From: Tony Nguyen <anthony.l.nguyen@intel.com>
To: davem@davemloft.net, kuba@kernel.org, pabeni@redhat.com,
edumazet@kernel.org, andrew+netdev@lunn.ch,
netdev@vger.kernel.org
Cc: Jacob Keller <jacob.e.keller@intel.com>,
anthony.l.nguyen@intel.com, maciej.machnikowski@intel.com,
przemyslaw.korba@intel.com, grzegorz.nitka@intel.com,
sergey.temerkhanov@intel.com, arkadiusz.kubalewski@intel.com,
poros@redhat.com, richardcochran@gmail.com, horms@kernel.org
Subject: [PATCH net v3 13/14] ice: skip reading Tx ready bitmap on ports with no timestamps
Date: Thu, 15 Oct 2026 12:10:59 -0700 [thread overview]
Message-ID: <20261015191102.1174111-14-anthony.l.nguyen@intel.com> (raw)
In-Reply-To: <20261015191102.1174111-1-anthony.l.nguyen@intel.com>
From: Jacob Keller <jacob.e.keller@intel.com>
On E82x devices, the interrupt for Tx timestamps are handled by the clock
owner. When an interrupt with the Tx timestamp cause is fired, the clock
owner PF iterates the list of ports and checks for timestamps across all
ports.
The existing logic reads the PHY timestamp ready bitmap before iterating
the list of in-use timestamp indexes, even for ports which have no
timestamps waiting in the software timestamp tracker. This has a
significant and measurable latency impact on reporting Tx timestamps.
Check the bitmap and exit early in the event that there are no timestamps
waiting on a port. Observant reviewers may notice that the check is done
without acquiring the lock. This is fine, as whether the thread sees or
fails to see a new outstanding timestamp does not affect correctness, only
determining whether or not it should do extra work.
Skipping the check has the highest impact on E822 an E825 devices which
iterate all ports in a single thread, but it is applied universally to all
device types since the extra read is unnecessary regardless.
The average latency of a Tx timestamp is impacted by several factors
including system load, the number of timestamp requests, and some random
factors that are difficult to control. However for comparison on my system
with these changes, while operating ptp4l on a single port with a sync rate
of 16/second:
Before: mean 317.43 microseconds, standard deviation 34.51
After: mean 189.71 microseconds, standard deviation 43.24
Of course this level of improvement may not be indicative of a production
setup as one might expect timestamps to be operating out of multiple ports
on the device. However, even in that case an improvement is still likely
depending on the actual timestamp rates.
Fixes: d938a8cca88a ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
drivers/net/ethernet/intel/ice/ice_ptp.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/intel/ice/ice_ptp.c b/drivers/net/ethernet/intel/ice/ice_ptp.c
index 57141e94c570..a9658f859c2e 100644
--- a/drivers/net/ethernet/intel/ice/ice_ptp.c
+++ b/drivers/net/ethernet/intel/ice/ice_ptp.c
@@ -574,7 +574,7 @@ static void ice_ptp_process_tx_tstamp(struct ice_ptp_tx *tx)
pf = ptp_port_to_pf(ptp_port);
hw = &pf->hw;
- if (!tx->init)
+ if (!tx->init || bitmap_empty(tx->in_use, tx->len))
return;
/* Read the Tx ready status first */
--
2.47.1
next prev parent reply other threads:[~2026-10-15 19:11 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-15 19:10 [PATCH net v3 00/14][pull request] ice: E82x: timestamp processing logic fixes Tony Nguyen
2026-10-15 19:10 ` [PATCH net v3 01/14] ice: fix removal of PTP timestamp tracker during reset Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:14 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 02/14] ice: use reference counting and SRCU for PTP port access Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:16 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 03/14] ice: fix PHY port restart serialization Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:21 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 04/14] ice: set in_use only after preparing Tx timestamp index Tony Nguyen
2026-10-15 19:10 ` [PATCH net v3 05/14] ice: call PTP link change only from link events Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:35 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 06/14] ice: E822: keep Tx timestamps disabled during offset calibration Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:37 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 07/14] ice: E822: cancel offset verification work during reset preparation Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:40 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 08/14] ice: E825: stop clearing PHY_REG_TX_OFFSET_READY Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:42 ` Jacob Keller
2026-10-20 1:53 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 09/14] ice: E825: clear PHY_TSTAMP memory prior to soft reset Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:49 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 10/14] ice: E825: perform a soft reset when starting the PHY timer Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-19 23:57 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 11/14] ice: wait for in-flight Tx timestamps before removing the tracker Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-20 0:05 ` Jacob Keller
2026-10-15 19:10 ` [PATCH net v3 12/14] ice: keep Tx timestamp slots tracked until completion or timeout Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-20 0:11 ` Jacob Keller
2026-10-15 19:10 ` Tony Nguyen [this message]
2026-10-15 19:11 ` [PATCH net v3 14/14] ice: don't clear in_use until HW clears ready bitmap Tony Nguyen
2026-10-19 20:14 ` netdev-bot+sashiko
2026-10-20 0:18 ` Jacob Keller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261015191102.1174111-14-anthony.l.nguyen@intel.com \
--to=anthony.l.nguyen@intel.com \
--cc=andrew+netdev@lunn.ch \
--cc=arkadiusz.kubalewski@intel.com \
--cc=davem@davemloft.net \
--cc=edumazet@kernel.org \
--cc=grzegorz.nitka@intel.com \
--cc=horms@kernel.org \
--cc=jacob.e.keller@intel.com \
--cc=kuba@kernel.org \
--cc=maciej.machnikowski@intel.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=poros@redhat.com \
--cc=przemyslaw.korba@intel.com \
--cc=richardcochran@gmail.com \
--cc=sergey.temerkhanov@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox