[PATCH net v2 1/1] net: stmmac: update MAC capabilities when tx queues are updated

[PATCH net v2 1/1] net: stmmac: update MAC capabilities when tx queues are updated

[Gan Yi Fang]

From: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>

Upon boot up, the driver will configure the MAC capabilities based on
the maximum number of tx and rx queues. When the user changes the
tx queues to single queue, the MAC should be capable of supporting Half
Duplex, but the driver does not update the MAC capabilities when it is
configured so.

Using the stmmac_reinit_queues() to check the number of tx queues
and set the MAC capabilities accordingly.

Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Cc: <stable@vger.kernel.org> # 5.17+
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
---
 .../net/ethernet/stmicro/stmmac/stmmac_main.c   | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index ed1a5a31a491..5801f4d50f95 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1197,6 +1197,17 @@ static int stmmac_init_phy(struct net_device *dev)
 	return ret;
 }
 
+static void stmmac_set_half_duplex(struct stmmac_priv *priv)
+{
+	/* Half-Duplex can only work with single tx queue */
+	if (priv->plat->tx_queues_to_use > 1)
+		priv->phylink_config.mac_capabilities &=
+			~(MAC_10HD | MAC_100HD | MAC_1000HD);
+	else
+		priv->phylink_config.mac_capabilities |=
+			(MAC_10HD | MAC_100HD | MAC_1000HD);
+}
+
 static int stmmac_phy_setup(struct stmmac_priv *priv)
 {
 	struct stmmac_mdio_bus_data *mdio_bus_data;
@@ -1228,10 +1239,7 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 						MAC_10FD | MAC_100FD |
 						MAC_1000FD;
 
-	/* Half-Duplex can only work with single queue */
-	if (priv->plat->tx_queues_to_use <= 1)
-		priv->phylink_config.mac_capabilities |= MAC_10HD | MAC_100HD |
-							 MAC_1000HD;
+	stmmac_set_half_duplex(priv);
 
 	/* Get the MAC specific capabilities */
 	stmmac_mac_phylink_get_caps(priv);
@@ -7172,6 +7180,7 @@ int stmmac_reinit_queues(struct net_device *dev, u32 rx_cnt, u32 tx_cnt)
 			priv->rss.table[i] = ethtool_rxfh_indir_default(i,
 									rx_cnt);
 
+	stmmac_set_half_duplex(priv);
 	stmmac_napi_add(dev);
 
 	if (netif_running(dev))
-- 
2.34.1

Re: [PATCH net v2 1/1] net: stmmac: update MAC capabilities when tx queues are updated

[patchwork-bot+netdevbpf]

Hello:

This patch was applied to netdev/net.git (main)
by David S. Miller <davem@davemloft.net>:

On Fri, 20 Oct 2023 11:25:35 +0800 you wrote:
> From: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
> 
> Upon boot up, the driver will configure the MAC capabilities based on
> the maximum number of tx and rx queues. When the user changes the
> tx queues to single queue, the MAC should be capable of supporting Half
> Duplex, but the driver does not update the MAC capabilities when it is
> configured so.
> 
> [...]

Here is the summary with links:
  - [net,v2,1/1] net: stmmac: update MAC capabilities when tx queues are updated
    https://git.kernel.org/netdev/net/c/95201f36f395

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html