Re: Null Pointer BUG in uhci_hcd

["Michael S. Zick" <lkml@morethan.org>]

On Wed July 8 2009, Michael S. Zick wrote:
> On Wed July 8 2009, Alan Stern wrote:
> > On Wed, 8 Jul 2009, Michael S. Zick wrote:
> > 
> > > But, then again, we might just get lucky:
> > > ehci_hcd 0000:00:10.4: Unlink after no-IRQ?  Controller is probably using the wrong IRQ.
> > > usb 1-5: khubd timed out on ep0in len=18/64
> > 
> > Like I've been telling you all along, the hardware isn't working.  I 
> > suspect it's worse than a simple interrupt-routing mistake.
> > 
> > > > > For more information enable CONFIG_USB_DEBUG and CONFIG_DEBUG_FS, then 
> > > > > see what's sitting in the usb/uhci/* files in debugfs.
> > > > > 
> > > 
> > > Anything in particular to look for/at?
> > 
> > Just post the contents of those files.
> >
> Done:
> 

All "BUG" statements out - -
Still does not notice plugging in an external device.
Nothing, zip, nada in the dmesg as a result of plug/unplug.

Mike
> root@cb01:/sys/kernel/debug/uhci# cat *
> Root-hub state: suspended   FSBR: 0
> HC status
>   usbcmd    =     0048   Maxp32 CF EGSM
>   usbstat   =     0020   HCHalted
>   usbint    =     0002
>   usbfrnum  =   (1)4a8
>   flbaseadd = 19c7f000
>   sof       =       40
>   stat1     =     0480   OverCurrent
>   stat2     =     0480   OverCurrent
> Most recent frame: 52a (298)   Last ISO frame: 52a (298)
> Periodic load table
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
> Total: 0, #INT: 0, #ISO: 0
> Root-hub state: suspended   FSBR: 0
> HC status
>   usbcmd    =     0048   Maxp32 CF EGSM
>   usbstat   =     0020   HCHalted
>   usbint    =     0002
>   usbfrnum  =   (1)4a0
>   flbaseadd = 19c63000
>   sof       =       40
>   stat1     =     0480   OverCurrent
>   stat2     =     0480   OverCurrent
> Most recent frame: 528 (296)   Last ISO frame: 528 (296)
> Periodic load table
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
> Total: 0, #INT: 0, #ISO: 0
> Root-hub state: running   FSBR: 0
> HC status
>   usbcmd    =     00c1   Maxp64 CF RS
>   usbstat   =     0000
>   usbint    =     000f
>   usbfrnum  =   (0)c1c
>   flbaseadd = 19c9c000
>   sof       =       40
>   stat1     =     0495   OverCurrent Enabled Connected
>   stat2     =     0495   OverCurrent Enabled Connected
> Most recent frame: 56aee (750)   Last ISO frame: 56aee (750)
> Periodic load table
>         0       0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
>         17      0       0       0       0       0       0       0
>         0       0       0       0       0       0       0       0
> Total: 17, #INT: 1, #ISO: 0
> 
> And, at no extra cost:
> 
> root@cb01:/sys/kernel/debug/ehci/0000:00:10.4# cat *
> size = 256
> bus pci, device 0000:00:10.4
> EHCI Host Controller
> EHCI 1.00, hcd state 4
> ownership 01000001 linux
> SMI sts/enable 0xe00f0000
> structural params 0x00103206
> capability params 0x00006872
> status 100f Halt FLR PCD ERR INT
> command 010008 (park)=0 ithresh=1 period=256 HALT
> intrenable 37 IAA FATAL PCD ERR INT
> uframe 14db
> port 1 status 701000 POWER sig=se0
> port 2 status 701000 POWER sig=se0
> port 3 status 701000 POWER sig=se0
> port 4 status 701000 POWER sig=se0
> port 5 status 703802 POWER OWNER sig=j CSC
> port 6 status 703802 POWER OWNER sig=j CSC
> irq normal 0 err 0 reclaim 0 (lost 20)
> complete 0 unlink 20
> 
> Mike 
> > Alan Stern
> > 
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at  http://www.tux.org/lkml/
> > 
> > 
> 
> 
>