From: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
To: patrick@stwcx.xyz
Cc: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>,
Andrew Jeffery <andrew@codeconstruct.com.au>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org
Subject: [PATCH v18 0/3] Add i2c-mux and eeprom devices for Meta Yosemite4
Date: Mon, 9 Sep 2024 18:54:15 +0800 [thread overview]
Message-ID: <20240909105420.441607-1-Delphine_CC_Chiu@wiwynn.com> (raw)
From: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Changelog:
- v18
- Fix warnings for reg_format reporting by dts checking tool.
- v17
- Add SoB for the patches.
- v16
- Reorganized the patches.
- Add i2c-mux and resolve the dt-validate errors.
- Revise Yosemite 4 devicetree for devices behind i2c-mux.
- Add mctp config and sensors for NIC after i2c-mux on bus 15.
- Add fan led config for BMC to control according the status of fan.
- v15
- Add ISL28022 support
- v14
- Add SQ52205 support
- Add GPIO I6 pin
- v13
- Add RTQ6056-support-on-bus-11
- v12
- Fix GPIO linename typo and add missing GPIO pin initial state.
- v11
- Revise all GPIO line name with bottom line
- v10
- adjust mgm cpld ioexp bus
- add GPIOO7 name
- remove mctp driver
- v9
- add XDP710 support
- add RTQ6056 support
- add MP5990 support
- v8
- add fan led config
- v7
- Revise pca9506 i2c address
- v6
- Revise i2c duty-cycle for meeting 400khz spec
- v5
- Support medusa board adc sensors
- support NIC eeprom
- v4
- Re-format gpio linename
- Revise i2c device node names
- Split patches by logic changes
- v3
- Correct patch for revising gpio name
- v2
- Revise mx31790 fan tach config
- Add mctp config for NIC
- Support mux to cpld
- Revise gpio name
- v1
- Add gpio and eeprom behind i2c-mux
- Remove redundant idle-state setting for i2c-mux
- Enable adc 15, wdt2,spi gpio for yosemite4 use
- Revise quad mode to dual mode to avoid WP pin influnece the SPI
- Revise power sensor adm1281 for yosemite4 schematic change
- Add gpio pca9506 I/O expander for yosemite4 use
- remove space for adm1272 compatible
- enable interrupt setting for pca9555
- add eeprom for yosemite4 medusa board/BSM use
- remove temperature sensor for yosemite4 schematic change
- add power sensor for power module reading
- Revise adc128d818 adc mode for yosemite4 schematic change
- Revise ina233 for yosemite4 schematic change
- Remove idle state setting for yosemite4 NIC connection
- Initialize bmc gpio state
- Revise mx31790 fan tach config
- Add mctp config for NIC
- Support mux to cpld
- Revise gpio name
Ricky CX Wu (3):
ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
ARM: dts: aspeed: yosemite4: add mctp config and sensors for NIC
ARM: dts: aspeed: yosemite4: add fan led config
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 706 ++++++++++++++++--
1 file changed, 660 insertions(+), 46 deletions(-)
--
2.25.1
next reply other threads:[~2024-09-09 10:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-09-09 10:54 Delphine CC Chiu [this message]
2024-09-09 10:54 ` [PATCH v18 1/3] ARM: dts: aspeed: yosemite4: Revise i2c-mux devices Delphine CC Chiu
2024-09-09 10:54 ` [PATCH v18 2/3] ARM: dts: aspeed: yosemite4: add mctp config and sensors for NIC Delphine CC Chiu
2024-09-09 10:54 ` [PATCH v18 3/3] ARM: dts: aspeed: yosemite4: add fan led config Delphine CC Chiu
2024-09-09 15:45 ` [PATCH v18 0/3] Add i2c-mux and eeprom devices for Meta Yosemite4 Rob Herring (Arm)
2024-09-12 2:34 ` Andrew Jeffery
2024-09-20 6:38 ` Delphine_CC_Chiu/WYHQ/Wiwynn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240909105420.441607-1-Delphine_CC_Chiu@wiwynn.com \
--to=delphine_cc_chiu@wiwynn.com \
--cc=andrew@codeconstruct.com.au \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patrick@stwcx.xyz \
--cc=ricky.cx.wu.wiwynn@gmail.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox