* [PATCH v2 0/2] Add bootph-all property to necessary nodes to enable ethernet boot for AM68-SK, J722s and AM62p-SK
@ 2025-03-02 15:35 Chintan Vankar
2025-03-02 15:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot Chintan Vankar
2025-03-02 15:35 ` [PATCH v2 2/2] arm64: dts: ti: k3-am62p5*/k3-j722s: " Chintan Vankar
0 siblings, 2 replies; 6+ messages in thread
From: Chintan Vankar @ 2025-03-02 15:35 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Tero Kristo,
Vignesh Raghavendra, Nishanth Menon
Cc: s-vadapalli, c-vankar, linux-kernel, devicetree, linux-arm-kernel
This series adds bootph-all property to necessary nodes to enable
ethernet boot support for AM68-SK, J722s and AM62p-SK.
This series is based on linux-next tagged next-20250228.
Link to v1:
https://lore.kernel.org/r/20250106123122.3531845-1-c-vankar@ti.com/
Changes from v1 to v2:
- Updated order of "bootph-all" in [PATCH 1/1].
Chintan Vankar (2):
arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to
enable Ethernet boot
arm64: dts: ti: k3-am62p5*/k3-j722s: Add bootph-all property to enable
Ethernet boot
arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi | 3 +++
arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 2 ++
arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 3 +++
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 ++++
arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 3 +++
5 files changed, 15 insertions(+)
--
2.34.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot
2025-03-02 15:35 [PATCH v2 0/2] Add bootph-all property to necessary nodes to enable ethernet boot for AM68-SK, J722s and AM62p-SK Chintan Vankar
@ 2025-03-02 15:35 ` Chintan Vankar
2025-03-03 5:44 ` Siddharth Vadapalli
2025-03-03 8:14 ` Vignesh Raghavendra
2025-03-02 15:35 ` [PATCH v2 2/2] arm64: dts: ti: k3-am62p5*/k3-j722s: " Chintan Vankar
1 sibling, 2 replies; 6+ messages in thread
From: Chintan Vankar @ 2025-03-02 15:35 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Tero Kristo,
Vignesh Raghavendra, Nishanth Menon
Cc: s-vadapalli, c-vankar, linux-kernel, devicetree, linux-arm-kernel
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
on AM68-SK and J721S2-EVM.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
Link to v1:
https://lore.kernel.org/r/20250106123122.3531845-2-c-vankar@ti.com/
Changes from v1 to v2:
- No changes.
arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 3 +++
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 ++++
2 files changed, 7 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 11522b36e0ce..8e9101dd2152 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -333,6 +333,7 @@ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>;
+ bootph-all;
};
mcu_mdio_pins_default: mcu-mdio-default-pins {
@@ -340,6 +341,7 @@ mcu_mdio_pins_default: mcu-mdio-default-pins {
J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>;
+ bootph-all;
};
mcu_mcan0_pins_default: mcu-mcan0-default-pins {
@@ -615,6 +617,7 @@ &mcu_cpsw {
&davinci_mdio {
phy0: ethernet-phy@0 {
reg = <0>;
+ bootph-all;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
ti,min-output-impedance;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index bc31266126d0..29cd4b1ffbbf 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -154,12 +154,14 @@ mcu_conf: bus@40f00000 {
cpsw_mac_syscon: ethernet-mac-syscon@200 {
compatible = "ti,am62p-cpsw-mac-efuse", "syscon";
reg = <0x200 0x8>;
+ bootph-all;
};
phy_gmii_sel: phy@4040 {
compatible = "ti,am654-phy-gmii-sel";
reg = <0x4040 0x4>;
#phy-cells = <1>;
+ bootph-all;
};
};
@@ -538,6 +540,7 @@ mcu_cpsw: ethernet@46000000 {
clocks = <&k3_clks 29 28>;
clock-names = "fck";
power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>;
+ bootph-all;
dmas = <&mcu_udmap 0xf000>,
<&mcu_udmap 0xf001>,
@@ -562,6 +565,7 @@ cpsw_port1: port@1 {
label = "port1";
ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
phys = <&phy_gmii_sel 1>;
+ bootph-all;
};
};
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 2/2] arm64: dts: ti: k3-am62p5*/k3-j722s: Add bootph-all property to enable Ethernet boot
2025-03-02 15:35 [PATCH v2 0/2] Add bootph-all property to necessary nodes to enable ethernet boot for AM68-SK, J722s and AM62p-SK Chintan Vankar
2025-03-02 15:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot Chintan Vankar
@ 2025-03-02 15:35 ` Chintan Vankar
1 sibling, 0 replies; 6+ messages in thread
From: Chintan Vankar @ 2025-03-02 15:35 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Tero Kristo,
Vignesh Raghavendra, Nishanth Menon
Cc: s-vadapalli, c-vankar, linux-kernel, devicetree, linux-arm-kernel,
Roger Quadros
Ethernet boot requires CPSW nodes to be present starting from R5 SPL
stage. Add bootph-all property to required nodes to enable Ethernet boot
for AM62p-SK and J722s.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
Link to v1:
https://lore.kernel.org/r/20250106123122.3531845-3-c-vankar@ti.com/
Changes from v1 to v2:
- Updated order of "bootph-all" property for cpsw_port1 node in
"k3-am62p-j722s-common-main.dtsi".
arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi | 3 +++
arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 2 ++
arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 3 +++
3 files changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi
index 6e3beb5c2e01..b88b8fa5f28a 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi
@@ -50,6 +50,7 @@ phy_gmii_sel: phy@4044 {
compatible = "ti,am654-phy-gmii-sel";
reg = <0x4044 0x8>;
#phy-cells = <1>;
+ bootph-all;
};
epwm_tbclk: clock-controller@4130 {
@@ -721,6 +722,7 @@ cpsw_port1: port@1 {
mac-address = [00 00 00 00 00 00];
ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
status = "disabled";
+ bootph-all;
};
cpsw_port2: port@2 {
@@ -742,6 +744,7 @@ cpsw3g_mdio: mdio@f00 {
clock-names = "fck";
bus_freq = <1000000>;
status = "disabled";
+ bootph-all;
};
cpts@3d000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
index ad71d2f27f53..28b08eb79da3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
@@ -226,6 +226,7 @@ main_mdio1_pins_default: main-mdio1-default-pins {
AM62PX_IOPAD(0x0160, PIN_OUTPUT, 0) /* (F17) MDIO0_MDC */
AM62PX_IOPAD(0x015c, PIN_INPUT, 0) /* (F16) MDIO0_MDIO */
>;
+ bootph-all;
};
main_mmc1_pins_default: main-mmc1-default-pins {
@@ -495,6 +496,7 @@ &cpsw3g_mdio {
cpsw3g_phy0: ethernet-phy@0 {
reg = <0>;
+ bootph-all;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
ti,min-output-impedance;
diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
index d184e9c1a0a5..054425afd764 100644
--- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
@@ -303,6 +303,7 @@ mdio_pins_default: mdio-default-pins {
J722S_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AC24) MDIO0_MDC */
J722S_IOPAD(0x015c, PIN_INPUT, 0) /* (AD25) MDIO0_MDIO */
>;
+ bootph-all;
};
ospi0_pins_default: ospi0-default-pins {
@@ -337,6 +338,7 @@ J722S_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AF24) RGMII1_TD3 */
J722S_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AG26) RGMII1_TXC */
J722S_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AF25) RGMII1_TX_CTL */
>;
+ bootph-all;
};
main_usb1_pins_default: main-usb1-default-pins {
@@ -381,6 +383,7 @@ &cpsw3g_mdio {
cpsw3g_phy0: ethernet-phy@0 {
reg = <0>;
+ bootph-all;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
ti,min-output-impedance;
--
2.34.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot
2025-03-02 15:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot Chintan Vankar
@ 2025-03-03 5:44 ` Siddharth Vadapalli
2025-03-03 8:14 ` Vignesh Raghavendra
1 sibling, 0 replies; 6+ messages in thread
From: Siddharth Vadapalli @ 2025-03-03 5:44 UTC (permalink / raw)
To: Chintan Vankar
Cc: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Tero Kristo,
Vignesh Raghavendra, Nishanth Menon, s-vadapalli, linux-kernel,
devicetree, linux-arm-kernel
On Sun, Mar 02, 2025 at 09:05:01PM +0530, Chintan Vankar wrote:
> Ethernet boot requires CPSW nodes to be present starting from R5 SPL
> stage. Add bootph-all property to required nodes to enable Ethernet boot
> on AM68-SK and J721S2-EVM.
>
> Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Regards,
Siddharth.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot
2025-03-02 15:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot Chintan Vankar
2025-03-03 5:44 ` Siddharth Vadapalli
@ 2025-03-03 8:14 ` Vignesh Raghavendra
2025-03-03 18:26 ` Vankar, Chintan
1 sibling, 1 reply; 6+ messages in thread
From: Vignesh Raghavendra @ 2025-03-03 8:14 UTC (permalink / raw)
To: Chintan Vankar, Conor Dooley, Krzysztof Kozlowski, Rob Herring,
Tero Kristo, Nishanth Menon
Cc: s-vadapalli, linux-kernel, devicetree, linux-arm-kernel
On 02/03/25 21:05, Chintan Vankar wrote:
> Ethernet boot requires CPSW nodes to be present starting from R5 SPL
> stage. Add bootph-all property to required nodes to enable Ethernet boot
> on AM68-SK and J721S2-EVM.
>
> Signed-off-by: Chintan Vankar <c-vankar@ti.com>
> ---
>
> Link to v1:
> https://lore.kernel.org/r/20250106123122.3531845-2-c-vankar@ti.com/
>
> Changes from v1 to v2:
> - No changes.
>
> arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 3 +++
> arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 ++++
> 2 files changed, 7 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> index 11522b36e0ce..8e9101dd2152 100644
> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> @@ -333,6 +333,7 @@ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
> J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
> J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
> >;
> + bootph-all;
> };
>
> mcu_mdio_pins_default: mcu-mdio-default-pins {
> @@ -340,6 +341,7 @@ mcu_mdio_pins_default: mcu-mdio-default-pins {
> J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
> J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
> >;
> + bootph-all;
> };
>
> mcu_mcan0_pins_default: mcu-mcan0-default-pins {
> @@ -615,6 +617,7 @@ &mcu_cpsw {
> &davinci_mdio {
> phy0: ethernet-phy@0 {
> reg = <0>;
> + bootph-all;
> ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> ti,min-output-impedance;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> index bc31266126d0..29cd4b1ffbbf 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
> @@ -154,12 +154,14 @@ mcu_conf: bus@40f00000 {
> cpsw_mac_syscon: ethernet-mac-syscon@200 {
> compatible = "ti,am62p-cpsw-mac-efuse", "syscon";
> reg = <0x200 0x8>;
> + bootph-all;
> };
>
> phy_gmii_sel: phy@4040 {
> compatible = "ti,am654-phy-gmii-sel";
> reg = <0x4040 0x4>;
> #phy-cells = <1>;
> + bootph-all;
> };
>
> };
> @@ -538,6 +540,7 @@ mcu_cpsw: ethernet@46000000 {
> clocks = <&k3_clks 29 28>;
> clock-names = "fck";
> power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>;
> + bootph-all;
>
Since a child node has bootph-all, no need to put the same in the parent
hierarchy.
> dmas = <&mcu_udmap 0xf000>,
> <&mcu_udmap 0xf001>,
> @@ -562,6 +565,7 @@ cpsw_port1: port@1 {
> label = "port1";
> ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
> phys = <&phy_gmii_sel 1>;
> + bootph-all;
> };
> };
>
--
Regards
Vignesh
https://ti.com/opensource
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot
2025-03-03 8:14 ` Vignesh Raghavendra
@ 2025-03-03 18:26 ` Vankar, Chintan
0 siblings, 0 replies; 6+ messages in thread
From: Vankar, Chintan @ 2025-03-03 18:26 UTC (permalink / raw)
To: Vignesh Raghavendra, Conor Dooley, Krzysztof Kozlowski,
Rob Herring, Tero Kristo, Nishanth Menon
Cc: s-vadapalli, linux-kernel, devicetree, linux-arm-kernel
Hello Vignesh,
On 3/3/2025 1:44 PM, Vignesh Raghavendra wrote:
>
>
> On 02/03/25 21:05, Chintan Vankar wrote:
>> Ethernet boot requires CPSW nodes to be present starting from R5 SPL
>> stage. Add bootph-all property to required nodes to enable Ethernet boot
>> on AM68-SK and J721S2-EVM.
>>
>> Signed-off-by: Chintan Vankar <c-vankar@ti.com>
>> ---
>>
>> Link to v1:
>> https://lore.kernel.org/r/20250106123122.3531845-2-c-vankar@ti.com/
>>
>> Changes from v1 to v2:
>> - No changes.
>>
>> arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 3 +++
>> arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 ++++
>> 2 files changed, 7 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
>> index 11522b36e0ce..8e9101dd2152 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
>> @@ -333,6 +333,7 @@ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
>> J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
>> J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>> >;
>> + bootph-all;
>> };
>>
>> mcu_mdio_pins_default: mcu-mdio-default-pins {
>> @@ -340,6 +341,7 @@ mcu_mdio_pins_default: mcu-mdio-default-pins {
>> J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
>> J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>> >;
>> + bootph-all;
>> };
>>
>> mcu_mcan0_pins_default: mcu-mcan0-default-pins {
>> @@ -615,6 +617,7 @@ &mcu_cpsw {
>> &davinci_mdio {
>> phy0: ethernet-phy@0 {
>> reg = <0>;
>> + bootph-all;
>> ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
>> ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
>> ti,min-output-impedance;
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
>> index bc31266126d0..29cd4b1ffbbf 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
>> @@ -154,12 +154,14 @@ mcu_conf: bus@40f00000 {
>> cpsw_mac_syscon: ethernet-mac-syscon@200 {
>> compatible = "ti,am62p-cpsw-mac-efuse", "syscon";
>> reg = <0x200 0x8>;
>> + bootph-all;
>> };
>>
>> phy_gmii_sel: phy@4040 {
>> compatible = "ti,am654-phy-gmii-sel";
>> reg = <0x4040 0x4>;
>> #phy-cells = <1>;
>> + bootph-all;
>> };
>>
>> };
>> @@ -538,6 +540,7 @@ mcu_cpsw: ethernet@46000000 {
>> clocks = <&k3_clks 29 28>;
>> clock-names = "fck";
>> power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>;
>> + bootph-all;
>>
>
> Since a child node has bootph-all, no need to put the same in the parent
> hierarchy.
>
Thank you for pointing this out, I will remove it from the parent node
and post the next version.
Regards,
Chintan.
>> dmas = <&mcu_udmap 0xf000>,
>> <&mcu_udmap 0xf001>,
>> @@ -562,6 +565,7 @@ cpsw_port1: port@1 {
>> label = "port1";
>> ti,syscon-efuse = <&cpsw_mac_syscon 0x0>;
>> phys = <&phy_gmii_sel 1>;
>> + bootph-all;
>> };
>> };
>>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2025-03-03 18:26 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-03-02 15:35 [PATCH v2 0/2] Add bootph-all property to necessary nodes to enable ethernet boot for AM68-SK, J722s and AM62p-SK Chintan Vankar
2025-03-02 15:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am68-sk/k3-j721s2-mcu: Add bootph-all property to enable Ethernet boot Chintan Vankar
2025-03-03 5:44 ` Siddharth Vadapalli
2025-03-03 8:14 ` Vignesh Raghavendra
2025-03-03 18:26 ` Vankar, Chintan
2025-03-02 15:35 ` [PATCH v2 2/2] arm64: dts: ti: k3-am62p5*/k3-j722s: " Chintan Vankar
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox