[PATCH net-next v3 0/2] Add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

[PATCH net-next v3 0/2] Add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

[Artem Shimko]

Hello,

This series adds support for the DAPU Telecom DAP8211R(I) Gigabit
Ethernet PHY, commonly used in enterprise and industrial networking
applications. The PHY supports 10/100/1000 Mbps operation with RGMII
interface and includes features such as IEEE 802.3az Energy Efficient
Ethernet, IEEE 1588 SyncE, and an internal packet generator for
diagnostics.

The driver implements extended register access via indirect addressing
(registers 0x1E/0x1F) and provides comprehensive device tree support
for RGMII delay configuration. The rx-internal-delay-ps and
tx-internal-delay-ps properties allow precise tuning of clock delays
in 150 ps steps from 0 to 2250 ps. The optional dapu,tx-inverted-clk
flag enables 180-degree TX clock phase shift for boards where signal
integrity or MAC requirements necessitate clock inversion.

This PHY is used on the NDA platform with 1G Ethernet tile and has
been tested on that hardware with successful link establishment and
RGMII delay tuning.

Due to the specific PCB layout of the platform and FPGA configuration,
the default RGMII timing configuration was insufficient, causing packet
loss during normal operation. Tuning the TX/RX line delays and enabling
clock inversion restored proper signal timing, resulting in zero packet
loss and stable link performance.

$ make dt_binding_check DT_SCHEMA_FILES=dapu,dap8211r.yaml
  SCHEMA  Documentation/devicetree/bindings/processed-schema.json
  CHKDT   ./Documentation/devicetree/bindings
  LINT    ./Documentation/devicetree/bindings
  STYLE   ./Documentation/devicetree/bindings
  DTEX    Documentation/devicetree/bindings/net/dapu,dap8211r.example.dts
  DTC [C] Documentation/devicetree/bindings/net/dapu,dap8211r.example.dtb

grep -i "dap8211r" Documentation/devicetree/bindings/processed-schema.json
chema.json
    "http://devicetree.org/schemas/net/dapu,dap8211r.yaml": {
        "$filename": ".../devicetree/bindings/net/dapu,dap8211r.yaml",
        "$id": "http://devicetree.org/schemas/net/dapu,dap8211r.yaml#",
        "title": "DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY",

Working with xgmac.

Board side:

$ arping -I eth0 192.168.5.100
ARPING 192.168.5.1 from 192.168.5.100 eth0
Unicast reply from 192.168.5.1 [board.mac.addr]  8.543ms
Unicast reply from 192.168.5.1 [board.mac.addr]  3.295ms
Unicast reply from 192.168.5.1 [board.mac.addr]  4.301ms
Unicast reply from 192.168.5.1 [board.mac.addr]  4.096ms
Unicast reply from 192.168.5.1 [board.mac.addr]  2.872ms
...

$ Unfortunately, there is a dependence on the axibus speed here
$ iperf3 -c 192.168.5.1
Connecting to host 192.168.5.1, port 5201
[  5] local 192.168.5.100 port 58936 connected to 192.168.5.1 port 5201
[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
[  5]   0.00-1.00   sec  7.88 MBytes  65.8 Mbits/sec    0    150 KBytes
[  5]   1.00-2.00   sec  8.50 MBytes  71.4 Mbits/sec    0    165 KBytes
[  5]   2.00-3.00   sec  8.25 MBytes  69.2 Mbits/sec    0    165 KBytes
[  5]   3.00-4.01   sec  8.50 MBytes  71.1 Mbits/sec    0    165 KBytes
[  5]   4.01-5.00   sec  8.38 MBytes  70.3 Mbits/sec    0    165 KBytes
[  5]   5.00-6.00   sec  8.50 MBytes  71.5 Mbits/sec    0    165 KBytes
[  5]   6.00-7.01   sec  8.62 MBytes  72.0 Mbits/sec    0    174 KBytes
[  5]   7.01-8.00   sec  8.62 MBytes  72.8 Mbits/sec    0    174 KBytes
[  5]   8.00-9.00   sec  8.62 MBytes  72.2 Mbits/sec    0    174 KBytes
[  5]   9.00-10.04  sec  8.62 MBytes  69.9 Mbits/sec    0    174 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.04  sec  84.6 MBytes  70.7 Mbits/sec    0 sender
[  5]   0.00-10.12  sec  84.8 MBytes  70.3 Mbits/sec receiveriperf Done.

$ ethtool -t eth0
...
The test extra info:
 1. MAC Loopback                 0
 2. MAC Loopback (diff. queues)  0
 3. PHY Loopback                 0
...

ELP side:
...
17:29:11.974973 ARP, Reply ELP is-at elp.mac.addr(oui Unknown), length 28
17:29:12.975199 ARP, Request who-has ELP tell 192.168.5.100, length 46
17:29:12.975217 ARP, Reply ELP is-at elp.mac.addr(oui Unknown), length 28
17:29:13.975022 ARP, Request who-has ELP tell 192.168.5.100, length 46
17:29:13.975035 ARP, Reply ELP is-at elp.mac.addr(oui Unknown), length 28
17:29:14.974837 ARP, Request who-has ELP tell 192.168.5.100, length 46
17:29:14.974849 ARP, Reply ELP is-at elp.mac.addr(oui Unknown), length 28
17:29:15.975026 ARP, Request who-has ELP tell 192.168.5.100, length 46
...

Accepted connection from 192.168.5.100, port 58932
[  5] local 192.168.5.1 port 5201 connected to 192.168.5.100 port 58936
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  7.12 MBytes  59.7 Mbits/sec
[  5]   1.00-2.00   sec  8.50 MBytes  71.3 Mbits/sec
[  5]   2.00-3.00   sec  8.50 MBytes  71.3 Mbits/sec
[  5]   3.00-4.00   sec  8.38 MBytes  70.3 Mbits/sec
[  5]   4.00-5.00   sec  8.50 MBytes  71.3 Mbits/sec
[  5]   5.00-6.00   sec  8.38 MBytes  70.3 Mbits/sec
[  5]   6.00-7.00   sec  8.62 MBytes  72.4 Mbits/sec
[  5]   7.00-8.00   sec  8.62 MBytes  72.3 Mbits/sec
[  5]   8.00-9.00   sec  8.62 MBytes  72.4 Mbits/sec
[  5]   9.00-10.00  sec  8.62 MBytes  72.4 Mbits/sec
[  5]  10.00-10.12  sec   896 KBytes  62.3 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.12  sec  84.8 MBytes  70.3 Mbits/sec receiver

DTS node example:
&ethernet_1g_tile {
  ...
  phy-mode = "rgmii-rxid";
  phy-handle = <&phy1>;
  ...

  mdio: mdio {
    phy1: ethernet-phy@1 {
      ...
      compatible = "ethernet-phy-id0008.011b";
      rx-internal-delay-ps = <1050>;
      dapu,tx-inverted-clk;
      ...
    };
  };
};

--
Best regards,
Artem Shimko

ChangeLog:
  v3:
    - Use phy_get_internal_delay() for delay validation and selection
    - Add poll timeout for reset using read_poll_timeout()
  v2:
    - https://lore.kernel.org/all/20260716113805.593215-1-a.shimko.dev@gmail.com/T/#t
  v1:
    - https://lore.kernel.org/all/20260713131223.279555-1-a.shimko.dev@gmail.com/T/#t

Artem Shimko (2):
  dt-bindings: net: add DAPU Telecom DAP8211R(I) PHY binding
  net: phy: add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

 .../bindings/net/dapu,dap8211r.yaml           |  73 +++++++
 drivers/net/phy/Kconfig                       |  10 +
 drivers/net/phy/Makefile                      |   1 +
 drivers/net/phy/dap8211r.c                    | 191 ++++++++++++++++++
 4 files changed, 275 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dapu,dap8211r.yaml
 create mode 100644 drivers/net/phy/dap8211r.c

-- 
2.43.0

[PATCH net-next v3 1/2] dt-bindings: net: add DAPU Telecom DAP8211R(I) PHY binding

[Artem Shimko]

Add device tree binding documentation for the DAPU Telecom DAP8211R(I)
Gigabit Ethernet PHY.

The PHY supports TX and RX clock delays in 150 ps steps from 0 to 2250 ps,
with a default of 1950 ps if not specified. The dapu,tx-inverted-clk flag
provides a vendor-specific extension for boards where PCB trace length or
MAC requirements necessitate 180-degree clock phase shift.

Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
---
 .../bindings/net/dapu,dap8211r.yaml           | 73 +++++++++++++++++++
 1 file changed, 73 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/dapu,dap8211r.yaml

diff --git a/Documentation/devicetree/bindings/net/dapu,dap8211r.yaml b/Documentation/devicetree/bindings/net/dapu,dap8211r.yaml
new file mode 100644
index 000000000000..d4012fa17a1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dapu,dap8211r.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dapu,dap8211r.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY
+
+maintainers:
+  - Artem Shimko <a.shimko.dev@gmail.com>
+
+description: |
+  The DAP8211R(I) is a Gigabit Ethernet PHY with RGMII interface,
+  supporting IEEE 802.3az Energy Efficient Ethernet, IEEE 1588 SyncE,
+  and an internal packet generator for diagnostics.
+
+  Specifications:
+    - 10BASE-Te, 100BASE-TX, 1000BASE-T
+    - RGMII with configurable TX/RX clock delays (150 ps steps, 0-2250 ps)
+    - IEEE 802.3az-2010 Energy Efficient Ethernet
+    - IEEE 1588 SyncE support
+    - Internal packet generator and checker for link diagnostics
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  compatible:
+    const: ethernet-phy-id0008.011b
+
+  reg:
+    maxItems: 1
+
+  rx-internal-delay-ps:
+    description:
+      RGMII RX clock delay in picoseconds (0 to maximum).
+    multipleOf: 150
+    maximum: 2250
+    default: 1950
+
+  tx-internal-delay-ps:
+    description:
+      RGMII TX clock delay in picoseconds (0 to maximum).
+    multipleOf: 150
+    maximum: 2250
+    default: 1950
+
+  dapu,tx-inverted-clk:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If present, the RGMII TX clock to the MAC is inverted (180 degree
+      phase shift relative to the data lines). This is a vendor-specific
+      extension for boards where PCB trace length or MAC requirements
+      necessitate clock inversion. Only use this property after hardware
+      signal integrity validation.
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-phy@1 {
+            compatible = "ethernet-phy-id0008.011b";
+            reg = <1>;
+            rx-internal-delay-ps = <2100>;
+            tx-internal-delay-ps = <2100>;
+            dapu,tx-inverted-clk;
+        };
+    };
+
-- 
2.43.0

[PATCH net-next v3 2/2] net: phy: add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

[Artem Shimko]

Add a new PHY driver for the DAPU Telecom DAP8211R(I) Gigabit
Ethernet PHY, which is commonly used in enterprise and industrial
networking applications.

The driver implements extended register access via indirect addressing
through corresponding registers, and provides comprehensive device tree
support for RGMII delay configuration. The rx-internal-delay-ps and
tx-internal-delay-ps properties allow precise tuning of clock delays in
150 ps steps from 0 to 2250 ps. Additionally, the optional
dapu,tx-inverted-clk flag enables 180-degree TX clock phase shift for
boards where signal integrity or MAC requirements necessitate clock
inversion.

Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
---
 drivers/net/phy/Kconfig    |  10 ++
 drivers/net/phy/Makefile   |   1 +
 drivers/net/phy/dap8211r.c | 191 +++++++++++++++++++++++++++++++++++++
 3 files changed, 202 insertions(+)
 create mode 100644 drivers/net/phy/dap8211r.c

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 099f25dceabb..4576f707ac94 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -237,6 +237,16 @@ config DAVICOM_PHY
 	help
 	  Currently supports dm9161e and dm9131
 
+config DAP8211R_PHY
+	tristate "DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY"
+	depends on OF
+	help
+	  Support for the DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY.
+	  This PHY is designed for enterprise and industrial networking
+	  applications, supporting 10/100/1000 Mbps operation.
+	  RGMII with: configurable TX/RX clock delays, optional flag to enable
+	  180-degree TX clock phase shift and internal packet generator.
+
 config ICPLUS_PHY
 	tristate "ICPlus PHYs"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index de660ae94945..ad35733eb4bb 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
 obj-$(CONFIG_CICADA_PHY)	+= cicada.o
 obj-$(CONFIG_CORTINA_PHY)	+= cortina.o
 obj-$(CONFIG_DAVICOM_PHY)	+= davicom.o
+obj-$(CONFIG_DAP8211R_PHY)	+= dap8211r.o
 obj-$(CONFIG_DP83640_PHY)	+= dp83640.o
 obj-$(CONFIG_DP83822_PHY)	+= dp83822.o
 obj-$(CONFIG_DP83848_PHY)	+= dp83848.o
diff --git a/drivers/net/phy/dap8211r.c b/drivers/net/phy/dap8211r.c
new file mode 100644
index 000000000000..e6381fd8c98c
--- /dev/null
+++ b/drivers/net/phy/dap8211r.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL
+/*
+ * Driver for the DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY.
+ *
+ * Specifications:
+ *   - IEEE 802.3 10BASE-Te, 100BASE-TX, 1000BASE-T
+ *   - IEEE 802.3az-2010 Energy Efficient Ethernet
+ *   - IEEE 1588 SyncE support
+ *   - RGMII
+ *
+ * Author: Artem Shimko <a.shimko.dev@gmail.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/errno.h>
+#include <linux/ethtool.h>
+#include <linux/kernel.h>
+#include <linux/iopoll.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+
+#define DAP8211R_PHY_ID			0x0008011B
+#define DAP8211R_PHY_ID_MASK		0xFFFFFFFF
+
+#define DAP8211R_EXT_ADD		0x1E
+#define DAP8211R_EXT_DATA		0x1F
+
+#define DAP8211R_PHY_CON		0xA001
+#define DAP8211R_PHY_SW_RST		BIT(15)
+
+#define DAP8211R_RGMII_CON		0xA003
+/* Default initial TX delay value by datasheet. */
+#define DAP8211R_INIT_TX_DEL_VAL	1
+#define DAP8211R_RGMII_TX_DEL_MASK	GENMASK(3, 0)
+#define DAP8211R_RGMII_RX_DEL_MASK	GENMASK(13, 10)
+#define DAP8211R_RGMII_CLK_INVERT	BIT(14)
+
+#define DAP8211R_RGMII_CONFIG_MASK	(DAP8211R_RGMII_CLK_INVERT | \
+					DAP8211R_RGMII_RX_DEL_MASK | \
+					DAP8211R_RGMII_TX_DEL_MASK)
+
+/* Default RGMII delay: 13 * 150 == 1.95ns */
+#define DAP8211R_DEFAULT_DEL_SEL	0xD
+
+static const int dap8211r_internal_delay[] = {0, 150, 300, 450, 600, 750, 900,
+					      1050, 1200, 1350, 1500, 1650, 1800,
+					      1950, 2100, 2250};
+
+#define DAP8211R_DELAY_SIZE	ARRAY_SIZE(dap8211r_internal_delay)
+
+/**
+ * dap8211r_read_ext() - Read extended register
+ * @phydev: PHY device structure
+ * @reg: Extended register address
+ *
+ * Reads a PHY extended register using the indirect access method.
+ * The caller must hold the MDIO bus lock.
+ *
+ * Return: Register value on success, or negative error code
+ */
+static int dap8211r_read_ext(struct phy_device *phydev, u16 reg)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+	ret = __phy_write(phydev, DAP8211R_EXT_ADD, reg);
+	if (ret < 0)
+		goto out;
+
+	ret = __phy_read(phydev, DAP8211R_EXT_DATA);
+out:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
+/**
+ * dap8211r_modify_ext() - Modify extended register bits
+ * @phydev: PHY device structure
+ * @reg: Extended register address
+ * @mask: Bit mask of bits to clear
+ * @set: Bit mask of bits to set
+ *
+ * Modifies a PHY extended register using the indirect access method.
+ * New value = (old value & ~mask) | set.
+ * The caller must hold the MDIO bus lock.
+ *
+ * Return: 0 on success, or negative error code
+ */
+static int dap8211r_modify_ext(struct phy_device *phydev, u16 reg, u16 mask, u16 set)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+	ret = __phy_write(phydev, DAP8211R_EXT_ADD, reg);
+	if (ret < 0)
+		goto out;
+
+	ret = __phy_modify(phydev, DAP8211R_EXT_DATA, mask, set);
+out:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
+/**
+ * dap8211r_config_init() - Initialize PHY
+ * @phydev: PHY device structure
+ *
+ * Configures the PHY during initialization:
+ * - TX clock invertion
+ * - RGMII delays based on interface mode
+ * - Software reset to apply settings (low active, self clear)
+ *
+ * Return: 0 on success, or negative error code
+ */
+static int dap8211r_config_init(struct phy_device *phydev)
+{
+	struct device_node *phydev_node = phydev->mdio.dev.of_node;
+	u16 set = 0, val = 0;
+	int ret;
+	s32 internal_delay;
+
+	if (of_property_read_bool(phydev_node, "dapu,tx-inverted-clk"))
+		set |= DAP8211R_RGMII_CLK_INVERT;
+
+	internal_delay = phy_get_internal_delay(phydev, dap8211r_internal_delay,
+						DAP8211R_DELAY_SIZE, true);
+	if (internal_delay < 0) {
+		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+			internal_delay = 0;
+		else
+			internal_delay = DAP8211R_DEFAULT_DEL_SEL;
+	}
+
+	set |= FIELD_PREP(DAP8211R_RGMII_RX_DEL_MASK, internal_delay);
+
+	internal_delay = phy_get_internal_delay(phydev, dap8211r_internal_delay,
+						DAP8211R_DELAY_SIZE, false);
+	if (internal_delay < 0) {
+		if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
+			internal_delay = DAP8211R_INIT_TX_DEL_VAL;
+		else
+			internal_delay = DAP8211R_DEFAULT_DEL_SEL;
+	}
+
+	set |= FIELD_PREP(DAP8211R_RGMII_TX_DEL_MASK, internal_delay);
+
+	ret = dap8211r_modify_ext(phydev, DAP8211R_PHY_CON, DAP8211R_PHY_SW_RST, 0);
+	if (ret)
+		return ret;
+
+	/* Wait for reset self-clear (max 200 us) */
+	ret = read_poll_timeout(dap8211r_read_ext, val,
+				(val & DAP8211R_PHY_SW_RST),
+				20, 200, false, phydev, DAP8211R_PHY_CON);
+	if (ret)
+		return ret;
+
+	ret = dap8211r_modify_ext(phydev, DAP8211R_RGMII_CON, DAP8211R_RGMII_CONFIG_MASK, set);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static struct phy_driver dap8211r_driver[] = {
+	{
+		PHY_ID_MATCH_EXACT(DAP8211R_PHY_ID),
+		.name		= "DAP8211R Gigabit Ethernet",
+		.config_init	= dap8211r_config_init,
+		.read_status	= genphy_read_status,
+		.set_loopback	= genphy_loopback,
+		.config_aneg	= genphy_config_aneg,
+		.suspend	= genphy_suspend,
+		.resume		= genphy_resume,
+	},
+};
+module_phy_driver(dap8211r_driver);
+
+MODULE_DESCRIPTION("DAP8211R Gigabit Ethernet PHY driver");
+MODULE_AUTHOR("Artem Shimko <a.shimko.dev@gmail.com>");
+MODULE_LICENSE("GPL");
+
+static const struct mdio_device_id __maybe_unused dap8211r_tb[] = {
+	{ DAP8211R_PHY_ID, DAP8211R_PHY_ID_MASK },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(mdio, dap8211r_tb);
+
-- 
2.43.0

Re: [PATCH net-next v3 0/2] Add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

[Maxime Chevallier]

Hi Artem,

Please slow down a bit, you need to wait at least 24h between patch
submissions :

https://docs.kernel.org/process/maintainer-netdev.html

On 7/16/26 19:33, Artem Shimko wrote:
> Hello,
> 
> This series adds support for the DAPU Telecom DAP8211R(I) Gigabit
> Ethernet PHY, commonly used in enterprise and industrial networking
> applications. The PHY supports 10/100/1000 Mbps operation with RGMII
> interface and includes features such as IEEE 802.3az Energy Efficient
> Ethernet, IEEE 1588 SyncE, and an internal packet generator for
> diagnostics.
> 
> The driver implements extended register access via indirect addressing
> (registers 0x1E/0x1F) and provides comprehensive device tree support
> for RGMII delay configuration. The rx-internal-delay-ps and
> tx-internal-delay-ps properties allow precise tuning of clock delays
> in 150 ps steps from 0 to 2250 ps. The optional dapu,tx-inverted-clk
> flag enables 180-degree TX clock phase shift for boards where signal
> integrity or MAC requirements necessitate clock inversion.

+Zhi Li

This isn't the first time we see clock inversion being used to overcome
RGMII timing issues, for setups that have too big of an internal delay,
see [1].

I'm wondering if we should either reject this on the account that this
is bad HW design, or embrace that in which case it would probably be
a good idea to come-up with more generic ways to handle that.

This patch proposes the "dapu,tx-inverted-clk" property, while Zhi Li's
patch has a dedicated compatible for that (and inversion is on RX, on the
MAC side)

If clock inversion is a common thing for MAC and PHYs to be able to do,
should we add some way of representing the RGMII delays that are
introduced by the HW itself in DT, and let drivers figure-out from that
if they need to resort to clock inversion to align clk and data correctly ?

Phylib could maybe even provide helpers for that ?

[1] : https://lore.kernel.org/netdev/20260707064159.1299-1-lizhi2@eswincomputing.com/

Maxime

Re: [PATCH net-next v3 0/2] Add DAPU Telecom DAP8211R(I) Gigabit Ethernet PHY driver

[Andrew Lunn]

On Thu, Jul 16, 2026 at 08:11:26PM +0200, Maxime Chevallier wrote:
> Hi Artem,
> 
> Please slow down a bit, you need to wait at least 24h between patch
> submissions :
> 
> https://docs.kernel.org/process/maintainer-netdev.html

Adding to that, there is no version history. How does v3 differ to
v2.

https://docs.kernel.org/process/submitting-patches.html

	Andrew

Re: [PATCH net-next v3 1/2] dt-bindings: net: add DAPU Telecom DAP8211R(I) PHY binding

[Rob Herring (Arm)]

On Thu, 16 Jul 2026 20:33:24 +0300, Artem Shimko wrote:
> Add device tree binding documentation for the DAPU Telecom DAP8211R(I)
> Gigabit Ethernet PHY.
> 
> The PHY supports TX and RX clock delays in 150 ps steps from 0 to 2250 ps,
> with a default of 1950 ps if not specified. The dapu,tx-inverted-clk flag
> provides a vendor-specific extension for boards where PCB trace length or
> MAC requirements necessitate 180-degree clock phase shift.
> 
> Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
> ---
>  .../bindings/net/dapu,dap8211r.yaml           | 73 +++++++++++++++++++
>  1 file changed, 73 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/dapu,dap8211r.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/dapu,dap8211r.example.dtb: ethernet-phy@1 (ethernet-phy-id0008.011b): 'dapu,tx-inverted-clk' does not match any of the regexes: '^#.*', '^(at25|bm|devbus|dmacap|dsa|exynos|fsi[ab]|gpio-fan|gpio-key|gpio|gpmc|hdmi|i2c-gpio),.*', '^(keypad|m25p|max8952|max8997|max8998|mpmc),.*', '^(pciclass|pinctrl-single|#pinctrl-single|PowerPC),.*', '^(pl022|pxa-mmc|rcar_sound|rotary-encoder|s5m8767|sdhci),.*', '^(simple-audio-card|st-plgpio|st-spics|ts|vsc8531),.*', '^100ask,.*', '^70mai,.*', '^8dev,.*', '^9tripod,.*', '^GEFanuc,.*', '^IBM,.*', '^ORCL,.*', '^SUNW,.*', '^[a-zA-Z0-9#_][a-zA-Z0-9#+\\-._@]{0,63}$', '^[a-zA-Z0-9+\\-._]*@[0-9a-zA-Z,]*$', '^abb,.*', '^abilis,.*', '^abracon,.*', '^abt,.*', '^acbel,.*', '^acelink,.*', '^acer,.*', '^acme,.*', '^actions,.*', '^actiontec,.*', '^active-semi,.*', '^ad,.*', '^adafruit,.*', '^adapteva,.*', '^adaptrum,.*', '^adh,.*', '^adi,.*', '^adieng,.*', '^admatec,.*', '^advantech,.*', '
 ^aeroflexgaisler,.*', '^aesop,.*', '^airoha,.*', '^al,.*', '^alcatel,.*', '^aldec,.*', '^alfa-network,.*', '^algoltek,.*', '^alientek,.*', '^allegro,.*', '^allegromicro,.*', '^alliedtelesis,.*', '^alliedvision,.*', '^allo,.*', '^allwinner,.*', '^alphascale,.*', '^alps,.*', '^alt,.*', '^altr,.*', '^amarula,.*', '^amazon,.*', '^amcc,.*', '^amd,.*', '^amediatech,.*', '^amlogic,.*', '^ampere,.*', '^amphenol,.*', '^ampire,.*', '^ams,.*', '^amstaos,.*', '^analogix,.*', '^anbernic,.*', '^andestech,.*', '^anlogic,.*', '^anvo,.*', '^aoly,.*', '^aosong,.*', '^apm,.*', '^apple,.*', '^aptina,.*', '^arasan,.*', '^archermind,.*', '^arcom,.*', '^arctic,.*', '^arcx,.*', '^arduino,.*', '^argon40,.*', '^ariaboard,.*', '^aries,.*', '^arm,.*', '^armadeus,.*', '^armchina,.*', '^armsom,.*', '^arrow,.*', '^artesyn,.*', '^asahi-kasei,.*', '^asc,.*', '^asix,.*', '^asl-tek,.*', '^aspeed,.*', '^asrock,.*', '^asteralabs,.*', '^asus,.*', '^atheros,.*', '^atlas,.*', '^atmel,.*', '^auo,.*', '^auvidea,.*', '^avago
 ,.*', '^avia,.*', '^avic,.*', '^avnet,.*', '^awinic,.*', '^axentia,.*', '^axiado,.*', '^axis,.*', '^ayaneo,.*', '^ayntec,.*', '^azoteq,.*', '^azw,.*', '^baijie,.*', '^baikal,.*', '^bananapi,.*', '^beacon,.*', '^beagle,.*', '^belling,.*', '^bestar,.*', '^bhf,.*', '^bigtreetech,.*', '^bitmain,.*', '^blaize,.*', '^bluegiga,.*', '^blutek,.*', '^boe,.*', '^bosch,.*', '^boundary,.*', '^brcm,.*', '^broadmobi,.*', '^bsh,.*', '^bst,.*', '^bticino,.*', '^buffalo,.*', '^buglabs,.*', '^bur,.*', '^bytedance,.*', '^calamp,.*', '^calao,.*', '^calaosystems,.*', '^calxeda,.*', '^cameo,.*', '^canaan,.*', '^caninos,.*', '^capella,.*', '^cascoda,.*', '^catalyst,.*', '^cavium,.*', '^cct,.*', '^cdns,.*', '^cdtech,.*', '^cellwise,.*', '^ceva,.*', '^chargebyte,.*', '^checkpoint,.*', '^chefree,.*', '^chipidea,.*', '^chipone,.*', '^chipspark,.*', '^chongzhou,.*', '^chrontel,.*', '^chrp,.*', '^chunghwa,.*', '^chuwi,.*', '^ciaa,.*', '^cirrus,.*', '^cisco,.*', '^cix,.*', '^clockwork,.*', '^cloos,.*', '^cloudeng
 ines,.*', '^cnm,.*', '^cnxt,.*', '^colorfly,.*', '^compal,.*', '^compulab,.*', '^comvetia,.*', '^congatec,.*', '^coolpi,.*', '^corechips,.*', '^coreriver,.*', '^corpro,.*', '^cortina,.*', '^cosmic,.*', '^crane,.*', '^creative,.*', '^crystalfontz,.*', '^csky,.*', '^csot,.*', '^csq,.*', '^csr,.*', '^ctera,.*', '^ctu,.*', '^cubietech,.*', '^cudy,.*', '^cui,.*', '^cypress,.*', '^cyx,.*', '^cznic,.*', '^dallas,.*', '^dataimage,.*', '^davicom,.*', '^deepcomputing,.*', '^dell,.*', '^delta,.*', '^densitron,.*', '^denx,.*', '^devantech,.*', '^dfi,.*', '^dfrobot,.*', '^dh,.*', '^difrnce,.*', '^digi,.*', '^digilent,.*', '^dimonoff,.*', '^diodes,.*', '^dioo,.*', '^displaytech,.*', '^djn,.*', '^dlc,.*', '^dlg,.*', '^dlink,.*', '^dmo,.*', '^doestek,.*', '^domintech,.*', '^dongwoon,.*', '^dptechnics,.*', '^dragino,.*', '^dream,.*', '^ds,.*', '^dserve,.*', '^dynaimage,.*', '^ea,.*', '^ebang,.*', '^ebbg,.*', '^ebs-systart,.*', '^ebv,.*', '^eckelmann,.*', '^econet,.*', '^edgeble,.*', '^edimax,.*', '^
 edt,.*', '^ees,.*', '^eeti,.*', '^efinix,.*', '^egnite,.*', '^einfochips,.*', '^eink,.*', '^elan,.*', '^element14,.*', '^elgin,.*', '^elida,.*', '^elimo,.*', '^elpida,.*', '^embedfire,.*', '^embest,.*', '^emcraft,.*', '^emlid,.*', '^emmicro,.*', '^empire-electronix,.*', '^emtrion,.*', '^enbw,.*', '^enclustra,.*', '^endian,.*', '^endless,.*', '^ene,.*', '^energymicro,.*', '^engicam,.*', '^engleder,.*', '^epcos,.*', '^epfl,.*', '^epson,.*', '^esp,.*', '^est,.*', '^eswin,.*', '^etekmicro,.*', '^ettus,.*', '^eukrea,.*', '^everest,.*', '^everspin,.*', '^evervision,.*', '^exar,.*', '^excito,.*', '^exegin,.*', '^ezchip,.*', '^ezurio,.*', '^facebook,.*', '^fairchild,.*', '^fairphone,.*', '^faraday,.*', '^fascontek,.*', '^fastrax,.*', '^fcs,.*', '^feixin,.*', '^feiyang,.*', '^fii,.*', '^firefly,.*', '^fitipower,.*', '^flipkart,.*', '^focaltech,.*', '^focuslcds,.*', '^forlinx,.*', '^foursemi,.*', '^foxlink,.*', '^freebox,.*', '^freecom,.*', '^frida,.*', '^friendlyarm,.*', '^fsl,.*', '^fujitsu
 ,.*', '^fxtec,.*', '^galaxycore,.*', '^gameforce,.*', '^gardena,.*', '^gateway,.*', '^gateworks,.*', '^gcw,.*', '^ge,.*', '^geekbuying,.*', '^gef,.*', '^gehc,.*', '^gemei,.*', '^gemtek,.*', '^genesys,.*', '^genexis,.*', '^geniatech,.*', '^giantec,.*', '^giantplus,.*', '^gira,.*', '^glinet,.*', '^globalscale,.*', '^globaltop,.*', '^gmt,.*', '^gocontroll,.*', '^goldelico,.*', '^goodix,.*', '^google,.*', '^goramo,.*', '^gplus,.*', '^graperain,.*', '^grinn,.*', '^grmn,.*', '^gumstix,.*', '^gw,.*', '^hannstar,.*', '^haochuangyi,.*', '^haoyu,.*', '^hardkernel,.*', '^hce,.*', '^headacoustics,.*', '^hechuang,.*', '^hideep,.*', '^himax,.*', '^hinlink,.*', '^hirschmann,.*', '^hisi,.*', '^hisilicon,.*', '^hit,.*', '^hitex,.*', '^hitron,.*', '^holitech,.*', '^holt,.*', '^holtek,.*', '^honestar,.*', '^honeywell,.*', '^honor,.*', '^hoperf,.*', '^hoperun,.*', '^hp,.*', '^hpe,.*', '^hsg,.*', '^htc,.*', '^huawei,.*', '^hugsun,.*', '^huiling,.*', '^hwacom,.*', '^hxt,.*', '^hycon,.*', '^hydis,.*', '^h
 ynetek,.*', '^hynitron,.*', '^hynix,.*', '^hyundai,.*', '^i2se,.*', '^ibm,.*', '^icplus,.*', '^idt,.*', '^iei,.*', '^ifi,.*', '^ifm,.*', '^ilitek,.*', '^imagis,.*', '^img,.*', '^imi,.*', '^inanbo,.*', '^incircuit,.*', '^incostartec,.*', '^indiedroid,.*', '^inet-tek,.*', '^infineon,.*', '^inforce,.*', '^ingenic,.*', '^ingrasys,.*', '^injoinic,.*', '^innocomm,.*', '^innolux,.*', '^inside-secure,.*', '^insignal,.*', '^inspur,.*', '^intel,.*', '^intercontrol,.*', '^invensense,.*', '^inventec,.*', '^inversepath,.*', '^iom,.*', '^irondevice,.*', '^isee,.*', '^isil,.*', '^issi,.*', '^ite,.*', '^itead,.*', '^itian,.*', '^ivo,.*', '^iwave,.*', '^jadard,.*', '^jasonic,.*', '^jdi,.*', '^jedec,.*', '^jenson,.*', '^jesurun,.*', '^jethome,.*', '^jianda,.*', '^jide,.*', '^joz,.*', '^jty,.*', '^jutouch,.*', '^kam,.*', '^karo,.*', '^keithkoep,.*', '^keymile,.*', '^khadas,.*', '^kiebackpeter,.*', '^kinetic,.*', '^kingdisplay,.*', '^kingnovel,.*', '^kionix,.*', '^kobo,.*', '^kobol,.*', '^koe,.*', '^ko
 ntron,.*', '^kosagi,.*', '^kvg,.*', '^kyo,.*', '^lacie,.*', '^laird,.*', '^lamobo,.*', '^lantiq,.*', '^lattice,.*', '^lckfb,.*', '^lctech,.*', '^leadtek,.*', '^leez,.*', '^lego,.*', '^lemaker,.*', '^lenovo,.*', '^lg,.*', '^lgphilips,.*', '^libretech,.*', '^licheepi,.*', '^linaro,.*', '^lincolntech,.*', '^lineartechnology,.*', '^linkease,.*', '^linksprite,.*', '^linksys,.*', '^linutronix,.*', '^linux,.*', '^linx,.*', '^liontron,.*', '^liteon,.*', '^litex,.*', '^lltc,.*', '^logicpd,.*', '^logictechno,.*', '^longcheer,.*', '^lontium,.*', '^loongmasses,.*', '^loongson,.*', '^lsi,.*', '^luckfox,.*', '^lunzn,.*', '^luxshare,.*', '^luxul,.*', '^lwn,.*', '^lxa,.*', '^lxd,.*', '^m5stack,.*', '^macnica,.*', '^mantix,.*', '^mapleboard,.*', '^marantec,.*', '^marvell,.*', '^maxbotix,.*', '^maxim,.*', '^maxlinear,.*', '^maxtor,.*', '^mayqueen,.*', '^mbvl,.*', '^mcube,.*', '^meas,.*', '^mecer,.*', '^mediatek,.*', '^medion,.*', '^megachips,.*', '^mele,.*', '^melexis,.*', '^melfas,.*', '^mellanox,.*
 ', '^memsensing,.*', '^memsic,.*', '^menlo,.*', '^mentor,.*', '^meraki,.*', '^merrii,.*', '^methode,.*', '^micrel,.*', '^microchip,.*', '^microcrystal,.*', '^micron,.*', '^microsoft,.*', '^microsys,.*', '^microtips,.*', '^mikroe,.*', '^mikrotik,.*', '^milianke,.*', '^milkv,.*', '^miniand,.*', '^minix,.*', '^mips,.*', '^miramems,.*', '^mitsubishi,.*', '^mitsumi,.*', '^mixel,.*', '^miyoo,.*', '^mntre,.*', '^mobileye,.*', '^modtronix,.*', '^moortec,.*', '^mosaixtech,.*', '^motorcomm,.*', '^motorola,.*', '^moxa,.*', '^mpl,.*', '^mps,.*', '^mqmaker,.*', '^mrvl,.*', '^mscc,.*', '^msi,.*', '^mstar,.*', '^mti,.*', '^multi-inno,.*', '^mundoreader,.*', '^murata,.*', '^mxic,.*', '^mxicy,.*', '^myir,.*', '^national,.*', '^neardi,.*', '^nec,.*', '^neofidelity,.*', '^neonode,.*', '^netcube,.*', '^netgear,.*', '^netlogic,.*', '^netron-dy,.*', '^netronix,.*', '^netxeon,.*', '^neweast,.*', '^newhaven,.*', '^newvision,.*', '^nexbox,.*', '^nextthing,.*', '^ni,.*', '^nicera,.*', '^nintendo,.*', '^nlt,.
 *', '^nokia,.*', '^nordic,.*', '^nothing,.*', '^novatech,.*', '^novatek,.*', '^novtech,.*', '^nuclei,.*', '^numonyx,.*', '^nutsboard,.*', '^nuvoton,.*', '^nvd,.*', '^nvidia,.*', '^nxp,.*', '^oceanic,.*', '^ocs,.*', '^oct,.*', '^okaya,.*', '^oki,.*', '^olimex,.*', '^olpc,.*', '^oneplus,.*', '^onething,.*', '^onie,.*', '^onion,.*', '^onnn,.*', '^ontat,.*', '^opalkelly,.*', '^openailab,.*', '^opencores,.*', '^openembed,.*', '^openpandora,.*', '^openrisc,.*', '^openwrt,.*', '^option,.*', '^oranth,.*', '^orisetech,.*', '^ortustech,.*', '^osddisplays,.*', '^osmc,.*', '^ouya,.*', '^overkiz,.*', '^ovti,.*', '^oxsemi,.*', '^ozzmaker,.*', '^panasonic,.*', '^parade,.*', '^parallax,.*', '^particle,.*', '^pda,.*', '^pegatron,.*', '^pericom,.*', '^pervasive,.*', '^phicomm,.*', '^phontech,.*', '^phytec,.*', '^picochip,.*', '^pinctrl-[0-9]+$', '^pine64,.*', '^pineriver,.*', '^pixcir,.*', '^plantower,.*', '^plathome,.*', '^plda,.*', '^plx,.*', '^ply,.*', '^pni,.*', '^pocketbook,.*', '^polaroid,.*', 
 '^polyhex,.*', '^pool[0-3],.*', '^portwell,.*', '^poslab,.*', '^pov,.*', '^powertip,.*', '^powervr,.*', '^powkiddy,.*', '^pri,.*', '^primeview,.*', '^primux,.*', '^probox2,.*', '^prt,.*', '^pulsedlight,.*', '^purism,.*', '^puya,.*', '^qca,.*', '^qcom,.*', '^qemu,.*', '^qi,.*', '^qiaodian,.*', '^qihua,.*', '^qishenglong,.*', '^qnap,.*', '^qstcorp,.*', '^quanta,.*', '^radxa,.*', '^raidsonic,.*', '^ralink,.*', '^ramtron,.*', '^raspberrypi,.*', '^raumfeld,.*', '^raydium,.*', '^raystar,.*', '^rda,.*', '^realtek,.*', '^relfor,.*', '^remarkable,.*', '^renesas,.*', '^rervision,.*', '^retronix,.*', '^revotics,.*', '^rex,.*', '^rfdigital,.*', '^richtek,.*', '^ricoh,.*', '^rikomagic,.*', '^riot,.*', '^riscv,.*', '^riverdi,.*', '^rockchip,.*', '^rocktech,.*', '^rohm,.*', '^ronbo,.*', '^ronetix,.*', '^roofull,.*', '^roseapplepi,.*', '^rve,.*', '^saef,.*', '^sakurapi,.*', '^samsung,.*', '^samtec,.*', '^sancloud,.*', '^sandisk,.*', '^satoz,.*', '^sbs,.*', '^schindler,.*', '^schneider,.*', '^schule
 rcontrol,.*', '^sciosense,.*', '^sdmc,.*', '^seagate,.*', '^seeed,.*', '^seirobotics,.*', '^semtech,.*', '^senseair,.*', '^sensirion,.*', '^sensortek,.*', '^sercomm,.*', '^sff,.*', '^sgd,.*', '^sgmicro,.*', '^sgx,.*', '^sharp,.*', '^shift,.*', '^shimafuji,.*', '^shineworld,.*', '^shiratech,.*', '^si-en,.*', '^si-linux,.*', '^sielaff,.*', '^siemens,.*', '^sifive,.*', '^siflower,.*', '^sigma,.*', '^sii,.*', '^sil,.*', '^silabs,.*', '^silan,.*', '^silead,.*', '^silergy,.*', '^silex-insight,.*', '^siliconfile,.*', '^siliconmitus,.*', '^silvaco,.*', '^simtek,.*', '^sinlinx,.*', '^sinovoip,.*', '^sinowealth,.*', '^sipeed,.*', '^sirf,.*', '^sis,.*', '^sitronix,.*', '^skov,.*', '^skyworks,.*', '^smartfiber,.*', '^smartlabs,.*', '^smartrg,.*', '^smi,.*', '^smsc,.*', '^snps,.*', '^sochip,.*', '^socionext,.*', '^solidrun,.*', '^solomon,.*', '^somfy,.*', '^sony,.*', '^sophgo,.*', '^sourceparts,.*', '^spacemit,.*', '^spansion,.*', '^sparkfun,.*', '^spinalhdl,.*', '^sprd,.*', '^square,.*', '^ssi,
 .*', '^sst,.*', '^sstar,.*', '^st,.*', '^st-ericsson,.*', '^starfive,.*', '^starry,.*', '^startek,.*', '^starterkit,.*', '^ste,.*', '^stericsson,.*', '^storlink,.*', '^storm,.*', '^storopack,.*', '^summit,.*', '^sunchip,.*', '^sundance,.*', '^sunplus,.*', '^supermicro,.*', '^swir,.*', '^syna,.*', '^synaptics,.*', '^synology,.*', '^synopsys,.*', '^taiguanck,.*', '^taos,.*', '^tbs,.*', '^tbs-biometrics,.*', '^tcg,.*', '^tcl,.*', '^tcs,.*', '^tcu,.*', '^tdo,.*', '^team-source-display,.*', '^technexion,.*', '^technologic,.*', '^techstar,.*', '^techwell,.*', '^teejet,.*', '^teltonika,.*', '^tempo,.*', '^tenda,.*', '^tenstorrent,.*', '^terasic,.*', '^tesla,.*', '^test,.*', '^tfc,.*', '^thead,.*', '^thine,.*', '^thingyjp,.*', '^thundercomm,.*', '^thwc,.*', '^ti,.*', '^tianma,.*', '^tlm,.*', '^tmt,.*', '^topeet,.*', '^topic,.*', '^topland,.*', '^toppoly,.*', '^topwise,.*', '^toradex,.*', '^toshiba,.*', '^toumaz,.*', '^tpk,.*', '^tplink,.*', '^tpo,.*', '^tq,.*', '^transpeed,.*', '^traverse,.
 *', '^tronfy,.*', '^tronsmart,.*', '^truly,.*', '^tsd,.*', '^turing,.*', '^tuxedo,.*', '^tyan,.*', '^tyhx,.*', '^u-blox,.*', '^u-boot,.*', '^ubnt,.*', '^ucrobotics,.*', '^udoo,.*', '^ufispace,.*', '^ugoos,.*', '^ultrapower,.*', '^ultrarisc,.*', '^ultratronik,.*', '^uni-t,.*', '^uniwest,.*', '^upisemi,.*', '^urt,.*', '^usi,.*', '^usr,.*', '^utoo,.*', '^v3,.*', '^vaisala,.*', '^valve,.*', '^vamrs,.*', '^variscite,.*', '^vdl,.*', '^verbatim,.*', '^verisilicon,.*', '^vertexcom,.*', '^via,.*', '^vialab,.*', '^vicharak,.*', '^vicor,.*', '^videostrong,.*', '^virtio,.*', '^virtual,.*', '^vishay,.*', '^visionox,.*', '^vitesse,.*', '^vivante,.*', '^vivax,.*', '^vocore,.*', '^voipac,.*', '^voltafield,.*', '^vot,.*', '^vscom,.*', '^vxt,.*', '^wacom,.*', '^wanchanglong,.*', '^wand,.*', '^waveshare,.*', '^wd,.*', '^we,.*', '^welltech,.*', '^wetek,.*', '^wexler,.*', '^whwave,.*', '^wi2wi,.*', '^widora,.*', '^wiko,.*', '^wiligear,.*', '^willsemi,.*', '^winbond,.*', '^wingtech,.*', '^winlink,.*', '^
 winsen,.*', '^winstar,.*', '^wirelesstag,.*', '^wits,.*', '^wlf,.*', '^wm,.*', '^wobo,.*', '^wolfvision,.*', '^x-powers,.*', '^xen,.*', '^xes,.*', '^xiaomi,.*', '^xicor,.*', '^xillybus,.*', '^xingbangda,.*', '^xinpeng,.*', '^xiphera,.*', '^xlnx,.*', '^xnano,.*', '^xunlong,.*', '^xylon,.*', '^yadro,.*', '^yamaha,.*', '^yes-optoelectronics,.*', '^yic,.*', '^yiming,.*', '^ylm,.*', '^yna,.*', '^yones-toptech,.*', '^youyeetoo,.*', '^ys,.*', '^ysoft,.*', '^yuridenki,.*', '^yuzukihd,.*', '^zarlink,.*', '^zealz,.*', '^zeitec,.*', '^zidoo,.*', '^zii,.*', '^zinitix,.*', '^zkmagic,.*', '^zte,.*', '^zyxel,.*'
	from schema $id: http://devicetree.org/schemas/vendor-prefixes.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.kernel.org/project/devicetree/patch/20260716173325.653164-2-a.shimko.dev@gmail.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.