* Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
@ 2009-08-02 16:40 Alex Riesen
2009-08-02 17:19 ` Oliver Neukum
0 siblings, 1 reply; 11+ messages in thread
From: Alex Riesen @ 2009-08-02 16:40 UTC (permalink / raw)
To: linux-usb
Cc: Oliver Neukum, Linux Kernel Mailing List, Greg Kroah-Hartman,
Alan Cox
[-- Attachment #1: Type: text/plain, Size: 6817 bytes --]
Starting since about 2.6.31-rc2, kernel oopses when I boot a kernel from
Openmoko's bootloader. The bootloader is connected through CDC ACM,
and when the kernel boots, the usb device changes to usb ethernet.
Shortly after that kernel oopses:
[ 29.346931] usb 5-1: USB disconnect, address 2
[ 29.347343] usb0: unregister 'cdc_ether' usb-0000:00:1d.0-1, CDC
Ethernet Device
[ 30.573530] usb 5-1: new full speed USB device using uhci_hcd and address 4
[ 30.750689] usb 5-1: New USB device found, idVendor=1457, idProduct=5119
[ 30.750795] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 30.750923] usb 5-1: Product: Neo1973 Bootloader U-Boot 1.3.2-rc2
[ 30.751005] usb 5-1: Manufacturer: OpenMoko, Inc
[ 30.751071] usb 5-1: SerialNumber: 0000000
[ 30.752032] usb 5-1: configuration #1 chosen from 2 choices
[ 30.793924] cdc_acm 5-1:1.0: This device cannot do calls on its
own. It is not a modem.
[ 30.794103] cdc_acm 5-1:1.0: ttyACM0: USB ACM device
[ 30.799509] usbcore: registered new interface driver cdc_acm
[ 30.799610] cdc_acm: v0.26:USB Abstract Control Model driver for
USB modems and ISDN adapters
[ 47.346852] usb 5-1: USB disconnect, address 4
[ 47.352989] tty_port_close_start: count = -1
[ 48.358107] tty_port_close_start: count = -1
[ 49.362088] tty_port_close_start: count = -1
[ 50.365975] tty_port_close_start: count = -1
[ 51.369831] tty_port_close_start: count = -1
[ 52.373640] tty_port_close_start: count = -1
[ 53.377348] tty_port_close_start: count = -1
[ 54.381038] tty_port_close_start: count = -1
[ 55.384717] tty_port_close_start: count = -1
[ 56.388336] tty_port_close_start: count = -1
[ 57.391932] tty_port_close_start: count = -1
[ 58.395485] tty_port_close_start: count = -1
[ 59.399000] tty_port_close_start: count = -1
[ 60.400401] tty_port_close_start: count = -1
[ 61.401795] tty_port_close_start: count = -1
[ 62.405239] tty_port_close_start: count = -1
[ 63.408676] tty_port_close_start: count = -1
[ 64.412031] tty_port_close_start: count = -1
[ 65.415241] tty_port_close_start: count = -1
[ 66.418339] tty_port_close_start: count = -1
[ 67.421433] tty_port_close_start: count = -1
[ 68.424520] tty_port_close_start: count = -1
[ 69.427630] tty_port_close_start: count = -1
[ 70.430787] tty_port_close_start: count = -1
[ 71.433903] tty_port_close_start: count = -1
[ 72.437040] tty_port_close_start: count = -1
[ 73.440171] tty_port_close_start: count = -1
[ 74.441520] tty_port_close_start: count = -1
[ 75.073519] usb 5-1: new full speed USB device using uhci_hcd and address 5
[ 75.271699] usb 5-1: New USB device found, idVendor=1457, idProduct=5122
[ 75.271709] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 75.271716] usb 5-1: Product: RNDIS/Ethernet Gadget
[ 75.271722] usb 5-1: Manufacturer: Linux 2.6.24/s3c2410_udc
[ 75.272788] usb 5-1: configuration #1 chosen from 2 choices
[ 75.288865] usb0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC
Ethernet Device, 1a:e0:cd:b1:57:c0
[ 75.442858] tty_port_close_start: count = -1
[ 75.442881] general protection fault: 0000 [#1] SMP
[ 75.444775] last sysfs file:
/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1/uevent
[ 75.446041] CPU 0
[ 75.446041] Modules linked in: cdc_acm uvcvideo cdc_ether usbnet
ohci1394 wmi videodev v4l1_compat v4l2_compat_ioctl32 ieee1394 mii
[ 75.446041] Pid: 2127, comm: minicom Not tainted 2.6.31-rc2-t #64
XPS M1330
[ 75.446041] RIP: 0010:[<ffffffff812a76e1>] [<ffffffff812a76e1>]
usb_autopm_do_interface+0x35/0xeb
[ 75.453444] RSP: 0018:ffff88007d05faf8 EFLAGS: 00010292
[ 75.453444] RAX: 656369766564646a RBX: 00000000ffffffed RCX: 0000000000000000
[ 75.453444] RDX: ffffffffa00755b8 RSI: 0000000000000001 RDI: 656369766564646a
[ 75.453444] RBP: ffff88007d05fb28 R08: 0000000000000001 R09: 0000000000000000
[ 75.453444] R10: ffffffff810594a7 R11: 0000000000000082 R12: ffff88007c527800
[ 75.453444] R13: 6563697665645ed2 R14: 6563697665645f62 R15: 0000000000000001
[ 75.453444] FS: 00007fe65d7916f0(0000) GS:ffff880001e56000(0000)
knlGS:0000000000000000
[ 75.453444] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 75.453444] CR2: 00007f83ba6c3ce0 CR3: 000000007d0e1000 CR4: 00000000000006f0
[ 75.453444] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 75.453444] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 75.453444] Process minicom (pid: 2127, threadinfo
ffff88007d05e000, task ffff88007dd33da0)
[ 75.453444] Stack:
[ 75.453444] 656369766564646a 0000000000000000 ffff88007dead000
ffff88007dead000
[ 75.453444] <0> 0000000000000000 0000000000000010 ffff88007d05fb38
ffffffff812a77b2
[ 75.453444] <0> ffff88007d05fbc8 ffffffffa0072e19 0000000000000282
ffff88007d2f7000
[ 75.453444] Call Trace:
[ 75.453444] [<ffffffff812a77b2>] usb_autopm_get_interface+0xe/0x10
[ 75.453444] [<ffffffffa0072e19>] acm_port_down+0x3f/0x1bb [cdc_acm]
[ 75.453444] [<ffffffff811f0af1>] ? tty_port_close_start+0xc1/0x153
[ 75.453444] [<ffffffffa0073258>] acm_tty_close+0x3d/0x83 [cdc_acm]
[ 75.453444] [<ffffffff811eaca7>] tty_release_dev+0x1bf/0x4e8
[ 75.453444] [<ffffffffa00732c3>] ? acm_tty_open+0x25/0x2ae [cdc_acm]
[ 75.453444] [<ffffffff8141e0f2>] ? mutex_unlock+0x9/0xb
[ 75.453444] [<ffffffffa00734fc>] ? acm_tty_open+0x25e/0x2ae [cdc_acm]
[ 75.453444] [<ffffffff811e8346>] ? check_tty_count+0x21/0xac
[ 75.453444] [<ffffffff811eb55d>] tty_open+0x33c/0x427
[ 75.453444] [<ffffffff810c3a81>] chrdev_open+0x150/0x16f
[ 75.453444] [<ffffffff8141fba7>] ? _spin_unlock+0x26/0x2a
[ 75.453444] [<ffffffff810c1a44>] ? file_move+0x1e/0x50
[ 75.453444] [<ffffffff810c3931>] ? chrdev_open+0x0/0x16f
[ 75.453444] [<ffffffff810bf594>] __dentry_open+0x150/0x26f
[ 75.453444] [<ffffffff810bf780>] nameidata_to_filp+0x41/0x52
[ 75.453444] [<ffffffff810cc55e>] do_filp_open+0x4ee/0x9ce
[ 75.453444] [<ffffffff810d5700>] ? alloc_fd+0x11d/0x12e
[ 75.453444] [<ffffffff810bf359>] do_sys_open+0x5d/0x10b
[ 75.453444] [<ffffffff810bf430>] sys_open+0x1b/0x1d
[ 75.453444] [<ffffffff8100baab>] system_call_fastpath+0x16/0x1b
[ 75.453444] Code: 56 41 55 41 54 49 89 fc 53 bb ed ff ff ff 48 83
ec 08 4c 8b 77 30 49 8d 86 08 05 00 00 4d 8d ae 70 ff ff ff 48 89 45
d0 48 89 c7 <41> 0f b6 b5 6b 03 00 00 e8 00 6e 17 00 41 83 7c 24 24 00
0f 84
[ 75.453444] RIP [<ffffffff812a76e1>] usb_autopm_do_interface+0x35/0xeb
[ 75.453444] RSP <ffff88007d05faf8>
[ 75.455529] ---[ end trace 03be7af14b545501 ]---
Full dmesg attached.
The later kernels have multiple oopses in a row and lock hard, so I
could not get
the oopses for something more recent than "something past 2.6.31-rc2".
I'll try to bisect, by it'll take some time.
[-- Attachment #2: crash --]
[-- Type: application/octet-stream, Size: 54524 bytes --]
[ 0.000000] Linux version 2.6.31-rc2-t (raa@blimp) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #64 SMP Mon Jul 13 20:52:55 CEST 2009
[ 0.000000] Command line: ro root=/dev/sda2 resume=/dev/sda3 snd-hda-intel.model=dell-3stack loglevel=7 rootfstype=ext4 no_console_suspend init=/boot/linuxrc-t
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f66d800 (usable)
[ 0.000000] BIOS-e820: 000000007f66d800 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x7f66d max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07F800000 mask FFF800000 uncachable
[ 0.000000] 2 base 07F700000 mask FFFF00000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f66d000
[ 0.000000] 0000000000 - 007f600000 page 2M
[ 0.000000] 007f600000 - 007f66d000 page 4k
[ 0.000000] kernel direct mapping tables up to 7f66d000 @ 8000-c000
[ 0.000000] ACPI: RSDP 00000000000fbc00 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 000000007f66f200 00054 (v01 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: FACP 000000007f66f09c 000F4 (v04 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: DSDT 000000007f66f800 05733 (v02 INT430 SYSFexxx 00001001 INTL 20050624)
[ 0.000000] ACPI: FACS 000000007f67e000 00040
[ 0.000000] ACPI: HPET 000000007f66f300 00038 (v01 DELL M08 00000001 ASL 00000061)
[ 0.000000] ACPI: APIC 000000007f66f400 00068 (v01 DELL M08 27D80B13 ASL 00000047)
[ 0.000000] ACPI: MCFG 000000007f66f3c0 0003E (v16 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: BOOT 000000007f66efc0 00028 (v01 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: SSDT 000000007f66d9b8 004CC (v01 PmRef CpuPm 00003000 INTL 20050624)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 007f66d000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001e30fb0] TEXT DATA BSS ==> [0001000000 - 0001e30fb0]
[ 0.000000] #3 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #4 [0001e31000 - 0001e311ec] BRK ==> [0001e31000 - 0001e311ec]
[ 0.000000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880002400000-ffff880003ffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007f66d
[ 0.000000] On node 0 totalpages: 521740
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 102 pages reserved
[ 0.000000] DMA zone: 3841 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7079 pages used for memmap
[ 0.000000] DMA32 zone: 510662 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
[ 0.000000] NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages at ffff880001e56000, static data 87328 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514503
[ 0.000000] Kernel command line: ro root=/dev/sda2 resume=/dev/sda3 snd-hda-intel.model=dell-3stack loglevel=7 rootfstype=ext4 no_console_suspend init=/boot/linuxrc-t
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 2039640k/2087348k available (4235k kernel code, 388k absent, 46740k reserved, 2343k data, 400k init)
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:320
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1995.127 MHz processor.
[ 0.002154] Console: colour VGA+ 80x25
[ 0.002160] console [tty0] enabled
[ 0.003333] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.003333] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.003333] ... MAX_LOCK_DEPTH: 48
[ 0.003333] ... MAX_LOCKDEP_KEYS: 8191
[ 0.003333] ... CLASSHASH_SIZE: 4096
[ 0.003333] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.003333] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.003333] ... CHAINHASH_SIZE: 16384
[ 0.003333] memory used by lock dependency info: 5695 kB
[ 0.003333] per task-struct memory footprint: 1920 bytes
[ 0.003333] hpet clockevent registered
[ 0.003333] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 3991.51 BogoMIPS (lpj=6650423)
[ 0.003333] Security Framework initialized
[ 0.003333] Mount-cache hash table entries: 256
[ 0.003333] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.003333] CPU: L2 cache: 2048K
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 0
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] CPU0: Thermal monitoring enabled (TM2)
[ 0.003333] using mwait in idle threads.
[ 0.003333] Performance Counters: Core2 events, Intel PMU driver.
[ 0.003333] ... version: 2
[ 0.003333] ... bit width: 40
[ 0.003333] ... generic counters: 2
[ 0.003333] ... value mask: 000000ffffffffff
[ 0.003333] ... max period: 000000007fffffff
[ 0.003333] ... fixed-purpose counters: 3
[ 0.003333] ... counter mask: 0000000700000003
[ 0.003333] ACPI: Core revision 20090521
[ 0.010100] Setting APIC routing to flat
[ 0.010527] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.045024] CPU0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.046666] lockdep: fixing up alternatives.
[ 0.046666] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.003333] Initializing CPU#1
[ 0.003333] Calibrating delay using timer specific routine.. 3991.24 BogoMIPS (lpj=6649994)
[ 0.003333] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.003333] CPU: L2 cache: 2048K
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 1
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] CPU1: Thermal monitoring enabled (TM2)
[ 0.003333] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.137951] CPU1: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.138212] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.140044] Brought up 2 CPUs
[ 0.140069] Total of 2 processors activated (7983.76 BogoMIPS).
[ 0.140165] CPU0 attaching sched-domain:
[ 0.140168] domain 0: span 0-1 level MC
[ 0.140171] groups: 0 1
[ 0.140178] CPU1 attaching sched-domain:
[ 0.140180] domain 0: span 0-1 level MC
[ 0.140183] groups: 1 0
[ 0.140274] NET: Registered protocol family 16
[ 0.143354] ACPI: bus type pci registered
[ 0.143390] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.143400] PCI: MCFG area at f8000000 reserved in E820
[ 0.144693] PCI: Using MMCONFIG at f8000000 - fbffffff
[ 0.144718] PCI: Using configuration type 1 for base access
[ 0.150092] bio: create slab <bio-0> at 0
[ 0.155048] ACPI: EC: Look up EC in DSDT
[ 0.172761] ACPI: SSDT 000000007f67e080 00043 (v01 LMPWR DELLLOM 00001001 INTL 20050624)
[ 0.189428] ACPI: Interpreter enabled
[ 0.189454] ACPI: (supports S0 S3 S4 S5)
[ 0.191782] ACPI: Using IOAPIC for interrupt routing
[ 0.237153] ACPI: No dock devices found.
[ 0.258520] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.258610] pci 0000:00:02.0: reg 10 64bit mmio: [0xf6e00000-0xf6efffff]
[ 0.258610] pci 0000:00:02.0: reg 18 64bit mmio: [0xe0000000-0xefffffff]
[ 0.258610] pci 0000:00:02.0: reg 20 io port: [0xeff8-0xefff]
[ 0.258610] pci 0000:00:02.1: reg 10 64bit mmio: [0xf6f00000-0xf6ffffff]
[ 0.258610] pci 0000:00:1a.0: reg 20 io port: [0x6f20-0x6f3f]
[ 0.258610] pci 0000:00:1a.1: reg 20 io port: [0x6f00-0x6f1f]
[ 0.258610] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfed1c400-0xfed1c7ff]
[ 0.258610] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.258610] pci 0000:00:1a.7: PME# disabled
[ 0.258610] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf6dfc000-0xf6dfffff]
[ 0.258610] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.258610] pci 0000:00:1b.0: PME# disabled
[ 0.258610] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.258610] pci 0000:00:1c.0: PME# disabled
[ 0.258610] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.258610] pci 0000:00:1c.1: PME# disabled
[ 0.258610] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.258610] pci 0000:00:1c.3: PME# disabled
[ 0.260116] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.260146] pci 0000:00:1c.5: PME# disabled
[ 0.260246] pci 0000:00:1d.0: reg 20 io port: [0x6f80-0x6f9f]
[ 0.260328] pci 0000:00:1d.1: reg 20 io port: [0x6f60-0x6f7f]
[ 0.260410] pci 0000:00:1d.2: reg 20 io port: [0x6f40-0x6f5f]
[ 0.260501] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfed1c000-0xfed1c3ff]
[ 0.260580] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.260611] pci 0000:00:1d.7: PME# disabled
[ 0.260841] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.260882] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.260912] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0900 (mask 007f)
[ 0.260954] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0c80 (mask 003f)
[ 0.261056] pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
[ 0.261066] pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
[ 0.261076] pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
[ 0.261085] pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
[ 0.261095] pci 0000:00:1f.1: reg 20 io port: [0x6fa0-0x6faf]
[ 0.261189] pci 0000:00:1f.2: reg 10 io port: [0x6eb0-0x6eb7]
[ 0.261198] pci 0000:00:1f.2: reg 14 io port: [0x6eb8-0x6ebb]
[ 0.261208] pci 0000:00:1f.2: reg 18 io port: [0x6ec0-0x6ec7]
[ 0.261218] pci 0000:00:1f.2: reg 1c io port: [0x6ec8-0x6ecb]
[ 0.261228] pci 0000:00:1f.2: reg 20 io port: [0x6ee0-0x6eff]
[ 0.261238] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf6dfb800-0xf6dfbfff]
[ 0.261292] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.261321] pci 0000:00:1f.2: PME# disabled
[ 0.261384] pci 0000:00:1f.3: reg 10 32bit mmio: [0xf6dfb700-0xf6dfb7ff]
[ 0.261416] pci 0000:00:1f.3: reg 20 io port: [0x10c0-0x10df]
[ 0.261752] pci 0000:0c:00.0: reg 10 32bit mmio: [0xf6cff000-0xf6cfffff]
[ 0.262013] pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
[ 0.262050] pci 0000:0c:00.0: PME# disabled
[ 0.262185] pci 0000:0c:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.262472] pci 0000:00:1c.1: bridge 32bit mmio: [0xf6c00000-0xf6cfffff]
[ 0.262573] pci 0000:00:1c.3: bridge io port: [0xd000-0xdfff]
[ 0.262579] pci 0000:00:1c.3: bridge 32bit mmio: [0xf6a00000-0xf6bfffff]
[ 0.262589] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
[ 0.262796] pci 0000:09:00.0: reg 10 64bit mmio: [0xf69f0000-0xf69fffff]
[ 0.263053] pci 0000:09:00.0: PME# supported from D3hot D3cold
[ 0.263089] pci 0000:09:00.0: PME# disabled
[ 0.263680] pci 0000:00:1c.5: bridge 32bit mmio: [0xf6900000-0xf69fffff]
[ 0.263746] pci 0000:03:01.0: reg 10 32bit mmio: [0xf68ff800-0xf68fffff]
[ 0.263820] pci 0000:03:01.0: supports D1 D2
[ 0.263822] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.263853] pci 0000:03:01.0: PME# disabled
[ 0.265733] pci 0000:03:01.1: reg 10 32bit mmio: [0xf68ff400-0xf68ff4ff]
[ 0.265806] pci 0000:03:01.1: supports D1 D2
[ 0.265809] pci 0000:03:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.265839] pci 0000:03:01.1: PME# disabled
[ 0.265915] pci 0000:03:01.2: reg 10 32bit mmio: [0xf68ff500-0xf68ff5ff]
[ 0.265989] pci 0000:03:01.2: supports D1 D2
[ 0.265991] pci 0000:03:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.266022] pci 0000:03:01.2: PME# disabled
[ 0.266097] pci 0000:03:01.3: reg 10 32bit mmio: [0xf68ff600-0xf68ff6ff]
[ 0.266171] pci 0000:03:01.3: supports D1 D2
[ 0.266174] pci 0000:03:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.266205] pci 0000:03:01.3: PME# disabled
[ 0.266282] pci 0000:03:01.4: reg 10 32bit mmio: [0xf68ff700-0xf68ff7ff]
[ 0.266357] pci 0000:03:01.4: supports D1 D2
[ 0.266360] pci 0000:03:01.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.266390] pci 0000:03:01.4: PME# disabled
[ 0.266509] pci 0000:00:1e.0: transparent bridge
[ 0.266541] pci 0000:00:1e.0: bridge 32bit mmio: [0xf6800000-0xf68fffff]
[ 0.266589] pci_bus 0000:00: on NUMA node 0
[ 0.266595] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.266983] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.267183] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.267280] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.267384] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.267484] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.284185] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.286708] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.286914] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *4
[ 0.287128] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.287349] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.287628] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.287904] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
[ 0.288164] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.288386] SCSI subsystem initialized
[ 0.288386] libata version 3.00 loaded.
[ 0.288386] usbcore: registered new interface driver usbfs
[ 0.288386] usbcore: registered new interface driver hub
[ 0.288386] usbcore: registered new device driver usb
[ 0.288386] PCI: Using ACPI for IRQ routing
[ 0.336703] cfg80211: Using static regulatory domain info
[ 0.336718] cfg80211: Regulatory domain: US
[ 0.336741] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 0.336779] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 0.336807] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.336835] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.336863] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.336890] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.336918] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 0.336973] cfg80211: Calling CRDA for country: US
[ 0.337011] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.337011] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.356679] pnp: PnP ACPI init
[ 0.356730] ACPI: bus type pnp registered
[ 0.378013] pnp 00:09: io resource (0x1000-0x1005) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.378057] pnp 00:09: io resource (0x1008-0x100f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.378281] pnp 00:0a: io resource (0x1006-0x1007) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.378323] pnp 00:0a: io resource (0x100a-0x1059) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.378365] pnp 00:0a: io resource (0x1060-0x107f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.378406] pnp 00:0a: io resource (0x1010-0x102f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.401334] pnp: PnP ACPI: found 12 devices
[ 0.401359] ACPI: ACPI bus type pnp unregistered
[ 0.401399] system 00:05: ioport range 0xc80-0xcff could not be reserved
[ 0.401435] system 00:08: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.401469] system 00:09: ioport range 0x900-0x97f has been reserved
[ 0.401497] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 0.401531] system 00:0a: ioport range 0xf400-0xf4fe has been reserved
[ 0.401559] system 00:0a: ioport range 0x1080-0x10bf has been reserved
[ 0.401587] system 00:0a: ioport range 0x10c0-0x10df has been reserved
[ 0.401615] system 00:0a: ioport range 0x809-0x809 has been reserved
[ 0.401649] system 00:0b: iomem range 0x0-0x9efff could not be reserved
[ 0.401677] system 00:0b: iomem range 0x9f000-0x9ffff could not be reserved
[ 0.401706] system 00:0b: iomem range 0xc0000-0xcffff has been reserved
[ 0.401734] system 00:0b: iomem range 0xe0000-0xfffff has been reserved
[ 0.401762] system 00:0b: iomem range 0x100000-0x7f66d7ff could not be reserved
[ 0.401801] system 00:0b: iomem range 0x7f66d800-0x7f6fffff has been reserved
[ 0.401830] system 00:0b: iomem range 0x7f700000-0x7f7fffff has been reserved
[ 0.401859] system 00:0b: iomem range 0x7f700000-0x7fefffff could not be reserved
[ 0.401897] system 00:0b: iomem range 0xffe00000-0xffffffff has been reserved
[ 0.401926] system 00:0b: iomem range 0xffa00000-0xffbfffff has been reserved
[ 0.401955] system 00:0b: iomem range 0xfec00000-0xfec0ffff has been reserved
[ 0.401984] system 00:0b: iomem range 0xfee00000-0xfee0ffff has been reserved
[ 0.402013] system 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.402041] system 00:0b: iomem range 0xfeda0000-0xfeda3fff has been reserved
[ 0.402070] system 00:0b: iomem range 0xfeda4000-0xfeda4fff has been reserved
[ 0.402099] system 00:0b: iomem range 0xfeda5000-0xfeda5fff has been reserved
[ 0.402128] system 00:0b: iomem range 0xfeda6000-0xfeda6fff has been reserved
[ 0.402157] system 00:0b: iomem range 0xfed18000-0xfed1bfff has been reserved
[ 0.402185] system 00:0b: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.407629] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:0b
[ 0.407656] pci 0000:00:1c.0: IO window: disabled
[ 0.407686] pci 0000:00:1c.0: MEM window: disabled
[ 0.407714] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.407743] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0c
[ 0.407769] pci 0000:00:1c.1: IO window: disabled
[ 0.407800] pci 0000:00:1c.1: MEM window: 0xf6c00000-0xf6cfffff
[ 0.407829] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.407858] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0d
[ 0.407887] pci 0000:00:1c.3: IO window: 0xd000-0xdfff
[ 0.407917] pci 0000:00:1c.3: MEM window: 0xf6a00000-0xf6bfffff
[ 0.407948] pci 0000:00:1c.3: PREFETCH window: 0x000000f0000000-0x000000f01fffff
[ 0.407993] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:09
[ 0.408019] pci 0000:00:1c.5: IO window: disabled
[ 0.408049] pci 0000:00:1c.5: MEM window: 0xf6900000-0xf69fffff
[ 0.408079] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.408108] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[ 0.408134] pci 0000:00:1e.0: IO window: disabled
[ 0.408164] pci 0000:00:1e.0: MEM window: 0xf6800000-0xf68fffff
[ 0.408193] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.408236] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.408268] pci 0000:00:1c.0: setting latency timer to 64
[ 0.408282] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.408313] pci 0000:00:1c.1: setting latency timer to 64
[ 0.408326] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.408357] pci 0000:00:1c.3: setting latency timer to 64
[ 0.408368] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.408399] pci 0000:00:1c.5: setting latency timer to 64
[ 0.408409] pci 0000:00:1e.0: setting latency timer to 64
[ 0.408415] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.408418] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.408422] pci_bus 0000:0c: resource 1 mem: [0xf6c00000-0xf6cfffff]
[ 0.408425] pci_bus 0000:0d: resource 0 io: [0xd000-0xdfff]
[ 0.408428] pci_bus 0000:0d: resource 1 mem: [0xf6a00000-0xf6bfffff]
[ 0.408430] pci_bus 0000:0d: resource 2 pref mem [0xf0000000-0xf01fffff]
[ 0.408433] pci_bus 0000:09: resource 1 mem: [0xf6900000-0xf69fffff]
[ 0.408436] pci_bus 0000:03: resource 1 mem: [0xf6800000-0xf68fffff]
[ 0.408439] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.408442] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.408496] NET: Registered protocol family 2
[ 0.408701] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.409409] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.411333] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
[ 0.415011] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.415081] TCP reno registered
[ 0.415279] NET: Registered protocol family 1
[ 0.415551] Simple Boot Flag at 0x79 set to 0x1
[ 0.417781] cpu0(2) debug files 152
[ 0.419898] cpu1(2) debug files 152
[ 0.426065] msgmni has been set to 3984
[ 0.426581] alg: No test for stdrng (krng)
[ 0.426622] io scheduler noop registered
[ 0.426724] io scheduler cfq registered (default)
[ 0.426763] pci 0000:00:02.0: Boot video device
[ 0.427296] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.427311] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.427645] pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.427658] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 0.427984] pcieport-driver 0000:00:1c.3: irq 26 for MSI/MSI-X
[ 0.427998] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 0.428330] pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X
[ 0.428344] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.428689] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.429042] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.429069] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.429219] acpiphp_glue: can't get bus number, assuming 0
[ 0.429548] decode_hpp: Could not get hotplug parameters. Use defaults
[ 0.429681] acpiphp: Slot [1] registered
[ 0.429854] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.429954] Platform driver 'platform-lcd' needs updating - please use dev_pm_ops
[ 0.430475] ACPI: AC Adapter [AC] (on-line)
[ 0.430754] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 0.431266] ACPI: Lid Switch [LID]
[ 0.431405] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.431449] ACPI: Power Button [PBTN]
[ 0.431584] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 0.431624] ACPI: Sleep Button [SBTN]
[ 0.432320] ACPI: SSDT 000000007f66e4ee 00286 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
[ 0.433106] ACPI: SSDT 000000007f66de84 005E5 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
[ 0.433794] Monitor-Mwait will be used to enter C-1 state
[ 0.433830] Monitor-Mwait will be used to enter C-2 state
[ 0.433860] Monitor-Mwait will be used to enter C-3 state
[ 0.433868] Marking TSC unstable due to TSC halts in idle
[ 0.433924] Switched to high resolution mode on CPU 0
[ 0.434028] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 0.434198] processor LNXCPU:00: registered as cooling_device0
[ 0.434228] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.434677] ACPI: SSDT 000000007f66e774 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
[ 0.434948] Switched to high resolution mode on CPU 1
[ 0.435307] ACPI: SSDT 000000007f66e469 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
[ 0.436166] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 0.436293] processor LNXCPU:01: registered as cooling_device1
[ 0.436323] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.444673] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.444712] ACPI: Thermal Zone [THM] (56 C)
[ 0.444941] ACPI: Battery Slot [BAT0] (battery absent)
[ 0.449937] Linux agpgart interface v0.103
[ 0.449985] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 0.450601] agpgart-intel 0000:00:00.0: detected 7676K stolen memory
[ 0.453173] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 0.453366] [drm] Initialized drm 1.1.0 20060810
[ 0.453415] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.453445] i915 0000:00:02.0: setting latency timer to 64
[ 0.461712] i915 0000:00:02.0: irq 28 for MSI/MSI-X
[ 1.343518] [drm] LVDS-8: set mode 1280x800 10
[ 1.892646] Console: switching to colour frame buffer device 160x50
[ 1.895493] [drm] fb0: inteldrmfb frame buffer device
[ 1.910282] acpi device:37: registered as cooling_device2
[ 1.910890] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:34/input/input3
[ 1.910948] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 1.911053] ACPI Warning: \_SB_.PCI0.VID2._DOD: Return Package has no elements (empty) 20090521 nspredef-434
[ 1.911250] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:39/input/input4
[ 1.911304] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 1.911409] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 1.911788] ahci 0000:00:1f.2: version 3.0
[ 1.911804] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.911893] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[ 1.911972] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
[ 1.912020] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems
[ 1.912066] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.917584] scsi0 : ahci
[ 1.917834] scsi1 : ahci
[ 1.918016] scsi2 : ahci
[ 1.918416] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 29
[ 1.918460] ata2: DUMMY
[ 1.918477] ata3: SATA max UDMA/133 abar m2048@0xf6dfb800 port 0xf6dfba00 irq 29
[ 1.918665] ata_piix 0000:00:1f.1: version 2.13
[ 1.918675] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.918759] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.918864] scsi3 : ata_piix
[ 1.919065] scsi4 : ata_piix
[ 1.919891] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x6fa0 irq 14
[ 1.919929] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x6fa8 irq 15
[ 1.920116] tg3.c:v3.99 (April 20, 2009)
[ 1.920174] tg3 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.921135] tg3 0000:09:00.0: setting latency timer to 64
[ 1.921423] ata5: port disabled. ignoring.
[ 1.927546] tg3 0000:09:00.0: PME# disabled
[ 2.080403] ata4.00: ATAPI: HL-DT-ST DVDRW GSA-S10N, A100, max UDMA/33
[ 2.093639] ata4.00: configured for UDMA/33
[ 2.185444] eth0: Tigon3 [partno(BCM95906) rev c002] (PCI Express) MAC address 00:1d:09:35:87:70
[ 2.186521] eth0: attached PHY is 5906 (10/100Base-TX Ethernet) (WireSpeed[0])
[ 2.187655] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0]
[ 2.188797] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 2.190037] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 2.191246] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 2.192595] iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.193879] iwl3945 0000:0c:00.0: setting latency timer to 64
[ 2.264773] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.266113] iwl3945 0000:0c:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 2.267465] iwl3945 0000:0c:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 2.269010] iwl3945 0000:0c:00.0: irq 30 for MSI/MSI-X
[ 2.270250] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 2.270981] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.272421] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 2.273895] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.273900] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.275410] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 2.280825] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.282336] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.282369] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
[ 2.297515] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 2.299108] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.300674] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.302285] usb usb1: Product: EHCI Host Controller
[ 2.303903] usb usb1: Manufacturer: Linux 2.6.31-rc2-t ehci_hcd
[ 2.305532] usb usb1: SerialNumber: 0000:00:1a.7
[ 2.307276] usb usb1: configuration #1 chosen from 1 choice
[ 2.309011] hub 1-0:1.0: USB hub found
[ 2.310612] hub 1-0:1.0: 4 ports detected
[ 2.312370] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.313962] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.313966] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.315559] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.321019] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.322529] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.322551] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
[ 2.337515] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.339024] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.340523] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.342020] usb usb2: Product: EHCI Host Controller
[ 2.343484] usb usb2: Manufacturer: Linux 2.6.31-rc2-t ehci_hcd
[ 2.345009] usb usb2: SerialNumber: 0000:00:1d.7
[ 2.346624] usb usb2: configuration #1 chosen from 1 choice
[ 2.348189] hub 2-0:1.0: USB hub found
[ 2.349655] hub 2-0:1.0: 6 ports detected
[ 2.351308] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.352887] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.354346] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.354351] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.355809] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.357306] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
[ 2.358843] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.360306] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.361775] usb usb3: Product: UHCI Host Controller
[ 2.363219] usb usb3: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 2.364691] usb usb3: SerialNumber: 0000:00:1a.0
[ 2.366218] usb usb3: configuration #1 chosen from 1 choice
[ 2.367698] hub 3-0:1.0: USB hub found
[ 2.369105] hub 3-0:1.0: 2 ports detected
[ 2.370612] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.372027] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.372031] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.373417] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.374840] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
[ 2.376230] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.377575] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.378899] usb usb4: Product: UHCI Host Controller
[ 2.380207] usb usb4: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 2.381544] usb usb4: SerialNumber: 0000:00:1a.1
[ 2.382962] usb usb4: configuration #1 chosen from 1 choice
[ 2.384360] hub 4-0:1.0: USB hub found
[ 2.385666] hub 4-0:1.0: 2 ports detected
[ 2.387100] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.388438] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.388442] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.389803] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.391173] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
[ 2.392541] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.393849] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.395188] usb usb5: Product: UHCI Host Controller
[ 2.396517] usb usb5: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 2.397881] usb usb5: SerialNumber: 0000:00:1d.0
[ 2.399333] usb usb5: configuration #1 chosen from 1 choice
[ 2.400745] hub 5-0:1.0: USB hub found
[ 2.402074] hub 5-0:1.0: 2 ports detected
[ 2.403512] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 2.404865] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.404869] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.406218] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.407604] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
[ 2.408992] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.410320] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.411703] usb usb6: Product: UHCI Host Controller
[ 2.413037] usb usb6: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 2.414386] usb usb6: SerialNumber: 0000:00:1d.1
[ 2.415883] usb usb6: configuration #1 chosen from 1 choice
[ 2.417288] hub 6-0:1.0: USB hub found
[ 2.418627] hub 6-0:1.0: 2 ports detected
[ 2.420107] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 2.421477] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.421481] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.422839] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.424231] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
[ 2.425621] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.426958] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.428316] usb usb7: Product: UHCI Host Controller
[ 2.429668] usb usb7: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 2.431020] usb usb7: SerialNumber: 0000:00:1d.2
[ 2.432462] usb usb7: configuration #1 chosen from 1 choice
[ 2.433870] hub 7-0:1.0: USB hub found
[ 2.435215] hub 7-0:1.0: 2 ports detected
[ 2.436758] Initializing USB Mass Storage driver...
[ 2.438202] usbcore: registered new interface driver usb-storage
[ 2.439532] USB Mass Storage support registered.
[ 2.440960] usbcore: registered new interface driver libusual
[ 2.442359] usbcore: registered new interface driver ums-alauda
[ 2.443737] usbcore: registered new interface driver ums-cypress
[ 2.445099] usbcore: registered new interface driver ums-datafab
[ 2.446443] usbcore: registered new interface driver ums-freecom
[ 2.447787] usbcore: registered new interface driver ums-isd200
[ 2.449098] usbcore: registered new interface driver ums-jumpshot
[ 2.450407] usbcore: registered new interface driver ums-karma
[ 2.451695] usbcore: registered new interface driver ums-sddr09
[ 2.452958] usbcore: registered new interface driver ums-sddr55
[ 2.454230] usbcore: registered new interface driver ums-usbat
[ 2.455552] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.456754] Platform driver 'i8042' needs updating - please use dev_pm_ops
[ 2.461380] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.462580] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.463893] mice: PS/2 mouse device common for all mice
[ 2.465648] rtc_cmos 00:03: RTC can wake from S4
[ 2.466985] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.468203] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 2.469450] i2c /dev entries driver
[ 2.470900] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 2.471191] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 2.473461] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 2.474901] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 2.476225] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.477472] iTCO_vendor_support: vendor-support=0
[ 2.479132] cpuidle: using governor ladder
[ 2.481246] cpuidle: using governor menu
[ 2.482498] sdhci: Secure Digital Host Controller Interface driver
[ 2.483744] sdhci: Copyright(c) Pierre Ossman
[ 2.485008] sdhci-pci 0000:03:01.1: SDHCI controller found [1180:0822] (rev 22)
[ 2.486254] sdhci-pci 0000:03:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 2.489753] Registered led device: mmc0::
[ 2.492145] mmc0: SDHCI controller on PCI [0000:03:01.1] using DMA
[ 2.493501] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 2.494755] ricoh-mmc: Copyright(c) Philip Langdale
[ 2.496031] ricoh-mmc: Ricoh MMC controller found at 0000:03:01.2 [1180:0843] (rev 12)
[ 2.497344] ricoh-mmc: Controller is now disabled.
[ 2.498861] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 2.501889] usbcore: registered new interface driver hiddev
[ 2.503250] usbcore: registered new interface driver usbhid
[ 2.504548] usbhid: v2.6:USB HID core driver
[ 2.508010] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 2.509523] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 2.510933] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 2.657603] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.714610] ata1.00: ATA-8: WDC WD1200BEVS-75UST0, 01.01A01, max UDMA/133
[ 2.715998] ata1.00: 234441648 sectors, multi 8: LBA48 NCQ (depth 31/32)
[ 2.718230] ata1.00: configured for UDMA/133
[ 2.730299] scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVS-7 01.0 PQ: 0 ANSI: 5
[ 2.732189] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 2.733601] sd 0:0:0:0: [sda] Write Protect is off
[ 2.734980] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.735016] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.736630] sda:
[ 2.736931] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.742975] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRW GSA-S10N A100 PQ: 0 ANSI: 5
[ 2.744574] sda1 sda2 sda3 sda4 <sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda caddy
[ 2.754818] Uniform CD-ROM driver Revision: 3.20
[ 2.756636] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.756856] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 2.759414] sda5 sda6 >
[ 2.768990] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.814517] mmc0: new high speed SD card at address 0002
[ 2.816386] mmcblk0: mmc0:0002 00000 1.88 GiB
[ 2.818034] usb 2-6: new high speed USB device using ehci_hcd and address 4
[ 2.818055] mmcblk0: p1
[ 2.853640] input: HDA Intel Line In at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 2.855546] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 2.857459] input: HDA Intel Mic at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 2.859396] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 2.861309] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 2.863179] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 2.865018] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 2.866825] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 2.869210] ALSA device list:
[ 2.870785] #0: HDA Intel at 0xf6dfc000 irq 21
[ 2.872387] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 2.874316] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 2.875907] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 2.877544] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 2.880110] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.881730] TCP cubic registered
[ 2.883877] NET: Registered protocol family 10
[ 2.886538] lo: Disabled Privacy Extensions
[ 2.890207] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.891802] NET: Registered protocol family 17
[ 2.893421] lib80211: common routines for IEEE802.11 drivers
[ 2.895018] lib80211_crypt: registered algorithm 'NULL'
[ 2.905117] rtc_cmos 00:03: setting system clock to 2009-08-02 13:13:38 UTC (1249218818)
[ 2.908684] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 2.912598] Initalizing network drop monitor service
[ 2.946622] usb 2-6: New USB device found, idVendor=05a9, idProduct=7670
[ 2.950247] usb 2-6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.953820] usb 2-6: Product: Laptop Integrated Webcam
[ 2.957359] usb 2-6: Manufacturer: OmniVision Technologies, Inc. -7670-07.09.28.1
[ 2.961370] usb 2-6: configuration #1 chosen from 1 choice
[ 3.000965] Clocksource tsc unstable (delta = -194746226 ns)
[ 3.143858] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps: 0xa04753/0x200000
[ 3.185185] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input14
[ 3.190099] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 3.231365] EXT4-fs (sda2): barriers enabled
[ 3.256225] kjournald2 starting: pid 827, dev sda2:8, commit interval 5 seconds
[ 3.256340] EXT4-fs (sda2): delayed allocation enabled
[ 3.256659] EXT4-fs: mballoc enabled
[ 3.256794] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 3.256922] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 3.256990] Freeing unused kernel memory: 400k freed
[ 3.257273] Write protecting the kernel read-only data: 6088k
[ 3.390677] usb 5-1: New USB device found, idVendor=1457, idProduct=5122
[ 3.394250] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.397666] usb 5-1: Product: RNDIS/Ethernet Gadget
[ 3.401092] usb 5-1: Manufacturer: Linux 2.6.24/s3c2410_udc
[ 3.438219] usb 5-1: configuration #1 chosen from 2 choices
[ 3.673546] usb 5-2: new low speed USB device using uhci_hcd and address 3
[ 3.845614] usb 5-2: New USB device found, idVendor=046d, idProduct=c016
[ 3.849082] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.852522] usb 5-2: Product: Optical USB Mouse
[ 3.855875] usb 5-2: Manufacturer: Logitech
[ 3.859912] usb 5-2: configuration #1 chosen from 1 choice
[ 3.879777] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input15
[ 3.883955] generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2/input0
[ 6.135910] Linux video capture interface: v2.00
[ 6.190596] ACPI: WMI: Mapper loaded
[ 6.205536] ohci1394 0000:03:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 6.230418] usb0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, a6:24:c4:e1:1e:80
[ 6.230756] usbcore: registered new interface driver cdc_ether
[ 6.263374] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[f68ff800-f68fffff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 6.281136] uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:7670)
[ 6.281647] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
[ 6.291633] input: Laptop Integrated Webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6:1.0/input/input16
[ 6.293843] usbcore: registered new interface driver uvcvideo
[ 6.293937] USB Video Class driver (v0.1.0)
[ 6.812598] SysRq : Changing Loglevel
[ 6.812681] Loglevel set to 9
[ 6.999658] Adding 4096564k swap on /dev/sda3. Priority:-1 extents:1 across:4096564k
[ 7.535287] ieee1394: Host added: ID:BUS[0-00:1023] GUID[354fc000321a4870]
[ 29.346931] usb 5-1: USB disconnect, address 2
[ 29.347343] usb0: unregister 'cdc_ether' usb-0000:00:1d.0-1, CDC Ethernet Device
[ 30.573530] usb 5-1: new full speed USB device using uhci_hcd and address 4
[ 30.750689] usb 5-1: New USB device found, idVendor=1457, idProduct=5119
[ 30.750795] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 30.750923] usb 5-1: Product: Neo1973 Bootloader U-Boot 1.3.2-rc2
[ 30.751005] usb 5-1: Manufacturer: OpenMoko, Inc
[ 30.751071] usb 5-1: SerialNumber: 0000000
[ 30.752032] usb 5-1: configuration #1 chosen from 2 choices
[ 30.793924] cdc_acm 5-1:1.0: This device cannot do calls on its own. It is not a modem.
[ 30.794103] cdc_acm 5-1:1.0: ttyACM0: USB ACM device
[ 30.799509] usbcore: registered new interface driver cdc_acm
[ 30.799610] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 47.346852] usb 5-1: USB disconnect, address 4
[ 47.352989] tty_port_close_start: count = -1
[ 48.358107] tty_port_close_start: count = -1
[ 49.362088] tty_port_close_start: count = -1
[ 50.365975] tty_port_close_start: count = -1
[ 51.369831] tty_port_close_start: count = -1
[ 52.373640] tty_port_close_start: count = -1
[ 53.377348] tty_port_close_start: count = -1
[ 54.381038] tty_port_close_start: count = -1
[ 55.384717] tty_port_close_start: count = -1
[ 56.388336] tty_port_close_start: count = -1
[ 57.391932] tty_port_close_start: count = -1
[ 58.395485] tty_port_close_start: count = -1
[ 59.399000] tty_port_close_start: count = -1
[ 60.400401] tty_port_close_start: count = -1
[ 61.401795] tty_port_close_start: count = -1
[ 62.405239] tty_port_close_start: count = -1
[ 63.408676] tty_port_close_start: count = -1
[ 64.412031] tty_port_close_start: count = -1
[ 65.415241] tty_port_close_start: count = -1
[ 66.418339] tty_port_close_start: count = -1
[ 67.421433] tty_port_close_start: count = -1
[ 68.424520] tty_port_close_start: count = -1
[ 69.427630] tty_port_close_start: count = -1
[ 70.430787] tty_port_close_start: count = -1
[ 71.433903] tty_port_close_start: count = -1
[ 72.437040] tty_port_close_start: count = -1
[ 73.440171] tty_port_close_start: count = -1
[ 74.441520] tty_port_close_start: count = -1
[ 75.073519] usb 5-1: new full speed USB device using uhci_hcd and address 5
[ 75.271699] usb 5-1: New USB device found, idVendor=1457, idProduct=5122
[ 75.271709] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 75.271716] usb 5-1: Product: RNDIS/Ethernet Gadget
[ 75.271722] usb 5-1: Manufacturer: Linux 2.6.24/s3c2410_udc
[ 75.272788] usb 5-1: configuration #1 chosen from 2 choices
[ 75.288865] usb0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, 1a:e0:cd:b1:57:c0
[ 75.442858] tty_port_close_start: count = -1
[ 75.442881] general protection fault: 0000 [#1] SMP
[ 75.444775] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1/uevent
[ 75.446041] CPU 0
[ 75.446041] Modules linked in: cdc_acm uvcvideo cdc_ether usbnet ohci1394 wmi videodev v4l1_compat v4l2_compat_ioctl32 ieee1394 mii
[ 75.446041] Pid: 2127, comm: minicom Not tainted 2.6.31-rc2-t #64 XPS M1330
[ 75.446041] RIP: 0010:[<ffffffff812a76e1>] [<ffffffff812a76e1>] usb_autopm_do_interface+0x35/0xeb
[ 75.453444] RSP: 0018:ffff88007d05faf8 EFLAGS: 00010292
[ 75.453444] RAX: 656369766564646a RBX: 00000000ffffffed RCX: 0000000000000000
[ 75.453444] RDX: ffffffffa00755b8 RSI: 0000000000000001 RDI: 656369766564646a
[ 75.453444] RBP: ffff88007d05fb28 R08: 0000000000000001 R09: 0000000000000000
[ 75.453444] R10: ffffffff810594a7 R11: 0000000000000082 R12: ffff88007c527800
[ 75.453444] R13: 6563697665645ed2 R14: 6563697665645f62 R15: 0000000000000001
[ 75.453444] FS: 00007fe65d7916f0(0000) GS:ffff880001e56000(0000) knlGS:0000000000000000
[ 75.453444] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 75.453444] CR2: 00007f83ba6c3ce0 CR3: 000000007d0e1000 CR4: 00000000000006f0
[ 75.453444] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 75.453444] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 75.453444] Process minicom (pid: 2127, threadinfo ffff88007d05e000, task ffff88007dd33da0)
[ 75.453444] Stack:
[ 75.453444] 656369766564646a 0000000000000000 ffff88007dead000 ffff88007dead000
[ 75.453444] <0> 0000000000000000 0000000000000010 ffff88007d05fb38 ffffffff812a77b2
[ 75.453444] <0> ffff88007d05fbc8 ffffffffa0072e19 0000000000000282 ffff88007d2f7000
[ 75.453444] Call Trace:
[ 75.453444] [<ffffffff812a77b2>] usb_autopm_get_interface+0xe/0x10
[ 75.453444] [<ffffffffa0072e19>] acm_port_down+0x3f/0x1bb [cdc_acm]
[ 75.453444] [<ffffffff811f0af1>] ? tty_port_close_start+0xc1/0x153
[ 75.453444] [<ffffffffa0073258>] acm_tty_close+0x3d/0x83 [cdc_acm]
[ 75.453444] [<ffffffff811eaca7>] tty_release_dev+0x1bf/0x4e8
[ 75.453444] [<ffffffffa00732c3>] ? acm_tty_open+0x25/0x2ae [cdc_acm]
[ 75.453444] [<ffffffff8141e0f2>] ? mutex_unlock+0x9/0xb
[ 75.453444] [<ffffffffa00734fc>] ? acm_tty_open+0x25e/0x2ae [cdc_acm]
[ 75.453444] [<ffffffff811e8346>] ? check_tty_count+0x21/0xac
[ 75.453444] [<ffffffff811eb55d>] tty_open+0x33c/0x427
[ 75.453444] [<ffffffff810c3a81>] chrdev_open+0x150/0x16f
[ 75.453444] [<ffffffff8141fba7>] ? _spin_unlock+0x26/0x2a
[ 75.453444] [<ffffffff810c1a44>] ? file_move+0x1e/0x50
[ 75.453444] [<ffffffff810c3931>] ? chrdev_open+0x0/0x16f
[ 75.453444] [<ffffffff810bf594>] __dentry_open+0x150/0x26f
[ 75.453444] [<ffffffff810bf780>] nameidata_to_filp+0x41/0x52
[ 75.453444] [<ffffffff810cc55e>] do_filp_open+0x4ee/0x9ce
[ 75.453444] [<ffffffff810d5700>] ? alloc_fd+0x11d/0x12e
[ 75.453444] [<ffffffff810bf359>] do_sys_open+0x5d/0x10b
[ 75.453444] [<ffffffff810bf430>] sys_open+0x1b/0x1d
[ 75.453444] [<ffffffff8100baab>] system_call_fastpath+0x16/0x1b
[ 75.453444] Code: 56 41 55 41 54 49 89 fc 53 bb ed ff ff ff 48 83 ec 08 4c 8b 77 30 49 8d 86 08 05 00 00 4d 8d ae 70 ff ff ff 48 89 45 d0 48 89 c7 <41> 0f b6 b5 6b 03 00 00 e8 00 6e 17 00 41 83 7c 24 24 00 0f 84
[ 75.453444] RIP [<ffffffff812a76e1>] usb_autopm_do_interface+0x35/0xeb
[ 75.453444] RSP <ffff88007d05faf8>
[ 75.455529] ---[ end trace 03be7af14b545501 ]---
[ 86.063423] EXT4-fs (sda5): barriers enabled
[ 86.077147] kjournald2 starting: pid 2382, dev sda5:8, commit interval 5 seconds
[ 86.077487] EXT4-fs (sda5): internal journal on sda5:8
[ 86.077496] EXT4-fs (sda5): delayed allocation enabled
[ 86.077503] EXT4-fs: file extents enabled
[ 86.077641] EXT4-fs: mballoc enabled
[ 86.077690] EXT4-fs (sda5): recovery complete
[ 86.094392] EXT4-fs (sda5): mounted filesystem with writeback data mode
[ 87.613479] hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x001f1500
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 16:40 Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet Alex Riesen
@ 2009-08-02 17:19 ` Oliver Neukum
2009-08-02 18:25 ` Alex Riesen
0 siblings, 1 reply; 11+ messages in thread
From: Oliver Neukum @ 2009-08-02 17:19 UTC (permalink / raw)
To: Alex Riesen
Cc: linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
Am Sonntag, 2. August 2009 18:40:56 schrieb Alex Riesen:
> [ 75.453444] Call Trace:
> [ 75.453444] [<ffffffff812a77b2>] usb_autopm_get_interface+0xe/0x10
> [ 75.453444] [<ffffffffa0072e19>] acm_port_down+0x3f/0x1bb [cdc_acm]
> [ 75.453444] [<ffffffff811f0af1>] ? tty_port_close_start+0xc1/0x153
> [ 75.453444] [<ffffffffa0073258>] acm_tty_close+0x3d/0x83 [cdc_acm]
> [ 75.453444] [<ffffffff811eaca7>] tty_release_dev+0x1bf/0x4e8
> [ 75.453444] [<ffffffffa00732c3>] ? acm_tty_open+0x25/0x2ae [cdc_acm]
This can happen only if acm_port_down() fails to detect that the device has
been disconnected, as it calls usb_autopm_get_interface()
only if acm->dev != NULL.
This however should not happen if acm_disconnect runs.
Can you put a printk into acm_disconnect and recompile with CONFIG_USB_DEBUG?
Regards
Oliver
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 17:19 ` Oliver Neukum
@ 2009-08-02 18:25 ` Alex Riesen
2009-08-02 20:39 ` Alex Riesen
0 siblings, 1 reply; 11+ messages in thread
From: Alex Riesen @ 2009-08-02 18:25 UTC (permalink / raw)
To: Oliver Neukum
Cc: linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
[-- Attachment #1: Type: text/plain, Size: 1381 bytes --]
On Sun, Aug 2, 2009 at 19:19, Oliver Neukum<oliver@neukum.org> wrote:
> Am Sonntag, 2. August 2009 18:40:56 schrieb Alex Riesen:
>> [ 75.453444] Call Trace:
>> [ 75.453444] [<ffffffff812a77b2>] usb_autopm_get_interface+0xe/0x10
>> [ 75.453444] [<ffffffffa0072e19>] acm_port_down+0x3f/0x1bb [cdc_acm]
>> [ 75.453444] [<ffffffff811f0af1>] ? tty_port_close_start+0xc1/0x153
>> [ 75.453444] [<ffffffffa0073258>] acm_tty_close+0x3d/0x83 [cdc_acm]
>> [ 75.453444] [<ffffffff811eaca7>] tty_release_dev+0x1bf/0x4e8
>> [ 75.453444] [<ffffffffa00732c3>] ? acm_tty_open+0x25/0x2ae [cdc_acm]
>
> This can happen only if acm_port_down() fails to detect that the device has
> been disconnected, as it calls usb_autopm_get_interface()
> only if acm->dev != NULL.
> This however should not happen if acm_disconnect runs.
>
> Can you put a printk into acm_disconnect and recompile with CONFIG_USB_DEBUG?
I put the printks at some random lines in acm_disconnect (as of v2.6.31-rc2)
and turned CONFIG_USB_DEBUG on. It is definitely not the same kernel
I tried before (and sadly, it does not go oops), but it still has
tty_port_close_start: count = -1
Dmesg attached
I'm retrying with recent kernels (hopefully I'll get enough data left
on the screen),
I shall try to find the -rc2 which oopses (I suspect it is the one
just before -rc3).
[-- Attachment #2: usbdeb --]
[-- Type: application/octet-stream, Size: 73122 bytes --]
[ 0.000000] Linux version 2.6.31-rc2-t (raa@blimp) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #98 SMP Sun Aug 2 19:59:12 CEST 2009
[ 0.000000] Command line: vga=ask ro root=/dev/sda2 resume=/dev/sda3 snd-hda-intel.model=dell-3stack loglevel=7 rootfstype=ext4 no_console_suspend init=/boot/linuxrc-t
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f66d800 (usable)
[ 0.000000] BIOS-e820: 000000007f66d800 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x7f66d max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07F800000 mask FFF800000 uncachable
[ 0.000000] 2 base 07F700000 mask FFFF00000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007f66d000
[ 0.000000] 0000000000 - 007f600000 page 2M
[ 0.000000] 007f600000 - 007f66d000 page 4k
[ 0.000000] kernel direct mapping tables up to 7f66d000 @ 8000-c000
[ 0.000000] ACPI: RSDP 00000000000fbc00 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 000000007f66f200 00054 (v01 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: FACP 000000007f66f09c 000F4 (v04 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: DSDT 000000007f66f800 05733 (v02 INT430 SYSFexxx 00001001 INTL 20050624)
[ 0.000000] ACPI: FACS 000000007f67e000 00040
[ 0.000000] ACPI: HPET 000000007f66f300 00038 (v01 DELL M08 00000001 ASL 00000061)
[ 0.000000] ACPI: APIC 000000007f66f400 00068 (v01 DELL M08 27D80B13 ASL 00000047)
[ 0.000000] ACPI: MCFG 000000007f66f3c0 0003E (v16 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: BOOT 000000007f66efc0 00028 (v01 DELL M08 27D80B13 ASL 00000061)
[ 0.000000] ACPI: SSDT 000000007f66d9b8 004CC (v01 PmRef CpuPm 00003000 INTL 20050624)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 007f66d000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001f0fa70] TEXT DATA BSS ==> [0001000000 - 0001f0fa70]
[ 0.000000] #3 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #4 [0001f10000 - 0001f101ec] BRK ==> [0001f10000 - 0001f101ec]
[ 0.000000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880002400000-ffff880003ffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007f66d
[ 0.000000] On node 0 totalpages: 521740
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 102 pages reserved
[ 0.000000] DMA zone: 3841 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7079 pages used for memmap
[ 0.000000] DMA32 zone: 510662 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
[ 0.000000] NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages at ffff880001f35000, static data 86944 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514503
[ 0.000000] Kernel command line: vga=ask ro root=/dev/sda2 resume=/dev/sda3 snd-hda-intel.model=dell-3stack loglevel=7 rootfstype=ext4 no_console_suspend init=/boot/linuxrc-t
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Memory: 2038872k/2087348k available (3966k kernel code, 388k absent, 47632k reserved, 2174k data, 388k init)
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] NR_IRQS:320
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1994.977 MHz processor.
[ 0.002901] Console: colour VGA+ 80x34
[ 0.002915] console [tty0] enabled
[ 0.003333] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.003333] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.003333] ... MAX_LOCK_DEPTH: 48
[ 0.003333] ... MAX_LOCKDEP_KEYS: 8191
[ 0.003333] ... CLASSHASH_SIZE: 4096
[ 0.003333] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.003333] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.003333] ... CHAINHASH_SIZE: 16384
[ 0.003333] memory used by lock dependency info: 5695 kB
[ 0.003333] per task-struct memory footprint: 1920 bytes
[ 0.003333] hpet clockevent registered
[ 0.003333] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.003333] Calibrating delay loop (skipped), value calculated using timer frequency.. 3991.20 BogoMIPS (lpj=6649923)
[ 0.003333] Security Framework initialized
[ 0.003333] Mount-cache hash table entries: 256
[ 0.003333] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.003333] CPU: L2 cache: 2048K
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 0
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] CPU0: Thermal monitoring enabled (TM2)
[ 0.003333] using mwait in idle threads.
[ 0.003333] Performance Counters: Core2 events, Intel PMU driver.
[ 0.003333] ... version: 2
[ 0.003333] ... bit width: 40
[ 0.003333] ... generic counters: 2
[ 0.003333] ... value mask: 000000ffffffffff
[ 0.003333] ... max period: 000000007fffffff
[ 0.003333] ... fixed-purpose counters: 3
[ 0.003333] ... counter mask: 0000000700000003
[ 0.003333] ACPI: Core revision 20090521
[ 0.013479] Setting APIC routing to flat
[ 0.013920] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.047241] CPU0: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.049999] lockdep: fixing up alternatives.
[ 0.049999] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.003333] Initializing CPU#1
[ 0.003333] Calibrating delay using timer specific routine.. 3991.23 BogoMIPS (lpj=6649977)
[ 0.003333] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.003333] CPU: L2 cache: 2048K
[ 0.003333] CPU: Physical Processor ID: 0
[ 0.003333] CPU: Processor Core ID: 1
[ 0.003333] mce: CPU supports 6 MCE banks
[ 0.003333] CPU1: Thermal monitoring enabled (TM2)
[ 0.003333] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.141318] CPU1: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz stepping 0d
[ 0.141580] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.143400] Brought up 2 CPUs
[ 0.143424] Total of 2 processors activated (7983.43 BogoMIPS).
[ 0.143543] CPU0 attaching sched-domain:
[ 0.143546] domain 0: span 0-1 level MC
[ 0.143549] groups: 0 1
[ 0.143568] CPU1 attaching sched-domain:
[ 0.143571] domain 0: span 0-1 level MC
[ 0.143574] groups: 1 0
[ 0.146708] NET: Registered protocol family 16
[ 0.146830] ACPI: bus type pci registered
[ 0.146830] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.146830] PCI: MCFG area at f8000000 reserved in E820
[ 0.147855] PCI: Using MMCONFIG at f8000000 - fbffffff
[ 0.147880] PCI: Using configuration type 1 for base access
[ 0.156783] bio: create slab <bio-0> at 0
[ 0.161517] ACPI: EC: Look up EC in DSDT
[ 0.179971] ACPI: SSDT 000000007f67e080 00043 (v01 LMPWR DELLLOM 00001001 INTL 20050624)
[ 0.198639] ACPI: Interpreter enabled
[ 0.198664] ACPI: (supports S0 S3 S4 S5)
[ 0.201295] ACPI: Using IOAPIC for interrupt routing
[ 0.253747] ACPI: No dock devices found.
[ 0.276582] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.276851] pci 0000:00:02.0: reg 10 64bit mmio: [0xf6e00000-0xf6efffff]
[ 0.276863] pci 0000:00:02.0: reg 18 64bit mmio: [0xe0000000-0xefffffff]
[ 0.276870] pci 0000:00:02.0: reg 20 io port: [0xeff8-0xefff]
[ 0.276938] pci 0000:00:02.1: reg 10 64bit mmio: [0xf6f00000-0xf6ffffff]
[ 0.277123] pci 0000:00:1a.0: reg 20 io port: [0x6f20-0x6f3f]
[ 0.277212] pci 0000:00:1a.1: reg 20 io port: [0x6f00-0x6f1f]
[ 0.277315] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfed1c400-0xfed1c7ff]
[ 0.277402] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.277434] pci 0000:00:1a.7: PME# disabled
[ 0.277530] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf6dfc000-0xf6dfffff]
[ 0.277614] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.277644] pci 0000:00:1b.0: PME# disabled
[ 0.277782] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.277812] pci 0000:00:1c.0: PME# disabled
[ 0.277953] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.277984] pci 0000:00:1c.1: PME# disabled
[ 0.278128] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.278158] pci 0000:00:1c.3: PME# disabled
[ 0.278306] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.278336] pci 0000:00:1c.5: PME# disabled
[ 0.278444] pci 0000:00:1d.0: reg 20 io port: [0x6f80-0x6f9f]
[ 0.278533] pci 0000:00:1d.1: reg 20 io port: [0x6f60-0x6f7f]
[ 0.278623] pci 0000:00:1d.2: reg 20 io port: [0x6f40-0x6f5f]
[ 0.278723] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfed1c000-0xfed1c3ff]
[ 0.278809] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.278840] pci 0000:00:1d.7: PME# disabled
[ 0.279087] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.279128] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.279159] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0900 (mask 007f)
[ 0.279201] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0c80 (mask 003f)
[ 0.279309] pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
[ 0.279320] pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
[ 0.279330] pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
[ 0.279340] pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
[ 0.279351] pci 0000:00:1f.1: reg 20 io port: [0x6fa0-0x6faf]
[ 0.279452] pci 0000:00:1f.2: reg 10 io port: [0x6eb0-0x6eb7]
[ 0.279463] pci 0000:00:1f.2: reg 14 io port: [0x6eb8-0x6ebb]
[ 0.279473] pci 0000:00:1f.2: reg 18 io port: [0x6ec0-0x6ec7]
[ 0.279484] pci 0000:00:1f.2: reg 1c io port: [0x6ec8-0x6ecb]
[ 0.279494] pci 0000:00:1f.2: reg 20 io port: [0x6ee0-0x6eff]
[ 0.279504] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf6dfb800-0xf6dfbfff]
[ 0.279563] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.279592] pci 0000:00:1f.2: PME# disabled
[ 0.279660] pci 0000:00:1f.3: reg 10 32bit mmio: [0xf6dfb700-0xf6dfb7ff]
[ 0.279693] pci 0000:00:1f.3: reg 20 io port: [0x10c0-0x10df]
[ 0.280146] pci 0000:0c:00.0: reg 10 32bit mmio: [0xf6cff000-0xf6cfffff]
[ 0.280415] pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
[ 0.280453] pci 0000:0c:00.0: PME# disabled
[ 0.280631] pci 0000:0c:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.280952] pci 0000:00:1c.1: bridge 32bit mmio: [0xf6c00000-0xf6cfffff]
[ 0.281071] pci 0000:00:1c.3: bridge io port: [0xd000-0xdfff]
[ 0.281078] pci 0000:00:1c.3: bridge 32bit mmio: [0xf6a00000-0xf6bfffff]
[ 0.281088] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
[ 0.281304] pci 0000:09:00.0: reg 10 64bit mmio: [0xf69f0000-0xf69fffff]
[ 0.281570] pci 0000:09:00.0: PME# supported from D3hot D3cold
[ 0.281606] pci 0000:09:00.0: PME# disabled
[ 0.282225] pci 0000:00:1c.5: bridge 32bit mmio: [0xf6900000-0xf69fffff]
[ 0.282299] pci 0000:03:01.0: reg 10 32bit mmio: [0xf68ff800-0xf68fffff]
[ 0.282380] pci 0000:03:01.0: supports D1 D2
[ 0.282382] pci 0000:03:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.282413] pci 0000:03:01.0: PME# disabled
[ 0.282493] pci 0000:03:01.1: reg 10 32bit mmio: [0xf68ff500-0xf68ff5ff]
[ 0.282575] pci 0000:03:01.1: supports D1 D2
[ 0.282578] pci 0000:03:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.283354] pci 0000:03:01.1: PME# disabled
[ 0.283435] pci 0000:03:01.2: reg 10 32bit mmio: [0xf68ff600-0xf68ff6ff]
[ 0.283516] pci 0000:03:01.2: supports D1 D2
[ 0.283518] pci 0000:03:01.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.283550] pci 0000:03:01.2: PME# disabled
[ 0.283630] pci 0000:03:01.3: reg 10 32bit mmio: [0xf68ff700-0xf68ff7ff]
[ 0.283710] pci 0000:03:01.3: supports D1 D2
[ 0.283712] pci 0000:03:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.283744] pci 0000:03:01.3: PME# disabled
[ 0.283887] pci 0000:00:1e.0: transparent bridge
[ 0.283919] pci 0000:00:1e.0: bridge 32bit mmio: [0xf6800000-0xf68fffff]
[ 0.283971] pci_bus 0000:00: on NUMA node 0
[ 0.283977] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.284550] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.284822] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.286709] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.286843] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.286978] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.310257] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.310507] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.310752] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *4
[ 0.311003] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.311262] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.311579] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.311897] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
[ 0.312191] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.313453] SCSI subsystem initialized
[ 0.313453] libata version 3.00 loaded.
[ 0.313453] usbcore: registered new interface driver usbfs
[ 0.313453] usbcore: registered new interface driver hub
[ 0.313453] usbcore: registered new device driver usb
[ 0.313453] PCI: Using ACPI for IRQ routing
[ 0.373379] cfg80211: Using static regulatory domain info
[ 0.373388] cfg80211: Regulatory domain: US
[ 0.373412] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 0.373450] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 0.373478] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.373506] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.373534] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.373561] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 0.373589] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 0.373698] cfg80211: Calling CRDA for country: US
[ 0.373805] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.373805] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.396684] pnp: PnP ACPI init
[ 0.396745] ACPI: bus type pnp registered
[ 0.420954] pnp 00:09: io resource (0x1000-0x1005) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.420997] pnp 00:09: io resource (0x1008-0x100f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.421264] pnp 00:0a: io resource (0x1006-0x1007) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.421306] pnp 00:0a: io resource (0x100a-0x1059) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.421348] pnp 00:0a: io resource (0x1060-0x107f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.421389] pnp 00:0a: io resource (0x1010-0x102f) overlaps 0000:00:1f.0 BAR 7 (0x1000-0x107f), disabling
[ 0.447605] pnp: PnP ACPI: found 12 devices
[ 0.447631] ACPI: ACPI bus type pnp unregistered
[ 0.447674] system 00:05: ioport range 0xc80-0xcff could not be reserved
[ 0.447713] system 00:08: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.447750] system 00:09: ioport range 0x900-0x97f has been reserved
[ 0.447778] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 0.447815] system 00:0a: ioport range 0xf400-0xf4fe has been reserved
[ 0.447843] system 00:0a: ioport range 0x1080-0x10bf has been reserved
[ 0.447872] system 00:0a: ioport range 0x10c0-0x10df has been reserved
[ 0.447900] system 00:0a: ioport range 0x809-0x809 has been reserved
[ 0.447936] system 00:0b: iomem range 0x0-0x9efff could not be reserved
[ 0.447965] system 00:0b: iomem range 0x9f000-0x9ffff could not be reserved
[ 0.447994] system 00:0b: iomem range 0xc0000-0xcffff has been reserved
[ 0.448022] system 00:0b: iomem range 0xe0000-0xfffff has been reserved
[ 0.448050] system 00:0b: iomem range 0x100000-0x7f66d7ff could not be reserved
[ 0.448089] system 00:0b: iomem range 0x7f66d800-0x7f6fffff has been reserved
[ 0.448118] system 00:0b: iomem range 0x7f700000-0x7f7fffff has been reserved
[ 0.448147] system 00:0b: iomem range 0x7f700000-0x7fefffff could not be reserved
[ 0.448186] system 00:0b: iomem range 0xffe00000-0xffffffff has been reserved
[ 0.448215] system 00:0b: iomem range 0xffa00000-0xffbfffff has been reserved
[ 0.448244] system 00:0b: iomem range 0xfec00000-0xfec0ffff has been reserved
[ 0.448273] system 00:0b: iomem range 0xfee00000-0xfee0ffff has been reserved
[ 0.448302] system 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.448331] system 00:0b: iomem range 0xfeda0000-0xfeda3fff has been reserved
[ 0.448360] system 00:0b: iomem range 0xfeda4000-0xfeda4fff has been reserved
[ 0.448389] system 00:0b: iomem range 0xfeda5000-0xfeda5fff has been reserved
[ 0.448418] system 00:0b: iomem range 0xfeda6000-0xfeda6fff has been reserved
[ 0.448447] system 00:0b: iomem range 0xfed18000-0xfed1bfff has been reserved
[ 0.448476] system 00:0b: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.454149] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:0b
[ 0.454176] pci 0000:00:1c.0: IO window: disabled
[ 0.454207] pci 0000:00:1c.0: MEM window: disabled
[ 0.454235] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.454265] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0c
[ 0.454291] pci 0000:00:1c.1: IO window: disabled
[ 0.454321] pci 0000:00:1c.1: MEM window: 0xf6c00000-0xf6cfffff
[ 0.454351] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.454381] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0d
[ 0.454409] pci 0000:00:1c.3: IO window: 0xd000-0xdfff
[ 0.454440] pci 0000:00:1c.3: MEM window: 0xf6a00000-0xf6bfffff
[ 0.454471] pci 0000:00:1c.3: PREFETCH window: 0x000000f0000000-0x000000f01fffff
[ 0.454516] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:09
[ 0.454542] pci 0000:00:1c.5: IO window: disabled
[ 0.454573] pci 0000:00:1c.5: MEM window: 0xf6900000-0xf69fffff
[ 0.454603] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.454633] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[ 0.454658] pci 0000:00:1e.0: IO window: disabled
[ 0.454689] pci 0000:00:1e.0: MEM window: 0xf6800000-0xf68fffff
[ 0.454719] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.454765] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.454797] pci 0000:00:1c.0: setting latency timer to 64
[ 0.454811] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.454843] pci 0000:00:1c.1: setting latency timer to 64
[ 0.454858] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.454889] pci 0000:00:1c.3: setting latency timer to 64
[ 0.454901] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.454932] pci 0000:00:1c.5: setting latency timer to 64
[ 0.454943] pci 0000:00:1e.0: setting latency timer to 64
[ 0.454949] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.454953] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.454956] pci_bus 0000:0c: resource 1 mem: [0xf6c00000-0xf6cfffff]
[ 0.454959] pci_bus 0000:0d: resource 0 io: [0xd000-0xdfff]
[ 0.454961] pci_bus 0000:0d: resource 1 mem: [0xf6a00000-0xf6bfffff]
[ 0.454964] pci_bus 0000:0d: resource 2 pref mem [0xf0000000-0xf01fffff]
[ 0.454967] pci_bus 0000:09: resource 1 mem: [0xf6900000-0xf69fffff]
[ 0.454970] pci_bus 0000:03: resource 1 mem: [0xf6800000-0xf68fffff]
[ 0.454973] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.454976] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.455051] NET: Registered protocol family 2
[ 0.455313] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.456226] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.458260] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
[ 0.464779] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.464861] TCP reno registered
[ 0.465121] NET: Registered protocol family 1
[ 0.465470] Simple Boot Flag at 0x79 set to 0x1
[ 0.468571] cpu0(2) debug files 152
[ 0.471472] cpu1(2) debug files 152
[ 0.479951] msgmni has been set to 3983
[ 0.480780] alg: No test for stdrng (krng)
[ 0.480831] io scheduler noop registered
[ 0.480871] io scheduler cfq registered (default)
[ 0.480913] pci 0000:00:02.0: Boot video device
[ 0.480927] pci 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0080
[ 0.480929] pci 0000:00:1a.0: Performing full reset
[ 0.480953] pci 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0080
[ 0.480955] pci 0000:00:1a.1: Performing full reset
[ 0.481022] pci 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0080
[ 0.481024] pci 0000:00:1d.0: Performing full reset
[ 0.481047] pci 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0080
[ 0.481050] pci 0000:00:1d.1: Performing full reset
[ 0.481073] pci 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0080
[ 0.481075] pci 0000:00:1d.2: Performing full reset
[ 0.481486] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.481502] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.481975] pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.481989] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 0.482381] pcieport-driver 0000:00:1c.3: irq 26 for MSI/MSI-X
[ 0.482396] pcieport-driver 0000:00:1c.3: setting latency timer to 64
[ 0.482784] pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X
[ 0.482799] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.483221] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.483700] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.483727] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.483910] acpiphp_glue: can't get bus number, assuming 0
[ 0.484331] decode_hpp: Could not get hotplug parameters. Use defaults
[ 0.484690] acpiphp: Slot [1] registered
[ 0.484908] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 0.485417] ACPI: AC Adapter [AC] (on-line)
[ 0.485807] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[ 0.486462] ACPI: Lid Switch [LID]
[ 0.486636] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.486687] ACPI: Power Button [PBTN]
[ 0.486862] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 0.486902] ACPI: Sleep Button [SBTN]
[ 0.487710] ACPI: SSDT 000000007f66e4ee 00286 (v01 PmRef Cpu0Ist 00003000 INTL 20050624)
[ 0.488691] ACPI: SSDT 000000007f66de84 005E5 (v01 PmRef Cpu0Cst 00003001 INTL 20050624)
[ 0.489545] Monitor-Mwait will be used to enter C-1 state
[ 0.489584] Monitor-Mwait will be used to enter C-2 state
[ 0.489620] Monitor-Mwait will be used to enter C-3 state
[ 0.489633] Marking TSC unstable due to TSC halts in idle
[ 0.489793] Switched to high resolution mode on CPU 0
[ 0.490147] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 0.490398] processor LNXCPU:00: registered as cooling_device0
[ 0.490429] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.490998] ACPI: SSDT 000000007f66e774 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20050624)
[ 0.491666] Switched to high resolution mode on CPU 1
[ 0.491818] ACPI: SSDT 000000007f66e469 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
[ 0.492924] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 0.493069] processor LNXCPU:01: registered as cooling_device1
[ 0.493100] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.502890] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.502935] ACPI: Thermal Zone [THM] (61 C)
[ 0.503257] ACPI: Battery Slot [BAT0] (battery absent)
[ 0.509709] Linux agpgart interface v0.103
[ 0.510094] ahci 0000:00:1f.2: version 3.0
[ 0.510112] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.510197] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
[ 0.510289] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
[ 0.510330] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems
[ 0.510372] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.517632] scsi0 : ahci
[ 0.518088] scsi1 : ahci
[ 0.518314] scsi2 : ahci
[ 0.518805] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 28
[ 0.518844] ata2: DUMMY
[ 0.518867] ata3: SATA max UDMA/133 abar m2048@0xf6dfb800 port 0xf6dfba00 irq 28
[ 0.519061] ata_piix 0000:00:1f.1: version 2.13
[ 0.519072] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.521695] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.521795] scsi3 : ata_piix
[ 0.522043] scsi4 : ata_piix
[ 0.523034] ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x6fa0 irq 14
[ 0.523063] ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x6fa8 irq 15
[ 0.523389] tg3.c:v3.99 (April 20, 2009)
[ 0.523438] tg3 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.523478] tg3 0000:09:00.0: setting latency timer to 64
[ 0.523801] ata5: port disabled. ignoring.
[ 0.530095] tg3 0000:09:00.0: PME# disabled
[ 0.680432] ata4.00: ATAPI: HL-DT-ST DVDRW GSA-S10N, A100, max UDMA/33
[ 0.693646] ata4.00: configured for UDMA/33
[ 0.781835] eth0: Tigon3 [partno(BCM95906) rev c002] (PCI Express) MAC address 00:1d:09:35:87:70
[ 0.781875] eth0: attached PHY is 5906 (10/100Base-TX Ethernet) (WireSpeed[0])
[ 0.781913] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0]
[ 0.781940] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 0.782043] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 0.782082] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 0.782206] iwl3945 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.782246] iwl3945 0000:0c:00.0: setting latency timer to 64
[ 0.840932] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.853539] iwl3945 0000:0c:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 0.853578] iwl3945 0000:0c:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 0.853759] iwl3945 0000:0c:00.0: irq 29 for MSI/MSI-X
[ 0.855734] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 0.856764] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.856793] ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
[ 0.856836] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 0.856878] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.856882] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.857030] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.857075] ehci_hcd 0000:00:1a.7: reset hcs_params 0x102204 dbg=1 cc=2 pcc=2 ordered !ppc ports=4
[ 0.857081] ehci_hcd 0000:00:1a.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[ 0.857121] ehci_hcd 0000:00:1a.7: reset command 000002 (park)=0 ithresh=0 period=1024 Reset HALT
[ 0.861008] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.861039] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.861041] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[ 0.861069] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
[ 0.861098] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 0.864995] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 0.876696] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.876853] usb usb1: default language 0x0409
[ 0.876871] usb usb1: udev 1, busnum 1, minor = 0
[ 0.876874] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.876902] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.876939] usb usb1: Product: EHCI Host Controller
[ 0.876964] usb usb1: Manufacturer: Linux 2.6.31-rc2-t ehci_hcd
[ 0.876990] usb usb1: SerialNumber: 0000:00:1a.7
[ 0.877292] usb usb1: uevent
[ 0.877460] usb usb1: usb_probe_device
[ 0.877463] usb usb1: configuration #1 chosen from 1 choice
[ 0.877616] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 0.877655] usb 1-0:1.0: uevent
[ 0.877765] hub 1-0:1.0: usb_probe_interface
[ 0.877768] hub 1-0:1.0: usb_probe_interface - got id
[ 0.877771] hub 1-0:1.0: USB hub found
[ 0.877824] hub 1-0:1.0: 4 ports detected
[ 0.877848] hub 1-0:1.0: standalone hub
[ 0.877849] hub 1-0:1.0: no power switching (usb 1.0)
[ 0.877852] hub 1-0:1.0: individual port over-current protection
[ 0.877854] hub 1-0:1.0: power on to power good time: 20ms
[ 0.877979] hub 1-0:1.0: local power source is good
[ 0.877982] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 0.878663] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.878703] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.878707] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.878742] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.878786] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[ 0.878791] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[ 0.878818] ehci_hcd 0000:00:1d.7: reset command 000002 (park)=0 ithresh=0 period=1024 Reset HALT
[ 0.882708] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.882738] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.882741] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 0.882767] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
[ 0.882796] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[ 0.886694] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[ 0.896683] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.896796] usb usb2: default language 0x0409
[ 0.896813] usb usb2: udev 1, busnum 2, minor = 128
[ 0.896815] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.896843] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.896880] usb usb2: Product: EHCI Host Controller
[ 0.896905] usb usb2: Manufacturer: Linux 2.6.31-rc2-t ehci_hcd
[ 0.896931] usb usb2: SerialNumber: 0000:00:1d.7
[ 0.897043] usb usb2: uevent
[ 0.897108] usb usb2: usb_probe_device
[ 0.897111] usb usb2: configuration #1 chosen from 1 choice
[ 0.897147] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 0.897184] usb 2-0:1.0: uevent
[ 0.897248] hub 2-0:1.0: usb_probe_interface
[ 0.897251] hub 2-0:1.0: usb_probe_interface - got id
[ 0.897254] hub 2-0:1.0: USB hub found
[ 0.897287] hub 2-0:1.0: 6 ports detected
[ 0.897310] hub 2-0:1.0: standalone hub
[ 0.897312] hub 2-0:1.0: no power switching (usb 1.0)
[ 0.897314] hub 2-0:1.0: individual port over-current protection
[ 0.897317] hub 2-0:1.0: power on to power good time: 20ms
[ 0.897328] hub 2-0:1.0: local power source is good
[ 0.897330] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 0.897603] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.897784] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.897820] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.897824] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.897859] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.897904] uhci_hcd 0000:00:1a.0: detected 2 ports
[ 0.897932] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.897935] uhci_hcd 0000:00:1a.0: Performing full reset
[ 0.897952] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[ 0.897964] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
[ 0.898063] usb usb3: default language 0x0409
[ 0.898079] usb usb3: udev 1, busnum 3, minor = 256
[ 0.898082] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.898110] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.898147] usb usb3: Product: UHCI Host Controller
[ 0.898172] usb usb3: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 0.898198] usb usb3: SerialNumber: 0000:00:1a.0
[ 0.898348] usb usb3: uevent
[ 0.898415] usb usb3: usb_probe_device
[ 0.898418] usb usb3: configuration #1 chosen from 1 choice
[ 0.898453] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 0.898490] usb 3-0:1.0: uevent
[ 0.898554] hub 3-0:1.0: usb_probe_interface
[ 0.898556] hub 3-0:1.0: usb_probe_interface - got id
[ 0.898559] hub 3-0:1.0: USB hub found
[ 0.898631] hub 3-0:1.0: 2 ports detected
[ 0.898654] hub 3-0:1.0: standalone hub
[ 0.898656] hub 3-0:1.0: no power switching (usb 1.0)
[ 0.898658] hub 3-0:1.0: individual port over-current protection
[ 0.898661] hub 3-0:1.0: power on to power good time: 2ms
[ 0.898693] hub 3-0:1.0: local power source is good
[ 0.898696] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 0.898892] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.898927] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.898931] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.898966] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.899009] uhci_hcd 0000:00:1a.1: detected 2 ports
[ 0.899038] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.899040] uhci_hcd 0000:00:1a.1: Performing full reset
[ 0.899057] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[ 0.899082] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
[ 0.899182] usb usb4: default language 0x0409
[ 0.899199] usb usb4: udev 1, busnum 4, minor = 384
[ 0.899201] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.899229] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.899266] usb usb4: Product: UHCI Host Controller
[ 0.899291] usb usb4: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 0.899317] usb usb4: SerialNumber: 0000:00:1a.1
[ 0.899425] usb usb4: uevent
[ 0.899490] usb usb4: usb_probe_device
[ 0.899492] usb usb4: configuration #1 chosen from 1 choice
[ 0.899527] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 0.899568] usb 4-0:1.0: uevent
[ 0.899632] hub 4-0:1.0: usb_probe_interface
[ 0.899634] hub 4-0:1.0: usb_probe_interface - got id
[ 0.899637] hub 4-0:1.0: USB hub found
[ 0.899670] hub 4-0:1.0: 2 ports detected
[ 0.899693] hub 4-0:1.0: standalone hub
[ 0.899695] hub 4-0:1.0: no power switching (usb 1.0)
[ 0.899697] hub 4-0:1.0: individual port over-current protection
[ 0.899700] hub 4-0:1.0: power on to power good time: 2ms
[ 0.899710] hub 4-0:1.0: local power source is good
[ 0.899713] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 0.899905] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.899940] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.899944] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.899979] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 0.900035] uhci_hcd 0000:00:1d.0: detected 2 ports
[ 0.900063] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.900066] uhci_hcd 0000:00:1d.0: Performing full reset
[ 0.900083] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[ 0.900095] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
[ 0.900180] usb usb5: default language 0x0409
[ 0.900197] usb usb5: udev 1, busnum 5, minor = 512
[ 0.900200] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.900228] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.900265] usb usb5: Product: UHCI Host Controller
[ 0.900290] usb usb5: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 0.900316] usb usb5: SerialNumber: 0000:00:1d.0
[ 0.900426] usb usb5: uevent
[ 0.900490] usb usb5: usb_probe_device
[ 0.900493] usb usb5: configuration #1 chosen from 1 choice
[ 0.900528] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[ 0.900565] usb 5-0:1.0: uevent
[ 0.900631] hub 5-0:1.0: usb_probe_interface
[ 0.900633] hub 5-0:1.0: usb_probe_interface - got id
[ 0.900636] hub 5-0:1.0: USB hub found
[ 0.900669] hub 5-0:1.0: 2 ports detected
[ 0.900692] hub 5-0:1.0: standalone hub
[ 0.900694] hub 5-0:1.0: no power switching (usb 1.0)
[ 0.900696] hub 5-0:1.0: individual port over-current protection
[ 0.900699] hub 5-0:1.0: power on to power good time: 2ms
[ 0.900710] hub 5-0:1.0: local power source is good
[ 0.900712] hub 5-0:1.0: trying to enable port power on non-switchable hub
[ 0.900906] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.900941] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.900945] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.900980] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 0.901023] uhci_hcd 0000:00:1d.1: detected 2 ports
[ 0.901051] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.901054] uhci_hcd 0000:00:1d.1: Performing full reset
[ 0.901070] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[ 0.901081] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
[ 0.901169] usb usb6: default language 0x0409
[ 0.901186] usb usb6: udev 1, busnum 6, minor = 640
[ 0.901189] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.901216] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.901253] usb usb6: Product: UHCI Host Controller
[ 0.901278] usb usb6: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 0.901304] usb usb6: SerialNumber: 0000:00:1d.1
[ 0.901415] usb usb6: uevent
[ 0.901486] usb usb6: usb_probe_device
[ 0.901489] usb usb6: configuration #1 chosen from 1 choice
[ 0.901524] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[ 0.901562] usb 6-0:1.0: uevent
[ 0.901631] hub 6-0:1.0: usb_probe_interface
[ 0.901634] hub 6-0:1.0: usb_probe_interface - got id
[ 0.901637] hub 6-0:1.0: USB hub found
[ 0.901670] hub 6-0:1.0: 2 ports detected
[ 0.901693] hub 6-0:1.0: standalone hub
[ 0.901695] hub 6-0:1.0: no power switching (usb 1.0)
[ 0.901697] hub 6-0:1.0: individual port over-current protection
[ 0.901699] hub 6-0:1.0: power on to power good time: 2ms
[ 0.901710] hub 6-0:1.0: local power source is good
[ 0.901713] hub 6-0:1.0: trying to enable port power on non-switchable hub
[ 0.901910] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 0.901944] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.901949] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.901983] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 0.902027] uhci_hcd 0000:00:1d.2: detected 2 ports
[ 0.902056] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[ 0.902058] uhci_hcd 0000:00:1d.2: Performing full reset
[ 0.902076] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[ 0.902087] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
[ 0.902171] usb usb7: default language 0x0409
[ 0.902187] usb usb7: udev 1, busnum 7, minor = 768
[ 0.902190] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.902218] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.902255] usb usb7: Product: UHCI Host Controller
[ 0.902279] usb usb7: Manufacturer: Linux 2.6.31-rc2-t uhci_hcd
[ 0.902306] usb usb7: SerialNumber: 0000:00:1d.2
[ 0.902416] usb usb7: uevent
[ 0.902487] usb usb7: usb_probe_device
[ 0.902490] usb usb7: configuration #1 chosen from 1 choice
[ 0.902525] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[ 0.902563] usb 7-0:1.0: uevent
[ 0.902631] hub 7-0:1.0: usb_probe_interface
[ 0.902634] hub 7-0:1.0: usb_probe_interface - got id
[ 0.902637] hub 7-0:1.0: USB hub found
[ 0.902670] hub 7-0:1.0: 2 ports detected
[ 0.902693] hub 7-0:1.0: standalone hub
[ 0.902695] hub 7-0:1.0: no power switching (usb 1.0)
[ 0.902697] hub 7-0:1.0: individual port over-current protection
[ 0.902700] hub 7-0:1.0: power on to power good time: 2ms
[ 0.902711] hub 7-0:1.0: local power source is good
[ 0.902713] hub 7-0:1.0: trying to enable port power on non-switchable hub
[ 0.902981] Initializing USB Mass Storage driver...
[ 0.903108] usbcore: registered new interface driver usb-storage
[ 0.903137] USB Mass Storage support registered.
[ 0.903436] usbcore: registered new interface driver libusual
[ 0.903536] usbcore: registered new interface driver ums-alauda
[ 0.903634] usbcore: registered new interface driver ums-cypress
[ 0.903738] usbcore: registered new interface driver ums-datafab
[ 0.903839] usbcore: registered new interface driver ums-freecom
[ 0.903938] usbcore: registered new interface driver ums-isd200
[ 0.904035] usbcore: registered new interface driver ums-jumpshot
[ 0.904135] usbcore: registered new interface driver ums-karma
[ 0.904234] usbcore: registered new interface driver ums-sddr09
[ 0.904332] usbcore: registered new interface driver ums-sddr55
[ 0.904429] usbcore: registered new interface driver ums-usbat
[ 0.904624] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.904681] Platform driver 'i8042' needs updating - please use dev_pm_ops
[ 0.908076] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.908130] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.908310] mice: PS/2 mouse device common for all mice
[ 0.909090] rtc_cmos 00:03: RTC can wake from S4
[ 0.909326] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.909390] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.909486] i2c /dev entries driver
[ 0.909672] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.910847] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 0.911088] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 0.911273] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 0.911302] iTCO_vendor_support: vendor-support=0
[ 0.911913] cpuidle: using governor ladder
[ 0.912473] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 0.913195] cpuidle: using governor menu
[ 0.913290] sdhci: Secure Digital Host Controller Interface driver
[ 0.913316] sdhci: Copyright(c) Pierre Ossman
[ 0.913421] sdhci-pci 0000:03:01.1: SDHCI controller found [1180:0822] (rev 22)
[ 0.913479] sdhci-pci 0000:03:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 0.918348] Registered led device: mmc0::
[ 0.919578] mmc0: SDHCI controller on PCI [0000:03:01.1] using DMA
[ 0.919799] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 0.919825] ricoh-mmc: Copyright(c) Philip Langdale
[ 0.920165] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 0.922586] usbcore: registered new interface driver hiddev
[ 0.922700] usbcore: registered new interface driver usbhid
[ 0.922728] usbhid: v2.6:USB HID core driver
[ 0.922916] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 0.923513] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.923593] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 0.977127] hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 0.993633] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
[ 0.993644] hub 2-0:1.0: port 6: status 0501 change 0001
[ 0.994723] mmc0: new high speed SD card at address 0002
[ 0.995211] mmcblk0: mmc0:0002 00000 1.88 GiB
[ 0.995490] mmcblk0: p1
[ 0.996797] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 0.996805] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 0.996843] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.000123] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 1.000126] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.093614] hub 2-0:1.0: state 7 ports 6 chg 0040 evt 0000
[ 1.093643] hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
[ 1.147221] ehci_hcd 0000:00:1d.7: port 6 high speed
[ 1.147226] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 1.200141] usb 2-6: new high speed USB device using ehci_hcd and address 2
[ 1.236746] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.253594] ehci_hcd 0000:00:1d.7: port 6 high speed
[ 1.253599] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
[ 1.260401] input: HDA Intel Line In at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
[ 1.260726] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 1.261020] input: HDA Intel Mic at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 1.261272] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 1.261525] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 1.261777] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 1.262027] input: HDA Intel Speaker at Ext Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 1.262279] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 1.263423] ALSA device list:
[ 1.263446] #0: HDA Intel at 0xf6dfc000 irq 21
[ 1.263509] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.264069] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.264107] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.264145] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 1.265322] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.265349] TCP cubic registered
[ 1.266050] NET: Registered protocol family 10
[ 1.267472] lo: Disabled Privacy Extensions
[ 1.270285] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.270312] NET: Registered protocol family 17
[ 1.270362] lib80211: common routines for IEEE802.11 drivers
[ 1.270398] lib80211_crypt: registered algorithm 'NULL'
[ 1.293068] ata1.00: ATA-8: WDC WD1200BEVS-75UST0, 01.01A01, max UDMA/133
[ 1.293123] ata1.00: 234441648 sectors, multi 8: LBA48 NCQ (depth 31/32)
[ 1.294562] ata1.00: configured for UDMA/133
[ 1.311356] scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVS-7 01.0 PQ: 0 ANSI: 5
[ 1.313704] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.313980] sd 0:0:0:0: [sda] Write Protect is off
[ 1.314025] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.314136] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.315118] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.315404] sda:
[ 1.318743] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRW GSA-S10N A100 PQ: 0 ANSI: 5
[ 1.322080] sda1 sda2 sda3 sda4 <
[ 1.328445] usb 2-6: skipped 2 descriptors after configuration
[ 1.328484] usb 2-6: skipped 7 descriptors after interface
[ 1.328493] usb 2-6: skipped 1 descriptor after endpoint
[ 1.328500] usb 2-6: skipped 15 descriptors after interface
[ 1.328796] usb 2-6: default language 0x0409
[ 1.329328] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda caddy
[ 1.329389] Uniform CD-ROM driver Revision: 3.20
[ 1.329912] usb 2-6: udev 2, busnum 2, minor = 129
[ 1.329919] usb 2-6: New USB device found, idVendor=05a9, idProduct=7670
[ 1.329968] usb 2-6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.330074] usb 2-6: Product: Laptop Integrated Webcam
[ 1.330117] usb 2-6: Manufacturer: OmniVision Technologies, Inc. -7670-07.09.28.1
[ 1.330445] usb 2-6: uevent
[ 1.330761] usb 2-6: usb_probe_device
[ 1.330770] usb 2-6: configuration #1 chosen from 1 choice
[ 1.331074] usb 2-6: adding 2-6:1.0 (config #1, interface 0)
[ 1.331769] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 1.331877] usb 2-6:1.0: uevent
[ 1.332237] usb 2-6: adding 2-6:1.1 (config #1, interface 1)
[ 1.332345] usb 2-6:1.1: uevent
[ 1.332527] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 1.333071] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[ 1.338065] sda5 sda6 >
[ 1.348877] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.500173] Clocksource tsc unstable (delta = -338684120 ns)
[ 1.570159] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps: 0xa04753/0x200000
[ 1.609003] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input12
[ 1.628365] rtc_cmos 00:03: setting system clock to 2009-08-02 18:02:18 UTC (1249236138)
[ 1.628434] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 1.628995] Initalizing network drop monitor service
[ 1.665362] EXT4-fs (sda2): barriers enabled
[ 1.690038] kjournald2 starting: pid 782, dev sda2:8, commit interval 5 seconds
[ 1.690248] EXT4-fs (sda2): delayed allocation enabled
[ 1.690694] EXT4-fs: mballoc enabled
[ 1.691008] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 1.691296] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 1.691495] Freeing unused kernel memory: 388k freed
[ 1.691752] Write protecting the kernel read-only data: 5696k
[ 2.096836] usb usb3: suspend_rh (auto-stop)
[ 2.096877] usb usb4: suspend_rh (auto-stop)
[ 2.096914] usb usb5: suspend_rh (auto-stop)
[ 2.096950] usb usb6: suspend_rh (auto-stop)
[ 2.096985] usb usb7: suspend_rh (auto-stop)
[ 3.338054] hub 1-0:1.0: hub_suspend
[ 3.338268] usb usb1: bus auto-suspend
[ 3.338275] ehci_hcd 0000:00:1a.7: suspend root hub
[ 3.338489] hub 3-0:1.0: hub_suspend
[ 3.338506] usb usb3: bus auto-suspend
[ 3.338535] usb usb3: suspend_rh
[ 3.338569] hub 4-0:1.0: hub_suspend
[ 3.338584] usb usb4: bus auto-suspend
[ 3.338590] usb usb4: suspend_rh
[ 3.338621] hub 5-0:1.0: hub_suspend
[ 3.338634] usb usb5: bus auto-suspend
[ 3.338640] usb usb5: suspend_rh
[ 3.338672] hub 6-0:1.0: hub_suspend
[ 3.338686] usb usb6: bus auto-suspend
[ 3.338692] usb usb6: suspend_rh
[ 3.346798] hub 7-0:1.0: hub_suspend
[ 3.346819] usb usb7: bus auto-suspend
[ 3.346827] usb usb7: suspend_rh
[ 3.896856] usb usb3: uevent
[ 3.896979] usb 3-0:1.0: uevent
[ 3.897330] usb usb4: uevent
[ 3.897437] usb 4-0:1.0: uevent
[ 3.898161] usb usb1: uevent
[ 3.899798] usb 1-0:1.0: uevent
[ 3.902388] usb usb3: uevent
[ 3.908472] usb usb1: uevent
[ 3.928335] usb usb4: uevent
[ 3.930260] usb usb5: uevent
[ 3.930352] usb 5-0:1.0: uevent
[ 3.930617] usb usb6: uevent
[ 3.930821] usb 6-0:1.0: uevent
[ 3.931959] usb usb7: uevent
[ 3.932050] usb 7-0:1.0: uevent
[ 3.932316] usb usb2: uevent
[ 3.932410] usb 2-0:1.0: uevent
[ 3.932502] usb 2-6: uevent
[ 3.932592] usb 2-6:1.0: uevent
[ 3.932685] usb 2-6:1.1: uevent
[ 3.947879] usb usb6: uevent
[ 3.951831] usb usb7: uevent
[ 3.955533] usb usb2: uevent
[ 3.960891] usb usb5: uevent
[ 3.963942] usb 2-6: uevent
[ 4.641380] ACPI: WMI: Mapper loaded
[ 4.656975] ohci1394 0000:03:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 4.679684] Linux video capture interface: v2.00
[ 4.715724] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[f68ff800-f68fffff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 4.740579] uvcvideo 2-6:1.0: usb_probe_interface
[ 4.740588] uvcvideo 2-6:1.0: usb_probe_interface - got id
[ 4.741269] uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:7670)
[ 4.741772] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
[ 4.743151] input: Laptop Integrated Webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6:1.0/input/input13
[ 4.743766] usbcore: registered new interface driver uvcvideo
[ 4.743817] USB Video Class driver (v0.1.0)
[ 4.751192] usb 2-6:1.0: uevent
[ 4.751393] usb 2-6: uevent
[ 4.758010] usb 2-6:1.0: uevent
[ 4.758213] usb 2-6: uevent
[ 5.249799] SysRq : Changing Loglevel
[ 5.249863] Loglevel set to 9
[ 5.376798] Adding 4096564k swap on /dev/sda3. Priority:-1 extents:1 across:4096564k
[ 5.989383] ieee1394: Host added: ID:BUS[0-00:1023] GUID[354fc000321a4870]
[ 16.916788] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 16.916858] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 16.916926] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 17.036895] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 17.090356] ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
[ 17.090405] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
[ 17.090465] hub 2-0:1.0: port 1 not reset yet, waiting 50ms
[ 17.090910] usb usb5: usb resume
[ 17.090949] usb usb5: wakeup_rh
[ 17.126948] hub 5-0:1.0: hub_resume
[ 17.127052] uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
[ 17.127102] hub 5-0:1.0: port 1: status 0101 change 0001
[ 17.143559] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC
[ 17.143711] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 17.143768] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 17.230423] hub 5-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 17.230502] uhci_hcd 0000:00:1d.0: port 1 portsc 0082,00
[ 17.230568] hub 5-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 17.350200] hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 18.015845] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 18.015914] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 18.015982] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 18.133539] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 18.187103] ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
[ 18.187149] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
[ 18.187222] hub 2-0:1.0: port 1 not reset yet, waiting 50ms
[ 18.240244] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
[ 18.240388] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 18.346992] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0002
[ 18.347078] uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
[ 18.347147] hub 5-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 18.466900] hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 18.573566] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 18.701089] usb 5-1: ep0 maxpacket = 16
[ 18.717676] usb 5-1: uhci_result_common: failed with status 440000
[ 18.720710] usb 5-1: uhci_result_common: failed with status 440000
[ 18.724709] usb 5-1: uhci_result_common: failed with status 440000
[ 18.724815] usb 5-1: unable to read config index 0 descriptor/all
[ 18.724863] usb 5-1: can't read configurations, error -71
[ 18.780302] hub 5-0:1.0: unable to enumerate USB device on port 1
[ 18.780372] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0002
[ 18.780445] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 18.780508] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC
[ 18.780589] hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 18.900132] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 19.846843] usb usb5: suspend_rh (auto-stop)
[ 21.346837] hub 5-0:1.0: hub_suspend
[ 21.346903] usb usb5: bus auto-suspend
[ 21.346946] usb usb5: suspend_rh
[ 24.996473] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 24.996553] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 24.996643] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 25.113540] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 25.167106] ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
[ 25.167162] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
[ 25.167274] hub 2-0:1.0: port 1 not reset yet, waiting 50ms
[ 25.167314] usb usb5: usb resume
[ 25.167322] usb usb5: wakeup_rh
[ 25.203589] hub 5-0:1.0: hub_resume
[ 25.203657] uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
[ 25.203712] hub 5-0:1.0: port 1: status 0101 change 0001
[ 25.220906] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC
[ 25.221026] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 25.221093] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 25.306905] hub 5-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 25.306997] uhci_hcd 0000:00:1d.0: port 1 portsc 0082,00
[ 25.307080] hub 5-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 25.427785] hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 26.095635] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 26.095717] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 26.095806] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 26.213560] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 26.267105] ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
[ 26.267166] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
[ 26.267240] hub 2-0:1.0: port 1 not reset yet, waiting 50ms
[ 26.320238] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
[ 26.320381] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 26.346928] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0002
[ 26.347001] uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
[ 26.347068] hub 5-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 26.466907] hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 26.573572] usb 5-1: new full speed USB device using uhci_hcd and address 4
[ 26.700214] usb 5-1: ep0 maxpacket = 16
[ 26.717385] usb 5-1: skipped 4 descriptors after interface
[ 26.717437] usb 5-1: skipped 1 descriptor after interface
[ 26.728379] usb 5-1: skipped 4 descriptors after interface
[ 26.731356] usb 5-1: default language 0x0409
[ 26.750370] usb 5-1: udev 4, busnum 5, minor = 515
[ 26.750416] usb 5-1: New USB device found, idVendor=1457, idProduct=5119
[ 26.750463] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 26.750511] usb 5-1: Product: Neo1973 Bootloader U-Boot 1.3.2-rc2
[ 26.750555] usb 5-1: Manufacturer: OpenMoko, Inc
[ 26.750595] usb 5-1: SerialNumber: 0000000
[ 26.750946] usb 5-1: uevent
[ 26.751811] usb 5-1: usb_probe_device
[ 26.751855] usb 5-1: configuration #1 chosen from 2 choices
[ 26.757376] usb 5-1: adding 5-1:1.0 (config #1, interface 0)
[ 26.759286] usb 5-1:1.0: uevent
[ 26.760346] usb 5-1: adding 5-1:1.1 (config #1, interface 1)
[ 26.762411] usb 5-1:1.1: uevent
[ 26.763444] usb 5-1: adding 5-1:1.2 (config #1, interface 2)
[ 26.765283] usb 5-1:1.2: uevent
[ 26.766104] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0002
[ 26.773847] usb 5-1: uevent
[ 26.876580] cdc_acm 5-1:1.0: usb_probe_interface
[ 26.876631] cdc_acm 5-1:1.0: usb_probe_interface - got id
[ 26.876703] cdc_acm 5-1:1.0: This device cannot do calls on its own. It is not a modem.
[ 26.876850] cdc_acm 5-1:1.0: ttyACM0: USB ACM device
[ 26.879782] usbcore: registered new interface driver cdc_acm
[ 26.879836] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 26.897431] usb 5-1:1.0: uevent
[ 26.898016] usb 5-1: uevent
[ 26.941203] uhci_hcd 0000:00:1d.0: reserve dev 4 ep81-INT, period 128, phase 0, 23 us
[ 37.133312] uhci_hcd 0000:00:1d.0: release dev 4 ep81-INT, period 128, phase 0, 23 us
[ 38.024110] uhci_hcd 0000:00:1d.0: reserve dev 4 ep81-INT, period 128, phase 0, 23 us
[ 45.300323] usb 5-1: uhci_result_common: failed with status 440000
[ 45.301319] usb 5-1: uhci_result_common: failed with status 440000
[ 45.302312] usb 5-1: uhci_result_common: failed with status 440000
[ 45.303313] usb 5-1: uhci_result_common: failed with status 440000
[ 45.304314] usb 5-1: uhci_result_common: failed with status 440000
[ 45.305311] usb 5-1: uhci_result_common: failed with status 440000
[ 45.306311] usb 5-1: uhci_result_common: failed with status 440000
[ 45.307317] usb 5-1: uhci_result_common: failed with status 440000
[ 45.308309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.309309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.310315] usb 5-1: uhci_result_common: failed with status 440000
[ 45.311310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.312308] usb 5-1: uhci_result_common: failed with status 440000
[ 45.313309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.314317] usb 5-1: uhci_result_common: failed with status 440000
[ 45.315310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.316307] usb 5-1: uhci_result_common: failed with status 440000
[ 45.317315] usb 5-1: uhci_result_common: failed with status 440000
[ 45.318310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.319310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.320318] usb 5-1: uhci_result_common: failed with status 440000
[ 45.321308] usb 5-1: uhci_result_common: failed with status 440000
[ 45.322309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.323310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.324317] usb 5-1: uhci_result_common: failed with status 440000
[ 45.325307] usb 5-1: uhci_result_common: failed with status 440000
[ 45.326309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.327316] usb 5-1: uhci_result_common: failed with status 440000
[ 45.328311] usb 5-1: uhci_result_common: failed with status 440000
[ 45.329308] usb 5-1: uhci_result_common: failed with status 440000
[ 45.330315] usb 5-1: uhci_result_common: failed with status 440000
[ 45.331309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.332311] usb 5-1: uhci_result_common: failed with status 440000
[ 45.333307] usb 5-1: uhci_result_common: failed with status 440000
[ 45.334313] usb 5-1: uhci_result_common: failed with status 440000
[ 45.335310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.336310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.337318] usb 5-1: uhci_result_common: failed with status 440000
[ 45.338309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.339309] usb 5-1: uhci_result_common: failed with status 440000
[ 45.340315] usb 5-1: uhci_result_common: failed with status 440000
[ 45.341310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.342308] usb 5-1: uhci_result_common: failed with status 440000
[ 45.343308] usb 5-1: uhci_result_common: failed with status 440000
[ 45.344316] usb 5-1: uhci_result_common: failed with status 440000
[ 45.345310] usb 5-1: uhci_result_common: failed with status 440000
[ 45.346307] usb 5-1: uhci_result_common: failed with status 440000
[ 45.346850] usb 5-1: uhci_result_common: failed with status 440000
[ 45.347100] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0002
[ 45.347172] uhci_hcd 0000:00:1d.0: port 1 portsc 008a,00
[ 45.347233] usb 5-1: uhci_result_common: failed with status 440000
[ 45.347344] hub 5-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
[ 45.347392] usb 5-1: USB disconnect, address 4
[ 45.347434] usb 5-1: unregistering device
[ 45.347474] usb 5-1: usb_disable_device nuking all URBs
[ 45.347532] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d3019c0 ep1in-intr
[ 45.348252] uhci_hcd 0000:00:1d.0: release dev 4 ep81-INT, period 128, phase 0, 23 us
[ 45.348316] usb 5-1: uhci_result_common: failed with status 440000
[ 45.348414] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301c00 ep3in-bulk
[ 45.348465] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301180 ep3in-bulk
[ 45.348515] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301f00 ep3in-bulk
[ 45.348566] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d3010c0 ep3in-bulk
[ 45.348617] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301840 ep3in-bulk
[ 45.348667] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d3016c0 ep3in-bulk
[ 45.348717] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301b40 ep3in-bulk
[ 45.348768] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007e21ba80 ep3in-bulk
[ 45.348818] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007e21bd80 ep3in-bulk
[ 45.348869] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007e21b780 ep3in-bulk
[ 45.348919] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301cc0 ep3in-bulk
[ 45.348970] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301480 ep3in-bulk
[ 45.349020] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301540 ep3in-bulk
[ 45.349071] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301d80 ep3in-bulk
[ 45.349121] uhci_hcd 0000:00:1d.0: shutdown urb ffff88007d301a80 ep3in-bulk
[ 45.349225] usb 5-1: uhci_result_common: failed with status 440000
[ 45.349404] usb 5-1: unregistering interface 5-1:1.0
[ 45.349933] drivers/usb/class/cdc-acm.c:1335: acm_disconnect
[ 45.349968] drivers/usb/class/cdc-acm.c:1340: acm_disconnect
[ 45.350589] drivers/usb/class/cdc-acm.c:1335: acm_disconnect
[ 45.350920] drivers/usb/class/cdc-acm.c:1364: acm_disconnect
[ 45.350985] drivers/usb/class/cdc-acm.c:1370: acm_disconnect
[ 45.351051] drivers/usb/class/cdc-acm.c:1378: acm_disconnect
[ 45.351134] usb 5-1:1.0: uevent
[ 45.351892] tty_port_close_start: count = -1
[ 45.355438] usb 5-1: unregistering interface 5-1:1.1
[ 45.355795] usb 5-1:1.1: uevent
[ 45.359590] usb 5-1: unregistering interface 5-1:1.2
[ 45.359812] usb 5-1:1.2: uevent
[ 45.361937] usb 5-1: uevent
[ 45.480214] hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 46.596841] usb usb5: suspend_rh (auto-stop)
[ 48.346874] hub 5-0:1.0: hub_suspend
[ 48.346938] usb usb5: bus auto-suspend
[ 48.346979] usb usb5: suspend_rh
[ 72.741378] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 72.741470] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 72.741560] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 72.860223] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 72.913736] ehci_hcd 0000:00:1d.7: port 1 full speed --> companion
[ 72.913793] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT
[ 72.913905] hub 2-0:1.0: port 1 not reset yet, waiting 50ms
[ 72.913969] usb usb5: usb resume
[ 72.914008] usb usb5: wakeup_rh
[ 72.936419] EXT4-fs (sda5): barriers enabled
[ 72.946192] kjournald2 starting: pid 2108, dev sda5:8, commit interval 5 seconds
[ 72.946761] EXT4-fs (sda5): internal journal on sda5:8
[ 72.946838] EXT4-fs (sda5): delayed allocation enabled
[ 72.946910] EXT4-fs: file extents enabled
[ 72.947121] EXT4-fs: mballoc enabled
[ 72.947233] EXT4-fs (sda5): mounted filesystem with writeback data mode
[ 72.950243] hub 5-0:1.0: hub_resume
[ 72.950347] uhci_hcd 0000:00:1d.0: port 1 portsc 0093,00
[ 72.950402] hub 5-0:1.0: port 1: status 0101 change 0001
[ 72.966864] ehci_hcd 0000:00:1d.7: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC
[ 72.967009] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0002
[ 73.053575] hub 5-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 73.053658] hub 5-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 73.160197] usb 5-1: new full speed USB device using uhci_hcd and address 5
[ 73.286869] usb 5-1: ep0 maxpacket = 8
[ 73.315986] usb 5-1: skipped 4 descriptors after interface
[ 73.333980] usb 5-1: skipped 3 descriptors after interface
[ 73.336965] usb 5-1: default language 0x0409
[ 73.357972] usb 5-1: udev 5, busnum 5, minor = 516
[ 73.358022] usb 5-1: New USB device found, idVendor=1457, idProduct=5122
[ 73.358069] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 73.358117] usb 5-1: Product: RNDIS/Ethernet Gadget
[ 73.358157] usb 5-1: Manufacturer: Linux 2.6.24/s3c2410_udc
[ 73.358463] usb 5-1: uevent
[ 73.359366] usb 5-1: usb_probe_device
[ 73.359410] usb 5-1: configuration #1 chosen from 2 choices
[ 73.364866] usb 5-1: adding 5-1:1.0 (config #1, interface 0)
[ 73.366980] usb 5-1:1.0: uevent
[ 73.367405] usb 5-1: adding 5-1:1.1 (config #1, interface 1)
[ 73.367557] usb 5-1:1.1: uevent
[ 73.374300] usb 5-1: uevent
[ 73.536869] cdc_ether 5-1:1.0: usb_probe_interface
[ 73.536919] cdc_ether 5-1:1.0: usb_probe_interface - got id
[ 73.547923] usb0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, 5e:e8:8c:c5:9c:d1
[ 73.549226] usbcore: registered new interface driver cdc_ether
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 18:25 ` Alex Riesen
@ 2009-08-02 20:39 ` Alex Riesen
2009-08-02 20:50 ` Alan Stern
0 siblings, 1 reply; 11+ messages in thread
From: Alex Riesen @ 2009-08-02 20:39 UTC (permalink / raw)
To: Oliver Neukum
Cc: linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
On Sun, Aug 2, 2009 at 20:25, Alex Riesen<raa.lkml@gmail.com> wrote:
> I shall try to find the -rc2 which oopses (I suspect it is the one
> just before -rc3).
>
And this is after I put "for(;;);" at the end of dump_stack in v2.6.31-rc3:
http://home.arcor.de/fork0/bug/neocrash.jpg (~110k)
And this one is with v2.6.31-rc5 (it has usb_disconnect in it):
http://home.arcor.de/fork0/bug/neocrash-rc5.jpg (~86k)
(config: http://home.arcor.de/fork0/bug/neocrash-config-rc5.txt)
I couldn't find the -rc2 which didn't lock up. They all do now. I don't know
anymore how I made that -rc2 where I got the previous oops from.
Any idea how to disable stack dumps so that there is more place
for other output on a laptop screen? (no chance for serial console)
Or maybe a high-speed video camera can stand a chance?
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 20:39 ` Alex Riesen
@ 2009-08-02 20:50 ` Alan Stern
2009-08-02 21:09 ` Alex Riesen
0 siblings, 1 reply; 11+ messages in thread
From: Alan Stern @ 2009-08-02 20:50 UTC (permalink / raw)
To: Alex Riesen
Cc: Oliver Neukum, linux-usb, Oliver Neukum,
Linux Kernel Mailing List, Greg Kroah-Hartman, Alan Cox
On Sun, 2 Aug 2009, Alex Riesen wrote:
> Any idea how to disable stack dumps so that there is more place
> for other output on a laptop screen? (no chance for serial console)
Put a "return" statement at the start of dump_stack().
Alan Stern
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 20:50 ` Alan Stern
@ 2009-08-02 21:09 ` Alex Riesen
2009-08-02 21:22 ` Oliver Neukum
2009-08-03 9:17 ` Alex Riesen
0 siblings, 2 replies; 11+ messages in thread
From: Alex Riesen @ 2009-08-02 21:09 UTC (permalink / raw)
To: Alan Stern
Cc: Oliver Neukum, linux-usb, Oliver Neukum,
Linux Kernel Mailing List, Greg Kroah-Hartman, Alan Cox
On Sun, Aug 2, 2009 at 22:50, Alan Stern<stern@rowland.harvard.edu> wrote:
> On Sun, 2 Aug 2009, Alex Riesen wrote:
>
>> Any idea how to disable stack dumps so that there is more place
>> for other output on a laptop screen? (no chance for serial console)
>
> Put a "return" statement at the start of dump_stack().
>
That wasn't enough, but a "return" in die helped.
So, I connect the device, run its bootloader, which causes
a CDC ACM interface to appear. The /dev/ttyACM0 node
appears, and I open it (with minicom). Then I just switch
the device off and kernel oopses with:
uhci_hcd 0000:00:1d.0: release dev 4 ep81-INT, period 128, phase 0, 23 us
usb 5-1: uhci_result_common: failed with status 440000
usb 5-1: uhci_result_common: failed with status 440000
uhci_hcd 0000:00:1d.0: shutdown urb ffff88007de6bf00 ep3in-bulk
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP: [<ffffffffa005ce38>] acm_rx_tasklet+0x24e/0x3a3 [cdc_acm]
... something will be missing here
---[ end trace ...]---
Kernel panic - not syncing: Fatal exception in interrupt
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 21:09 ` Alex Riesen
@ 2009-08-02 21:22 ` Oliver Neukum
2009-08-02 21:25 ` Alex Riesen
2009-08-03 9:17 ` Alex Riesen
1 sibling, 1 reply; 11+ messages in thread
From: Oliver Neukum @ 2009-08-02 21:22 UTC (permalink / raw)
To: Alex Riesen
Cc: Alan Stern, linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
Am Sonntag, 2. August 2009 23:09:37 schrieb Alex Riesen:
> So, I connect the device, run its bootloader, which causes
> a CDC ACM interface to appear. The /dev/ttyACM0 node
> appears, and I open it (with minicom). Then I just switch
> the device off and kernel oopses with:
It oopses _before_ you terminate minicom?
Regards
Oliver
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 21:22 ` Oliver Neukum
@ 2009-08-02 21:25 ` Alex Riesen
0 siblings, 0 replies; 11+ messages in thread
From: Alex Riesen @ 2009-08-02 21:25 UTC (permalink / raw)
To: Oliver Neukum
Cc: Alan Stern, linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
On Sun, Aug 2, 2009 at 23:22, Oliver Neukum<oliver@neukum.org> wrote:
> Am Sonntag, 2. August 2009 23:09:37 schrieb Alex Riesen:
>> So, I connect the device, run its bootloader, which causes
>> a CDC ACM interface to appear. The /dev/ttyACM0 node
>> appears, and I open it (with minicom). Then I just switch
>> the device off and kernel oopses with:
>
> It oopses _before_ you terminate minicom?
>
Yes. minicom was running at the time, and had the ttyACM0 open.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-02 21:09 ` Alex Riesen
2009-08-02 21:22 ` Oliver Neukum
@ 2009-08-03 9:17 ` Alex Riesen
2009-08-03 13:04 ` Oliver Neukum
1 sibling, 1 reply; 11+ messages in thread
From: Alex Riesen @ 2009-08-03 9:17 UTC (permalink / raw)
To: Alan Stern
Cc: Oliver Neukum, linux-usb, Oliver Neukum,
Linux Kernel Mailing List, Greg Kroah-Hartman, Alan Cox
On Sun, Aug 2, 2009 at 23:09, Alex Riesen<raa.lkml@gmail.com> wrote:
> BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
> IP: [<ffffffffa005ce38>] acm_rx_tasklet+0x24e/0x3a3 [cdc_acm]
I tried to look a little around acm_rx_tasklet (cdc-acm.c, -rc5). I
think it is this code:
0000000000001bea <acm_rx_tasklet>:
...
1e27: 4d 8b 44 24 18 mov 0x18(%r12),%r8
1e2c: 89 f8 mov %edi,%eax
1e2e: c1 f8 0f sar $0xf,%eax
1e31: 83 e0 0f and $0xf,%eax
1e34: 48 8b 14 c2 mov (%rdx,%rax,8),%rdx
1e38: 0f b6 42 03 movzbl 0x3(%rdx),%eax ; I think it crashed here
which is this:
movq 24(%r12), %r8 # <variable>.base, temp.1149
movl %edi, %eax # D.22806, tmp117
sarl $15, %eax #, tmp117
andl $15, %eax #, tmp119
movq (%rdx,%rax,8), %rdx #, ep
movzbl 3(%rdx), %eax # <variable>.desc.bmAttributes,
<variable>.desc.bmAttributes
and correspondingly:
466 ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in : acm->dev->ep_out)
467 [usb_pipeendpoint(acm->rx_endpoint)];
468 if (usb_endpoint_xfer_int(&ep->desc))
So it looks like ep is NULL (usb_endpoint_xfer_int accesses desc.bmAttributes,
which is 3 bytes off the beginning of struct usb_host_endpoint (desc being the
first field in usb_host_endpoint).
Any help with further debugging is very much appreciated (because
I don't know where to continue yet).
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-03 9:17 ` Alex Riesen
@ 2009-08-03 13:04 ` Oliver Neukum
2009-08-03 13:22 ` Alex Riesen
0 siblings, 1 reply; 11+ messages in thread
From: Oliver Neukum @ 2009-08-03 13:04 UTC (permalink / raw)
To: Alex Riesen
Cc: Alan Stern, linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset="utf-8", Size: 866 bytes --]
Am Montag, 3. August 2009 11:17:05 schrieb Alex Riesen:> 466Â Â Â Â Â Â Â Â Â Â Â Â Â ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in :> acm->dev->ep_out)> 467Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â [usb_pipeendpoint(acm->rx_endpoint)];> 468Â Â Â Â Â Â Â Â Â Â Â Â Â if (usb_endpoint_xfer_int(&ep->desc))>> So it looks like ep is NULL (usb_endpoint_xfer_int accesses> desc.bmAttributes, which is 3 bytes off the beginning of struct> usb_host_endpoint (desc being the first field in usb_host_endpoint).
This tells you that the device has been disconnected. The questionis not why this function fails, but why it is called even though thedevice has been disconnected.
Regards Oliver
ÿôèº{.nÇ+‰·Ÿ®‰†+%ŠËÿ±éݶ\x17¥Šwÿº{.nÇ+‰·¥Š{±þG«éÿŠ{ayº\x1dʇڙë,j\a¢f£¢·hšïêÿ‘êçz_è®\x03(階ŠÝ¢j"ú\x1a¶^[m§ÿÿ¾\a«þG«éÿ¢¸?™¨èÚ&£ø§~á¶iO•æ¬z·švØ^\x14\x04\x1a¶^[m§ÿÿÃ\fÿ¶ìÿ¢¸?–I¥
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet
2009-08-03 13:04 ` Oliver Neukum
@ 2009-08-03 13:22 ` Alex Riesen
0 siblings, 0 replies; 11+ messages in thread
From: Alex Riesen @ 2009-08-03 13:22 UTC (permalink / raw)
To: Oliver Neukum
Cc: Alan Stern, linux-usb, Oliver Neukum, Linux Kernel Mailing List,
Greg Kroah-Hartman, Alan Cox
On Mon, Aug 3, 2009 at 15:04, Oliver Neukum<oliver@neukum.org> wrote:
> Am Montag, 3. August 2009 11:17:05 schrieb Alex Riesen:
>> 466 ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in :
>> acm->dev->ep_out)
>> 467 [usb_pipeendpoint(acm->rx_endpoint)];
>> 468 if (usb_endpoint_xfer_int(&ep->desc))
>>
>> So it looks like ep is NULL (usb_endpoint_xfer_int accesses
>> desc.bmAttributes, which is 3 bytes off the beginning of struct
>> usb_host_endpoint (desc being the first field in usb_host_endpoint).
>
> This tells you that the device has been disconnected. The question
> is not why this function fails, but why it is called even though the
> device has been disconnected.
Cool. How can I help?
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2009-08-03 13:22 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-08-02 16:40 Oops in CDC ACM after an Openmoko phone (neo1973) changes its usb interface from ACM to Ethernet Alex Riesen
2009-08-02 17:19 ` Oliver Neukum
2009-08-02 18:25 ` Alex Riesen
2009-08-02 20:39 ` Alex Riesen
2009-08-02 20:50 ` Alan Stern
2009-08-02 21:09 ` Alex Riesen
2009-08-02 21:22 ` Oliver Neukum
2009-08-02 21:25 ` Alex Riesen
2009-08-03 9:17 ` Alex Riesen
2009-08-03 13:04 ` Oliver Neukum
2009-08-03 13:22 ` Alex Riesen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox