* Patch for ide/pdc202xx.c
@ 2002-03-28 17:27 Markus Sinner
0 siblings, 0 replies; only message in thread
From: Markus Sinner @ 2002-03-28 17:27 UTC (permalink / raw)
To: andre; +Cc: linux-kernel, promise, Bernd Herd
[-- Attachment #1: Type: text/plain, Size: 1161 bytes --]
Hi Maintainers,
i've added support for promise PDC 20276 Chipset, based on Gigabyte
GA-7DXR+. With the supported changes the driver works fine in DMA(33)
Mode, what in my System means about 22MB/sec. I'd be pleased if you
include these changes in pre5 or so.
I also tried to get U-DMA-100 worked, but that hacking. I manually set
UDMA in an ugly way, but it works and both of my 120GB HDDs get transfers:
/dev/hda:
Timing buffered disk reads: 64 MB in 1.40 seconds = 45.71 MB/sec
And that would be ok!
My system is configured with raid0 and raid1 (linux-software-)RAID and
is works stable since about two weeks. So maybe some little changes have
to be maid to pdc202xx.c to work correctly, but I'm not quite good
enough to understand whats going on on the chip. Maybe with a little
help of you I can get it worked correctly. I perhaps could configure an
hardisk for root-access over ISDN or Internet, just for trying ;-)
:-) Markus Sinner
--
*********************************
sinner@psitronic.de
http://www.psitronic.de
psitronic IT-Solutions
Markus Sinner
Lindenstraße 5 - 68642 Bürstadt
Tel.: (+49)6206 / 963513
Fax: (+49)6206 / 963514
[-- Attachment #2: diff --]
[-- Type: application/x-java-vm, Size: 5099 bytes --]
[-- Attachment #3: pdc202xx.c --]
[-- Type: text/x-csrc, Size: 41863 bytes --]
/*
* linux/drivers/ide/pdc202xx.c Version 0.30 Mar. 18, 2000
*
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
* May be copied or modified under the terms of the GNU General Public License
*
* Promise Ultra33 cards with BIOS v1.20 through 1.28 will need this
* compiled into the kernel if you have more than one card installed.
* Note that BIOS v1.29 is reported to fix the problem. Since this is
* safe chipset tuning, including this support is harmless
*
* Promise Ultra66 cards with BIOS v1.11 this
* compiled into the kernel if you have more than one card installed.
*
* Promise Ultra100 cards.
*
* The latest chipset code will support the following ::
* Three Ultra33 controllers and 12 drives.
* 8 are UDMA supported and 4 are limited to DMA mode 2 multi-word.
* The 8/4 ratio is a BIOS code limit by promise.
*
* UNLESS you enable "CONFIG_PDC202XX_BURST"
*
*/
/*
* Portions Copyright (C) 1999 Promise Technology, Inc.
* Author: Frank Tiernan (frankt@promise.com)
* Released under terms of General Public License
*/
#include <linux/config.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/hdreg.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/ide.h>
#include <asm/io.h>
#include <asm/irq.h>
#include "ide_modes.h"
#define PDC202XX_DEBUG_DRIVE_INFO 0
#define PDC202XX_DECODE_REGISTER_INFO 0
#define DISPLAY_PDC202XX_TIMINGS
#ifndef SPLIT_BYTE
#define SPLIT_BYTE(B,H,L) ((H)=(B>>4), (L)=(B-((B>>4)<<4)))
#endif
#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS)
#include <linux/stat.h>
#include <linux/proc_fs.h>
static int pdc202xx_get_info(char *, char **, off_t, int);
extern int (*pdc202xx_display_info)(char *, char **, off_t, int); /* ide-proc.c */
extern char *ide_media_verbose(ide_drive_t *);
static struct pci_dev *bmide_dev;
char *pdc202xx_pio_verbose (u32 drive_pci)
{
if ((drive_pci & 0x000ff000) == 0x000ff000) return("NOTSET");
if ((drive_pci & 0x00000401) == 0x00000401) return("PIO 4");
if ((drive_pci & 0x00000602) == 0x00000602) return("PIO 3");
if ((drive_pci & 0x00000803) == 0x00000803) return("PIO 2");
if ((drive_pci & 0x00000C05) == 0x00000C05) return("PIO 1");
if ((drive_pci & 0x00001309) == 0x00001309) return("PIO 0");
return("PIO ?");
}
char *pdc202xx_dma_verbose (u32 drive_pci)
{
if ((drive_pci & 0x00036000) == 0x00036000) return("MWDMA 2");
if ((drive_pci & 0x00046000) == 0x00046000) return("MWDMA 1");
if ((drive_pci & 0x00056000) == 0x00056000) return("MWDMA 0");
if ((drive_pci & 0x00056000) == 0x00056000) return("SWDMA 2");
if ((drive_pci & 0x00068000) == 0x00068000) return("SWDMA 1");
if ((drive_pci & 0x000BC000) == 0x000BC000) return("SWDMA 0");
return("PIO---");
}
char *pdc202xx_ultra_verbose (u32 drive_pci, u16 slow_cable)
{
if ((drive_pci & 0x000ff000) == 0x000ff000)
return("NOTSET");
/** CHANGED >>>> **/
if ((drive_pci & 0x00006000) == 0x00006000)
return((slow_cable) ? "UDMA ?" : "UDMA 5");
/** CHANGED <<<< **/
printk("SINNER: drivepci %0x slowcable %0x\n", drive_pci);
if ((drive_pci & 0x00012000) == 0x00012000)
return((slow_cable) ? "UDMA 2" : "UDMA 4");
if ((drive_pci & 0x00024000) == 0x00024000)
return((slow_cable) ? "UDMA 1" : "UDMA 3");
if ((drive_pci & 0x00036000) == 0x00036000)
return("UDMA 0");
return(pdc202xx_dma_verbose(drive_pci));
}
static char * pdc202xx_info (char *buf, struct pci_dev *dev)
{
char *p = buf;
u32 bibma = pci_resource_start(dev, 4);
u32 reg60h = 0, reg64h = 0, reg68h = 0, reg6ch = 0;
u16 reg50h = 0, pmask = (1<<10), smask = (1<<11);
u8 hi = 0, lo = 0;
/*
* at that point bibma+0x2 et bibma+0xa are byte registers
* to investigate:
*/
u8 c0 = inb_p((unsigned short)bibma + 0x02);
u8 c1 = inb_p((unsigned short)bibma + 0x0a);
u8 sc11 = inb_p((unsigned short)bibma + 0x11);
u8 sc1a = inb_p((unsigned short)bibma + 0x1a);
u8 sc1b = inb_p((unsigned short)bibma + 0x1b);
u8 sc1c = inb_p((unsigned short)bibma + 0x1c);
u8 sc1d = inb_p((unsigned short)bibma + 0x1d);
u8 sc1e = inb_p((unsigned short)bibma + 0x1e);
u8 sc1f = inb_p((unsigned short)bibma + 0x1f);
pci_read_config_word(dev, 0x50, ®50h);
pci_read_config_dword(dev, 0x60, ®60h);
pci_read_config_dword(dev, 0x64, ®64h);
pci_read_config_dword(dev, 0x68, ®68h);
pci_read_config_dword(dev, 0x6c, ®6ch);
switch(dev->device) {
case PCI_DEVICE_ID_PROMISE_20267:
p += sprintf(p, "\n PDC20267 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20265:
p += sprintf(p, "\n PDC20265 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20262:
p += sprintf(p, "\n PDC20262 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20246:
p += sprintf(p, "\n PDC20246 Chipset.\n");
reg50h |= 0x0c00;
break;
default:
p += sprintf(p, "\n PDC202XX Chipset.\n");
break;
}
p += sprintf(p, "------------------------------- General Status ---------------------------------\n");
p += sprintf(p, "Burst Mode : %sabled\n", (sc1f & 0x01) ? "en" : "dis");
p += sprintf(p, "Host Mode : %s\n", (sc1f & 0x08) ? "Tri-Stated" : "Normal");
p += sprintf(p, "Bus Clocking : %s\n",
((sc1f & 0xC0) == 0xC0) ? "100 External" :
((sc1f & 0x80) == 0x80) ? "66 External" :
((sc1f & 0x40) == 0x40) ? "33 External" : "33 PCI Internal");
p += sprintf(p, "IO pad select : %s mA\n",
((sc1c & 0x03) == 0x03) ? "10" :
((sc1c & 0x02) == 0x02) ? "8" :
((sc1c & 0x01) == 0x01) ? "6" :
((sc1c & 0x00) == 0x00) ? "4" : "??");
SPLIT_BYTE(sc1e, hi, lo);
p += sprintf(p, "Status Polling Period : %d\n", hi);
p += sprintf(p, "Interrupt Check Status Polling Delay : %d\n", lo);
p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n");
p += sprintf(p, " %s %s\n",
(c0&0x80)?"disabled":"enabled ",
(c1&0x80)?"disabled":"enabled ");
p += sprintf(p, "66 Clocking %s %s\n",
(sc11&0x02)?"enabled ":"disabled",
(sc11&0x08)?"enabled ":"disabled");
p += sprintf(p, " Mode %s Mode %s\n",
(sc1a & 0x01) ? "MASTER" : "PCI ",
(sc1b & 0x01) ? "MASTER" : "PCI ");
p += sprintf(p, " %s %s\n",
(sc1d & 0x08) ? "Error " :
((sc1d & 0x05) == 0x05) ? "Not My INTR " :
(sc1d & 0x04) ? "Interrupting" :
(sc1d & 0x02) ? "FIFO Full " :
(sc1d & 0x01) ? "FIFO Empty " : "????????????",
(sc1d & 0x80) ? "Error " :
((sc1d & 0x50) == 0x50) ? "Not My INTR " :
(sc1d & 0x40) ? "Interrupting" :
(sc1d & 0x20) ? "FIFO Full " :
(sc1d & 0x10) ? "FIFO Empty " : "????????????");
p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n");
p += sprintf(p, "DMA enabled: %s %s %s %s\n",
(c0&0x20)?"yes":"no ",(c0&0x40)?"yes":"no ",(c1&0x20)?"yes":"no ",(c1&0x40)?"yes":"no ");
p += sprintf(p, "DMA Mode: %s %s %s %s\n",
pdc202xx_ultra_verbose(reg60h, (reg50h & pmask)),
pdc202xx_ultra_verbose(reg64h, (reg50h & pmask)),
pdc202xx_ultra_verbose(reg68h, (reg50h & smask)),
pdc202xx_ultra_verbose(reg6ch, (reg50h & smask)));
p += sprintf(p, "PIO Mode: %s %s %s %s\n",
pdc202xx_pio_verbose(reg60h),
pdc202xx_pio_verbose(reg64h),
pdc202xx_pio_verbose(reg68h),
pdc202xx_pio_verbose(reg6ch));
#if 0
p += sprintf(p, "--------------- Can ATAPI DMA ---------------\n");
#endif
return (char *)p;
}
static char * pdc202xx_info_new (char *buf, struct pci_dev *dev)
{
char *p = buf;
// u32 bibma = pci_resource_start(dev, 4);
// u32 reg60h = 0, reg64h = 0, reg68h = 0, reg6ch = 0;
// u16 reg50h = 0, word88 = 0;
// int udmasel[4]={0,0,0,0}, piosel[4]={0,0,0,0}, i=0, hd=0;
switch(dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
p += sprintf(p, "\n PDC20276 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20275:
p += sprintf(p, "\n PDC20275 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20269:
p += sprintf(p, "\n PDC20269 TX2 Chipset.\n");
break;
case PCI_DEVICE_ID_PROMISE_20268:
case PCI_DEVICE_ID_PROMISE_20268R:
p += sprintf(p, "\n PDC20268 TX2 Chipset.\n");
break;
default:
p += sprintf(p, "\n PDC202XX Chipset.\n");
break;
}
return (char *)p;
}
static int pdc202xx_get_info (char *buffer, char **addr, off_t offset, int count)
{
char *p = buffer;
switch(bmide_dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
p = pdc202xx_info_new(buffer, bmide_dev);
p = pdc202xx_info(buffer, bmide_dev);
break;
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
case PCI_DEVICE_ID_PROMISE_20268:
case PCI_DEVICE_ID_PROMISE_20268R:
p = pdc202xx_info_new(buffer, bmide_dev);
break;
default:
p = pdc202xx_info(buffer, bmide_dev);
break;
}
return p-buffer; /* => must be less than 4k! */
}
#endif /* defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) */
byte pdc202xx_proc = 0;
const char *pdc_quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
"QUANTUM FIREBALLP KA6.4",
"QUANTUM FIREBALLP LM20.4",
"QUANTUM FIREBALLP KX20.5",
"QUANTUM FIREBALLP KX27.3",
"QUANTUM FIREBALLP LM20.5",
NULL
};
extern char *ide_xfer_verbose (byte xfer_rate);
/* A Register */
#define SYNC_ERRDY_EN 0xC0
#define SYNC_IN 0x80 /* control bit, different for master vs. slave drives */
#define ERRDY_EN 0x40 /* control bit, different for master vs. slave drives */
#define IORDY_EN 0x20 /* PIO: IOREADY */
#define PREFETCH_EN 0x10 /* PIO: PREFETCH */
#define PA3 0x08 /* PIO"A" timing */
#define PA2 0x04 /* PIO"A" timing */
#define PA1 0x02 /* PIO"A" timing */
#define PA0 0x01 /* PIO"A" timing */
/* B Register */
#define MB2 0x80 /* DMA"B" timing */
#define MB1 0x40 /* DMA"B" timing */
#define MB0 0x20 /* DMA"B" timing */
#define PB4 0x10 /* PIO_FORCE 1:0 */
#define PB3 0x08 /* PIO"B" timing */ /* PIO flow Control mode */
#define PB2 0x04 /* PIO"B" timing */ /* PIO 4 */
#define PB1 0x02 /* PIO"B" timing */ /* PIO 3 half */
#define PB0 0x01 /* PIO"B" timing */ /* PIO 3 other half */
/* C Register */
#define IORDYp_NO_SPEED 0x4F
#define SPEED_DIS 0x0F
#define DMARQp 0x80
#define IORDYp 0x40
#define DMAR_EN 0x20
#define DMAW_EN 0x10
#define MC3 0x08 /* DMA"C" timing */
#define MC2 0x04 /* DMA"C" timing */
#define MC1 0x02 /* DMA"C" timing */
#define MC0 0x01 /* DMA"C" timing */
#if PDC202XX_DECODE_REGISTER_INFO
#define REG_A 0x01
#define REG_B 0x02
#define REG_C 0x04
#define REG_D 0x08
static void decode_registers (byte registers, byte value)
{
byte bit = 0, bit1 = 0, bit2 = 0;
switch(registers) {
case REG_A:
bit2 = 0;
printk("A Register ");
if (value & 0x80) printk("SYNC_IN ");
if (value & 0x40) printk("ERRDY_EN ");
if (value & 0x20) printk("IORDY_EN ");
if (value & 0x10) printk("PREFETCH_EN ");
if (value & 0x08) { printk("PA3 ");bit2 |= 0x08; }
if (value & 0x04) { printk("PA2 ");bit2 |= 0x04; }
if (value & 0x02) { printk("PA1 ");bit2 |= 0x02; }
if (value & 0x01) { printk("PA0 ");bit2 |= 0x01; }
printk("PIO(A) = %d ", bit2);
break;
case REG_B:
bit1 = 0;bit2 = 0;
printk("B Register ");
if (value & 0x80) { printk("MB2 ");bit1 |= 0x80; }
if (value & 0x40) { printk("MB1 ");bit1 |= 0x40; }
if (value & 0x20) { printk("MB0 ");bit1 |= 0x20; }
printk("DMA(B) = %d ", bit1 >> 5);
if (value & 0x10) printk("PIO_FORCED/PB4 ");
if (value & 0x08) { printk("PB3 ");bit2 |= 0x08; }
if (value & 0x04) { printk("PB2 ");bit2 |= 0x04; }
if (value & 0x02) { printk("PB1 ");bit2 |= 0x02; }
if (value & 0x01) { printk("PB0 ");bit2 |= 0x01; }
printk("PIO(B) = %d ", bit2);
break;
case REG_C:
bit2 = 0;
printk("C Register ");
if (value & 0x80) printk("DMARQp ");
if (value & 0x40) printk("IORDYp ");
if (value & 0x20) printk("DMAR_EN ");
if (value & 0x10) printk("DMAW_EN ");
if (value & 0x08) { printk("MC3 ");bit2 |= 0x08; }
if (value & 0x04) { printk("MC2 ");bit2 |= 0x04; }
if (value & 0x02) { printk("MC1 ");bit2 |= 0x02; }
if (value & 0x01) { printk("MC0 ");bit2 |= 0x01; }
printk("DMA(C) = %d ", bit2);
break;
case REG_D:
printk("D Register ");
break;
default:
return;
}
printk("\n %s ", (registers & REG_D) ? "DP" :
(registers & REG_C) ? "CP" :
(registers & REG_B) ? "BP" :
(registers & REG_A) ? "AP" : "ERROR");
for (bit=128;bit>0;bit/=2)
printk("%s", (value & bit) ? "1" : "0");
printk("\n");
}
#endif /* PDC202XX_DECODE_REGISTER_INFO */
static int check_in_drive_lists (ide_drive_t *drive, const char **list)
{
struct hd_driveid *id = drive->id;
if (pdc_quirk_drives == list) {
while (*list) {
if (strstr(id->model, *list++)) {
return 2;
}
}
} else {
while (*list) {
if (!strcmp(*list++,id->model)) {
return 1;
}
}
}
return 0;
}
static int pdc202xx_tune_chipset (ide_drive_t *drive, byte speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
unsigned int drive_conf;
int err;
byte drive_pci, AP, BP, CP, DP;
byte TA = 0, TB = 0, TC = 0;
switch (drive->dn) {
case 0: drive_pci = 0x60; break;
case 1: drive_pci = 0x64; break;
case 2: drive_pci = 0x68; break;
case 3: drive_pci = 0x6c; break;
default: return -1;
}
if ((drive->media != ide_disk) && (speed < XFER_SW_DMA_0)) return -1;
pci_read_config_dword(dev, drive_pci, &drive_conf);
pci_read_config_byte(dev, (drive_pci), &AP);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0) {
if ((BP & 0xF0) && (CP & 0x0F)) {
/* clear DMA modes of upper 842 bits of B Register */
/* clear PIO forced mode upper 1 bit of B Register */
pci_write_config_byte(dev, (drive_pci)|0x01, BP & ~0xF0);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
/* clear DMA modes of lower 8421 bits of C Register */
pci_write_config_byte(dev, (drive_pci)|0x02, CP & ~0x0F);
pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
}
} else {
#else
{
#endif /* CONFIG_BLK_DEV_IDEDMA */
if ((AP & 0x0F) || (BP & 0x07)) {
/* clear PIO modes of lower 8421 bits of A Register */
pci_write_config_byte(dev, (drive_pci), AP & ~0x0F);
pci_read_config_byte(dev, (drive_pci), &AP);
/* clear PIO modes of lower 421 bits of B Register */
pci_write_config_byte(dev, (drive_pci)|0x01, BP & ~0x07);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
pci_read_config_byte(dev, (drive_pci), &AP);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
}
}
pci_read_config_byte(dev, (drive_pci), &AP);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
switch(speed) {
#ifdef CONFIG_BLK_DEV_IDEDMA
/* case XFER_UDMA_6: */
case XFER_UDMA_5:
case XFER_UDMA_4: TB = 0x20; TC = 0x01; break; /* speed 8 == UDMA mode 4 */
case XFER_UDMA_3: TB = 0x40; TC = 0x02; break; /* speed 7 == UDMA mode 3 */
case XFER_UDMA_2: TB = 0x20; TC = 0x01; break; /* speed 6 == UDMA mode 2 */
case XFER_UDMA_1: TB = 0x40; TC = 0x02; break; /* speed 5 == UDMA mode 1 */
case XFER_UDMA_0: TB = 0x60; TC = 0x03; break; /* speed 4 == UDMA mode 0 */
case XFER_MW_DMA_2: TB = 0x60; TC = 0x03; break; /* speed 4 == MDMA mode 2 */
case XFER_MW_DMA_1: TB = 0x60; TC = 0x04; break; /* speed 3 == MDMA mode 1 */
case XFER_MW_DMA_0: TB = 0x60; TC = 0x05; break; /* speed 2 == MDMA mode 0 */
case XFER_SW_DMA_2: TB = 0x60; TC = 0x05; break; /* speed 0 == SDMA mode 2 */
case XFER_SW_DMA_1: TB = 0x80; TC = 0x06; break; /* speed 1 == SDMA mode 1 */
case XFER_SW_DMA_0: TB = 0xC0; TC = 0x0B; break; /* speed 0 == SDMA mode 0 */
#endif /* CONFIG_BLK_DEV_IDEDMA */
case XFER_PIO_4: TA = 0x01; TB = 0x04; break;
case XFER_PIO_3: TA = 0x02; TB = 0x06; break;
case XFER_PIO_2: TA = 0x03; TB = 0x08; break;
case XFER_PIO_1: TA = 0x05; TB = 0x0C; break;
case XFER_PIO_0:
default: TA = 0x09; TB = 0x13; break;
}
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0) {
pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
pci_write_config_byte(dev, (drive_pci)|0x02, CP|TC);
} else {
#else
{
#endif /* CONFIG_BLK_DEV_IDEDMA */
pci_write_config_byte(dev, (drive_pci), AP|TA);
pci_write_config_byte(dev, (drive_pci)|0x01, BP|TB);
}
#if PDC202XX_DECODE_REGISTER_INFO
pci_read_config_byte(dev, (drive_pci), &AP);
pci_read_config_byte(dev, (drive_pci)|0x01, &BP);
pci_read_config_byte(dev, (drive_pci)|0x02, &CP);
pci_read_config_byte(dev, (drive_pci)|0x03, &DP);
decode_registers(REG_A, AP);
decode_registers(REG_B, BP);
decode_registers(REG_C, CP);
decode_registers(REG_D, DP);
#endif /* PDC202XX_DECODE_REGISTER_INFO */
if (!drive->init_speed)
drive->init_speed = speed;
err = ide_config_drive_speed(drive, speed);
drive->current_speed = speed;
#if PDC202XX_DEBUG_DRIVE_INFO
printk("%s: %s drive%d 0x%08x ",
drive->name, ide_xfer_verbose(speed),
drive->dn, drive_conf);
pci_read_config_dword(dev, drive_pci, &drive_conf);
printk("0x%08x\n", drive_conf);
#endif /* PDC202XX_DEBUG_DRIVE_INFO */
return err;
}
static int pdc202xx_new_tune_chipset (ide_drive_t *drive, byte speed)
{
ide_hwif_t *hwif = HWIF(drive);
#ifdef CONFIG_BLK_DEV_IDEDMA
unsigned long indexreg = (hwif->dma_base + 1);
unsigned long datareg = (hwif->dma_base + 3);
#else
struct pci_dev *dev = hwif->pci_dev;
unsigned long high_16 = pci_resource_start(dev, 4);
unsigned long indexreg = high_16 + (hwif->channel ? 0x09 : 0x01);
unsigned long datareg = (indexreg + 2);
#endif /* CONFIG_BLK_DEV_IDEDMA */
byte thold = 0x10;
byte adj = (drive->dn%2) ? 0x08 : 0x00;
int err;
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed == XFER_UDMA_2) {
OUT_BYTE((thold + adj), indexreg);
OUT_BYTE((IN_BYTE(datareg) & 0x7f), datareg);
}
switch (speed) {
case XFER_UDMA_7:
speed = XFER_UDMA_6;
case XFER_UDMA_6:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x1a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x01, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xcb, datareg);
break;
case XFER_UDMA_5:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x1a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x02, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xcb, datareg);
break;
case XFER_UDMA_4:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x1a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x03, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xcd, datareg);
break;
case XFER_UDMA_3:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x1a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x05, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xcd, datareg);
break;
case XFER_UDMA_2:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x2a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x07, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xcd, datareg);
break;
case XFER_UDMA_1:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x3a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x0a, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xd0, datareg);
break;
case XFER_UDMA_0:
OUT_BYTE((0x10 + adj), indexreg);
OUT_BYTE(0x4a, datareg);
OUT_BYTE((0x11 + adj), indexreg);
OUT_BYTE(0x0f, datareg);
OUT_BYTE((0x12 + adj), indexreg);
OUT_BYTE(0xd5, datareg);
break;
case XFER_MW_DMA_2:
OUT_BYTE((0x0e + adj), indexreg);
OUT_BYTE(0x69, datareg);
OUT_BYTE((0x0f + adj), indexreg);
OUT_BYTE(0x25, datareg);
break;
case XFER_MW_DMA_1:
OUT_BYTE((0x0e + adj), indexreg);
OUT_BYTE(0x6b, datareg);
OUT_BYTE((0x0f+ adj), indexreg);
OUT_BYTE(0x27, datareg);
break;
case XFER_MW_DMA_0:
OUT_BYTE((0x0e + adj), indexreg);
OUT_BYTE(0xdf, datareg);
OUT_BYTE((0x0f + adj), indexreg);
OUT_BYTE(0x5f, datareg);
break;
#else
switch (speed) {
#endif /* CONFIG_BLK_DEV_IDEDMA */
case XFER_PIO_4:
OUT_BYTE((0x0c + adj), indexreg);
OUT_BYTE(0x23, datareg);
OUT_BYTE((0x0d + adj), indexreg);
OUT_BYTE(0x09, datareg);
OUT_BYTE((0x13 + adj), indexreg);
OUT_BYTE(0x25, datareg);
break;
case XFER_PIO_3:
OUT_BYTE((0x0c + adj), indexreg);
OUT_BYTE(0x27, datareg);
OUT_BYTE((0x0d + adj), indexreg);
OUT_BYTE(0x0d, datareg);
OUT_BYTE((0x13 + adj), indexreg);
OUT_BYTE(0x35, datareg);
break;
case XFER_PIO_2:
OUT_BYTE((0x0c + adj), indexreg);
OUT_BYTE(0x23, datareg);
OUT_BYTE((0x0d + adj), indexreg);
OUT_BYTE(0x26, datareg);
OUT_BYTE((0x13 + adj), indexreg);
OUT_BYTE(0x64, datareg);
break;
case XFER_PIO_1:
OUT_BYTE((0x0c + adj), indexreg);
OUT_BYTE(0x46, datareg);
OUT_BYTE((0x0d + adj), indexreg);
OUT_BYTE(0x29, datareg);
OUT_BYTE((0x13 + adj), indexreg);
OUT_BYTE(0xa4, datareg);
break;
case XFER_PIO_0:
OUT_BYTE((0x0c + adj), indexreg);
OUT_BYTE(0xfb, datareg);
OUT_BYTE((0x0d + adj), indexreg);
OUT_BYTE(0x2b, datareg);
OUT_BYTE((0x13 + adj), indexreg);
OUT_BYTE(0xac, datareg);
break;
default:
}
if (!drive->init_speed)
drive->init_speed = speed;
err = ide_config_drive_speed(drive, speed);
drive->current_speed = speed;
return err;
}
/* 0 1 2 3 4 5 6 7 8
* 960, 480, 390, 300, 240, 180, 120, 90, 60
* 180, 150, 120, 90, 60
* DMA_Speed
* 180, 120, 90, 90, 90, 60, 30
* 11, 5, 4, 3, 2, 1, 0
*/
static int config_chipset_for_pio (ide_drive_t *drive, byte pio)
{
byte speed = 0x00;
pio = (pio == 5) ? 4 : pio;
speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, pio, NULL);
return ((int) pdc202xx_tune_chipset(drive, speed));
}
static void pdc202xx_tune_drive (ide_drive_t *drive, byte pio)
{
(void) config_chipset_for_pio(drive, pio);
}
#ifdef CONFIG_BLK_DEV_IDEDMA
static int config_chipset_for_dma (ide_drive_t *drive, byte ultra)
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
unsigned long high_16 = pci_resource_start(dev, 4);
unsigned long dma_base = hwif->dma_base;
unsigned long indexreg = dma_base + 1;
unsigned long datareg = dma_base + 3;
byte iordy = 0x13;
byte adj = (drive->dn%2) ? 0x08 : 0x00;
byte cable = 0;
byte jumpbit = 0;
byte unit = (drive->select.b.unit & 0x01);
unsigned int drive_conf;
byte drive_pci = 0;
byte test1, test2, speed = -1;
byte AP;
unsigned short EP;
byte CLKSPD = 0;
byte udma_33 = ultra;
// byte udma_33 = ultra ? (IN_BYTE(high_16 + 0x001f) & 1) : 0;
byte udma_66 = ((eighty_ninty_three(drive)) && udma_33) ? 1 : 0;
byte udma_100 = 0;
byte udma_133 = 0;
byte mask = hwif->channel ? 0x08 : 0x02;
unsigned short c_mask = hwif->channel ? (1<<11) : (1<<10);
byte ultra_66 = ((id->dma_ultra & 0x0010) ||
(id->dma_ultra & 0x0008)) ? 1 : 0;
byte ultra_100 = ((id->dma_ultra & 0x0020) ||
(ultra_66)) ? 1 : 0;
byte ultra_133 = ((id->dma_ultra & 0x0040) ||
(ultra_100)) ? 1 : 0;
switch(dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
udma_133 = (udma_66) ? 1 : 0;
udma_100 = (udma_66) ? 1 : 0;
OUT_BYTE(0x0b, (hwif->dma_base + 1));
cable = ((IN_BYTE((hwif->dma_base + 3)) & 0x04));
jumpbit = 1;
printk("PROMISE_20276 BUGGY SINNER SETTING UDMA100!\n");
udma_66 = udma_100 = 1;
cable = 0;
/** CHANGED >>>> **/
if (udma_100)
printk("UDMA 100 ");
else
printk("NO-UDMA 100 ");
if (udma_133)
printk("UDMA 133 ");
else
printk("NO-UDMA 133 ");
if (!cable)
printk("CABLE KONTUKTER\n");
else
printk("CABLE NORMAL\n");
/** CHANGED <<<< **/
break;
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
udma_133 = (udma_66) ? 1 : 0;
udma_100 = (udma_66) ? 1 : 0;
OUT_BYTE(0x0b, (hwif->dma_base + 1));
cable = ((IN_BYTE((hwif->dma_base + 3)) & 0x04));
jumpbit = 1;
break;
case PCI_DEVICE_ID_PROMISE_20268R:
udma_100 = 1;
udma_66 = 1;
OUT_BYTE(0x0b, (hwif->dma_base + 1));
cable = ((IN_BYTE((hwif->dma_base + 3)) & 0x04));
jumpbit = 1;
break;
case PCI_DEVICE_ID_PROMISE_20268:
udma_100 = (udma_66) ? 1 : 0;
OUT_BYTE(0x0b, (hwif->dma_base + 1));
cable = ((IN_BYTE((hwif->dma_base + 3)) & 0x04));
jumpbit = 1;
break;
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
udma_100 = (udma_66) ? 1 : 0;
pci_read_config_word(dev, 0x50, &EP);
cable = (EP & c_mask);
jumpbit = 0;
break;
case PCI_DEVICE_ID_PROMISE_20262:
pci_read_config_word(dev, 0x50, &EP);
cable = (EP & c_mask);
jumpbit = 0;
break;
default:
udma_100 = 0; udma_133 = 0; cable = 1; jumpbit = 0;
break;
}
if (!jumpbit)
CLKSPD = IN_BYTE(high_16 + 0x11);
/*
* Set the control register to use the 66Mhz system
* clock for UDMA 3/4 mode operation. If one drive on
* a channel is U66 capable but the other isn't we
* fall back to U33 mode. The BIOS INT 13 hooks turn
* the clock on then off for each read/write issued. I don't
* do that here because it would require modifying the
* kernel, seperating the fop routines from the kernel or
* somehow hooking the fops calls. It may also be possible to
* leave the 66Mhz clock on and readjust the timing
* parameters.
*/
if (((ultra_66) || (ultra_100) || (ultra_133)) && (cable)) {
#ifdef DEBUG
printk("ULTRA66: %s channel of Ultra 66 requires an 80-pin cable for Ultra66 operation.\n", hwif->channel ? "Secondary" : "Primary");
printk(" Switching to Ultra33 mode.\n");
#endif /* DEBUG */
/* Primary : zero out second bit */
/* Secondary : zero out fourth bit */
if (!jumpbit)
OUT_BYTE(CLKSPD & ~mask, (high_16 + 0x11));
printk("Warning: %s channel requires an 80-pin cable for operation.\n", hwif->channel ? "Secondary":"Primary");
printk("%s reduced to Ultra33 mode.\n", drive->name);
udma_66 = 0; udma_100 = 0; udma_133 = 0;
} else {
if ((ultra_66) || (ultra_100) || (ultra_133)) {
/*
* check to make sure drive on same channel
* is u66 capable
*/
if (hwif->drives[!(drive->dn%2)].id) {
if ((hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0040) ||
(hwif->drives[!(drive->dn%2)].id->dma_ultra
& 0x0020) ||
(hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0010) ||
(hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0008)) {
if (!jumpbit)
OUT_BYTE(CLKSPD | mask, (high_16 + 0x11));
} else {
if (!jumpbit)
OUT_BYTE(CLKSPD & ~mask, (high_16 + 0x11));
}
} else { /* udma4 drive by itself */
if (!jumpbit)
OUT_BYTE(CLKSPD | mask, (high_16 + 0x11));
}
}
}
if (jumpbit) {
if (drive->media != ide_disk) return ide_dma_off_quietly;
if (id->capability & 4) { /* IORDY_EN & PREFETCH_EN */
OUT_BYTE((iordy + adj), indexreg);
OUT_BYTE((IN_BYTE(datareg)|0x03), datareg);
}
goto jumpbit_is_set;
}
switch(drive->dn) {
case 0: drive_pci = 0x60;
pci_read_config_dword(dev, drive_pci, &drive_conf);
if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
goto chipset_is_set;
pci_read_config_byte(dev, (drive_pci), &test1);
if (!(test1 & SYNC_ERRDY_EN))
pci_write_config_byte(dev, (drive_pci), test1|SYNC_ERRDY_EN);
break;
case 1: drive_pci = 0x64;
pci_read_config_dword(dev, drive_pci, &drive_conf);
if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
goto chipset_is_set;
pci_read_config_byte(dev, 0x60, &test1);
pci_read_config_byte(dev, (drive_pci), &test2);
if ((test1 & SYNC_ERRDY_EN) && !(test2 & SYNC_ERRDY_EN))
pci_write_config_byte(dev, (drive_pci), test2|SYNC_ERRDY_EN);
break;
case 2: drive_pci = 0x68;
pci_read_config_dword(dev, drive_pci, &drive_conf);
if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
goto chipset_is_set;
pci_read_config_byte(dev, (drive_pci), &test1);
if (!(test1 & SYNC_ERRDY_EN))
pci_write_config_byte(dev, (drive_pci), test1|SYNC_ERRDY_EN);
break;
case 3: drive_pci = 0x6c;
pci_read_config_dword(dev, drive_pci, &drive_conf);
if ((drive_conf != 0x004ff304) && (drive_conf != 0x004ff3c4))
goto chipset_is_set;
pci_read_config_byte(dev, 0x68, &test1);
pci_read_config_byte(dev, (drive_pci), &test2);
if ((test1 & SYNC_ERRDY_EN) && !(test2 & SYNC_ERRDY_EN))
pci_write_config_byte(dev, (drive_pci), test2|SYNC_ERRDY_EN);
break;
default:
return ide_dma_off;
}
chipset_is_set:
if (drive->media != ide_disk) return ide_dma_off_quietly;
pci_read_config_byte(dev, (drive_pci), &AP);
if (id->capability & 4) /* IORDY_EN */
pci_write_config_byte(dev, (drive_pci), AP|IORDY_EN);
pci_read_config_byte(dev, (drive_pci), &AP);
if (drive->media == ide_disk) /* PREFETCH_EN */
pci_write_config_byte(dev, (drive_pci), AP|PREFETCH_EN);
jumpbit_is_set:
if ((id->dma_ultra & 0x0040)&&(udma_133)) speed = XFER_UDMA_6;
else if ((id->dma_ultra & 0x0020)&&(udma_100)) speed = XFER_UDMA_5;
else if ((id->dma_ultra & 0x0010)&&(udma_66)) speed = XFER_UDMA_4;
else if ((id->dma_ultra & 0x0008)&&(udma_66)) speed = XFER_UDMA_3;
else if ((id->dma_ultra & 0x0004)&&(udma_33)) speed = XFER_UDMA_2;
else if ((id->dma_ultra & 0x0002)&&(udma_33)) speed = XFER_UDMA_1;
else if ((id->dma_ultra & 0x0001)&&(udma_33)) speed = XFER_UDMA_0;
else if (id->dma_mword & 0x0004) speed = XFER_MW_DMA_2;
else if (id->dma_mword & 0x0002) speed = XFER_MW_DMA_1;
else if (id->dma_mword & 0x0001) speed = XFER_MW_DMA_0;
else if ((id->dma_1word & 0x0004)&&(!jumpbit)) speed = XFER_SW_DMA_2;
else if ((id->dma_1word & 0x0002)&&(!jumpbit)) speed = XFER_SW_DMA_1;
else if ((id->dma_1word & 0x0001)&&(!jumpbit)) speed = XFER_SW_DMA_0;
else {
/* restore original pci-config space */
if (!jumpbit)
pci_write_config_dword(dev, drive_pci, drive_conf);
return ide_dma_off_quietly;
}
outb(inb(dma_base+2) & ~(1<<(5+unit)), dma_base+2);
(void) hwif->speedproc(drive, speed);
return ((int) ((id->dma_ultra >> 14) & 3) ? ide_dma_on :
((id->dma_ultra >> 11) & 7) ? ide_dma_on :
((id->dma_ultra >> 8) & 7) ? ide_dma_on :
((id->dma_mword >> 8) & 7) ? ide_dma_on :
((id->dma_1word >> 8) & 7) ? ide_dma_on :
ide_dma_off_quietly);
}
static int config_drive_xfer_rate (ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = HWIF(drive);
ide_dma_action_t dma_func = ide_dma_off_quietly;
if (id && (id->capability & 1) && hwif->autodma) {
/* Consult the list of known "bad" drives */
if (ide_dmaproc(ide_dma_bad_drive, drive)) {
dma_func = ide_dma_off;
goto fast_ata_pio;
}
dma_func = ide_dma_off_quietly;
if (id->field_valid & 4) {
if (id->dma_ultra & 0x007F) {
/* Force if Capable UltraDMA */
dma_func = config_chipset_for_dma(drive, 1);
if ((id->field_valid & 2) &&
(dma_func != ide_dma_on))
goto try_dma_modes;
}
} else if (id->field_valid & 2) {
try_dma_modes:
if ((id->dma_mword & 0x0007) ||
(id->dma_1word & 0x0007)) {
/* Force if Capable regular DMA modes */
dma_func = config_chipset_for_dma(drive, 0);
if (dma_func != ide_dma_on)
goto no_dma_set;
}
} else if (ide_dmaproc(ide_dma_good_drive, drive)) {
if (id->eide_dma_time > 150) {
goto no_dma_set;
}
/* Consult the list of known "good" drives */
dma_func = config_chipset_for_dma(drive, 0);
if (dma_func != ide_dma_on)
goto no_dma_set;
} else {
goto fast_ata_pio;
}
} else if ((id->capability & 8) || (id->field_valid & 2)) {
fast_ata_pio:
dma_func = ide_dma_off_quietly;
no_dma_set:
(void) config_chipset_for_pio(drive, 5);
}
return HWIF(drive)->dmaproc(dma_func, drive);
}
int pdc202xx_quirkproc (ide_drive_t *drive)
{
return ((int) check_in_drive_lists(drive, pdc_quirk_drives));
}
/*
* pdc202xx_dmaproc() initiates/aborts (U)DMA read/write operations on a drive.
*/
int pdc202xx_dmaproc (ide_dma_action_t func, ide_drive_t *drive)
{
byte dma_stat = 0;
byte sc1d = 0;
byte newchip = 0;
byte clock = 0;
byte hardware48hack = 0;
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
unsigned long high_16 = pci_resource_start(dev, 4);
unsigned long atapi_reg = high_16 + (hwif->channel ? 0x24 : 0x00);
unsigned long dma_base = hwif->dma_base;
switch (dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
case PCI_DEVICE_ID_PROMISE_20268R:
case PCI_DEVICE_ID_PROMISE_20268:
newchip = 1;
break;
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
case PCI_DEVICE_ID_PROMISE_20262:
hardware48hack = 1;
clock = IN_BYTE(high_16 + 0x11);
default:
break;
}
switch (func) {
case ide_dma_check:
return config_drive_xfer_rate(drive);
case ide_dma_begin:
/* Note that this is done *after* the cmd has
* been issued to the drive, as per the BM-IDE spec.
* The Promise Ultra33 doesn't work correctly when
* we do this part before issuing the drive cmd.
*/
if ((drive->addressing) && (hardware48hack)) {
struct request *rq = HWGROUP(drive)->rq;
unsigned long word_count = 0;
outb(clock|(hwif->channel ? 0x08 : 0x02), high_16 + 0x11);
word_count = (rq->nr_sectors << 8);
word_count = (rq->cmd == READ) ? word_count | 0x05000000 : word_count | 0x06000000;
outl(word_count, atapi_reg);
}
break;
case ide_dma_end:
if ((drive->addressing) && (hardware48hack)) {
outl(0, atapi_reg); /* zero out extra */
clock = IN_BYTE(high_16 + 0x11);
OUT_BYTE(clock & ~(hwif->channel ? 0x08:0x02), high_16 + 0x11);
}
break;
case ide_dma_test_irq: /* returns 1 if dma irq issued, 0 otherwise */
dma_stat = IN_BYTE(dma_base+2);
if (newchip)
return (dma_stat & 4) == 4;
sc1d = IN_BYTE(high_16 + 0x001d);
if (HWIF(drive)->channel) {
if ((sc1d & 0x50) == 0x50) goto somebody_else;
else if ((sc1d & 0x40) == 0x40)
return (dma_stat & 4) == 4;
} else {
if ((sc1d & 0x05) == 0x05) goto somebody_else;
else if ((sc1d & 0x04) == 0x04)
return (dma_stat & 4) == 4;
}
somebody_else:
return (dma_stat & 4) == 4; /* return 1 if INTR asserted */
case ide_dma_lostirq:
case ide_dma_timeout:
if (HWIF(drive)->resetproc != NULL)
HWIF(drive)->resetproc(drive);
default:
break;
}
return ide_dmaproc(func, drive); /* use standard DMA stuff */
}
#endif /* CONFIG_BLK_DEV_IDEDMA */
void pdc202xx_new_reset (ide_drive_t *drive)
{
OUT_BYTE(0x04,IDE_CONTROL_REG);
mdelay(1000);
OUT_BYTE(0x00,IDE_CONTROL_REG);
mdelay(1000);
printk("PDC202XX: %s channel reset.\n",
HWIF(drive)->channel ? "Secondary" : "Primary");
}
void pdc202xx_reset (ide_drive_t *drive)
{
unsigned long high_16 = pci_resource_start(HWIF(drive)->pci_dev, 4);
byte udma_speed_flag = IN_BYTE(high_16 + 0x001f);
OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
mdelay(100);
OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
mdelay(2000); /* 2 seconds ?! */
printk("PDC202XX: %s channel reset.\n",
HWIF(drive)->channel ? "Secondary" : "Primary");
}
/*
* Since SUN Cobalt is attempting to do this operation, I should disclose
* this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
* HOTSWAP ATA Infrastructure.
*/
static int pdc202xx_tristate (ide_drive_t * drive, int state)
{
#if 0
ide_hwif_t *hwif = HWIF(drive);
unsigned long high_16 = pci_resource_start(hwif->pci_dev, 4);
byte sc1f = inb(high_16 + 0x001f);
if (!hwif)
return -EINVAL;
// hwif->bus_state = state;
if (state) {
outb(sc1f | 0x08, high_16 + 0x001f);
} else {
outb(sc1f & ~0x08, high_16 + 0x001f);
}
#endif
return 0;
}
unsigned int __init pci_init_pdc202xx (struct pci_dev *dev, const char *name)
{
unsigned long high_16 = pci_resource_start(dev, 4);
byte udma_speed_flag = IN_BYTE(high_16 + 0x001f);
byte primary_mode = IN_BYTE(high_16 + 0x001a);
byte secondary_mode = IN_BYTE(high_16 + 0x001b);
byte newchip = 0;
if (dev->resource[PCI_ROM_RESOURCE].start) {
pci_write_config_dword(dev, PCI_ROM_ADDRESS, dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
printk("%s: ROM enabled at 0x%08lx\n", name, dev->resource[PCI_ROM_RESOURCE].start);
}
switch (dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
case PCI_DEVICE_ID_PROMISE_20268R:
case PCI_DEVICE_ID_PROMISE_20268:
newchip = 1;
break;
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
mdelay(100);
OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
mdelay(2000); /* 2 seconds ?! */
break;
case PCI_DEVICE_ID_PROMISE_20262:
/*
* software reset - this is required because the bios
* will set UDMA timing on if the hdd supports it. The
* user may want to turn udma off. A bug in the pdc20262
* is that it cannot handle a downgrade in timing from
* UDMA to DMA. Disk accesses after issuing a set
* feature command will result in errors. A software
* reset leaves the timing registers intact,
* but resets the drives.
*/
OUT_BYTE(udma_speed_flag | 0x10, high_16 + 0x001f);
mdelay(100);
OUT_BYTE(udma_speed_flag & ~0x10, high_16 + 0x001f);
mdelay(2000); /* 2 seconds ?! */
default:
if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE) {
byte irq = 0, irq2 = 0;
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq);
pci_read_config_byte(dev, (PCI_INTERRUPT_LINE)|0x80, &irq2); /* 0xbc */
if (irq != irq2) {
pci_write_config_byte(dev, (PCI_INTERRUPT_LINE)|0x80, irq); /* 0xbc */
printk("%s: pci-config space interrupt mirror fixed.\n", name);
}
}
break;
}
if (newchip)
goto fttk_tx_series;
printk("%s: (U)DMA Burst Bit %sABLED " \
"Primary %s Mode " \
"Secondary %s Mode.\n",
name,
(udma_speed_flag & 1) ? "EN" : "DIS",
(primary_mode & 1) ? "MASTER" : "PCI",
(secondary_mode & 1) ? "MASTER" : "PCI" );
#ifdef CONFIG_PDC202XX_BURST
if (!(udma_speed_flag & 1)) {
printk("%s: FORCING BURST BIT 0x%02x -> 0x%02x ", name, udma_speed_flag, (udma_speed_flag|1));
OUT_BYTE(udma_speed_flag|1, high_16 + 0x001f);
printk("%sCTIVE\n", (IN_BYTE(high_16 + 0x001f) & 1) ? "A" : "INA");
}
#endif /* CONFIG_PDC202XX_BURST */
#ifdef CONFIG_PDC202XX_MASTER
if (!(primary_mode & 1)) {
printk("%s: FORCING PRIMARY MODE BIT 0x%02x -> 0x%02x ",
name, primary_mode, (primary_mode|1));
OUT_BYTE(primary_mode|1, high_16 + 0x001a);
printk("%s\n", (IN_BYTE(high_16 + 0x001a) & 1) ? "MASTER" : "PCI");
}
if (!(secondary_mode & 1)) {
printk("%s: FORCING SECONDARY MODE BIT 0x%02x -> 0x%02x ",
name, secondary_mode, (secondary_mode|1));
OUT_BYTE(secondary_mode|1, high_16 + 0x001b);
printk("%s\n", (IN_BYTE(high_16 + 0x001b) & 1) ? "MASTER" : "PCI");
}
#endif /* CONFIG_PDC202XX_MASTER */
fttk_tx_series:
#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS)
if (!pdc202xx_proc) {
pdc202xx_proc = 1;
bmide_dev = dev;
pdc202xx_display_info = &pdc202xx_get_info;
}
#endif /* DISPLAY_PDC202XX_TIMINGS && CONFIG_PROC_FS */
return dev->irq;
}
unsigned int __init ata66_pdc202xx (ide_hwif_t *hwif)
{
unsigned short mask = (hwif->channel) ? (1<<11) : (1<<10);
unsigned short CIS;
switch(hwif->pci_dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
case PCI_DEVICE_ID_PROMISE_20268:
case PCI_DEVICE_ID_PROMISE_20268R:
OUT_BYTE(0x0b, (hwif->dma_base + 1));
return (!(IN_BYTE((hwif->dma_base + 3)) & 0x04));
default:
pci_read_config_word(hwif->pci_dev, 0x50, &CIS);
return (!(CIS & mask));
}
}
void __init ide_init_pdc202xx (ide_hwif_t *hwif)
{
hwif->tuneproc = &pdc202xx_tune_drive;
hwif->quirkproc = &pdc202xx_quirkproc;
switch(hwif->pci_dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
case PCI_DEVICE_ID_PROMISE_20275:
case PCI_DEVICE_ID_PROMISE_20269:
case PCI_DEVICE_ID_PROMISE_20268:
case PCI_DEVICE_ID_PROMISE_20268R:
hwif->speedproc = &pdc202xx_new_tune_chipset;
hwif->resetproc = &pdc202xx_new_reset;
break;
case PCI_DEVICE_ID_PROMISE_20267:
case PCI_DEVICE_ID_PROMISE_20265:
case PCI_DEVICE_ID_PROMISE_20262:
hwif->busproc = &pdc202xx_tristate;
hwif->resetproc = &pdc202xx_reset;
case PCI_DEVICE_ID_PROMISE_20246:
hwif->speedproc = &pdc202xx_tune_chipset;
default:
break;
}
#undef CONFIG_PDC202XX_32_UNMASK
#ifdef CONFIG_PDC202XX_32_UNMASK
hwif->drives[0].io_32bit = 1;
hwif->drives[1].io_32bit = 1;
hwif->drives[0].unmask = 1;
hwif->drives[1].unmask = 1;
#endif /* CONFIG_PDC202XX_32_UNMASK */
#ifdef CONFIG_BLK_DEV_IDEDMA
if (hwif->dma_base) {
hwif->dmaproc = &pdc202xx_dmaproc;
if (!noautodma)
hwif->autodma = 1;
} else {
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->autodma = 0;
}
#else /* !CONFIG_BLK_DEV_IDEDMA */
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
hwif->autodma = 0;
#endif /* CONFIG_BLK_DEV_IDEDMA */
}
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2002-03-28 17:24 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-03-28 17:27 Patch for ide/pdc202xx.c Markus Sinner
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox