* 2.6.29.1 sdhci: irq 19: nobody cared
@ 2009-04-17 15:00 Alessandro Bono
2009-06-03 20:09 ` [Sdhci-devel] " Pierre Ossman
0 siblings, 1 reply; 2+ messages in thread
From: Alessandro Bono @ 2009-04-17 15:00 UTC (permalink / raw)
To: sdhci-devel, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 4159 bytes --]
Hi
This is a bug that occur from time to time on my (unsed) sdhci card
drive
this is with kernel 2.6.29.1 (not a regression, I had the same problem
with older kernel)
[ 2885.888003] irq 19: nobody cared (try booting with the "irqpoll"
option)
[ 2885.888014] Pid: 0, comm: swapper Not tainted 2.6.29.1 #1
[ 2885.888019] Call Trace:
[ 2885.888023] <IRQ> [<ffffffff802751cb>] __report_bad_irq+0x38/0x87
[ 2885.888045] [<ffffffff80275332>] note_interrupt+0x118/0x182
[ 2885.888053] [<ffffffff80275962>] handle_fasteoi_irq+0xa1/0xc5
[ 2885.888062] [<ffffffff8020de49>] do_IRQ+0x70/0xe7
[ 2885.888069] [<ffffffff8020bf53>] ret_from_intr+0x0/0xa
[ 2885.888073] <EOI> [<ffffffff8024f317>] ? notifier_call_chain
+0x33/0x5b
[ 2885.888136] [<ffffffffa002b7bb>] ? acpi_idle_enter_simple
+0x186/0x1f8 [processor]
[ 2885.888159] [<ffffffffa002b7b1>] ? acpi_idle_enter_simple
+0x17c/0x1f8 [processor]
[ 2885.888169] [<ffffffff80399fa6>] ? cpuidle_idle_call+0x8c/0xc6
[ 2885.888176] [<ffffffff8020a649>] ? cpu_idle+0x52/0x93
[ 2885.888184] [<ffffffff804133cd>] ? rest_init+0x61/0x63
[ 2885.888189] handlers:
[ 2885.888192] [<ffffffffa02b2b86>] (sdhci_irq+0x0/0x49a [sdhci])
[ 2885.888208] Disabling IRQ #19
as you can see there is a lot of interrupts on mmc0 but seems strange
because I don't use this drive at all
cat /proc/interrupts
CPU0 CPU1
0: 320163 361871 IO-APIC-edge timer
1: 997 1017 IO-APIC-edge i8042
7: 0 0 IO-APIC-edge parport0
9: 3427 205 IO-APIC-fasteoi acpi
12: 920 876 IO-APIC-edge i8042
14: 43038 224 IO-APIC-edge ata_piix
15: 0 0 IO-APIC-edge ata_piix
16: 34787 50 IO-APIC-fasteoi uhci_hcd:usb2, yenta
17: 742 735 IO-APIC-fasteoi uhci_hcd:usb4, yenta, HDA
Intel, HDA Intel
18: 2 2 IO-APIC-fasteoi ohci1394, ehci_hcd:usb1,
uhci_hcd:usb7
19: 5399854 147 IO-APIC-fasteoi
mmc0
20: 12 12 IO-APIC-fasteoi ehci_hcd:usb3,
uhci_hcd:usb5
22: 0 0 IO-APIC-fasteoi
uhci_hcd:usb6
28: 57246 12 PCI-MSI-edge
eth0
29: 26003 21615 PCI-MSI-edge
ahci
30: 922 722 PCI-MSI-edge
iwlagn
NMI: 0 0 Non-maskable
interrupts
LOC: 235843 241312 Local timer
interrupts
RES: 58369 76238 Rescheduling
interrupts
CAL: 67 65 Function call
interrupts
TLB: 3679 4198 TLB
shootdowns
TRM: 0 0 Thermal event
interrupts
THR: 0 0 Threshold APIC
interrupts
SPU: 0 0 Spurious
interrupts
ERR:
0
MIS: 0
from dmesg
[ 9.220049] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 9.220054] ricoh-mmc: Copyright(c) Philip Langdale
[ 9.258786] sdhci: Secure Digital Host Controller Interface driver
[ 9.258788] sdhci: Copyright(c) Pierre Ossman
[ 9.329406] ricoh-mmc: Ricoh MMC controller found at 0000:02:06.4
[1180:0843] (rev 10)
[ 9.329424] ricoh-mmc: Controller is now disabled.
[ 9.329463] sdhci-pci 0000:02:06.3: SDHCI controller found
[1180:0822] (rev 20)
[ 9.329480] sdhci-pci 0000:02:06.3: PCI INT D -> GSI 19 (level, low)
-> IRQ 19
[ 9.331556] Registered led device: mmc0::
[ 9.332608] mmc0: SDHCI controller on PCI [0000:02:06.3] using PIO
dmesg attached
tell me if you need other info
thanks
--
Cordiali Saluti
Alessandro Bono
[-- Attachment #2: dmesg-2.6.29.1 --]
[-- Type: text/plain, Size: 52541 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.29.1 (root@champagne) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu12) ) #1 SMP Fri Apr 3 09:23:25 CEST 2009
[ 0.000000] Command line: root=UUID=0a96113a-5259-480a-abac-a27a7f9ae544 ro quiet splash
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bffb0000 (usable)
[ 0.000000] BIOS-e820: 00000000bffb0000 - 00000000bffc5400 (reserved)
[ 0.000000] BIOS-e820: 00000000bffc5400 - 00000000bffe7fb8 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bffe7fb8 - 00000000c0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed9a000 (reserved)
[ 0.000000] BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000013c000000 (usable)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x13c000 max_arch_pfn = 0x100000000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] last_pfn = 0xbffb0 max_arch_pfn = 0x100000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000bffb0000
[ 0.000000] 0000000000 - 00bfe00000 page 2M
[ 0.000000] 00bfe00000 - 00bffb0000 page 4k
[ 0.000000] kernel direct mapping tables up to bffb0000 @ 8000-d000
[ 0.000000] last_map_addr: bffb0000 end: bffb0000
[ 0.000000] init_memory_mapping: 0000000100000000-000000013c000000
[ 0.000000] 0100000000 - 013c000000 page 2M
[ 0.000000] kernel direct mapping tables up to 13c000000 @ b000-11000
[ 0.000000] last_map_addr: 13c000000 end: 13c000000
[ 0.000000] RAMDISK: 379f8000 - 37fef16a
[ 0.000000] ACPI: RSDP 000F7D10, 0024 (r2 HP )
[ 0.000000] ACPI: XSDT BFFC81CC, 0084 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: FACP BFFC8084, 00F4 (r4 HP 30C5 3 HP 1)
[ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
[ 0.000000] ACPI: DSDT BFFC8544, 12EAD (r1 HP 8510x 10000 MSFT 3000001)
[ 0.000000] ACPI: FACS BFFE7D80, 0040
[ 0.000000] ACPI: SLIC BFFC8250, 0176 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: HPET BFFC83C8, 0038 (r1 HP 30C5 1 HP 1)
[ 0.000000] ACPI: APIC BFFC8400, 0068 (r1 HP 30C5 1 HP 1)
[ 0.000000] ACPI: MCFG BFFC8468, 003C (r1 HP 30C5 1 HP 1)
[ 0.000000] ACPI: TCPA BFFC84A4, 0032 (r2 HP 30C5 1 HP 1)
[ 0.000000] ACPI: ASF! BFFC84D8, 0069 (r16 HP CHIMAYU 1 HP 0)
[ 0.000000] ACPI: SSDT BFFDB3F1, 0328 (r1 HP HPQSAT 1 MSFT 3000001)
[ 0.000000] ACPI: SSDT BFFDB719, 017C (r1 HP HPQMRM 1 MSFT 3000001)
[ 0.000000] ACPI: SSDT BFFDC29D, 025F (r1 HP Cpu0Tst 3000 INTL 20060317)
[ 0.000000] ACPI: SSDT BFFDC4FC, 00A6 (r1 HP Cpu1Tst 3000 INTL 20060317)
[ 0.000000] ACPI: SSDT BFFDC5A2, 04D7 (r1 HP CpuPm 3000 INTL 20060317)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 013c000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 000067e94c] TEXT DATA BSS ==> [0000200000 - 000067e94c]
[ 0.000000] #3 [00379f8000 - 0037fef16a] RAMDISK ==> [00379f8000 - 0037fef16a]
[ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #5 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000]
[ 0.000000] #6 [000000b000 - 000000c000] PGTABLE ==> [000000b000 - 000000c000]
[ 0.000000] [ffffe20000000000-ffffe200045fffff] PMD -> [ffff880028200000-ffff88002c7fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x0013c000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000bffb0
[ 0.000000] 0: 0x00100000 -> 0x0013c000
[ 0.000000] On node 0 totalpages: 1032015
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1253 pages reserved
[ 0.000000] DMA zone: 2690 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 767976 pages, LIFO batch:31
[ 0.000000] Normal zone: 3360 pages used for memmap
[ 0.000000] Normal zone: 242400 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bffb0000 - 00000000bffc5000
[ 0.000000] PM: Registered nosave memory: 00000000bffc5000 - 00000000bffc6000
[ 0.000000] PM: Registered nosave memory: 00000000bffc6000 - 00000000bffe7000
[ 0.000000] PM: Registered nosave memory: 00000000bffe7000 - 00000000bffe8000
[ 0.000000] PM: Registered nosave memory: 00000000bffe8000 - 00000000c0000000
[ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fed9a000
[ 0.000000] PM: Registered nosave memory: 00000000fed9a000 - 00000000feda0000
[ 0.000000] PM: Registered nosave memory: 00000000feda0000 - 00000000fedc0000
[ 0.000000] PM: Registered nosave memory: 00000000fedc0000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb00000
[ 0.000000] PM: Registered nosave memory: 00000000ffb00000 - 00000000ffc00000
[ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 00000000fff00000
[ 0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
[ 0.000000] NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Allocating 49152 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1013066
[ 0.000000] Kernel command line: root=UUID=0a96113a-5259-480a-abac-a27a7f9ae544 ro quiet splash
[ 0.000000] Initializing CPU#0
[ 0.000000] Experimental hierarchical RCU implementation.
[ 0.000000] Experimental hierarchical RCU init done.
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2394.566 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.004000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.004000] allocated 52428800 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.004000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
[ 0.004000] software IO TLB at phys 0x20000000 - 0x24000000
[ 0.004000] Memory: 3921096k/5177344k available (2197k kernel code, 1049284k absent, 206020k reserved, 1346k data, 312k init)
[ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.004000] hpet clockevent registered
[ 0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4789.13 BogoMIPS (lpj=9578264)
[ 0.004000] Mount-cache hash table entries: 256
[ 0.004000] Initializing cgroup subsys ns
[ 0.004000] Initializing cgroup subsys cpuacct
[ 0.004000] Initializing cgroup subsys memory
[ 0.004000] Initializing cgroup subsys devices
[ 0.004000] Initializing cgroup subsys freezer
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 4096K
[ 0.004000] [ds] using Core 2/Atom configuration
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] CPU0: Thermal monitoring handled by SMI
[ 0.004000] using mwait in idle threads.
[ 0.004000] ACPI: Core revision 20081204
[ 0.024064] Setting APIC routing to flat
[ 0.024434] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.066317] CPU0: Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0b
[ 0.068001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 4787.95 BogoMIPS (lpj=9575919)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 4096K
[ 0.004000] [ds] using Core 2/Atom configuration
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.153294] CPU1: Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0b
[ 0.153314] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.156028] Brought up 2 CPUs
[ 0.156030] Total of 2 processors activated (9577.09 BogoMIPS).
[ 0.156077] CPU0 attaching sched-domain:
[ 0.156079] domain 0: span 0-1 level MC
[ 0.156081] groups: 0 1
[ 0.156085] CPU1 attaching sched-domain:
[ 0.156086] domain 0: span 0-1 level MC
[ 0.156088] groups: 1 0
[ 0.156152] net_namespace: 1792 bytes
[ 0.156152] NET: Registered protocol family 16
[ 0.156152] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.156152] ACPI: bus type pci registered
[ 0.156152] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.156152] PCI: Not using MMCONFIG.
[ 0.156152] PCI: Using configuration type 1 for base access
[ 0.156152] bio: create slab <bio-0> at 0
[ 0.160044] ACPI: EC: Look up EC in DSDT
[ 0.188019] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.212311] ACPI: Interpreter enabled
[ 0.212314] ACPI: (supports S0 S3 S4 S5)
[ 0.212328] ACPI: Using IOAPIC for interrupt routing
[ 0.212391] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.222774] PCI: MCFG area at f8000000 reserved in ACPI motherboard resources
[ 0.225062] PCI: Using MMCONFIG at f8000000 - fbffffff
[ 0.236440] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.236440] ACPI: EC: driver started in interrupt mode
[ 0.240091] ACPI: No dock devices found.
[ 0.240101] ACPI: PCI Root Bridge [C003] (0000:00)
[ 0.240125] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.240125] pci 0000:00:01.0: PME# disabled
[ 0.240125] pci 0000:00:03.0: reg 10 64bit mmio: [0xe4500000-0xe450000f]
[ 0.240149] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.240151] pci 0000:00:03.0: PME# disabled
[ 0.240178] pci 0000:00:03.2: reg 10 io port: [0x5000-0x5007]
[ 0.240182] pci 0000:00:03.2: reg 14 io port: [0x5008-0x500b]
[ 0.240187] pci 0000:00:03.2: reg 18 io port: [0x5010-0x5017]
[ 0.240191] pci 0000:00:03.2: reg 1c io port: [0x5018-0x501b]
[ 0.240195] pci 0000:00:03.2: reg 20 io port: [0x5020-0x502f]
[ 0.240239] pci 0000:00:03.3: reg 10 io port: [0x5030-0x5037]
[ 0.240244] pci 0000:00:03.3: reg 14 32bit mmio: [0xe4501000-0xe4501fff]
[ 0.240349] pci 0000:00:19.0: reg 10 32bit mmio: [0xe4520000-0xe453ffff]
[ 0.240357] pci 0000:00:19.0: reg 14 32bit mmio: [0xe4540000-0xe4540fff]
[ 0.240364] pci 0000:00:19.0: reg 18 io port: [0x5040-0x505f]
[ 0.240414] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.240418] pci 0000:00:19.0: PME# disabled
[ 0.240468] pci 0000:00:1a.0: reg 20 io port: [0x5060-0x507f]
[ 0.240530] pci 0000:00:1a.1: reg 20 io port: [0x5080-0x509f]
[ 0.240598] pci 0000:00:1a.7: reg 10 32bit mmio: [0xe4541000-0xe45413ff]
[ 0.240660] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.240664] pci 0000:00:1a.7: PME# disabled
[ 0.240716] pci 0000:00:1b.0: reg 10 64bit mmio: [0xe4544000-0xe4547fff]
[ 0.240775] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.240779] pci 0000:00:1b.0: PME# disabled
[ 0.240860] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.240864] pci 0000:00:1c.0: PME# disabled
[ 0.240948] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.240952] pci 0000:00:1c.1: PME# disabled
[ 0.241040] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.241044] pci 0000:00:1c.4: PME# disabled
[ 0.241104] pci 0000:00:1d.0: reg 20 io port: [0x50a0-0x50bf]
[ 0.241168] pci 0000:00:1d.1: reg 20 io port: [0x50c0-0x50df]
[ 0.241230] pci 0000:00:1d.2: reg 20 io port: [0x50e0-0x50ff]
[ 0.241298] pci 0000:00:1d.7: reg 10 32bit mmio: [0xe4548000-0xe45483ff]
[ 0.241359] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.241364] pci 0000:00:1d.7: PME# disabled
[ 0.241528] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.241532] pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH6 GPIO
[ 0.241536] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0500 (mask 007f)
[ 0.241543] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 02e8 (mask 0007)
[ 0.241593] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.241600] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.241608] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.241615] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.241622] pci 0000:00:1f.1: reg 20 io port: [0x5100-0x510f]
[ 0.241692] pci 0000:00:1f.2: reg 10 io port: [0x13f0-0x13f7]
[ 0.241699] pci 0000:00:1f.2: reg 14 io port: [0x15f4-0x15f7]
[ 0.241706] pci 0000:00:1f.2: reg 18 io port: [0x1370-0x1377]
[ 0.241713] pci 0000:00:1f.2: reg 1c io port: [0x1574-0x1577]
[ 0.241721] pci 0000:00:1f.2: reg 20 io port: [0x5140-0x515f]
[ 0.241728] pci 0000:00:1f.2: reg 24 32bit mmio: [0xe4549000-0xe45497ff]
[ 0.241769] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.241773] pci 0000:00:1f.2: PME# disabled
[ 0.241825] pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xdfffffff]
[ 0.241833] pci 0000:01:00.0: reg 14 io port: [0x4000-0x40ff]
[ 0.241839] pci 0000:01:00.0: reg 18 32bit mmio: [0xe4400000-0xe440ffff]
[ 0.241862] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.241890] pci 0000:01:00.0: supports D1 D2
[ 0.241932] pci 0000:01:00.1: reg 10 32bit mmio: [0xe4410000-0xe4413fff]
[ 0.241992] pci 0000:01:00.1: supports D1 D2
[ 0.242057] pci 0000:00:01.0: bridge io port: [0x4000-0x4fff]
[ 0.242060] pci 0000:00:01.0: bridge 32bit mmio: [0xe4400000-0xe44fffff]
[ 0.242063] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.242254] pci 0000:10:00.0: reg 10 64bit mmio: [0xe4000000-0xe4001fff]
[ 0.242381] pci 0000:10:00.0: PME# supported from D0 D3hot D3cold
[ 0.242394] pci 0000:10:00.0: PME# disabled
[ 0.242482] pci 0000:00:1c.1: bridge 32bit mmio: [0xe4000000-0xe40fffff]
[ 0.242544] pci 0000:00:1c.4: bridge io port: [0x2000-0x3fff]
[ 0.242549] pci 0000:00:1c.4: bridge 32bit mmio: [0xe0000000-0xe3ffffff]
[ 0.242606] pci 0000:02:06.0: reg 10 32bit mmio: [0xe4100000-0xe4100fff]
[ 0.242628] pci 0000:02:06.0: supports D1 D2
[ 0.242629] pci 0000:02:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.242634] pci 0000:02:06.0: PME# disabled
[ 0.242673] pci 0000:02:06.1: reg 10 32bit mmio: [0xe4101000-0xe4101fff]
[ 0.242697] pci 0000:02:06.1: supports D1 D2
[ 0.242698] pci 0000:02:06.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.242703] pci 0000:02:06.1: PME# disabled
[ 0.242742] pci 0000:02:06.2: reg 10 32bit mmio: [0xe4102000-0xe41027ff]
[ 0.242801] pci 0000:02:06.2: supports D1 D2
[ 0.242802] pci 0000:02:06.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.242807] pci 0000:02:06.2: PME# disabled
[ 0.242847] pci 0000:02:06.3: reg 10 32bit mmio: [0xe4103000-0xe41030ff]
[ 0.242904] pci 0000:02:06.3: supports D1 D2
[ 0.242906] pci 0000:02:06.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.242910] pci 0000:02:06.3: PME# disabled
[ 0.242951] pci 0000:02:06.4: reg 10 32bit mmio: [0xe4104000-0xe41040ff]
[ 0.243010] pci 0000:02:06.4: supports D1 D2
[ 0.243011] pci 0000:02:06.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.243016] pci 0000:02:06.4: PME# disabled
[ 0.243070] pci 0000:00:1e.0: transparent bridge
[ 0.243077] pci 0000:00:1e.0: bridge 32bit mmio: [0xe4100000-0xe43fffff]
[ 0.243146] pci_bus 0000:00: on NUMA node 0
[ 0.243151] ACPI: PCI Interrupt Routing Table [\_SB_.C003._PRT]
[ 0.243412] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C096._PRT]
[ 0.243482] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C0B0._PRT]
[ 0.243591] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C11D._PRT]
[ 0.243672] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C131._PRT]
[ 0.243755] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C134._PRT]
[ 0.298307] ACPI: PCI Interrupt Link [C12D] (IRQs *10 11)
[ 0.298307] ACPI: PCI Interrupt Link [C12E] (IRQs *10 11)
[ 0.298307] ACPI: PCI Interrupt Link [C12F] (IRQs 10 *11)
[ 0.298307] ACPI: PCI Interrupt Link [C130] (IRQs 10 11) *5
[ 0.300020] ACPI: PCI Interrupt Link [C140] (IRQs *10 11)
[ 0.300259] ACPI: PCI Interrupt Link [C141] (IRQs 10 11) *5
[ 0.300497] ACPI: PCI Interrupt Link [C142] (IRQs 10 *11)
[ 0.300607] ACPI Exception (pci_link-0189): AE_NOT_FOUND, Evaluating _PRS [20081204]
[ 0.300728] ACPI: Power Resource [C238] (on)
[ 0.300728] ACPI: Power Resource [C254] (on)
[ 0.300728] ACPI: Power Resource [C17C] (off)
[ 0.300728] ACPI: Power Resource [C363] (off)
[ 0.300728] ACPI: Power Resource [C366] (off)
[ 0.300728] ACPI: Power Resource [C367] (off)
[ 0.300754] ACPI: Power Resource [C368] (off)
[ 0.300863] ACPI: Power Resource [C369] (off)
[ 0.300914] ACPI: Power Resource [C36A] (off)
[ 0.301023] ACPI: Power Resource [C383] (off)
[ 0.301132] ACPI: Power Resource [C384] (off)
[ 0.301240] ACPI: Power Resource [C385] (off)
[ 0.301349] ACPI: Power Resource [C386] (off)
[ 0.301458] ACPI: Power Resource [C387] (off)
[ 0.301469] PCI: Using ACPI for IRQ routing
[ 0.312014] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.312017] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.328004] pnp: PnP ACPI init
[ 0.328010] ACPI: bus type pnp registered
[ 0.338988] pnp: PnP ACPI: found 15 devices
[ 0.338990] ACPI: ACPI bus type pnp unregistered
[ 0.338997] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.338999] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.339001] system 00:00: iomem range 0x100000-0xbfffffff could not be reserved
[ 0.339008] system 00:0b: ioport range 0x500-0x55f has been reserved
[ 0.339010] system 00:0b: ioport range 0x800-0x80f has been reserved
[ 0.339013] system 00:0b: iomem range 0xffb00000-0xffbfffff has been reserved
[ 0.339015] system 00:0b: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.339019] system 00:0d: ioport range 0x4d0-0x4d1 has been reserved
[ 0.339021] system 00:0d: ioport range 0x1000-0x107f has been reserved
[ 0.339023] system 00:0d: ioport range 0x1100-0x113f has been reserved
[ 0.339025] system 00:0d: ioport range 0x1200-0x121f has been reserved
[ 0.339028] system 00:0d: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.339030] system 00:0d: iomem range 0xfec00000-0xfec000ff has been reserved
[ 0.339032] system 00:0d: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.339034] system 00:0d: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.339036] system 00:0d: iomem range 0xfed90000-0xfed99fff has been reserved
[ 0.339040] system 00:0e: iomem range 0xcf400-0xcffff has been reserved
[ 0.339042] system 00:0e: iomem range 0xfeda0000-0xfedbffff has been reserved
[ 0.339044] system 00:0e: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.343889] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.343891] pci 0000:00:01.0: IO window: 0x4000-0x4fff
[ 0.343895] pci 0000:00:01.0: MEM window: 0xe4400000-0xe44fffff
[ 0.343898] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.343902] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:08
[ 0.343903] pci 0000:00:1c.0: IO window: disabled
[ 0.343909] pci 0000:00:1c.0: MEM window: disabled
[ 0.343913] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.343920] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:10
[ 0.343921] pci 0000:00:1c.1: IO window: disabled
[ 0.343927] pci 0000:00:1c.1: MEM window: 0xe4000000-0xe40fffff
[ 0.343931] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.343938] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:28
[ 0.343941] pci 0000:00:1c.4: IO window: 0x2000-0x3fff
[ 0.343947] pci 0000:00:1c.4: MEM window: 0xe0000000-0xe3ffffff
[ 0.343951] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.343962] pci 0000:02:06.0: CardBus bridge, secondary bus 0000:03
[ 0.343963] pci 0000:02:06.0: IO window: 0x006000-0x0060ff
[ 0.343968] pci 0000:02:06.0: IO window: 0x006400-0x0064ff
[ 0.343972] pci 0000:02:06.0: PREFETCH window: 0xc4000000-0xc7ffffff
[ 0.343977] pci 0000:02:06.0: MEM window: 0xcc000000-0xcfffffff
[ 0.343981] pci 0000:02:06.1: CardBus bridge, secondary bus 0000:04
[ 0.343983] pci 0000:02:06.1: IO window: 0x006800-0x0068ff
[ 0.343987] pci 0000:02:06.1: IO window: 0x006c00-0x006cff
[ 0.343999] pci 0000:02:06.1: PREFETCH window: 0xc8000000-0xcbffffff
[ 0.344004] pci 0000:02:06.1: MEM window: 0xe8000000-0xebffffff
[ 0.344008] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.344011] pci 0000:00:1e.0: IO window: 0x6000-0x6fff
[ 0.344017] pci 0000:00:1e.0: MEM window: 0xe4100000-0xe43fffff
[ 0.344021] pci 0000:00:1e.0: PREFETCH window: 0x000000c4000000-0x000000cbffffff
[ 0.344034] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.344037] pci 0000:00:01.0: setting latency timer to 64
[ 0.344045] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.344049] pci 0000:00:1c.0: setting latency timer to 64
[ 0.344058] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.344062] pci 0000:00:1c.1: setting latency timer to 64
[ 0.344070] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.344074] pci 0000:00:1c.4: setting latency timer to 64
[ 0.344082] pci 0000:00:1e.0: setting latency timer to 64
[ 0.344090] pci 0000:02:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.344100] pci 0000:02:06.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.344105] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.344107] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.344109] pci_bus 0000:01: resource 0 io: [0x4000-0x4fff]
[ 0.344111] pci_bus 0000:01: resource 1 mem: [0xe4400000-0xe44fffff]
[ 0.344113] pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff]
[ 0.344114] pci_bus 0000:01: resource 3 mem: [0x0-0x0]
[ 0.344116] pci_bus 0000:08: resource 0 mem: [0x0-0x0]
[ 0.344118] pci_bus 0000:08: resource 1 mem: [0x0-0x0]
[ 0.344119] pci_bus 0000:08: resource 2 mem: [0x0-0x0]
[ 0.344120] pci_bus 0000:08: resource 3 mem: [0x0-0x0]
[ 0.344122] pci_bus 0000:10: resource 0 mem: [0x0-0x0]
[ 0.344124] pci_bus 0000:10: resource 1 mem: [0xe4000000-0xe40fffff]
[ 0.344125] pci_bus 0000:10: resource 2 mem: [0x0-0x0]
[ 0.344127] pci_bus 0000:10: resource 3 mem: [0x0-0x0]
[ 0.344128] pci_bus 0000:28: resource 0 io: [0x2000-0x3fff]
[ 0.344130] pci_bus 0000:28: resource 1 mem: [0xe0000000-0xe3ffffff]
[ 0.344132] pci_bus 0000:28: resource 2 mem: [0x0-0x0]
[ 0.344133] pci_bus 0000:28: resource 3 mem: [0x0-0x0]
[ 0.344135] pci_bus 0000:02: resource 0 io: [0x6000-0x6fff]
[ 0.344136] pci_bus 0000:02: resource 1 mem: [0xe4100000-0xe43fffff]
[ 0.344138] pci_bus 0000:02: resource 2 mem: [0xc4000000-0xcbffffff]
[ 0.344140] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.344141] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.344143] pci_bus 0000:03: resource 0 io: [0x6000-0x60ff]
[ 0.344145] pci_bus 0000:03: resource 1 io: [0x6400-0x64ff]
