[PATCH v4 0/2] Add support for Xiaomi Mi TV Stick

[PATCH v4 0/2] Add support for Xiaomi Mi TV Stick

[Ferass El Hafidi]

This patch series aims to add initial support for the Xiaomi Mi TV
Stick.

Xiaomi Mi TV Stick is a small Amlogic-based Android TV stick released in 
2020, and known as `xiaomi-aquaman` internally (in the downstream kernel,
u-boot, ...)
Its specifications are as follows:
 * Amlogic S805Y SoC (believed to be mostly identical to S805X)
 * 8 GB eMMC
 * 1 GB of RAM
 * Android TV 9, upgradable to Android TV 10

There are multiple variants:
 * 1. Green PCB, manufactured in 2020, known UART pinout (helpfully 
   labeled on the board)
 * 2. Blue PCB, not much documentation about it, presumably manufactured
   between 2021 and 2023
 * 3. Green PCB, manufactured in 2023, known UART pinout, some layout
   changes compared to the 2020 variant

Among these variants, there are many boards using multiple different
Wi-Fi chips.  Supporting all of them is out of scope for this patch
series.

As of the time of writing this has only been tested on the 3rd variant.
It is believed that software-wise all three work mostly the same (if we 
don't count Wi-Fi), but testing on the other variants would still be
appreciated.

The devicetree is based on the Amlogic P241 DTS.

Changes since v3 [1]:
 * typo fix (`vbus-supply` in `&usb`)

Changes since v2 [2]:
 * fix SoB/From mismatch

Changes since v1 [3]:
 * remove useless nodes: cvbs-connector, ethmac, internal_phy, ir
 * add `amlogic,s805y` DT binding section
 * add S805Y dtsi: meson-gxl-s805y.dtsi
 * adjust DT `model` to "Xiaomi Mi TV Stick (Aquaman)"
 * explain the changes being done a bit more in the commit message for
   the DT patch
 * drop `clocks` and `clock-names` from pwm_ef (background: [4])
 * change sound `model` to "XIAOMI-AQUAMAN"

[1]: https://lore.kernel.org/all/20250203091453.15751-1-funderscore@postmarketos.org/
[2]: https://lore.kernel.org/all/20250201193044.28856-1-funderscore@postmarketos.org/
[3]: https://lore.kernel.org/all/20250131200319.19996-1-funderscore@postmarketos.org/
[4]: https://lore.kernel.org/linux-amlogic/20241227212514.1376682-1-martin.blumenstingl@googlemail.com/

Ferass El Hafidi (2):
  dt-bindings: arm: amlogic: add S805Y and Mi TV Stick
  arm64: dts: amlogic: add support for xiaomi-aquaman/Mi TV Stick

 .../devicetree/bindings/arm/amlogic.yaml      |   7 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s805y-xiaomi-aquaman.dts        | 285 ++++++++++++++++++
 .../boot/dts/amlogic/meson-gxl-s805y.dtsi     |  10 +
 4 files changed, 303 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi

-- 
2.47.1

[PATCH v4 1/2] dt-bindings: arm: amlogic: add S805Y and Mi TV Stick

[Ferass El Hafidi]

Add support for the Amlogic S805Y SoC and the Xiaomi Mi TV Stick (aka.
xiaomi-aquaman).  The S805Y is very similar to the S805X, with just a
few minor differences.

Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 0647851ae..3403362e0 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -73,6 +73,13 @@ properties:
           - const: amlogic,s805x
           - const: amlogic,meson-gxl
 
+      - description: Boards with the Amlogic Meson GXL S805Y SoC
+        items:
+          - enum:
+              - xiaomi,aquaman
+          - const: amlogic,s805y
+          - const: amlogic,meson-gxl
+
       - description: Boards with the Amlogic Meson GXL S905W SoC
         items:
           - enum:
-- 
2.47.1

[PATCH v4 2/2] arm64: dts: amlogic: add support for xiaomi-aquaman/Mi TV Stick

[Ferass El Hafidi]

Xiaomi Mi TV Stick is a small Amlogic-based Android TV stick released in
2020.  It is known as `xiaomi-aquaman` internally.  Specifications:
 * Amlogic S805Y SoC
 * Android TV 9, upgradable to Android TV 10
 * 8 GB eMMC
 * 1 GB of RAM

The devicetree is based on p241's DT, with some changes to better match
the Mi TV Stick:
 * there is no Ethernet port, no IR, no CVBS connector on the stick
 * a white LED is present
 * adjust memory to have 1 GB of RAM available

Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s805y-xiaomi-aquaman.dts        | 285 ++++++++++++++++++
 .../boot/dts/amlogic/meson-gxl-s805y.dtsi     |  10 +
 3 files changed, 296 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2fbda8419..0921707f1 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805y-xiaomi-aquaman.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-mecool-kii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
new file mode 100644
index 000000000..ccd0029c0
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
+ * Based on meson-gxl-s805x-p241.dtb:
+ *  - Copyright (c) 2018 BayLibre, SAS.
+ *    Author: Neil Armstrong <narmstrong@baylibre.com>
+ *    Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/meson-aiu.h>
+
+#include "meson-gxl-s805y.dtsi"
+
+/ {
+	compatible = "xiaomi,aquaman", "amlogic,s805y", "amlogic,meson-gxl";
+	model = "Xiaomi Mi TV Stick (aquaman)";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+	};
+
+	au2: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		sound-name-prefix = "AU2";
+		VCC-supply = <&vcc_5v>;
+		enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-white {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	vddio_boot: regulator-vddio-boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_ao18: regulator-vddio-ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_5v: regulator-vcc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "XIAOMI-AQUAMAN";
+		audio-aux-devs = <&au2>;
+		audio-widgets = "Line", "Lineout";
+		audio-routing = "AU2 INL", "ACODEC LOLN",
+				"AU2 INR", "ACODEC LORN",
+				"Lineout", "AU2 OUTL",
+				"Lineout", "AU2 OUTR";
+		clocks = <&clkc CLKID_MPLL0>,
+			 <&clkc CLKID_MPLL1>,
+			 <&clkc CLKID_MPLL2>;
+
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+
+			codec-1 {
+				sound-dai = <&aiu AIU_ACODEC CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+
+		dai-link-3 {
+			sound-dai = <&aiu AIU_ACODEC CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&acodec>;
+			};
+		};
+	};
+};
+
+&acodec {
+	AVDD-supply = <&vddio_ao18>;
+	status = "okay";
+};
+
+&aiu {
+	status = "okay";
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "disabled";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+	vbus-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
new file mode 100644
index 000000000..49b29b71f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
+ */
+
+#include "meson-gxl-s805x.dtsi"
+
+/ {
+	compatible = "amlogic,s805y", "amlogic,meson-gxl";
+};
-- 
2.47.1

Re: [PATCH v4 1/2] dt-bindings: arm: amlogic: add S805Y and Mi TV Stick

[Krzysztof Kozlowski]

On 03/02/2025 18:43, Ferass El Hafidi wrote:
> Add support for the Amlogic S805Y SoC and the Xiaomi Mi TV Stick (aka.
> xiaomi-aquaman).  The S805Y is very similar to the S805X, with just a
> few minor differences.
> 
> Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
> ---
>  Documentation/devicetree/bindings/arm/amlogic.yaml | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>


Best regards,
Krzysztof

Re: [PATCH v4 2/2] arm64: dts: amlogic: add support for xiaomi-aquaman/Mi TV Stick

[exxxxkc]

> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> +	status = "disabled";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <50000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	/* WiFi firmware requires power to be kept while in suspend */
> +	keep-power-in-suspend;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
>
  um it seem the sdio wifi module/chip connected to sd_emmc_a it is 
actually connected to sd_emmc_b

i tried to enable sd_emmc_a but nothing showed up in the kernel thus i 
tried to enabled sdd_emmc_b and there are a sdio device showed in the 
kernel (sdio:c07v8888d8888)

<https://matrix.to/#/!bDDAcbaDDYYwsVgelj:pixie.town/$YUSQIZ-pF22j9-ElrCst8XCUg1pac7CzWbUinNZL9HI?via=pixie.town&via=matrix.org&via=dissonant.dev>

acc to https://paste.coreelec.org/CoolersHurry 
<https://paste.coreelec.org/CoolersHurry> it seem it is amlogic w1 chip ?

(well on my board it is amlogic w1. there are some variant that use 
other wifi chip )

Re: [PATCH v4 2/2] arm64: dts: amlogic: add support for xiaomi-aquaman/Mi TV Stick

[Ferass El Hafidi]

On Thu Feb 6, 2025 at 4:14 PM UTC, exxxxkc wrote:
>   um it seem the sdio wifi module/chip connected to sd_emmc_a it is 
> actually connected to sd_emmc_b
>
> i tried to enable sd_emmc_a but nothing showed up in the kernel thus i 
> tried to enabled sdd_emmc_b and there are a sdio device showed in the 
> kernel (sdio:c07v8888d8888)
>
> <https://matrix.to/#/!bDDAcbaDDYYwsVgelj:pixie.town/$YUSQIZ-pF22j9-ElrCst8XCUg1pac7CzWbUinNZL9HI?via=pixie.town&via=matrix.org&via=dissonant.dev>
>
> acc to https://paste.coreelec.org/CoolersHurry 
> <https://paste.coreelec.org/CoolersHurry> it seem it is amlogic w1 chip ?
>
> (well on my board it is amlogic w1. there are some variant that use 
> other wifi chip )

Good catch!  I'll see if I can mess around with that stuff a bit more at
some point.

Cheers!

Re: [PATCH v4 0/2] Add support for Xiaomi Mi TV Stick

[Ferass El Hafidi]

Hello,

Superseded by v5:
https://lore.kernel.org/all/20250319190150.31529-2-funderscore@postmarketos.org/

Thanks.