* PROBLEM: Radeon display connector : No monitor connected or invalid EDID
@ 2011-11-13 17:27 Treeve Jelbert
2011-11-13 18:47 ` Dave Airlie
2011-11-23 20:37 ` Joseph Salisbury
0 siblings, 2 replies; 5+ messages in thread
From: Treeve Jelbert @ 2011-11-13 17:27 UTC (permalink / raw)
To: linux-kernel
PROBLEM: Radeon display connector : No monitor connected or invalid EDID
​
Since installing kernel-3.1.1 the screen goes blank during the boot and I am
unable to do anything, not even ssh into the box.
​
linux-3.1.0 worked ok. There are no other changes to the system. Both were
built using the same config file.
​
When I reboot into 3.1.0 and check the log messages, I see
​
Nov 13 14:31:22 Edge-64 kernel: [ 0.055378] CPU0: AMD A6-3400M APU with
Radeon(tm) HD Graphics stepping 00
​
# grep '\[drm\]' messages |cut -d: -f4-
[ 0.645028] [drm] Initialized drm 1.1.0 20060810
[ 14.128321] [drm] radeon defaulting to kernel modesetting.
[ 14.128391] [drm] radeon kernel modesetting enabled.
[ 14.129217] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647
0x17AA:0x21EA).
[ 14.129410] [drm] register mmio base: 0xF0B00000
[ 14.129476] [drm] register mmio size: 262144
[ 14.130388] [drm] Detected VRAM RAM=512M, BAR=256M
[ 14.130459] [drm] RAM width 32bits DDR
[ 14.130848] [drm] radeon: 512M of VRAM memory ready
[ 14.130912] [drm] radeon: 512M of GTT memory ready.
[ 14.131021] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 14.131085] [drm] Driver supports precise vblank timestamp query.
[ 14.131281] [drm] radeon: irq initialized.
[ 14.131347] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 14.132538] [drm] Loading SUMO Microcode
[ 14.547990] [drm] ring test succeeded in 1 usecs
[ 14.548128] [drm] radeon: ib pool ready.
[ 14.548249] [drm] ib test succeeded in 0 usecs
[ 14.551990] [drm] Radeon Display Connectors
[ 14.552056] [drm] Connector 0:
[ 14.552119] [drm] VGA
[ 14.552179] [drm] HPD2
[ 14.552242] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448
0x644c 0x644c
[ 14.552336] [drm] Encoders:
[ 14.552397] [drm] CRT1: INTERNAL_UNIPHY2
[ 14.552473] [drm] CRT1: NUTMEG
[ 14.552535] [drm] Connector 1:
[ 14.552596] [drm] LVDS
[ 14.552657] [drm] HPD1
[ 14.552718] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438
0x643c 0x643c
[ 14.552809] [drm] Encoders:
[ 14.552870] [drm] LCD1: INTERNAL_UNIPHY2
[ 14.552932] [drm] LCD1: TRAVIS
[ 14.552994] [drm] Connector 2:
[ 14.553055] [drm] HDMI-A
[ 14.553115] [drm] HPD3
[ 14.553176] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458
0x645c 0x645c
[ 14.553266] [drm] Encoders:
[ 14.553327] [drm] DFP1: INTERNAL_UNIPHY
[ 14.952397] [drm] Radeon display connector VGA-1: No monitor connected or
invalid EDID
[ 15.352332] [drm] Radeon display connector LVDS-1: No monitor connected or
invalid EDID
[ 15.752357] [drm] Radeon display connector HDMI-A-1: No monitor connected
or invalid EDID
[ 15.779878] [drm] Internal thermal controller without fan control
[ 15.780236] [drm] radeon: power management initialized
[ 16.014394] [drm] fb mappable at 0xE0141000
[ 16.014506] [drm] vram apper at 0xE0000000
[ 16.014568] [drm] size 4325376
[ 16.014629] [drm] fb depth is 24
[ 16.014690] [drm] pitch is 5632
[ 16.111788] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on
minor 0
​
at this point the log ends.
​
​
I also see
​
[ 13.411889] thinkpad_acpi: Lenovo ThinkPad E525, model 12002JG
[ 14.129616] ATOM BIOS: Lenovo
​
Those messages did not appear in 3.1.0
I am not sure of the meaning of ATOM, but I have an AMD system, not Intel.
​
​
Keywords:graphics drm radeon Lenovo
​
The following data is from the running linux-3.1.0
$ lspci -vvv
​
​
00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
Complex
Subsystem: Lenovo Device 21ea
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64
​
00:01.0 VGA compatible controller: ATI Technologies Inc Device 9647 (prog-if
00 [VGA controller])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 4000 [size=256]
Region 2: Memory at f0b00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1
unlimited
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM
unknown, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train-
SlotClk- DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel modules: radeon
​
00:01.1 Audio device: ATI Technologies Inc Device 1714
Subsystem: Lenovo Device 21ea
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 46
Region 0: Memory at f0b44000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<4us, L1
unlimited
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM
unknown, Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train-
SlotClk- DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4181
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: snd_hda_intel
​
00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
Port (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug- Surprise-
Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis+,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4141
Capabilities: [b0] Subsystem: Lenovo Device 21ea
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: pcieport
​
00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller
[AHCI mode] (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 45
Region 0: I/O ports at 4118 [size=8]
Region 1: I/O ports at 4124 [size=4]
Region 2: I/O ports at 4110 [size=8]
Region 3: I/O ports at 4120 [size=4]
Region 4: I/O ports at 4100 [size=16]
Region 5: Memory at f0b4b000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [50] MSI: Enable+ Count=1/16 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4171
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Kernel driver in use: ahci
​
00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
Controller (rev 11) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0b4a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
​
00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
Controller (rev 11) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0b4bb00 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
​
00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
Controller (rev 11) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0b49000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
​
00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
Controller (rev 11) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0b4ba00 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
​
00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 13)
Subsystem: Lenovo Device 21ea
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller
(rev 01)
Subsystem: Lenovo Device 21ea
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0b40000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel
​
00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
​
00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
​
00:14.7 SD Host controller: Advanced Micro Devices [AMD] Hudson SD Flash
Controller (prog-if 01)
Subsystem: Lenovo Device 21ea
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 71, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0b4b900 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
​
00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0 (prog-if 00
[Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x16, TrErr- Train-
SlotClk+ DLActive-
BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4149
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: pcieport
​
00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1 (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f0a00000-f0afffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <64ns,
L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive+
BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4151
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: pcieport
​
00:15.2 PCI bridge: Advanced Micro Devices [AMD] Device 43a2 (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0900000-f09fffff
Prefetchable memory behind bridge: 00000000f0c00000-00000000f0dfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <64ns,
L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4159
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: pcieport
​
00:15.3 PCI bridge: Advanced Micro Devices [AMD] Device 43a3 (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0500000-f08fffff
Prefetchable memory behind bridge: 00000000f0100000-00000000f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0
<64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x16, TrErr- Train-
SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
HotPlug+ Surprise-
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4161
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
Len=010
<?>
Kernel driver in use: pcieport
​
00:16.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
Controller (rev 11) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0b48000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
​
00:16.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
Controller (rev 11) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0b4b800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
​
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 0 (rev 43)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 1
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 2
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
​
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 4
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 6
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
Function 7
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
​
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
Express Gigabit Ethernet controller (rev 06)
Subsystem: Lenovo Device 21ea
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 47
Region 0: I/O ports at 3000 [size=256]
Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4189
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0
<512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Unknown small resource type 00, will not decode more.
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn-
ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 3a-0b-00-00-68-4c-e0-00
Kernel driver in use: r8169
Kernel modules: r8169
​
04:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 04) (prog-if 01)
Subsystem: Lenovo Device 21ea
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f0a00200 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1
unlimited
ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <4us,
L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [800 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn-
ChkCap+ ChkEn-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
​
05:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE
802.11b/g/n WiFi Adapter (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at f0900000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0
<512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn-
ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
Kernel driver in use: rtl8192ce
Kernel modules: rtl8192ce
​
​
​
​
​
$ lsmod
Module Size Used by
rtl8192ce 69655 0
rtl8192c_common 54535 1 rtl8192ce
cfbcopyarea 3217 0
ohci_hcd 20690 0
sdhci_pci 8440 0
rtlwifi 87860 1 rtl8192ce
sdhci 21347 1 sdhci_pci
cfbimgblt 1969 0
mmc_core 67307 1 sdhci
r8169 43238 0
cfbfillrect 3581 0
processor 22993 4
mii 3707 1 r8169
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: PROBLEM: Radeon display connector : No monitor connected or invalid EDID
2011-11-13 17:27 PROBLEM: Radeon display connector : No monitor connected or invalid EDID Treeve Jelbert
@ 2011-11-13 18:47 ` Dave Airlie
2011-11-13 20:36 ` Alex Deucher
2011-11-23 20:37 ` Joseph Salisbury
1 sibling, 1 reply; 5+ messages in thread
From: Dave Airlie @ 2011-11-13 18:47 UTC (permalink / raw)
To: Treeve Jelbert; +Cc: linux-kernel, Alex Deucher
cc Alex.
> Since installing kernel-3.1.1 the screen goes blank during the boot and I am
> unable to do anything, not even ssh into the box.
> ​
> linux-3.1.0 worked ok. There are no other changes to the system. Both were
> built using the same config file.
> ​
> When I reboot into 3.1.0 and check the log messages, I see
> ​
> Nov 13 14:31:22 Edge-64 kernel: [ 0.055378] CPU0: AMD A6-3400M APU with
> Radeon(tm) HD Graphics stepping 00
> ​
> # grep '\[drm\]' messages |cut -d: -f4-
> [ 0.645028] [drm] Initialized drm 1.1.0 20060810
> [ 14.128321] [drm] radeon defaulting to kernel modesetting.
> [ 14.128391] [drm] radeon kernel modesetting enabled.
> [ 14.129217] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647
> 0x17AA:0x21EA).
> [ 14.129410] [drm] register mmio base: 0xF0B00000
> [ 14.129476] [drm] register mmio size: 262144
> [ 14.130388] [drm] Detected VRAM RAM=512M, BAR=256M
> [ 14.130459] [drm] RAM width 32bits DDR
> [ 14.130848] [drm] radeon: 512M of VRAM memory ready
> [ 14.130912] [drm] radeon: 512M of GTT memory ready.
> [ 14.131021] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
> [ 14.131085] [drm] Driver supports precise vblank timestamp query.
> [ 14.131281] [drm] radeon: irq initialized.
> [ 14.131347] [drm] GART: num cpu pages 131072, num gpu pages 131072
> [ 14.132538] [drm] Loading SUMO Microcode
> [ 14.547990] [drm] ring test succeeded in 1 usecs
> [ 14.548128] [drm] radeon: ib pool ready.
> [ 14.548249] [drm] ib test succeeded in 0 usecs
> [ 14.551990] [drm] Radeon Display Connectors
> [ 14.552056] [drm] Connector 0:
> [ 14.552119] [drm] VGA
> [ 14.552179] [drm] HPD2
> [ 14.552242] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448
> 0x644c 0x644c
> [ 14.552336] [drm] Encoders:
> [ 14.552397] [drm] CRT1: INTERNAL_UNIPHY2
> [ 14.552473] [drm] CRT1: NUTMEG
> [ 14.552535] [drm] Connector 1:
> [ 14.552596] [drm] LVDS
> [ 14.552657] [drm] HPD1
> [ 14.552718] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438
> 0x643c 0x643c
> [ 14.552809] [drm] Encoders:
> [ 14.552870] [drm] LCD1: INTERNAL_UNIPHY2
> [ 14.552932] [drm] LCD1: TRAVIS
> [ 14.552994] [drm] Connector 2:
> [ 14.553055] [drm] HDMI-A
> [ 14.553115] [drm] HPD3
> [ 14.553176] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458
> 0x645c 0x645c
> [ 14.553266] [drm] Encoders:
> [ 14.553327] [drm] DFP1: INTERNAL_UNIPHY
> [ 14.952397] [drm] Radeon display connector VGA-1: No monitor connected or
> invalid EDID
> [ 15.352332] [drm] Radeon display connector LVDS-1: No monitor connected or
> invalid EDID
> [ 15.752357] [drm] Radeon display connector HDMI-A-1: No monitor connected
> or invalid EDID
> [ 15.779878] [drm] Internal thermal controller without fan control
> [ 15.780236] [drm] radeon: power management initialized
> [ 16.014394] [drm] fb mappable at 0xE0141000
> [ 16.014506] [drm] vram apper at 0xE0000000
> [ 16.014568] [drm] size 4325376
> [ 16.014629] [drm] fb depth is 24
> [ 16.014690] [drm] pitch is 5632
> [ 16.111788] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on
> minor 0
> ​
> at this point the log ends.
> ​
> ​
> I also see
> ​
> [ 13.411889] thinkpad_acpi: Lenovo ThinkPad E525, model 12002JG
> [ 14.129616] ATOM BIOS: Lenovo
> ​
> Those messages did not appear in 3.1.0
> I am not sure of the meaning of ATOM, but I have an AMD system, not Intel.
> ​
> ​
> Keywords:graphics drm radeon Lenovo
> ​
> The following data is from the running linux-3.1.0
> $ lspci -vvv
> ​
> ​
> 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Complex
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> ​
> 00:01.0 VGA compatible controller: ATI Technologies Inc Device 9647 (prog-if
> 00 [VGA controller])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Region 1: I/O ports at 4000 [size=256]
> Region 2: Memory at f0b00000 (32-bit, non-prefetchable) [size=256K]
> Expansion ROM at <unassigned> [disabled]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1 <1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel modules: radeon
> ​
> 00:01.1 Audio device: ATI Technologies Inc Device 1714
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 46
> Region 0: Memory at f0b44000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1 <1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4181
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: snd_hda_intel
> ​
> 00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Port (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00003000-00003fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug- Surprise-
> Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet+ LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis+,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4141
> Capabilities: [b0] Subsystem: Lenovo Device 21ea
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller
> [AHCI mode] (prog-if 01 [AHCI 1.0])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> Interrupt: pin A routed to IRQ 45
> Region 0: I/O ports at 4118 [size=8]
> Region 1: I/O ports at 4124 [size=4]
> Region 2: I/O ports at 4110 [size=8]
> Region 3: I/O ports at 4120 [size=4]
> Region 4: I/O ports at 4100 [size=16]
> Region 5: Memory at f0b4b000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [50] MSI: Enable+ Count=1/16 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4171
> Capabilities: [70] SATA HBA v1.0 InCfgSpace
> Kernel driver in use: ahci
> ​
> 00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b4a000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4bb00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b49000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4ba00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 13)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller
> (rev 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b40000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: snd_hda_intel
> ​
> 00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> ​
> 00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)
> (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> ​
> 00:14.7 SD Host controller: Advanced Micro Devices [AMD] Hudson SD Flash
> Controller (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 71, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b4b900 (32-bit, non-prefetchable) [size=256]
> Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0 (prog-if 00
> [Normal decode])
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4149
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f0a00000-f0afffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <64ns,
> L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4151
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.2 PCI bridge: Advanced Micro Devices [AMD] Device 43a2 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: f0900000-f09fffff
> Prefetchable memory behind bridge: 00000000f0c00000-00000000f0dfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <64ns,
> L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4159
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.3 PCI bridge: Advanced Micro Devices [AMD] Device 43a3 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: f0500000-f08fffff
> Prefetchable memory behind bridge: 00000000f0100000-00000000f04fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1 <1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet- Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4161
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:16.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b48000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:16.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4b800 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 0 (rev 43)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 1
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 2
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 3
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Capabilities: [f0] Secure device <?>
> Kernel driver in use: k10temp
> ​
> 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 4
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 6
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 5
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 7
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> ​
> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
> Express Gigabit Ethernet controller (rev 06)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 47
> Region 0: I/O ports at 3000 [size=256]
> Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
> Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4189
> Capabilities: [70] Express (v2) Endpoint, MSI 01
> DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 <64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 4096 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
> Vector table: BAR=4 offset=00000000
> PBA: BAR=4 offset=00000800
> Capabilities: [d0] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 3a-0b-00-00-68-4c-e0-00
> Kernel driver in use: r8169
> Kernel modules: r8169
> ​
> 04:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 04) (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at f0a00200 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
> Capabilities: [80] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> unlimited, L1
> unlimited
> ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0 <4us,
> L1 unlimited
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [800 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 05:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE
> 802.11b/g/n WiFi Adapter (rev 01)
> Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at 2000 [size=256]
> Region 2: Memory at f0900000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [70] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <512ns, L1 <64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
> Kernel driver in use: rtl8192ce
> Kernel modules: rtl8192ce
> ​
> ​
> ​
> ​
> ​
> $ lsmod
> Module Size Used by
> rtl8192ce 69655 0
> rtl8192c_common 54535 1 rtl8192ce
> cfbcopyarea 3217 0
> ohci_hcd 20690 0
> sdhci_pci 8440 0
> rtlwifi 87860 1 rtl8192ce
> sdhci 21347 1 sdhci_pci
> cfbimgblt 1969 0
> mmc_core 67307 1 sdhci
> r8169 43238 0
> cfbfillrect 3581 0
> processor 22993 4
> mii 3707 1 r8169
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PROBLEM: Radeon display connector : No monitor connected or invalid EDID
2011-11-13 18:47 ` Dave Airlie
@ 2011-11-13 20:36 ` Alex Deucher
0 siblings, 0 replies; 5+ messages in thread
From: Alex Deucher @ 2011-11-13 20:36 UTC (permalink / raw)
To: Dave Airlie; +Cc: Treeve Jelbert, linux-kernel
On Sun, Nov 13, 2011 at 1:47 PM, Dave Airlie <airlied@gmail.com> wrote:
> cc Alex.
>
>> Since installing kernel-3.1.1 the screen goes blank during the boot and I am
>> unable to do anything, not even ssh into the box.
>> ​
>> linux-3.1.0 worked ok. There are no other changes to the system. Both were
>> built using the same config file.
Can you bisect?
Thanks,
Alex
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PROBLEM: Radeon display connector : No monitor connected or invalid EDID
2011-11-13 17:27 PROBLEM: Radeon display connector : No monitor connected or invalid EDID Treeve Jelbert
2011-11-13 18:47 ` Dave Airlie
@ 2011-11-23 20:37 ` Joseph Salisbury
2011-11-23 22:26 ` Treeve Jelbert
1 sibling, 1 reply; 5+ messages in thread
From: Joseph Salisbury @ 2011-11-23 20:37 UTC (permalink / raw)
To: Treeve Jelbert; +Cc: linux-kernel
On 11/13/2011 12:27 PM, Treeve Jelbert wrote:
> PROBLEM: Radeon display connector : No monitor connected or invalid EDID
> ​
> Since installing kernel-3.1.1 the screen goes blank during the boot and I am
> unable to do anything, not even ssh into the box.
> ​
> linux-3.1.0 worked ok. There are no other changes to the system. Both were
> built using the same config file.
> ​
> When I reboot into 3.1.0 and check the log messages, I see
> ​
> Nov 13 14:31:22 Edge-64 kernel: [ 0.055378] CPU0: AMD A6-3400M APU with
> Radeon(tm) HD Graphics stepping 00
> ​
> # grep '\[drm\]' messages |cut -d: -f4-
> [ 0.645028] [drm] Initialized drm 1.1.0 20060810
> [ 14.128321] [drm] radeon defaulting to kernel modesetting.
> [ 14.128391] [drm] radeon kernel modesetting enabled.
> [ 14.129217] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647
> 0x17AA:0x21EA).
> [ 14.129410] [drm] register mmio base: 0xF0B00000
> [ 14.129476] [drm] register mmio size: 262144
> [ 14.130388] [drm] Detected VRAM RAM=512M, BAR=256M
> [ 14.130459] [drm] RAM width 32bits DDR
> [ 14.130848] [drm] radeon: 512M of VRAM memory ready
> [ 14.130912] [drm] radeon: 512M of GTT memory ready.
> [ 14.131021] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
> [ 14.131085] [drm] Driver supports precise vblank timestamp query.
> [ 14.131281] [drm] radeon: irq initialized.
> [ 14.131347] [drm] GART: num cpu pages 131072, num gpu pages 131072
> [ 14.132538] [drm] Loading SUMO Microcode
> [ 14.547990] [drm] ring test succeeded in 1 usecs
> [ 14.548128] [drm] radeon: ib pool ready.
> [ 14.548249] [drm] ib test succeeded in 0 usecs
> [ 14.551990] [drm] Radeon Display Connectors
> [ 14.552056] [drm] Connector 0:
> [ 14.552119] [drm] VGA
> [ 14.552179] [drm] HPD2
> [ 14.552242] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448
> 0x644c 0x644c
> [ 14.552336] [drm] Encoders:
> [ 14.552397] [drm] CRT1: INTERNAL_UNIPHY2
> [ 14.552473] [drm] CRT1: NUTMEG
> [ 14.552535] [drm] Connector 1:
> [ 14.552596] [drm] LVDS
> [ 14.552657] [drm] HPD1
> [ 14.552718] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438
> 0x643c 0x643c
> [ 14.552809] [drm] Encoders:
> [ 14.552870] [drm] LCD1: INTERNAL_UNIPHY2
> [ 14.552932] [drm] LCD1: TRAVIS
> [ 14.552994] [drm] Connector 2:
> [ 14.553055] [drm] HDMI-A
> [ 14.553115] [drm] HPD3
> [ 14.553176] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458
> 0x645c 0x645c
> [ 14.553266] [drm] Encoders:
> [ 14.553327] [drm] DFP1: INTERNAL_UNIPHY
> [ 14.952397] [drm] Radeon display connector VGA-1: No monitor connected or
> invalid EDID
> [ 15.352332] [drm] Radeon display connector LVDS-1: No monitor connected or
> invalid EDID
> [ 15.752357] [drm] Radeon display connector HDMI-A-1: No monitor connected
> or invalid EDID
> [ 15.779878] [drm] Internal thermal controller without fan control
> [ 15.780236] [drm] radeon: power management initialized
> [ 16.014394] [drm] fb mappable at 0xE0141000
> [ 16.014506] [drm] vram apper at 0xE0000000
> [ 16.014568] [drm] size 4325376
> [ 16.014629] [drm] fb depth is 24
> [ 16.014690] [drm] pitch is 5632
> [ 16.111788] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on
> minor 0
> ​
> at this point the log ends.
> ​
> ​
> I also see
> ​
> [ 13.411889] thinkpad_acpi: Lenovo ThinkPad E525, model 12002JG
> [ 14.129616] ATOM BIOS: Lenovo
> ​
> Those messages did not appear in 3.1.0
> I am not sure of the meaning of ATOM, but I have an AMD system, not Intel.
> ​
> ​
> Keywords:graphics drm radeon Lenovo
> ​
> The following data is from the running linux-3.1.0
> $ lspci -vvv
> ​
> ​
> 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Complex
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 64
> ​
> 00:01.0 VGA compatible controller: ATI Technologies Inc Device 9647 (prog-if
> 00 [VGA controller])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Region 1: I/O ports at 4000 [size=256]
> Region 2: Memory at f0b00000 (32-bit, non-prefetchable) [size=256K]
> Expansion ROM at<unassigned> [disabled]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel modules: radeon
> ​
> 00:01.1 Audio device: ATI Technologies Inc Device 1714
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 46
> Region 0: Memory at f0b44000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI
> 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <4us, L1
> unlimited
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #0, Speed unknown, Width x0, ASPM
> unknown, Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x0, TrErr- Train-
> SlotClk- DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4181
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: snd_hda_intel
> ​
> 00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 12h Processor Root
> Port (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 00003000-00003fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug- Surprise-
> Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet+ LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis+,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4141
> Capabilities: [b0] Subsystem: Lenovo Device 21ea
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:11.0 SATA controller: Advanced Micro Devices [AMD] Hudson SATA Controller
> [AHCI mode] (prog-if 01 [AHCI 1.0])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64
> Interrupt: pin A routed to IRQ 45
> Region 0: I/O ports at 4118 [size=8]
> Region 1: I/O ports at 4124 [size=4]
> Region 2: I/O ports at 4110 [size=8]
> Region 3: I/O ports at 4120 [size=4]
> Region 4: I/O ports at 4100 [size=16]
> Region 5: Memory at f0b4b000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [50] MSI: Enable+ Count=1/16 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4171
> Capabilities: [70] SATA HBA v1.0 InCfgSpace
> Kernel driver in use: ahci
> ​
> 00:12.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b4a000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:12.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4bb00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:13.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b49000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:13.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4ba00 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:14.0 SMBus: Advanced Micro Devices [AMD] Hudson SMBus Controller (rev 13)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller
> (rev 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b40000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: snd_hda_intel
> ​
> 00:14.3 ISA bridge: Advanced Micro Devices [AMD] Hudson LPC Bridge (rev 11)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0
> ​
> 00:14.4 PCI bridge: Advanced Micro Devices [AMD] Hudson PCI Bridge (rev 40)
> (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-
> <MAbort+<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> ​
> 00:14.7 SD Host controller: Advanced Micro Devices [AMD] Hudson SD Flash
> Controller (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 71, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f0b4b900 (32-bit, non-prefetchable) [size=256]
> Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 00:15.0 PCI bridge: Advanced Micro Devices [AMD] Device 43a0 (prog-if 00
> [Normal decode])
> Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4149
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.1 PCI bridge: Advanced Micro Devices [AMD] Device 43a1 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f0a00000-f0afffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort+<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0<64ns,
> L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4151
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.2 PCI bridge: Advanced Micro Devices [AMD] Device 43a2 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: f0900000-f09fffff
> Prefetchable memory behind bridge: 00000000f0c00000-00000000f0dfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0<64ns,
> L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive+
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4159
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:15.3 PCI bridge: Advanced Micro Devices [AMD] Device 43a3 (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
> I/O behind bridge: 00001000-00001fff
> Memory behind bridge: f0500000-f08fffff
> Prefetchable memory behind bridge: 00000000f0100000-00000000f04fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort-<SERR-<PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort->Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <64ns, L1<1us
> ExtTag+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr- TransPend-
> LnkCap: Port #247, Speed 5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <64ns, L1<1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed unknown, Width x16, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd-
> HotPlug+ Surprise-
> Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet-
> CmdCplt- HPIrq-
> LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power-
> Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
> PresDet- Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
> ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
> Selectable De-emphasis: -3.5dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB
> Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4161
> Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1
> Len=010
> <?>
> Kernel driver in use: pcieport
> ​
> 00:16.0 USB controller: Advanced Micro Devices [AMD] Hudson USB OHCI
> Controller (rev 11) (prog-if 10 [OHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f0b48000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci_hcd
> Kernel modules: ohci-hcd
> ​
> 00:16.2 USB controller: Advanced Micro Devices [AMD] Hudson USB EHCI
> Controller (rev 11) (prog-if 20 [EHCI])
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium>TAbort-
> <TAbort-<MAbort->SERR-<PERR- INTx-
> Latency: 64, Cache Line Size: 32 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at f0b4b800 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci_hcd
> ​
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 0 (rev 43)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 1
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 2
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 3
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Capabilities: [f0] Secure device<?>
> Kernel driver in use: k10temp
> ​
> 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 4
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 6
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 5
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor
> Function 7
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> ​
> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI
> Express Gigabit Ethernet controller (rev 06)
> Subsystem: Lenovo Device 21ea
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 47
> Region 0: I/O ports at 3000 [size=256]
> Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
> Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee0f00c Data: 4189
> Capabilities: [70] Express (v2) Endpoint, MSI 01
> DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
> <512ns, L1<64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 4096 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1<64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
> CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
> Vector table: BAR=4 offset=00000000
> PBA: BAR=4 offset=00000800
> Capabilities: [d0] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 3a-0b-00-00-68-4c-e0-00
> Kernel driver in use: r8169
> Kernel modules: r8169
> ​
> 04:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 04) (prog-if 01)
> Subsystem: Lenovo Device 21ea
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at f0a00200 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
> Capabilities: [80] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> unlimited, L1
> unlimited
> ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+
> AuxPwr- TransPend-
> LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0<4us,
> L1 unlimited
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [800 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Kernel driver in use: sdhci-pci
> Kernel modules: sdhci-pci
> ​
> 05:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE
> 802.11b/g/n WiFi Adapter (rev 01)
> Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast>TAbort-
> <TAbort-
> <MAbort->SERR-<PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: I/O ports at 2000 [size=256]
> Region 2: Memory at f0900000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [70] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
> <512ns, L1<64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
> AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
> Latency L0
> <512ns, L1<64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
> Retrain- CommClk+
> ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
> SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> SpeedDis-,
> Selectable De-emphasis: -6dB
> Transmit Margin: Normal Operating Range,
> EnterModifiedCompliance-
> ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> RxOF-
> MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
> UnxCmplt- RxOF+
> MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn-
> ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 01-91-81-fe-ff-4c-e0-00
> Kernel driver in use: rtl8192ce
> Kernel modules: rtl8192ce
> ​
> ​
> ​
> ​
> ​
> $ lsmod
> Module Size Used by
> rtl8192ce 69655 0
> rtl8192c_common 54535 1 rtl8192ce
> cfbcopyarea 3217 0
> ohci_hcd 20690 0
> sdhci_pci 8440 0
> rtlwifi 87860 1 rtl8192ce
> sdhci 21347 1 sdhci_pci
> cfbimgblt 1969 0
> mmc_core 67307 1 sdhci
> r8169 43238 0
> cfbfillrect 3581 0
> processor 22993 4
> mii 3707 1 r8169
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
Hi Treeve,
Have you ever tested the 3.0 kernel on this machine? There is a similar
issue reported[1] for a system equipped with an AMD APU, but that issue
happens on a 3.0.6 kernel.
Thanks,
Joe
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/891968
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: PROBLEM: Radeon display connector : No monitor connected or invalid EDID
2011-11-23 20:37 ` Joseph Salisbury
@ 2011-11-23 22:26 ` Treeve Jelbert
0 siblings, 0 replies; 5+ messages in thread
From: Treeve Jelbert @ 2011-11-23 22:26 UTC (permalink / raw)
To: Joseph Salisbury; +Cc: linux-kernel
On Wednesday 23 November 2011 15:37:07 you wrote:
> Have you ever tested the 3.0 kernel on this machine? There is a similar
> issue reported[1] for a system equipped with an AMD APU, but that issue
> happens on a 3.0.6 kernel.
I tried git-bisect all the way back to 3.0, with the same result
I currently have 3.1.2
If I build the kernel without Radeon KMS support, everything boots
successfully, but Xorg reports that the Radeon driver needs KMS, so reverts to
VESA and then everything is ok.
When I enable KMS, the screen blacks out during the boot process, but I can
login in using ssh
# dmesg |grep drm
[ 4.916467] [drm] Initialized drm 1.1.0 20060810
[ 5.498832] [drm] radeon defaulting to kernel modesetting.
[ 5.498899] [drm] radeon kernel modesetting enabled.
[ 5.676991] [drm] initializing kernel modesetting (SUMO 0x1002:0x9647
0x17AA:0x21EA).
[ 5.677155] [drm] register mmio base: 0xF0B00000
[ 5.677230] [drm] register mmio size: 262144
[ 5.678224] [drm] Detected VRAM RAM=512M, BAR=256M
[ 5.678295] [drm] RAM width 32bits DDR
[ 5.678656] [drm] radeon: 512M of VRAM memory ready
[ 5.678721] [drm] radeon: 512M of GTT memory ready.
[ 5.678800] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 5.678863] [drm] Driver supports precise vblank timestamp query.
[ 5.679080] [drm] radeon: irq initialized.
[ 5.679148] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 5.681874] [drm] Loading SUMO Microcode
[ 6.101298] [drm] ring test succeeded in 1 usecs
[ 6.101477] [drm] radeon: ib pool ready.
[ 6.101605] [drm] ib test succeeded in 0 usecs
[ 6.106994] [drm] Radeon Display Connectors
[ 6.107061] [drm] Connector 0:
[ 6.107123] [drm] VGA
[ 6.107184] [drm] HPD2
[ 6.107305] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c
0x644c
[ 6.107395] [drm] Encoders:
[ 6.107456] [drm] CRT1: INTERNAL_UNIPHY2
[ 6.107517] [drm] CRT1: NUTMEG
[ 6.107579] [drm] Connector 1:
[ 6.107640] [drm] LVDS
[ 6.107700] [drm] HPD1
[ 6.107762] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c
0x643c
[ 6.107851] [drm] Encoders:
[ 6.107912] [drm] LCD1: INTERNAL_UNIPHY2
[ 6.107974] [drm] LCD1: TRAVIS
[ 6.108035] [drm] Connector 2:
[ 6.108096] [drm] HDMI-A
[ 6.108157] [drm] HPD3
[ 6.108264] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458 0x645c
0x645c
[ 6.108358] [drm] Encoders:
[ 6.108421] [drm] DFP1: INTERNAL_UNIPHY
[ 6.505257] [drm] Radeon display connector VGA-1: No monitor connected or
invalid EDID
[ 6.905818] [drm] Radeon display connector LVDS-1: No monitor connected or
invalid EDID
[ 7.305261] [drm] Radeon display connector HDMI-A-1: No monitor connected
or invalid EDID
[ 7.333255] [drm] Internal thermal controller without fan control
[ 7.333639] [drm] radeon: power management initialized
[ 7.584072] [drm] fb mappable at 0xE0141000
[ 7.584188] [drm] vram apper at 0xE0000000
[ 7.584253] [drm] size 4325376
[ 7.584314] [drm] fb depth is 24
[ 7.584376] [drm] pitch is 5632
[ 7.584790] fbcon: radeondrmfb (fb0) is primary device
[ 7.677457] fb0: radeondrmfb frame buffer device
[ 7.677472] drm: registered panic notifier
[ 7.677497] [drm] Initialized radeon 2.11.0 20080528 for 0000:00:01.0 on
minor 0
I am not sure why fb support is enabled, but I could not remove it.
the Xorg.log shows:
[ 16851.295] (II) RADEON(0): Creating default Display subsection in Screen
section
[ 16851.295] (==) RADEON(0): Depth 24, (--) framebuffer bpp 32
[ 16851.295] (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp
pixmaps)
[ 16851.295] (==) RADEON(0): Default visual is TrueColor
[ 16851.295] (==) RADEON(0): RGB weight 888
[ 16851.295] (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
[ 16851.295] (--) RADEON(0): Chipset: "SUMO" (ChipID = 0x9647)
[ 16851.295] (II) RADEON(0): PCIE card detected
[ 16851.309] (II) RADEON(0): KMS Color Tiling: enabled
[ 16851.309] (II) RADEON(0): KMS Pageflipping: enabled
[ 16851.309] (II) RADEON(0): SwapBuffers wait for vsync: enabled
[ 16851.502] (II) RADEON(0): Output VGA-0 has no monitor section
[ 16851.541] (II) RADEON(0): Output LVDS has no monitor section
[ 16851.700] (II) RADEON(0): Output HDMI-0 has no monitor section
[ 16851.892] (II) RADEON(0): EDID for output VGA-0
[ 16851.958] (II) RADEON(0): EDID for output LVDS
[ 16851.958] (II) RADEON(0): Manufacturer: AUO Model: 23ec Serial#: 0
[ 16851.958] (II) RADEON(0): Year: 2009 Week: 1
[ 16851.958] (II) RADEON(0): EDID Version: 1.3
[ 16851.958] (II) RADEON(0): Digital Display Input
[ 16851.958] (II) RADEON(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 16851.958] (II) RADEON(0): Gamma: 2.20
[ 16851.958] (II) RADEON(0): No DPMS capabilities specified
[ 16851.958] (II) RADEON(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 16851.958] (II) RADEON(0): First detailed timing is preferred mode
[ 16851.958] (II) RADEON(0): redX: 0.620 redY: 0.340 greenX: 0.330 greenY:
0.570
[ 16851.958] (II) RADEON(0): blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY:
0.329
[ 16851.958] (II) RADEON(0): Manufacturer's mask: 0
[ 16851.958] (II) RADEON(0): Supported detailed timing:
[ 16851.958] (II) RADEON(0): clock: 69.3 MHz Image Size: 344 x 193 mm
[ 16851.958] (II) RADEON(0): h_active: 1366 h_sync: 1398 h_sync_end 1422
h_blank_end 1432 h_border: 0
[ 16851.958] (II) RADEON(0): v_active: 768 v_sync: 771 v_sync_end 775
v_blanking: 806 v_border: 0
[ 16851.958] (II) RADEON(0): Unknown vendor-specific block f
[ 16851.958] (II) RADEON(0): AUO
[ 16851.958] (II) RADEON(0): B156XW02 V3
[ 16851.958] (II) RADEON(0): EDID (in hex):
[ 16851.958] (II) RADEON(0): 00ffffffffffff0006afec2300000000
[ 16851.958] (II) RADEON(0): 01130103802213780ac8959e57549226
[ 16851.958] (II) RADEON(0): 0f505400000001010101010101010101
[ 16851.958] (II) RADEON(0): 010101010101121b5642500026302018
[ 16851.958] (II) RADEON(0): 340058c1100000180000000f00000000
[ 16851.958] (II) RADEON(0): 00000000000000000020000000fe0041
[ 16851.958] (II) RADEON(0): 554f0a202020202020202020000000fe
[ 16851.958] (II) RADEON(0): 004231353658573032205633200a00be
[ 16851.958] (II) RADEON(0): Printing probed modes for output LVDS
[ 16851.958] (II) RADEON(0): Modeline "1366x768"x60.0 69.30 1366 1398 1422
1432 768 771 775 806 -hsync -vsync (48.4 kHz)
[ 16851.958] (II) RADEON(0): Modeline "1280x720"x59.9 74.50 1280 1344 1472
1664 720 723 728 748 -hsync +vsync (44.8 kHz)
[ 16851.958] (II) RADEON(0): Modeline "1152x768"x59.8 71.75 1152 1216 1328
1504 768 771 781 798 -hsync +vsync (47.7 kHz)
[ 16851.958] (II) RADEON(0): Modeline "1024x768"x59.9 63.50 1024 1072 1176
1328 768 771 775 798 -hsync +vsync (47.8 kHz)
[ 16851.958] (II) RADEON(0): Modeline "800x600"x59.9 38.25 800 832 912 1024
600 603 607 624 -hsync +vsync (37.4 kHz)
[ 16851.958] (II) RADEON(0): Modeline "848x480"x59.7 31.50 848 872 952 1056
480 483 493 500 -hsync +vsync (29.8 kHz)
[ 16851.958] (II) RADEON(0): Modeline "720x480"x59.7 26.75 720 744 808 896
480 483 493 500 -hsync +vsync (29.9 kHz)
[ 16851.958] (II) RADEON(0): Modeline "640x480"x59.4 23.75 640 664 720 800
480 483 487 500 -hsync +vsync (29.7 kHz)
[ 16852.116] (II) RADEON(0): EDID for output HDMI-0
[ 16852.116] (II) RADEON(0): Output VGA-0 disconnected
[ 16852.116] (II) RADEON(0): Output LVDS connected
[ 16852.116] (II) RADEON(0): Output HDMI-0 disconnected
[ 16852.116] (II) RADEON(0): Using exact sizes for initial modes
[ 16852.116] (II) RADEON(0): Output LVDS using initial mode 1366x768
[ 16852.116] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless
otherwise stated.
[ 16852.116] (II) RADEON(0): mem size init: gart size :1fdff000 vram size:
s:20000000 visible:fba0000
[ 16852.116] (II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM
[ 16852.116] (==) RADEON(0): DPI set to (96, 96)
[ 16852.149] (II) RADEON(0): [DRI2] Setup complete
[ 16852.149] (II) RADEON(0): [DRI2] DRI driver: r600
[ 16852.149] (II) RADEON(0): [DRI2] VDPAU driver: r600
[ 16852.149] (II) RADEON(0): Front buffer size: 4224K
[ 16852.149] (II) RADEON(0): VRAM usage limit set to 228096K
[ 16852.153] (==) RADEON(0): Backing store disabled
[ 16852.153] (II) RADEON(0): Direct rendering enabled
[ 16852.167] (II) RADEON(0): Setting EXA maxPitchBytes
[ 16852.168] (II) RADEON(0): Acceleration enabled
[ 16852.168] (==) RADEON(0): DPMS enabled
[ 16852.168] (==) RADEON(0): Silken mouse enabled
[ 16852.197] (II) RADEON(0): Set up textured video
[ 16852.197] (II) RADEON(0): [XvMC] Associated with Radeon Textured Video.
[ 16852.197] (II) RADEON(0): [XvMC] Extension initialized.
[ 16852.197] (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR
disabled message.
[ 16852.617] (II) RADEON(0): Setting screen physical size to 361 x 203
but the screen is still black
Regards, Treeve
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2011-11-23 22:26 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-13 17:27 PROBLEM: Radeon display connector : No monitor connected or invalid EDID Treeve Jelbert
2011-11-13 18:47 ` Dave Airlie
2011-11-13 20:36 ` Alex Deucher
2011-11-23 20:37 ` Joseph Salisbury
2011-11-23 22:26 ` Treeve Jelbert
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox