Netdev List
 help / color / mirror / Atom feed
* [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r)
@ 2026-11-18 15:18 Frits Letteboer
  2026-11-18 15:32 ` Andrew Lunn
  2026-11-18 15:44 ` Thorsten Leemhuis
  0 siblings, 2 replies; 3+ messages in thread
From: Frits Letteboer @ 2026-11-18 15:18 UTC (permalink / raw)
  To: hkallweit1; +Cc: netdev, regressions, andrew, rmk+kernel

Hi Heiner,

Between Linux 7.3 and 7.4-rc3, my Realtek RTL8127A (XID 6c9) SFP+ NIC
stopped establishing a link and generating interrupts under r8169.

Hardware details:
- NIC: Realtek RTL8127 10GbE Controller (rev 08), XID 6c9
- Transceiver: Intel FTLX8571D3BCV-IT (10GBASE-SR SFP+)

On Linux 7.3, r8169 attached the "Realtek SFP PHY Mode" driver and
brought up the 10Gbps link normally. On 7.4-rc3, r8169 configures
"inband/10gbase-r link mode" via phylink, after which "Link detected"
remains "no", no link state transitions are logged, and zero IRQs fire.

Tested workarounds on 7.4-rc3:
- pci=nomsix, iommu=pt, amd_iommu=off: no effect
- Realtek out-of-tree r8127 driver (11.017.02) on 7.4-rc3: works
   properly and brings the 10G link up immediately.

--- dmesg on Linux 7.3 (working) ---
[    3.777598] r8169 0000:0a:00.0 eth1: RTL8127A, 8c:a6:82:71:89:12, XID 
6c9, IRQ 152
[    3.777601] r8169 0000:0a:00.0 eth1: jumbo features [frames: 16362 
bytes, tx checksumming: ko]
[   13.540664] r8169 0000:0a:00.0 re0: renamed from eth1
[   34.179244] Realtek SFP PHY Mode r8169-0-a00:00: attached PHY driver 
(mii_bus:phy_addr=r8169-0-a00:0, irq=MAC)
[   34.871337] r8169 0000:0a:00.0 re0: Link is Down
[   35.053740] r8169 0000:0a:00.0 re0: Link is Up - 10Gbps/Full - flow 
control off

--- dmesg on Linux 7.4-rc3 (broken) ---
[    3.806559] r8169 0000:0a:00.0 eth1: RTL8127A, 8c:a6:82:71:89:12, XID 
6c9, IRQ 152 (32 total)
[    3.806562] r8169 0000:0a:00.0 eth1: jumbo features [frames: 16362 
bytes, tx checksumming: ko]
[   14.285134] r8169 0000:0a:00.0 re0: renamed from eth1
[   34.926923] r8169 0000:0a:00.0 re0: configuring for inband/10gbase-r 
link mode
[   40.505158] r8169 0000:0a:00.0: invalid VPD tag 0x00 (size 0) at 
offset 0; assume missing optional EEPROM

--- ethtool re0 on Linux 7.4-rc3 ---
Settings for re0:
     Supported ports: [ MII ]
     Supported link modes:   10000baseT/Full
                             10000baseKX4/Full
                             10000baseKR/Full
                             10000baseR_FEC
                             10000baseCR/Full
                             10000baseSR/Full
                             10000baseLR/Full
                             10000baseLRM/Full
                             10000baseER/Full
     Supported pause frame use: No
     Supports auto-negotiation: Yes
     Supported FEC modes: Not reported
     Advertised link modes:  10000baseT/Full
                             10000baseKX4/Full
                             10000baseKR/Full
                             10000baseR_FEC
                             10000baseCR/Full
                             10000baseSR/Full
                             10000baseLR/Full
                             10000baseLRM/Full
                             10000baseER/Full
     Advertised pause frame use: No
     Advertised auto-negotiation: Yes
     Advertised FEC modes: Not reported
     Speed: 10000Mb/s
     Duplex: Full
     Auto-negotiation: on
     Port: MII
     PHYAD: 0
     Transceiver: internal
     Supports Wake-on: pumbg
     Wake-on: d
     Link detected: no

I am happy to test any diagnostic patches on this hardware.

Thanks!


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r)
  2026-11-18 15:18 [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r) Frits Letteboer
@ 2026-11-18 15:32 ` Andrew Lunn
  2026-11-18 15:44 ` Thorsten Leemhuis
  1 sibling, 0 replies; 3+ messages in thread
From: Andrew Lunn @ 2026-11-18 15:32 UTC (permalink / raw)
  To: Frits Letteboer; +Cc: hkallweit1, netdev, regressions, rmk+kernel

On Wed, Nov 18, 2026 at 04:18:41PM +0100, Frits Letteboer wrote:
> Hi Heiner,
> 
> Between Linux 7.3 and 7.4-rc3, my Realtek RTL8127A (XID 6c9) SFP+ NIC
> stopped establishing a link and generating interrupts under r8169.

Can you do a git bisect? Find out which patch broken it?

    Andrew

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r)
  2026-11-18 15:18 [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r) Frits Letteboer
  2026-11-18 15:32 ` Andrew Lunn
@ 2026-11-18 15:44 ` Thorsten Leemhuis
  1 sibling, 0 replies; 3+ messages in thread
From: Thorsten Leemhuis @ 2026-11-18 15:44 UTC (permalink / raw)
  To: Frits Letteboer, hkallweit1; +Cc: netdev, regressions, andrew, rmk+kernel

On 11/18/26 16:18, Frits Letteboer wrote:
> 
> Between Linux 7.3 and 7.4-rc3, my Realtek RTL8127A (XID 6c9) SFP+ NIC
> stopped establishing a link and generating interrupts under r8169.
> 
> Hardware details:
> - NIC: Realtek RTL8127 10GbE Controller (rev 08), XID 6c9
> - Transceiver: Intel FTLX8571D3BCV-IT (10GBASE-SR SFP+)
> 
> On Linux 7.3, r8169 attached the "Realtek SFP PHY Mode" driver and
> brought up the 10Gbps link normally. On 7.4-rc3, r8169 configures
> "inband/10gbase-r link mode" via phylink, after which "Link detected"
> remains "no", no link state transitions are logged, and zero IRQs fire.
> 
> Tested workarounds on 7.4-rc3:
> - pci=nomsix, iommu=pt, amd_iommu=off: no effect
> - Realtek out-of-tree r8127 driver (11.017.02) on 7.4-rc3: works
>   properly and brings the 10G link up immediately.
> 
> --- dmesg on Linux 7.3 (working) ---
> [    3.777598] r8169 0000:0a:00.0 eth1: RTL8127A, 8c:a6:82:71:89:12, XID
> 6c9, IRQ 152
> [    3.777601] r8169 0000:0a:00.0 eth1: jumbo features [frames: 16362
> bytes, tx checksumming: ko]
> [   13.540664] r8169 0000:0a:00.0 re0: renamed from eth1
> [   34.179244] Realtek SFP PHY Mode r8169-0-a00:00: attached PHY driver
> (mii_bus:phy_addr=r8169-0-a00:0, irq=MAC)
> [   34.871337] r8169 0000:0a:00.0 re0: Link is Down
> [   35.053740] r8169 0000:0a:00.0 re0: Link is Up - 10Gbps/Full - flow
> control off
> 
> --- dmesg on Linux 7.4-rc3 (broken) ---
> [    3.806559] r8169 0000:0a:00.0 eth1: RTL8127A, 8c:a6:82:71:89:12, XID
> 6c9, IRQ 152 (32 total)
> [    3.806562] r8169 0000:0a:00.0 eth1: jumbo features [frames: 16362
> bytes, tx checksumming: ko]
> [   14.285134] r8169 0000:0a:00.0 re0: renamed from eth1
> [   34.926923] r8169 0000:0a:00.0 re0: configuring for inband/10gbase-r
> link mode
> [   40.505158] r8169 0000:0a:00.0: invalid VPD tag 0x00 (size 0) at
> offset 0; assume missing optional EEPROM

This is not my area of expertise, so the following might mislead you.
Nevertheless FWIW:

That error msg recently showed up here, so I wonder if it might be related:
https://lore.kernel.org/all/20260522114135.2104890-1-18255117159@163.com/

Ciao, Thorsten

> --- ethtool re0 on Linux 7.4-rc3 ---
> Settings for re0:
>     Supported ports: [ MII ]
>     Supported link modes:   10000baseT/Full
>                             10000baseKX4/Full
>                             10000baseKR/Full
>                             10000baseR_FEC
>                             10000baseCR/Full
>                             10000baseSR/Full
>                             10000baseLR/Full
>                             10000baseLRM/Full
>                             10000baseER/Full
>     Supported pause frame use: No
>     Supports auto-negotiation: Yes
>     Supported FEC modes: Not reported
>     Advertised link modes:  10000baseT/Full
>                             10000baseKX4/Full
>                             10000baseKR/Full
>                             10000baseR_FEC
>                             10000baseCR/Full
>                             10000baseSR/Full
>                             10000baseLR/Full
>                             10000baseLRM/Full
>                             10000baseER/Full
>     Advertised pause frame use: No
>     Advertised auto-negotiation: Yes
>     Advertised FEC modes: Not reported
>     Speed: 10000Mb/s
>     Duplex: Full
>     Auto-negotiation: on
>     Port: MII
>     PHYAD: 0
>     Transceiver: internal
>     Supports Wake-on: pumbg
>     Wake-on: d
>     Link detected: no
> 
> I am happy to test any diagnostic patches on this hardware.
> 
> Thanks!


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2026-11-18 15:48 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-18 15:18 [REGRESSION] r8169: RTL8127A (XID 6c9) SFP+ link fails to come up in 7.4-rc3 (inband/10gbase-r) Frits Letteboer
2026-11-18 15:32 ` Andrew Lunn
2026-11-18 15:44 ` Thorsten Leemhuis

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox