[PATCH 1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency

[PATCH 1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency

[Garrett Giordano]

The gpio-expander on i2c-1 has a maximum frequency of 100kHz. Update our
main_i2c1 frequency to allow the nxp,pcf8574 gpio-expander to function
properly.

Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
---
 arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
index a438baf542c2..171354b13e33 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
@@ -187,7 +187,7 @@ cpsw3g_phy3: ethernet-phy@3 {
 &main_i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 	status = "okay";
 
 	gpio_exp: gpio-expander@21 {
-- 
2.25.1

[PATCH 2/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add HDMI support

[Garrett Giordano]

The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.

Add pinmux for DSS DPI output and HDMI Interrupt.

Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the phyBOARD-Lyra.

Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.

Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
---
 .../dts/ti/k3-am625-phyboard-lyra-rdk.dts     | 94 +++++++++++++++++++
 1 file changed, 94 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
index 171354b13e33..81319d68b624 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
@@ -35,6 +35,18 @@ can_tc1: can-phy0 {
 		standby-gpios = <&gpio_exp 1 GPIO_ACTIVE_HIGH>;
 	};
 
+	hdmi0: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&sii9022_out>;
+			};
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -93,6 +105,37 @@ AM62X_IOPAD(0x244, PIN_INPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
 		>;
 	};
 
+	hdmi_int_pins_default: hdmi-int-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT, 7) /* (N23) GPMC0_AD1.GPIO0_16 */
+		>;
+	};
+
+	main_dss0_pins_default: main-dss0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+			AM62X_IOPAD(0x0bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+			AM62X_IOPAD(0x0e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+			AM62X_IOPAD(0x0e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+			AM62X_IOPAD(0x0e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+			AM62X_IOPAD(0x0ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
+			AM62X_IOPAD(0x0f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+			AM62X_IOPAD(0x0f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+			AM62X_IOPAD(0x0c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+			AM62X_IOPAD(0x0c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+			AM62X_IOPAD(0x0c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+			AM62X_IOPAD(0x0cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+			AM62X_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+			AM62X_IOPAD(0x0d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+			AM62X_IOPAD(0x0d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+			AM62X_IOPAD(0x0dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+			AM62X_IOPAD(0x0fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+			AM62X_IOPAD(0x0f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+			AM62X_IOPAD(0x104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+			AM62X_IOPAD(0x100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+		>;
+	};
+
 	main_i2c1_pins_default: main-i2c1-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
@@ -184,6 +227,26 @@ cpsw3g_phy3: ethernet-phy@3 {
 	};
 };
 
+&dss {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_dss0_pins_default>;
+	status = "okay";
+};
+
+&dss_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* VP2: DPI/HDMI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
+
 &main_i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
@@ -207,6 +270,37 @@ gpio_exp: gpio-expander@21 {
 				  "GPIO6_ETH1_USER_RESET", "GPIO7_AUDIO_USER_RESET";
 	};
 
+	sii9022: bridge-hdmi@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_int_pins_default>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022_in: endpoint {
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
 	eeprom@51 {
 		compatible = "atmel,24c02";
 		pagesize = <16>;
-- 
2.25.1

[PATCH 3/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Remove HDMI Reset Line Name

[Garrett Giordano]

The GPIO Expander has a line name defined as GPIO0_HDMI_RST. This line
is no longer associated with the HDMI Reset so we removed it.

Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
---
 arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
index 81319d68b624..4bc0134c987d 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
@@ -264,7 +264,7 @@ gpio_exp: gpio-expander@21 {
 		gpio-controller;
 		interrupt-controller;
 		#interrupt-cells = <2>;
-		gpio-line-names = "GPIO0_HDMI_RST", "GPIO1_CAN0_nEN",
+		gpio-line-names = "", "GPIO1_CAN0_nEN",
 				  "GPIO2_LED2", "GPIO3_LVDS_GPIO",
 				  "GPIO4_BUT2", "GPIO5_LVDS_BKLT_EN",
 				  "GPIO6_ETH1_USER_RESET", "GPIO7_AUDIO_USER_RESET";
-- 
2.25.1

Re: [PATCH 1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency

[Nishanth Menon]

On 14:28-20231204, Garrett Giordano wrote:
> The gpio-expander on i2c-1 has a maximum frequency of 100kHz. Update our
> main_i2c1 frequency to allow the nxp,pcf8574 gpio-expander to function
> properly.
> 
> Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> index a438baf542c2..171354b13e33 100644
> --- a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> @@ -187,7 +187,7 @@ cpsw3g_phy3: ethernet-phy@3 {
>  &main_i2c1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&main_i2c1_pins_default>;
> -	clock-frequency = <400000>;
> +	clock-frequency = <100000>;
>  	status = "okay";
>  
>  	gpio_exp: gpio-expander@21 {
> -- 
> 2.25.1
> 
https://lore.kernel.org/all/bd5284ec-6f25-464a-9ee7-4c50496482f1@phytec.de/

please make sure to pick up the previous Reviewed-by when you post an
update of your series.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency

[Wadim Egorov]

Am 04.12.23 um 23:28 schrieb Garrett Giordano:
> The gpio-expander on i2c-1 has a maximum frequency of 100kHz. Update our
> main_i2c1 frequency to allow the nxp,pcf8574 gpio-expander to function
> properly.
>
> Signed-off-by: Garrett Giordano <ggiordano@phytec.com>

For all three,
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>


> ---
>   arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts | 2 +-
>   1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> index a438baf542c2..171354b13e33 100644
> --- a/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am625-phyboard-lyra-rdk.dts
> @@ -187,7 +187,7 @@ cpsw3g_phy3: ethernet-phy@3 {
>   &main_i2c1 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_i2c1_pins_default>;
> -	clock-frequency = <400000>;
> +	clock-frequency = <100000>;
>   	status = "okay";
>   
>   	gpio_exp: gpio-expander@21 {

Re: [PATCH 1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency

[Nishanth Menon]

Hi Garrett Giordano,

On Mon, 04 Dec 2023 14:28:09 -0800, Garrett Giordano wrote:
> The gpio-expander on i2c-1 has a maximum frequency of 100kHz. Update our
> main_i2c1 frequency to allow the nxp,pcf8574 gpio-expander to function
> properly.
> 
> 

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Lower I2C1 frequency
      commit: 9c316d58c238e58d6346458462e8b0fd308e7332
[2/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add HDMI support
      commit: bac441710306a84c52f0f9a561aa9839b91caa14
[3/3] arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Remove HDMI Reset Line Name
      commit: fecdf6de7e47849504d0edaaff55fa0baadef420

For future reference: using a cover-letter (though not mandatory)
helps reviewers provide a ack/ other tag on cover letter to apply to
all patches and b4 can easily figure it out.

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D