[PATCH AUTOSEL 5.10 01/10] watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04

[PATCH AUTOSEL 5.10 01/10] watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04

[Sasha Levin]

From: James Hilliard <james.hilliard1@gmail.com>

[ Upstream commit 43439076383a7611300334d1357c0f8883f40816 ]

For the watchdog timer to work properly on the QCML04 board we need to
set PWRGD enable in the Environment Controller Configuration Registers
Special Configuration Register 1 when it is not already set, this may
be the case when the watchdog is not enabled from within the BIOS.

Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241025063441.3494837-1-james.hilliard1@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/watchdog/it87_wdt.c | 39 +++++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/watchdog/it87_wdt.c b/drivers/watchdog/it87_wdt.c
index 6340ca058f890..da9e24e4a8b60 100644
--- a/drivers/watchdog/it87_wdt.c
+++ b/drivers/watchdog/it87_wdt.c
@@ -20,6 +20,8 @@
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+#include <linux/bits.h>
+#include <linux/dmi.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
@@ -40,6 +42,7 @@
 #define VAL		0x2f
 
 /* Logical device Numbers LDN */
+#define EC		0x04
 #define GPIO		0x07
 
 /* Configuration Registers and Functions */
@@ -71,6 +74,12 @@
 #define IT8784_ID	0x8784
 #define IT8786_ID	0x8786
 
+/* Environment Controller Configuration Registers LDN=0x04 */
+#define SCR1		0xfa
+
+/* Environment Controller Bits SCR1 */
+#define WDT_PWRGD	0x20
+
 /* GPIO Configuration Registers LDN=0x07 */
 #define WDTCTRL		0x71
 #define WDTCFG		0x72
@@ -241,6 +250,21 @@ static int wdt_set_timeout(struct watchdog_device *wdd, unsigned int t)
 	return ret;
 }
 
+enum {
+	IT87_WDT_OUTPUT_THROUGH_PWRGD	= BIT(0),
+};
+
+static const struct dmi_system_id it87_quirks[] = {
+	{
+		/* Qotom Q30900P (IT8786) */
+		.matches = {
+			DMI_EXACT_MATCH(DMI_BOARD_NAME, "QCML04"),
+		},
+		.driver_data = (void *)IT87_WDT_OUTPUT_THROUGH_PWRGD,
+	},
+	{}
+};
+
 static const struct watchdog_info ident = {
 	.options = WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING,
 	.firmware_version = 1,
@@ -262,8 +286,10 @@ static struct watchdog_device wdt_dev = {
 
 static int __init it87_wdt_init(void)
 {
+	const struct dmi_system_id *dmi_id;
 	u8  chip_rev;
 	u8 ctrl;
+	int quirks = 0;
 	int rc;
 
 	rc = superio_enter();
@@ -274,6 +300,10 @@ static int __init it87_wdt_init(void)
 	chip_rev  = superio_inb(CHIPREV) & 0x0f;
 	superio_exit();
 
+	dmi_id = dmi_first_match(it87_quirks);
+	if (dmi_id)
+		quirks = (long)dmi_id->driver_data;
+
 	switch (chip_type) {
 	case IT8702_ID:
 		max_units = 255;
@@ -334,6 +364,15 @@ static int __init it87_wdt_init(void)
 		superio_outb(0x00, WDTCTRL);
 	}
 
+	if (quirks & IT87_WDT_OUTPUT_THROUGH_PWRGD) {
+		superio_select(EC);
+		ctrl = superio_inb(SCR1);
+		if (!(ctrl & WDT_PWRGD)) {
+			ctrl |= WDT_PWRGD;
+			superio_outb(ctrl, SCR1);
+		}
+	}
+
 	superio_exit();
 
 	if (timeout < 1 || timeout > max_units * 60) {
-- 
2.43.0

[PATCH AUTOSEL 5.10 02/10] scsi: qla1280: Fix hw revision numbering for ISP1020/1040

[Sasha Levin]

From: Magnus Lindholm <linmag7@gmail.com>

[ Upstream commit c064de86d2a3909222d5996c5047f64c7a8f791b ]

Fix the hardware revision numbering for Qlogic ISP1020/1040 boards.  HWMASK
suggests that the revision number only needs four bits, this is consistent
with how NetBSD does things in their ISP driver. Verified on a IPS1040B
which is seen as rev 5 not as BIT_4.

Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20241113225636.2276-1-linmag7@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla1280.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/scsi/qla1280.h b/drivers/scsi/qla1280.h
index e7820b5bca38c..c0a9251b2bed2 100644
--- a/drivers/scsi/qla1280.h
+++ b/drivers/scsi/qla1280.h
@@ -117,12 +117,12 @@ struct device_reg {
 	uint16_t id_h;		/* ID high */
 	uint16_t cfg_0;		/* Configuration 0 */
 #define ISP_CFG0_HWMSK   0x000f	/* Hardware revision mask */
-#define ISP_CFG0_1020    BIT_0	/* ISP1020 */
-#define ISP_CFG0_1020A	 BIT_1	/* ISP1020A */
-#define ISP_CFG0_1040	 BIT_2	/* ISP1040 */
-#define ISP_CFG0_1040A	 BIT_3	/* ISP1040A */
-#define ISP_CFG0_1040B	 BIT_4	/* ISP1040B */
-#define ISP_CFG0_1040C	 BIT_5	/* ISP1040C */
+#define ISP_CFG0_1020	 1	/* ISP1020 */
+#define ISP_CFG0_1020A	 2	/* ISP1020A */
+#define ISP_CFG0_1040	 3	/* ISP1040 */
+#define ISP_CFG0_1040A	 4	/* ISP1040A */
+#define ISP_CFG0_1040B	 5	/* ISP1040B */
+#define ISP_CFG0_1040C	 6	/* ISP1040C */
 	uint16_t cfg_1;		/* Configuration 1 */
 #define ISP_CFG1_F128    BIT_6  /* 128-byte FIFO threshold */
 #define ISP_CFG1_F64     BIT_4|BIT_5 /* 128-byte FIFO threshold */
-- 
2.43.0

[PATCH AUTOSEL 5.10 03/10] scsi: megaraid_sas: Fix for a potential deadlock

[Sasha Levin]

From: Tomas Henzl <thenzl@redhat.com>

[ Upstream commit 50740f4dc78b41dec7c8e39772619d5ba841ddd7 ]

This fixes a 'possible circular locking dependency detected' warning
      CPU0                    CPU1
      ----                    ----
 lock(&instance->reset_mutex);
                              lock(&shost->scan_mutex);
                              lock(&instance->reset_mutex);
 lock(&shost->scan_mutex);

Fix this by temporarily releasing the reset_mutex.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20240923174833.45345-1-thenzl@redhat.com
Acked-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/megaraid/megaraid_sas_base.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/megaraid/megaraid_sas_base.c b/drivers/scsi/megaraid/megaraid_sas_base.c
index 365279d7c9829..d709d261d0ad1 100644
--- a/drivers/scsi/megaraid/megaraid_sas_base.c
+++ b/drivers/scsi/megaraid/megaraid_sas_base.c
@@ -8868,8 +8868,11 @@ megasas_aen_polling(struct work_struct *work)
 						   (ld_target_id / MEGASAS_MAX_DEV_PER_CHANNEL),
 						   (ld_target_id - MEGASAS_MAX_DEV_PER_CHANNEL),
 						   0);
-			if (sdev1)
+			if (sdev1) {
+				mutex_unlock(&instance->reset_mutex);
 				megasas_remove_scsi_device(sdev1);
+				mutex_lock(&instance->reset_mutex);
+			}
 
 			event_type = SCAN_VD_CHANNEL;
 			break;
-- 
2.43.0

[PATCH AUTOSEL 5.10 04/10] ALSA: hda/conexant: fix Z60MR100 startup pop issue

[Sasha Levin]

From: bo liu <bo.liu@senarytech.com>

[ Upstream commit 947c4012f8f03a8bb946beb6e5294d5e32817d67 ]

When Z60MR100 startup, speaker will output a pop. To fix this issue,
we mute codec by init verbs in bios when system startup, and set GPIO
to low to unmute codec in codec driver when it loaded .

[ white space fixes and compile warning fix by tiwai ]

Signed-off-by: bo liu <bo.liu@senarytech.com>
Link: https://patch.msgid.link/20241129014441.437205-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/pci/hda/patch_conexant.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/sound/pci/hda/patch_conexant.c b/sound/pci/hda/patch_conexant.c
index 30025716164a0..40853b26a1c3f 100644
--- a/sound/pci/hda/patch_conexant.c
+++ b/sound/pci/hda/patch_conexant.c
@@ -238,6 +238,7 @@ enum {
 	CXT_FIXUP_HP_MIC_NO_PRESENCE,
 	CXT_PINCFG_SWS_JS201D,
 	CXT_PINCFG_TOP_SPEAKER,
+	CXT_FIXUP_HP_A_U,
 };
 
 /* for hda_fixup_thinkpad_acpi() */
@@ -705,6 +706,18 @@ static void cxt_setup_mute_led(struct hda_codec *codec,
 	}
 }
 
+static void cxt_setup_gpio_unmute(struct hda_codec *codec,
+				  unsigned int gpio_mute_mask)
+{
+	if (gpio_mute_mask) {
+		// set gpio data to 0.
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_DATA, 0);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_MASK, gpio_mute_mask);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_DIRECTION, gpio_mute_mask);
+		snd_hda_codec_write(codec, 0x01, 0, AC_VERB_SET_GPIO_STICKY_MASK, 0);
+	}
+}
+
 static void cxt_fixup_mute_led_gpio(struct hda_codec *codec,
 				const struct hda_fixup *fix, int action)
 {
@@ -719,6 +732,15 @@ static void cxt_fixup_hp_zbook_mute_led(struct hda_codec *codec,
 		cxt_setup_mute_led(codec, 0x10, 0x20);
 }
 
+static void cxt_fixup_hp_a_u(struct hda_codec *codec,
+			     const struct hda_fixup *fix, int action)
+{
+	// Init vers in BIOS mute the spk/hp by set gpio high to avoid pop noise,
+	// so need to unmute once by clearing the gpio data when runs into the system.
+	if (action == HDA_FIXUP_ACT_INIT)
+		cxt_setup_gpio_unmute(codec, 0x2);
+}
+
 /* ThinkPad X200 & co with cxt5051 */
 static const struct hda_pintbl cxt_pincfg_lenovo_x200[] = {
 	{ 0x16, 0x042140ff }, /* HP (seq# overridden) */
@@ -943,6 +965,10 @@ static const struct hda_fixup cxt_fixups[] = {
 		.type = HDA_FIXUP_FUNC,
 		.v.func = cxt_fixup_sirius_top_speaker,
 	},
+	[CXT_FIXUP_HP_A_U] = {
+		.type = HDA_FIXUP_FUNC,
+		.v.func = cxt_fixup_hp_a_u,
+	},
 };
 
 static const struct snd_pci_quirk cxt5045_fixups[] = {
@@ -1017,6 +1043,7 @@ static const struct snd_pci_quirk cxt5066_fixups[] = {
 	SND_PCI_QUIRK(0x103c, 0x8457, "HP Z2 G4 mini", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x8458, "HP Z2 G4 mini premium", CXT_FIXUP_HP_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1043, 0x138d, "Asus", CXT_FIXUP_HEADPHONE_MIC_PIN),
+	SND_PCI_QUIRK(0x14f1, 0x0252, "MBX-Z60MR100", CXT_FIXUP_HP_A_U),
 	SND_PCI_QUIRK(0x14f1, 0x0265, "SWS JS201D", CXT_PINCFG_SWS_JS201D),
 	SND_PCI_QUIRK(0x152d, 0x0833, "OLPC XO-1.5", CXT_FIXUP_OLPC_XO),
 	SND_PCI_QUIRK(0x17aa, 0x20f2, "Lenovo T400", CXT_PINCFG_LENOVO_TP410),
@@ -1062,6 +1089,7 @@ static const struct hda_model_fixup cxt5066_fixup_models[] = {
 	{ .id = CXT_PINCFG_LENOVO_NOTEBOOK, .name = "lenovo-20149" },
 	{ .id = CXT_PINCFG_SWS_JS201D, .name = "sws-js201d" },
 	{ .id = CXT_PINCFG_TOP_SPEAKER, .name = "sirius-top-speaker" },
+	{ .id = CXT_FIXUP_HP_A_U, .name = "HP-U-support" },
 	{}
 };
 
-- 
2.43.0

[PATCH AUTOSEL 5.10 05/10] regmap: Use correct format specifier for logging range errors

[Sasha Levin]

From: Mark Brown <broonie@kernel.org>

[ Upstream commit 3f1aa0c533d9dd8a835caf9a6824449c463ee7e2 ]

The register addresses are unsigned ints so we should use %u not %d to
log them.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20241127-regmap-test-high-addr-v1-1-74a48a9e0dc5@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/base/regmap/regmap.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/base/regmap/regmap.c b/drivers/base/regmap/regmap.c
index a3c4086603a60..7ce28ae9aa23e 100644
--- a/drivers/base/regmap/regmap.c
+++ b/drivers/base/regmap/regmap.c
@@ -1104,13 +1104,13 @@ struct regmap *__regmap_init(struct device *dev,
 
 		/* Sanity check */
 		if (range_cfg->range_max < range_cfg->range_min) {
-			dev_err(map->dev, "Invalid range %d: %d < %d\n", i,
+			dev_err(map->dev, "Invalid range %d: %u < %u\n", i,
 				range_cfg->range_max, range_cfg->range_min);
 			goto err_range;
 		}
 
 		if (range_cfg->range_max > map->max_register) {
-			dev_err(map->dev, "Invalid range %d: %d > %d\n", i,
+			dev_err(map->dev, "Invalid range %d: %u > %u\n", i,
 				range_cfg->range_max, map->max_register);
 			goto err_range;
 		}
-- 
2.43.0

[PATCH AUTOSEL 5.10 06/10] platform/x86: asus-nb-wmi: Ignore unknown event 0xCF

[Sasha Levin]

From: Armin Wolf <W_Armin@gmx.de>

[ Upstream commit e9fba20c29e27dc99e55e1c550573a114561bf8c ]

On the Asus X541UAK an unknown event 0xCF is emited when the charger
is plugged in. This is caused by the following AML code:

    If (ACPS ())
    {
        ACPF = One
        Local0 = 0x58
        If (ATKP)
        {
            ^^^^ATKD.IANE (0xCF)
        }
    }
    Else
    {
        ACPF = Zero
        Local0 = 0x57
    }

    Notify (AC0, 0x80) // Status Change
    If (ATKP)
    {
        ^^^^ATKD.IANE (Local0)
    }

    Sleep (0x64)
    PNOT ()
    Sleep (0x0A)
    NBAT (0x80)

Ignore the 0xCF event to silence the unknown event warning.

Reported-by: Pau Espin Pedrol <pespin@espeweb.net>
Closes: https://lore.kernel.org/platform-driver-x86/54d4860b-ec9c-4992-acf6-db3f90388293@espeweb.net
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241123224700.18530-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/asus-nb-wmi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/platform/x86/asus-nb-wmi.c b/drivers/platform/x86/asus-nb-wmi.c
index 49505939352ae..224c1f1c271bc 100644
--- a/drivers/platform/x86/asus-nb-wmi.c
+++ b/drivers/platform/x86/asus-nb-wmi.c
@@ -574,6 +574,7 @@ static const struct key_entry asus_nb_wmi_keymap[] = {
 	{ KE_KEY, 0xC4, { KEY_KBDILLUMUP } },
 	{ KE_KEY, 0xC5, { KEY_KBDILLUMDOWN } },
 	{ KE_IGNORE, 0xC6, },  /* Ambient Light Sensor notification */
+	{ KE_IGNORE, 0xCF, },	/* AC mode */
 	{ KE_KEY, 0xFA, { KEY_PROG2 } },           /* Lid flip action */
 	{ KE_KEY, 0xBD, { KEY_PROG2 } },           /* Lid flip action on ROG xflow laptops */
 	{ KE_END, 0},
-- 
2.43.0

[PATCH AUTOSEL 5.10 07/10] net: sched: fix ordering of qlen adjustment

[Sasha Levin]

From: Lion Ackermann <nnamrec@gmail.com>

[ Upstream commit 5eb7de8cd58e73851cd37ff8d0666517d9926948 ]

Changes to sch->q.qlen around qdisc_tree_reduce_backlog() need to happen
_before_ a call to said function because otherwise it may fail to notify
parent qdiscs when the child is about to become empty.

Signed-off-by: Lion Ackermann <nnamrec@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/sched/sch_cake.c  | 2 +-
 net/sched/sch_choke.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/sched/sch_cake.c b/net/sched/sch_cake.c
index 4ddb43a6644ab..8d9c0b98a747b 100644
--- a/net/sched/sch_cake.c
+++ b/net/sched/sch_cake.c
@@ -1541,7 +1541,6 @@ static unsigned int cake_drop(struct Qdisc *sch, struct sk_buff **to_free)
 	b->backlogs[idx]    -= len;
 	b->tin_backlog      -= len;
 	sch->qstats.backlog -= len;
-	qdisc_tree_reduce_backlog(sch, 1, len);
 
 	flow->dropped++;
 	b->tin_dropped++;
@@ -1552,6 +1551,7 @@ static unsigned int cake_drop(struct Qdisc *sch, struct sk_buff **to_free)
 
 	__qdisc_drop(skb, to_free);
 	sch->q.qlen--;
+	qdisc_tree_reduce_backlog(sch, 1, len);
 
 	cake_heapify(q, 0);
 
diff --git a/net/sched/sch_choke.c b/net/sched/sch_choke.c
index 25d2daaa81227..f3805bee995bb 100644
--- a/net/sched/sch_choke.c
+++ b/net/sched/sch_choke.c
@@ -124,10 +124,10 @@ static void choke_drop_by_idx(struct Qdisc *sch, unsigned int idx,
 	if (idx == q->tail)
 		choke_zap_tail_holes(q);
 
+	--sch->q.qlen;
 	qdisc_qstats_backlog_dec(sch, skb);
 	qdisc_tree_reduce_backlog(sch, 1, qdisc_pkt_len(skb));
 	qdisc_drop(skb, sch, to_free);
-	--sch->q.qlen;
 }
 
 struct choke_skb_cb {
-- 
2.43.0

[PATCH AUTOSEL 5.10 08/10] scsi: mpt3sas: Diag-Reset when Doorbell-In-Use bit is set during driver load time

[Sasha Levin]

From: Ranjan Kumar <ranjan.kumar@broadcom.com>

[ Upstream commit 3f5eb062e8aa335643181c480e6c590c6cedfd22 ]

Issue a Diag-Reset when the "Doorbell-In-Use" bit is set during the
driver load/initialization.

Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20241110173341.11595-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/mpt3sas/mpt3sas_base.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c
index 53528711dac1f..768635de93da9 100644
--- a/drivers/scsi/mpt3sas/mpt3sas_base.c
+++ b/drivers/scsi/mpt3sas/mpt3sas_base.c
@@ -6008,11 +6008,12 @@ _base_handshake_req_reply_wait(struct MPT3SAS_ADAPTER *ioc, int request_bytes,
 	int i;
 	u8 failed;
 	__le32 *mfp;
+	int ret_val;
 
 	/* make sure doorbell is not in use */
 	if ((ioc->base_readl_ext_retry(&ioc->chip->Doorbell) & MPI2_DOORBELL_USED)) {
 		ioc_err(ioc, "doorbell is in use (line=%d)\n", __LINE__);
-		return -EFAULT;
+		goto doorbell_diag_reset;
 	}
 
 	/* clear pending doorbell interrupts from previous state changes */
@@ -6102,6 +6103,10 @@ _base_handshake_req_reply_wait(struct MPT3SAS_ADAPTER *ioc, int request_bytes,
 			    le32_to_cpu(mfp[i]));
 	}
 	return 0;
+
+doorbell_diag_reset:
+	ret_val = _base_diag_reset(ioc);
+	return ret_val;
 }
 
 /**
-- 
2.43.0

[PATCH AUTOSEL 5.10 09/10] scsi: storvsc: Do not flag MAINTENANCE_IN return of SRB_STATUS_DATA_OVERRUN as an error

[Sasha Levin]

From: Cathy Avery <cavery@redhat.com>

[ Upstream commit b1aee7f034615b6824d2c70ddb37ef9fc23493b7 ]

This partially reverts commit 812fe6420a6e ("scsi: storvsc: Handle
additional SRB status values").

HyperV does not support MAINTENANCE_IN resulting in FC passthrough
returning the SRB_STATUS_DATA_OVERRUN value. Now that
SRB_STATUS_DATA_OVERRUN is treated as an error, multipath ALUA paths go
into a faulty state as multipath ALUA submits RTPG commands via
MAINTENANCE_IN.

[    3.215560] hv_storvsc 1d69d403-9692-4460-89f9-a8cbcc0f94f3:
tag#230 cmd 0xa3 status: scsi 0x0 srb 0x12 hv 0xc0000001
[    3.215572] scsi 1:0:0:32: alua: rtpg failed, result 458752

Make MAINTENANCE_IN return success to avoid the error path as is
currently done with INQUIRY and MODE_SENSE.

Suggested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Cathy Avery <cavery@redhat.com>
Link: https://lore.kernel.org/r/20241127181324.3318443-1-cavery@redhat.com
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/storvsc_drv.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index 37ad5f5256474..7dc916ce0c3c8 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -155,6 +155,8 @@ static int sense_buffer_size = PRE_WIN8_STORVSC_SENSE_BUFFER_SIZE;
 */
 static int vmstor_proto_version;
 
+static bool hv_dev_is_fc(struct hv_device *hv_dev);
+
 #define STORVSC_LOGGING_NONE	0
 #define STORVSC_LOGGING_ERROR	1
 #define STORVSC_LOGGING_WARN	2
@@ -1153,6 +1155,7 @@ static void storvsc_on_io_completion(struct storvsc_device *stor_device,
 	 * not correctly handle:
 	 * INQUIRY command with page code parameter set to 0x80
 	 * MODE_SENSE command with cmd[2] == 0x1c
+	 * MAINTENANCE_IN is not supported by HyperV FC passthrough
 	 *
 	 * Setup srb and scsi status so this won't be fatal.
 	 * We do this so we can distinguish truly fatal failues
@@ -1160,7 +1163,9 @@ static void storvsc_on_io_completion(struct storvsc_device *stor_device,
 	 */
 
 	if ((stor_pkt->vm_srb.cdb[0] == INQUIRY) ||
-	   (stor_pkt->vm_srb.cdb[0] == MODE_SENSE)) {
+	   (stor_pkt->vm_srb.cdb[0] == MODE_SENSE) ||
+	   (stor_pkt->vm_srb.cdb[0] == MAINTENANCE_IN &&
+	   hv_dev_is_fc(device))) {
 		vstor_packet->vm_srb.scsi_status = 0;
 		vstor_packet->vm_srb.srb_status = SRB_STATUS_SUCCESS;
 	}
-- 
2.43.0

[PATCH AUTOSEL 5.10 10/10] virtio-blk: don't keep queue frozen during system suspend

[Sasha Levin]

From: Ming Lei <ming.lei@redhat.com>

[ Upstream commit 7678abee0867e6b7fb89aa40f6e9f575f755fb37 ]

Commit 4ce6e2db00de ("virtio-blk: Ensure no requests in virtqueues before
deleting vqs.") replaces queue quiesce with queue freeze in virtio-blk's
PM callbacks. And the motivation is to drain inflight IOs before suspending.

block layer's queue freeze looks very handy, but it is also easy to cause
deadlock, such as, any attempt to call into bio_queue_enter() may run into
deadlock if the queue is frozen in current context. There are all kinds
of ->suspend() called in suspend context, so keeping queue frozen in the
whole suspend context isn't one good idea. And Marek reported lockdep
warning[1] caused by virtio-blk's freeze queue in virtblk_freeze().

[1] https://lore.kernel.org/linux-block/ca16370e-d646-4eee-b9cc-87277c89c43c@samsung.com/

Given the motivation is to drain in-flight IOs, it can be done by calling
freeze & unfreeze, meantime restore to previous behavior by keeping queue
quiesced during suspend.

Cc: Yi Sun <yi.sun@unisoc.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: virtualization@lists.linux.dev
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20241112125821.1475793-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/block/virtio_blk.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c
index 7eae3f3732336..28ea9b511fd0c 100644
--- a/drivers/block/virtio_blk.c
+++ b/drivers/block/virtio_blk.c
@@ -951,9 +951,12 @@ static void virtblk_remove(struct virtio_device *vdev)
 static int virtblk_freeze(struct virtio_device *vdev)
 {
 	struct virtio_blk *vblk = vdev->priv;
+	struct request_queue *q = vblk->disk->queue;
 
 	/* Ensure no requests in virtqueues before deleting vqs. */
-	blk_mq_freeze_queue(vblk->disk->queue);
+	blk_mq_freeze_queue(q);
+	blk_mq_quiesce_queue_nowait(q);
+	blk_mq_unfreeze_queue(q);
 
 	/* Ensure we don't receive any more interrupts */
 	vdev->config->reset(vdev);
@@ -977,8 +980,8 @@ static int virtblk_restore(struct virtio_device *vdev)
 		return ret;
 
 	virtio_device_ready(vdev);
+	blk_mq_unquiesce_queue(vblk->disk->queue);
 
-	blk_mq_unfreeze_queue(vblk->disk->queue);
 	return 0;
 }
 #endif
-- 
2.43.0