* [PATCH v5 00/12] Enable more nodes for the Xperia 10 III
@ 2026-11-16 22:50 erebion
2026-11-16 22:50 ` [PATCH v5 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED erebion
` (11 more replies)
0 siblings, 12 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Luca Weiss, Konrad Dybcio
Enable some more nodes for the Xperia 10 III.
Signed-off-by: erebion <erebion@erebion.eu>
---
Changes in v5:
- sort some nodes alphabetically
- fix firmware paths to use codename "lena" instead of "pdx213" for consistency with other device trees
- PM6150L thermals: fix commit message after removing RFC_CAM_THERM in v4
- Link to v4: https://patch.msgid.link/20261113-pdx213-upstream-3-v4-0-4b01c50a821c@erebion.eu
Changes in v4:
- &pm6150l_flash: fix extra zero for led-max-microamp value accidentally added in v3 (this was setting the max value 10x to high), remove Lua's Reviewed-by
- rename touch-en-regulator patch: fix rebase mishap and remove a regulator that's not part of this patch series, remove Konrad's Reviewed-by
- IPA: remove redundant properties that are now set in sm6350-lena board DTS, remove Luca's Reviewed-by
- fix pm7250b thermals after a rebase mishap
- pm8350: disable PON, as pm6350 already has it enabled, remove Konrad's Reviewed-by
- rear_cam_sensor: fix gpio to use correct one
- remove includes that aren't actually used
- re-order alphabetically: &pm6150l_adc before &pm6150l_gpios
- remove a superfluous tab at the closing brace of rear-cam-flash-therm@2
- enable remaining i2c busses: fix rebase mishap
- fix firmware paths to use upper-case "Sony" instead of lower-case "sony" for consistency with other DTs, reset Luca's Reviewed-by
- remove rear_cam_sensor, as it does not work and I haven't found the issue, will submit later when I get it actually working
- Link to v3: https://patch.msgid.link/20261102-pdx213-upstream-3-v3-0-cdc3be96d257@erebion.eu
Changes in v3:
- re-order some properties, generic properties first, then qcom,*
- &pm6150l_flash: fix led-max-microamp value
- rename touch-en-regulator to regulator-touch-en (to keep any future fixed-regulator sorted together as well)
- Bluetooth: remove incorrect property that does not exist
- Bluetooth, &qup_uart1_cts: do not overwrite a bias-disable with bias-bus-hold as it is not necessary
- &pm7250b_vbus: fix regulator-max-microamp value
- Remove comment from reserved-memory as suggested by Konrad Dybcio
- Squashed the patch enabling IPA into the one enabling ADSP, CDSP & MPSS, as suggested by Luca Weiss (therefore not adding the Reviewed-by from Konrad Dybcio)
- Configure thermals for PMK8350, PM7250B, PM650L as used in pdx213
- Enable remaining i2c busses
- Link to v2: https://patch.msgid.link/20260926-pdx213-upstream-3-v2-0-b4612e3eb536@erebion.eu
Changes in v2:
- Remove panel_reset_pin that shouldn't be part of this patch series
- Remove incorrect reg from mpss
- Fix conflicting bias pinctrl, as pinctrl nodes from sm6350.dtsi already contain a bias-* property
- Fix incorrect unit name in &pmk8350_vadc
- Link to v1: https://patch.msgid.link/20260926-pdx213-upstream-3-v1-0-1609c18b5c1d@erebion.eu
To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
erebion (12):
arm64: dts: qcom: sm6350-lena: Add flash LED
arm64: dts: qcom: sm6350-lena: rename touch-en-regulator
arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node
arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS
arm64: dts: qcom: sm6350-lena: Enable Bluetooth
arm64: dts: qcom: sm6350-lena: Enable wifi
arm64: dts: qcom: sm6350-lena: Enable PM7250B
arm64: dts: qcom: sm6350-lena: Enable PMK8350
arm64: dts: qcom: sm6350-lena: Add PM7250B thermals
arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals
arm64: dts: qcom: sm6350-lena: Add PM6150L thermals
arm64: dts: qcom: sm6350-lena: enable remaining i2c busses
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 457 ++++++++++++++++++++-
1 file changed, 456 insertions(+), 1 deletion(-)
---
base-commit: e5e04726cdd043e309677071ab1b65a4b18f422b
change-id: 20260829-pdx213-upstream-3-d0b80f749b5b
Best regards,
--
erebion <erebion@erebion.eu>
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v5 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
@ 2026-11-16 22:50 ` erebion
2026-11-16 22:50 ` [PATCH v5 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator erebion
` (10 subsequent siblings)
11 siblings, 0 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Luca Weiss
Add a node for the camera flash LED found on the Xperia 10 III
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
.../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 6e2bbf4f060ac..4d78c500d00d3 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,9 +4,11 @@
*/
/dts-v1/;
+#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include "sm6350.dtsi"
+#include "pm6150l.dtsi"
#include "pm6350.dtsi"
/ {
@@ -302,6 +304,19 @@ touchscreen@48 {
};
};
+&pm6150l_flash {
+ status = "okay";
+
+ led-0 {
+ function = LED_FUNCTION_FLASH;
+ color = <LED_COLOR_ID_WHITE>;
+ led-sources = <1>;
+ led-max-microamp = <150000>;
+ flash-max-microamp = <1000000>;
+ flash-max-timeout-us = <1280000>;
+ };
+};
+
&pm6350_gpios {
vol_down_n: vol-down-n-state {
pins = "gpio2";
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
2026-11-16 22:50 ` [PATCH v5 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED erebion
@ 2026-11-16 22:50 ` erebion
2026-11-16 22:50 ` [PATCH v5 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node erebion
` (9 subsequent siblings)
11 siblings, 0 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Luca Weiss
rename touch-en-regulator -> regulator-touch-en, to
keep any future fixed-regulator sorted together
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 4d78c500d00d3..ca44219e1a67d 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -46,7 +46,7 @@ key-volume-down {
};
};
- touch_en_vreg: touch-en-regulator {
+ touch_en_vreg: regulator-touch-en {
compatible = "regulator-fixed";
regulator-name = "touch_en_vreg";
gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
2026-11-16 22:50 ` [PATCH v5 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED erebion
2026-11-16 22:50 ` [PATCH v5 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator erebion
@ 2026-11-16 22:50 ` erebion
2026-11-16 22:50 ` [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS erebion
` (8 subsequent siblings)
11 siblings, 0 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Luca Weiss, Konrad Dybcio
Adds the qcom,rmtfs-mem node required for the modem
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index ca44219e1a67d..a393b7533ccbf 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,7 @@
*/
/dts-v1/;
+#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -54,6 +55,17 @@ touch_en_vreg: regulator-touch-en {
vin-supply = <&pm6350_l6>;
};
+
+ reserved-memory {
+ memory@fe901000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0xfe901000 0x0 0x280000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
+ };
+ };
};
&apps_rsc {
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (2 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 11:31 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth erebion
` (7 subsequent siblings)
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Enable the ADSP, CDSP, IPA and MPSS (Modem) nodes for the Xperia 10 III.
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 24 ++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index a393b7533ccbf..e8808865bf6fa 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -68,6 +68,12 @@ memory@fe901000 {
};
};
+&adsp {
+ firmware-name = "qcom/sm6350/Sony/lena/adsp.mbn";
+
+ status = "okay";
+};
+
&apps_rsc {
regulators-0 {
compatible = "qcom,pm6350-rpmh-regulators";
@@ -291,6 +297,12 @@ pm6150l_bob: bob {
};
};
+&cdsp {
+ firmware-name = "qcom/sm6350/Sony/lena/cdsp.mbn";
+
+ status = "okay";
+};
+
&gpi_dma0 {
status = "okay";
};
@@ -316,6 +328,18 @@ touchscreen@48 {
};
};
+&ipa {
+ firmware-name = "qcom/sm6350/Sony/lena/ipa_fws.mbn";
+
+ status = "okay";
+};
+
+&mpss {
+ firmware-name = "qcom/sm6350/Sony/lena/modem.mbn";
+
+ status = "okay";
+};
+
&pm6150l_flash {
status = "okay";
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (3 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS erebion
@ 2026-11-16 22:50 ` erebion
2026-11-16 22:50 ` [PATCH v5 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi erebion
` (6 subsequent siblings)
11 siblings, 0 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Configure the required regulators for Bluetooth and enable it on the
Xperia 10 III.
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 96 ++++++++++++++++++++++
1 file changed, 96 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index e8808865bf6fa..12bf5420530d3 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -19,6 +19,10 @@ / {
qcom,msm-id = <434 0x10000>, <459 0x10000>;
qcom,board-id = <0x1000b 0>;
+ aliases {
+ serial1 = &uart1;
+ };
+
chosen {
#address-cells = <2>;
#size-cells = <2>;
@@ -376,6 +380,32 @@ &qupv3_id_1 {
status = "okay";
};
+/* UART1: HS UART for Bluetooth */
+&qup_uart1_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ /delete-property/ bias-pull-down;
+ bias-disable;
+};
+
+&qup_uart1_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ /delete-property/ bias-disable;
+ bias-pull-up;
+};
+
+&qup_uart1_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ /delete-property/ bias-pull-up;
+ bias-disable;
+};
+
&sdc2_off_state {
sd-cd-pins {
pins = "gpio94";
@@ -419,6 +449,72 @@ ts_int_default: ts-int-default-state {
drive-strength = <2>;
bias-disable;
};
+
+ qup_uart1_sleep_cts: qup-uart1-sleep-cts-state {
+ pins = "gpio61";
+ function = "gpio";
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+ };
+
+ qup_uart1_sleep_rts: qup-uart1-sleep-rts-state {
+ pins = "gpio62";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart1_sleep_rx: qup-uart1-sleep-rx-state {
+ pins = "gpio64";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
+ pins = "gpio63";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+};
+
+&uart1 {
+ /delete-property/ interrupts;
+ interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 64 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sleep_rx>;
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3991-bt";
+ vddio-supply = <&pm6350_l11>;
+ vddxo-supply = <&pm6350_l7>;
+ vddrf-supply = <&pm6150l_l2>;
+ vddch0-supply = <&pm6150l_l10>;
+ firmware-name = "crnv32u.bin";
+ };
};
&usb_1 {
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (4 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth erebion
@ 2026-11-16 22:50 ` erebion
2026-11-16 22:50 ` [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B erebion
` (5 subsequent siblings)
11 siblings, 0 replies; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Luca Weiss, Konrad Dybcio
Configure regulators and enable it for the Xperia 10 III
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 12bf5420530d3..9d880f6baa531 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -541,3 +541,13 @@ &usb_1_qmpphy {
status = "okay";
};
+
+&wifi {
+ vdd-0.8-cx-mx-supply = <&pm6350_l4>;
+ vdd-1.8-xo-supply = <&pm6350_l7>;
+ vdd-1.3-rfa-supply = <&pm6150l_l2>;
+ vdd-3.3-ch0-supply = <&pm6150l_l10>;
+ vdd-3.3-ch1-supply = <&pm6150l_l11>;
+
+ status = "okay";
+};
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (5 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:05 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350 erebion
` (4 subsequent siblings)
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Konrad Dybcio
Enable PM7250B and some components on it for the Xperia 10 III.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 48 ++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 9d880f6baa531..697e1cfae72e0 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,10 @@
*/
/dts-v1/;
+/* PM7250B is configured to use SID2/3 */
+#define PM7250B_SID 2
+#define PM7250B_SID1 3
+
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
@@ -11,6 +15,7 @@
#include "sm6350.dtsi"
#include "pm6150l.dtsi"
#include "pm6350.dtsi"
+#include "pm7250b.dtsi"
/ {
model = "Sony Xperia 10 III";
@@ -372,6 +377,49 @@ &pm6350_resin {
status = "okay";
};
+&pm7250b_adc {
+ channel@4d {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ label = "charger_skin_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@4f {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ label = "conn_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+};
+
+&pm7250b_adc_tm {
+ status = "okay";
+
+ charger-skin-therm@0 {
+ reg = <0>;
+ io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ conn-therm@1 {
+ reg = <1>;
+ io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+};
+
+&pm7250b_vbus {
+ regulator-min-microamp = <500000>;
+ regulator-max-microamp = <1000000>;
+
+ status = "okay";
+};
+
&qupv3_id_0 {
status = "okay";
};
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (6 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:02 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals erebion
` (3 subsequent siblings)
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Configure and enable nodes for PMK8350 on the Xperia 10 III.
