[PATCH AUTOSEL 4.14 01/10] Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode

[PATCH AUTOSEL 4.14 01/10] Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode

[Sasha Levin]

From: Aman Dhoot <amandhoot12@gmail.com>

[ Upstream commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 ]

The device works fine in native RMI mode, there is no reason to use legacy
PS/2 mode with it.

Signed-off-by: Aman Dhoot <amandhoot12@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/input/mouse/synaptics.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/input/mouse/synaptics.c b/drivers/input/mouse/synaptics.c
index 0714d572e49a..53bd449a5e49 100644
--- a/drivers/input/mouse/synaptics.c
+++ b/drivers/input/mouse/synaptics.c
@@ -192,6 +192,7 @@ static const char * const smbus_pnp_ids[] = {
 	"SYN3221", /* HP 15-ay000 */
 	"SYN323d", /* HP Spectre X360 13-w013dx */
 	"SYN3257", /* HP Envy 13-ad105ng */
+	"SYN3286", /* HP Laptop 15-da3001TU */
 	NULL
 };
 
-- 
2.35.1

[PATCH AUTOSEL 4.14 02/10] serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ]

RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():

omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS.  If RTS uses active-low polarity, it is now asserted
for no reason.

The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register.  That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).

(up->mcr is not, as one might think, a cache of the MCR register's
current value.  Rather, it only caches a single bit of that register,
the AFE bit.  And it only does so if the UART supports the AFE bit,
which OMAP does not.  For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)

Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().

So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx().  Avoid by using a read-modify-write
when setting TCRTLR.

While at it, drop a redundant initialization of up->mcr.  As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c.  (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)

Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/8250/8250_omap.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index e32afaa94d36..c5af1495cd2e 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -259,6 +259,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
 {
 	struct omap8250_priv *priv = up->port.private_data;
 	struct uart_8250_dma	*dma = up->dma;
+	u8 mcr = serial8250_in_MCR(up);
 
 	if (dma && dma->tx_running) {
 		/*
@@ -275,7 +276,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
 	serial_out(up, UART_EFR, UART_EFR_ECB);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial8250_out_MCR(up, UART_MCR_TCRTLR);
+	serial8250_out_MCR(up, mcr | UART_MCR_TCRTLR);
 	serial_out(up, UART_FCR, up->fcr);
 
 	omap8250_update_scr(up, priv);
@@ -291,7 +292,8 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
 	serial_out(up, UART_LCR, 0);
 
 	/* drop TCR + TLR access, we setup XON/XOFF later */
-	serial8250_out_MCR(up, up->mcr);
+	serial8250_out_MCR(up, mcr);
+
 	serial_out(up, UART_IER, up->ier);
 
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -600,7 +602,6 @@ static int omap_8250_startup(struct uart_port *port)
 
 	pm_runtime_get_sync(port->dev);
 
-	up->mcr = 0;
 	serial_out(up, UART_FCR, UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 
 	serial_out(up, UART_LCR, UART_LCR_WLEN8);
-- 
2.35.1

[PATCH AUTOSEL 4.14 03/10] xen/platform-pci: add missing free_irq() in error path

[Sasha Levin]

From: ruanjinjie <ruanjinjie@huawei.com>

[ Upstream commit c53717e1e3f0d0f9129b2e0dbc6dcc5e0a8132e9 ]

free_irq() is missing in case of error in platform_pci_probe(), fix that.

Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Link: https://lore.kernel.org/r/20221114112124.1965611-1-ruanjinjie@huawei.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/xen/platform-pci.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/xen/platform-pci.c b/drivers/xen/platform-pci.c
index 4cec8146609a..c7e190e5db30 100644
--- a/drivers/xen/platform-pci.c
+++ b/drivers/xen/platform-pci.c
@@ -150,7 +150,7 @@ static int platform_pci_probe(struct pci_dev *pdev,
 		if (ret) {
 			dev_warn(&pdev->dev, "Unable to set the evtchn callback "
 					 "err=%d\n", ret);
-			goto out;
+			goto irq_out;
 		}
 	}
 
@@ -158,13 +158,16 @@ static int platform_pci_probe(struct pci_dev *pdev,
 	grant_frames = alloc_xen_mmio(PAGE_SIZE * max_nr_gframes);
 	ret = gnttab_setup_auto_xlat_frames(grant_frames);
 	if (ret)
-		goto out;
+		goto irq_out;
 	ret = gnttab_init();
 	if (ret)
 		goto grant_out;
 	return 0;
 grant_out:
 	gnttab_free_auto_xlat_frames();
+irq_out:
+	if (!xen_have_vector_callback)
+		free_irq(pdev->irq, pdev);
 out:
 	pci_release_region(pdev, 0);
 mem_out:
-- 
2.35.1

[PATCH AUTOSEL 4.14 04/10] platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()

[Sasha Levin]

From: Xiongfeng Wang <wangxiongfeng2@huawei.com>

[ Upstream commit d0cdd85046b15089df71a50548617ac1025300d0 ]

pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.

Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221111100752.134311-1-wangxiongfeng2@huawei.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/asus-wmi.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c
index af26ca49996d..ca17ab9873e2 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -1107,6 +1107,8 @@ static void asus_wmi_set_xusb2pr(struct asus_wmi *asus)
 	pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
 				cpu_to_le32(ports_available));
 
+	pci_dev_put(xhci_pdev);
+
 	pr_info("set USB_INTEL_XUSB2PR old: 0x%04x, new: 0x%04x\n",
 			orig_ports_available, ports_available);
 }
-- 
2.35.1

[PATCH AUTOSEL 4.14 05/10] platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)

[Sasha Levin]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit 1e817b889c7d8c14e7005258e15fec62edafe03c ]

Like the Acer Switch 10 (SW5-012) and Acer Switch 10 (S1003) models
the Acer Switch V 10 (SW5-017) supports reporting SW_TABLET_MODE
through acer-wmi.

Add a DMI quirk for the SW5-017 setting force_caps to ACER_CAP_KBD_DOCK
(these devices have no other acer-wmi based functionality).

Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221111111639.35730-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/acer-wmi.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c
index 8b4af118ff94..e2f054112fba 100644
--- a/drivers/platform/x86/acer-wmi.c
+++ b/drivers/platform/x86/acer-wmi.c
@@ -549,6 +549,15 @@ static const struct dmi_system_id acer_quirks[] __initconst = {
 		},
 		.driver_data = (void *)ACER_CAP_KBD_DOCK,
 	},
+	{
+		.callback = set_force_caps,
+		.ident = "Acer Aspire Switch V 10 SW5-017",
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "SW5-017"),
+		},
+		.driver_data = (void *)ACER_CAP_KBD_DOCK,
+	},
 	{
 		.callback = set_force_caps,
 		.ident = "Acer One 10 (S1003)",
-- 
2.35.1

[PATCH AUTOSEL 4.14 06/10] platform/x86: hp-wmi: Ignore Smart Experience App event

[Sasha Levin]

From: Kai-Heng Feng <kai.heng.feng@canonical.com>

[ Upstream commit 8b9b6a044b408283b086702b1d9e3cf4ba45b426 ]

Sometimes hp-wmi driver complains on system resume:
[ 483.116451] hp_wmi: Unknown event_id - 33 - 0x0

According to HP it's a feature called "HP Smart Experience App" and it's
safe to be ignored.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20221114073842.205392-1-kai.heng.feng@canonical.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/hp-wmi.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/platform/x86/hp-wmi.c b/drivers/platform/x86/hp-wmi.c
index f911410bb4c7..6f35becaa743 100644
--- a/drivers/platform/x86/hp-wmi.c
+++ b/drivers/platform/x86/hp-wmi.c
@@ -76,6 +76,7 @@ enum hp_wmi_event_ids {
 	HPWMI_PEAKSHIFT_PERIOD		= 0x0F,
 	HPWMI_BATTERY_CHARGE_PERIOD	= 0x10,
 	HPWMI_SANITIZATION_MODE		= 0x17,
+	HPWMI_SMART_EXPERIENCE_APP	= 0x21,
 };
 
 struct bios_args {
@@ -634,6 +635,8 @@ static void hp_wmi_notify(u32 value, void *context)
 		break;
 	case HPWMI_SANITIZATION_MODE:
 		break;
+	case HPWMI_SMART_EXPERIENCE_APP:
+		break;
 	default:
 		pr_info("Unknown event_id - %d - 0x%x\n", event_id, event_data);
 		break;
-- 
2.35.1

[PATCH AUTOSEL 4.14 07/10] tcp: configurable source port perturb table size

[Sasha Levin]

From: Gleb Mazovetskiy <glex.spb@gmail.com>

[ Upstream commit aeac4ec8f46d610a10adbaeff5e2edf6a88ffc62 ]

On embedded systems with little memory and no relevant
security concerns, it is beneficial to reduce the size
of the table.

Reducing the size from 2^16 to 2^8 saves 255 KiB
of kernel RAM.

Makes the table size configurable as an expert option.

The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5ab ("tcp: increase source port perturb table to
2^16").

Signed-off-by: Gleb Mazovetskiy <glex.spb@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/ipv4/Kconfig           | 10 ++++++++++
 net/ipv4/inet_hashtables.c | 10 +++++-----
 2 files changed, 15 insertions(+), 5 deletions(-)

diff --git a/net/ipv4/Kconfig b/net/ipv4/Kconfig
index 4abc4ba733bf..33f124a69f53 100644
--- a/net/ipv4/Kconfig
+++ b/net/ipv4/Kconfig
@@ -383,6 +383,16 @@ config INET_IPCOMP
 
 	  If unsure, say Y.
 
+config INET_TABLE_PERTURB_ORDER
+	int "INET: Source port perturbation table size (as power of 2)" if EXPERT
+	default 16
+	help
+	  Source port perturbation table size (as power of 2) for
+	  RFC 6056 3.3.4.  Algorithm 4: Double-Hash Port Selection Algorithm.
+
+	  The default is almost always what you want.
+	  Only change this if you know what you are doing.
+
 config INET_XFRM_TUNNEL
 	tristate
 	select INET_TUNNEL
diff --git a/net/ipv4/inet_hashtables.c b/net/ipv4/inet_hashtables.c
index 19369fc9bcda..48c7a3a51fc1 100644
--- a/net/ipv4/inet_hashtables.c
+++ b/net/ipv4/inet_hashtables.c
@@ -591,13 +591,13 @@ EXPORT_SYMBOL_GPL(inet_unhash);
  * Note that we use 32bit integers (vs RFC 'short integers')
  * because 2^16 is not a multiple of num_ephemeral and this
  * property might be used by clever attacker.
+ *
  * RFC claims using TABLE_LENGTH=10 buckets gives an improvement, though
- * attacks were since demonstrated, thus we use 65536 instead to really
- * give more isolation and privacy, at the expense of 256kB of kernel
- * memory.
+ * attacks were since demonstrated, thus we use 65536 by default instead
+ * to really give more isolation and privacy, at the expense of 256kB
+ * of kernel memory.
  */
-#define INET_TABLE_PERTURB_SHIFT 16
-#define INET_TABLE_PERTURB_SIZE (1 << INET_TABLE_PERTURB_SHIFT)
+#define INET_TABLE_PERTURB_SIZE (1 << CONFIG_INET_TABLE_PERTURB_ORDER)
 static u32 *table_perturb;
 
 int __inet_hash_connect(struct inet_timewait_death_row *death_row,
-- 
2.35.1

[PATCH AUTOSEL 4.14 08/10] dm-integrity: set dma_alignment limit in io_hints

[Sasha Levin]

From: Keith Busch <kbusch@kernel.org>

[ Upstream commit 29aa778bb66795e6a78b1c99beadc83887827868 ]

This device mapper needs bio vectors to be sized and memory aligned to
the logical block size. Set the minimum required queue limit
accordingly.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20221110184501.2451620-5-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/dm-integrity.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/md/dm-integrity.c b/drivers/md/dm-integrity.c
index 6579aa46f544..e7e44c1d5553 100644
--- a/drivers/md/dm-integrity.c
+++ b/drivers/md/dm-integrity.c
@@ -2297,6 +2297,7 @@ static void dm_integrity_io_hints(struct dm_target *ti, struct queue_limits *lim
 		limits->logical_block_size = ic->sectors_per_block << SECTOR_SHIFT;
 		limits->physical_block_size = ic->sectors_per_block << SECTOR_SHIFT;
 		blk_limits_io_min(limits, ic->sectors_per_block << SECTOR_SHIFT);
+		limits->dma_alignment = limits->logical_block_size - 1;
 	}
 }
 
-- 
2.35.1

[PATCH AUTOSEL 4.14 09/10] dm-log-writes: set dma_alignment limit in io_hints

[Sasha Levin]

From: Keith Busch <kbusch@kernel.org>

[ Upstream commit 50a893359cd2643ee1afc96eedc9e7084cab49fa ]

This device mapper needs bio vectors to be sized and memory aligned to
the logical block size. Set the minimum required queue limit
accordingly.

Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20221110184501.2451620-6-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/dm-log-writes.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/md/dm-log-writes.c b/drivers/md/dm-log-writes.c
index dafedbc28bcc..386148560734 100644
--- a/drivers/md/dm-log-writes.c
+++ b/drivers/md/dm-log-writes.c
@@ -809,6 +809,7 @@ static void log_writes_io_hints(struct dm_target *ti, struct queue_limits *limit
 	limits->logical_block_size = bdev_logical_block_size(lc->dev->bdev);
 	limits->physical_block_size = bdev_physical_block_size(lc->dev->bdev);
 	limits->io_min = limits->physical_block_size;
+	limits->dma_alignment = limits->logical_block_size - 1;
 }
 
 static struct target_type log_writes_target = {
-- 
2.35.1

[PATCH AUTOSEL 4.14 10/10] net: usb: qmi_wwan: add Telit 0x103a composition

[Sasha Levin]

From: Enrico Sau <enrico.sau@gmail.com>

[ Upstream commit e103ba33998d0f25653cc8ebe745b68d1ee10cda ]

Add the following Telit LE910C4-WWX composition:

0x103a: rmnet

Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20221115105859.14324-1-enrico.sau@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index 66c6b7111a3a..74040db959d8 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1306,6 +1306,7 @@ static const struct usb_device_id products[] = {
 	{QMI_FIXED_INTF(0x2357, 0x0201, 4)},	/* TP-LINK HSUPA Modem MA180 */
 	{QMI_FIXED_INTF(0x2357, 0x9000, 4)},	/* TP-LINK MA260 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1031, 3)}, /* Telit LE910C1-EUX */
+	{QMI_QUIRK_SET_DTR(0x1bc7, 0x103a, 0)}, /* Telit LE910C4-WWX */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1040, 2)},	/* Telit LE922A */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1050, 2)},	/* Telit FN980 */
 	{QMI_QUIRK_SET_DTR(0x1bc7, 0x1060, 2)},	/* Telit LN920 */
-- 
2.35.1