next
>
> arch/powerpc/Kconfig | 16 ++++++
> arch/powerpc/include/asm/hw_irq.h | 86 ++++++++++++++--------------------
> arch/powerpc/include/asm/irqflags.h | 22 +++++++++
> arch/powerpc/include/asm/paca.h | 4 ++
> arch/powerpc/kernel/asm-offsets.c | 3 +
> arch/powerpc/kernel/entry_64.S | 4 ++
> arch/powerpc/kernel/exceptions-64e.S | 36 +++++++++++---
> arch/powerpc/kernel/head_64.S | 10 ++++
> arch/powerpc/kernel/idle_book3e.S | 7 +++
> arch/powerpc/kernel/irq.c | 5 ++
> arch/powerpc/kernel/setup_64.c | 2 +
> 11 files changed, 138 insertions(+), 57 deletions(-)
>
> diff --git a/arch/powerpc/Kconfig b/arch/powerpc/Kconfig
> index ce5e045..2792278 100644
> --- a/arch/powerpc/Kconfig
> +++ b/arch/powerpc/Kconfig
> @@ -609,6 +609,22 @@ config SECCOMP
>
> If unsure, say Y. Only embedded should say N here.
>
> +config PPC_LAZY_EE
> + bool
> + prompt "Lazy interrupt disabling" if PPC_BOOK3E_64
> + default y if PPC_BOOK3S_64
> + help
> + Local interrupt disabling functions don't disable
> + interrupts right away and instead just clear an
> + internal 'interrupts are enabled' flag. If an
> + interrupt is triggered during this time, the
> + interrupt handling code checks the flag, and if
> + interrupts are supposed to be off, disables them
> + for real and returns, skipping interrupt handling.
> + When interrupts are enabled back, the interrupt
> + fires again and this time gets handled.
> +
> + If unsure, say N.
> endmenu
>
> config ISA_DMA_API
> diff --git a/arch/powerpc/include/asm/hw_irq.h b/arch/powerpc/include/asm/hw_irq.h
> index bb712c9..6f32593 100644
> --- a/arch/powerpc/include/asm/hw_irq.h
> +++ b/arch/powerpc/include/asm/hw_irq.h
> @@ -13,7 +13,20 @@
>
> extern void timer_interrupt(struct pt_regs *);
>
> +#ifdef CONFIG_BOOKE
> +#define __hard_irq_enable() asm volatile("wrteei 1" : : : "memory");
> +#define __hard_irq_disable() asm volatile("wrteei 0" : : : "memory");
> +#else
> #ifdef CONFIG_PPC64
> +#define __hard_irq_enable() __mtmsrd(mfmsr() | MSR_EE, 1)
> +#define __hard_irq_disable() __mtmsrd(mfmsr() & ~MSR_EE, 1)
> +#else
> +#define __hard_irq_enable() mtmsr(mfmsr() | MSR_EE)
> +#define __hard_irq_disable() mtmsr(mfmsr() & ~MSR_EE)
> +#endif
> +#endif /* CONFIG_BOOKE */
> +
> +#if defined(CONFIG_PPC64) && defined(CONFIG_PPC_LAZY_EE)
> #include <asm/paca.h>
>
> static inline unsigned long arch_local_save_flags(void)
> @@ -49,9 +62,11 @@ static inline void arch_local_irq_enable(void)
> arch_local_irq_restore(1);
> }
>
> -static inline unsigned long arch_local_irq_save(void)
> +static inline void hard_irq_disable(void)
> {
> - return arch_local_irq_disable();
> + __hard_irq_disable();
> + get_paca()->soft_enabled = 0;
> + get_paca()->hard_enabled = 0;
> }
>
> static inline bool arch_irqs_disabled_flags(unsigned long flags)
> @@ -59,29 +74,7 @@ static inline bool arch_irqs_disabled_flags(unsigned long flags)
> return flags == 0;
> }
>
> -static inline bool arch_irqs_disabled(void)
> -{
> - return arch_irqs_disabled_flags(arch_local_save_flags());
> -}
> -
> -#ifdef CONFIG_PPC_BOOK3E
> -#define __hard_irq_enable() asm volatile("wrteei 1" : : : "memory");
> -#define __hard_irq_disable() asm volatile("wrteei 0" : : : "memory");
> -#else
> -#define __hard_irq_enable() __mtmsrd(mfmsr() | MSR_EE, 1)
> -#define __hard_irq_disable() __mtmsrd(mfmsr() & ~MSR_EE, 1)
> -#endif
> -
> -#define hard_irq_disable() \
> - do { \
> - __hard_irq_disable(); \
> - get_paca()->soft_enabled = 0; \
> - get_paca()->hard_enabled = 0; \
> - } while(0)
> -
> -#else /* CONFIG_PPC64 */
> -
> -#define SET_MSR_EE(x) mtmsr(x)
> +#else /* CONFIG_PPC64 && CONFIG_PPC_LAZY_EE */
>
> static inline unsigned long arch_local_save_flags(void)
> {
> @@ -97,34 +90,24 @@ static inline void arch_local_irq_restore(unsigned long flags)
> #endif
> }
>
> -static inline unsigned long arch_local_irq_save(void)
> +static inline void arch_local_irq_enable(void)
> {
> - unsigned long flags = arch_local_save_flags();
> -#ifdef CONFIG_BOOKE
> - asm volatile("wrteei 0" : : : "memory");
> -#else
> - SET_MSR_EE(flags & ~MSR_EE);
> -#endif
> - return flags;
> + __hard_irq_enable();
> }
>
> -static inline void arch_local_irq_disable(void)
> +static inline unsigned long arch_local_irq_disable(void)
> {
> -#ifdef CONFIG_BOOKE
> - asm volatile("wrteei 0" : : : "memory");
> -#else
> - arch_local_irq_save();
> -#endif
> + unsigned long flags;
> +
> + flags = arch_local_save_flags();
> + __hard_irq_disable();
> +
> + return flags;
> }
>
> -static inline void arch_local_irq_enable(void)
> +static inline void hard_irq_disable(void)
> {
> -#ifdef CONFIG_BOOKE
> - asm volatile("wrteei 1" : : : "memory");
> -#else
> - unsigned long msr = mfmsr();
> - SET_MSR_EE(msr | MSR_EE);
> -#endif
> + __hard_irq_disable();
> }
>
> static inline bool arch_irqs_disabled_flags(unsigned long flags)
> @@ -132,15 +115,18 @@ static inline bool arch_irqs_disabled_flags(unsigned long flags)
> return (flags & MSR_EE) == 0;
> }
>
> +#endif /* CONFIG_PPC64 && CONFIG_PPC_LAZY_EE */
> +
> +static inline unsigned long arch_local_irq_save(void)
> +{
> + return arch_local_irq_disable();
> +}
> +
> static inline bool arch_irqs_disabled(void)
> {
> return arch_irqs_disabled_flags(arch_local_save_flags());
> }
>
> -#define hard_irq_disable() arch_local_irq_disable()
> -
> -#endif /* CONFIG_PPC64 */
> -
> #define ARCH_IRQ_INIT_FLAGS IRQ_NOREQUEST
>
> /*
> diff --git a/arch/powerpc/include/asm/irqflags.h b/arch/powerpc/include/asm/irqflags.h
> index b0b06d8..9685b75c 100644
> --- a/arch/powerpc/include/asm/irqflags.h
> +++ b/arch/powerpc/include/asm/irqflags.h
> @@ -39,6 +39,8 @@
> #define TRACE_ENABLE_INTS TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_on)
> #define TRACE_DISABLE_INTS TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_off)
>
> +#ifdef CONFIG_PPC_LAZY_EE
> +
> #define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip) \
> cmpdi en,0; \
> bne 95f; \
> @@ -51,12 +53,32 @@
> TRACE_AND_RESTORE_IRQ_PARTIAL(en,96f); \
> stb en,PACASOFTIRQEN(r13); \
> 96:
> +
> +#else /* CONFIG_PPC_LAZY_EE */
> +
> +#define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip) \
> + cmpdi en,0; \
> + bne 95f; \
> + TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_off) \
> + b skip; \
> +95: TRACE_WITH_FRAME_BUFFER(.trace_hardirqs_on) \
> + li en,1;
> +#define TRACE_AND_RESTORE_IRQ(en) \
> + TRACE_AND_RESTORE_IRQ_PARTIAL(en,96f); \
> +96:
> +
> +#endif /* CONFIG_PPC_LAZY_EE */
> +
> #else
> #define TRACE_ENABLE_INTS
> #define TRACE_DISABLE_INTS
> #define TRACE_AND_RESTORE_IRQ_PARTIAL(en,skip)
> +#ifdef CONFIG_PPC_LAZY_EE
> #define TRACE_AND_RESTORE_IRQ(en) \
> stb en,PACASOFTIRQEN(r13)
> +#else
> +#define TRACE_AND_RESTORE_IRQ(en)
> +#endif
> #endif
> #endif
>
> diff --git a/arch/powerpc/include/asm/paca.h b/arch/powerpc/include/asm/paca.h
> index 269c05a..b74c2b1 100644
> --- a/arch/powerpc/include/asm/paca.h
> +++ b/arch/powerpc/include/asm/paca.h
> @@ -131,8 +131,12 @@ struct paca_struct {
> u64 saved_r1; /* r1 save for RTAS calls or PM */
> u64 saved_msr; /* MSR saved here by enter_rtas */
> u16 trap_save; /* Used when bad stack is encountered */
> +
> +#ifdef CONFIG_PPC_LAZY_EE
> u8 soft_enabled; /* irq soft-enable flag */
> u8 hard_enabled; /* set if irqs are enabled in MSR */
> +#endif
> +
> u8 io_sync; /* writel() needs spin_unlock sync */
> u8 irq_work_pending; /* IRQ_WORK interrupt while soft-disable */
> u8 nap_state_lost; /* NV GPR values lost in power7_idle */
> diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c
> index 04caee7..5b1fac9 100644
> --- a/arch/powerpc/kernel/asm-offsets.c
> +++ b/arch/powerpc/kernel/asm-offsets.c
> @@ -146,8 +146,11 @@ int main(void)
> DEFINE(PACATOC, offsetof(struct paca_struct, kernel_toc));
> DEFINE(PACAKBASE, offsetof(struct paca_struct, kernelbase));
> DEFINE(PACAKMSR, offsetof(struct paca_struct, kernel_msr));
> +#ifdef CONFIG_PPC_LAZY_EE
> DEFINE(PACASOFTIRQEN, offsetof(struct paca_struct, soft_enabled));
> DEFINE(PACAHARDIRQEN, offsetof(struct paca_struct, hard_enabled));
> +#endif
> +
> DEFINE(PACACONTEXTID, offsetof(struct paca_struct, context.id));
> #ifdef CONFIG_PPC_MM_SLICES
> DEFINE(PACALOWSLICESPSIZE, offsetof(struct paca_struct,
> diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S
> index d834425..ce7620b 100644
> --- a/arch/powerpc/kernel/entry_64.S
> +++ b/arch/powerpc/kernel/entry_64.S
> @@ -124,8 +124,10 @@ END_FW_FTR_SECTION_IFSET(FW_FEATURE_SPLPAR)
> ld r12,_MSR(r1)
> #endif /* CONFIG_TRACE_IRQFLAGS */
> li r10,1
> +#ifdef CONFIG_PPC_LAZY_EE
> stb r10,PACASOFTIRQEN(r13)
> stb r10,PACAHARDIRQEN(r13)
> +#endif
> std r10,SOFTE(r1)
> #ifdef CONFIG_PPC_ISERIES
> BEGIN_FW_FTR_SECTION
> @@ -602,10 +604,12 @@ ALT_FW_FTR_SECTION_END_IFCLR(FW_FEATURE_ISERIES)
> 2:
> TRACE_AND_RESTORE_IRQ(r5);
>
> +#ifdef CONFIG_PPC_LAZY_EE
> /* extract EE bit and use it to restore paca->hard_enabled */
> ld r3,_MSR(r1)
> rldicl r4,r3,49,63 /* r0 = (r3 >> 15) & 1 */
> stb r4,PACAHARDIRQEN(r13)
> +#endif
>
> #ifdef CONFIG_PPC_BOOK3E
> b .exception_return_book3e
> diff --git a/arch/powerpc/kernel/exceptions-64e.S b/arch/powerpc/kernel/exceptions-64e.S
> index 429983c..d17abb3 100644
> --- a/arch/powerpc/kernel/exceptions-64e.S
> +++ b/arch/powerpc/kernel/exceptions-64e.S
> @@ -96,11 +96,6 @@
> #define PROLOG_ADDITION_NONE_DBG
> #define PROLOG_ADDITION_NONE_MC
>
> -#define PROLOG_ADDITION_MASKABLE_GEN \
> - lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
> - cmpwi cr0,r11,0; /* yes -> go out of line */ \
> - beq masked_interrupt_book3e;
> -
> #define PROLOG_ADDITION_2REGS_GEN \
> std r14,PACA_EXGEN+EX_R14(r13); \
> std r15,PACA_EXGEN+EX_R15(r13)
> @@ -120,11 +115,29 @@
> std r14,PACA_EXMC+EX_R14(r13); \
> std r15,PACA_EXMC+EX_R15(r13)
>
> +#ifdef CONFIG_PPC_LAZY_EE
> +#define PROLOG_ADDITION_MASKABLE_GEN \
> + lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
> + cmpwi cr0,r11,0; /* yes -> go out of line */ \
> + beq masked_interrupt_book3e;
> +
> #define PROLOG_ADDITION_DOORBELL_GEN \
> lbz r11,PACASOFTIRQEN(r13); /* are irqs soft-disabled ? */ \
> cmpwi cr0,r11,0; /* yes -> go out of line */ \
> beq masked_doorbell_book3e
> -
> +#else /* CONFIG_PPC_LAZY_EE */
> +#define PROLOG_ADDITION_MASKABLE_GEN
> +#define PROLOG_ADDITION_DOORBELL_GEN
> +#endif /* CONFIG_PPC_LAZY_EE */
> +
> +#ifdef CONFIG_PPC_LAZY_EE
> +#define GET_IRQ_SOFT_ENABLED \
> + lbz r11,PACASOFTIRQEN(r13)
> +#else
> +#define GET_IRQ_SOFT_ENABLED \
> + mfmsr r11; \
> + rlwimi r11,r11,0,16,16
> +#endif
>
> /* Core exception code for all exceptions except TLB misses.
> * XXX: Needs to make SPRN_SPRG_GEN depend on exception type
> @@ -148,7 +161,7 @@
> mfspr r8,SPRN_XER; /* save XER in stackframe */ \
> ld r9,excf+EX_R1(r13); /* load orig r1 back from PACA */ \
> lwz r10,excf+EX_CR(r13); /* load orig CR back from PACA */ \
> - lbz r11,PACASOFTIRQEN(r13); /* get current IRQ softe */ \
> + GET_IRQ_SOFT_ENABLED; /* get current IRQ softe */ \
> ld r12,exception_marker@toc(r2); \
> li r0,0; \
> std r3,GPR10(r1); /* save r10 to stackframe */ \
> @@ -169,11 +182,18 @@
>
> /* Variants for the "ints" argument */
> #define INTS_KEEP
> +
> +#ifdef CONFIG_PPC_LAZY_EE
> #define INTS_DISABLE_SOFT \
> stb r0,PACASOFTIRQEN(r13); /* mark interrupts soft-disabled */ \
> TRACE_DISABLE_INTS;
> #define INTS_DISABLE_HARD \
> stb r0,PACAHARDIRQEN(r13); /* and hard disabled */
> +#else
> +#define INTS_DISABLE_SOFT
> +#define INTS_DISABLE_HARD
> +#endif
> +
> #define INTS_DISABLE_ALL \
> INTS_DISABLE_SOFT \
> INTS_DISABLE_HARD
> @@ -553,6 +573,7 @@ kernel_dbg_exc:
> MASKABLE_EXCEPTION(0x320, ehpriv, .unknown_exception, ACK_NONE)
>
>
> +#ifdef CONFIG_PPC_LAZY_EE
> /*
> * An interrupt came in while soft-disabled; clear EE in SRR1,
> * clear paca->hard_enabled and return.
> @@ -577,6 +598,7 @@ masked_interrupt_book3e_common:
> mfspr r13,SPRN_SPRG_GEN_SCRATCH;
> rfi
> b .
> +#endif /* CONFIG_PPC_LAZY_EE */
>
> /*
> * This is called from 0x300 and 0x400 handlers after the prologs with
> diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S
> index 06c7251..017d669 100644
> --- a/arch/powerpc/kernel/head_64.S
> +++ b/arch/powerpc/kernel/head_64.S
> @@ -559,12 +559,14 @@ _GLOBAL(pmac_secondary_start)
> add r13,r13,r4 /* for this processor. */
> SET_PACA(r13) /* Save vaddr of paca in an SPRG*/
>
> +#ifdef CONFIG_PPC_LAZY_EE
> /* Mark interrupts soft and hard disabled (they might be enabled
> * in the PACA when doing hotplug)
> */
> li r0,0
> stb r0,PACASOFTIRQEN(r13)
> stb r0,PACAHARDIRQEN(r13)
> +#endif
>
> /* Create a temp kernel stack for use before relocation is on. */
> ld r1,PACAEMERGSP(r13)
> @@ -621,14 +623,18 @@ __secondary_start:
> #ifdef CONFIG_PPC_ISERIES
> BEGIN_FW_FTR_SECTION
> ori r4,r4,MSR_EE
> +#ifdef CONFIG_PPC_LAZY_EE
> li r8,1
> stb r8,PACAHARDIRQEN(r13)
> +#endif
> END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
> #endif
> +#ifdef CONFIG_PPC_LAZY_EE
> BEGIN_FW_FTR_SECTION
> stb r7,PACAHARDIRQEN(r13)
> END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES)
> stb r7,PACASOFTIRQEN(r13)
> +#endif
>
> mtspr SPRN_SRR0,r3
> mtspr SPRN_SRR1,r4
> @@ -775,8 +781,10 @@ _INIT_GLOBAL(start_here_common)
>
> /* Load up the kernel context */
> 5:
> +#ifdef CONFIG_PPC_LAZY_EE
> li r5,0
> stb r5,PACASOFTIRQEN(r13) /* Soft Disabled */
> +#endif
> #ifdef CONFIG_PPC_ISERIES
> BEGIN_FW_FTR_SECTION
> mfmsr r5
> @@ -785,7 +793,9 @@ BEGIN_FW_FTR_SECTION
> li r5,1
> END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES)
> #endif
> +#ifdef CONFIG_PPC_LAZY_EE
> stb r5,PACAHARDIRQEN(r13) /* Hard Disabled on others */
> +#endif
>
> bl .start_kernel
>
> diff --git a/arch/powerpc/kernel/idle_book3e.S b/arch/powerpc/kernel/idle_book3e.S
> index 16c002d..34b09e0 100644
> --- a/arch/powerpc/kernel/idle_book3e.S
> +++ b/arch/powerpc/kernel/idle_book3e.S
> @@ -28,6 +28,7 @@ _GLOBAL(book3e_idle)
> /* Hard disable interrupts */
> wrteei 0
>
> +#ifdef CONFIG_PPC_LAZY_EE
> /* Now check if an interrupt came in while we were soft disabled
> * since we may otherwise lose it (doorbells etc...). We know
> * that since PACAHARDIRQEN will have been cleared in that case.
> @@ -35,6 +36,7 @@ _GLOBAL(book3e_idle)
> lbz r3,PACAHARDIRQEN(r13)
> cmpwi cr0,r3,0
> beqlr
> +#endif
>
> /* Now we are going to mark ourselves as soft and hard enables in
> * order to be able to take interrupts while asleep. We inform lockdep
> @@ -44,9 +46,12 @@ _GLOBAL(book3e_idle)
> stdu r1,-128(r1)
> bl .trace_hardirqs_on
> #endif
> +
> +#ifdef CONFIG_PPC_LAZY_EE
> li r0,1
> stb r0,PACASOFTIRQEN(r13)
> stb r0,PACAHARDIRQEN(r13)
> +#endif
>
> /* Interrupts will make use return to LR, so get something we want
> * in there
> @@ -56,10 +61,12 @@ _GLOBAL(book3e_idle)
> /* Hard disable interrupts again */
> wrteei 0
>
> +#ifdef CONFIG_PPC_LAZY_EE
> /* Mark them off again in the PACA as well */
> li r0,0
> stb r0,PACASOFTIRQEN(r13)
> stb r0,PACAHARDIRQEN(r13)
> +#endif
>
> /* Tell lockdep about it */
> #ifdef CONFIG_TRACE_IRQFLAGS
> diff --git a/arch/powerpc/kernel/irq.c b/arch/powerpc/kernel/irq.c
> index 701d4ac..e2d1784 100644
> --- a/arch/powerpc/kernel/irq.c
> +++ b/arch/powerpc/kernel/irq.c
> @@ -99,6 +99,8 @@ EXPORT_SYMBOL(irq_desc);
>
> int distribute_irqs = 1;
>
> +#ifdef CONFIG_PPC_LAZY_EE
> +
> static inline notrace unsigned long get_hard_enabled(void)
> {
> unsigned long enabled;
> @@ -193,6 +195,9 @@ notrace void arch_local_irq_restore(unsigned long en)
> __hard_irq_enable();
> }
> EXPORT_SYMBOL(arch_local_irq_restore);
> +
> +#endif /* CONFIG_PPC_LAZY_EE */
> +
> #endif /* CONFIG_PPC64 */
>
> int arch_show_interrupts(struct seq_file *p, int prec)
> diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c
> index 4cb8f1e..06f5b19 100644
> --- a/arch/powerpc/kernel/setup_64.c
> +++ b/arch/powerpc/kernel/setup_64.c
> @@ -233,8 +233,10 @@ void __init early_setup(unsigned long dt_ptr)
> #ifdef CONFIG_SMP
> void early_setup_secondary(void)
> {
> +#ifdef CONFIG_PPC_LAZY_EE
> /* Mark interrupts enabled in PACA */
> get_paca()->soft_enabled = 0;
> +#endif
>
> /* Initialize the hash table or TLB handling */
> early_init_mmu_secondary();
^ permalink raw reply
* [PATCH 1/2] powerpc/dts: Add dts for p1020rdb-pc
From: Zhicheng Fan @ 2012-01-19 9:06 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Fanzc
From: Fanzc <b32736@freeescale.com>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Fanzc <b32736@freeescale.com>
---
arch/powerpc/boot/dts/p1020rdb-pc.dts | 67 ++++++
arch/powerpc/boot/dts/p1020rdb-pc.dtsi | 251 ++++++++++++++++++++++
arch/powerpc/boot/dts/p1020rdb-pc_36b.dts | 67 ++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts | 63 ++++++
arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts | 141 ++++++++++++
5 files changed, 589 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc.dtsi
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
create mode 100644 arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc.dts b/arch/powerpc/boot/dts/p1020rdb-pc.dts
new file mode 100644
index 0000000..e283b94
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc.dts
@@ -0,0 +1,67 @@
+/*
+ * P1020 RDB-PC Device Tree Source
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000
+ 0x2 0x0 0x0 0xffb00000 0x00020000
+ 0x3 0x0 0x0 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb-pc.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc.dtsi b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
new file mode 100644
index 0000000..1c4003f
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc.dtsi
@@ -0,0 +1,251 @@
+/*
+ * P1020 RDB-PC Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x1000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg = <0x0 0x00040000>;
+ label = "NOR (RO) Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg = <0x00040000 0x00040000>;
+ label = "NOR (RO) DTB Image";
+ read-only;
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg = <0x00080000 0x00380000>;
+ label = "NOR (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg = <0x00400000 0x00b00000>;
+ label = "NOR (RW) JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg = <0x00f00000 0x00100000>;
+ label = "NOR (RO) U-Boot Image";
+ read-only;
+ };
+ };
+
+ nand@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,p1020-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg = <0x0 0x00100000>;
+ label = "NAND (RO) U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg = <0x00100000 0x00100000>;
+ label = "NAND (RO) DTB Image";
+ read-only;
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00200000 0x00400000>;
+ label = "NAND (RO) Linux Kernel Image";
+ read-only;
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg = <0x00600000 0x00400000>;
+ label = "NAND (RO) Compressed RFS Image";
+ read-only;
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg = <0x00a00000 0x00700000>;
+ label = "NAND (RW) JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for JFFS2 based Root file System */
+ reg = <0x01100000 0x00f00000>;
+ label = "NAND (RW) Writable User area";
+ };
+ };
+
+ L2switch@2,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "vitesse-7385";
+ reg = <0x2 0x0 0x20000>;
+ };
+
+ cpld@3,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cpld";
+ reg = <0x3 0x0 0x20000>;
+ read-only;
+ };
+};
+
+&soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg = <0x0 0x00080000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image*/
+ reg = <0x00080000 0x00080000>;
+ label = "dtb";
+ read-only;
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg = <0x00100000 0x00400000>;
+ label = "kernel";
+ read-only;
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg = <0x00500000 0x00400000>;
+ label = "file system";
+ read-only;
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg = <0x00900000 0x00700000>;
+ label = "file system jffs2";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type = "ulpi";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <3 1>;
+ reg = <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ };
+
+ tbi-phy@2 {
+ device_type = "tbi-phy";
+ reg = <0x2>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link = <1 1 1000 0 0>;
+ phy-connection-type = "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle = <&phy0>;
+ tbi-handle = <&tbi1>;
+ phy-connection-type = "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle = <&phy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
new file mode 100644
index 0000000..dfe0ddc
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_36b.dts
@@ -0,0 +1,67 @@
+/*
+ * P1020 RDB-PC Device Tree Source (36-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC";
+
+ memory {
+ device_type = "memory";
+ };
+
+ lbc: localbus@fffe05000 {
+ reg = <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges = <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000
+ 0x2 0x0 0xf 0xffb00000 0x00040000
+ 0x3 0x0 0xf 0xffa00000 0x00020000>;
+ };
+
+ soc: soc@fffe00000 {
+ ranges = <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ reg = <0xf 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg = <0xf 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+};
+
+/include/ "p1020rdb.dtsi"
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
new file mode 100644
index 0000000..906c932
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core0.dts
@@ -0,0 +1,63 @@
+/*
+ * P1020 RDB-PC Core0 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts file allows core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb,
+ * eth1, eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
+ *
+ * Please note to add "-b 0" for core0's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC", "fsl,MPC85XXRDB-CAMP";
+
+ aliases {
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ serial0 = &serial0;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ PowerPC,P1020@1 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ serial1: serial@4600 {
+ status = "disabled";
+ };
+
+ enet0: ethernet@b0000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 42 29 30 34 /* serial1, enet0-queue-group0 */
+ 17 18 24 45 /* enet0-queue-group1, crypto */
+ >;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
new file mode 100644
index 0000000..7f7232b
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1020rdb-pc_camp_core1.dts
@@ -0,0 +1,141 @@
+/*
+ * P1020 RDB-PC Core1 Device Tree Source in CAMP mode.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts allows core1 to have l2, eth0, crypto.
+ *
+ * Please note to add "-b 1" for core1's dts compiling.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/include/ "p1020rdb-pc.dts"
+
+/ {
+ model = "fsl,P1020RDB-PC";
+ compatible = "fsl,P1020RDB-PC", "fsl,MPC85XXRDB-CAMP";
+
+ aliases {
+ ethernet0 = &enet0;
+ serial0 = &serial1;
+ };
+
+ cpus {
+ PowerPC,P1020@0 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ ecm-law@0 {
+ status = "disabled";
+ };
+
+ ecm@1000 {
+ status = "disabled";
+ };
+
+ memory-controller@2000 {
+ status = "disabled";
+ };
+
+ i2c@3000 {
+ status = "disabled";
+ };
+
+ i2c@3100 {
+ status = "disabled";
+ };
+
+ serial0: serial@4500 {
+ status = "disabled";
+ };
+
+ spi@7000 {
+ status = "disabled";
+ };
+
+ gpio: gpio-controller@f000 {
+ status = "disabled";
+ };
+
+ dma@21300 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ status = "disabled";
+ };
+
+ mdio@25000 {
+ status = "disabled";
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ usb@22000 {
+ status = "disabled";
+ };
+
+ sdhci@2e000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 16 /* ecm, mem, L2, pci0, pci1 */
+ 43 42 59 /* i2c, serial0, spi */
+ 47 63 62 /* gpio, tdm */
+ 20 21 22 23 /* dma */
+ 03 02 /* mdio */
+ 35 36 40 /* enet1-queue-group0 */
+ 51 52 67 /* enet1-queue-group1 */
+ 31 32 33 /* enet2-queue-group0 */
+ 25 26 27 /* enet2-queue-group1 */
+ 28 72 58 /* usb, sdhci, crypto */
+ 0xb0 0xb1 0xb2 /* message */
+ 0xb3 0xb4 0xb5
+ 0xb6 0xb7
+ 0xe0 0xe1 0xe2 /* msi */
+ 0xe3 0xe4 0xe5
+ 0xe6 0xe7 /* sdhci, crypto , pci */
+ >;
+ };
+
+ msi@41600 {
+ status = "disabled";
+ };
+
+ global-utilities@e0000 { //global utilities block
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ status = "disabled";
+ };
+
+ pci1: pcie@ffe0a000 {
+ status = "disabled";
+ };
+};
--
1.7.0.4
^ permalink raw reply related
* [PATCH 2/2] P1020RDB-PC: Add p1020rdb-pc platform support
From: Zhicheng Fan @ 2012-01-19 9:06 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Fanzc
In-Reply-To: <1326964017-615-1-git-send-email-B32736@freescale.com>
From: Fanzc <b32736@freeescale.com>
Signed-off-by: Fanzc <b32736@freeescale.com>
---
arch/powerpc/platforms/85xx/mpc85xx_rdb.c | 27 ++++++++++++++++++++++++++-
1 files changed, 26 insertions(+), 1 deletions(-)
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
index ccf520e..0583d38 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
@@ -1,7 +1,7 @@
/*
* MPC85xx RDB Board Setup
*
- * Copyright 2009 Freescale Semiconductor Inc.
+ * Copyright 2009,2012 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -90,6 +90,7 @@ static void __init mpc85xx_rdb_setup_arch(void)
machine_device_initcall(p2020_rdb, mpc85xx_common_publish_devices);
machine_device_initcall(p1020_rdb, mpc85xx_common_publish_devices);
+machine_device_initcall(p1020_rdb_pc, mpc85xx_common_publish_devices);
/*
* Called very early, device-tree isn't unflattened
@@ -112,6 +113,15 @@ static int __init p1020_rdb_probe(void)
return 0;
}
+static int __init p1020_rdb_pc_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ if (of_flat_dt_is_compatible(root, "fsl,P1020RDB-PC"))
+ return 1;
+ return 0;
+}
+
define_machine(p2020_rdb) {
.name = "P2020 RDB",
.probe = p2020_rdb_probe,
@@ -139,3 +149,18 @@ define_machine(p1020_rdb) {
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
};
+
+define_machine(p1020_rdb_pc) {
+ .name = "P1020RDB-PC",
+ .probe = p1020_rdb_pc_probe,
+ .setup_arch = mpc85xx_rdb_setup_arch,
+ .init_IRQ = mpc85xx_rdb_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+#endif
+ .get_irq = mpic_get_irq,
+ .restart = fsl_rstcr_restart,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
+
--
1.7.0.4
^ permalink raw reply related
* Re: Problem with full speed devices on PowerPC MPC5121 host port
From: Anatolij Gustschin @ 2012-01-19 9:34 UTC (permalink / raw)
To: Matthias Fuchs; +Cc: linuxppc-dev, linux-usb
In-Reply-To: <4F16CC3C.6060005@esd.eu>
Hi Matthias,
On Wed, 18 Jan 2012 14:42:20 +0100
Matthias Fuchs <matthias.fuchs@esd.eu> wrote:
...
> > Can you try the attached patch? Does it have an impact?
>
> Yes, in deed, it solved my problem :-) Finally I noticed that
> the problem is listed in the CPU's errata document.
>
> You could update the comment and commit message to "... when there is
> heavy simultaneus PATA write or network activity".
>
> I vote for getting this mainline.
>
> Tested-by: Matthias Fuchs <matthias.fuchs@esd.ue>
Thanks for testing! I'll rework to remove ifdef in the patch
and fix commit message and then resubmit.
Anatolij
^ permalink raw reply
* Re: [PATCH] powerpc/booke64: Configurable lazy interrupt disabling
From: Tudor Laurentiu @ 2012-01-19 13:18 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: linuxppc-dev
In-Reply-To: <1326921026.26116.34.camel@pasglop>
Hi Ben,
On 01/18/2012 11:10 PM, Benjamin Herrenschmidt wrote:
> On Wed, 2012-01-18 at 16:35 +0200, Laurentiu Tudor wrote:
>> This patch adds a menuconfig option that allows controlling
>> the lazy interrupt disabling feature implemented by this
>> commit:
>>
>> commit d04c56f73c30a5e593202ecfcf25ed43d42363a2
>> Author: Paul Mackerras
>> Date: Wed Oct 4 16:47:49 2006 +1000
>>
>> [POWERPC] Lazy interrupt disabling for 64-bit machines
>>
>> The code in 'powerpc/include/asm/hw_irq.h' was rearranged and
>> cleaned-up a bit in order to reduce the number of needed #ifdef's.
>
> It's still nasty.
Yep, there is still room for improvement. Perhaps trimming some of those
various interrupt enable/disable functions & macros. However I don't
think I have enough experience to do this ... so, any suggestions are
welcomed.
> Do you have numbers showing that it's worth disabling
> on BookE ?
On fsl's p5020 there should be some performance gains because disabling
"lazy ee" allows enabling the "external proxy" feature.
The thing is I can't prove this because I have no idea what benchmark to
run. Let me know if you guys know of any relevant benchmark I could try.
---
Best Regards, Laurentiu
^ permalink raw reply
* Re: [PATCH] powerpc/booke64: Configurable lazy interrupt disabling
From: Stuart Yoder @ 2012-01-19 19:21 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: Laurentiu Tudor, linuxppc-dev
In-Reply-To: <1326921026.26116.34.camel@pasglop>
On Wed, Jan 18, 2012 at 3:10 PM, Benjamin Herrenschmidt
<benh@kernel.crashing.org> wrote:
> On Wed, 2012-01-18 at 16:35 +0200, Laurentiu Tudor wrote:
>> This patch adds a menuconfig option that allows controlling
>> the lazy interrupt disabling feature implemented by this
>> commit:
>>
>> commit d04c56f73c30a5e593202ecfcf25ed43d42363a2
>> Author: Paul Mackerras
>> Date: =A0 Wed Oct 4 16:47:49 2006 +1000
>>
>> =A0 =A0 [POWERPC] Lazy interrupt disabling for 64-bit machines
>>
>> The code in 'powerpc/include/asm/hw_irq.h' was rearranged and
>> cleaned-up a bit in order to reduce the number of needed #ifdef's.
>
> It's still nasty. Do you have numbers showing that it's worth disabling
> on BookE ?
It's not just about bare metal performance-- some platforms such as
the Freescale
Topaz hypervisor don't provide legacy IACK type interrupt
acknowledgment, and expect
the guest to support the external proxy mechanism.
With Topaz, interrupts go directly to guests and we don't want to require a
trap/hcall to do an IACK, as that adds potentially thousands of cycles of
latency to every interrupt.
As you know, with external proxy interrupts are acknowledged by the
hardware and it becomes problematic to replay the interrupt in
the context of lazy EE when interrupts are re-enabled. The interrupt
will not fire again when you enable EE.
That is currently the issue, as we can't run the 64-bit kernel on Topaz.
Our option are:
1) to provide an option to disable lazy EE
2) do some kind of hack to replay interrupts with lazy EE
3) change Topaz to support legacy IACK, but this gets ugly for
various reasons.
Providing a config option to disable lazy EE seemed to be a good
approach.
Stuart
^ permalink raw reply
* Re: [PATCH] powerpc/booke64: Configurable lazy interrupt disabling
From: Stuart Yoder @ 2012-01-19 19:29 UTC (permalink / raw)
To: Benjamin Herrenschmidt; +Cc: Laurentiu Tudor, linuxppc-dev
In-Reply-To: <CALRxmdC_E4Z==4R_2MGHAi3T7mdF9oHx3rBE6Meb+3R1gWF5VQ@mail.gmail.com>
On Thu, Jan 19, 2012 at 1:21 PM, Stuart Yoder <b08248@gmail.com> wrote:
> On Wed, Jan 18, 2012 at 3:10 PM, Benjamin Herrenschmidt
> <benh@kernel.crashing.org> wrote:
>> On Wed, 2012-01-18 at 16:35 +0200, Laurentiu Tudor wrote:
>>> This patch adds a menuconfig option that allows controlling
>>> the lazy interrupt disabling feature implemented by this
>>> commit:
>>>
>>> commit d04c56f73c30a5e593202ecfcf25ed43d42363a2
>>> Author: Paul Mackerras
>>> Date: =A0 Wed Oct 4 16:47:49 2006 +1000
>>>
>>> =A0 =A0 [POWERPC] Lazy interrupt disabling for 64-bit machines
>>>
>>> The code in 'powerpc/include/asm/hw_irq.h' was rearranged and
>>> cleaned-up a bit in order to reduce the number of needed #ifdef's.
>>
>> It's still nasty. Do you have numbers showing that it's worth disabling
>> on BookE ?
>
> It's not just about bare metal performance-- some platforms such as
> the Freescale
> Topaz hypervisor don't provide legacy IACK type interrupt
> acknowledgment, and expect
> the guest to support the external proxy mechanism.
>
> With Topaz, interrupts go directly to guests and we don't want to require=
a
> trap/hcall to do an IACK, as that adds potentially thousands of cycles of
> latency to every interrupt.
>
> As you know, with external proxy interrupts are acknowledged by the
> hardware and it becomes problematic to replay the interrupt in
> the context of lazy EE when interrupts are re-enabled. =A0 The interrupt
> will not fire again when you enable EE.
>
> That is currently the issue, as we can't run the 64-bit kernel on Topaz.
> Our option are:
> =A01) to provide an option to disable lazy EE
> =A02) do some kind of hack to replay interrupts with lazy EE
> =A03) change Topaz to support legacy IACK, but this gets ugly for
> =A0 =A0 =A0various reasons.
>
> Providing a config option to disable lazy EE seemed to be a good
> approach.
Also, Scott had posted an approach to do option #2 a while back,
but as I recall there was some negative feedback about this. See:
<http://lists.ozlabs.org/pipermail/linuxppc-dev/2011-August/092103.html>
Stuart
^ permalink raw reply
* ata/ide driver for MPC512x
From: Matthias Fuchs @ 2012-01-19 21:28 UTC (permalink / raw)
To: linuxppc-dev
Hi,
do we have an ata/ide driver for MPC512x internal ATA controller?
So something that is compatible to "fsl,mpc5121-pata"?
Matthias
^ permalink raw reply
* [PATCH] powerpc/85xx: fix Kconfig warning about missing 8250 dependency
From: Paul Gortmaker @ 2012-01-20 1:23 UTC (permalink / raw)
To: galak, benh, paulus; +Cc: Paul Gortmaker, linuxppc-dev
The SERIAL_8250_EXTENDED option just enables access to other
less regularly used options, like SERIAL_8250_SHARE_IRQ.
Select it to get rid of this warning when selecting the child
option living underneath it.
warning: (FSL_SOC_BOOKE && SERIAL_8250_RM9K) selects
SERIAL_8250_SHARE_IRQ which has unmet direct dependencies
(HAS_IOMEM && SERIAL_8250_EXTENDED)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
diff --git a/arch/powerpc/platforms/85xx/Kconfig b/arch/powerpc/platforms/85xx/Kconfig
index d7946be..b221236 100644
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -6,6 +6,7 @@ menuconfig FSL_SOC_BOOKE
select MPIC
select PPC_PCI_CHOICE
select FSL_PCI if PCI
+ select SERIAL_8250_EXTENDED if SERIAL_8250
select SERIAL_8250_SHARE_IRQ if SERIAL_8250
default y
--
1.7.7.2
^ permalink raw reply related
* [PATCH V2] fsl-sata: I/O load balancing
From: qiang.liu @ 2012-01-20 2:19 UTC (permalink / raw)
To: jgarzik, linux-ide; +Cc: Qiang Liu, linuxppc-dev, linux-kernel
From: Qiang Liu <qiang.liu@freescale.com>
Reduce interrupt signals through reset Interrupt Coalescing Control Reg.
Provide dynamic method to adjust interrupt signals and timer ticks by sysfs.
It is a tradeoff for different applications.
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
---
change for V2
support dynamic config interrupt coalescing register by /sysfs
test random small file with iometer
Description:
1. fsl-sata interrupt will be raised 130 thousand times when write 8G file
(dd if=/dev/zero of=/dev/sda2 bs=128K count=65536);
2. most of interrupts raised because of only 1-4 commands completed;
3. only 30 thousand times will be raised after set max interrupt threshold,
more interrupts are coalesced as the description of ICC;
Test methods and results:
1. test sequential large file performance,
[root@p2020ds root]# echo 31 524287 > \
/sys/devices/soc.0/ffe18000.sata/intr_coalescing
[root@p2020ds root]# dd if=/dev/zero of=/dev/sda2 bs=128K count=65536 &
[root@p2020ds root]# top
CPU % | dd | flush-8:0 | softirq
---------------------------------------
before | 20-22 | 17-19 | 7
---------------------------------------
after | 18-21 | 15-16 | 5
---------------------------------------
2. test random small file with iometer,
iometer paramters:
4 I/Os burst length, 1MB transfer request size, 100% write, 2MB file size
as default configuration of interrupt coalescing register, 1 interrupts and
no timeout config, total write performance is 119MB per second,
after config with the maximum value, write performance is 110MB per second.
After compare the test results, a configuable interrupt coalescing should be
better when cope with flexible context.
drivers/ata/sata_fsl.c | 111 ++++++++++++++++++++++++++++++++++++++++++++++--
1 files changed, 107 insertions(+), 4 deletions(-)
diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c
index 3547000..41ca495 100644
--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -6,7 +6,7 @@
* Author: Ashish Kalra <ashish.kalra@freescale.com>
* Li Yang <leoli@freescale.com>
*
- * Copyright (c) 2006-2007, 2011 Freescale Semiconductor, Inc.
+ * Copyright (c) 2006-2007, 2011-2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -26,6 +26,15 @@
#include <asm/io.h>
#include <linux/of_platform.h>
+static unsigned int intr_coalescing_count;
+module_param(intr_coalescing_count, int, S_IRUGO);
+MODULE_PARM_DESC(intr_coalescing_count,
+ "INT coalescing count threshold (1..31)");
+
+static unsigned int intr_coalescing_ticks;
+module_param(intr_coalescing_ticks, int, S_IRUGO);
+MODULE_PARM_DESC(intr_coalescing_ticks,
+ "INT coalescing timer threshold in AHB ticks");
/* Controller information */
enum {
SATA_FSL_QUEUE_DEPTH = 16,
@@ -83,6 +92,16 @@ enum {
};
/*
+ * Interrupt Coalescing Control Register bitdefs */
+enum {
+ ICC_MIN_INT_COUNT_THRESHOLD = 1,
+ ICC_MAX_INT_COUNT_THRESHOLD = ((1 << 5) - 1),
+ ICC_MIN_INT_TICKS_THRESHOLD = 0,
+ ICC_MAX_INT_TICKS_THRESHOLD = ((1 << 19) - 1),
+ ICC_SAFE_INT_TICKS = 1,
+};
+
+/*
* Host Controller command register set - per port
*/
enum {
@@ -263,9 +282,66 @@ struct sata_fsl_host_priv {
int irq;
int data_snoop;
u32 quirks;
+ struct device_attribute intr_coalescing;
#define SATA_FSL_QUIRK_P3P5_ERRATA (1 << 0)
};
+static void fsl_sata_set_irq_coalescing(struct ata_host *host,
+ unsigned int count, unsigned int ticks)
+{
+ struct sata_fsl_host_priv *host_priv = host->private_data;
+ void __iomem *hcr_base = host_priv->hcr_base;
+
+ if (count > ICC_MAX_INT_COUNT_THRESHOLD)
+ count = ICC_MAX_INT_COUNT_THRESHOLD;
+ else if (count < ICC_MIN_INT_COUNT_THRESHOLD)
+ count = ICC_MIN_INT_COUNT_THRESHOLD;
+
+ if (ticks > ICC_MAX_INT_TICKS_THRESHOLD)
+ ticks = ICC_MAX_INT_TICKS_THRESHOLD;
+ else if ((ICC_MIN_INT_TICKS_THRESHOLD == ticks) &&
+ (count > ICC_MIN_INT_COUNT_THRESHOLD))
+ ticks = ICC_SAFE_INT_TICKS;
+
+ spin_lock(&host->lock);
+ iowrite32((count << 24 | ticks), hcr_base + ICC);
+
+ intr_coalescing_count = count;
+ intr_coalescing_ticks = ticks;
+ spin_unlock(&host->lock);
+
+ DPRINTK("intrrupt coalescing, count = 0x%x, ticks = %x\n",
+ intr_coalescing_count, intr_coalescing_ticks);
+ DPRINTK("ICC register status: (hcr base: 0x%x) = 0x%x\n",
+ hcr_base, ioread32(hcr_base + ICC));
+}
+
+static ssize_t fsl_sata_intr_coalescing_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return sprintf(buf, "%d %d\n",
+ intr_coalescing_count, intr_coalescing_ticks);
+}
+
+static ssize_t fsl_sata_intr_coalescing_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ unsigned int coalescing_count, coalescing_ticks;
+
+ if (sscanf(buf, "%d%d",
+ &coalescing_count,
+ &coalescing_ticks) != 2) {
+ printk(KERN_ERR "fsl-sata: wrong parameter format.\n");
+ return -EINVAL;
+ }
+
+ fsl_sata_set_irq_coalescing(dev_get_drvdata(dev),
+ coalescing_count, coalescing_ticks);
+
+ return strlen(buf);
+}
+
static void sata_fsl_dev_config(struct ata_device *dev)
{
dev->max_sectors = 16;
@@ -352,11 +428,11 @@ static unsigned int sata_fsl_fill_sg(struct ata_queued_cmd *qc, void *cmd_desc,
(unsigned long long)sg_addr, sg_len);
/* warn if each s/g element is not dword aligned */
- if (sg_addr & 0x03)
+ if (unlikely(sg_addr & 0x03))
ata_port_printk(qc->ap, KERN_ERR,
"s/g addr unaligned : 0x%llx\n",
(unsigned long long)sg_addr);
- if (sg_len & 0x03)
+ if (unlikely(sg_len & 0x03))
ata_port_printk(qc->ap, KERN_ERR,
"s/g len unaligned : 0x%x\n", sg_len);
@@ -1305,6 +1381,13 @@ static int sata_fsl_init_controller(struct ata_host *host)
iowrite32(0x00000FFFF, hcr_base + DE);
/*
+ * reset the number of command complete bits which will cause the
+ * interrupt to be signaled
+ */
+ fsl_sata_set_irq_coalescing(host, intr_coalescing_count,
+ intr_coalescing_ticks);
+
+ /*
* host controller will be brought on-line, during xx_port_start()
* callback, that should also initiate the OOB, COMINIT sequence
*/
@@ -1368,7 +1451,7 @@ static int sata_fsl_probe(struct platform_device *ofdev)
void __iomem *csr_base = NULL;
struct sata_fsl_host_priv *host_priv = NULL;
int irq;
- struct ata_host *host;
+ struct ata_host *host = NULL;
u32 temp;
struct ata_port_info pi = sata_fsl_port_info[0];
@@ -1430,6 +1513,10 @@ static int sata_fsl_probe(struct platform_device *ofdev)
/* allocate host structure */
host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_FSL_MAX_PORTS);
+ if (!host) {
+ retval = -ENOMEM;
+ goto error_exit_with_cleanup;
+ }
/* host->iomap is not used currently */
host->private_data = host_priv;
@@ -1447,10 +1534,24 @@ static int sata_fsl_probe(struct platform_device *ofdev)
dev_set_drvdata(&ofdev->dev, host);
+ host_priv->intr_coalescing.show = fsl_sata_intr_coalescing_show;
+ host_priv->intr_coalescing.store = fsl_sata_intr_coalescing_store;
+ sysfs_attr_init(&host_priv->intr_coalescing.attr);
+ host_priv->intr_coalescing.attr.name = "intr_coalescing";
+ host_priv->intr_coalescing.attr.mode = S_IRUGO | S_IWUSR;
+ retval = device_create_file(host->dev, &host_priv->intr_coalescing);
+ if (retval)
+ goto error_exit_with_cleanup;
+
return 0;
error_exit_with_cleanup:
+ if (host) {
+ dev_set_drvdata(&ofdev->dev, NULL);
+ ata_host_detach(host);
+ }
+
if (hcr_base)
iounmap(hcr_base);
if (host_priv)
@@ -1464,6 +1565,8 @@ static int sata_fsl_remove(struct platform_device *ofdev)
struct ata_host *host = dev_get_drvdata(&ofdev->dev);
struct sata_fsl_host_priv *host_priv = host->private_data;
+ device_remove_file(&ofdev->dev, &host_priv->intr_coalescing);
+
ata_host_detach(host);
dev_set_drvdata(&ofdev->dev, NULL);
--
1.7.5.1
^ permalink raw reply related
* [PATCH 2/2] powerpc: Abstract common define of signal multiplex control for qe
From: Zhicheng Fan @ 2012-01-20 5:00 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Fanzc
In-Reply-To: <1327035611-22794-1-git-send-email-B32736@freescale.com>
From: Fanzc <b32736@freeescale.com>
The mpc85xx_rdb and mpc85xx_mds have commom define of signal multiplex for qe ,so
they need to go in common header, the patch abstract them to fsl_guts.h
Signed-off-by: Fanzc <b32736@freeescale.com>
---
arch/powerpc/include/asm/fsl_guts.h | 19 +++++++++++++++++++
arch/powerpc/platforms/85xx/mpc85xx_mds.c | 7 ++-----
2 files changed, 21 insertions(+), 5 deletions(-)
diff --git a/arch/powerpc/include/asm/fsl_guts.h b/arch/powerpc/include/asm/fsl_guts.h
index bebd124..efacfe3 100644
--- a/arch/powerpc/include/asm/fsl_guts.h
+++ b/arch/powerpc/include/asm/fsl_guts.h
@@ -114,6 +114,25 @@ struct ccsr_guts_86xx {
__be32 srds2cr1; /* 0x.0f44 - SerDes2 Control Register 0 */
} __attribute__ ((packed));
+#ifdef CONFIG_PPC_85xx
+
+/* Alternate function signal multiplex control */
+#define MPC85xx_PMUXCR_OFFSET 0x60
+#define MPC85xx_PMUXCR_QE0 0x00008000
+#define MPC85xx_PMUXCR_QE2 0x00002000
+#define MPC85xx_PMUXCR_QE3 0x00001000
+#define MPC85xx_PMUXCR_QE4 0x00000800
+#define MPC85xx_PMUXCR_QE5 0x00000400
+#define MPC85xx_PMUXCR_QE6 0x00000200
+#define MPC85xx_PMUXCR_QE7 0x00000100
+#define MPC85xx_PMUXCR_QE8 0x00000080
+#define MPC85xx_PMUXCR_QE9 0x00000040
+#define MPC85xx_PMUXCR_QE10 0x00000020
+#define MPC85xx_PMUXCR_QE11 0x00000010
+#define MPC85xx_PMUXCR_QE12 0x00000008
+
+#endif
+
#ifdef CONFIG_PPC_86xx
#define CCSR_GUTS_DMACR_DEV_SSI 0 /* DMA controller/channel set to SSI */
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 1d15a0c..1bd339a 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -51,6 +51,7 @@
#include <asm/qe_ic.h>
#include <asm/mpic.h>
#include <asm/swiotlb.h>
+#include <asm/fsl_guts.h>
#include "smp.h"
#include "mpc85xx.h"
@@ -268,11 +269,7 @@ static void __init mpc85xx_mds_qe_init(void)
mpc85xx_mds_reset_ucc_phys();
if (machine_is(p1021_mds)) {
-#define MPC85xx_PMUXCR_OFFSET 0x60
-#define MPC85xx_PMUXCR_QE0 0x00008000
-#define MPC85xx_PMUXCR_QE3 0x00001000
-#define MPC85xx_PMUXCR_QE9 0x00000040
-#define MPC85xx_PMUXCR_QE12 0x00000008
+
static __be32 __iomem *pmuxcr;
np = of_find_node_by_name(NULL, "global-utilities");
--
1.7.0.4
^ permalink raw reply related
* [PATCH 1/2] P1025RDB: add Quicc Engine support
From: Zhicheng Fan @ 2012-01-20 5:00 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Fanzc
From: Fanzc <b32736@freeescale.com>
Signed-off-by: Fanzc <b32736@freeescale.com>
---
arch/powerpc/platforms/85xx/mpc85xx_rdb.c | 79 ++++++++++++++++++++++++++++-
1 files changed, 78 insertions(+), 1 deletions(-)
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
index 1950076..1ba67aa 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
@@ -26,6 +26,9 @@
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
+#include <asm/qe.h>
+#include <asm/qe_ic.h>
+#include <asm/fsl_guts.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
@@ -47,6 +50,10 @@ void __init mpc85xx_rdb_pic_init(void)
struct mpic *mpic;
unsigned long root = of_get_flat_dt_root();
+#ifdef CONFIG_QUICC_ENGINE
+ struct device_node *np;
+#endif
+
if (of_flat_dt_is_compatible(root, "fsl,MPC85XXRDB-CAMP")) {
mpic = mpic_alloc(NULL, 0,
MPIC_BIG_ENDIAN | MPIC_BROKEN_FRR_NIRQS |
@@ -62,6 +69,18 @@ void __init mpc85xx_rdb_pic_init(void)
BUG_ON(mpic == NULL);
mpic_init(mpic);
+
+#ifdef CONFIG_QUICC_ENGINE
+ np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
+ if (np) {
+ qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
+ qe_ic_cascade_high_mpic);
+ of_node_put(np);
+
+ } else
+ printk(KERN_ERR "Could not find qe-ic node\n");
+#endif
+
}
/*
@@ -69,7 +88,7 @@ void __init mpc85xx_rdb_pic_init(void)
*/
static void __init mpc85xx_rdb_setup_arch(void)
{
-#ifdef CONFIG_PCI
+#if defined(CONFIG_PCI) || defined(CONFIG_QUICC_ENGINE)
struct device_node *np;
#endif
@@ -85,6 +104,64 @@ static void __init mpc85xx_rdb_setup_arch(void)
#endif
mpc85xx_smp_init();
+
+#ifdef CONFIG_QUICC_ENGINE
+ np = of_find_compatible_node(NULL, NULL, "fsl,qe");
+ if (!np) {
+ printk(KERN_ERR "Could not find Quicc Engine node\n");
+ goto qe_fail;
+ }
+
+ qe_reset();
+ of_node_put(np);
+
+ np = of_find_node_by_name(NULL, "par_io");
+ if (np) {
+ struct device_node *ucc;
+
+ par_io_init(np);
+ of_node_put(np);
+
+ for_each_node_by_name(ucc, "ucc")
+ par_io_of_config(ucc);
+
+ }
+ if (machine_is(p1025_rdb)) {
+
+ __be32 __iomem *pmuxcr;
+
+ np = of_find_node_by_name(NULL, "global-utilities");
+
+ if (np) {
+ pmuxcr = of_iomap(np, 0) + MPC85xx_PMUXCR_OFFSET;
+
+ if (!pmuxcr)
+ pr_err(KERN_EMERG "Error: Alternate function"
+ " signal multiplex control register not"
+ " mapped!\n");
+ else {
+#if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
+ /* P1025 has pins muxed for QE and other functions. To
+ * enable QE UEC mode, we need to set bit QE0 for UCC1
+ * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
+ * and QE12 for QE MII management singals in PMUXCR
+ * register.
+ */
+ setbits32(pmuxcr, MPC85xx_PMUXCR_QE0 |
+ MPC85xx_PMUXCR_QE3 |
+ MPC85xx_PMUXCR_QE9 |
+ MPC85xx_PMUXCR_QE12);
+#endif
+ }
+
+ of_node_put(np);
+ }
+
+ }
+
+qe_fail:
+#endif /* CONFIG_QUICC_ENGINE */
+
printk(KERN_INFO "MPC85xx RDB board from Freescale Semiconductor\n");
}
--
1.7.0.4
^ permalink raw reply related
* linux-next: build failure after merge of the final tree
From: Stephen Rothwell @ 2012-01-20 7:21 UTC (permalink / raw)
To: Benjamin Herrenschmidt, Paul Mackerras, linuxppc-dev
Cc: Deepthi Dharwar, Arun R Bharadwaj, linux-next, linux-kernel,
Trinabh Gupta
[-- Attachment #1: Type: text/plain, Size: 750 bytes --]
Hi all,
After merging the final tree, today's linux-next build (powerpc
allmodconfig) failed like this:
arch/powerpc/platforms/pseries/processor_idle.c:35:6: error: redefinition of 'update_smt_snooze_delay'
arch/powerpc/include/asm/system.h:230:20: note: previous definition of 'update_smt_snooze_delay' was here
arch/powerpc/platforms/pseries/processor_idle.c:175:5: error: redefinition of 'pseries_notify_cpuidle_add_cpu'
arch/powerpc/include/asm/system.h:231:19: note: previous definition of 'pseries_notify_cpuidle_add_cpu' was here
Caused by commit 707827f3387d ("powerpc/cpuidle: cpuidle driver for
pSeries"). For this build, CONFIG_PSERIES_IDLE is "m".
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
[-- Attachment #2: Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply
* Re: linux-next: build failure after merge of the final tree
From: Deepthi Dharwar @ 2012-01-20 9:08 UTC (permalink / raw)
To: Stephen Rothwell
Cc: Trinabh Gupta, Arun R Bharadwaj, linux-kernel, linux-next,
Paul Mackerras, linuxppc-dev
In-Reply-To: <20120120182117.01a6eb5d3cfb3f2bdfb32ae4@canb.auug.org.au>
On 01/20/2012 12:51 PM, Stephen Rothwell wrote:
> Hi all,
>
> After merging the final tree, today's linux-next build (powerpc
> allmodconfig) failed like this:
>
> arch/powerpc/platforms/pseries/processor_idle.c:35:6: error: redefinition of 'update_smt_snooze_delay'
> arch/powerpc/include/asm/system.h:230:20: note: previous definition of 'update_smt_snooze_delay' was here
> arch/powerpc/platforms/pseries/processor_idle.c:175:5: error: redefinition of 'pseries_notify_cpuidle_add_cpu'
> arch/powerpc/include/asm/system.h:231:19: note: previous definition of 'pseries_notify_cpuidle_add_cpu' was here
>
> Caused by commit 707827f3387d ("powerpc/cpuidle: cpuidle driver for
> pSeries"). For this build, CONFIG_PSERIES_IDLE is "m".
>
>
>
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
Hi Stephen,
We had a discussion on this particular problem on ppcdev list a few
days back and concluded that it is best not have pseries_idle
as a module.
http://old.nabble.com/-PATCH--cpuidle%3A-Default-y-for-pseries-to33118294.html#a33127587
The following patch disables pseries cpuidle driver to be loaded as a
module as there are build problems reported when one is trying to do so.
arch/powerpc/platforms/pseries/processor_idle.c:35:6: error:
redefinition of 'update_smt_snooze_delay'
arch/powerpc/include/asm/system.h:230:20: note:
previous definition of 'update_smt_snooze_delay' was here
arch/powerpc/platforms/pseries/processor_idle.c:175:5:
error: redefinition of 'pseries_notify_cpuidle_add_cpu'
arch/powerpc/include/asm/system.h:231:19: note:
previous definition of 'pseries_notify_cpuidle_add_cpu' was here
Since the above two functions
are used in core power architecture functions (store_smt_snooze_delay
at kernel/sysfs.c and smp_xics_setup_cpu at platforms/pseries/smp.c),
this requires some rework in these interactions. For now please
disable PSERIES_IDLE to be built as a module for now.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
---
arch/powerpc/platforms/pseries/Kconfig | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/powerpc/platforms/pseries/Kconfig
b/arch/powerpc/platforms/pseries/Kconfig
index ae7b6d4..31f22c1 100644
--- a/arch/powerpc/platforms/pseries/Kconfig
+++ b/arch/powerpc/platforms/pseries/Kconfig
@@ -122,7 +122,7 @@ config DTL
Say N if you are unsure.
config PSERIES_IDLE
- tristate "Cpuidle driver for pSeries platforms"
+ bool "Cpuidle driver for pSeries platforms"
depends on CPU_IDLE
depends on PPC_PSERIES
default y
Regards,
Deepthi
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox