[PATCH] dt-bindings: dmaengine: Add MediaTek Command-Queue DMA controller bindings

[PATCH] dt-bindings: dmaengine: Add MediaTek Command-Queue DMA controller bindings

[shun-chih.yu]

Add document the devicetree bindings for MediaTek Command-Queue DMA controller.

[PATCH 1/1] dt-bindings: dmaengine: Add MediaTek Command-Queue DMA controller bindings

[shun-chih.yu]

From: Shun-Chih Yu <shun-chih.yu@mediatek.com>

Document the devicetree bindings for MediaTek Command-Queue DMA controller
which could be found on MT6765 SoC or other similar Mediatek SoCs.

Change-Id: I9736c8cac9be160358feeab935fabaffc5730519
Signed-off-by: Shun-Chih Yu <shun-chih.yu@mediatek.com>
---
 .../devicetree/bindings/dma/mtk-cqdma.txt          |   31 ++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/dma/mtk-cqdma.txt

diff --git a/Documentation/devicetree/bindings/dma/mtk-cqdma.txt b/Documentation/devicetree/bindings/dma/mtk-cqdma.txt
new file mode 100644
index 0000000..fb12927
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/mtk-cqdma.txt
@@ -0,0 +1,31 @@
+MediaTek Command-Queue DMA Controller
+==================================
+
+Required properties:
+
+- compatible:	Must be "mediatek,mt6765-cqdma" for MT6765.
+- reg:		Should contain the base address and length for each channel.
+- interrupts:	Should contain references to the interrupts for each channel.
+- clocks:	Should be the clock specifiers corresponding to the entry in
+		clock-names property.
+- clock-names:	Should contain "cqdma" entries.
+- dma-channels: The number of DMA channels supported by the controller.
+- dma-requests: The number of DMA request supported by the controller.
+- #dma-cells: 	The length of the DMA specifier, must be <1>. This one cell
+		in dmas property of a client device represents the channel
+		number.
+Example:
+
+        cqdma: dma-controller@10212000 {
+		compatible = "mediatek,mt6765-cqdma";
+		reg = <0 0x10212000 0 0x1000>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>,
+			<GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&infracfg CLK_IFR_CQ_DMA>;
+		clock-names = "cqdma";
+		dma-channels = <2>;
+		dma-requests = <32>;
+		#dma-cells = <1>;
+	};
+
+DMA clients must use the format described in dma/dma.txt file.
-- 
1.7.9.5

Re: [PATCH 1/1] dt-bindings: dmaengine: Add MediaTek Command-Queue DMA controller bindings

[Rob Herring]

On Thu, Feb 14, 2019 at 03:40:58PM +0800, shun-chih.yu@mediatek.com wrote:
> From: Shun-Chih Yu <shun-chih.yu@mediatek.com>
> 
> Document the devicetree bindings for MediaTek Command-Queue DMA controller
> which could be found on MT6765 SoC or other similar Mediatek SoCs.
> 
> Change-Id: I9736c8cac9be160358feeab935fabaffc5730519

Drop this.

> Signed-off-by: Shun-Chih Yu <shun-chih.yu@mediatek.com>
> ---
>  .../devicetree/bindings/dma/mtk-cqdma.txt          |   31 ++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/dma/mtk-cqdma.txt
> 
> diff --git a/Documentation/devicetree/bindings/dma/mtk-cqdma.txt b/Documentation/devicetree/bindings/dma/mtk-cqdma.txt
> new file mode 100644
> index 0000000..fb12927
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/mtk-cqdma.txt
> @@ -0,0 +1,31 @@
> +MediaTek Command-Queue DMA Controller
> +==================================
> +
> +Required properties:
> +
> +- compatible:	Must be "mediatek,mt6765-cqdma" for MT6765.
> +- reg:		Should contain the base address and length for each channel.
> +- interrupts:	Should contain references to the interrupts for each channel.
> +- clocks:	Should be the clock specifiers corresponding to the entry in
> +		clock-names property.
> +- clock-names:	Should contain "cqdma" entries.
> +- dma-channels: The number of DMA channels supported by the controller.

What's the range of valid values?

> +- dma-requests: The number of DMA request supported by the controller.

What's the range of valid values?

> +- #dma-cells: 	The length of the DMA specifier, must be <1>. This one cell
> +		in dmas property of a client device represents the channel
> +		number.
> +Example:
> +
> +        cqdma: dma-controller@10212000 {
> +		compatible = "mediatek,mt6765-cqdma";
> +		reg = <0 0x10212000 0 0x1000>;

Should be 2 entries here since there are 2 channels? Or the description 
above is wrong.

> +		interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>,
> +			<GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>;
> +		clocks = <&infracfg CLK_IFR_CQ_DMA>;
> +		clock-names = "cqdma";
> +		dma-channels = <2>;
> +		dma-requests = <32>;
> +		#dma-cells = <1>;
> +	};
> +
> +DMA clients must use the format described in dma/dma.txt file.
> -- 
> 1.7.9.5
>