From: Maxime Chevallier <maxime.chevallier@bootlin.com>
To: davem@davemloft.net, Andrew Lunn <andrew@lunn.ch>,
Jakub Kicinski <kuba@kernel.org>,
Eric Dumazet <edumazet@google.com>,
Paolo Abeni <pabeni@redhat.com>,
Russell King <linux@armlinux.org.uk>,
Heiner Kallweit <hkallweit1@gmail.com>
Cc: "Maxime Chevallier" <maxime.chevallier@bootlin.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
thomas.petazzoni@bootlin.com,
linux-arm-kernel@lists.infradead.org,
"Christophe Leroy" <christophe.leroy@csgroup.eu>,
"Herve Codina" <herve.codina@bootlin.com>,
"Florian Fainelli" <f.fainelli@gmail.com>,
"Vladimir Oltean" <vladimir.oltean@nxp.com>,
"Köry Maincent" <kory.maincent@bootlin.com>,
"Oleksij Rempel" <o.rempel@pengutronix.de>,
"Simon Horman" <horms@kernel.org>,
"Romain Gantois" <romain.gantois@bootlin.com>
Subject: [PATCH net-next v3 07/13] net: phy: phy_caps: Allow looking-up link caps based on speed and duplex
Date: Fri, 28 Feb 2025 15:55:32 +0100 [thread overview]
Message-ID: <20250228145540.2209551-8-maxime.chevallier@bootlin.com> (raw)
In-Reply-To: <20250228145540.2209551-1-maxime.chevallier@bootlin.com>
As the link_caps array is efficient for <speed,duplex> lookups,
implement a function for speed/duplex lookups that matches a given
mask. This replicates to some extent the phy_lookup_settings()
behaviour, matching full link_capabilities instead of a single linkmode.
phy.c's phy_santize_settings() and phylink's
phylink_ethtool_ksettings_set() performs such lookup using the
phy_settings table, but are only interested in the actual speed/duplex
that were matched, rathet than the individual linkmode.
Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup()
will run through the link_caps[] array by descending speed/duplex order.
If the link_capabilities for a given <speed/duplex> tuple intersects the
passed linkmodes, we consider that a match.
Similar to phy_lookup_settings(), we also allow passing an 'exact'
boolean, allowing non-exact match. Here, we MUST always match the
linkmodes mask, but we allow matching on lower speed settings.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
drivers/net/phy/phy-caps.h | 4 ++++
drivers/net/phy/phy.c | 32 ++++++-------------------
drivers/net/phy/phy_caps.c | 49 ++++++++++++++++++++++++++++++++++++++
drivers/net/phy/phylink.c | 17 ++++++-------
4 files changed, 69 insertions(+), 33 deletions(-)
diff --git a/drivers/net/phy/phy-caps.h b/drivers/net/phy/phy-caps.h
index 7b95a9cb5ebb..dd3ea9f77f1c 100644
--- a/drivers/net/phy/phy-caps.h
+++ b/drivers/net/phy/phy-caps.h
@@ -52,4 +52,8 @@ phy_caps_lookup_by_linkmode(const unsigned long *linkmodes);
const struct link_capabilities *
phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only);
+const struct link_capabilities *
+phy_caps_lookup(int speed, unsigned int duplex, const unsigned long *supported,
+ bool exact);
+
#endif /* __PHY_CAPS_H */
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 8df37d221fba..562acde89224 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -213,25 +213,6 @@ int phy_aneg_done(struct phy_device *phydev)
}
EXPORT_SYMBOL(phy_aneg_done);
-/**
- * phy_find_valid - find a PHY setting that matches the requested parameters
- * @speed: desired speed
- * @duplex: desired duplex
- * @supported: mask of supported link modes
- *
- * Locate a supported phy setting that is, in priority order:
- * - an exact match for the specified speed and duplex mode
- * - a match for the specified speed, or slower speed
- * - the slowest supported speed
- * Returns the matched phy_setting entry, or %NULL if no supported phy
- * settings were found.
- */
-static const struct phy_setting *
-phy_find_valid(int speed, int duplex, unsigned long *supported)
-{
- return phy_lookup_setting(speed, duplex, supported, false);
-}
-
/**
* phy_supported_speeds - return all speeds currently supported by a phy device
* @phy: The phy device to return supported speeds of.
@@ -274,13 +255,14 @@ EXPORT_SYMBOL(phy_check_valid);
*/
static void phy_sanitize_settings(struct phy_device *phydev)
{
- const struct phy_setting *setting;
+ const struct link_capabilities *c;
+
+ c = phy_caps_lookup(phydev->speed, phydev->duplex, phydev->supported,
+ false);
- setting = phy_find_valid(phydev->speed, phydev->duplex,
- phydev->supported);
- if (setting) {
- phydev->speed = setting->speed;
- phydev->duplex = setting->duplex;
+ if (c) {
+ phydev->speed = c->speed;
+ phydev->duplex = c->duplex;
} else {
/* We failed to find anything (no supported speeds?) */
phydev->speed = SPEED_UNKNOWN;
diff --git a/drivers/net/phy/phy_caps.c b/drivers/net/phy/phy_caps.c
index 8cf7ff3f1368..77bf85043e82 100644
--- a/drivers/net/phy/phy_caps.c
+++ b/drivers/net/phy/phy_caps.c
@@ -149,6 +149,55 @@ phy_caps_lookup_by_linkmode_rev(const unsigned long *linkmodes, bool fdx_only)
return NULL;
}
+/**
+ * phy_caps_lookup() - Lookup capabilities by speed/duplex that matches a mask
+ * @speed: Speed to match
+ * @duplex: Duplex to match
+ * @supported: Mask of linkmodes to match
+ * @exact: Perform an exact match or not.
+ *
+ * Lookup a link_capabilities entry that intersect the supported linkmodes mask,
+ * and that matches the passed speed and duplex.
+ *
+ * When @exact is set, an exact match is performed on speed and duplex, meaning
+ * that if the linkmodes for the given speed and duplex intersect the supported
+ * mask, this capability is returned, otherwise we don't have a match and return
+ * NULL.
+ *
+ * When @exact is not set, we return either an exact match, or matching capabilities
+ * at lower speed, or the lowest matching speed, or NULL.
+ *
+ * Returns: a matched link_capabilities according to the above process, NULL
+ * otherwise.
+ */
+const struct link_capabilities *
+phy_caps_lookup(int speed, unsigned int duplex, const unsigned long *supported,
+ bool exact)
+{
+ const struct link_capabilities *c, *last = NULL;
+ int capa;
+
+ for (capa = __LINK_CAPA_LAST; capa >= 0; capa--) {
+ c = &link_caps[capa];
+ if (linkmode_intersects(c->linkmodes, supported)) {
+ last = c;
+ /* exact match on speed and duplex*/
+ if (c->speed == speed && c->duplex == duplex) {
+ return c;
+ } else if (!exact) {
+ if (c->speed <= speed)
+ return c;
+ }
+ }
+ }
+
+ if (!exact)
+ return last;
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(phy_caps_lookup);
+
/**
* phy_caps_linkmode_max_speed() - Clamp a linkmodes set to a max speed
* @max_speed: Speed limit for the linkmode set
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index a3b186ab3854..6c67d5c9b787 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -20,6 +20,7 @@
#include <linux/timer.h>
#include <linux/workqueue.h>
+#include "phy-caps.h"
#include "sfp.h"
#include "swphy.h"
@@ -2852,8 +2853,8 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
const struct ethtool_link_ksettings *kset)
{
__ETHTOOL_DECLARE_LINK_MODE_MASK(support);
+ const struct link_capabilities *c;
struct phylink_link_state config;
- const struct phy_setting *s;
ASSERT_RTNL();
@@ -2896,23 +2897,23 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
/* Autonegotiation disabled, select a suitable speed and
* duplex.
*/
- s = phy_lookup_setting(kset->base.speed, kset->base.duplex,
- pl->supported, false);
- if (!s)
+ c = phy_caps_lookup(kset->base.speed, kset->base.duplex,
+ pl->supported, false);
+ if (!c)
return -EINVAL;
/* If we have a fixed link, refuse to change link parameters.
* If the link parameters match, accept them but do nothing.
*/
if (pl->req_link_an_mode == MLO_AN_FIXED) {
- if (s->speed != pl->link_config.speed ||
- s->duplex != pl->link_config.duplex)
+ if (c->speed != pl->link_config.speed ||
+ c->duplex != pl->link_config.duplex)
return -EINVAL;
return 0;
}
- config.speed = s->speed;
- config.duplex = s->duplex;
+ config.speed = c->speed;
+ config.duplex = c->duplex;
break;
case AUTONEG_ENABLE:
--
2.48.1
next prev parent reply other threads:[~2025-02-28 14:55 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-02-28 14:55 [PATCH net-next v3 00/13] net: phy: Rework linkmodes handling in a dedicated file Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 01/13] net: ethtool: Export the link_mode_params definitions Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 02/13] net: phy: Use an internal, searchable storage for the linkmodes Maxime Chevallier
2025-02-28 15:41 ` Russell King (Oracle)
2025-02-28 15:55 ` Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 03/13] net: phy: phy_caps: Move phy_speeds to phy_caps Maxime Chevallier
2025-02-28 16:10 ` Russell King (Oracle)
2025-02-28 16:17 ` Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 04/13] net: phy: phy_caps: Move __set_linkmode_max_speed " Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 05/13] net: phy: phy_caps: Introduce phy_caps_valid Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 06/13] net: phy: phy_caps: Implement link_capabilities lookup by linkmode Maxime Chevallier
2025-02-28 14:55 ` Maxime Chevallier [this message]
2025-02-28 14:55 ` [PATCH net-next v3 08/13] net: phy: phy_device: Use link_capabilities lookup for PHY aneg config Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 09/13] net: phylink: Use phy_caps_lookup for fixed-link configuration Maxime Chevallier
2025-02-28 16:20 ` Russell King (Oracle)
2025-02-28 16:49 ` Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 10/13] net: phy: drop phy_settings and the associated lookup helpers Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 11/13] net: phylink: Add a mapping between MAC_CAPS and LINK_CAPS Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 12/13] net: phylink: Convert capabilities to linkmodes using phy_caps Maxime Chevallier
2025-02-28 14:55 ` [PATCH net-next v3 13/13] net: phy: phy_caps: Allow getting an phy_interface's capabilities Maxime Chevallier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250228145540.2209551-8-maxime.chevallier@bootlin.com \
--to=maxime.chevallier@bootlin.com \
--cc=andrew@lunn.ch \
--cc=christophe.leroy@csgroup.eu \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=f.fainelli@gmail.com \
--cc=herve.codina@bootlin.com \
--cc=hkallweit1@gmail.com \
--cc=horms@kernel.org \
--cc=kory.maincent@bootlin.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=netdev@vger.kernel.org \
--cc=o.rempel@pengutronix.de \
--cc=pabeni@redhat.com \
--cc=romain.gantois@bootlin.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=vladimir.oltean@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox