[PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[nicolas.ferre]

From: Nicolas Ferre <nicolas.ferre@microchip.com>

Change how the Backup Unit Power is configured and force the
automatic/hardware mode.
This change eliminates the need for software management of the power
switch, ensuring it transitions to the backup power source before
entering low power modes.

This is done in the only locaton where this swich was configured. It's
usually done in the bootloader.

Previously, the loss of the VDDANA (or VDDIN33) power source was not
automatically compensated by an alternative power source. This resulted
in the loss of Backup Unit content, including Backup Self-refresh low
power mode information, OTP emulation configuration, and boot
configuration, for instance.

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
---
 arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
 1 file changed, 20 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index b9b995f8a36e..05a1547642b6 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
 	return 0;
 }
 
-static void at91_pm_switch_ba_to_vbat(void)
+/**
+ * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
+ * to automatic/hardware mode.
+ *
+ * The Backup Unit Power Switch can be managed either by software or hardware.
+ * Enabling hardware mode allows the automatic transition of power between
+ * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
+ * availability of these power sources.
+ *
+ * If the Backup Unit Power Switch is already in automatic mode, no action is
+ * required. If it is in software-controlled mode, it is switched to automatic
+ * mode to enhance safety and eliminate the need for toggling between power
+ * sources.
+ */
+static void at91_pm_switch_ba_to_auto(void)
 {
 	unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
 	unsigned int val;
@@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
 
 	val = readl(soc_pm.data.sfrbu + offset);
 
-	/* Already on VBAT. */
-	if (!(val & soc_pm.sfrbu_regs.pswbu.state))
+	/* Already on auto/hardware. */
+	if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
 		return;
 
-	val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
-	val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
+	val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
+	val |= soc_pm.sfrbu_regs.pswbu.key;
 	writel(val, soc_pm.data.sfrbu + offset);
-
-	/* Wait for update. */
-	val = readl(soc_pm.data.sfrbu + offset);
-	while (val & soc_pm.sfrbu_regs.pswbu.state)
-		val = readl(soc_pm.data.sfrbu + offset);
 }
 
 static void at91_pm_suspend(suspend_state_t state)
 {
 	if (soc_pm.data.mode == AT91_PM_BACKUP) {
-		at91_pm_switch_ba_to_vbat();
+		at91_pm_switch_ba_to_auto();
 
 		cpu_suspend(0, at91_suspend_finish);
 
-- 
2.39.2

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Claudiu Beznea]

Hi, Nicolas,

On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
> From: Nicolas Ferre <nicolas.ferre@microchip.com>
> 
> Change how the Backup Unit Power is configured and force the
> automatic/hardware mode.
> This change eliminates the need for software management of the power
> switch, ensuring it transitions to the backup power source before
> entering low power modes.
> 
> This is done in the only locaton where this swich was configured. It's

s/locaton/location

> usually done in the bootloader.
> 
> Previously, the loss of the VDDANA (or VDDIN33) power source was not
> automatically compensated by an alternative power source. This resulted
> in the loss of Backup Unit content, including Backup Self-refresh low
> power mode information, OTP emulation configuration, and boot
> configuration, for instance.

Should we add a fixes for this?

> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
> ---
>  arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
>  1 file changed, 20 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
> index b9b995f8a36e..05a1547642b6 100644
> --- a/arch/arm/mach-at91/pm.c
> +++ b/arch/arm/mach-at91/pm.c
> @@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
>  	return 0;
>  }
>  
> -static void at91_pm_switch_ba_to_vbat(void)
> +/**
> + * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
> + * to automatic/hardware mode.
> + *
> + * The Backup Unit Power Switch can be managed either by software or hardware.
> + * Enabling hardware mode allows the automatic transition of power between
> + * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
> + * availability of these power sources.
> + *
> + * If the Backup Unit Power Switch is already in automatic mode, no action is
> + * required. If it is in software-controlled mode, it is switched to automatic
> + * mode to enhance safety and eliminate the need for toggling between power
> + * sources.
> + */
> +static void at91_pm_switch_ba_to_auto(void)
>  {
>  	unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
>  	unsigned int val;
> @@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
>  
>  	val = readl(soc_pm.data.sfrbu + offset);
>  
> -	/* Already on VBAT. */
> -	if (!(val & soc_pm.sfrbu_regs.pswbu.state))
> +	/* Already on auto/hardware. */
> +	if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
>  		return;
>  
> -	val &= ~soc_pm.sfrbu_regs.pswbu.softsw;

It seems that softsw and state members of at91_pm_sfrbu_regs.pswbu along
with their initialization could be dropped. What do you think?

I can do it while applying, if any.

Thank you,
Claudiu


> -	val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
> +	val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
> +	val |= soc_pm.sfrbu_regs.pswbu.key;
>  	writel(val, soc_pm.data.sfrbu + offset);
> -
> -	/* Wait for update. */
> -	val = readl(soc_pm.data.sfrbu + offset);
> -	while (val & soc_pm.sfrbu_regs.pswbu.state)
> -		val = readl(soc_pm.data.sfrbu + offset);
>  }
>  
>  static void at91_pm_suspend(suspend_state_t state)
>  {
>  	if (soc_pm.data.mode == AT91_PM_BACKUP) {
> -		at91_pm_switch_ba_to_vbat();
> +		at91_pm_switch_ba_to_auto();
>  
>  		cpu_suspend(0, at91_suspend_finish);
>  

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Nicolas Ferre]

On 02/12/2024 at 09:05, Claudiu Beznea wrote:
> Hi, Nicolas,
> 
> On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
>> From: Nicolas Ferre <nicolas.ferre@microchip.com>
>>
>> Change how the Backup Unit Power is configured and force the
>> automatic/hardware mode.
>> This change eliminates the need for software management of the power
>> switch, ensuring it transitions to the backup power source before
>> entering low power modes.
>>
>> This is done in the only locaton where this swich was configured. It's
> 
> s/locaton/location
> 
>> usually done in the bootloader.
>>
>> Previously, the loss of the VDDANA (or VDDIN33) power source was not
>> automatically compensated by an alternative power source. This resulted
>> in the loss of Backup Unit content, including Backup Self-refresh low
>> power mode information, OTP emulation configuration, and boot
>> configuration, for instance.
> 
> Should we add a fixes for this?

Not so easy to tell as there's a loose dependency with the bootloader. 
But it's true that switching to automatic never harm. So probably yes.

>> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
>> ---
>>   arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
>>   1 file changed, 20 insertions(+), 11 deletions(-)
>>
>> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
>> index b9b995f8a36e..05a1547642b6 100644
>> --- a/arch/arm/mach-at91/pm.c
>> +++ b/arch/arm/mach-at91/pm.c
>> @@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
>>        return 0;
>>   }
>>
>> -static void at91_pm_switch_ba_to_vbat(void)
>> +/**
>> + * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
>> + * to automatic/hardware mode.
>> + *
>> + * The Backup Unit Power Switch can be managed either by software or hardware.
>> + * Enabling hardware mode allows the automatic transition of power between
>> + * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
>> + * availability of these power sources.
>> + *
>> + * If the Backup Unit Power Switch is already in automatic mode, no action is
>> + * required. If it is in software-controlled mode, it is switched to automatic
>> + * mode to enhance safety and eliminate the need for toggling between power
>> + * sources.
>> + */
>> +static void at91_pm_switch_ba_to_auto(void)
>>   {
>>        unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
>>        unsigned int val;
>> @@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
>>
>>        val = readl(soc_pm.data.sfrbu + offset);
>>
>> -     /* Already on VBAT. */
>> -     if (!(val & soc_pm.sfrbu_regs.pswbu.state))
>> +     /* Already on auto/hardware. */
>> +     if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
>>                return;
>>
>> -     val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
> 
> It seems that softsw and state members of at91_pm_sfrbu_regs.pswbu along
> with their initialization could be dropped. What do you think?

I think that I tried when writing the patch but I think that there's a 
little difference with sama5d2 register layout. Give me a couple more 
days to come back to this and verify.

> I can do it while applying, if any.
> 
> Thank you,
> Claudiu
> 
> 
>> -     val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
>> +     val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
>> +     val |= soc_pm.sfrbu_regs.pswbu.key;
>>        writel(val, soc_pm.data.sfrbu + offset);
>> -
>> -     /* Wait for update. */
>> -     val = readl(soc_pm.data.sfrbu + offset);
>> -     while (val & soc_pm.sfrbu_regs.pswbu.state)
>> -             val = readl(soc_pm.data.sfrbu + offset);
>>   }
>>
>>   static void at91_pm_suspend(suspend_state_t state)
>>   {
>>        if (soc_pm.data.mode == AT91_PM_BACKUP) {
>> -             at91_pm_switch_ba_to_vbat();
>> +             at91_pm_switch_ba_to_auto();
>>
>>                cpu_suspend(0, at91_suspend_finish);
>>

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Nicolas Ferre]

Claudiu,

On 02/12/2024 at 17:44, Nicolas Ferre wrote:
> On 02/12/2024 at 09:05, Claudiu Beznea wrote:
>> Hi, Nicolas,
>>
>> On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
>>> From: Nicolas Ferre <nicolas.ferre@microchip.com>
>>>
>>> Change how the Backup Unit Power is configured and force the
>>> automatic/hardware mode.
>>> This change eliminates the need for software management of the power
>>> switch, ensuring it transitions to the backup power source before
>>> entering low power modes.
>>>
>>> This is done in the only locaton where this swich was configured. It's
>>
>> s/locaton/location
>>
>>> usually done in the bootloader.
>>>
>>> Previously, the loss of the VDDANA (or VDDIN33) power source was not
>>> automatically compensated by an alternative power source. This resulted
>>> in the loss of Backup Unit content, including Backup Self-refresh low
>>> power mode information, OTP emulation configuration, and boot
>>> configuration, for instance.
>>
>> Should we add a fixes for this?
> 
> Not so easy to tell as there's a loose dependency with the bootloader.
> But it's true that switching to automatic never harm. So probably yes.
> 
>>> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
>>> ---
>>>    arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
>>>    1 file changed, 20 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
>>> index b9b995f8a36e..05a1547642b6 100644
>>> --- a/arch/arm/mach-at91/pm.c
>>> +++ b/arch/arm/mach-at91/pm.c
>>> @@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
>>>         return 0;
>>>    }
>>>
>>> -static void at91_pm_switch_ba_to_vbat(void)
>>> +/**
>>> + * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
>>> + * to automatic/hardware mode.
>>> + *
>>> + * The Backup Unit Power Switch can be managed either by software or hardware.
>>> + * Enabling hardware mode allows the automatic transition of power between
>>> + * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
>>> + * availability of these power sources.
>>> + *
>>> + * If the Backup Unit Power Switch is already in automatic mode, no action is
>>> + * required. If it is in software-controlled mode, it is switched to automatic
>>> + * mode to enhance safety and eliminate the need for toggling between power
>>> + * sources.
>>> + */
>>> +static void at91_pm_switch_ba_to_auto(void)
>>>    {
>>>         unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
>>>         unsigned int val;
>>> @@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
>>>
>>>         val = readl(soc_pm.data.sfrbu + offset);
>>>
>>> -     /* Already on VBAT. */
>>> -     if (!(val & soc_pm.sfrbu_regs.pswbu.state))
>>> +     /* Already on auto/hardware. */
>>> +     if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
>>>                 return;
>>>
>>> -     val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
>>
>> It seems that softsw and state members of at91_pm_sfrbu_regs.pswbu along
>> with their initialization could be dropped. What do you think?
> 
> I think that I tried when writing the patch but I think that there's a
> little difference with sama5d2 register layout. Give me a couple more
> days to come back to this and verify.

Ok, I remember now: I was wondering if I needed to remove the whole 
sfrbu_regs.xxx mechanism and define more generically the content of 
include/soc/at91/sama7-sfrbu.h for sama5d2, but if we need one day to 
use the STATE bit or even the SMCTRL bit of sama5d2, then it should be kept.

So, now that the mechanism is in place, I would prefer that we keep it: 
okay for you?

Do you want me to re-spin a v2 for the rest?

Best regards,
   Nicolas

>> I can do it while applying, if any.
>>
>> Thank you,
>> Claudiu
>>
>>
>>> -     val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
>>> +     val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
>>> +     val |= soc_pm.sfrbu_regs.pswbu.key;
>>>         writel(val, soc_pm.data.sfrbu + offset);
>>> -
>>> -     /* Wait for update. */
>>> -     val = readl(soc_pm.data.sfrbu + offset);
>>> -     while (val & soc_pm.sfrbu_regs.pswbu.state)
>>> -             val = readl(soc_pm.data.sfrbu + offset);
>>>    }
>>>
>>>    static void at91_pm_suspend(suspend_state_t state)
>>>    {
>>>         if (soc_pm.data.mode == AT91_PM_BACKUP) {
>>> -             at91_pm_switch_ba_to_vbat();
>>> +             at91_pm_switch_ba_to_auto();
>>>
>>>                 cpu_suspend(0, at91_suspend_finish);
>>>
> 
> 

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Claudiu Beznea]

Hi, Nicolas,

On 06.12.2024 16:14, Nicolas Ferre wrote:
> Claudiu,
> 
> On 02/12/2024 at 17:44, Nicolas Ferre wrote:
>> On 02/12/2024 at 09:05, Claudiu Beznea wrote:
>>> Hi, Nicolas,
>>>
>>> On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
>>>> From: Nicolas Ferre <nicolas.ferre@microchip.com>
>>>>
>>>> Change how the Backup Unit Power is configured and force the
>>>> automatic/hardware mode.
>>>> This change eliminates the need for software management of the power
>>>> switch, ensuring it transitions to the backup power source before
>>>> entering low power modes.
>>>>
>>>> This is done in the only locaton where this swich was configured. It's
>>>
>>> s/locaton/location
>>>
>>>> usually done in the bootloader.
>>>>
>>>> Previously, the loss of the VDDANA (or VDDIN33) power source was not
>>>> automatically compensated by an alternative power source. This resulted
>>>> in the loss of Backup Unit content, including Backup Self-refresh low
>>>> power mode information, OTP emulation configuration, and boot
>>>> configuration, for instance.
>>>
>>> Should we add a fixes for this?
>>
>> Not so easy to tell as there's a loose dependency with the bootloader.
>> But it's true that switching to automatic never harm. So probably yes.
>>
>>>> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
>>>> ---
>>>>    arch/arm/mach-at91/pm.c | 31 ++++++++++++++++++++-----------
>>>>    1 file changed, 20 insertions(+), 11 deletions(-)
>>>>
>>>> diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
>>>> index b9b995f8a36e..05a1547642b6 100644
>>>> --- a/arch/arm/mach-at91/pm.c
>>>> +++ b/arch/arm/mach-at91/pm.c
>>>> @@ -598,7 +598,21 @@ static int at91_suspend_finish(unsigned long val)
>>>>         return 0;
>>>>    }
>>>>
>>>> -static void at91_pm_switch_ba_to_vbat(void)
>>>> +/**
>>>> + * at91_pm_switch_ba_to_auto() - Configure Backup Unit Power Switch
>>>> + * to automatic/hardware mode.
>>>> + *
>>>> + * The Backup Unit Power Switch can be managed either by software or
>>>> hardware.
>>>> + * Enabling hardware mode allows the automatic transition of power
>>>> between
>>>> + * VDDANA (or VDDIN33) and VDDBU (or VBAT, respectively), based on the
>>>> + * availability of these power sources.
>>>> + *
>>>> + * If the Backup Unit Power Switch is already in automatic mode, no
>>>> action is
>>>> + * required. If it is in software-controlled mode, it is switched to
>>>> automatic
>>>> + * mode to enhance safety and eliminate the need for toggling between
>>>> power
>>>> + * sources.
>>>> + */
>>>> +static void at91_pm_switch_ba_to_auto(void)
>>>>    {
>>>>         unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
>>>>         unsigned int val;
>>>> @@ -609,24 +623,19 @@ static void at91_pm_switch_ba_to_vbat(void)
>>>>
>>>>         val = readl(soc_pm.data.sfrbu + offset);
>>>>
>>>> -     /* Already on VBAT. */
>>>> -     if (!(val & soc_pm.sfrbu_regs.pswbu.state))
>>>> +     /* Already on auto/hardware. */
>>>> +     if (!(val & soc_pm.sfrbu_regs.pswbu.ctrl))
>>>>                 return;
>>>>
>>>> -     val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
>>>
>>> It seems that softsw and state members of at91_pm_sfrbu_regs.pswbu along
>>> with their initialization could be dropped. What do you think?
>>
>> I think that I tried when writing the patch but I think that there's a
>> little difference with sama5d2 register layout. Give me a couple more
>> days to come back to this and verify.
> 
> Ok, I remember now: I was wondering if I needed to remove the whole
> sfrbu_regs.xxx mechanism and define more generically the content of
> include/soc/at91/sama7-sfrbu.h for sama5d2, but if we need one day to use
> the STATE bit or even the SMCTRL bit of sama5d2, then it should be kept.
> 
> So, now that the mechanism is in place, I would prefer that we keep it:
> okay for you?

OK

> 
> Do you want me to re-spin a v2 for the rest?

No, I can handle the insignificant typo while applying.

Thank you,
Claudiu

> 
> Best regards,
>   Nicolas
> 
>>> I can do it while applying, if any.
>>>
>>> Thank you,
>>> Claudiu
>>>
>>>
>>>> -     val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
>>>> +     val &= ~soc_pm.sfrbu_regs.pswbu.ctrl;
>>>> +     val |= soc_pm.sfrbu_regs.pswbu.key;
>>>>         writel(val, soc_pm.data.sfrbu + offset);
>>>> -
>>>> -     /* Wait for update. */
>>>> -     val = readl(soc_pm.data.sfrbu + offset);
>>>> -     while (val & soc_pm.sfrbu_regs.pswbu.state)
>>>> -             val = readl(soc_pm.data.sfrbu + offset);
>>>>    }
>>>>
>>>>    static void at91_pm_suspend(suspend_state_t state)
>>>>    {
>>>>         if (soc_pm.data.mode == AT91_PM_BACKUP) {
>>>> -             at91_pm_switch_ba_to_vbat();
>>>> +             at91_pm_switch_ba_to_auto();
>>>>
>>>>                 cpu_suspend(0, at91_suspend_finish);
>>>>
>>
>>
> 

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Claudiu Beznea]

On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
> From: Nicolas Ferre <nicolas.ferre@microchip.com>
> 
> Change how the Backup Unit Power is configured and force the
> automatic/hardware mode.
> This change eliminates the need for software management of the power
> switch, ensuring it transitions to the backup power source before
> entering low power modes.
> 
> This is done in the only locaton where this swich was configured. It's
> usually done in the bootloader.
> 
> Previously, the loss of the VDDANA (or VDDIN33) power source was not
> automatically compensated by an alternative power source. This resulted
> in the loss of Backup Unit content, including Backup Self-refresh low
> power mode information, OTP emulation configuration, and boot
> configuration, for instance.
> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>

I've added the fixes tag, s/locaton/location, s/swich/switch.

Applied to at91-soc, thanks!

Re: [PATCH] ARM: at91: pm: change BU Power Switch to automatic mode

[Nicolas Ferre]

On 08/12/2024 at 16:48, Claudiu Beznea wrote:
> On 25.11.2024 18:56, nicolas.ferre@microchip.com wrote:
>> From: Nicolas Ferre <nicolas.ferre@microchip.com>
>>
>> Change how the Backup Unit Power is configured and force the
>> automatic/hardware mode.
>> This change eliminates the need for software management of the power
>> switch, ensuring it transitions to the backup power source before
>> entering low power modes.
>>
>> This is done in the only locaton where this swich was configured. It's
>> usually done in the bootloader.
>>
>> Previously, the loss of the VDDANA (or VDDIN33) power source was not
>> automatically compensated by an alternative power source. This resulted
>> in the loss of Backup Unit content, including Backup Self-refresh low
>> power mode information, OTP emulation configuration, and boot
>> configuration, for instance.
>>
>> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
> 
> I've added the fixes tag, s/locaton/location, s/swich/switch.

Thanks for your help Claudiu. Regards,
   Nicolas
> 
> Applied to at91-soc, thanks!