* [PATCH v2] vdpa/vp_vdpa: Wait for device reset to complete
@ 2026-11-16 3:01 Yuho Choi
2026-11-16 8:18 ` Michael S. Tsirkin
0 siblings, 1 reply; 2+ messages in thread
From: Yuho Choi @ 2026-11-16 3:01 UTC (permalink / raw)
To: Michael S. Tsirkin, Jason Wang, Eugenio Pérez
Cc: Xuan Zhuo, virtualization, linux-kernel, Yuho Choi
vp_vdpa_reset() writes 0 to device_status and returns success right
away. The virtio specification requires the driver to wait until a read
of device_status returns 0 before reinitializing the device, and
virtio_pci_modern's vp_reset() does exactly that: the read-back flushes
the posted status write and any in-flight device writes, including
MSI-X messages.
Without it, vhost-vdpa (or virtio-vdpa) can go on to tear down the
IOTLB/IOMMU mappings or reprogram the queues while the device has not
yet finished its reset, and may still be DMAing to the old virtqueue
addresses. The MSI-X vectors are also freed while an interrupt from
the old configuration may still be in flight.
Poll device_status after writing 0, in the same way as vp_reset(),
before freeing the IRQs and returning.
Fixes: 64b9f64f80a6 ("vdpa: introduce virtio pci driver")
Signed-off-by: Yuho Choi <oss.patchbox@gmail.com>
---
v2:
- Drop Cc: stable, as this has not been reproduced.
- Rebased on current mainline. No code change.
v1: https://lore.kernel.org/r/20260926211507.1330179-1-oss.patchbox@gmail.com
Like vp_reset(), the new loop has no bound, so a surprise-removed
device that reads back all ones would keep it spinning (the Sashiko
review of v1 pointed this out). I kept it the same as vp_reset()
rather than handling that case only here.
Compile-tested only (x86_64 defconfig + VP_VDPA, W=1).
drivers/vdpa/virtio_pci/vp_vdpa.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/vdpa/virtio_pci/vp_vdpa.c b/drivers/vdpa/virtio_pci/vp_vdpa.c
index 646efd9384fb..eba82ff253ea 100644
--- a/drivers/vdpa/virtio_pci/vp_vdpa.c
+++ b/drivers/vdpa/virtio_pci/vp_vdpa.c
@@ -8,6 +8,7 @@
* Based on virtio_pci_modern.c.
*/
+#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -236,6 +237,9 @@ static int vp_vdpa_reset(struct vdpa_device *vdpa)
u8 s = vp_vdpa_get_status(vdpa);
vp_modern_set_status(mdev, 0);
+ /* Wait for the reset to complete */
+ while (vp_modern_get_status(mdev))
+ fsleep(1000);
if (s & VIRTIO_CONFIG_S_DRIVER_OK)
vp_vdpa_free_irq(vp_vdpa);
base-commit: 067c5c24cef23d913b67eaaf71ae67e7169a6620
--
2.43.0
^ permalink raw reply related [flat|nested] 2+ messages in thread* Re: [PATCH v2] vdpa/vp_vdpa: Wait for device reset to complete
2026-11-16 3:01 [PATCH v2] vdpa/vp_vdpa: Wait for device reset to complete Yuho Choi
@ 2026-11-16 8:18 ` Michael S. Tsirkin
0 siblings, 0 replies; 2+ messages in thread
From: Michael S. Tsirkin @ 2026-11-16 8:18 UTC (permalink / raw)
To: Yuho Choi
Cc: Jason Wang, Eugenio Pérez, Xuan Zhuo, virtualization,
linux-kernel
On Sun, Nov 15, 2026 at 10:01:44PM -0500, Yuho Choi wrote:
> vp_vdpa_reset() writes 0 to device_status and returns success right
> away. The virtio specification requires the driver to wait until a read
> of device_status returns 0 before reinitializing the device, and
> virtio_pci_modern's vp_reset() does exactly that: the read-back flushes
> the posted status write and any in-flight device writes, including
> MSI-X messages.
>
> Without it, vhost-vdpa (or virtio-vdpa) can go on to tear down the
> IOTLB/IOMMU mappings or reprogram the queues while the device has not
> yet finished its reset, and may still be DMAing to the old virtqueue
> addresses. The MSI-X vectors are also freed while an interrupt from
> the old configuration may still be in flight.
>
> Poll device_status after writing 0, in the same way as vp_reset(),
> before freeing the IRQs and returning.
>
> Fixes: 64b9f64f80a6 ("vdpa: introduce virtio pci driver")
> Signed-off-by: Yuho Choi <oss.patchbox@gmail.com>
> ---
> v2:
> - Drop Cc: stable, as this has not been reproduced.
> - Rebased on current mainline. No code change.
>
> v1: https://lore.kernel.org/r/20260926211507.1330179-1-oss.patchbox@gmail.com
>
> Like vp_reset(), the new loop has no bound, so a surprise-removed
> device that reads back all ones would keep it spinning (the Sashiko
> review of v1 pointed this out). I kept it the same as vp_reset()
> rather than handling that case only here.
>
> Compile-tested only (x86_64 defconfig + VP_VDPA, W=1).
If you can't bother testing, why should I bother merging?
> drivers/vdpa/virtio_pci/vp_vdpa.c | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/drivers/vdpa/virtio_pci/vp_vdpa.c b/drivers/vdpa/virtio_pci/vp_vdpa.c
> index 646efd9384fb..eba82ff253ea 100644
> --- a/drivers/vdpa/virtio_pci/vp_vdpa.c
> +++ b/drivers/vdpa/virtio_pci/vp_vdpa.c
> @@ -8,6 +8,7 @@
> * Based on virtio_pci_modern.c.
> */
>
> +#include <linux/delay.h>
> #include <linux/interrupt.h>
> #include <linux/module.h>
> #include <linux/pci.h>
> @@ -236,6 +237,9 @@ static int vp_vdpa_reset(struct vdpa_device *vdpa)
> u8 s = vp_vdpa_get_status(vdpa);
>
> vp_modern_set_status(mdev, 0);
> + /* Wait for the reset to complete */
> + while (vp_modern_get_status(mdev))
> + fsleep(1000);
>
> if (s & VIRTIO_CONFIG_S_DRIVER_OK)
> vp_vdpa_free_irq(vp_vdpa);
>
> base-commit: 067c5c24cef23d913b67eaaf71ae67e7169a6620
> --
> 2.43.0
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2026-11-16 8:18 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-16 3:01 [PATCH v2] vdpa/vp_vdpa: Wait for device reset to complete Yuho Choi
2026-11-16 8:18 ` Michael S. Tsirkin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox