* Re: NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX [not found] <20060405175033.GE16850@bayes.mathematik.tu-chemnitz.de> @ 2006-05-23 13:36 ` Marco Berizzi 2006-05-23 20:58 ` Steffen Klassert 0 siblings, 1 reply; 5+ messages in thread From: Marco Berizzi @ 2006-05-23 13:36 UTC (permalink / raw) To: klassert; +Cc: netdev Steffen Klassert wrote: >On Wed, Apr 05, 2006 at 06:33:18PM +0200, Marco Berizzi wrote: > > Hello everybody. > > I'm getting these errors (with packet/connectivity loss) on > > our firewall after I have plugged in a 3c905C nic. Linux is > > Slackware 10.2 with vanilla 2.6.16.1. > > > > Hints? > > > > PS: I have temporary resolved the problem running 'ifconfig > > eth2 down' and 'ifconfig eth2 up' > > > > Apr 5 17:47:07 Teti kernel: eth2: Resetting the Tx ring pointer. > > Apr 5 17:47:47 Teti last message repeated 4 times > > Apr 5 17:48:57 Teti last message repeated 7 times > > Apr 5 17:49:57 Teti last message repeated 6 times > > Apr 5 17:50:57 Teti last message repeated 6 times > > > > Apr 5 17:47:07 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed out > >There were some problems of this kind with 10base2 networks in 2.6.16. >Could you please try whether 2.6.17-rc1 has this problems too? [Sorry for the very huge delay, but after 2.6.17-rc1 upgrade xfs filesystem crashed]. Same problem here with 2.6.17-rc3-git18. Running ifconfig eth2 down and ifconfig eth2 up resolves the problem for a while. Here is lspci -v and dmesg root@Teti:/var/log# lspci -v 00:00.0 Host bridge: Intel Corporation 82810E DC-133 GMCH [Graphics Memory Controller Hub] (rev 03) Flags: bus master, fast devsel, latency 0 00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 CGC [Chipset Graphics Controller] (rev 03) (prog-if 00 [VGA]) Subsystem: Siemens Nixdorf AG: Unknown device 004a Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 10 Memory at f8000000 (32-bit, prefetchable) [size=64M] Memory at f4000000 (32-bit, non-prefetchable) [size=512K] Expansion ROM at <unassigned> [disabled] Capabilities: [dc] Power Management version 1 00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=80 I/O behind bridge: 00002000-00002fff Memory behind bridge: f4100000-f41fffff Prefetchable memory behind bridge: 20000000-200fffff 00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02) Flags: bus master, medium devsel, latency 0 00:1f.1 IDE interface: Intel Corporation 82801AA IDE (rev 02) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801AA IDE Flags: bus master, medium devsel, latency 0 I/O ports at 1000 [size=16] 00:1f.2 USB Controller: Intel Corporation 82801AA USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801AA USB Flags: bus master, medium devsel, latency 0, IRQ 9 I/O ports at 1400 [size=32] 00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02) Subsystem: Intel Corporation 82801AA SMBus Flags: medium devsel, IRQ 11 I/O ports at 1800 [size=16] 01:05.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10) Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter Flags: bus master, medium devsel, latency 64, IRQ 10 I/O ports at 2000 [size=256] Memory at f4100000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 1 01:07.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10) Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter Flags: bus master, medium devsel, latency 64, IRQ 11 I/O ports at 2400 [size=256] Memory at f4100400 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:09.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC Flags: bus master, medium devsel, latency 80, IRQ 7 I/O ports at 2800 [size=128] Memory at f4100800 (32-bit, non-prefetchable) [size=128] Expansion ROM at 20000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Linux version 2.6.17-rc3-git18 (root@Teti) (gcc version 3.3.6) #1 Thu May 11 11:15:45 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e6800 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000017ef0000 (usable) BIOS-e820: 0000000017ef0000 - 0000000017effc00 (ACPI data) BIOS-e820: 0000000017effc00 - 0000000017f00000 (ACPI NVS) BIOS-e820: 0000000017f00000 - 0000000018000000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 382MB LOWMEM available. On node 0 totalpages: 98032 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 93936 pages, LIFO batch:31 DMI 2.3 present. Allocating PCI resources starting at 20000000 (gap: 18000000:e7f00000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=301 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (012ff000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 598.119 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 385552k/392128k available (1743k kernel code, 6016k reserved, 480k data, 136k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1197.89 BogoMIPS (lpj=2395797) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 CPU: Intel Pentium III (Coppermine) stepping 03 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd99e, last bus=1 Setting up standard PCI resources PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:01.0 PCI quirk: region f000-f07f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region f180-f1bf claimed by ICH4 GPIO PCI: Transparent bridge - 0000:00:1e.0 PCI: Using IRQ router PIIX/ICH [8086/2410] at 0000:00:1f.0 PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.0 PCI: Bridge: 0000:00:1e.0 IO window: 2000-2fff MEM window: f4100000-f41fffff PREFETCH window: 20000000-200fffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered SGI XFS with no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler deadline registered (default) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH: IDE controller at PCI slot 0000:00:1f.1 ICH: chipset revision 2 ICH: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: ST320413A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: SAMSUNG CD-ROM SC-148F, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: Host Protected Area detected. current capacity is 39102336 sectors (20020 MB) native capacity is 39102337 sectors (20020 MB) hda: Host Protected Area disabled. hda: 39102337 sectors (20020 MB) w/1024KiB Cache, CHS=38792/16/63, UDMA(66) hda: cache flushes not supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 > serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice ip_conntrack version 2.4 (3063 buckets, 24504 max) - 224 bytes per conntrack input: AT Translated Set 2 keyboard as /class/input/input0 ip_tables: (C) 2000-2006 Netfilter Core Team TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI Shortcut mode XFS mounting filesystem hda1 Ending clean XFS mount for filesystem: hda1 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 136k freed Adding 674688k swap on /dev/hda9. Priority:-1 extents:1 across:674688k Filesystem "hda1": Disabling barriers, not supported by the underlying device Filesystem "hda1": Disabling barriers, not supported by the underlying device 8139too Fast Ethernet driver 0.9.27 PCI: Found IRQ 10 for device 0000:01:05.0 PCI: Sharing IRQ 10 with 0000:00:01.0 eth0: RealTek RTL8139 at 0xd8864000, 00:10:b5:51:7c:40, IRQ 10 eth0: Identified 8139 chip type 'RTL-8139A' PCI: Found IRQ 11 for device 0000:01:07.0 PCI: Sharing IRQ 11 with 0000:00:1f.3 eth1: RealTek RTL8139 at 0xd8866400, 00:10:b5:4a:e2:52, IRQ 11 eth1: Identified 8139 chip type 'RTL-8139B' PCI: Found IRQ 7 for device 0000:01:09.0 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:01:09.0: 3Com PCI 3c905C Tornado at d8868800. Filesystem "hda5": Disabling barriers, not supported by the underlying device XFS mounting filesystem hda5 Ending clean XFS mount for filesystem: hda5 Filesystem "hda6": Disabling barriers, not supported by the underlying device XFS mounting filesystem hda6 Ending clean XFS mount for filesystem: hda6 Filesystem "hda7": Disabling barriers, not supported by the underlying device XFS mounting filesystem hda7 Ending clean XFS mount for filesystem: hda7 Filesystem "hda8": Disabling barriers, not supported by the underlying device XFS mounting filesystem hda8 Ending clean XFS mount for filesystem: hda8 May 23 15:07:25 Teti kernel: eth2: Resetting the Tx ring pointer. May 23 15:08:05 Teti last message repeated 4 times May 23 15:09:15 Teti last message repeated 7 times May 23 15:10:15 Teti last message repeated 6 times May 23 15:11:15 Teti last message repeated 6 times This is also my .config # # Automatically generated make config: don't edit # Linux kernel version: 2.6.17-rc3-git18 # Thu May 11 10:55:18 2006 # CONFIG_X86_32=y CONFIG_SEMAPHORE_SLEEPERS=y CONFIG_X86=y CONFIG_MMU=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_DMI=y # # Code maturity level options # # CONFIG_EXPERIMENTAL is not set CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set # CONFIG_RELAY is not set CONFIG_INITRAMFS_SOURCE="" CONFIG_UID16=y CONFIG_VM86=y # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_SLAB=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # CONFIG_SLOB is not set # # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set # CONFIG_KMOD is not set # # Block layer # # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # # IO Schedulers # CONFIG_IOSCHED_NOOP=y # CONFIG_IOSCHED_AS is not set CONFIG_IOSCHED_DEADLINE=y # CONFIG_IOSCHED_CFQ is not set # CONFIG_DEFAULT_AS is not set CONFIG_DEFAULT_DEADLINE=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="deadline" # # Processor type and features # # CONFIG_SMP is not set CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set # CONFIG_MPENTIUMII is not set CONFIG_MPENTIUMIII=y # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set # CONFIG_MK8 is not set # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MGEODE_LX is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=5 CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_TSC=y # CONFIG_HPET_TIMER is not set CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_X86_UP_APIC=y CONFIG_X86_UP_IOAPIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y # CONFIG_X86_MCE is not set # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set # CONFIG_X86_REBOOTFIXUPS is not set # CONFIG_MICROCODE is not set # CONFIG_X86_MSR is not set # CONFIG_X86_CPUID is not set # # Firmware Drivers # # CONFIG_DELL_RBU is not set # CONFIG_DCDBAS is not set CONFIG_NOHIGHMEM=y # CONFIG_HIGHMEM4G is not set # CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000 CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_MATH_EMULATION is not set # CONFIG_MTRR is not set CONFIG_REGPARM=y CONFIG_SECCOMP=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_1000 is not set CONFIG_HZ=250 CONFIG_PHYSICAL_START=0x100000 # # Power management options (ACPI, APM) # # CONFIG_PM is not set # # ACPI (Advanced Configuration and Power Interface) Support # # CONFIG_ACPI is not set # # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set # # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y # CONFIG_PCIEPORTBUS is not set # CONFIG_PCI_MSI is not set CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set # # PCCARD (PCMCIA/CardBus) support # # CONFIG_PCCARD is not set # # PCI Hotplug Support # # # Executable file formats # CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_AOUT is not set # CONFIG_BINFMT_MISC is not set # # Networking # CONFIG_NET=y # # Networking options # # CONFIG_NETDEBUG is not set CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y CONFIG_XFRM=y CONFIG_XFRM_USER=y CONFIG_NET_KEY=y CONFIG_INET=y # CONFIG_IP_MULTICAST is not set CONFIG_IP_ADVANCED_ROUTER=y CONFIG_ASK_IP_FIB_HASH=y # CONFIG_IP_FIB_TRIE is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_FWMARK=y CONFIG_IP_ROUTE_MULTIPATH=y # CONFIG_IP_ROUTE_MULTIPATH_CACHED is not set CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set CONFIG_SYN_COOKIES=y # CONFIG_INET_AH is not set CONFIG_INET_ESP=y CONFIG_INET_IPCOMP=y CONFIG_INET_XFRM_TUNNEL=y CONFIG_INET_TUNNEL=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # # IP: Virtual Server Configuration # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set # CONFIG_INET6_XFRM_TUNNEL is not set # CONFIG_INET6_TUNNEL is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set # # Core Netfilter Configuration # CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m CONFIG_NETFILTER_XTABLES=y CONFIG_NETFILTER_XT_TARGET_CLASSIFY=y CONFIG_NETFILTER_XT_TARGET_CONNMARK=y CONFIG_NETFILTER_XT_TARGET_MARK=y CONFIG_NETFILTER_XT_TARGET_NFQUEUE=y CONFIG_NETFILTER_XT_TARGET_NOTRACK=y CONFIG_NETFILTER_XT_MATCH_COMMENT=y CONFIG_NETFILTER_XT_MATCH_CONNBYTES=y CONFIG_NETFILTER_XT_MATCH_CONNMARK=y CONFIG_NETFILTER_XT_MATCH_CONNTRACK=y CONFIG_NETFILTER_XT_MATCH_DCCP=y CONFIG_NETFILTER_XT_MATCH_ESP=y CONFIG_NETFILTER_XT_MATCH_HELPER=y CONFIG_NETFILTER_XT_MATCH_LENGTH=y CONFIG_NETFILTER_XT_MATCH_LIMIT=y CONFIG_NETFILTER_XT_MATCH_MAC=y CONFIG_NETFILTER_XT_MATCH_MARK=y CONFIG_NETFILTER_XT_MATCH_POLICY=y CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y CONFIG_NETFILTER_XT_MATCH_PKTTYPE=y CONFIG_NETFILTER_XT_MATCH_REALM=y CONFIG_NETFILTER_XT_MATCH_SCTP=y CONFIG_NETFILTER_XT_MATCH_STATE=y CONFIG_NETFILTER_XT_MATCH_STRING=y CONFIG_NETFILTER_XT_MATCH_TCPMSS=y # # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=y CONFIG_IP_NF_CT_ACCT=y CONFIG_IP_NF_CONNTRACK_MARK=y CONFIG_IP_NF_FTP=m # CONFIG_IP_NF_IRC is not set CONFIG_IP_NF_TFTP=m # CONFIG_IP_NF_AMANDA is not set CONFIG_IP_NF_PPTP=m CONFIG_IP_NF_H323=m # CONFIG_IP_NF_QUEUE is not set CONFIG_IP_NF_IPTABLES=y CONFIG_IP_NF_MATCH_IPRANGE=y CONFIG_IP_NF_MATCH_TOS=y # CONFIG_IP_NF_MATCH_RECENT is not set CONFIG_IP_NF_MATCH_ECN=y CONFIG_IP_NF_MATCH_DSCP=y # CONFIG_IP_NF_MATCH_AH is not set CONFIG_IP_NF_MATCH_TTL=y CONFIG_IP_NF_MATCH_OWNER=y CONFIG_IP_NF_MATCH_ADDRTYPE=y CONFIG_IP_NF_MATCH_HASHLIMIT=y CONFIG_IP_NF_FILTER=y CONFIG_IP_NF_TARGET_REJECT=y CONFIG_IP_NF_TARGET_LOG=y # CONFIG_IP_NF_TARGET_ULOG is not set CONFIG_IP_NF_TARGET_TCPMSS=y CONFIG_IP_NF_NAT=y CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=y CONFIG_IP_NF_TARGET_REDIRECT=y CONFIG_IP_NF_TARGET_NETMAP=y CONFIG_IP_NF_TARGET_SAME=y CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_PPTP=m CONFIG_IP_NF_NAT_H323=m CONFIG_IP_NF_MANGLE=y CONFIG_IP_NF_TARGET_TOS=y CONFIG_IP_NF_TARGET_ECN=y CONFIG_IP_NF_TARGET_DSCP=y CONFIG_IP_NF_TARGET_TTL=y CONFIG_IP_NF_RAW=y CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # # QoS and/or fair queueing # # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_IEEE80211 is not set # # Device Drivers # # # Generic Driver Options # CONFIG_STANDALONE=y # CONFIG_PREVENT_FIRMWARE_BUILD is not set # CONFIG_FW_LOADER is not set # # Connector - unified userspace <-> kernelspace linker # # CONFIG_CONNECTOR is not set # # Memory Technology Devices (MTD) # # CONFIG_MTD is not set # # Parallel port support # # CONFIG_PARPORT is not set # # Plug and Play support # # # Block devices # CONFIG_BLK_DEV_FD=m # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_COW_COMMON is not set # CONFIG_BLK_DEV_LOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set # CONFIG_BLK_DEV_INITRD is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y # CONFIG_IDEDISK_MULTI_MODE is not set CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDEFLOPPY is not set # CONFIG_IDE_TASK_IOCTL is not set # # IDE chipset support/bugfixes # # CONFIG_IDE_GENERIC is not set # CONFIG_BLK_DEV_CMD640 is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set # CONFIG_BLK_DEV_GENERIC is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y CONFIG_IDEDMA_ONLYDISK=y # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_ATIIXP is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_CS5535 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_SC1200 is not set CONFIG_BLK_DEV_PIIX=y # CONFIG_BLK_DEV_IT821X is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_PDC202XX_OLD is not set # CONFIG_BLK_DEV_PDC202XX_NEW is not set # CONFIG_BLK_DEV_SVWKS is not set # CONFIG_BLK_DEV_SIIMAGE is not set # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set # CONFIG_BLK_DEV_VIA82CXXX is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set # CONFIG_SCSI is not set # # Multi-device support (RAID and LVM) # # CONFIG_MD is not set # # Fusion MPT device support # # CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support # # CONFIG_IEEE1394 is not set # # I2O device support # # CONFIG_I2O is not set # # Network device support # CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # # ARCnet devices # # CONFIG_ARCNET is not set # # PHY device support # # CONFIG_PHYLIB is not set # # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=m # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_CASSINI is not set CONFIG_NET_VENDOR_3COM=y CONFIG_VORTEX=m CONFIG_TYPHOON=m # # Tulip family network device support # # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_FORCEDETH is not set # CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=m # CONFIG_FEALNX is not set CONFIG_NATSEMI=m # CONFIG_NE2K_PCI is not set CONFIG_8139TOO=m # CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set # CONFIG_8139TOO_8129 is not set # CONFIG_8139_OLD_RX_RESET is not set CONFIG_SIS900=m CONFIG_EPIC100=m # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set CONFIG_VIA_RHINE=m # CONFIG_VIA_RHINE_MMIO is not set # # Ethernet (1000 Mbit) # # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set # # Ethernet (10000 Mbit) # # CONFIG_CHELSIO_T1 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # # Token Ring devices # # CONFIG_TR is not set # # Wireless LAN (non-hamradio) # # CONFIG_NET_RADIO is not set # # Wan interfaces # # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # # ISDN subsystem # # CONFIG_ISDN is not set # # Telephony Support # # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y # CONFIG_SERIO_SERPORT is not set # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y # CONFIG_SERIO_RAW is not set # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # # CONFIG_SERIAL_8250 is not set # # Non-8250 serial port support # # CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # # IPMI # # CONFIG_IPMI_HANDLER is not set # # Watchdog Cards # # CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_RTC is not set # CONFIG_GEN_RTC is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # # Ftape, the floppy tape device driver # # CONFIG_FTAPE is not set # CONFIG_AGP is not set # CONFIG_DRM is not set # CONFIG_MWAVE is not set # CONFIG_CS5535_GPIO is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HANGCHECK_TIMER is not set # # TPM devices # # # I2C support # # CONFIG_I2C is not set # # SPI support # # CONFIG_SPI is not set # CONFIG_SPI_MASTER is not set # # Dallas's 1-wire bus # # CONFIG_W1 is not set # # Hardware Monitoring support # # CONFIG_HWMON is not set # CONFIG_HWMON_VID is not set # # Misc devices # # # Multimedia devices # # CONFIG_VIDEO_DEV is not set # # Digital Video Broadcasting Devices # # CONFIG_DVB is not set # # Graphics support # # CONFIG_FB is not set # CONFIG_VIDEO_SELECT is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y # # Sound # # CONFIG_SOUND is not set # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # # USB Gadget Support # # CONFIG_USB_GADGET is not set # # MMC/SD Card support # # CONFIG_MMC is not set # # LED devices # # CONFIG_NEW_LEDS is not set # # LED drivers # # # LED Triggers # # # InfiniBand support # # CONFIG_INFINIBAND is not set # # EDAC - error detection and reporting (RAS) (EXPERIMENTAL) # # # Real Time Clock # # # File systems # CONFIG_EXT2_FS=m # CONFIG_EXT2_FS_XATTR is not set # CONFIG_EXT2_FS_XIP is not set # CONFIG_EXT3_FS is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set CONFIG_XFS_FS=y # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_SECURITY is not set # CONFIG_XFS_POSIX_ACL is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y # CONFIG_ZISOFS is not set # CONFIG_UDF_FS is not set # # DOS/FAT/NT Filesystems # # CONFIG_MSDOS_FS is not set # CONFIG_VFAT_FS is not set # CONFIG_NTFS_FS is not set # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y # CONFIG_TMPFS is not set # CONFIG_HUGETLBFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y # # Miscellaneous filesystems # # CONFIG_HFSPLUS_FS is not set # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set # # Network File Systems # # CONFIG_NFS_FS is not set # CONFIG_NFSD is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y # # Native Language Support # CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set CONFIG_NLS_CODEPAGE_850=m # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set # CONFIG_NLS_ASCII is not set CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set CONFIG_NLS_ISO8859_15=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set # CONFIG_MAGIC_SYSRQ is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=14 CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_FS is not set # CONFIG_UNWIND_INFO is not set CONFIG_EARLY_PRINTK=y CONFIG_STACK_BACKTRACE_COLS=2 CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y CONFIG_DOUBLEFAULT=y # # Security options # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # CONFIG_CRYPTO=y CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=y CONFIG_CRYPTO_SHA512=y # CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_SERPENT=m # CONFIG_CRYPTO_AES is not set CONFIG_CRYPTO_AES_586=y # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set # CONFIG_CRYPTO_TEA is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set CONFIG_CRYPTO_DEFLATE=y # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_TEST is not set # # Hardware crypto devices # # CONFIG_CRYPTO_DEV_PADLOCK is not set # # Library routines # CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC32=m CONFIG_LIBCRC32C=m CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=y CONFIG_TEXTSEARCH_BM=y CONFIG_TEXTSEARCH_FSM=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_X86_BIOS_REBOOT=y CONFIG_KTIME_SCALAR=y Some other (maybe) relevant info: root@Teti:~# mii-tool eth2 -vvvv eth2: negotiated 100baseTx-FD flow-control, link ok registers for MII PHY 24: 3000 782d 0041 6800 05e1 45e1 0007 2801 0000 0000 0000 0000 0000 0000 0000 0000 0618 c011 0030 4001 40c8 a000 0000 0000 d300 0220 8084 9119 0065 1b2a 7fff 0000 product info: vendor 00:10:5a, model 0 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control root@Teti:~# ethtool eth2 Settings for eth2: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 24 Transceiver: internal Auto-negotiation: on Current message level: 0x00000001 (1) Link detected: yes root@Teti:~# lsmod Module Size Used by ip_nat_ftp 2816 0 ip_conntrack_ftp 6096 1 ip_nat_ftp 3c59x 38088 0 8139too 20672 0 mii 4480 2 3c59x,8139too crc32 3872 1 8139too ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX 2006-05-23 13:36 ` NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX Marco Berizzi @ 2006-05-23 20:58 ` Steffen Klassert 2006-06-06 9:12 ` Marco Berizzi 0 siblings, 1 reply; 5+ messages in thread From: Steffen Klassert @ 2006-05-23 20:58 UTC (permalink / raw) To: Marco Berizzi; +Cc: netdev On Tue, May 23, 2006 at 03:36:35PM +0200, Marco Berizzi wrote: > Steffen Klassert wrote: > > >On Wed, Apr 05, 2006 at 06:33:18PM +0200, Marco Berizzi wrote: > >> Hello everybody. > >> I'm getting these errors (with packet/connectivity loss) on > >> our firewall after I have plugged in a 3c905C nic. Linux is > >> Slackware 10.2 with vanilla 2.6.16.1. > >> > >> Hints? > >> > >> PS: I have temporary resolved the problem running 'ifconfig > >> eth2 down' and 'ifconfig eth2 up' > >> > >> Apr 5 17:47:07 Teti kernel: eth2: Resetting the Tx ring pointer. > >> Apr 5 17:47:47 Teti last message repeated 4 times > >> Apr 5 17:48:57 Teti last message repeated 7 times > >> Apr 5 17:49:57 Teti last message repeated 6 times > >> Apr 5 17:50:57 Teti last message repeated 6 times > >> > >> Apr 5 17:47:07 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed out > > > >There were some problems of this kind with 10base2 networks in 2.6.16. > >Could you please try whether 2.6.17-rc1 has this problems too? > > [Sorry for the very huge delay, but after 2.6.17-rc1 upgrade > xfs filesystem crashed]. > > Same problem here with 2.6.17-rc3-git18. Running ifconfig > eth2 down and ifconfig eth2 up resolves the problem for > a while. Actually I have not really an idea what is going on here, but increasing the debug level could give some more informations. Setting debug=4 is a good start. Did you try older kernel versions too? Steffen ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX 2006-05-23 20:58 ` Steffen Klassert @ 2006-06-06 9:12 ` Marco Berizzi 2006-06-06 19:13 ` Steffen Klassert 0 siblings, 1 reply; 5+ messages in thread From: Marco Berizzi @ 2006-06-06 9:12 UTC (permalink / raw) To: klassert; +Cc: netdev Steffen Klassert wrote: >On Tue, May 23, 2006 at 03:36:35PM +0200, Marco Berizzi wrote: > > Steffen Klassert wrote: > > > > >On Wed, Apr 05, 2006 at 06:33:18PM +0200, Marco Berizzi wrote: > > >> Hello everybody. > > >> I'm getting these errors (with packet/connectivity loss) on > > >> our firewall after I have plugged in a 3c905C nic. Linux is > > >> Slackware 10.2 with vanilla 2.6.16.1. > > >> > > >> Hints? > > >> > > >> PS: I have temporary resolved the problem running 'ifconfig > > >> eth2 down' and 'ifconfig eth2 up' > > >> > > >> Apr 5 17:47:07 Teti kernel: eth2: Resetting the Tx ring pointer. > > >> Apr 5 17:47:47 Teti last message repeated 4 times > > >> Apr 5 17:48:57 Teti last message repeated 7 times > > >> Apr 5 17:49:57 Teti last message repeated 6 times > > >> Apr 5 17:50:57 Teti last message repeated 6 times > > >> > > >> Apr 5 17:47:07 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed >out > > > > > >There were some problems of this kind with 10base2 networks in 2.6.16. > > >Could you please try whether 2.6.17-rc1 has this problems too? > > > > [Sorry for the very huge delay, but after 2.6.17-rc1 upgrade > > xfs filesystem crashed]. > > > > Same problem here with 2.6.17-rc3-git18. Running ifconfig > > eth2 down and ifconfig eth2 up resolves the problem for > > a while. > >Actually I have not really an idea what is going on here, >but increasing the debug level could give some more informations. >Setting debug=4 is a good start. I have moved this damn pc from the remote to my site and I have placed it in production environment with 2.6.17-rc5 No problem after 24 hours (on the remote side the problem was arising after a couple of hours). I have modprobed 3c59x with debug=4. I see only these kind of messages (are they fine?): Jun 5 14:31:25 Pleiadi kernel: eth2: vortex_error(), status=0x8081 Jun 5 14:31:40 Pleiadi last message repeated 3 times Jun 5 14:31:47 Pleiadi kernel: eth2: vortex_error(), status=0x8281 Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer tick happened, Autonegotiate. Jun 5 14:31:47 Pleiadi kernel: dev->watchdog_timeo=1250 Jun 5 14:31:47 Pleiadi kernel: eth2: MII transceiver has status 782d. Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer finished, Autonegotiate. Jun 5 14:31:51 Pleiadi kernel: eth2: vortex_error(), status=0x8081 Jun 5 14:32:03 Pleiadi last message repeated 2 times Jun 5 14:32:10 Pleiadi kernel: eth2: vortex_error(), status=0x8481 Jun 5 14:32:15 Pleiadi kernel: eth2: vortex_error(), status=0x8081 Jun 5 14:32:46 Pleiadi last message repeated 7 times The only relevant change, between the remote and my site, is a different ethernet switch where the 3c905C is connected to. Could it be an issue? >Did you try older kernel versions too? I started with 2.6.16.x because I need iptables policy match. ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX 2006-06-06 9:12 ` Marco Berizzi @ 2006-06-06 19:13 ` Steffen Klassert 2006-06-16 12:44 ` Marco Berizzi 0 siblings, 1 reply; 5+ messages in thread From: Steffen Klassert @ 2006-06-06 19:13 UTC (permalink / raw) To: Marco Berizzi; +Cc: netdev On Tue, Jun 06, 2006 at 11:12:45AM +0200, Marco Berizzi wrote: > > I have moved this damn pc from the remote to my site and I have > placed it in production environment with 2.6.17-rc5 > No problem after 24 hours (on the remote side the problem was > arising after a couple of hours). I have modprobed 3c59x with > debug=4. I see only these kind of messages (are they fine?): > > Jun 5 14:31:25 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > Jun 5 14:31:40 Pleiadi last message repeated 3 times > Jun 5 14:31:47 Pleiadi kernel: eth2: vortex_error(), status=0x8281 > Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer tick happened, > Autonegotiate. > Jun 5 14:31:47 Pleiadi kernel: dev->watchdog_timeo=1250 > Jun 5 14:31:47 Pleiadi kernel: eth2: MII transceiver has status 782d. > Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer finished, > Autonegotiate. > Jun 5 14:31:51 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > Jun 5 14:32:03 Pleiadi last message repeated 2 times > Jun 5 14:32:10 Pleiadi kernel: eth2: vortex_error(), status=0x8481 > Jun 5 14:32:15 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > Jun 5 14:32:46 Pleiadi last message repeated 7 times This is ok, just normal operation of the NIC. > > The only relevant change, between the remote and my site, is a > different ethernet switch where the 3c905C is connected to. > Could it be an issue? Well, I think it can. Problems with a switch are mostly related to the autonegotiation of the media type and full/half-duplex. But in your case the autonegotiation seems to be ok (mii-tool/ethtool output). More specific information you can get with the mii-diag and vortex-diag tools. You can find these tools at http://www.scyld.com/ethercard_diag.html There are problems with a cisco switch documented in Documentation/networking/vortex.txt for example. Steffen ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX 2006-06-06 19:13 ` Steffen Klassert @ 2006-06-16 12:44 ` Marco Berizzi 0 siblings, 0 replies; 5+ messages in thread From: Marco Berizzi @ 2006-06-16 12:44 UTC (permalink / raw) To: klassert; +Cc: netdev Steffen Klassert wrote: >On Tue, Jun 06, 2006 at 11:12:45AM +0200, Marco Berizzi wrote: > > > > I have moved this damn pc from the remote to my site and I have > > placed it in production environment with 2.6.17-rc5 > > No problem after 24 hours (on the remote side the problem was > > arising after a couple of hours). I have modprobed 3c59x with > > debug=4. I see only these kind of messages (are they fine?): > > > > Jun 5 14:31:25 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > > Jun 5 14:31:40 Pleiadi last message repeated 3 times > > Jun 5 14:31:47 Pleiadi kernel: eth2: vortex_error(), status=0x8281 > > Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer tick >happened, > > Autonegotiate. > > Jun 5 14:31:47 Pleiadi kernel: dev->watchdog_timeo=1250 > > Jun 5 14:31:47 Pleiadi kernel: eth2: MII transceiver has status 782d. > > Jun 5 14:31:47 Pleiadi kernel: eth2: Media selection timer finished, > > Autonegotiate. > > Jun 5 14:31:51 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > > Jun 5 14:32:03 Pleiadi last message repeated 2 times > > Jun 5 14:32:10 Pleiadi kernel: eth2: vortex_error(), status=0x8481 > > Jun 5 14:32:15 Pleiadi kernel: eth2: vortex_error(), status=0x8081 > > Jun 5 14:32:46 Pleiadi last message repeated 7 times > >This is ok, just normal operation of the NIC. > > > > > The only relevant change, between the remote and my site, is a > > different ethernet switch where the 3c905C is connected to. > > Could it be an issue? > >Well, I think it can. Problems with a switch are mostly related >to the autonegotiation of the media type and full/half-duplex. >But in your case the autonegotiation seems to be ok >(mii-tool/ethtool output). More specific information you can >get with the mii-diag and vortex-diag tools. You can find >these tools at http://www.scyld.com/ethercard_diag.html > >There are problems with a cisco switch documented in >Documentation/networking/vortex.txt for example. [moved again this pc to the original site] I have modprobed 3c59x with debug=6 and after a while (about 100 minutes) this error has been arised. Here is the log. Doy you see anything relevant? I don't understand why running an ifconfig eth2 down/up 'resolves' the issue for another 100 minutes. Jun 16 14:01:34 Teti kernel: eth2: interrupt, status 8401, latency 2 ticks. Jun 16 14:01:34 Teti kernel: eth2: In interrupt loop, status 8401. Jun 16 14:01:34 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:34 Teti kernel: boomerang_rx(): status 8001 Jun 16 14:01:34 Teti kernel: Receiving packet size 60 status a000803c. Jun 16 14:01:34 Teti kernel: eth2: exiting interrupt, status 8000. Jun 16 14:01:34 Teti kernel: eth2: interrupt, status 8401, latency 1 ticks. Jun 16 14:01:34 Teti kernel: eth2: In interrupt loop, status 8401. Jun 16 14:01:34 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:34 Teti kernel: boomerang_rx(): status 8001 Jun 16 14:01:34 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:01:34 Teti kernel: eth2: exiting interrupt, status 8000. Jun 16 14:01:36 Teti kernel: eth2: interrupt, status 8401, latency 2 ticks. Jun 16 14:01:36 Teti kernel: eth2: In interrupt loop, status 8401. Jun 16 14:01:36 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:36 Teti kernel: boomerang_rx(): status 8001 Jun 16 14:01:36 Teti kernel: Receiving packet size 82 status 60008052. Jun 16 14:01:36 Teti kernel: eth2: exiting interrupt, status 8000. Jun 16 14:01:36 Teti kernel: eth2: interrupt, status 8401, latency 2 ticks. Jun 16 14:01:36 Teti kernel: eth2: In interrupt loop, status 8401. Jun 16 14:01:36 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:36 Teti kernel: boomerang_rx(): status 8001 Jun 16 14:01:36 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:01:36 Teti kernel: eth2: exiting interrupt, status 8000. Jun 16 14:01:38 Teti kernel: eth2: interrupt, status 8401, latency 2 ticks. Jun 16 14:01:38 Teti kernel: eth2: In interrupt loop, status 8401. Jun 16 14:01:38 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:38 Teti kernel: boomerang_rx(): status 8001 Jun 16 14:01:38 Teti kernel: Receiving packet size 60 status 6000803c. Jun 16 14:01:38 Teti kernel: eth2: exiting interrupt, status 8000. Jun 16 14:01:39 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed out Jun 16 14:01:39 Teti kernel: eth2: transmit timed out, tx_status 00 status 8000. Jun 16 14:01:39 Teti kernel: diagnostics: net 0ccc media 8880 dma 000000a0 fifo 0000 Jun 16 14:01:39 Teti kernel: Flags; bus-master 1, dirty 10411(11) current 10427(11) Jun 16 14:01:39 Teti kernel: Transmit list 159258e0 vs. d59258e0. Jun 16 14:01:39 Teti kernel: 0: @d5925200 length 80000086 status 00000086 Jun 16 14:01:39 Teti kernel: 1: @d59252a0 length 800000ec status 000000ec Jun 16 14:01:39 Teti kernel: 2: @d5925340 length 8000003f status 0000003f Jun 16 14:01:39 Teti kernel: 3: @d59253e0 length 800000ec status 000000ec Jun 16 14:01:39 Teti kernel: 4: @d5925480 length 8000003f status 0000003f Jun 16 14:01:39 Teti kernel: 5: @d5925520 length 800000ec status 000000ec Jun 16 14:01:39 Teti kernel: 6: @d59255c0 length 8000002a status 0000002a Jun 16 14:01:39 Teti kernel: 7: @d5925660 length 8000003f status 0000003f Jun 16 14:01:39 Teti kernel: 8: @d5925700 length 800000ec status 000000ec Jun 16 14:01:39 Teti kernel: 9: @d59257a0 length 800000ec status 800000ec Jun 16 14:01:39 Teti kernel: 10: @d5925840 length 800000ec status 800000ec Jun 16 14:01:39 Teti kernel: 11: @d59258e0 length 8000082a status 0000082a Jun 16 14:01:39 Teti kernel: 12: @d5925980 length 80000086 status 00000086 Jun 16 14:01:39 Teti kernel: 13: @d5925a20 length 80000037 status 00000037 Jun 16 14:01:39 Teti kernel: 14: @d5925ac0 length 80000036 status 00000036 Jun 16 14:01:39 Teti kernel: 15: @d5925b60 length 8000003f status 0000003f Jun 16 14:01:39 Teti kernel: eth2: Resetting the Tx ring pointer. Jun 16 14:01:39 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:39 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:39 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:39 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:39 Teti kernel: Receiving packet size 82 status 60008052. Jun 16 14:01:39 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:41 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:41 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:41 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:41 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:41 Teti kernel: Receiving packet size 82 status a0008052. Jun 16 14:01:41 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:42 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:01:42 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:42 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:42 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:42 Teti kernel: Receiving packet size 82 status a0008052. Jun 16 14:01:42 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:43 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:43 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:43 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:43 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:43 Teti kernel: Receiving packet size 82 status a0008052. Jun 16 14:01:43 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:44 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:44 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:44 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:44 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:44 Teti kernel: Receiving packet size 92 status a000805c. Jun 16 14:01:44 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:44 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:44 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:44 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:44 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:44 Teti kernel: Receiving packet size 243 status a00080f3. Jun 16 14:01:44 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:45 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:01:45 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:45 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:45 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:45 Teti kernel: Receiving packet size 92 status a000805c. Jun 16 14:01:45 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:45 Teti kernel: eth2: interrupt, status e401, latency 5 ticks. Jun 16 14:01:45 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:45 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:45 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:45 Teti kernel: Receiving packet size 60 status 6000803c. Jun 16 14:01:45 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:45 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:45 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:45 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:45 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:45 Teti kernel: Receiving packet size 76 status a000804c. Jun 16 14:01:45 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:46 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:46 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:46 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:46 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:46 Teti kernel: Receiving packet size 92 status a000805c. Jun 16 14:01:46 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:46 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:46 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:46 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:46 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:46 Teti kernel: Receiving packet size 247 status a00080f7. Jun 16 14:01:46 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:46 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:46 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:46 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:46 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:46 Teti kernel: Receiving packet size 247 status a00080f7. Jun 16 14:01:46 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:46 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:01:46 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:46 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:46 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:46 Teti kernel: Receiving packet size 76 status a000804c. Jun 16 14:01:46 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:47 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:47 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:47 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:47 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:47 Teti kernel: Receiving packet size 82 status 60008052. Jun 16 14:01:47 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:47 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:01:47 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:47 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:47 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:47 Teti kernel: Receiving packet size 76 status a000804c. Jun 16 14:01:47 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:48 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:01:48 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:01:48 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:01:48 Teti kernel: boomerang_rx(): status e001 Jun 16 14:01:48 Teti kernel: Receiving packet size 60 status 6000803c. Jun 16 14:01:48 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:01:49 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed out Jun 16 14:01:49 Teti kernel: eth2: transmit timed out, tx_status 00 status e000. Jun 16 14:01:49 Teti kernel: diagnostics: net 0ccc media 8880 dma 000000a0 fifo 0000 Jun 16 14:01:49 Teti kernel: Flags; bus-master 1, dirty 10411(11) current 10427(11) Jun 16 14:01:49 Teti kernel: Transmit list 159258e0 vs. d59258e0. Here is the log when I run ifconfig eth2 down and ifconfig eth2 up: Jun 16 14:19:49 Teti kernel: NETDEV WATCHDOG: eth2: transmit timed out Jun 16 14:19:49 Teti kernel: eth2: transmit timed out, tx_status 00 status e000. Jun 16 14:19:49 Teti kernel: diagnostics: net 0ccc media 8880 dma 000000a0 fifo 0000 Jun 16 14:19:49 Teti kernel: Flags; bus-master 1, dirty 10411(11) current 10427(11) Jun 16 14:19:49 Teti kernel: Transmit list 159258e0 vs. d59258e0. Jun 16 14:19:49 Teti kernel: 0: @d5925200 length 80000086 status 00000086 Jun 16 14:19:49 Teti kernel: 1: @d59252a0 length 800000ec status 000000ec Jun 16 14:19:49 Teti kernel: 2: @d5925340 length 8000003f status 0000003f Jun 16 14:19:49 Teti kernel: 3: @d59253e0 length 800000ec status 000000ec Jun 16 14:19:49 Teti kernel: 4: @d5925480 length 8000003f status 0000003f Jun 16 14:19:49 Teti kernel: 5: @d5925520 length 800000ec status 000000ec Jun 16 14:19:49 Teti kernel: 6: @d59255c0 length 8000002a status 0000002a Jun 16 14:19:49 Teti kernel: 7: @d5925660 length 8000003f status 0000003f Jun 16 14:19:49 Teti kernel: 8: @d5925700 length 800000ec status 000000ec Jun 16 14:19:49 Teti kernel: 9: @d59257a0 length 800000ec status 800000ec Jun 16 14:19:49 Teti kernel: 10: @d5925840 length 800000ec status 800000ec Jun 16 14:19:49 Teti kernel: 11: @d59258e0 length 8000082a status 0000082a Jun 16 14:19:49 Teti kernel: 12: @d5925980 length 80000086 status 00000086 Jun 16 14:19:49 Teti kernel: 13: @d5925a20 length 80000037 status 00000037 Jun 16 14:19:49 Teti kernel: 14: @d5925ac0 length 80000036 status 00000036 Jun 16 14:19:49 Teti kernel: 15: @d5925b60 length 8000003f status 0000003f Jun 16 14:19:49 Teti kernel: eth2: Resetting the Tx ring pointer. Jun 16 14:19:49 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:49 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:49 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:49 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:49 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:49 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:49 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:49 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:49 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:49 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:49 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:49 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:50 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:50 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:50 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:50 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:50 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:50 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:51 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:51 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:51 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:51 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:51 Teti kernel: Receiving packet size 71 status a0008047. Jun 16 14:19:51 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:51 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:19:51 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:51 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:51 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:51 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:51 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:51 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:51 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:51 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:51 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:51 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:51 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:52 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:52 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:52 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:52 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:52 Teti kernel: Receiving packet size 71 status a0008047. Jun 16 14:19:52 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:52 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:52 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:52 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:52 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:52 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:52 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:53 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:53 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:53 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:53 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:53 Teti kernel: Receiving packet size 71 status a0008047. Jun 16 14:19:53 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:53 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:53 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:53 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:53 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:53 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:53 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:54 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:54 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:54 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:54 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:54 Teti kernel: Receiving packet size 92 status a000805c. Jun 16 14:19:54 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:54 Teti kernel: eth2: interrupt, status e401, latency 2 ticks. Jun 16 14:19:54 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:54 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:54 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:54 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:54 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:54 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:19:54 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:54 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:54 Teti kernel: boomerang_rx(): status e001 Jun 16 14:19:54 Teti kernel: Receiving packet size 60 status 803c. Jun 16 14:19:54 Teti kernel: eth2: exiting interrupt, status e000. Jun 16 14:19:55 Teti kernel: eth2: vortex_close() status e000, Tx status 00. Jun 16 14:19:55 Teti kernel: eth2: vortex close stats: rx_nocopy 10191 rx_copy 46830 tx_queued 51612 Rx pre-checksummed 52779. Jun 16 14:19:57 Teti kernel: eth2: Filling in the Rx ring. Jun 16 14:19:57 Teti kernel: PCI: Found IRQ 7 for device 0000:01:09.0 Jun 16 14:19:57 Teti kernel: eth2: using NWAY device table, not 8 Jun 16 14:19:57 Teti kernel: eth2: Initial media type Autonegotiate. Jun 16 14:19:57 Teti kernel: eth2: link up, 100Mbps, full-duplex, lpa 0x45E1 Jun 16 14:19:57 Teti kernel: eth2: setting full-duplex. Jun 16 14:19:57 Teti kernel: eth2: vortex_up() irq 7 media status 8880. Jun 16 14:19:57 Teti kernel: eth2: interrupt, status e401, latency 1 ticks. Jun 16 14:19:57 Teti kernel: eth2: In interrupt loop, status e401. Jun 16 14:19:57 Teti kernel: boomerang_interrupt->boomerang_rx Jun 16 14:19:57 Teti kernel: boomerang_rx(): status e001 PS: linux is vanilla 2.6.17-rc6 ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2006-06-16 12:44 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20060405175033.GE16850@bayes.mathematik.tu-chemnitz.de>
2006-05-23 13:36 ` NETDEV WATCHDOG: eth2: transmit timed out with 3c905C-TX Marco Berizzi
2006-05-23 20:58 ` Steffen Klassert
2006-06-06 9:12 ` Marco Berizzi
2006-06-06 19:13 ` Steffen Klassert
2006-06-16 12:44 ` Marco Berizzi
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox