[PATCH v2 13/13] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes

[Vinod Koul <vkoul@kernel.org>]

From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Add device tree nodes for two i2c blocks: i2c13 and i2c14.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 94bc8b352547..c214ab89b44c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -583,6 +583,44 @@ uart7: serial@99c000 {
 			};
 		};
 
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_data_clk>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		config_noc: interconnect@1500000 {
 			compatible = "qcom,sm8450-config-noc";
 			reg = <0 0x01500000 0 0x1c000>;
@@ -683,6 +721,20 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 211>;
 			wakeup-parent = <&pdc>;
 
+			qup_i2c13_data_clk: qup-i2c13-data-clk {
+				pins = "gpio48", "gpio49";
+				function = "qup13";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c14_data_clk: qup-i2c14-data-clk {
+				pins = "gpio52", "gpio53";
+				function = "qup14";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
 			qup_uart7_rx: qup-uart7-rx {
 				pins = "gpio26";
 				function = "qup7";
-- 
2.31.1