[net-next,v2,2/2] net: phy: realtek: Add support for PHY LEDs on RTL8211E

[Michael Klein <michael@fossekall.de>]

Like the RTL8211F, the RTL8211E PHY supports up to three LEDs.
Add netdev trigger support for them, too.

Signed-off-by: Michael Klein <michael@fossekall.de>
---
 drivers/net/phy/realtek/realtek_main.c | 106 +++++++++++++++++++++++--
 1 file changed, 100 insertions(+), 6 deletions(-)

diff --git a/drivers/net/phy/realtek/realtek_main.c b/drivers/net/phy/realtek/realtek_main.c
index abea2291b0f4..ade265cc13f3 100644
--- a/drivers/net/phy/realtek/realtek_main.c
+++ b/drivers/net/phy/realtek/realtek_main.c
@@ -37,6 +37,20 @@
 #define RTL8211E_TX_DELAY			BIT(12)
 #define RTL8211E_RX_DELAY			BIT(11)
 
+#define RTL8211E_LEDCR_EXT_PAGE			0x2c
+
+#define RTL8211E_LEDCR1				0x1a
+#define RTL8211E_LEDCR1_ACT_TXRX		BIT(4)
+#define RTL8211E_LEDCR1_MASK			BIT(4)
+#define RTL8211E_LEDCR1_SHIFT			1
+
+#define RTL8211E_LEDCR2				0x1c
+#define RTL8211E_LEDCR2_LINK_1000		BIT(2)
+#define RTL8211E_LEDCR2_LINK_100		BIT(1)
+#define RTL8211E_LEDCR2_LINK_10			BIT(0)
+#define RTL8211E_LEDCR2_MASK			GENMASK(2, 0)
+#define RTL8211E_LEDCR2_SHIFT			4
+
 #define RTL8211F_PHYCR1				0x18
 #define RTL8211F_PHYCR2				0x19
 #define RTL8211F_INSR				0x1d
@@ -113,7 +127,8 @@
 #define RTL_8221B_VN_CG				0x001cc84a
 #define RTL_8251B				0x001cc862
 
-#define RTL8211F_LED_COUNT			3
+/* RTL8211E and RTL8211F support up to three LEDs */
+#define RTL8211x_LED_COUNT			3
 
 MODULE_DESCRIPTION("Realtek PHY driver");
 MODULE_AUTHOR("Johnson Leung");
@@ -534,7 +549,7 @@ static int rtl821x_resume(struct phy_device *phydev)
 	return 0;
 }
 
-static int rtl8211f_led_hw_is_supported(struct phy_device *phydev, u8 index,
+static int rtl8211x_led_hw_is_supported(struct phy_device *phydev, u8 index,
 					unsigned long rules)
 {
 	const unsigned long mask = BIT(TRIGGER_NETDEV_LINK_10) |
@@ -553,9 +568,11 @@ static int rtl8211f_led_hw_is_supported(struct phy_device *phydev, u8 index,
 	 *      rates and Active indication always at all three 10+100+1000
 	 *      link rates.
 	 * This code currently uses mode B only.
+	 *
+	 * RTL8211E PHY LED has one mode, which works like RTL8211F mode B.
 	 */
 
-	if (index >= RTL8211F_LED_COUNT)
+	if (index >= RTL8211x_LED_COUNT)
 		return -EINVAL;
 
 	/* Filter out any other unsupported triggers. */
@@ -574,7 +591,7 @@ static int rtl8211f_led_hw_control_get(struct phy_device *phydev, u8 index,
 {
 	int val;
 
-	if (index >= RTL8211F_LED_COUNT)
+	if (index >= RTL8211x_LED_COUNT)
 		return -EINVAL;
 
 	val = phy_read_paged(phydev, 0xd04, RTL8211F_LEDCR);
@@ -607,7 +624,7 @@ static int rtl8211f_led_hw_control_set(struct phy_device *phydev, u8 index,
 	const u16 mask = RTL8211F_LEDCR_MASK << (RTL8211F_LEDCR_SHIFT * index);
 	u16 reg = 0;
 
-	if (index >= RTL8211F_LED_COUNT)
+	if (index >= RTL8211x_LED_COUNT)
 		return -EINVAL;
 
 	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
@@ -630,6 +647,80 @@ static int rtl8211f_led_hw_control_set(struct phy_device *phydev, u8 index,
 	return phy_modify_paged(phydev, 0xd04, RTL8211F_LEDCR, mask, reg);
 }
 
+static int rtl8211e_led_hw_control_get(struct phy_device *phydev, u8 index,
+				       unsigned long *rules)
+{
+	int ret;
+	u16 cr1, cr2;
+
+	if (index >= RTL8211x_LED_COUNT)
+		return -EINVAL;
+
+	ret = rtl8211e_read_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE, RTL8211E_LEDCR1);
+	if (ret < 0)
+		return ret;
+
+	cr1 = ret >> RTL8211E_LEDCR1_SHIFT * index;
+	if (cr1 & RTL8211E_LEDCR1_ACT_TXRX) {
+		set_bit(TRIGGER_NETDEV_RX, rules);
+		set_bit(TRIGGER_NETDEV_TX, rules);
+	}
+
+	ret = rtl8211e_read_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE, RTL8211E_LEDCR2);
+	if (ret < 0)
+		return ret;
+
+	cr2 = ret >> RTL8211E_LEDCR2_SHIFT * index;
+	if (cr2 & RTL8211E_LEDCR2_LINK_10)
+		set_bit(TRIGGER_NETDEV_LINK_10, rules);
+
+	if (cr2 & RTL8211E_LEDCR2_LINK_100)
+		set_bit(TRIGGER_NETDEV_LINK_100, rules);
+
+	if (cr2 & RTL8211E_LEDCR2_LINK_1000)
+		set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+
+	return ret;
+}
+
+static int rtl8211e_led_hw_control_set(struct phy_device *phydev, u8 index,
+				       unsigned long rules)
+{
+	const u16 cr1mask = RTL8211E_LEDCR1_MASK << (RTL8211E_LEDCR1_SHIFT * index);
+	const u16 cr2mask = RTL8211E_LEDCR2_MASK << (RTL8211E_LEDCR2_SHIFT * index);
+	u16 cr1 = 0, cr2 = 0;
+	int ret;
+
+	if (index >= RTL8211x_LED_COUNT)
+		return -EINVAL;
+
+	if (test_bit(TRIGGER_NETDEV_RX, &rules) ||
+	    test_bit(TRIGGER_NETDEV_TX, &rules)) {
+		cr1 |= RTL8211E_LEDCR1_ACT_TXRX;
+	}
+
+	cr1 <<= RTL8211E_LEDCR1_SHIFT * index;
+	ret = rtl8211e_modify_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE,
+				       RTL8211E_LEDCR1, cr1mask, cr1);
+	if (ret < 0)
+		return ret;
+
+	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+		cr2 |= RTL8211E_LEDCR2_LINK_10;
+
+	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+		cr2 |= RTL8211E_LEDCR2_LINK_100;
+
+	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+		cr2 |= RTL8211E_LEDCR2_LINK_1000;
+
+	cr2 <<= RTL8211E_LEDCR2_SHIFT * index;
+	ret = rtl8211e_modify_ext_page(phydev, RTL8211E_LEDCR_EXT_PAGE,
+				       RTL8211E_LEDCR2, cr2mask, cr2);
+
+	return ret;
+}
+
 static int rtl8211e_config_init(struct phy_device *phydev)
 {
 	const u16 delay_mask = RTL8211E_CTRL_DELAY |
@@ -1405,6 +1496,9 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= genphy_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.led_hw_is_supported = rtl8211x_led_hw_is_supported,
+		.led_hw_control_get = rtl8211e_led_hw_control_get,
+		.led_hw_control_set = rtl8211e_led_hw_control_set,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc916),
 		.name		= "RTL8211F Gigabit Ethernet",
@@ -1418,7 +1512,7 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
 		.flags		= PHY_ALWAYS_CALL_SUSPEND,
-		.led_hw_is_supported = rtl8211f_led_hw_is_supported,
+		.led_hw_is_supported = rtl8211x_led_hw_is_supported,
 		.led_hw_control_get = rtl8211f_led_hw_control_get,
 		.led_hw_control_set = rtl8211f_led_hw_control_set,
 	}, {
-- 
2.39.5