[PATCH] x86-64 highres/dyntick support

[PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

I'm pleased to announce the first cut of the final x86_64
highres/dyntick support, which I did based on Chris Wright's patch set,
which is again based on Arjan van de Ven's initial work:

http://www.tglx.de/projects/hrtimers/2.6.21-git2-x86-64/patches-2.6.21-git2.patch.bz2

Broken out version:

http://www.tglx.de/projects/hrtimers/2.6.21-git2-x86-64/patches-2.6.21-git2.tar.bz2

It applies on top of 2.6.21-git2 and contains the following patches:

# Andi's x86_64 queue (already in -mm and pending mainline merges)
x86_64-2.6.21-git2.patch 

# Outstanding fixups to highres/dyntick core and i386 
# (-mm and mainline pending)
highres-dyntick-avoid-xtime-lock-contention.patch
acpi-keep-tsc-stable-when-lapic-timer-c2-ok-is-set.patch
clocksource-fix-resume-logic.patch
clockevents-fix-resume-logic.patch

# x86_64 dyntick support
x86-64-untangle-hpet-headers.patch
x86-64-drive-set-rtc-mss.patch
i386-move-pit-setup-to-i8253-h.patch
x86-64-remove-dead-code-tsc-c.patch
x86-64-convert-to-clockevents.patch
x86-64-prepare-idle-for-dyntick.patch
x86-64-enable-highres-dyntick.patch

The x86-64-convert-to-clockevents.patch is rather large, but there is no
way to do this incremental. The clockevents conversion has to be done in
one go. 

The x86-64 clockevents patch set overall summary is:

 22 files changed, 631 insertions(+), 1199 deletions(-)

due to sharing the code of PIT and HPET with i386.

I did not dare to tackle sharing apic.c yet, but there is definitely a
chance to get this done some day when I get bored and do a:
# mkdir arch/x86  :)

I'm going to post the x86_64 set for review to LKML once the outstanding
highres/dyntick fixups have hit mainline resp. -mm

To create a highres / dyntick enabled kernel for x86_64:
http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.21.tar.bz2
http://kernel.org/pub/linux/kernel/v2.6/snapshots/patch-2.6.21-git2.bz2
http://www.tglx.de/projects/hrtimers/2.6.21-git2-x86-64/patches-2.6.21-git2.patch.bz2


Comments, bugreports, patches are welcome as ususal

Thanks,

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Nicolas Mailhot]

Thomas Gleixner <tglx <at> linutronix.de> writes:

> 
> I'm pleased to announce the first cut of the final x86_64
> highres/dyntick support, which I did based on Chris Wright's patch set,
> which is again based on Arjan van de Ven's initial work:

Do you have a 2.6.21-mm1 patchset?

Regards,

-- 
Nicolas Mailhot

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Mon, 2007-05-07 at 09:16 +0000, Nicolas Mailhot wrote:
> Thomas Gleixner <tglx <at> linutronix.de> writes:
> 
> > 
> > I'm pleased to announce the first cut of the final x86_64
> > highres/dyntick support, which I did based on Chris Wright's patch set,
> > which is again based on Arjan van de Ven's initial work:
> 
> Do you have a 2.6.21-mm1 patchset?

Not yet, but it should be halfways easy to do one. Stay tuned.

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Nicolas Mailhot]

Le lundi 07 mai 2007 à 17:28 +0200, Thomas Gleixner a écrit :
> On Mon, 2007-05-07 at 09:16 +0000, Nicolas Mailhot wrote:
> > Thomas Gleixner <tglx <at> linutronix.de> writes:
> > 
> > > 
> > > I'm pleased to announce the first cut of the final x86_64
> > > highres/dyntick support, which I did based on Chris Wright's patch set,
> > > which is again based on Arjan van de Ven's initial work:
> > 
> > Do you have a 2.6.21-mm1 patchset?
> 
> Not yet, but it should be halfways easy to do one. Stay tuned.

Ok, tuning now

Thanks

-- 
Nicolas Mailhot

Re: [PATCH] x86-64 highres/dyntick support

[Chris Wright]

* Thomas Gleixner (tglx@linutronix.de) wrote:
> I'm pleased to announce the first cut of the final x86_64
> highres/dyntick support, which I did based on Chris Wright's patch set,
> which is again based on Arjan van de Ven's initial work:

Cool.  I had finished mine as well, just didn't get time to polish
and resubmit.  Going through to see where we differ and if there's
any bits of my set that yours needs.  

thanks,
-chris

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Mon, 2007-05-07 at 09:31 -0700, Chris Wright wrote:
> * Thomas Gleixner (tglx@linutronix.de) wrote:
> > I'm pleased to announce the first cut of the final x86_64
> > highres/dyntick support, which I did based on Chris Wright's patch set,
> > which is again based on Arjan van de Ven's initial work:
> 
> Cool.  I had finished mine as well, just didn't get time to polish
> and resubmit.

Hrmpf, you could have saved my weekend :)

>   Going through to see where we differ and if there's
> any bits of my set that yours needs.  

Yes please.

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Chris Wright]

* Thomas Gleixner (tglx@linutronix.de) wrote:
> On Mon, 2007-05-07 at 09:31 -0700, Chris Wright wrote:
> > * Thomas Gleixner (tglx@linutronix.de) wrote:
> > > I'm pleased to announce the first cut of the final x86_64
> > > highres/dyntick support, which I did based on Chris Wright's patch set,
> > > which is again based on Arjan van de Ven's initial work:
> > 
> > Cool.  I had finished mine as well, just didn't get time to polish
> > and resubmit.
> 
> Hrmpf, you could have saved my weekend :)

Yeah, timing was just off, sorry about that.  I'm sure it'll improve
the end result ;-)

thanks,
-chris

Re: [PATCH] x86-64 highres/dyntick support

[Chris Wright]

* Thomas Gleixner (tglx@linutronix.de) wrote:
> On Mon, 2007-05-07 at 09:31 -0700, Chris Wright wrote:
> >   Going through to see where we differ and if there's
> > any bits of my set that yours needs.  
> 
> Yes please.

OK, looks very similar all things considered.  One thing I didn't do
was fix lapic timer calibration (was hoping you'd do that part, and you
did ;-)  I've noticed that something has changed and I'm seeing irq0
handled on cpu3 (4 cpu system), where it used to be on cpu0 as expected.
In addition lapic timer is firing there, and I'm seeing a higher
interrupt load than I used to.  This is the same in your set and mine.
Following is small set of patches that were the more obvious bits.

thanks,
-chris

[PATCH 1/5] x86_64: tsc compile fix

[Chris Wright]

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
---
Just double checked, this is already picked up in -v2 patch.

 arch/x86_64/kernel/tsc.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- tglx.orig/arch/x86_64/kernel/tsc.c
+++ tglx/arch/x86_64/kernel/tsc.c
@@ -84,7 +84,7 @@ static struct notifier_block time_cpufre
 static int __init cpufreq_tsc(void)
 {
 	cpufreq_register_notifier(&time_cpufreq_notifier_block,
-				  CPUFREQ_TRANSITION_NOTIFIER))
+				  CPUFREQ_TRANSITION_NOTIFIER);
 	return 0;
 }
 

Re: [PATCH 1/5] x86_64: tsc compile fix

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:42 -0700, Chris Wright wrote:
> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
> ---
> Just double checked, this is already picked up in -v2 patch.
> 
>  arch/x86_64/kernel/tsc.c |    2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> --- tglx.orig/arch/x86_64/kernel/tsc.c
> +++ tglx/arch/x86_64/kernel/tsc.c
> @@ -84,7 +84,7 @@ static struct notifier_block time_cpufre
>  static int __init cpufreq_tsc(void)
>  {
>  	cpufreq_register_notifier(&time_cpufreq_notifier_block,
> -				  CPUFREQ_TRANSITION_NOTIFIER))
> +				  CPUFREQ_TRANSITION_NOTIFIER);
>  	return 0;
>  }

Yep, have this already in my -v2 set along with the i386 compile fix
from Venki.

	tglx

[PATCH 2/5] x86_64: __setup_APIC_LVTT whitespace fix

[Chris Wright]

Completely trivial one.

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
---
 arch/x86_64/kernel/apic.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- tglx.orig/arch/x86_64/kernel/apic.c
+++ tglx/arch/x86_64/kernel/apic.c
@@ -779,7 +779,7 @@ void __init init_apic_mappings(void)
 
 #define APIC_DIVISOR 16
 
-static void __setup_APIC_LVTT(unsigned int clocks, int oneshot,int  irqen)
+static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
 {
 	unsigned int lvtt_value, tmp_value;
 

Re: [PATCH 2/5] x86_64: __setup_APIC_LVTT whitespace fix

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:43 -0700, Chris Wright wrote:
> Completely trivial one.
> 
> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
> ---
>  arch/x86_64/kernel/apic.c |    2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> --- tglx.orig/arch/x86_64/kernel/apic.c
> +++ tglx/arch/x86_64/kernel/apic.c
> @@ -779,7 +779,7 @@ void __init init_apic_mappings(void)
>  
>  #define APIC_DIVISOR 16
>  
> -static void __setup_APIC_LVTT(unsigned int clocks, int oneshot,int  irqen)
> +static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
>  {
>  	unsigned int lvtt_value, tmp_value;
>  

Thanks,

	tglx

[PATCH 3/5] i386: hpet assumes boot cpu is 0

[Chris Wright]

I fixed this in x86_64.  Looks like the kind of thing that will break
voyager on i386.

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
---
 arch/i386/kernel/hpet.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- tglx.orig/arch/i386/kernel/hpet.c
+++ tglx/arch/i386/kernel/hpet.c
@@ -334,7 +334,7 @@ int __init hpet_enable(void)
 		 * Start hpet with the boot cpu mask and make it
 		 * global after the IO_APIC has been initialized.
 		 */
-		hpet_clockevent.cpumask =cpumask_of_cpu(0);
+		hpet_clockevent.cpumask = cpumask_of_cpu(smp_processor_id());
 		clockevents_register_device(&hpet_clockevent);
 		global_clock_event = &hpet_clockevent;
 		return 1;

Re: [PATCH 3/5] i386: hpet assumes boot cpu is 0

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:44 -0700, Chris Wright wrote:
> I fixed this in x86_64.  Looks like the kind of thing that will break
> voyager on i386.

voyager has hpet ? Anyway good point.

	tglx

[PATCH 4/5] i386: i8253 clockevent shutdown and unused using pit

[Chris Wright]

Disable by programming pit directly when performing CLOCK_EVT_MODE_UNUSED
or CLOCK_EVT_MODE_SHUTDOWN transitions.  (A variant) tested successfully
by Joachim Deguara on a Geode that exhibited BZ 8027 behaviour (with
bad bogomips).

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Joachim Deguara <joachim.deguara@amd.com>
---
 arch/i386/kernel/i8253.c |   25 ++++---------------------
 1 file changed, 4 insertions(+), 21 deletions(-)

--- tglx.orig/arch/i386/kernel/i8253.c
+++ tglx/arch/i386/kernel/i8253.c
@@ -29,24 +29,6 @@ EXPORT_SYMBOL(i8253_lock);
  */
 struct clock_event_device *global_clock_event;
 
-/* Status of the PIT interrupt */
-static int pit_irq_disabled;
-
-/*
- * Control pit interrupt enable / disable
- */
-static void pit_control_irq(int disable)
-{
-	if (pit_irq_disabled == disable)
-		return;
-
-	pit_irq_disabled = disable;
-	if (disable)
-		disable_irq(0);
-	else
-		enable_irq(0);
-}
-
 /*
  * Initialize the PIT timer.
  *
@@ -65,17 +47,18 @@ static void init_pit_timer(enum clock_ev
 		outb_p(0x34, PIT_MODE);
 		outb_p(LATCH & 0xff , PIT_CH0);	/* LSB */
 		outb(LATCH >> 8 , PIT_CH0);	/* MSB */
-		pit_control_irq(0);
 		break;
 
 	case CLOCK_EVT_MODE_SHUTDOWN:
 	case CLOCK_EVT_MODE_UNUSED:
-		pit_control_irq(1);
+		outb_p(0x30, PIT_MODE);
+		outb_p(0, PIT_CH0);	/* LSB */
+		outb_p(0, PIT_CH0);	/* MSB */
 		break;
+
 	case CLOCK_EVT_MODE_ONESHOT:
 		/* One shot setup */
 		outb_p(0x38, PIT_MODE);
-		pit_control_irq(0);
 		break;
 
 	case CLOCK_EVT_MODE_RESUME:

Re: [PATCH 4/5] i386: i8253 clockevent shutdown and unused using pit

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:46 -0700, Chris Wright wrote:
> Disable by programming pit directly when performing CLOCK_EVT_MODE_UNUSED
> or CLOCK_EVT_MODE_SHUTDOWN transitions.  (A variant) tested successfully
> by Joachim Deguara on a Geode that exhibited BZ 8027 behaviour (with
> bad bogomips).

Sigh, we had problems with that one on Ingo's Vaio-of-fun-emulator
laptop. That's why I did the irq disable.

Ingo, can you please retest ?

	tglx

[PATCH 5/5] x86_64: restore restore nohpet cmdline

[Chris Wright]

Lost when merged with i386.  Happy to drop, but I suspect Andi would
rather not break existing users (I noticed because it was part of my
testing).  If dropped, Documentation needs updating.

Signed-off-by: Chris Wright <chrisw@sous-sol.org>
---
 arch/i386/kernel/hpet.c |    8 ++++++++
 1 file changed, 8 insertions(+)

--- tglx.orig/arch/i386/kernel/hpet.c
+++ tglx/arch/i386/kernel/hpet.c
@@ -78,6 +78,14 @@ static int __init hpet_setup(char* str)
 	return 1;
 }
 __setup("hpet=", hpet_setup);
+#ifdef CONFIG_X86_64
+static int __init disable_hpet(char *str)
+{
+	boot_hpet_disable = 1;
+	return 1;
+}
+__setup("nohpet", disable_hpet);
+#endif
 
 static inline int is_hpet_capable(void)
 {

Re: [PATCH 5/5] x86_64: restore restore nohpet cmdline

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:47 -0700, Chris Wright wrote:
> Lost when merged with i386.  Happy to drop, but I suspect Andi would
> rather not break existing users (I noticed because it was part of my
> testing).  If dropped, Documentation needs updating.

Fair enough.

> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
> ---
>  arch/i386/kernel/hpet.c |    8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> --- tglx.orig/arch/i386/kernel/hpet.c
> +++ tglx/arch/i386/kernel/hpet.c
> @@ -78,6 +78,14 @@ static int __init hpet_setup(char* str)
>  	return 1;
>  }
>  __setup("hpet=", hpet_setup);
> +#ifdef CONFIG_X86_64
> +static int __init disable_hpet(char *str)
> +{
> +	boot_hpet_disable = 1;
> +	return 1;
> +}
> +__setup("nohpet", disable_hpet);
> +#endif
>  
>  static inline int is_hpet_capable(void)
>  {

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:39 -0700, Chris Wright wrote:

> OK, looks very similar all things considered.  One thing I didn't do
> was fix lapic timer calibration (was hoping you'd do that part, and you
> did ;-)  I've noticed that something has changed and I'm seeing irq0
> handled on cpu3 (4 cpu system), where it used to be on cpu0 as expected.

Strange, irq balancing ?

> In addition lapic timer is firing there, and I'm seeing a higher
> interrupt load than I used to.  This is the same in your set and mine.

Is irq0 _and_ the lapic timer firing ?

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Chris Wright]

* Thomas Gleixner (tglx@linutronix.de) wrote:
> On Tue, 2007-05-08 at 02:39 -0700, Chris Wright wrote:
> 
> > OK, looks very similar all things considered.  One thing I didn't do
> > was fix lapic timer calibration (was hoping you'd do that part, and you
> > did ;-)  I've noticed that something has changed and I'm seeing irq0
> > handled on cpu3 (4 cpu system), where it used to be on cpu0 as expected.
> 
> Strange, irq balancing ?

That's what I was wondering, although i have same setup for 32-bit
and it behaves as expected with cpu0 taking hpet or pit on irq0
and lapic timer picked up on the other 3 cpus.

> > In addition lapic timer is firing there, and I'm seeing a higher
> > interrupt load than I used to.  This is the same in your set and mine.
> 
> Is irq0 _and_ the lapic timer firing ?

Yes.

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Tue, 2007-05-08 at 02:51 -0700, Chris Wright wrote:
> That's what I was wondering, although i have same setup for 32-bit
> and it behaves as expected with cpu0 taking hpet or pit on irq0
> and lapic timer picked up on the other 3 cpus.
> 
> > > In addition lapic timer is firing there, and I'm seeing a higher
> > > interrupt load than I used to.  This is the same in your set and mine.
> > 
> > Is irq0 _and_ the lapic timer firing ?
> 
> Yes.

Hmm, that's even more strange. Can you please provide the output
of /proc/timer_list ?

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Chris Wright]

* Thomas Gleixner (tglx@linutronix.de) wrote:
> Hmm, that's even more strange. Can you please provide the output
> of /proc/timer_list ?

It's quite normal looking, and a printk in clockevents_set_mode looks normal too.

[chrisw@localhost ~]$ cat /proc/timer_list
Timer List Version: v0.3
HRTIMER_MAX_CLOCK_BASES: 2
now at 313565930359 nsecs

cpu: 0
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:
 #0: <ffff810150223e38>, hrtimer_wakeup, S:01
 # expires at 313700587872 nsecs [in 134657513 nsecs]
 #1: <ffff810150223e38>, it_real_fn, S:01
 # expires at 332024684987 nsecs [in 18458754628 nsecs]
 #2: <ffff810150223e38>, hrtimer_wakeup, S:01
 # expires at 337032779067 nsecs [in 23466848708 nsecs]
 #3: <ffff810150223e38>, hrtimer_wakeup, S:01
 # expires at 1851212334864 nsecs [in 1537646404505 nsecs]
 #4: <ffff810150223e38>, it_real_fn, S:01
 # expires at 3635317355388 nsecs [in 3321751425029 nsecs]
 #5: <ffff810150223e38>, it_real_fn, S:01
 # expires at 3635630194993 nsecs [in 3322064264634 nsecs]

cpu: 1
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:

cpu: 2
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:

cpu: 3
 clock 0:
  .index:      0
  .resolution: 4000250 nsecs
  .get_time:   ktime_get_real
active timers:
 clock 1:
  .index:      1
  .resolution: 4000250 nsecs
  .get_time:   ktime_get
active timers:
 #0: <ffff810150223e38>, it_real_fn, S:01
 # expires at 313558625026 nsecs [in -7305333 nsecs]
 #1: <ffff810150223e38>, hrtimer_wakeup, S:01
 # expires at 369334850252 nsecs [in 55768919893 nsecs]
 #2: <ffff810150223e38>, it_real_fn, S:01
 # expires at 3936979059363 nsecs [in 3623413129004 nsecs]


Tick Device: mode:     0
Clock Event Device: hpet
 max_delta_ns:   85899346200
 min_delta_ns:   1920
 mult:           107374182
 shift:          32
 mode:           2
 next_event:     9223372036854775807 nsecs
 set_next_event: hpet_next_event
 set_mode:       hpet_set_mode
 event_handler:  tick_handle_periodic_broadcast
tick_broadcast_mask: 00000001


Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   671088687
 min_delta_ns:   1200
 mult:           53687081
 shift:          32
 mode:           1
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic

Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   671088687
 min_delta_ns:   1200
 mult:           53687081
 shift:          32
 mode:           2
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic

Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   671088687
 min_delta_ns:   1200
 mult:           53687081
 shift:          32
 mode:           2
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic

Tick Device: mode:     0
Clock Event Device: lapic
 max_delta_ns:   671088687
 min_delta_ns:   1200
 mult:           53687081
 shift:          32
 mode:           2
 next_event:     0 nsecs
 set_next_event: lapic_next_event
 set_mode:       lapic_timer_setup
 event_handler:  tick_handle_periodic


[chrisw@localhost ~]$ grep -e 0: -e LOC: /proc/interrupts 
  0:         72          2         58      36008   IO-APIC-edge      timer
LOC:      36655      36772      36725      36683 
[chrisw@localhost ~]$ grep -e 0: -e LOC: /proc/interrupts 
  0:         72          2         58      36165   IO-APIC-edge      timer
LOC:      36812      36929      36882      36840 
[chrisw@localhost ~]$ grep -e 0: -e LOC: /proc/interrupts 
  0:         72          2         58      36297   IO-APIC-edge      timer
LOC:      36944      37061      37014      36972 
[chrisw@localhost ~]$ grep -e 0: -e LOC: /proc/interrupts 
  0:         72          2         58      36424   IO-APIC-edge      timer
LOC:      37071      37188      37141      37099 

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Tue, 2007-05-08 at 03:06 -0700, Chris Wright wrote:

> Tick Device: mode:     0
> Clock Event Device: hpet
>  max_delta_ns:   85899346200
>  min_delta_ns:   1920
>  mult:           107374182
>  shift:          32
>  mode:           2
>  next_event:     9223372036854775807 nsecs
>  set_next_event: hpet_next_event
>  set_mode:       hpet_set_mode
>  event_handler:  tick_handle_periodic_broadcast
> tick_broadcast_mask: 00000001

Broadcasting is active. The system has C2 state, right ?

If it's not AMD you can add lapic_timer_c2_ok to the commandline.

	tglx

RE: [PATCH] x86-64 highres/dyntick support

[Pallipadi, Venkatesh]

 

>-----Original Message-----
>From: Chris Wright [mailto:chrisw@sous-sol.org] 
>Sent: Tuesday, May 08, 2007 2:52 AM
>To: Thomas Gleixner
>Cc: Chris Wright; LKML; Pallipadi, Venkatesh; john stultz; 
>Ingo Molnar; Arjan van de Ven; Steven Rostedt; Andi Kleen; 
>Andrew Morton
>Subject: Re: [PATCH] x86-64 highres/dyntick support
>
>* Thomas Gleixner (tglx@linutronix.de) wrote:
>> On Tue, 2007-05-08 at 02:39 -0700, Chris Wright wrote:
>> 
>> > OK, looks very similar all things considered.  One thing I 
>didn't do
>> > was fix lapic timer calibration (was hoping you'd do that 
>part, and you
>> > did ;-)  I've noticed that something has changed and I'm 
>seeing irq0
>> > handled on cpu3 (4 cpu system), where it used to be on 
>cpu0 as expected.
>> 
>> Strange, irq balancing ?
>
>That's what I was wondering, although i have same setup for 32-bit
>and it behaves as expected with cpu0 taking hpet or pit on irq0
>and lapic timer picked up on the other 3 cpus.
>

Yes. Looks like irq balancing issue. On i386 I see irq has flag
IRQF_NOBALANCING, but x86-64 does not have this flag. Can you add that
and check whether that makes any difference.

Thanks,
Venki

Re: [PATCH] x86-64 highres/dyntick support

[Venki Pallipadi]

Needs this minor fix to build on i386.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>

Index: linux-2.6.21-tolkml/include/asm-i386/hpet.h
===================================================================
--- linux-2.6.21-tolkml.orig/include/asm-i386/hpet.h	2007-05-07 14:32:37.000000000 -0700
+++ linux-2.6.21-tolkml/include/asm-i386/hpet.h	2007-05-07 14:43:54.000000000 -0700
@@ -71,17 +71,6 @@
 #ifdef CONFIG_X86_64
 /* hpet_readl/writel defines */
 #include <asm/vsyscall.h>
-
-#else
-static inline unsigned long hpet_readl(unsigned long a)
-{
-	return readl(hpet_virt_address + a);
-}
-
-static inline void hpet_writel(unsigned long d, unsigned long a)
-{
-	writel(d, hpet_virt_address + a);
-}
 #endif
 
 #ifdef CONFIG_HPET_EMULATE_RTC
Index: linux-2.6.21-tolkml/arch/i386/kernel/hpet.c
===================================================================
--- linux-2.6.21-tolkml.orig/arch/i386/kernel/hpet.c	2007-05-07 14:31:34.000000000 -0700
+++ linux-2.6.21-tolkml/arch/i386/kernel/hpet.c	2007-05-07 14:43:36.000000000 -0700
@@ -47,6 +47,16 @@
 
 static void __iomem * hpet_virt_address;
 
+static inline unsigned long hpet_readl(unsigned long a)
+{
+	return readl(hpet_virt_address + a);
+}
+
+static inline void hpet_writel(unsigned long d, unsigned long a)
+{
+	writel(d, hpet_virt_address + a);
+}
+
 static inline void hpet_set_mapping(void)
 {
 	hpet_virt_address = ioremap_nocache(hpet_address, HPET_MMAP_SIZE);

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

On Mon, 2007-05-07 at 15:43 -0700, Venki Pallipadi wrote:
> Needs this minor fix to build on i386.

Ouch. 

Should have compiled i386 myself once more. There is another fixlet
missing in x86_64, which was caused by my inability to cope with the
intellegence of quilt.

Updated patches uploaded to:

http://www.tglx.de/projects/hrtimers/2.6.21-git2-x86-64/

	tglx

Re: [PATCH] x86-64 highres/dyntick support

[Alistair John Strachan]

On Sunday 06 May 2007 21:58:47 Thomas Gleixner wrote:
> I'm pleased to announce the first cut of the final x86_64
> highres/dyntick support, which I did based on Chris Wright's patch set,
> which is again based on Arjan van de Ven's initial work:

I've noticed a few problems with this patch series, which I manually (without 
difficulty) ported to 2.6.22-rc1.

Firstly, the output of /proc/interrupts looks a bit strange. NO_HZ isn't 
enabled, just high resolution timers. HZ was set to 1000.

alistair@damocles:~$ cat /proc/interrupts
           CPU0       CPU1
  0:        195          0   IO-APIC-edge      timer
  1:         21      13698   IO-APIC-edge      i8042
  8:          0          0   IO-APIC-edge      rtc
  9:          0          0   IO-APIC-fasteoi   acpi
 14:        117      51178   IO-APIC-edge      libata
 15:          0          0   IO-APIC-edge      libata
 18:        455     449373   IO-APIC-fasteoi   lan-sky, EMU10K1
 19:          0          3   IO-APIC-fasteoi   yenta, ohci1394
 20:        220      86188   IO-APIC-fasteoi   ohci_hcd:usb2
 21:          0         26   IO-APIC-fasteoi   ehci_hcd:usb1
 22:          0        273   IO-APIC-fasteoi   sata_nv
 23:        928     507781   IO-APIC-fasteoi   sata_nv, lan
NMI:          0          0
LOC:    4723272    4797930
ERR:          0

Only 195 timer interrupts? I only see this on an AMD Opteron, it doesn't occur 
on an Intel Core 2 Duo. Mainline reports this counter regularly increasing 
with or without the acpi_pm clocksource loaded.

Secondly, /proc/cpuinfo seems to be broken:

alistair@damocles:~$ cat /proc/cpuinfo | grep MHz
cpu MHz         : 210779.550
cpu MHz         : 210779.550

Unless my CPU is just under 80 times faster than it used to be, these numbers 
are incorrect. I expect 2700.50, or something similar. cpufreq isn't compiled 
in.

Finally, and possibly related, the dmesg timestamps seem to be totally broken. 
Apparently my machine booted in less than 1 second, with the last messages 
as:

[    0.607862] bridge: topology change detected, propagating
[    0.607862] bridge: port 2(lan-sky) entering forwarding state
[    0.830472] Linux agpgart interface v0.102 (c) Dave Jones

Of course, all of these problems might be PEBKAC, but I'm sceptical.

Find the kernel config, updated patch (for 2.6.22-rc1), dmesg, contents 
of /proc/interrupts and /proc/cpuinfo here:

http://devzero.co.uk/~alistair/2.6.22-rc1-hrt/

-- 
Cheers,
Alistair.

Final year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.

Re: [PATCH] x86-64 highres/dyntick support

[Thomas Gleixner]

Alistair,

On Mon, 2007-05-14 at 02:17 +0100, Alistair John Strachan wrote:
> I've noticed a few problems with this patch series, which I manually (without 
> difficulty) ported to 2.6.22-rc1.

There are a couple of fixups pending. I'm going to push out a new queue
today.

> Only 195 timer interrupts? I only see this on an AMD Opteron, it doesn't occur 
> on an Intel Core 2 Duo. Mainline reports this counter regularly increasing 
> with or without the acpi_pm clocksource loaded.

We stop the PIT when we switch to the local APICs. On your Intel box you
might have deeper C-states which switch the system back to broadcast
mode via PIT.

> Secondly, /proc/cpuinfo seems to be broken:
> 
> alistair@damocles:~$ cat /proc/cpuinfo | grep MHz
> cpu MHz         : 210779.550
> cpu MHz         : 210779.550
> 
> Unless my CPU is just under 80 times faster than it used to be, these numbers 
> are incorrect. I expect 2700.50, or something similar. cpufreq isn't compiled 
> in.

Hmm. It seems the new TSC calibration routine is hosed.

> Finally, and possibly related, the dmesg timestamps seem to be totally broken. 
> Apparently my machine booted in less than 1 second, with the last messages 
> as:
> 
> [    0.607862] bridge: topology change detected, propagating
> [    0.607862] bridge: port 2(lan-sky) entering forwarding state
> [    0.830472] Linux agpgart interface v0.102 (c) Dave Jones

Hey, you have a really fast box :)

	tglx

[PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Thomas Gleixner]

I'm pleased to announce an updated version of the x86_64 highres/dyntick
support patches against 2.6.22-rc1:

To build a highres / dyntick enabled kernel for x86_64:

http://www.kernel.org/pub/linux/kernel/v2.6/linux-2.6.21.tar.bz2
http://www.kernel.org/pub/linux/kernel/v2.6/testing/patch-2.6.22-rc1.bz2
http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v1.patch

Broken out version is available here:
http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v1.patches.tar.bz2

Changes since the last version:

- Various fixups from Chris Wright
- TSC calibration fix (pointed out by Alistair John Strachan)

Comments, bugreports, patches are welcome as ususal

Thanks,

        tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Valdis.Kletnieks]

[-- Attachment #1: Type: text/plain, Size: 364 bytes --]

On Mon, 14 May 2007 12:26:08 +0200, Thomas Gleixner said:

> Broken out version is available here:
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v1.patches.tar.bz2

How unhappy am I likely to be if I try to apply this to a 21-mm2 kernel? It
doesn't *look* like any of the patches are in -mm2 (at least not under the
same name).

[-- Attachment #2: Type: application/pgp-signature, Size: 226 bytes --]

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Thomas Gleixner]

On Mon, 2007-05-14 at 16:10 -0400, Valdis.Kletnieks@vt.edu wrote:
> On Mon, 14 May 2007 12:26:08 +0200, Thomas Gleixner said:
> 
> > Broken out version is available here:
> > http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v1.patches.tar.bz2
> 
> How unhappy am I likely to be if I try to apply this to a 21-mm2 kernel? It
> doesn't *look* like any of the patches are in -mm2 (at least not under the
> same name).

There are probably some conflicts, but the wreckage should be not that
big.

	tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Alistair John Strachan]

On Monday 14 May 2007 11:26:08 Thomas Gleixner wrote:
> I'm pleased to announce an updated version of the x86_64 highres/dyntick
> support patches against 2.6.22-rc1:
[snip]
> - Various fixups from Chris Wright
> - TSC calibration fix (pointed out by Alistair John Strachan)
>
> Comments, bugreports, patches are welcome as ususal

Neither of the bugs I reported appear to be fixed.

I took a clean git tree from the 2.6.22-rc1 tag and patched with this version; 
my CPU MHz and dmesg counter still appear to be broken (v3 was used).

-- 
Cheers,
Alistair.

Final year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Thomas Gleixner]

On Mon, 2007-05-14 at 22:15 +0100, Alistair John Strachan wrote:
> On Monday 14 May 2007 11:26:08 Thomas Gleixner wrote:
> > I'm pleased to announce an updated version of the x86_64 highres/dyntick
> > support patches against 2.6.22-rc1:
> [snip]
> > - Various fixups from Chris Wright
> > - TSC calibration fix (pointed out by Alistair John Strachan)
> >
> > Comments, bugreports, patches are welcome as ususal
> 
> Neither of the bugs I reported appear to be fixed.
> 
> I took a clean git tree from the 2.6.22-rc1 tag and patched with this version; 
> my CPU MHz and dmesg counter still appear to be broken (v3 was used).

Sigh. /me feels stupid.

Can you please apply the following patch on top and check, whether it
fixes the problem ? Please provide the debug output, when it fails.

Thanks,

	tglx

Index: linux-2.6.21/arch/x86_64/kernel/tsc.c
===================================================================
--- linux-2.6.21.orig/arch/x86_64/kernel/tsc.c
+++ linux-2.6.21/arch/x86_64/kernel/tsc.c
@@ -135,7 +135,7 @@ static unsigned long __init tsc_read_ref
 	for (i = 0; i < MAX_RETRIES; i++) {
 		t1 = get_cycles_sync();
 		if (hpet)
-			*hpet = hpet_readl(HPET_COUNTER);
+			*hpet = hpet_readl(HPET_COUNTER) & 0xFFFFFFFF;
 		else
 			*pm = acpi_pm_read_early();
 		t2 = get_cycles_sync();
@@ -177,8 +177,10 @@ void __init tsc_calibrate(void)
 	tsc_khz = (tr2 - tr1) / 50;
 
 	/* hpet or pmtimer available ? */
-	if (!hpet && !pm1 && !pm2)
+	if (!hpet && !pm1 && !pm2) {
+		printk(KERN_INFO "TSC calibrated against tick interrupt\n");
 		return;
+	}
 
 	/* Check, whether the sampling was disturbed by an SMI */
 	if (tsc1 == ULONG_MAX || tsc2 == ULONG_MAX) {
@@ -190,14 +192,25 @@ void __init tsc_calibrate(void)
 	tsc2 = (tsc2 - tsc1) * 1000000000L;
 
 	if (hpet) {
-		hpet2 = (hpet2 - hpet1) & 0xFFFFFFFF;
+		printk(KERN_INFO "TSC calibrated against hpet %ld %ld",
+		       hpet1, hpet2);
+		if (hpet2 < hpet1)
+			hpet2 += 0x100000000;
+		hpet2 -= hpet1;
 		tsc1 = (hpet2 * hpet_readl(HPET_PERIOD)) / 1000;
+		printk(" %lu %lu\n", hpet2, tsc1);
 	} else {
-		pm2 = (pm2 -pm1) & ACPI_PM_MASK;
+		printk(KERN_INFO "TSC calibrated against pm_timer %ld %ld",
+		       pm1, pm2);
+		if (pm2 < pm1)
+			pm2 += ACPI_PM_OVRRUN;
+		pm2 -= pm1;
 		tsc1 = (pm2 * PMTMR_TICKS_PER_SEC) / 1000;
+		printk(" %lu %lu\n", pm2, tsc1);
 	}
 
 	tsc_khz = tsc2 / tsc1;
+	printk(KERN_INFO "tsckhz: %lu %lu %u\n", tsc2, tsc1, tsc_khz);
 }
 
 /*

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v1

[Alistair John Strachan]

On Monday 14 May 2007 23:05:14 Thomas Gleixner wrote:
> On Mon, 2007-05-14 at 22:15 +0100, Alistair John Strachan wrote:
> > On Monday 14 May 2007 11:26:08 Thomas Gleixner wrote:
> > > I'm pleased to announce an updated version of the x86_64
> > > highres/dyntick support patches against 2.6.22-rc1:
> >
> > [snip]
> >
> > > - Various fixups from Chris Wright
> > > - TSC calibration fix (pointed out by Alistair John Strachan)
> > >
> > > Comments, bugreports, patches are welcome as ususal
> >
> > Neither of the bugs I reported appear to be fixed.
> >
> > I took a clean git tree from the 2.6.22-rc1 tag and patched with this
> > version; my CPU MHz and dmesg counter still appear to be broken (v3 was
> > used).
>
> Sigh. /me feels stupid.
>
> Can you please apply the following patch on top and check, whether it
> fixes the problem ? Please provide the debug output, when it fails.

Doesn't fix the problem, and here is the debug:

TSC calibrated against pm_timer 8927439 9106459 179020 640810145
tsckhz: 135069550000000000 640810145 210779356
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 210779.356 MHz processor.

(Perhaps if this debug effort has to continue, we could remove some of these 
gentlemen from CC?)

-- 
Cheers,
Alistair.

Final year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.

[PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Thomas Gleixner]

I've uploaded a new version of the x86_64 highres/dyntick patches:

http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v4.patch

Broken out version:

http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v4.patches.tar.bz2

Changes since last version:

- TSC calibration against PM-Timer

	tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Thomas Gleixner wrote:
> I've uploaded a new version of the x86_64 highres/dyntick patches:
> 
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v4.patch

Hangs at boot here:
	Kernel alive
	Kernel direct mapping tables up to 100000000 @ 8000-d000
(and that's it)

This is a Dell Inspiron E1705 with a Core 2 Duo 2.16GHz

highres-v3 also hung at the same point, but 2.6.21-git2-v2 worked
2.6.22-rc1 boots without problem

Is there any information I can provide to help track down the problem?

Thanks,

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGSb5JaI0dwg4A47wRAjkgAJ9Urvpo+cTAbRvblYovBYy3PD76jACfbtjj
EZSrOZDFMnOYjc02nHSAxaM=
=/ffY
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Thomas Gleixner]

Frank,

On Tue, 2007-05-15 at 09:06 -0500, Frank Sorenson wrote:
> Hangs at boot here:
> 	Kernel alive
> 	Kernel direct mapping tables up to 100000000 @ 8000-d000
> (and that's it)
> 
> This is a Dell Inspiron E1705 with a Core 2 Duo 2.16GHz
> 
> highres-v3 also hung at the same point, but 2.6.21-git2-v2 worked
> 2.6.22-rc1 boots without problem

Can you please try the following three command line option addons ?

1: highres=off nohz=off
2: highres=off
3: nohz=off

Thanks,

	tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Thomas Gleixner wrote:
> Frank,
> 
> On Tue, 2007-05-15 at 09:06 -0500, Frank Sorenson wrote:
>> Hangs at boot here:
>> 	Kernel alive
>> 	Kernel direct mapping tables up to 100000000 @ 8000-d000
>> (and that's it)
>>
>> This is a Dell Inspiron E1705 with a Core 2 Duo 2.16GHz
>>
>> highres-v3 also hung at the same point, but 2.6.21-git2-v2 worked
>> 2.6.22-rc1 boots without problem
> 
> Can you please try the following three command line option addons ?
> 
> 1: highres=off nohz=off
> 2: highres=off
> 3: nohz=off
> 
> Thanks,
> 
> 	tglx

All 3 hang at the same point.

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGSkA6aI0dwg4A47wRAuQzAKDcmAMR2e2Ce/3ytR+39XxgG76XjwCfVtbj
vWlY59M1gHz2Z8dIJWRYqTk=
=algX
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Frank Sorenson wrote:
> Thomas Gleixner wrote:
>> Frank,
> 
>> On Tue, 2007-05-15 at 09:06 -0500, Frank Sorenson wrote:
>>> Hangs at boot here:
>>> 	Kernel alive
>>> 	Kernel direct mapping tables up to 100000000 @ 8000-d000
>>> (and that's it)
>>>
>>> This is a Dell Inspiron E1705 with a Core 2 Duo 2.16GHz
>>>
>>> highres-v3 also hung at the same point, but 2.6.21-git2-v2 worked
>>> 2.6.22-rc1 boots without problem
>> Can you please try the following three command line option addons ?
> 
>> 1: highres=off nohz=off
>> 2: highres=off
>> 3: nohz=off
> 
>> Thanks,
> 
>> 	tglx
> 
> All 3 hang at the same point.

I have tracked down the offending patch in the series to
x86-64-convert-to-clockevents.patch

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGSpB2aI0dwg4A47wRAglRAJ4mJgbJClPd0hkXKp+YHq7G5VxQvgCgkVkv
TtOjrSrjrwiHQPkNCqlq314=
=lu8g
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Thomas Gleixner]

On Wed, 2007-05-16 at 00:02 -0500, Frank Sorenson wrote:
> >>> highres-v3 also hung at the same point, but 2.6.21-git2-v2 worked
> >>> 2.6.22-rc1 boots without problem
> >> Can you please try the following three command line option addons ?
> > 
> >> 1: highres=off nohz=off
> >> 2: highres=off
> >> 3: nohz=off
> > 
> > All 3 hang at the same point.

Ok.

> I have tracked down the offending patch in the series to
> x86-64-convert-to-clockevents.patch

Not surprising. :)

I'm going to add some early_printks for the next version, so we can get
an idea where it gets stuck

	tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Thomas Gleixner]

Frank,

On Wed, 2007-05-16 at 08:20 +0200, Thomas Gleixner wrote:
> > I have tracked down the offending patch in the series to
> > x86-64-convert-to-clockevents.patch
> 
> Not surprising. :)
> 
> I'm going to add some early_printks for the next version, so we can get
> an idea where it gets stuck

I went through the relevant changes since the git2-v2 version and the
only thing, which could affect the early boot process is the patch
snippet below.

Can you apply this either to the git2-v2 version and check, if it fails
as well, or reverse apply it to rc1-v4 and check, if the problem goes
away ?

Thanks,

	tglx


diff -uprN --exclude-from=/home/tglx/bin/diffit.exclude linux-2.6.21-git-x86-64/arch/i386/kernel/i8253.c linux-2.6.21/arch/i386/kernel/i8253.c
--- linux-2.6.21-git-x86-64/arch/i386/kernel/i8253.c	2007-05-16 09:58:01.000000000 +0200
+++ linux-2.6.21/arch/i386/kernel/i8253.c	2007-05-16 09:10:34.000000000 +0200
@@ -29,24 +29,6 @@ EXPORT_SYMBOL(i8253_lock);
  */
 struct clock_event_device *global_clock_event;
 
-/* Status of the PIT interrupt */
-static int pit_irq_disabled;
-
-/*
- * Control pit interrupt enable / disable
- */
-static void pit_control_irq(int disable)
-{
-	if (pit_irq_disabled == disable)
-		return;
-
-	pit_irq_disabled = disable;
-	if (disable)
-		disable_irq(0);
-	else
-		enable_irq(0);
-}
-
 /*
  * Initialize the PIT timer.
  *
@@ -65,17 +47,18 @@ static void init_pit_timer(enum clock_ev
 		outb_p(0x34, PIT_MODE);
 		outb_p(LATCH & 0xff , PIT_CH0);	/* LSB */
 		outb(LATCH >> 8 , PIT_CH0);	/* MSB */
-		pit_control_irq(0);
 		break;
 
 	case CLOCK_EVT_MODE_SHUTDOWN:
 	case CLOCK_EVT_MODE_UNUSED:
-		pit_control_irq(1);
+		outb_p(0x30, PIT_MODE);
+		outb_p(0, PIT_CH0);	/* LSB */
+		outb_p(0, PIT_CH0);	/* MSB */
 		break;
+
 	case CLOCK_EVT_MODE_ONESHOT:
 		/* One shot setup */
 		outb_p(0x38, PIT_MODE);
-		pit_control_irq(0);
 		break;
 
 	case CLOCK_EVT_MODE_RESUME:
@@ -129,7 +112,7 @@ void __init setup_pit_timer(void)
 	 * Start pit with the boot cpu mask and make it global after the
 	 * IO_APIC has been initialized.
 	 */
-	pit_clockevent.cpumask = cpumask_of_cpu(0);
+	pit_clockevent.cpumask = cpumask_of_cpu(smp_processor_id());
 	pit_clockevent.mult = div_sc(CLOCK_TICK_RATE, NSEC_PER_SEC, 32);
 	pit_clockevent.max_delta_ns =
 		clockevent_delta2ns(0x7FFF, &pit_clockevent);

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Alistair John Strachan]

On Tuesday 15 May 2007 09:18:02 Thomas Gleixner wrote:
> I've uploaded a new version of the x86_64 highres/dyntick patches:
>
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-hig
>hres-v4.patch
>
> Broken out version:
>
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-hig
>hres-v4.patches.tar.bz2
>
> Changes since last version:
>
> - TSC calibration against PM-Timer

Working fine now, thanks a lot. Great latencies on usleep() now too, just what 
I was looking for.

(BTW, with HRT (but not NO_HZ), does the HZ value have any effect on usleep() 
(and friends) latencies?)

-- 
Cheers,
Alistair.

Final year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v4

[Thomas Gleixner]

On Wed, 2007-05-16 at 00:23 +0100, Alistair John Strachan wrote:
> > - TSC calibration against PM-Timer
> 
> Working fine now, thanks a lot. Great latencies on usleep() now too, just what 
> I was looking for.
> 
> (BTW, with HRT (but not NO_HZ), does the HZ value have any effect on usleep() 
> (and friends) latencies?)

Not directly.

	tglx

[PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Thomas Gleixner]

I'm pleased to announce an updated version of the x86_64 highres/dyntick
support patches against 2.6.22-rc1:

http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v5.patch

Broken out version is available here:
http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v5.patches.tar.bz2

Changes since the last version:

- Enforced enabling of HPET (Venki Pallipadi)
	Detects and enables HPET on Intel ICHx chipsets, when the BIOS
	hides it.

	Venki, great work, thanks !

- Another variant of PIT wreckage fixup
	Frank, does this one work for you ?

- Various fixlets (me)

Comments, bugreports, patches are welcome as usual

Thanks,

        tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Thomas Gleixner wrote:
> I'm pleased to announce an updated version of the x86_64 highres/dyntick
> support patches against 2.6.22-rc1:
> 
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v5.patch
> 
> Broken out version is available here:
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v5.patches.tar.bz2
> 
> Changes since the last version:
> 
> - Enforced enabling of HPET (Venki Pallipadi)
> 	Detects and enables HPET on Intel ICHx chipsets, when the BIOS
> 	hides it.
> 
> 	Venki, great work, thanks !
> 
> - Another variant of PIT wreckage fixup
> 	Frank, does this one work for you ?

Unfortunately, no.

After adding *lots* of early_printks, I see that it hangs in
hpet_is_known(hdp) called from hpet_alloc(&hd), so something in the hpet
code is still buggy.  Adding nohpet to the kernel command line allows it
to boot correctly.

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGS1/3aI0dwg4A47wRAuaIAKD1MG5x4cvWXGRCwkHEGBzhUHyJlQCfez+S
ODHcJ4FEJ4W4LB7NzW32X6Q=
=r1q5
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Frank Sorenson wrote:

> After adding *lots* of early_printks, I see that it hangs in
> hpet_is_known(hdp) called from hpet_alloc(&hd), so something in the hpet
> code is still buggy.  Adding nohpet to the kernel command line allows it
> to boot correctly.

Hrm.  Looks like it gets past the hpet_is_known  There's still something
in the hpet detection code, but I didn't get to the bottom of it yet.
I'll do some more debugging to track down where it's really hanging.
Sorry for the noise.

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGS9lFaI0dwg4A47wRApdSAJoDsFphRHZq/tu3d4nJaqMvt+tLGQCghf1L
OCuPEpCRr9tBSnBdVNiShRE=
=NDZn
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Frank Sorenson wrote:

> Hrm.  Looks like it gets past the hpet_is_known  There's still something
> in the hpet detection code, but I didn't get to the bottom of it yet.
> I'll do some more debugging to track down where it's really hanging.
> Sorry for the noise.

I've tracked down this hang to a kzalloc in the hpet code that never
returns.  But only when using SLUB.  Using SLAB, the highres/dyntick
patch boots without problem.

...adding Christoph to the CC list...

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGTKkLaI0dwg4A47wRArYeAJwLs4fJDfj8CuYmUpCaifou6DBsHgCg9nvP
ilEqTd1DdOD13LSl7xVeKls=
=RT2W
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Christoph Lameter]

On Thu, 17 May 2007, Frank Sorenson wrote:

> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
> 
> Frank Sorenson wrote:
> 
> > Hrm.  Looks like it gets past the hpet_is_known  There's still something
> > in the hpet detection code, but I didn't get to the bottom of it yet.
> > I'll do some more debugging to track down where it's really hanging.
> > Sorry for the noise.
> 
> I've tracked down this hang to a kzalloc in the hpet code that never
> returns.  But only when using SLUB.  Using SLAB, the highres/dyntick
> patch boots without problem.
> 
> ...adding Christoph to the CC list...

Please boot with slub_debug.

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Frank Sorenson]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Christoph Lameter wrote:
> On Thu, 17 May 2007, Frank Sorenson wrote:
>> Frank Sorenson wrote:
>>
>>> Hrm.  Looks like it gets past the hpet_is_known  There's still something
>>> in the hpet detection code, but I didn't get to the bottom of it yet.
>>> I'll do some more debugging to track down where it's really hanging.
>>> Sorry for the noise.
>> I've tracked down this hang to a kzalloc in the hpet code that never
>> returns.  But only when using SLUB.  Using SLAB, the highres/dyntick
>> patch boots without problem.
>>
>> ...adding Christoph to the CC list...
> 
> Please boot with slub_debug.

No debugging output at all.  Still hangs with only:
	Kernel alive
	Kernel direct mapping tables up to 100000000 @ 8000-d000

Frank
- --
Frank Sorenson - KD7TZK
Linux Systems Engineer, DSS Engineering, UBS AG
frank@tuxrocks.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (GNU/Linux)
Comment: Using GnuPG with Fedora - http://enigmail.mozdev.org

iD8DBQFGTSPMaI0dwg4A47wRAkiaAJ0X80qq/ASp6zDEDAibOebZ1awBLACgh0OM
mHK5zxK+rwSNoiDlVRv6p8g=
=vegA
-----END PGP SIGNATURE-----

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Christoph Lameter]

On Thu, 17 May 2007, Frank Sorenson wrote:

> >> I've tracked down this hang to a kzalloc in the hpet code that never
> >> returns.  But only when using SLUB.  Using SLAB, the highres/dyntick
> >> patch boots without problem.
> >>
> >> ...adding Christoph to the CC list...
> > 
> > Please boot with slub_debug.
> 
> No debugging output at all.  Still hangs with only:
> 	Kernel alive
> 	Kernel direct mapping tables up to 100000000 @ 8000-d000

Is there some way you can get a stack trace?

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v5

[Christoph Lameter]

On Thu, 17 May 2007, Frank Sorenson wrote:

> > Please boot with slub_debug.
> 
> No debugging output at all.  Still hangs with only:
> 	Kernel alive
> 	Kernel direct mapping tables up to 100000000 @ 8000-d000

Hmmmm..... No other output? Could it be that early console output is not 
available? Try earlyprintk=xx? Try another platform that has working early 
printk support (x86_64 seems broken to me)?

[PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v7

[Thomas Gleixner]

I'm pleased to announce an updated version of the x86_64 highres/dyntick
support patches against 2.6.22-rc1:

http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v7.patch

Broken out version is available here:
http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v7.patches.tar.bz2

Changes since the last version:

- suspend / resume fix
- pc speaker preliminary locking fix
- networking nohz problem workaround (Mikulas Patocka) 

Comments, bug reports, patches are welcome as usual

Thanks,

        tglx

Re: [PATCH] x86-64 highres/dyntick support 2.6.22-rc1-v7

[Valdis.Kletnieks]

[-- Attachment #1: Type: text/plain, Size: 5444 bytes --]

On Fri, 18 May 2007 00:09:53 +0200, Thomas Gleixner said:
> Broken out version is available here:
> http://www.tglx.de/projects/hrtimers/2.6.22-rc1/linux-2.6.22-rc1-x86_64-highres-v7.patches.tar.bz2

By the time I got there, you'd put the -v8 version out there.  It applied
to a 2.6.22-rc1-mm1 tree with only minor bashing (basically, the patches
clocksource-fix-mismerge.diff and clocksource-watchdog-resumed-lockless.patch
appear to already be in -rc1-mm1, and hpet-check-counter.diff in a ever-so
slightly different form).  I also threw on the 22-rc1 patch from linuxpowertop
to tweak some timeouts in the kernel...

Boots and runs on a Dell Latitude D820 laptop with an Intel Core2 T7200.
Intel's 'powertop' was reporting as low as 25 wakeups/sec in single-user
mode, even with CONFIG_HZ=1000.  This is looking like a good -mm candidate...

Some 'powertop' results (I'm not at all clear why it's reporting 3000+ wakeups/
sec on the non-NOHZ kernels with HZ=1000. I can see 1000, or 2000 because it's
a dual-core, but 3000?).  It doesn't look like NOHZ gains me a *lot* of extra
battery time, but a bit (I believe the wattages to be reasonably accurate, the
'hours left' to be a crock...).  

-rc1-mm1 with X desktop running:
Cn          Avg residency (5s)  Long term residency avg
C0 (cpu running)        (18.8%)
C1                0.0ms ( 0.0%)                   0.0ms
C2                0.3ms ( 2.6%)                   0.3ms
C3                0.5ms (78.6%)                   0.5ms

Wakeups-from-idle per second :  3183.2 
Power usage (ACPI estimate) :  27.4 W (2.7 hours left)

Top causes for wakeups:
  16.4% (62.4)       <interrupt> : nvidia 
  13.2% (50.0)       S06cpuspeed : queue_delayed_work_on (delayed_work_timer_ 
  12.6% (48.0)               esd : schedule_timeout (process_timeout) 
   8.4% (31.8)           gkrellm : schedule_timeout (process_timeout) 
   7.7% (29.2)       <interrupt> : uhci_hcd:usb4 
   6.6% (25.2)              Xorg : do_setitimer (it_real_fn) 
   6.6% (25.0)       <interrupt> : uhci_hcd:usb3, HDA Intel 
   5.3% (20.0)            gyachi : schedule_timeout (process_timeout) 
   3.3% (12.6)               e16 : schedule_timeout (process_timeout) 
   2.6% (10.0)     <kernel core> : ehci_work (ehci_watchdog) 

Suggestion: Enable the CONFIG_NO_HZ kernel configuration option.

-rc1-mm1-hrt8 with X desktop running:
Cn          Avg residency (5s)  Long term residency avg
C0 (cpu running)        ( 8.5%)
C1                0.0ms ( 0.0%)                   0.0ms
C2                0.8ms ( 8.3%)                   1.0ms
C3                1.5ms (83.2%)                   1.5ms

Wakeups-from-idle per second :  1290.0 
Power usage (ACPI estimate) :  26.8 W (2.7 hours left)

Top causes for wakeups:
  23.8% (62.0)       <interrupt> : nvidia 
  15.8% (41.2)       S06cpuspeed : queue_delayed_work_on (delayed_work_timer_ 
  14.6% (38.0)           gkrellm : schedule_timeout (process_timeout) 
   8.7% (22.6)              Xorg : do_setitimer (it_real_fn) 
   7.6% (19.8)            gyachi : schedule_timeout (process_timeout) 
   3.8% (10.0)     <kernel core> : ehci_work (ehci_watchdog) 
   3.4% ( 8.8)               e16 : schedule_timeout (process_timeout) 
   3.2% ( 8.4)       firefox-bin : futex_wait (hrtimer_wakeup) 
   3.1% ( 8.0)     <kernel core> : usb_hcd_poll_rh_status (rh_timer_func) 
   2.5% ( 6.6)             pcscd : schedule_timeout (process_timeout) 

-rc1-mm1 single-user:
C0 (cpu running)        (10.0%)
C1                0.0ms ( 0.0%)                   0.0ms
C2                0.5ms ( 0.0%)                   0.6ms
C3                0.6ms (90.0%)                   0.6ms

Wakeups-from-idle per second :  3003.0 
Power usage (ACPI estimate) :  24.5 W (3.1 hours left)

Top causes for wakeups:
  42.1% ( 8.0)     <kernel core> : usb_hcd_poll_rh_status (rh_timer_func) 
  26.3% ( 5.0)     <kernel core> : fbcon_add_cursor_timer (cursor_timer_handl 
  14.7% ( 2.8)     <kernel core> : queue_delayed_work_on (delayed_work_timer_
   6.3% ( 1.2)       <interrupt> : libata 
   5.3% ( 1.0)             kedac : schedule_timeout (process_timeout) 
   1.1% ( 0.2)              init : schedule_timeout (process_timeout) 
   1.1% ( 0.2)     <kernel core> : page_writeback_init (wb_timer_fn) 
   1.1% ( 0.2)           pdflush : blk_plug_device (blk_unplug_timeout) 
   1.1% ( 0.2)     <kernel core> : neigh_table_init_no_netlink (neigh_periodi
   1.1% ( 0.2)        rc.sysinit : start_this_handle (commit_timeout) 

Suggestion: Enable the CONFIG_NO_HZ kernel configuration option.

-rc1-mm1-hrt8 single-user:
Cn          Avg residency (5s)  Long term residency avg
C0 (cpu running)        ( 0.1%)
C1                0.0ms ( 0.0%)                   0.0ms
C2                1.9ms ( 0.2%)                   1.9ms
C3               58.6ms (99.7%)                  58.6ms

Wakeups-from-idle per second :  36.0 
Power usage (ACPI estimate) :  23.2 W (2.9 hours left)

Top causes for wakeups:
  48.2% ( 8.0)     <kernel core> : usb_hcd_poll_rh_status (rh_timer_func) 
  30.1% ( 5.0)     <kernel core> : fbcon_add_cursor_timer (cursor_timer_handl 
  12.0% ( 2.0)     <kernel core> : queue_delayed_work_on (delayed_work_timer_ 
   6.0% ( 1.0)             kedac : schedule_timeout (process_timeout) 
   1.2% ( 0.2)              init : schedule_timeout (process_timeout) 
   1.2% ( 0.2)     <kernel core> : neigh_table_init_no_netlink (neigh_periodi 
   1.2% ( 0.2)        rc.sysinit : start_this_handle (commit_timeout)

[-- Attachment #2: Type: application/pgp-signature, Size: 226 bytes --]