[ 0.344146] pci_bus 0000:03: resource 2 mem: [0xc4000000-0xc7ffffff]
[ 0.344148] pci_bus 0000:03: resource 3 mem: [0xcc000000-0xcfffffff]
[ 0.344150] pci_bus 0000:04: resource 0 io: [0x6800-0x68ff]
[ 0.344151] pci_bus 0000:04: resource 1 io: [0x6c00-0x6cff]
[ 0.344153] pci_bus 0000:04: resource 2 mem: [0xc8000000-0xcbffffff]
[ 0.344155] pci_bus 0000:04: resource 3 mem: [0xe8000000-0xebffffff]
[ 0.344176] NET: Registered protocol family 2
[ 0.380027] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.380498] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.382327] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.382860] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.382862] TCP reno registered
[ 0.392078] NET: Registered protocol family 1
[ 0.392185] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.503956] Switched to high resolution mode on CPU 0
[ 0.593610] it is
[ 0.808364] Freeing initrd memory: 6108k freed
[ 0.811728] audit: initializing netlink socket (disabled)
[ 0.811741] type=2000 audit(1239975323.809:1): initialized
[ 0.812116] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.814004] VFS: Disk quotas dquot_6.5.2
[ 0.814069] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.814144] msgmni has been set to 7672
[ 0.814293] alg: No test for stdrng (krng)
[ 0.814371] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.814373] io scheduler noop registered
[ 0.814422] io scheduler cfq registered (default)
[ 0.814573] pci 0000:01:00.0: Boot video device
[ 0.814678] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.814724] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.814829] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.814902] pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.815037] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 0.815111] pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
[ 0.815272] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.815346] pcieport-driver 0000:00:1c.4: irq 27 for MSI/MSI-X
[ 0.818273] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.818702] serial 0000:00:03.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.818772] 0000:00:03.3: ttyS0 at I/O 0x5030 (irq = 17) is a 16550A
[ 0.820036] brd: module loaded
[ 0.820117] PNP: PS/2 Controller [PNP0303:C251,PNP0f13:C252] at 0x60,0x64 irq 1,12
[ 0.821987] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.822745] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.822749] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.822752] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.822754] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.822756] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.822883] mice: PS/2 mouse device common for all mice
[ 0.822945] cpuidle: using governor ladder
[ 0.822947] cpuidle: using governor menu
[ 0.823192] TCP cubic registered
[ 0.823553] Freeing unused kernel memory: 312k freed
[ 0.823684] Write protecting the kernel read-only data: 3264k
[ 0.854052] input: AT Translated Set 2 keyboard as /class/input/input0
[ 0.929059] fuse init (API version 7.11)
[ 0.945851] fan PNP0C0B:00: registered as cooling_device0
[ 0.945857] ACPI: Fan [C36B] (off)
[ 0.946107] fan PNP0C0B:01: registered as cooling_device1
[ 0.946112] ACPI: Fan [C36C] (off)
[ 0.946358] fan PNP0C0B:02: registered as cooling_device2
[ 0.946363] ACPI: Fan [C36D] (off)
[ 0.946610] fan PNP0C0B:03: registered as cooling_device3
[ 0.946614] ACPI: Fan [C36E] (off)
[ 0.946859] fan PNP0C0B:04: registered as cooling_device4
[ 0.946864] ACPI: Fan [C36F] (off)
[ 0.946990] fan PNP0C0B:05: registered as cooling_device5
[ 0.946994] ACPI: Fan [C370] (off)
[ 0.947244] fan PNP0C0B:06: registered as cooling_device6
[ 0.947249] ACPI: Fan [C388] (off)
[ 0.947496] fan PNP0C0B:07: registered as cooling_device7
[ 0.947500] ACPI: Fan [C389] (off)
[ 0.947752] fan PNP0C0B:08: registered as cooling_device8
[ 0.947757] ACPI: Fan [C38A] (off)
[ 0.948011] fan PNP0C0B:09: registered as cooling_device9
[ 0.948015] ACPI: Fan [C38B] (off)
[ 0.948262] fan PNP0C0B:0a: registered as cooling_device10
[ 0.948267] ACPI: Fan [C38C] (off)
[ 0.952680] ACPI: SSDT BFFDB95D, 02C1 (r1 HP Cpu0Ist 3000 INTL 20060317)
[ 0.953137] ACPI: SSDT BFFDBCA3, 05FA (r1 HP Cpu0Cst 3001 INTL 20060317)
[ 0.959411] Monitor-Mwait will be used to enter C-1 state
[ 0.959417] Monitor-Mwait will be used to enter C-2 state
[ 0.959421] Monitor-Mwait will be used to enter C-3 state
[ 0.959573] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 0.959610] processor ACPI_CPU:00: registered as cooling_device11
[ 0.959613] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.959941] ACPI: SSDT BFFDB895, 00C8 (r1 HP Cpu1Ist 3000 INTL 20060317)
[ 0.960295] ACPI: SSDT BFFDBC1E, 0085 (r1 HP Cpu1Cst 3000 INTL 20060317)
[ 0.961309] Marking TSC unstable due to TSC halts in idle
[ 0.993122] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 0.993188] processor ACPI_CPU:01: registered as cooling_device12
[ 0.993198] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.999203] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.001416] ACPI: Thermal Zone [TZ2] (39 C)
[ 1.016096] thermal LNXTHERM:02: registered as thermal_zone1
[ 1.017808] ACPI: Thermal Zone [TZ3] (33 C)
[ 1.024692] thermal LNXTHERM:03: registered as thermal_zone2
[ 1.036763] ACPI: Thermal Zone [TZ4] (33 C)
[ 1.039495] thermal LNXTHERM:04: registered as thermal_zone3
[ 1.045453] ACPI: Thermal Zone [TZ5] (73 C)
[ 1.063577] thermal LNXTHERM:05: registered as thermal_zone4
[ 1.072712] ACPI: Thermal Zone [TZ0] (51 C)
[ 1.075758] thermal LNXTHERM:06: registered as thermal_zone5
[ 1.077596] ACPI: Thermal Zone [TZ1] (53 C)
[ 1.084652] device-mapper: uevent: version 1.0.3
[ 1.084870] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 1.314054] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
[ 1.314056] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 1.314100] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.314109] e1000e 0000:00:19.0: setting latency timer to 64
[ 1.314227] e1000e 0000:00:19.0: irq 28 for MSI/MSI-X
[ 1.338917] usbcore: registered new interface driver usbfs
[ 1.338944] usbcore: registered new interface driver hub
[ 1.353992] usbcore: registered new device driver usb
[ 1.365279] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.366493] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.375539] SCSI subsystem initialized
[ 1.377861] ohci1394 0000:02:06.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.389171] libata version 3.00 loaded.
[ 1.438164] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[e4102000-e41027ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 1.500103] Clocksource tsc unstable (delta = -71030829 ns)
[ 1.522477] 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1a:4b:7a:9d:98
[ 1.522479] 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[ 1.522508] 0000:00:19.0: eth0: MAC: 5, PHY: 6, PBA No: ffffff-0ff
[ 1.522737] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.522902] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.522906] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.522939] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 1.526843] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.526850] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.526854] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe4541000
[ 1.541125] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.541243] usb usb1: configuration #1 chosen from 1 choice
[ 1.541288] hub 1-0:1.0: USB hub found
[ 1.541298] hub 1-0:1.0: 4 ports detected
[ 1.541429] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.541437] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.541440] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.541458] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 2
[ 1.541490] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00005060
[ 1.541548] usb usb2: configuration #1 chosen from 1 choice
[ 1.541570] hub 2-0:1.0: USB hub found
[ 1.541575] hub 2-0:1.0: 2 ports detected
[ 1.541679] ata_piix 0000:00:1f.1: version 2.12
[ 1.541687] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.541722] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.541785] scsi0 : ata_piix
[ 1.541848] scsi1 : ata_piix
[ 1.542420] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x5100 irq 14
[ 1.542423] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x5108 irq 15
[ 1.704483] ata1.00: ATAPI: MATSHITADVD-RAM UJ-860H, 1.02, max MWDMA2
[ 1.720427] ata1.00: configured for MWDMA2
[ 1.723149] scsi 0:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-860H 1.02 PQ: 0 ANSI: 5
[ 1.723337] ata2: port disabled. ignoring.
[ 1.723396] ahci 0000:00:1f.2: version 3.0
[ 1.723408] ahci 0000:00:1f.2: PCI INT D -> GSI 21 (level, low) -> IRQ 21
[ 1.723452] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[ 1.723490] ahci: SSS flag set, parallel bus scan disabled
[ 1.723513] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode
[ 1.723515] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part
[ 1.723521] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.723613] scsi2 : ahci
[ 1.723655] scsi3 : ahci
[ 1.723695] scsi4 : ahci
[ 1.723744] ata3: SATA max UDMA/133 abar m2048@0xe4549000 port 0xe4549100 irq 29
[ 1.723746] ata4: DUMMY
[ 1.723747] ata5: DUMMY
[ 1.729339] Driver 'sr' needs updating - please use bus_type methods
[ 1.737182] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.737187] Uniform CD-ROM driver Revision: 3.20
[ 1.737302] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.741493] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.044125] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.046611] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 2.046613] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 filtered out
[ 2.046891] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
[ 2.046895] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 2.047604] ata3.00: ATA-8: Hitachi HTS722012K9SA00, DCCOC80A, max UDMA/100
[ 2.047608] ata3.00: 234441648 sectors, multi 16: LBA48
[ 2.050323] ata3.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
[ 2.050325] ata3.00: ACPI cmd b1/c1:00:00:00:00:a0 filtered out
[ 2.050540] ata3.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
[ 2.050545] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 2.051338] ata3.00: configured for UDMA/100
[ 2.069949] ata3.00: configured for UDMA/100
[ 2.069954] ata3: EH complete
[ 2.070091] scsi 2:0:0:0: Direct-Access ATA Hitachi HTS72201 DCCO PQ: 0 ANSI: 5
[ 2.070191] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.070289] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.070318] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.070321] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.070347] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 2.074259] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.074265] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.074279] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe4548000
[ 2.081372] Driver 'sd' needs updating - please use bus_type methods
[ 2.081439] sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 2.081456] sd 2:0:0:0: [sda] Write Protect is off
[ 2.081458] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.081474] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.081515] sd 2:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 2.081525] sd 2:0:0:0: [sda] Write Protect is off
[ 2.081527] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.081543] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.081546] sda: sda1 sda2 < sda5 >
[ 2.117503] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.133120] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 2.145120] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.145244] usb usb3: configuration #1 chosen from 1 choice
[ 2.145300] hub 3-0:1.0: USB hub found
[ 2.145311] hub 3-0:1.0: 6 ports detected
[ 2.145823] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.145834] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.145837] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.145858] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.145896] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00005080
[ 2.145965] usb usb4: configuration #1 chosen from 1 choice
[ 2.145986] hub 4-0:1.0: USB hub found
[ 2.145991] hub 4-0:1.0: 2 ports detected
[ 2.146071] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.146078] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.146082] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.146104] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.146130] uhci_hcd 0000:00:1d.0: irq 20, io base 0x000050a0
[ 2.146195] usb usb5: configuration #1 chosen from 1 choice
[ 2.146218] hub 5-0:1.0: USB hub found
[ 2.146223] hub 5-0:1.0: 2 ports detected
[ 2.146313] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 2.146319] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.146322] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.146340] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.146371] uhci_hcd 0000:00:1d.1: irq 22, io base 0x000050c0
[ 2.146435] usb usb6: configuration #1 chosen from 1 choice
[ 2.146456] hub 6-0:1.0: USB hub found
[ 2.146461] hub 6-0:1.0: 2 ports detected
[ 2.146537] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.146543] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.146546] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.146562] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.146587] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000050e0
[ 2.146653] usb usb7: configuration #1 chosen from 1 choice
[ 2.146675] hub 7-0:1.0: USB hub found
[ 2.146680] hub 7-0:1.0: 2 ports detected
[ 2.310640] usb 2-1: configuration #1 chosen from 1 choice
[ 2.353780] PM: Starting manual resume from disk
[ 2.353782] PM: Resume from partition 8:5
[ 2.353783] PM: Checking hibernation image.
[ 2.353962] PM: Resume from disk failed.
[ 2.404475] kjournald starting. Commit interval 5 seconds
[ 2.404481] EXT3-fs: mounted filesystem with ordered data mode.
[ 2.712274] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f9929ed5e0e]
[ 2.873117] usb 5-2: new full speed USB device using uhci_hcd and address 2
[ 3.038307] usb 5-2: configuration #1 chosen from 1 choice
[ 8.096793] udevd version 124 started
[ 8.465224] device-mapper: multipath: version 1.0.5 loaded
[ 8.588129] iTCO_vendor_support: vendor-support=0
[ 8.589305] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 8.589439] iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
[ 8.589501] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.649133] input: Power Button (FF) as /class/input/input1
[ 8.652799] input: PC Speaker as /class/input/input2
[ 8.669097] ACPI: Power Button (FF) [PWRF]
[ 8.669201] input: Sleep Button (CM) as /class/input/input3
[ 8.705081] ACPI: Sleep Button (CM) [C274]
[ 8.705146] input: Lid Switch as /class/input/input4
[ 8.713166] ACPI: Lid Switch [C26E]
[ 8.841161] ACPI: Battery Slot [C1F4] (battery present)
[ 8.841790] ACPI: Battery Slot [C1F3] (battery absent)
[ 8.872717] ACPI: AC Adapter [C1F2] (off-line)
[ 8.941270] acpi device:03: registered as cooling_device13
[ 8.942281] input: Video Bus as /class/input/input5
[ 8.968105] ACPI: Video Device [C14B] (multi-head: yes rom: no post: no)
[ 9.068764] yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30c5]
[ 9.104862] tpm_inf_pnp 00:03: Found C239 with ID IFX0102
[ 9.104913] tpm_inf_pnp 00:03: TPM found: config base 0x560, data base 0x570, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
[ 9.112419] lis3lv02d: 2-byte sensor found
[ 9.112423] lis3lv02d: hardware type NC8510 found.
[ 9.112440] Registered led device: hp::hddprotect
[ 9.123967] input: ST LIS3LV02DL Accelerometer as /class/input/input6
[ 9.128085] lis3_init_device: irq 23
[ 9.128087] lis3: registering device
[ 9.128126] lis3lv02d driver loaded.
[ 9.184375] ACPI: WMI: Mapper loaded
[ 9.197884] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0cb8, PCI irq 16
[ 9.197888] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 9.197893] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 9.197895] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xe4100000 - 0xe43fffff
[ 9.197898] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xcbffffff
[ 9.198092] yenta_cardbus 0000:02:06.1: CardBus bridge found [103c:30c5]
[ 9.200759] Bluetooth: Core ver 2.14
[ 9.202703] NET: Registered protocol family 31
[ 9.202704] Bluetooth: HCI device and connection manager initialized
[ 9.202707] Bluetooth: HCI socket layer initialized
[ 9.220049] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 9.220054] ricoh-mmc: Copyright(c) Philip Langdale
[ 9.233098] cfg80211: Calling CRDA to update world regulatory domain
[ 9.258786] sdhci: Secure Digital Host Controller Interface driver
[ 9.258788] sdhci: Copyright(c) Pierre Ossman
[ 9.276615] Bluetooth: Generic Bluetooth USB driver ver 0.4
[ 9.277354] usbcore: registered new interface driver btusb
[ 9.325843] yenta_cardbus 0000:02:06.1: ISA IRQ mask 0x0000, PCI irq 17
[ 9.325846] yenta_cardbus 0000:02:06.1: Socket status: 30000810
[ 9.325849] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #04 to #07
[ 9.325857] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 9.325859] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge Memory window: 0xe4100000 - 0xe43fffff
[ 9.325861] yenta_cardbus 0000:02:06.1: pcmcia: parent PCI bridge Memory window: 0xc4000000 - 0xcbffffff
[ 9.327385] parport_pc 00:02: reported by Plug and Play ACPI
[ 9.327461] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 9.329406] ricoh-mmc: Ricoh MMC controller found at 0000:02:06.4 [1180:0843] (rev 10)
[ 9.329424] ricoh-mmc: Controller is now disabled.
[ 9.329463] sdhci-pci 0000:02:06.3: SDHCI controller found [1180:0822] (rev 20)
[ 9.329480] sdhci-pci 0000:02:06.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 9.331556] Registered led device: mmc0::
[ 9.332608] mmc0: SDHCI controller on PCI [0000:02:06.3] using PIO
[ 9.385325] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[ 9.385335] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 9.385377] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 9.414833] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 9.414835] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 9.414956] iwlagn 0000:10:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 9.414966] iwlagn 0000:10:00.0: setting latency timer to 64
[ 9.415063] iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
[ 9.477827] iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
[ 9.478632] iwlagn 0000:10:00.0: PCI INT A disabled
[ 9.478702] wmaster0 (iwlagn): not using net_device_ops yet
[ 9.478919] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 9.519524] wlan0 (iwlagn): not using net_device_ops yet
[ 9.588873] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 9.588947] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 9.826066] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa44793/0x300000
[ 9.826073] serio: Synaptics pass-through port at isa0060/serio4/input0
[ 9.867525] input: SynPS/2 Synaptics TouchPad as /class/input/input7
[ 9.965115] pcmcia_socket pcmcia_socket1: pccard: PCMCIA card inserted into slot 1
[ 9.997116] pcmcia_socket pcmcia_socket1: cs: memory probe 0xc4000000-0xcbffffff: excluding 0xc4000000-0xcbffffff
[ 9.997146] pcmcia_socket pcmcia_socket1: cs: memory probe 0xe4100000-0xe43fffff: excluding 0xe4100000-0xe412ffff
[ 10.002436] pcmcia 1.0: pcmcia: registering new device pcmcia1.0
[ 10.139601] lp0: using parport0 (interrupt-driven).
[ 10.231311] Adding 4803392k swap on /dev/sda5. Priority:-1 extents:1 across:4803392k
[ 10.245666] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 10.246008] EXT3 FS on sda1, internal journal
[ 10.832908] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.552720] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 12.957190] NET: Registered protocol family 10
[ 12.957567] lo: Disabled Privacy Extensions
[ 14.544665] input: PS/2 Generic Mouse as /class/input/input8
[ 16.481559] ppdev: user-space parallel port driver
[ 18.372340] Bridge firewalling registered
[ 18.456354] vnet0: starting userspace STP failed, starting kernel STP
[ 18.788598] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 18.788808] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 18.788810] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[ 18.788812] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 22.318405] Bluetooth: L2CAP ver 2.11
[ 22.318410] Bluetooth: L2CAP socket layer initialized
[ 22.339950] Bluetooth: SCO (Voice Link) ver 0.6
[ 22.339956] Bluetooth: SCO socket layer initialized
[ 22.355128] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.355135] Bluetooth: BNEP filters: protocol multicast
[ 22.448322] Bluetooth: RFCOMM socket layer initialized
[ 22.448342] Bluetooth: RFCOMM TTY layer initialized
[ 22.448346] Bluetooth: RFCOMM ver 1.10
[ 24.668285] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 26.881563] e1000e 0000:00:19.0: irq 28 for MSI/MSI-X
[ 26.936306] e1000e 0000:00:19.0: irq 28 for MSI/MSI-X
[ 26.937868] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.942792] iwlagn 0000:10:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 26.942931] iwlagn 0000:10:00.0: restoring config space at offset 0x1 (was 0x100002, writing 0x100006)
[ 26.943099] iwlagn 0000:10:00.0: irq 30 for MSI/MSI-X
[ 26.943212] iwlagn 0000:10:00.0: firmware: requesting iwlwifi-4965-2.ucode
[ 27.202613] iwlagn loaded firmware version 228.57.2.23
[ 27.409469] Registered led device: iwl-phy0:radio
[ 27.410077] Registered led device: iwl-phy0:assoc
[ 27.411811] Registered led device: iwl-phy0:RX
[ 27.411899] Registered led device: iwl-phy0:TX
[ 27.453545] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.574154] NET: Registered protocol family 17
[ 28.605052] vnet0: no IPv6 routers present
[ 38.049145] CE: hpet increasing min_delta_ns to 15000 nsec
[ 102.421511] Monitor-Mwait will be used to enter C-2 state
[ 108.145656] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 108.146919] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 118.780098] eth0: no IPv6 routers present
[ 134.340199] ppdev0: registered pardevice
[ 134.388093] ppdev0: unregistered pardevice
[ 134.668443] ppdev0: registered pardevice
[ 134.716425] ppdev0: unregistered pardevice
[ 136.331159] ppdev0: registered pardevice
[ 136.377183] ppdev0: unregistered pardevice
[ 146.660545] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 146.661674] input: Bluetooth Laser Travel Mouse as /class/input/input9
[ 146.685182] generic-bluetooth 0005:046D:B008.0001: input,hidraw0: BLUETOOTH HID v3.13 Mouse [Bluetooth Laser Travel Mouse] on 00:1E:37:6E:FD:70
[ 2885.888003] irq 19: nobody cared (try booting with the "irqpoll" option)
[ 2885.888014] Pid: 0, comm: swapper Not tainted 2.6.29.1 #1
[ 2885.888019] Call Trace:
[ 2885.888023] <IRQ> [<ffffffff802751cb>] __report_bad_irq+0x38/0x87
[ 2885.888045] [<ffffffff80275332>] note_interrupt+0x118/0x182
[ 2885.888053] [<ffffffff80275962>] handle_fasteoi_irq+0xa1/0xc5
[ 2885.888062] [<ffffffff8020de49>] do_IRQ+0x70/0xe7
[ 2885.888069] [<ffffffff8020bf53>] ret_from_intr+0x0/0xa
[ 2885.888073] <EOI> [<ffffffff8024f317>] ? notifier_call_chain+0x33/0x5b
[ 2885.888136] [<ffffffffa002b7bb>] ? acpi_idle_enter_simple+0x186/0x1f8 [processor]
[ 2885.888159] [<ffffffffa002b7b1>] ? acpi_idle_enter_simple+0x17c/0x1f8 [processor]
[ 2885.888169] [<ffffffff80399fa6>] ? cpuidle_idle_call+0x8c/0xc6
[ 2885.888176] [<ffffffff8020a649>] ? cpu_idle+0x52/0x93
[ 2885.888184] [<ffffffff804133cd>] ? rest_init+0x61/0x63
[ 2885.888189] handlers:
[ 2885.888192] [<ffffffffa02b2b86>] (sdhci_irq+0x0/0x49a [sdhci])
[ 2885.888208] Disabling IRQ #19
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [Sdhci-devel] 2.6.29.1 sdhci: irq 19: nobody cared
2009-04-17 15:00 2.6.29.1 sdhci: irq 19: nobody cared Alessandro Bono
@ 2009-06-03 20:09 ` Pierre Ossman
0 siblings, 0 replies; 2+ messages in thread
From: Pierre Ossman @ 2009-06-03 20:09 UTC (permalink / raw)
To: Alessandro Bono; +Cc: sdhci-devel, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1012 bytes --]
On Fri, 17 Apr 2009 17:00:18 +0200
Alessandro Bono <alessandro.bono@gmail.com> wrote:
> Hi
>
> This is a bug that occur from time to time on my (unsed) sdhci card
> drive
> this is with kernel 2.6.29.1 (not a regression, I had the same problem
> with older kernel)
>
> [ 2885.888003] irq 19: nobody cared (try booting with the "irqpoll"
> option)
Unfortunately it's most likely something else, which happens to be
sharing the interrupt line with the SD controller. Please try to get in
touch with the Linux ACPI people. They are generally very good at
sorting out irq issues.
Rgds
--
-- Pierre Ossman
Linux kernel, MMC maintainer http://www.kernel.org
rdesktop, core developer http://www.rdesktop.org
TigerVNC, core developer http://www.tigervnc.org
WARNING: This correspondence is being monitored by the
Swedish government. Make sure your server uses encryption
for SMTP traffic and consider using PGP for end-to-end
encryption.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 198 bytes --]
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2009-06-03 20:09 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-04-17 15:00 2.6.29.1 sdhci: irq 19: nobody cared Alessandro Bono
2009-06-03 20:09 ` [Sdhci-devel] " Pierre Ossman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox