From: Florian Fainelli <f.fainelli@gmail.com>
To: netdev-bot+sashiko@kernel.org
Cc: netdev@vger.kernel.org, andrew+netdev@lunn.ch,
davem@davemloft.net, edumazet@kernel.org, kuba@kernel.org,
pabeni@redhat.com, hkallweit1@gmail.com, linux@armlinux.org.uk,
shaojijie@huawei.com, horms@kernel.org, runyu.xiao@seu.edu.cn,
mmyangfl@gmail.com, hvr@gnu.org, danny.kukawka@bisect.de,
mugunthanvnm@ti.com, sebastian.hesselbarth@gmail.com,
linux-kernel@vger.kernel.org, manuel.lauss@gmail.com
Subject: Re: [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus
Date: Fri, 20 Nov 2026 15:58:27 -0800 [thread overview]
Message-ID: <2ed2823f-298a-49e0-98d7-58545f09b304@gmail.com> (raw)
In-Reply-To: <179517075464.3136.12005891937960917967@kernel.org>
On 11/20/26 02:32, netdev-bot+sashiko@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found more severe
> issue(s) in other patches of this series. This mail is only an FYI, in case
> you want to address the nit picks below when you respin.
>
> Low priority / nit picks for your consideration:
>
> - [Low] The commit message of "net: au1000: disconnect the PHY before
> freeing the MDIO bus" partly misstates what the patch fixes, and…
>
> --
>
> net: au1000: disconnect the PHY before freeing the MDIO bus
>
> This commit adds phy_disconnect() calls to the au1000_probe() error path
> and to au1000_remove(), so that phy_connect() is balanced. It also makes
> au1000_reset_mac_unlocked() skip MAC control register accesses when
> mac_enabled is clear. It also resets the MAC in au1000_remove() after the
> PHY and MDIO bus are torn down.
>
>> Balance phy_connect() on probe failure and removal. Otherwise PHY
>> interrupts, device references and the attachment to the freed netdev
>> survive teardown.
>
> [Severity: Low]
> Can a PHY interrupt actually survive teardown in this driver?
>
> mdiobus_alloc_size() sets every bus->irq[i] to PHY_POLL. au1000_probe()
> only writes a real IRQ into mii_bus->irq[] when aup->phy_static_config is
> set:
>
> if (aup->phy_static_config)
> if (aup->phy_irq && aup->phy_busid == aup->mac_id)
> aup->mii_bus->irq[aup->phy_addr] = aup->phy_irq;
>
> In that same case, au1000_mii_probe() returns before it reaches
> phy_connect():
>
> if (aup->phy_static_config) {
> ...
> if (aup->phy_addr)
> phydev = mdiobus_get_phy(aup->mii_bus, aup->phy_addr);
> else
> netdev_info(dev, "using PHY-less setup\n");
> return 0;
> }
>
> That leaves dev->phydev NULL, so the new phy_disconnect() calls are
> skipped.
>
> On the dynamic search path, which is the only one that calls
> phy_connect(), the PHY's irq is still PHY_POLL. That means no interrupt
> is ever requested, and phy_disconnect() never reaches
> phy_free_interrupt().
>
> The device and module references taken in phy_attach_direct(), and the
> attached_dev pointer to the freed netdev, do look like real leaks. Should
> the "PHY interrupts" part be dropped from the message?
>
>> PHY teardown can re-enable the MAC for MDIO even if the interface was
>> never opened. Reset the MAC after PHY and MDIO bus teardown, before
>> releasing descriptors and register mappings. Skip MAC control accesses
>> when mac_enabled is clear, since stopping an already clock-gated MAC
>> hangs MTX-1.
>
> Would it help to say that the new mac_enabled check also fixes an
> existing hang when register_netdev() fails in au1000_probe()?
>
> Before this patch, the au1000_reset_mac() call just before
> register_netdev() gated the MAC clock and cleared mac_enabled. If
> register_netdev() then failed, the err_out path called
> mdiobus_unregister(), which does no MDIO access, and then called
> au1000_reset_mac() again:
>
> au1000_probe()
> au1000_reset_mac(dev); <- clock gated, mac_enabled = 0
> register_netdev(dev) fails
> goto err_out
> mdiobus_unregister()
> au1000_reset_mac(dev)
> au1000_hard_stop(dev)
> readl(&aup->mac->control) <- MAC already clock-gated
>
> According to the commit message, this access hangs MTX-1. The message
> describes the PHY teardown case but not this change in the
> register_netdev() failure path. Mentioning it would show backporters
> which failure modes this patch fixes.
>
Agreed on both points. I have updated the commit message to remove the
PHY-interrupt claim: the path that calls phy_connect() uses polling. The
message now describes the leaked device/module references and the stale
attached_dev pointer.
I also added the existing register_netdev() failure case. Probe gates
the MAC clock before registration, and the error unwind resets it again.
The mac_enabled guard prevents that second reset from accessing
clock-gated MAC control registers if no intervening MDIO access has
re-enabled the MAC.
This is a commit-message-only revision; the code is unchanged. The
registration-failure path was verified by source inspection, not fault
injection.
pw-bot: cr
--
Florian
next prev parent reply other threads:[~2026-11-20 23:58 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-17 19:32 [PATCH net v3 00/10] net: au1000: Bug fixes Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 01/10] net: au1000: recycle RX descriptors on allocation failure Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 02/10] net: au1000: clear all-multicast mode when restoring hash filtering Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 03/10] net: au1000: disconnect the PHY before freeing the MDIO bus Florian Fainelli
2026-11-20 10:32 ` netdev-bot+sashiko
2026-11-20 23:58 ` Florian Fainelli [this message]
2026-11-17 19:32 ` [PATCH net v3 04/10] net: au1000: report MDIO transaction timeouts Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 05/10] net: au1000: serialize TX completion with packet submission Florian Fainelli
2026-11-20 10:32 ` netdev-bot+sashiko
2026-11-21 0:06 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 06/10] net: au1000: restore receive filtering before enabling RX Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 07/10] net: au1000: restore RX buffer addresses when restarting the MAC Florian Fainelli
2026-11-20 10:32 ` netdev-bot+sashiko
2026-11-21 0:22 ` Florian Fainelli
2026-11-17 19:32 ` [PATCH net v3 08/10] net: phy: smsc: wait for LAN83C183 power-down recovery Florian Fainelli
2026-11-20 10:32 ` netdev-bot+sashiko
2026-11-17 19:32 ` [PATCH net v3 09/10] net: au1000: keep the MAC stopped until the PHY link is ready Florian Fainelli
2026-11-20 10:32 ` netdev-bot+sashiko
2026-11-17 19:32 ` [PATCH net v3 10/10] net: au1000: reject frames larger than the TX bounce buffer Florian Fainelli
2026-11-17 19:38 ` [PATCH net v3 00/10] net: au1000: Bug fixes netdev-bot+sinfo
2026-11-17 21:54 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2ed2823f-298a-49e0-98d7-58545f09b304@gmail.com \
--to=f.fainelli@gmail.com \
--cc=andrew+netdev@lunn.ch \
--cc=danny.kukawka@bisect.de \
--cc=davem@davemloft.net \
--cc=edumazet@kernel.org \
--cc=hkallweit1@gmail.com \
--cc=horms@kernel.org \
--cc=hvr@gnu.org \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=manuel.lauss@gmail.com \
--cc=mmyangfl@gmail.com \
--cc=mugunthanvnm@ti.com \
--cc=netdev-bot+sashiko@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=runyu.xiao@seu.edu.cn \
--cc=sebastian.hesselbarth@gmail.com \
--cc=shaojijie@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox