[PATCH v2] scsi: storvsc: Support manual scans for all Hyper-V targets

[PATCH v2] scsi: storvsc: Support manual scans for all Hyper-V targets

[Laurence Oberman]

The Fibre Channel transport topology created by storvsc exposes only one
dummy remote port per SCSI host. Its scsi_target_id is always zero.

As a result, the FC transport user-scan path looks up the remote port using
target ID 0. It cannot initiate a scan for Target 1 or higher. No SCSI
command is therefore sent to Hyper-V when userspace explicitly requests a
scan of one of these targets.

storvsc itself supports up to STORVSC_FC_MAX_TARGETS and already passes
scmnd->device->id to Hyper-V as vm_srb->target_id. Devices on Target 1 and
higher work when initially discovered. They can also be rediscovered by a
full host scan, such as the scan triggered after an FC port bounce.

Provide a storvsc-specific user_scan callback that uses the exported
scsi_scan_target() interface. Iterate over the requested channel and target
ranges so that wildcard and explicitly addressed scans retain the expected
SCSI sysfs scan semantics.

This bypasses the single-rport lookup in fc_user_scan() and allows
userspace to explicitly scan any target supported by storvsc without
requiring one synthetic fc_rport for every Hyper-V target.

Signed-off-by: Laurence Oberman <loberman@redhat.com>
---

Changes in v2:
- Replace the private, unexported scsi_scan_host_selected() helper with
  the exported scsi_scan_target() interface.
- Preserve wildcard channel and target scan behavior.
- Verify that storvsc_eh_timed_out() does not use the FC error-handler
  helpers; the reported missing-rport dereference is not present.

 drivers/scsi/storvsc_drv.c | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/drivers/scsi/storvsc_drv.c b/drivers/scsi/storvsc_drv.c
index 571ea549152b..58b6ae96d03f 100644
--- a/drivers/scsi/storvsc_drv.c
+++ b/drivers/scsi/storvsc_drv.c
@@ -520,6 +520,36 @@ static void storvsc_host_scan(struct work_struct *work)
 	scsi_scan_host(host);
 }
 
+#if IS_ENABLED(CONFIG_SCSI_FC_ATTRS)
+static int storvsc_user_scan(struct Scsi_Host *host,
+			     unsigned int channel,
+			     unsigned int id,
+			     u64 lun)
+{
+	unsigned int first_channel, last_channel;
+	unsigned int first_id, end_id;
+	unsigned int ch, target;
+
+	if ((channel != SCAN_WILD_CARD && channel > host->max_channel) ||
+	    (id != SCAN_WILD_CARD && id >= host->max_id) ||
+	    (lun != SCAN_WILD_CARD && lun >= host->max_lun))
+		return -EINVAL;
+
+	first_channel = channel == SCAN_WILD_CARD ? 0 : channel;
+	last_channel = channel == SCAN_WILD_CARD ? host->max_channel : channel;
+	first_id = id == SCAN_WILD_CARD ? 0 : id;
+	end_id = id == SCAN_WILD_CARD ? host->max_id : id + 1;
+
+	for (ch = first_channel; ch <= last_channel; ch++) {
+		for (target = first_id; target < end_id; target++)
+			scsi_scan_target(&host->shost_gendev, ch, target, lun,
+					 SCSI_SCAN_MANUAL);
+	}
+
+	return 0;
+}
+#endif
+
 static void storvsc_remove_lun(struct work_struct *work)
 {
 	struct storvsc_scan_work *wrk;
@@ -2232,6 +2262,8 @@ static int __init storvsc_drv_init(void)
 	fc_transport_template = fc_attach_transport(&fc_transport_functions);
 	if (!fc_transport_template)
 		return -ENODEV;
+
+	fc_transport_template->user_scan = storvsc_user_scan;
 #endif
 
 	ret = vmbus_driver_register(&storvsc_drv);
-- 
2.55.0

Re: [PATCH v2] scsi: storvsc: Support manual scans for all Hyper-V targets

[Martin K. Petersen (Oracle)]

Laurence,

> The Fibre Channel transport topology created by storvsc exposes only
> one dummy remote port per SCSI host. Its scsi_target_id is always
> zero.
>
> As a result, the FC transport user-scan path looks up the remote port
> using target ID 0. It cannot initiate a scan for Target 1 or higher.
> No SCSI command is therefore sent to Hyper-V when userspace explicitly
> requests a scan of one of these targets.

Applied to 7.3/scsi-staging, thanks!

-- 
Martin K. Petersen