Re: [PATCH net-next v3 9/9] net: phy: icplus: add MDI/MDIX support for IP101A/G

[Michael Walle <michael@walle.cc>]

Am 2021-02-10 22:08, schrieb Michael Walle:
> Implement the operations to set desired mode and retrieve the current
> mode.
> 
> This feature was tested with an IP101G.
> 
> Signed-off-by: Michael Walle <michael@walle.cc>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> ---
> Changes since v2:
>  - none
> 
> Changes since v1:
>  - none, except that the callbacks are register for both IP101A and 
> IP101G
>    PHY drivers
> 
>  drivers/net/phy/icplus.c | 93 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 93 insertions(+)
> 
> diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c
> index 96e9d1d12992..cc5b25714002 100644
> --- a/drivers/net/phy/icplus.c
> +++ b/drivers/net/phy/icplus.c
> @@ -37,12 +37,17 @@ MODULE_LICENSE("GPL");
>  #define IP1001_SPEC_CTRL_STATUS_2	20	/* IP1001 Spec. Control Reg 2 */
>  #define IP1001_APS_ON			11	/* IP1001 APS Mode  bit */
>  #define IP101A_G_APS_ON			BIT(1)	/* IP101A/G APS Mode bit */
> +#define IP101A_G_AUTO_MDIX_DIS		BIT(11)
>  #define IP101A_G_IRQ_CONF_STATUS	0x11	/* Conf Info IRQ & Status Reg */
>  #define	IP101A_G_IRQ_PIN_USED		BIT(15) /* INTR pin used */
>  #define IP101A_G_IRQ_ALL_MASK		BIT(11) /* IRQ's inactive */
>  #define IP101A_G_IRQ_SPEED_CHANGE	BIT(2)
>  #define IP101A_G_IRQ_DUPLEX_CHANGE	BIT(1)
>  #define IP101A_G_IRQ_LINK_CHANGE	BIT(0)
> +#define IP101A_G_PHY_STATUS		18
> +#define IP101A_G_MDIX			BIT(9)
> +#define IP101A_G_PHY_SPEC_CTRL		30
> +#define IP101A_G_FORCE_MDIX		BIT(3)
> 
>  #define IP101G_PAGE_CONTROL				0x14
>  #define IP101G_PAGE_CONTROL_MASK			GENMASK(4, 0)
> @@ -297,6 +302,90 @@ static int ip101g_config_init(struct phy_device 
> *phydev)
>  	return ip101a_g_config_intr_pin(phydev);
>  }
> 
> +static int ip101a_g_read_status(struct phy_device *phydev)
> +{
> +	int oldpage, ret, stat1, stat2;
> +
> +	ret = genphy_read_status(phydev);
> +	if (ret)
> +		return ret;
> +
> +	oldpage = phy_select_page(phydev, IP101G_DEFAULT_PAGE);

same here, missing return code check, will be fixed in v4

> +
> +	ret = __phy_read(phydev, IP10XX_SPEC_CTRL_STATUS);
> +	if (ret < 0)
> +		goto out;
> +	stat1 = ret;
> +
> +	ret = __phy_read(phydev, IP101A_G_PHY_SPEC_CTRL);
> +	if (ret < 0)
> +		goto out;
> +	stat2 = ret;
> +
> +	if (stat1 & IP101A_G_AUTO_MDIX_DIS) {
> +		if (stat2 & IP101A_G_FORCE_MDIX)
> +			phydev->mdix_ctrl = ETH_TP_MDI_X;
> +		else
> +			phydev->mdix_ctrl = ETH_TP_MDI;
> +	} else {
> +		phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
> +	}
> +
> +	if (stat2 & IP101A_G_MDIX)
> +		phydev->mdix = ETH_TP_MDI_X;
> +	else
> +		phydev->mdix = ETH_TP_MDI;
> +
> +	ret = 0;
> +
> +out:
> +	return phy_restore_page(phydev, oldpage, ret);
> +}
> +
> +static int ip101a_g_config_mdix(struct phy_device *phydev)
> +{
> +	u16 ctrl = 0, ctrl2 = 0;
> +	int oldpage, ret;
> +
> +	switch (phydev->mdix_ctrl) {
> +	case ETH_TP_MDI:
> +		ctrl = IP101A_G_AUTO_MDIX_DIS;
> +		break;
> +	case ETH_TP_MDI_X:
> +		ctrl = IP101A_G_AUTO_MDIX_DIS;
> +		ctrl2 = IP101A_G_FORCE_MDIX;
> +		break;
> +	case ETH_TP_MDI_AUTO:
> +		break;
> +	default:
> +		return 0;
> +	}
> +
> +	oldpage = phy_select_page(phydev, IP101G_DEFAULT_PAGE);

dito

-michael

> +
> +	ret = __phy_modify(phydev, IP10XX_SPEC_CTRL_STATUS,
> +			   IP101A_G_AUTO_MDIX_DIS, ctrl);
> +	if (ret)
> +		goto out;
> +
> +	ret = __phy_modify(phydev, IP101A_G_PHY_SPEC_CTRL,
> +			   IP101A_G_FORCE_MDIX, ctrl2);
> +
> +out:
> +	return phy_restore_page(phydev, oldpage, ret);
> +}
> +
> +static int ip101a_g_config_aneg(struct phy_device *phydev)
> +{
> +	int ret;
> +
> +	ret = ip101a_g_config_mdix(phydev);
> +	if (ret)
> +		return ret;
> +
> +	return genphy_config_aneg(phydev);
> +}
> +
>  static int ip101a_g_ack_interrupt(struct phy_device *phydev)
>  {
>  	int err;
> @@ -502,6 +591,8 @@ static struct phy_driver icplus_driver[] = {
>  	.config_intr	= ip101a_g_config_intr,
>  	.handle_interrupt = ip101a_g_handle_interrupt,
>  	.config_init	= ip101a_config_init,
> +	.config_aneg	= ip101a_g_config_aneg,
> +	.read_status	= ip101a_g_read_status,
>  	.soft_reset	= genphy_soft_reset,
>  	.suspend	= genphy_suspend,
>  	.resume		= genphy_resume,
> @@ -514,6 +605,8 @@ static struct phy_driver icplus_driver[] = {
>  	.config_intr	= ip101a_g_config_intr,
>  	.handle_interrupt = ip101a_g_handle_interrupt,
>  	.config_init	= ip101g_config_init,
> +	.config_aneg	= ip101a_g_config_aneg,
> +	.read_status	= ip101a_g_read_status,
>  	.soft_reset	= genphy_soft_reset,
>  	.get_sset_count = ip101g_get_sset_count,
>  	.get_strings	= ip101g_get_strings,