From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Andrew Halaney <ajhalaney@gmail.com>,
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>,
Sasha Levin <sashal@kernel.org>,
marcel@holtmann.org, luiz.dentz@gmail.com,
linux-bluetooth@vger.kernel.org
Subject: [PATCH AUTOSEL 6.13 25/35] Bluetooth: btusb: Add new VID/PID 13d3/3610 for MT7922
Date: Sun, 26 Jan 2025 10:00:19 -0500 [thread overview]
Message-ID: <20250126150029.953021-25-sashal@kernel.org> (raw)
In-Reply-To: <20250126150029.953021-1-sashal@kernel.org>
From: Andrew Halaney <ajhalaney@gmail.com>
[ Upstream commit 45e7d389bf2e52dfc893779c611dd5cff461b590 ]
A new machine has a Archer AX3000 / TX55e in it,
and out the box reported issues resetting hci0. It looks like
this is a MT7922 from the lspci output, so treat it as a MediaTek
device and use the proper callbacks. With that in place an xbox
controller can be used without issue as seen below:
[ 7.047388] Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[ 9.583883] Bluetooth: hci0: Device setup in 2582842 usecs
[ 9.583895] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 9.644780] Bluetooth: hci0: AOSP extensions version v1.00
[ 9.644784] Bluetooth: hci0: AOSP quality report is supported
[ 876.379876] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input27
[ 876.380215] hid-generic 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7
[ 876.429368] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input28
[ 876.429423] microsoft 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7
lspci output:
root@livingroom:/home/ajhalaney/git# lspci
...
05:00.0 Network controller: MEDIATEK Corp. MT7922 802.11ax PCI Express Wireless Network Adapter
and USB device:
root@livingroom:/home/ajhalaney/git# cat /sys/kernel/debug/usb/devices
...
T: Bus=01 Lev=01 Prnt=01 Port=10 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3610 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Andrew Halaney <ajhalaney@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/bluetooth/btusb.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 20ba8ceff7d1b..74f86c7f741bf 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -612,6 +612,8 @@ static const struct usb_device_id quirks_table[] = {
/* MediaTek MT7922 Bluetooth devices */
{ USB_DEVICE(0x13d3, 0x3585), .driver_info = BTUSB_MEDIATEK |
BTUSB_WIDEBAND_SPEECH },
+ { USB_DEVICE(0x13d3, 0x3610), .driver_info = BTUSB_MEDIATEK |
+ BTUSB_WIDEBAND_SPEECH },
/* MediaTek MT7922A Bluetooth devices */
{ USB_DEVICE(0x0489, 0xe0d8), .driver_info = BTUSB_MEDIATEK |
--
2.39.5
next prev parent reply other threads:[~2025-01-26 15:01 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-01-26 14:59 [PATCH AUTOSEL 6.13 01/35] wifi: ath12k: Fix for out-of bound access error Sasha Levin
2025-01-26 14:59 ` [PATCH AUTOSEL 6.13 02/35] wifi: ath12k: ath12k_mac_op_set_key(): fix uninitialized symbol 'ret' Sasha Levin
2025-01-26 14:59 ` [PATCH AUTOSEL 6.13 03/35] wifi: rtw89: add crystal_cap check to avoid setting as overflow value Sasha Levin
2025-01-26 14:59 ` [PATCH AUTOSEL 6.13 04/35] tun: fix group permission check Sasha Levin
2025-01-26 14:59 ` [PATCH AUTOSEL 6.13 05/35] mmc: core: Respect quirk_max_rate for non-UHS SDIO card Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 06/35] mmc: sdhci-esdhc-imx: enable 'SDHCI_QUIRK_NO_LED' quirk for S32G Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 07/35] Revert "HID: multitouch: Add support for lenovo Y9000P Touchpad" Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 08/35] wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy() Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 09/35] tomoyo: don't emit warning in tomoyo_write_control() Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 10/35] mfd: lpc_ich: Add another Gemini Lake ISA bridge PCI device-id Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 11/35] wifi: rtw88: add __packed attribute to efuse layout struct Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 12/35] clk: qcom: Make GCC_8150 depend on QCOM_GDSC Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 13/35] net/mlx5: HWS, change error flow on matcher disconnect Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 14/35] net/mlx5: HWS, num_of_rules counter on matcher should be atomic Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 15/35] HID: multitouch: Add quirk for Hantick 5288 touchpad Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 16/35] HID: Wacom: Add PCI Wacom device support Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 17/35] net/mlx5: use do_aux_work for PHC overflow checks Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 18/35] Revert "mfd: axp20x: Allow multiple regulators" Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 19/35] wifi: brcmfmac: Check the return value of of_property_read_string_index() Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 20/35] wifi: iwlwifi: pcie: Add support for new device ids Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 21/35] wifi: iwlwifi: avoid memory leak Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 22/35] i2c: Force ELAN06FA touchpad I2C bus freq to 100KHz Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 23/35] APEI: GHES: Have GHES honor the panic= setting Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 24/35] Bluetooth: btusb: Add ID 0x2c7c:0x0130 for Qualcomm WCN785x Sasha Levin
2025-01-26 15:00 ` Sasha Levin [this message]
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 26/35] Bluetooth: btusb: Add new VID/PID 13d3/3628 for MT7925 Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 27/35] Bluetooth: MGMT: Fix slab-use-after-free Read in mgmt_remove_adv_monitor_sync Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 28/35] net: wwan: iosm: Fix hibernation by re-binding the driver around it Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 29/35] HID: hid-asus: Disable OOBE mode on the ProArt P16 Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 30/35] mmc: sdhci-msm: Correctly set the load for the regulator Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 31/35] octeon_ep: update tx/rx stats locally for persistence Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 32/35] octeon_ep_vf: " Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 33/35] tipc: re-order conditions in tipc_crypto_key_rcv() Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 34/35] selftests/net/ipsec: Fix Null pointer dereference in rtattr_pack() Sasha Levin
2025-01-26 15:00 ` [PATCH AUTOSEL 6.13 35/35] net: ethernet: ti: am65-cpsw: ensure proper channel cleanup in error path Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250126150029.953021-25-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=ajhalaney@gmail.com \
--cc=linux-bluetooth@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luiz.dentz@gmail.com \
--cc=luiz.von.dentz@intel.com \
--cc=marcel@holtmann.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox