[PATCH v3 5/5] dt-bindings: net: ipq4019-mdio: Document ipq5332 platform

[Luo Jie <quic_luoj@quicinc.com>]

Update the yaml file for the new DTS properties.

1. cmn-reference-clock for the CMN PLL source clock select.
2. clock-frequency for MDIO clock frequency config.
3. add uniphy AHB & SYS GCC clocks.
4. add reset-gpios for MDIO bus level reset.

Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
---
 .../bindings/net/qcom,ipq4019-mdio.yaml       | 143 +++++++++++++++++-
 1 file changed, 139 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
index 3407e909e8a7..79f8513739e7 100644
--- a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
+++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml
@@ -20,6 +20,8 @@ properties:
           - enum:
               - qcom,ipq6018-mdio
               - qcom,ipq8074-mdio
+              - qcom,ipq9574-mdio
+              - qcom,ipq5332-mdio
           - const: qcom,ipq4019-mdio
 
   "#address-cells":
@@ -30,19 +32,77 @@ properties:
 
   reg:
     minItems: 1
-    maxItems: 2
+    maxItems: 5
     description:
-      the first Address and length of the register set for the MDIO controller.
-      the second Address and length of the register for ethernet LDO, this second
-      address range is only required by the platform IPQ50xx.
+      the first Address and length of the register set for the MDIO controller,
+      the optional second, third and fourth address and length of the register
+      for ethernet LDO, these three address range are required by the platform
+      IPQ50xx/IPQ5332, the last address and length is for the CMN clock to
+      select the reference clock.
+
+  reg-names:
+    minItems: 1
+    maxItems: 5
 
   clocks:
+    minItems: 1
     items:
       - description: MDIO clock source frequency fixed to 100MHZ
+      - description: UNIPHY0 AHB clock source frequency fixed to 100MHZ
+      - description: UNIPHY1 AHB clock source frequency fixed to 100MHZ
+      - description: UNIPHY0 SYS clock source frequency fixed to 24MHZ
+      - description: UNIPHY1 SYS clock source frequency fixed to 24MHZ
 
   clock-names:
+    minItems: 1
     items:
       - const: gcc_mdio_ahb_clk
+      - const: uniphy0_ahb
+      - const: uniphy1_ahb
+      - const: uniphy0_sys
+      - const: uniphy1_sys
+
+  cmn-reference-clock:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    oneOf:
+      - items:
+          - enum:
+              - 0   # CMN PLL reference internal 48MHZ
+              - 1   # CMN PLL reference external 25MHZ
+              - 2   # CMN PLL reference external 31250KHZ
+              - 3   # CMN PLL reference external 40MHZ
+              - 4   # CMN PLL reference external 48MHZ
+              - 5   # CMN PLL reference external 50MHZ
+              - 6   # CMN PLL reference internal 96MHZ
+
+  clock-frequency:
+    oneOf:
+      - items:
+          - enum:
+              - 12500000
+              - 6250000
+              - 3125000
+              - 1562500
+              - 781250
+              - 390625
+    description:
+      The MDIO bus clock that must be output by the MDIO bus hardware,
+      only the listed frequencies above can be supported, other frequency
+      will cause malfunction. If absent, the default hardware value 0xff
+      is used, which means the default MDIO clock frequency 390625HZ, The
+      MDIO clock frequency is MDIO_SYS_CLK/(MDIO_CLK_DIV + 1), the SoC
+      MDIO_SYS_CLK is fixed to 100MHZ, the MDIO_CLK_DIV is from MDIO control
+      register, there is higher clock frequency requirement on the normal
+      working case where the MDIO slave devices support high clock frequency.
+
+  reset-gpios:
+    maxItems: 1
+
+  reset-assert-us:
+    maxItems: 1
+
+  reset-deassert-us:
+    maxItems: 1
 
 required:
   - compatible
@@ -61,6 +121,8 @@ allOf:
               - qcom,ipq5018-mdio
               - qcom,ipq6018-mdio
               - qcom,ipq8074-mdio
+              - qcom,ipq5332-mdio
+              - qcom,ipq9574-mdio
     then:
       required:
         - clocks
@@ -70,6 +132,20 @@ allOf:
         clocks: false
         clock-names: false
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,ipq5332-mdio
+    then:
+      properties:
+        clocks:
+          minItems: 5
+          maxItems: 5
+        reg-names:
+          minItems: 4
+
 unevaluatedProperties: false
 
 examples:
@@ -100,3 +176,62 @@ examples:
         reg = <4>;
       };
     };
+
+  - |
+    #include <dt-bindings/clock/qcom,ipq5332-gcc.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    mdio@90000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "qcom,ipq5332-mdio",
+                   "qcom,ipq4019-mdio";
+      cmn-reference-clock = <0>;
+      clock-frequency = <6250000>;
+
+      reset-gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
+      reset-assert-us = <100000>;
+      reset-deassert-us = <100000>;
+
+      reg = <0x90000 0x64>,
+            <0x9B000 0x800>,
+            <0x7A00610 0x4>,
+            <0x7A10610 0x4>;
+
+      reg-names = "mdio",
+                  "cmn_blk",
+                  "eth_ldo1",
+                  "eth_ldo2";
+
+      clocks = <&gcc GCC_MDIO_AHB_CLK>,
+               <&gcc GCC_UNIPHY0_AHB_CLK>,
+               <&gcc GCC_UNIPHY1_AHB_CLK>,
+               <&gcc GCC_UNIPHY0_SYS_CLK>,
+               <&gcc GCC_UNIPHY1_SYS_CLK>;
+
+      clock-names = "gcc_mdio_ahb_clk",
+                    "uniphy0_ahb",
+                    "uniphy1_ahb",
+                    "uniphy0_sys",
+                    "uniphy1_sys";
+
+      qca8kphy0: ethernet-phy@1 {
+        compatible = "ethernet-phy-id004d.d180";
+        reg = <1>;
+      };
+
+      qca8kphy1: ethernet-phy@2 {
+        compatible = "ethernet-phy-id004d.d180";
+        reg = <2>;
+      };
+
+      qca8kphy2: ethernet-phy@3 {
+        compatible = "ethernet-phy-id004d.d180";
+        reg = <3>;
+      };
+
+      qca8kphy3: ethernet-phy@4 {
+        compatible = "ethernet-phy-id004d.d180";
+        reg = <4>;
+      };
+    };
-- 
2.42.0