* usb fails to suspend [was: mmotm 2009-06-05-16-19]
@ 2009-06-06 17:16 Jiri Slaby
2009-06-06 22:28 ` Rafael J. Wysocki
2009-06-07 8:48 ` Marcel Holtmann
0 siblings, 2 replies; 7+ messages in thread
From: Jiri Slaby @ 2009-06-06 17:16 UTC (permalink / raw)
To: rjw@sisk.pl; +Cc: Alan Stern, Andrew Morton, Linux kernel mailing list
Hi,
there is a suspend regression somewhere between mmotm 2009-05-17-12-15
and 2009-06-05-16-19:
hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19
pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19
pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19
$ lspci -xxvvs 0000:00:1d.2
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d000 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
Any ideas?
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-06 17:16 usb fails to suspend [was: mmotm 2009-06-05-16-19] Jiri Slaby
@ 2009-06-06 22:28 ` Rafael J. Wysocki
2009-06-07 20:36 ` Jiri Slaby
2009-06-07 8:48 ` Marcel Holtmann
1 sibling, 1 reply; 7+ messages in thread
From: Rafael J. Wysocki @ 2009-06-06 22:28 UTC (permalink / raw)
To: Jiri Slaby; +Cc: Alan Stern, Andrew Morton, Linux kernel mailing list
On Saturday 06 June 2009, Jiri Slaby wrote:
> Hi,
>
> there is a suspend regression somewhere between mmotm 2009-05-17-12-15
> and 2009-06-05-16-19:
> hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19
> pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19
> pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
> PM: Device 0000:00:1d.2 failed to suspend late: error -19
>
> $ lspci -xxvvs 0000:00:1d.2
> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #3 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #3
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin D routed to IRQ 16
> Region 4: I/O ports at d000 [size=32]
> Capabilities: [50] Vendor Specific Information <?>
> Kernel driver in use: uhci_hcd
> 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
>
> Any ideas?
Not really. Is it -mm-only or is the mainline affected too?
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-06 22:28 ` Rafael J. Wysocki
@ 2009-06-07 20:36 ` Jiri Slaby
2009-06-07 21:20 ` Rafael J. Wysocki
0 siblings, 1 reply; 7+ messages in thread
From: Jiri Slaby @ 2009-06-07 20:36 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Alan Stern, Andrew Morton, Linux kernel mailing list,
Jesse Barnes
On 06/07/2009 12:28 AM, Rafael J. Wysocki wrote:
> On Saturday 06 June 2009, Jiri Slaby wrote:
>> Hi,
>>
>> there is a suspend regression somewhere between mmotm 2009-05-17-12-15
>> and 2009-06-05-16-19:
>> hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19
>> pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19
>> pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
>> PM: Device 0000:00:1d.2 failed to suspend late: error -19
>>
>> $ lspci -xxvvs 0000:00:1d.2
>> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
>> Controller #3 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
>> Controller #3
>> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>> ParErr- Stepping- SERR- FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 0
>> Interrupt: pin D routed to IRQ 16
>> Region 4: I/O ports at d000 [size=32]
>> Capabilities: [50] Vendor Specific Information <?>
>> Kernel driver in use: uhci_hcd
>> 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
>> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
>> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
>>
>> Any ideas?
>
> Not really. Is it -mm-only or is the mainline affected too?
Yup, only an -mm thing. I reverted these two:
pci-pm-read-device-power-state-from-register-after-updating-it.patch
pci-pm-read-device-power-state-from-register-after-updating-it-update.patch
and it works now :).
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-07 20:36 ` Jiri Slaby
@ 2009-06-07 21:20 ` Rafael J. Wysocki
0 siblings, 0 replies; 7+ messages in thread
From: Rafael J. Wysocki @ 2009-06-07 21:20 UTC (permalink / raw)
To: Jiri Slaby, Andrew Morton
Cc: Alan Stern, Linux kernel mailing list, Jesse Barnes
On Sunday 07 June 2009, Jiri Slaby wrote:
> On 06/07/2009 12:28 AM, Rafael J. Wysocki wrote:
> > On Saturday 06 June 2009, Jiri Slaby wrote:
> >> Hi,
> >>
> >> there is a suspend regression somewhere between mmotm 2009-05-17-12-15
> >> and 2009-06-05-16-19:
> >> hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19
> >> pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19
> >> pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
> >> PM: Device 0000:00:1d.2 failed to suspend late: error -19
> >>
> >> $ lspci -xxvvs 0000:00:1d.2
> >> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> >> Controller #3 (rev 02) (prog-if 00 [UHCI])
> >> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
> >> Controller #3
> >> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> >> ParErr- Stepping- SERR- FastB2B- DisINTx-
> >> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> >> <TAbort- <MAbort- >SERR- <PERR- INTx-
> >> Latency: 0
> >> Interrupt: pin D routed to IRQ 16
> >> Region 4: I/O ports at d000 [size=32]
> >> Capabilities: [50] Vendor Specific Information <?>
> >> Kernel driver in use: uhci_hcd
> >> 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
> >> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> >> 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
> >> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
> >>
> >> Any ideas?
> >
> > Not really. Is it -mm-only or is the mainline affected too?
>
> Yup, only an -mm thing. I reverted these two:
> pci-pm-read-device-power-state-from-register-after-updating-it.patch
> pci-pm-read-device-power-state-from-register-after-updating-it-update.patch
> and it works now :).
OK, thanks.
Andrew, can you drop these two patches from -mm please?
Best,
Rafael
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-06 17:16 usb fails to suspend [was: mmotm 2009-06-05-16-19] Jiri Slaby
2009-06-06 22:28 ` Rafael J. Wysocki
@ 2009-06-07 8:48 ` Marcel Holtmann
2009-06-07 8:51 ` Jiri Slaby
1 sibling, 1 reply; 7+ messages in thread
From: Marcel Holtmann @ 2009-06-07 8:48 UTC (permalink / raw)
To: Jiri Slaby
Cc: rjw@sisk.pl, Alan Stern, Andrew Morton, Linux kernel mailing list
Hi Jiri,
> there is a suspend regression somewhere between mmotm 2009-05-17-12-15
> and 2009-06-05-16-19:
> hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19
> pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19
> pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
> PM: Device 0000:00:1d.2 failed to suspend late: error -19
>
> $ lspci -xxvvs 0000:00:1d.2
> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #3 (rev 02) (prog-if 00 [UHCI])
> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #3
what is the likelihood that you have an Intel WiMAX card in this system?
There is a suspend issue when i2400m_usb is loaded. Took me a while to
figure that one out. It suspends/resumes fine for the first time after
reboot, but on resume it deadlocks the whole USB subsystem.
Regards
Marcel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-07 8:48 ` Marcel Holtmann
@ 2009-06-07 8:51 ` Jiri Slaby
2009-06-07 8:52 ` Marcel Holtmann
0 siblings, 1 reply; 7+ messages in thread
From: Jiri Slaby @ 2009-06-07 8:51 UTC (permalink / raw)
To: Marcel Holtmann
Cc: rjw@sisk.pl, Alan Stern, Andrew Morton, Linux kernel mailing list
On 06/07/2009 10:48 AM, Marcel Holtmann wrote:
> Hi Jiri,
Hi.
>> $ lspci -xxvvs 0000:00:1d.2
>> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
>> Controller #3 (rev 02) (prog-if 00 [UHCI])
>> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
>> Controller #3
>
> what is the likelihood that you have an Intel WiMAX card in this system?
None :) -- I have no such card in the system.
> There is a suspend issue when i2400m_usb is loaded. Took me a while to
> figure that one out. It suspends/resumes fine for the first time after
> reboot, but on resume it deadlocks the whole USB subsystem.
This was the first time I tried to suspend.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: usb fails to suspend [was: mmotm 2009-06-05-16-19]
2009-06-07 8:51 ` Jiri Slaby
@ 2009-06-07 8:52 ` Marcel Holtmann
0 siblings, 0 replies; 7+ messages in thread
From: Marcel Holtmann @ 2009-06-07 8:52 UTC (permalink / raw)
To: Jiri Slaby
Cc: rjw@sisk.pl, Alan Stern, Andrew Morton, Linux kernel mailing list
Hi Jiri,
> >> $ lspci -xxvvs 0000:00:1d.2
> >> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> >> Controller #3 (rev 02) (prog-if 00 [UHCI])
> >> Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
> >> Controller #3
> >
> > what is the likelihood that you have an Intel WiMAX card in this system?
>
> None :) -- I have no such card in the system.
>
> > There is a suspend issue when i2400m_usb is loaded. Took me a while to
> > figure that one out. It suspends/resumes fine for the first time after
> > reboot, but on resume it deadlocks the whole USB subsystem.
>
> This was the first time I tried to suspend.
then it is not that issue and I have no idea what happens.
Regards
Marcel
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2009-06-07 21:20 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-06-06 17:16 usb fails to suspend [was: mmotm 2009-06-05-16-19] Jiri Slaby
2009-06-06 22:28 ` Rafael J. Wysocki
2009-06-07 20:36 ` Jiri Slaby
2009-06-07 21:20 ` Rafael J. Wysocki
2009-06-07 8:48 ` Marcel Holtmann
2009-06-07 8:51 ` Jiri Slaby
2009-06-07 8:52 ` Marcel Holtmann
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox