Re: [PATCH 3/9] net: dsa: mv88e6xxx: implement get_phy_address

[Vladimir Oltean <olteanv@gmail.com>]

On Tue, Nov 08, 2022 at 09:23:24AM +0100, Lukasz Majewski wrote:
> From: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
> 
> Avoid the need to specify a PHY for each physical port in the device tree
> when phy_base_addr is not 0 (6250 and 6341 families).
> 
> This change should be backwards-compatible with existing device trees,
> as it only adds sensible defaults where explicit definitions were
> required before.
> 
> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>

Needs your Signed-off-by tag as well.

> ---

Would it be possible to do like armada-3720-turris-mox.dts does, and put
the phy-handle in the device tree, avoiding the need for so many PHY
address translation quirks?

If you're going to have U-Boot support for this switch as well, the
phy-handle mechanism is the only thing that U-Boot supports, so device
trees written in this way will work for both (and can be passed by
U-Boot to Linux):

	switch1@11 {
		compatible = "marvell,mv88e6190";
		reg = <0x11>;
		dsa,member = <0 1>;
		interrupt-parent = <&moxtet>;
		interrupts = <MOXTET_IRQ_PERIDOT(1)>;
		status = "disabled";

		mdio {
			#address-cells = <1>;
			#size-cells = <0>;

			switch1phy1: switch1phy1@1 {
				reg = <0x1>;
			};

			switch1phy2: switch1phy2@2 {
				reg = <0x2>;
			};

			switch1phy3: switch1phy3@3 {
				reg = <0x3>;
			};

			switch1phy4: switch1phy4@4 {
				reg = <0x4>;
			};

			switch1phy5: switch1phy5@5 {
				reg = <0x5>;
			};

			switch1phy6: switch1phy6@6 {
				reg = <0x6>;
			};

			switch1phy7: switch1phy7@7 {
				reg = <0x7>;
			};

			switch1phy8: switch1phy8@8 {
				reg = <0x8>;
			};
		};

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@1 {
				reg = <0x1>;
				label = "lan9";
				phy-handle = <&switch1phy1>;
			};

			port@2 {
				reg = <0x2>;
				label = "lan10";
				phy-handle = <&switch1phy2>;
			};

			port@3 {
				reg = <0x3>;
				label = "lan11";
				phy-handle = <&switch1phy3>;
			};

			port@4 {
				reg = <0x4>;
				label = "lan12";
				phy-handle = <&switch1phy4>;
			};

			port@5 {
				reg = <0x5>;
				label = "lan13";
				phy-handle = <&switch1phy5>;
			};

			port@6 {
				reg = <0x6>;
				label = "lan14";
				phy-handle = <&switch1phy6>;
			};

			port@7 {
				reg = <0x7>;
				label = "lan15";
				phy-handle = <&switch1phy7>;
			};

			port@8 {
				reg = <0x8>;
				label = "lan16";
				phy-handle = <&switch1phy8>;
			};

			switch1port9: port@9 {
				reg = <0x9>;
				label = "dsa";
				phy-mode = "2500base-x";
				managed = "in-band-status";
				link = <&switch0port10>;
			};

			switch1port10: port@a {
				reg = <0xa>;
				label = "dsa";
				phy-mode = "2500base-x";
				managed = "in-band-status";
				link = <&switch2port9>;
				status = "disabled";
			};

			port-sfp@a {
				reg = <0xa>;
				label = "sfp";
				sfp = <&sfp>;
				phy-mode = "sgmii";
				managed = "in-band-status";
				status = "disabled";
			};
		};
	};