- gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup.patch removed from -mm tree

- gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup.patch removed from -mm tree

[akpm]

The patch titled
     gpio max7301: check spi_setup() return code, cleanup
has been removed from the -mm tree.  Its filename was
     gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup.patch

This patch was dropped because it was folded into gpio-gpio-driver-for-max7301-spi-gpio-expander.patch

The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/

------------------------------------------------------
Subject: gpio max7301: check spi_setup() return code, cleanup
From: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>

Fix inaccuracies in comments, check spi_setup() return code, mask off high
byte in max7301_read().  Thanks to David Brownell for the review.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---

 drivers/gpio/max7301.c |   15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff -puN drivers/gpio/max7301.c~gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup drivers/gpio/max7301.c
--- a/drivers/gpio/max7301.c~gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup
+++ a/drivers/gpio/max7301.c
@@ -71,7 +71,7 @@ struct max7301 {
  *
  * A write to the MAX7301 means one message with one transfer
  *
- * Returns 0 if successfull or a negative value on error
+ * Returns 0 if successful or a negative value on error
  */
 static int max7301_write(struct spi_device *spi, unsigned int reg, unsigned int val)
 {
@@ -84,9 +84,9 @@ static int max7301_write(struct spi_devi
  * @spi: The SPI device
  * @reg: Register offset
  *
- * A read from the MAX7301 means one message with two transfers
+ * A read from the MAX7301 means two transfers; here, one message each
  *
- * Returns positive 8 bit value from device if successfull or a
+ * Returns positive 8 bit value from device if successful or a
  * negative value on error
  */
 static int max7301_read(struct spi_device *spi, unsigned int reg)
@@ -99,12 +99,13 @@ static int max7301_read(struct spi_devic
 	if (ret)
 		return ret;
 	/*
-	 * FIXME: This read should write 0x0000 (=NOOP at MAX7301 side)
+	 * This relies on the fact, that a transfer with NULL tx_buf shifts out
+	 * zero bytes (=NOOP for MAX7301)
 	 */
 	ret = spi_read(spi, (u8 *)&word, sizeof(word));
 	if (ret)
 		return ret;
-	return word;
+	return word & 0xff;
 }
 
 static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
@@ -224,7 +225,9 @@ static int __devinit max7301_probe(struc
 	 */
 	spi->bits_per_word = 16;
 
-	spi->master->setup(spi);
+	ret = spi_setup(spi);
+	if (ret < 0)
+		return ret;
 
 	ts = kzalloc(sizeof(struct max7301), GFP_KERNEL);
 	if (!ts)
_

Patches currently in -mm which might be from g.liakhovetski@pengutronix.de are

origin.patch
gpio-gpio-driver-for-max7301-spi-gpio-expander.patch
gpio-gpio-driver-for-max7301-spi-gpio-expander-check-spi_setup-return-code-cleanup.patch
linux-next.patch
git-arm.patch
git-dvb.patch
gpio-sysfs-interface-updated.patch
gpio-sysfs-interface-updated-update.patch