The phone has two PMICs which have a PON block, disable the PMK8350
PON and keep the PM6350 PON, as only one should be enabled.
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 697e1cfae72e0..50a235d6fb6df 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -8,7 +8,11 @@
#define PM7250B_SID 2
#define PM7250B_SID1 3
+/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */
+#define PMK8350_SID 6
+
#include <dt-bindings/firmware/qcom,scm.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -16,6 +20,7 @@
#include "pm6150l.dtsi"
#include "pm6350.dtsi"
#include "pm7250b.dtsi"
+#include "pmk8350.dtsi"
/ {
model = "Sony Xperia 10 III";
@@ -420,6 +425,35 @@ &pm7250b_vbus {
status = "okay";
};
+&pmk8350_adc_tm {
+ status = "okay";
+
+ xo-therm@0 {
+ reg = <0>;
+ io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,ratiometric;
+ };
+};
+
+&pmk8350_pon {
+ status = "disabled";
+};
+
+&pmk8350_rtc {
+ status = "okay";
+};
+
+&pmk8350_vadc {
+ channel@644 {
+ reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+ label = "xo_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+};
+
&qupv3_id_0 {
status = "okay";
};
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (7 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350 erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:06 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals erebion
` (2 subsequent siblings)
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Configure the thermals for the chg-skin-thermal and conn-therm thermistors connected to
PM7250B.
The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 50a235d6fb6df..0bb714eed13f4 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -80,6 +80,32 @@ memory@fe901000 {
qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
};
};
+
+ thermal-zones {
+ chg-skin-thermal {
+ thermal-sensors = <&pm7250b_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ conn-thermal {
+ thermal-sensors = <&pm7250b_adc_tm 1>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
};
&adsp {
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (8 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:08 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals erebion
2026-11-16 22:50 ` [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses erebion
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Configure the thermals for the xo-thermal thermistor connected to
PMK8350.
The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.
Signed-off-by: erebion <erebion@erebion.eu>
---
arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 0bb714eed13f4..b86fe11fd5296 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -105,6 +105,18 @@ active-config0 {
};
};
};
+
+ xo-thermal {
+ thermal-sensors = <&pmk8350_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
};
};
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (9 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:10 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses erebion
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion
Configure the thermals for the PA_THERM1, MSM_THERM, PA_THERM0,
CAM_FLASH_THERM and QUIET_THERM thermistors connected to
PM6150L.
Due to hardware constraints we can only register 4 zones with
pm6150l_adc_tm, the other 2 we can register via generic-adc-thermal.
RFC_CAM_THERM is intentionally omitted for now and will have to be
added once it is clear how it should be added.
The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.
Signed-off-by: erebion <erebion@erebion.eu>
---
.../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 160 +++++++++++++++++++++
1 file changed, 160 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index b86fe11fd5296..b19e76b3c1a75 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -81,6 +81,13 @@ memory@fe901000 {
};
};
+ msm_therm_sensor: thermal-sensor-msm {
+ compatible = "generic-adc-thermal";
+ #thermal-sensor-cells = <0>;
+ io-channels = <&pm6150l_adc ADC5_AMUX_THM2_100K_PU>;
+ io-channel-names = "sensor-channel";
+ };
+
thermal-zones {
chg-skin-thermal {
thermal-sensors = <&pm7250b_adc_tm 0>;
@@ -106,6 +113,74 @@ active-config0 {
};
};
+ pa0-thermal {
+ thermal-sensors = <&pm6150l_adc_tm 1>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa1-thermal {
+ thermal-sensors = <&pm6150l_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ quiet-thermal {
+ thermal-sensors = <&pm6150l_adc_tm 3>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ rfc-flash-thermal {
+ thermal-sensors = <&pm6150l_adc_tm 2>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ sdm-skin-thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <5000>;
+ thermal-sensors = <&msm_therm_sensor>;
+
+ trips {
+ trip0 {
+ temperature = <45000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <55000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+
xo-thermal {
thermal-sensors = <&pmk8350_adc_tm 0>;
@@ -392,6 +467,83 @@ &mpss {
status = "okay";
};
+&pm6150l_adc {
+ pinctrl-0 = <&pm6150l_adc_default>;
+ pinctrl-names = "default";
+
+ channel@4d {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ label = "pa_therm1";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@4e {
+ reg = <ADC5_AMUX_THM2_100K_PU>;
+ label = "msm_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@4f {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ label = "pa_therm0";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@54 {
+ reg = <ADC5_GPIO3_100K_PU>;
+ label = "rear_cam_flash_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+
+ channel@55 {
+ reg = <ADC5_GPIO4_100K_PU>;
+ label = "quiet_therm";
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,ratiometric;
+ };
+};
+
+&pm6150l_adc_tm {
+ status = "okay";
+
+ pa-therm1@0 {
+ reg = <0>;
+ io-channels = <&pm6150l_adc ADC5_AMUX_THM1_100K_PU>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,ratiometric;
+ };
+
+ pa-therm0@1 {
+ reg = <1>;
+ io-channels = <&pm6150l_adc ADC5_AMUX_THM3_100K_PU>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,ratiometric;
+ };
+
+ rear-cam-flash-therm@2 {
+ reg = <2>;
+ io-channels = <&pm6150l_adc ADC5_GPIO3_100K_PU>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,ratiometric;
+ };
+
+ quiet-therm@3 {
+ reg = <3>;
+ io-channels = <&pm6150l_adc ADC5_GPIO4_100K_PU>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,ratiometric;
+ };
+};
+
&pm6150l_flash {
status = "okay";
@@ -405,6 +557,14 @@ led-0 {
};
};
+&pm6150l_gpios {
+ pm6150l_adc_default: adc-default-state {
+ pins = "gpio7", "gpio10";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ bias-high-impedance;
+ };
+};
+
&pm6350_gpios {
vol_down_n: vol-down-n-state {
pins = "gpio2";
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
` (10 preceding siblings ...)
2026-11-16 22:50 ` [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals erebion
@ 2026-11-16 22:50 ` erebion
2026-11-17 12:11 ` Luca Weiss
11 siblings, 1 reply; 20+ messages in thread
From: erebion @ 2026-11-16 22:50 UTC (permalink / raw)
To: Neil Armstrong, Jessica Zhang, Maarten Lankhorst, Maxime Ripard,
Thomas Zimmermann, David Airlie, Simona Vetter, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
erebion, Konrad Dybcio
Enable all i2c busses where something is connected on this phone. Add
comments as placeholders for which components are still missing.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: erebion <erebion@erebion.eu>
---
.../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index b19e76b3c1a75..08647584af0ce 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -438,6 +438,13 @@ &gpi_dma1 {
status = "okay";
};
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* PN553 NFC @ 28 */
+};
+
&i2c8 {
clock-frequency = <400000>;
status = "okay";
@@ -455,6 +462,17 @@ touchscreen@48 {
};
};
+&i2c10 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* PM8008 PMIC @ 8 and 9 */
+ /* SMB1395 PMIC @ 34 and 35 */
+ /* AW882xx amplifier @ 34 */
+ /* Foursemi FS16xx amplifier @ 35 */
+ /* FSA4480 Analog Audio Switch @ 42 */
+};
+
&ipa {
firmware-name = "qcom/sm6350/Sony/lena/ipa_fws.mbn";
--
2.53.0
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS
2026-11-16 22:50 ` [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS erebion
@ 2026-11-17 11:31 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 11:31 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Enable the ADSP, CDSP, IPA and MPSS (Modem) nodes for the Xperia 10 III.
>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 24 ++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index a393b7533ccbf..e8808865bf6fa 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -68,6 +68,12 @@ memory@fe901000 {
> };
> };
>
> +&adsp {
> + firmware-name = "qcom/sm6350/Sony/lena/adsp.mbn";
> +
> + status = "okay";
> +};
> +
> &apps_rsc {
> regulators-0 {
> compatible = "qcom,pm6350-rpmh-regulators";
> @@ -291,6 +297,12 @@ pm6150l_bob: bob {
> };
> };
>
> +&cdsp {
> + firmware-name = "qcom/sm6350/Sony/lena/cdsp.mbn";
> +
> + status = "okay";
> +};
> +
> &gpi_dma0 {
> status = "okay";
> };
> @@ -316,6 +328,18 @@ touchscreen@48 {
> };
> };
>
> +&ipa {
> + firmware-name = "qcom/sm6350/Sony/lena/ipa_fws.mbn";
> +
> + status = "okay";
> +};
> +
> +&mpss {
> + firmware-name = "qcom/sm6350/Sony/lena/modem.mbn";
> +
> + status = "okay";
> +};
> +
> &pm6150l_flash {
> status = "okay";
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350
2026-11-16 22:50 ` [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350 erebion
@ 2026-11-17 12:02 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:02 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Configure and enable nodes for PMK8350 on the Xperia 10 III.
>
> The phone has two PMICs which have a PON block, disable the PMK8350
> PON and keep the PM6350 PON, as only one should be enabled.
>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 34 ++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 697e1cfae72e0..50a235d6fb6df 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -8,7 +8,11 @@
> #define PM7250B_SID 2
> #define PM7250B_SID1 3
>
> +/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */
> +#define PMK8350_SID 6
> +
> #include <dt-bindings/firmware/qcom,scm.h>
> +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
> #include <dt-bindings/leds/common.h>
> #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> @@ -16,6 +20,7 @@
> #include "pm6150l.dtsi"
> #include "pm6350.dtsi"
> #include "pm7250b.dtsi"
> +#include "pmk8350.dtsi"
>
> / {
> model = "Sony Xperia 10 III";
> @@ -420,6 +425,35 @@ &pm7250b_vbus {
> status = "okay";
> };
>
> +&pmk8350_adc_tm {
> + status = "okay";
> +
> + xo-therm@0 {
> + reg = <0>;
> + io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,ratiometric;
> + };
> +};
> +
> +&pmk8350_pon {
> + status = "disabled";
> +};
> +
> +&pmk8350_rtc {
> + status = "okay";
> +};
> +
> +&pmk8350_vadc {
> + channel@644 {
> + reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
> + label = "xo_therm";
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + };
> +};
> +
> &qupv3_id_0 {
> status = "okay";
> };
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B
2026-11-16 22:50 ` [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B erebion
@ 2026-11-17 12:05 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:05 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
Konrad Dybcio
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Enable PM7250B and some components on it for the Xperia 10 III.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 48 ++++++++++++++++++++++
> 1 file changed, 48 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 9d880f6baa531..697e1cfae72e0 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -4,6 +4,10 @@
> */
> /dts-v1/;
>
> +/* PM7250B is configured to use SID2/3 */
> +#define PM7250B_SID 2
> +#define PM7250B_SID1 3
> +
> #include <dt-bindings/firmware/qcom,scm.h>
> #include <dt-bindings/leds/common.h>
> #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> @@ -11,6 +15,7 @@
> #include "sm6350.dtsi"
> #include "pm6150l.dtsi"
> #include "pm6350.dtsi"
> +#include "pm7250b.dtsi"
>
> / {
> model = "Sony Xperia 10 III";
> @@ -372,6 +377,49 @@ &pm6350_resin {
> status = "okay";
> };
>
> +&pm7250b_adc {
> + channel@4d {
> + reg = <ADC5_AMUX_THM1_100K_PU>;
> + label = "charger_skin_therm";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +
> + channel@4f {
> + reg = <ADC5_AMUX_THM3_100K_PU>;
> + label = "conn_therm";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +};
> +
> +&pm7250b_adc_tm {
> + status = "okay";
> +
> + charger-skin-therm@0 {
> + reg = <0>;
> + io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + conn-therm@1 {
> + reg = <1>;
> + io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +};
> +
> +&pm7250b_vbus {
> + regulator-min-microamp = <500000>;
> + regulator-max-microamp = <1000000>;
> +
> + status = "okay";
> +};
> +
> &qupv3_id_0 {
> status = "okay";
> };
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals
2026-11-16 22:50 ` [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals erebion
@ 2026-11-17 12:06 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:06 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Configure the thermals for the chg-skin-thermal and conn-therm thermistors connected to
This line is a bit long. If you re-send, please wrap it.
> PM7250B.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
Could also be squashed into "Enable PM7250B" but also fine as a separate
patch imo.
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 26 ++++++++++++++++++++++
> 1 file changed, 26 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 50a235d6fb6df..0bb714eed13f4 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -80,6 +80,32 @@ memory@fe901000 {
> qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
> };
> };
> +
> + thermal-zones {
> + chg-skin-thermal {
> + thermal-sensors = <&pm7250b_adc_tm 0>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> +
> + conn-thermal {
> + thermal-sensors = <&pm7250b_adc_tm 1>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> + };
> };
>
> &adsp {
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals
2026-11-16 22:50 ` [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals erebion
@ 2026-11-17 12:08 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:08 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Configure the thermals for the xo-thermal thermistor connected to
> PMK8350.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
Same as pm7250b thermal patch, could be squashed into "Enable PMK8350"
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 0bb714eed13f4..b86fe11fd5296 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -105,6 +105,18 @@ active-config0 {
> };
> };
> };
> +
> + xo-thermal {
> + thermal-sensors = <&pmk8350_adc_tm 0>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> };
> };
>
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals
2026-11-16 22:50 ` [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals erebion
@ 2026-11-17 12:10 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:10 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Configure the thermals for the PA_THERM1, MSM_THERM, PA_THERM0,
> CAM_FLASH_THERM and QUIET_THERM thermistors connected to
> PM6150L.
>
> Due to hardware constraints we can only register 4 zones with
> pm6150l_adc_tm, the other 2 we can register via generic-adc-thermal.
>
> RFC_CAM_THERM is intentionally omitted for now and will have to be
> added once it is clear how it should be added.
>
> The trip points can really only be considered as placeholders, more
> configuration with cooling etc. can be added later.
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 160 +++++++++++++++++++++
> 1 file changed, 160 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index b86fe11fd5296..b19e76b3c1a75 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -81,6 +81,13 @@ memory@fe901000 {
> };
> };
>
> + msm_therm_sensor: thermal-sensor-msm {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&pm6150l_adc ADC5_AMUX_THM2_100K_PU>;
> + io-channel-names = "sensor-channel";
> + };
> +
> thermal-zones {
> chg-skin-thermal {
> thermal-sensors = <&pm7250b_adc_tm 0>;
> @@ -106,6 +113,74 @@ active-config0 {
> };
> };
>
> + pa0-thermal {
> + thermal-sensors = <&pm6150l_adc_tm 1>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> +
> + pa1-thermal {
> + thermal-sensors = <&pm6150l_adc_tm 0>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> +
> + quiet-thermal {
> + thermal-sensors = <&pm6150l_adc_tm 3>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> +
> + rfc-flash-thermal {
> + thermal-sensors = <&pm6150l_adc_tm 2>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "passive";
> + };
> + };
> + };
> +
> + sdm-skin-thermal {
> + polling-delay-passive = <1000>;
> + polling-delay = <5000>;
> + thermal-sensors = <&msm_therm_sensor>;
> +
> + trips {
> + trip0 {
> + temperature = <45000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <55000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> +
> xo-thermal {
> thermal-sensors = <&pmk8350_adc_tm 0>;
>
> @@ -392,6 +467,83 @@ &mpss {
> status = "okay";
> };
>
> +&pm6150l_adc {
> + pinctrl-0 = <&pm6150l_adc_default>;
> + pinctrl-names = "default";
> +
> + channel@4d {
> + reg = <ADC5_AMUX_THM1_100K_PU>;
> + label = "pa_therm1";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +
> + channel@4e {
> + reg = <ADC5_AMUX_THM2_100K_PU>;
> + label = "msm_therm";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +
> + channel@4f {
> + reg = <ADC5_AMUX_THM3_100K_PU>;
> + label = "pa_therm0";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +
> + channel@54 {
> + reg = <ADC5_GPIO3_100K_PU>;
> + label = "rear_cam_flash_therm";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +
> + channel@55 {
> + reg = <ADC5_GPIO4_100K_PU>;
> + label = "quiet_therm";
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + qcom,ratiometric;
> + };
> +};
> +
> +&pm6150l_adc_tm {
> + status = "okay";
> +
> + pa-therm1@0 {
> + reg = <0>;
> + io-channels = <&pm6150l_adc ADC5_AMUX_THM1_100K_PU>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,ratiometric;
> + };
> +
> + pa-therm0@1 {
> + reg = <1>;
> + io-channels = <&pm6150l_adc ADC5_AMUX_THM3_100K_PU>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,ratiometric;
> + };
> +
> + rear-cam-flash-therm@2 {
> + reg = <2>;
> + io-channels = <&pm6150l_adc ADC5_GPIO3_100K_PU>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,ratiometric;
> + };
> +
> + quiet-therm@3 {
> + reg = <3>;
> + io-channels = <&pm6150l_adc ADC5_GPIO4_100K_PU>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,ratiometric;
> + };
> +};
> +
> &pm6150l_flash {
> status = "okay";
>
> @@ -405,6 +557,14 @@ led-0 {
> };
> };
>
> +&pm6150l_gpios {
> + pm6150l_adc_default: adc-default-state {
> + pins = "gpio7", "gpio10";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + bias-high-impedance;
> + };
> +};
> +
> &pm6350_gpios {
> vol_down_n: vol-down-n-state {
> pins = "gpio2";
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses
2026-11-16 22:50 ` [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses erebion
@ 2026-11-17 12:11 ` Luca Weiss
0 siblings, 0 replies; 20+ messages in thread
From: Luca Weiss @ 2026-11-17 12:11 UTC (permalink / raw)
To: erebion, Neil Armstrong, Jessica Zhang, Maarten Lankhorst,
Maxime Ripard, Thomas Zimmermann, David Airlie, Simona Vetter,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-kernel, dri-devel, linux-arm-msm, devicetree, phone-devel,
Konrad Dybcio
On Mon Nov 16, 2026 at 11:50 PM CET, erebion wrote:
> Enable all i2c busses where something is connected on this phone. Add
> comments as placeholders for which components are still missing.
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: erebion <erebion@erebion.eu>
> ---
> .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index b19e76b3c1a75..08647584af0ce 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -438,6 +438,13 @@ &gpi_dma1 {
> status = "okay";
> };
>
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
If you resend, add a newline before 'status', also with i2c10
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
> +
> + /* PN553 NFC @ 28 */
> +};
> +
> &i2c8 {
> clock-frequency = <400000>;
> status = "okay";
> @@ -455,6 +462,17 @@ touchscreen@48 {
> };
> };
>
> +&i2c10 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + /* PM8008 PMIC @ 8 and 9 */
> + /* SMB1395 PMIC @ 34 and 35 */
> + /* AW882xx amplifier @ 34 */
> + /* Foursemi FS16xx amplifier @ 35 */
> + /* FSA4480 Analog Audio Switch @ 42 */
> +};
> +
> &ipa {
> firmware-name = "qcom/sm6350/Sony/lena/ipa_fws.mbn";
>
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2026-11-17 12:11 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-16 22:50 [PATCH v5 00/12] Enable more nodes for the Xperia 10 III erebion
2026-11-16 22:50 ` [PATCH v5 01/12] arm64: dts: qcom: sm6350-lena: Add flash LED erebion
2026-11-16 22:50 ` [PATCH v5 02/12] arm64: dts: qcom: sm6350-lena: rename touch-en-regulator erebion
2026-11-16 22:50 ` [PATCH v5 03/12] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node erebion
2026-11-16 22:50 ` [PATCH v5 04/12] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP, IPA & MPSS erebion
2026-11-17 11:31 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 05/12] arm64: dts: qcom: sm6350-lena: Enable Bluetooth erebion
2026-11-16 22:50 ` [PATCH v5 06/12] arm64: dts: qcom: sm6350-lena: Enable wifi erebion
2026-11-16 22:50 ` [PATCH v5 07/12] arm64: dts: qcom: sm6350-lena: Enable PM7250B erebion
2026-11-17 12:05 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 08/12] arm64: dts: qcom: sm6350-lena: Enable PMK8350 erebion
2026-11-17 12:02 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 09/12] arm64: dts: qcom: sm6350-lena: Add PM7250B thermals erebion
2026-11-17 12:06 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 10/12] arm64: dts: qcom: sm6350-lena: Add PMK8350 thermals erebion
2026-11-17 12:08 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 11/12] arm64: dts: qcom: sm6350-lena: Add PM6150L thermals erebion
2026-11-17 12:10 ` Luca Weiss
2026-11-16 22:50 ` [PATCH v5 12/12] arm64: dts: qcom: sm6350-lena: enable remaining i2c busses erebion
2026-11-17 12:11 ` Luca Weiss
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox