* Re: Query: CNSS WLAN.
[not found] <SN6PR04MB4142AB972E7046A24F1F911394EB0@SN6PR04MB4142.namprd04.prod.outlook.com>
@ 2020-02-27 18:40 ` John W. Linville
0 siblings, 0 replies; only message in thread
From: John W. Linville @ 2020-02-27 18:40 UTC (permalink / raw)
To: Singh, Varunpratap
Cc: grant.likely@linaro.org, robh+dt@kernel.org,
linux-wireless@vger.kernel.org, netdev@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
Nagaraj, Vinay
Varun,
Unfortunately, your questions is well outside of my areas of skill and
expertise. Hopefully Grant or someone else in your distribution list
will be more helpful.
Best regards!
John
On Thu, Feb 27, 2020 at 03:25:16PM +0000, Singh, Varunpratap wrote:
> Hi John,
>
> I am trying to bring up two wifi-modules simultaneously, on Qualcomm Snapdragon SD820 processor and the Kernel version is 3.18.
> I connected the modules on PCIe_0 & PCIe_1.
>
> As per my understanding the following device tree structure is responsible for driver probing.
> qcom,cnss {
> compatible = "qcom,cnss";
> wlan-bootstrap-gpio = <&tlmm 46 0>;
> vdd-wlan-en-supply = <&wlan_en_vreg>;
> vdd-wlan-supply = <&rome_vreg>;
> vdd-wlan-io-supply = <&pm8994_s4>;
> vdd-wlan-xtal-supply = <&pm8994_l30>;
> vdd-wlan-core-supply = <&pm8994_s3>;
> wlan-ant-switch-supply = <&pm8994_l18_pin_ctrl>;
> qcom,wlan-en-vreg-support;
> qcom,enable-bootstrap-gpio;
> qcom,notify-modem-status;
> pinctrl-names = "bootstrap_active", "bootstrap_sleep";
> pinctrl-0 = <&cnss_bootstrap_active>;
> pinctrl-1 = <&cnss_bootstrap_sleep>;
> qcom,wlan-rc-num = <0>;
> qcom,wlan-ramdump-dynamic = <0x200000>;
>
> qcom,msm-bus,name = "msm-cnss";
> qcom,msm-bus,num-cases = <4>;
> qcom,msm-bus,num-paths = <1>;
> qcom,msm-bus,vectors-KBps =
> /* No vote */
> <45 512 0 0>,
> /* Up to 200 Mbps */
> <45 512 41421 1520000>,
> /* Up to 400 Mbps */
> <45 512 96650 1520000>,
> /* Up to 800 Mbps */
> <45 512 207108 14432000>;
> };
>
> Currently if I change the "qcom,wlan-rc-num = <0>;" to "qcom,wlan-rc-num = <1>;" the module connected on PCIe_1 will start working and vice-versa. But as per the requirement we need two probe getting succeeded i.e both the modules should be registered. Please, suggest how can I create two different nodes under cnss structure.
>
> Any suggestion will be valuable.
>
>
>
> With Regards,
> Varun Pratap Singh
> Software Engineer.
--
John W. Linville Someday the world will need a hero, and you
linville@tuxdriver.com might be all we have. Be ready.
^ permalink raw reply [flat|nested] only message in thread