* network freeze with nforce-A939 integrated rhine card
From: David Lang @ 2006-05-12 5:59 UTC (permalink / raw)
To: linux-kernel, rl; +Cc: netdev
[-- Attachment #1: Type: TEXT/PLAIN, Size: 3093 bytes --]
I haven't had time to go back and find where is started (my prior kernel
was 2.6.15-rc7), but with 2.6.17-rc1/2/3/4 I've been running into a
problem where when transfering large amounts of data (trying to ftp a TB
or so of data off of the box to my new server it will run for a while (as
little as 1G, as much as 45G) and then the network card will shut down.
when I say shut down I mean that it looses link and requires powering down
the box (hard power down, not just power off from the front panel),
disabling the network card in the BIOS, booting (as far as lilo is
enough), powering down again, enabling the card and booting again.
there is no indication of trouble before the halt (it's transfering at
full speed), the only think in the log is
May 11 22:23:57 david kernel: eth0: link down
May 11 22:24:00 david kernel: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
May 11 22:24:22 david kernel: eth0: link down
if I don't do the disable/enable in the bios cycle and just power cycle
the system the card does not initialize properly (ethtool reports
autonegotiation disabled, 10Mb. will generate an 'unsupported' error if I
try to enable the card)
the system is x86_64 64 bit kernel with 32 bit userspace
lspci report
dlang@david:~$ /sbin/lspci
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0204
00:00.1 Host bridge: VIA Technologies, Inc.: Unknown device 1204
00:00.2 Host bridge: VIA Technologies, Inc.: Unknown device 2204
00:00.3 Host bridge: VIA Technologies, Inc.: Unknown device 3204
00:00.4 Host bridge: VIA Technologies, Inc.: Unknown device 4204
00:00.7 Host bridge: VIA Technologies, Inc.: Unknown device 7204
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South]
00:08.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
00:08.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
00:0a.0 Ethernet controller: Olicom OC-2326 (rev 01)
00:0f.0 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C/VT8235 PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT6202 [USB 2.0 controller] (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (rev 01)
config is attached
David Lang
[-- Attachment #2: Type: APPLICATION/octet-stream, Size: 9962 bytes --]
^ permalink raw reply
* Re: [Bugme-new] [Bug 6530] New: MAINLINE
From: Andy Gay @ 2006-05-12 2:12 UTC (permalink / raw)
To: Paul Mackerras; +Cc: Andrew Morton, bugme-daemon, netdev, xeb
In-Reply-To: <17507.60398.845863.783477@cargo.ozlabs.ibm.com>
On Fri, 2006-05-12 at 11:59 +1000, Paul Mackerras wrote:
> Andy Gay writes:
>
> > How does the serial driver know it has to call ppp_asynctty_wakeup()?
>
> The serial driver is supposed to call the line discipline's wakeup
> function when it has room in the output buffer and the
> TTY_DO_WRITE_WAKEUP bit is set in tty->flags. When the serial port is
> set to the ppp line discipline, then it uses the functions defined in
> the ppp_ldisc structure in drivers/net/ppp_async.c, and the
> write_wakeup field in that structure points to ppp_asynctty_wakeup.
>
OK, thanks for the explanation. I'll pay special attention to that stuff
in my driver!
> > There were a bunch of changes to the serial drivers between 2.6.15 and
> > 2.6.16, maybe that's where this problem was introduced. Do we know which
> > serial driver is involved in the original report?
>
> Apparently it's the pty driver.
>
So I heard. Hopefully the maintainer of that driver will see this....
> Paul.
^ permalink raw reply
* Re: [Bugme-new] [Bug 6530] New: MAINLINE
From: Paul Mackerras @ 2006-05-12 1:59 UTC (permalink / raw)
To: Andy Gay; +Cc: Andrew Morton, bugme-daemon, netdev, xeb
In-Reply-To: <1147326683.29448.80.camel@tahini.andynet.net>
Andy Gay writes:
> How does the serial driver know it has to call ppp_asynctty_wakeup()?
The serial driver is supposed to call the line discipline's wakeup
function when it has room in the output buffer and the
TTY_DO_WRITE_WAKEUP bit is set in tty->flags. When the serial port is
set to the ppp line discipline, then it uses the functions defined in
the ppp_ldisc structure in drivers/net/ppp_async.c, and the
write_wakeup field in that structure points to ppp_asynctty_wakeup.
> There were a bunch of changes to the serial drivers between 2.6.15 and
> 2.6.16, maybe that's where this problem was introduced. Do we know which
> serial driver is involved in the original report?
Apparently it's the pty driver.
Paul.
^ permalink raw reply
* skge driver oops
From: David Arnold @ 2006-05-12 1:36 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: netdev, David Arnold
In-Reply-To: <20060511150952.4c2cde2e@localhost.localdomain>
i've been getting semi-regular lockups on my machine over 2.6.16
series. I recently attached a serial console in an attempt to capture
an OOPS.
i got one yesterday. it's copied manually from the console, but
hopefully the values are all accurate. there was more that had scrolled
off screen above this too (sorry).
oops, lspci, uname -a, .config and dmesg below.
any suggestions for further debugging would be great,
thanks,
d
skb_over_panic: text:c11a5f4c len:1244 put:1127 head:f7514600 data:f7514602 tail:f7514ade
end:f75146c0 dev:eth1
-------[ cut here ]--------
kernel BUG at net/core/skbuff.c:94!
invalid opcode: 0000 [#1]
SMP
Modules linked in: hci_usb i2c_amd756
CPU: 0
EIP: 0060:[<c126f0b3>] Not tainted VLI
EFLAGS: 00210292 (2.6.16.14da #18)
EIP is at skb_over_panic+0x63/0x70
eax: 83
ebx: f7d96ac0
ecx: c13fbe64
edx: 200296
esi: 0
edi: 6b560467
ebp: f71d4810
esp: c14aff44
ds: 7b
es: 7b
ss: 68
Process swapper (pid: 0, threadinfo=c14af000 task=c13f9100)
Stack: <0>c13d9230 c11a5f4c 000004dc 00000467 f7514600 f7514602 f7514ade f75146c0
f7d96800 c11a5f58 f72456e0 00000467 c11a5f4c c1d1ae24 c10222c0 00000600
00000467 00000040 c1e565a0 f7d96ae8 00000000 f72456e0 0467cc2b f7d968c0
Call Trace:
[<c11a5f4c>] skge_poll+0x4bc/0x500
[<c11a5f58>] skge_poll+0x4c8/0x500
[<c11a5f4c>] skge_poll+0x4bc/0x500
[<c10222c0>] it_real_fn+0x0/0x60
[<c1274f6f>] net_rx_action+0x76/0xe0
[<c1023f26>] __do_softirq+0x76/0xe0
[<c10058bb>] do_softirq+0x5b/0x60
==================
[<c1005839>] do_IRQ+0x49/0x70
[<c1003a6a>] common_interrupt+0x1a/0x20
[<c1001ca0>] default_idle+0x0/0x60
[<c1001ccc>] default_idle+0x2c/0x60
[<c1001d64>] cpu_idle+0x64/0x80
[<c146f50f>] start_kernel+0x2df/0x390
[<c146f5c0>] unknown_bootoption+0x0/0x260
Code: 84 00 00 00 89 44 24 10 8b 44 24 2c 89 44 24 2c 89 44 24 0c 8b 41 60 c7 04 24 30 92 3d c1 89 44 24 08 8b 44 24 30 89 44
<0>Kernel panic - not syncing: Fatal exception in interrupt
d@d > lspci
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11)
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05)
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04)
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
0000:00:09.0 Ethernet controller: D-Link System Inc Gigabit Ethernet Adapter (rev 11)
0000:00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05)
0000:01:05.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (rev 01)
0000:01:05.1 Display controller: ATI Technologies Inc: Unknown device 5940 (rev 01)
0000:02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07)
0000:02:06.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
0000:02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
d@d >
d@d > uname -a
Linux d 2.6.16.14da #18 SMP Tue May 9 09:57:15 EST 2006 i686 GNU/Linux
d@d >
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.16.14
# Tue May 9 09:47:17 2006
#
CONFIG_X86_32=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION="da"
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_UID16=y
CONFIG_VM86=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y
#
# Block layer
#
CONFIG_LBD=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
# CONFIG_SCHED_SMT is not set
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
# CONFIG_X86_MCE_P4THERMAL is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
#
# Firmware Drivers
#
CONFIG_EDD=y
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_3G_OPT is not set
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_IRQBALANCE=y
# CONFIG_REGPARM is not set
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
# CONFIG_KEXEC is not set
CONFIG_CRASH_DUMP=y
CONFIG_PHYSICAL_START=0x1000000
# CONFIG_HOTPLUG_CPU is not set
CONFIG_DOUBLEFAULT=y
#
# Power management options (ACPI, APM)
#
# CONFIG_PM is not set
#
# ACPI (Advanced Configuration and Power Interface) Support
#
# CONFIG_ACPI is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY_PROC is not set
# CONFIG_PCI_DEBUG is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
CONFIG_INET_TUNNEL=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
CONFIG_TCP_CONG_ADVANCED=y
#
# TCP congestion control
#
CONFIG_TCP_CONG_BIC=y
CONFIG_TCP_CONG_CUBIC=m
CONFIG_TCP_CONG_WESTWOOD=y
# CONFIG_TCP_CONG_HTCP is not set
# CONFIG_TCP_CONG_HSTCP is not set
# CONFIG_TCP_CONG_HYBLA is not set
# CONFIG_TCP_CONG_VEGAS is not set
# CONFIG_TCP_CONG_SCALABLE is not set
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
CONFIG_INET6_IPCOMP=y
CONFIG_INET6_TUNNEL=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP=y
CONFIG_INET_DCCP_DIAG=y
#
# DCCP CCIDs Configuration (EXPERIMENTAL)
#
CONFIG_IP_DCCP_CCID3=y
CONFIG_IP_DCCP_TFRC_LIB=y
#
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IP_SCTP=y
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
CONFIG_SCTP_HMAC_NONE=y
# CONFIG_SCTP_HMAC_SHA1 is not set
# CONFIG_SCTP_HMAC_MD5 is not set
#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
CONFIG_IRDA=y
#
# IrDA protocols
#
CONFIG_IRLAN=y
CONFIG_IRCOMM=y
CONFIG_IRDA_ULTRA=y
#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
CONFIG_IRDA_DEBUG=y
#
# Infrared-port device drivers
#
#
# SIR device drivers
#
CONFIG_IRTTY_SIR=y
#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=y
CONFIG_ACTISYS_DONGLE=y
CONFIG_TEKRAM_DONGLE=y
# CONFIG_LITELINK_DONGLE is not set
# CONFIG_MA600_DONGLE is not set
# CONFIG_GIRBIL_DONGLE is not set
# CONFIG_MCP2120_DONGLE is not set
# CONFIG_OLD_BELKIN_DONGLE is not set
CONFIG_ACT200L_DONGLE=y
#
# Old SIR device drivers
#
#
# Old Serial dongle support
#
#
# FIR device drivers
#
# CONFIG_USB_IRDA is not set
# CONFIG_SIGMATEL_FIR is not set
# CONFIG_NSC_FIR is not set
# CONFIG_WINBOND_FIR is not set
# CONFIG_TOSHIBA_FIR is not set
# CONFIG_SMC_IRCC_FIR is not set
# CONFIG_ALI_FIR is not set
# CONFIG_VLSI_FIR is not set
# CONFIG_VIA_FIR is not set
CONFIG_BT=y
CONFIG_BT_L2CAP=y
CONFIG_BT_SCO=y
CONFIG_BT_RFCOMM=y
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=y
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=y
#
# Bluetooth device drivers
#
CONFIG_BT_HCIUSB=m
CONFIG_BT_HCIUSB_SCO=y
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
# CONFIG_BT_HCIUART_BCSP is not set
# CONFIG_BT_HCIBCM203X is not set
# CONFIG_BT_HCIBPA10X is not set
# CONFIG_BT_HCIBFUSB is not set
# CONFIG_BT_HCIVHCI is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_SERIAL=y
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_GSC is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_CDROM_PKTCDVD=y
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
CONFIG_PHYLIB=y
#
# MII PHY device drivers
#
CONFIG_MARVELL_PHY=y
CONFIG_DAVICOM_PHY=y
CONFIG_QSEMI_PHY=y
CONFIG_LXT_PHY=y
CONFIG_CICADA_PHY=y
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=y
# CONFIG_TYPHOON is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
CONFIG_SKGE=y
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_UINPUT is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=y
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
CONFIG_AGP_AMD=y
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_CS5535_GPIO is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=m
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
#
CONFIG_SENSORS_DS1337=m
CONFIG_SENSORS_DS1374=m
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS1621=m
# CONFIG_SENSORS_F71805F is not set
CONFIG_SENSORS_FSCHER=m
# CONFIG_SENSORS_FSCPOS is not set
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
# CONFIG_SENSORS_IT87 is not set
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
# CONFIG_SENSORS_LM78 is not set
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
# CONFIG_SENSORS_LM85 is not set
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47B397=m
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT8231 is not set
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
# CONFIG_SENSORS_HDAPS is not set
CONFIG_HWMON_DEBUG_CHIP=y
#
# Misc devices
#
# CONFIG_IBM_ASM is not set
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=y
#
# Video For Linux
#
#
# Video Adapters
#
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_SAA6588=m
CONFIG_VIDEO_BWQCAM=m
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_W9966 is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
CONFIG_VIDEO_CX88=m
# CONFIG_VIDEO_CX88_ALSA is not set
# CONFIG_VIDEO_EM28XX is not set
CONFIG_VIDEO_OVCAMCHIP=m
# CONFIG_VIDEO_AUDIO_DECODER is not set
# CONFIG_VIDEO_DECODER is not set
#
# Radio Adapters
#
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m
CONFIG_VIDEO_TVEEPROM=m
#
# Graphics support
#
# CONFIG_FB is not set
CONFIG_VIDEO_SELECT=y
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_RAWMIDI=y
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_DYNAMIC_MINORS is not set
CONFIG_SND_SUPPORT_OLD_API=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_AC97_CODEC=y
CONFIG_SND_AC97_BUS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# PCI devices
#
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
CONFIG_SND_BT87X=m
# CONFIG_SND_BT87X_OVERCLOCK is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5535AUDIO is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_ENS1370 is not set
CONFIG_SND_ENS1371=y
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_PCXHR is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
CONFIG_USB_STORAGE_DEBUG=y
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_ET61X251 is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
CONFIG_USB_STV680=m
# CONFIG_USB_W9968CF is not set
# CONFIG_USB_PWC is not set
#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=y
# CONFIG_USB_SERIAL_CONSOLE is not set
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_AIRPRIME is not set
# CONFIG_USB_SERIAL_ANYDATA is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
CONFIG_USB_SERIAL_CP2101=m
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
CONFIG_USB_SERIAL_KEYSPAN=y
# CONFIG_USB_SERIAL_KEYSPAN_MPR is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
# CONFIG_USB_SERIAL_KEYSPAN_USA19QI is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49WLC is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
CONFIG_USB_LED=m
# CONFIG_USB_CYTHERM is not set
CONFIG_USB_PHIDGETKIT=y
CONFIG_USB_PHIDGETSERVO=y
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set
#
# USB DSL modem support
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
# CONFIG_EDAC is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_EXT2_FS_POSIX_ACL is not set
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=y
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
# CONFIG_PROC_VMCORE is not set
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
CONFIG_HFSPLUS_FS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=y
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=y
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
CONFIG_DEBUG_MUTEXES=y
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_RODATA is not set
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_SHA1=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_AES_586 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set
#
# Library routines
#
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y
[17179569.184000] Linux version 2.6.16.14da (root@d) (gcc version 4.0.3 (Debian 4.0.3-1)) #18 SMP Tue May 9 09:57:15 EST 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[17179569.184000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
[17179569.184000] BIOS-e820: 000000003fef0000 - 000000003feff000 (ACPI data)
[17179569.184000] BIOS-e820: 000000003feff000 - 000000003ff00000 (ACPI NVS)
[17179569.184000] BIOS-e820: 000000003ff00000 - 000000003ff80000 (usable)
[17179569.184000] BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec04000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 127MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f7170
[17179569.184000] On node 0 totalpages: 262016
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000] Normal zone: 225280 pages, LIFO batch:31
[17179569.184000] HighMem zone: 32640 pages, LIFO batch:7
[17179569.184000] DMI 2.3 present.
[17179569.184000] Intel MultiProcessor Specification v1.4
[17179569.184000] Virtual Wire compatibility mode.
[17179569.184000] OEM ID: TYAN Product ID: PAULANER APIC at: 0xFEE00000
[17179569.184000] Processor #1 6:8 APIC version 16
[17179569.184000] Processor #0 6:8 APIC version 16
[17179569.184000] I/O APIC #2 Version 17 at 0xFEC00000.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Processors: 2
[17179569.184000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: auto BOOT_IMAGE=default ro root=301 console=tty0 console=ttyS1,38400n8
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] CPU 0 irqstacks, hard=c14ad000 soft=c14af000
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[ 0.000000] Detected 2000.441 MHz processor.
[ 40.104994] Using tsc for high-res timesource
[ 40.106624] Console: colour VGA+ 132x44
[ 40.721697] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 40.744539] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 40.806006] Memory: 1033096k/1048064k available (3576k kernel code, 14308k reserved, 956k data, 228k init, 130496k highmem)
[ 40.839342] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 40.941993] Calibrating delay using timer specific routine.. 4008.01 BogoMIPS (lpj=8016031)
[ 40.967140] Mount-cache hash table entries: 512
[ 40.980916] CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 40.980923] CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 40.980932] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.002322] CPU: L2 Cache: 256K (64 bytes/line)
[ 41.015912] CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
[ 41.015918] Intel machine check architecture supported.
[ 41.031584] Intel machine check reporting enabled on CPU#0.
[ 41.048316] Checking 'hlt' instruction... OK.
[ 41.075381] CPU0: AMD Athlon(tm) MP 2400+ stepping 01
[ 41.090713] Booting processor 1/0 eip 2000
[ 41.103013] CPU 1 irqstacks, hard=c14ae000 soft=c14b0000
[ 41.129111] Initializing CPU#1
[ 41.209490] Calibrating delay using timer specific routine.. 4000.21 BogoMIPS (lpj=8000422)
[ 41.209501] CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 41.209506] CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
[ 41.209514] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 41.209517] CPU: L2 Cache: 256K (64 bytes/line)
[ 41.209519] CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
[ 41.209524] Intel machine check architecture supported.
[ 41.209527] Intel machine check reporting enabled on CPU#1.
[ 41.209691] CPU1: AMD Athlon(tm) Processor stepping 01
[ 41.326644] Total of 2 processors activated (8008.22 BogoMIPS).
[ 41.344517] ENABLING IO-APIC IRQs
[ 41.354668] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
[ 41.516925] checking TSC synchronization across 2 CPUs: passed.
[ 0.004549] Brought up 2 CPUs
[ 0.117881] migration_cost=634
[ 0.127875] NET: Registered protocol family 16
[ 0.141425] PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2
[ 0.160475] PCI: Using configuration type 1
[ 0.173131] mtrr: your CPUs had inconsistent fixed MTRR settings
[ 0.191151] mtrr: probably your BIOS does not setup all CPUs.
[ 0.208359] mtrr: corrected configuration.
[ 0.221343] Generic PHY: Registered new driver
[ 0.234864] SCSI subsystem initialized
[ 0.246167] usbcore: registered new driver usbfs
[ 0.260084] usbcore: registered new driver hub
[ 0.273553] PCI: Probing PCI hardware
[ 0.284538] PCI: Probing PCI hardware (bus 00)
[ 0.284906] Boot video device is 0000:01:05.0
[ 0.285835] PCI->APIC IRQ transform: 0000:00:09.0[A] -> IRQ 17
[ 0.303331] PCI->APIC IRQ transform: 0000:01:05.0[A] -> IRQ 18
[ 0.320815] PCI->APIC IRQ transform: 0000:02:00.0[D] -> IRQ 19
[ 0.338297] PCI->APIC IRQ transform: 0000:02:06.0[A] -> IRQ 18
[ 0.355786] PCI->APIC IRQ transform: 0000:02:08.0[A] -> IRQ 19
[ 0.376031] irda_init()
[ 0.376062] NET: Registered protocol family 23
[ 0.389407] Bluetooth: Core ver 2.8
[ 0.399878] NET: Registered protocol family 31
[ 0.413201] Bluetooth: HCI device and connection manager initialized
[ 0.432235] Bluetooth: HCI socket layer initialized
[ 0.448213] PCI: Bridge: 0000:00:01.0
[ 0.459216] IO window: 2000-2fff
[ 0.469446] MEM window: e2100000-e21fffff
[ 0.481984] PREFETCH window: e8000000-f7ffffff
[ 0.495815] PCI: Bridge: 0000:00:10.0
[ 0.506814] IO window: 3000-3fff
[ 0.517012] MEM window: e2200000-e22fffff
[ 0.529542] PREFETCH window: 50000000-500fffff
[ 0.543469] Machine check exception polling timer started.
[ 0.562107] highmem bounce pool size: 64 pages
[ 0.575963] fuse init (API version 7.6)
[ 0.587618] Initializing Cryptographic API
[ 0.599956] io scheduler noop registered
[ 0.611854] io scheduler anticipatory registered (default)
[ 0.628474] io scheduler deadline registered
[ 0.641365] io scheduler cfq registered
[ 0.652937] BIOS failed to enable PCI standards compliance, fixing this error.
[ 0.889141] lp: driver loaded but no devices found
[ 0.903611] Real Time Clock Driver v1.12ac
[ 0.915936] hw_random: AMD768 system management I/O registers at 0x8000.
[ 0.936197] hw_random hardware driver 1.0.0 loaded
[ 0.950578] Linux agpgart interface v0.101 (c) Dave Jones
[ 0.966834] agpgart: Detected AMD 760MP chipset
[ 0.990511] agpgart: AGP aperture is 64M @ 0xe4000000
[ 1.007501] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.022721] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.037605] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 1.061215] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.079387] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.097855] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
[ 1.117361] parport0: irq 7 detected
[ 1.222368] lp0: using parport0 (polling).
[ 1.234881] Floppy drive(s): fd0 is 1.44M
[ 1.265993] FDC 0 is a post-1991 82077
[ 1.278682] loop: loaded (max 8 devices)
[ 1.290617] 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
[ 1.312261] 0000:02:08.0: 3Com PCI 3c905C Tornado at f8838000. Vers LK1.1.19
[ 1.355185] skge 1.3 addr 0xe2000000 irq 17 chip Yukon rev 1
[ 1.372246] skge eth1: addr 00:11:95:ff:2b:bd
[ 1.385379] Marvell 88E1101: Registered new driver
[ 1.399796] Davicom DM9161E: Registered new driver
[ 1.414220] Davicom DM9131: Registered new driver
[ 1.428385] Cicada Cis8204: Registered new driver
[ 1.442551] LXT970: Registered new driver
[ 1.454641] LXT971: Registered new driver
[ 1.466731] QS6612: Registered new driver
[ 1.478872] irda_register_dongle : registering dongle "JetEye PC ESI-9680 PC" (1).
[ 1.478876] irda_register_dongle : registering dongle "Tekram IR-210B" (0).
[ 1.478879] irda_register_dongle : registering dongle "Actisys ACT-220L" (2).
[ 1.478882] irda_register_dongle : registering dongle "Actisys ACT-220L+" (3).
[ 1.478884] irda_register_dongle : registering dongle "ACTiSYS ACT-IR200L" (10).
[ 1.478887] Linux video capture interface: v1.00
[ 1.492759] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.511812] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.535836] AMD7441: IDE controller at PCI slot 0000:00:07.1
[ 1.552805] AMD7441: chipset revision 4
[ 1.564322] AMD7441: not 100% native mode: will probe irqs later
[ 1.582339] AMD7441: 0000:00:07.1 (rev 04) UDMA100 controller
[ 1.599565] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
[ 1.621362] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 1.643156] Probing IDE interface ide0...
[ 1.929094] hda: ST380021A, ATA DISK drive
[ 2.612213] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 2.625928] Probing IDE interface ide1...
[ 3.358454] hdc: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
[ 4.156981] hdd: JLMS XJ-HD165H, ATAPI CD/DVD-ROM drive
[ 4.230134] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.244078] hda: max request size: 128KiB
[ 4.256705] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 4.281480] hda: cache flushes not supported
[ 4.294363] hda: hda1 hda2 hda3 hda4
[ 4.320215] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 4.343491] Uniform CD-ROM driver Revision: 3.20
[ 4.365391] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
[ 4.384540] st: Version 20050830, fixed bufsize 32768, s/g segs 256
[ 4.403523] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 4.403603] ohci_hcd 0000:02:00.0: OHCI Host Controller
[ 4.419371] ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
[ 4.441543] ohci_hcd 0000:02:00.0: irq 19, io mem 0xe2200000
[ 4.514336] usb usb1: configuration #1 chosen from 1 choice
[ 4.531108] hub 1-0:1.0: USB hub found
[ 4.542373] hub 1-0:1.0: 4 ports detected
[ 4.656050] Initializing USB Mass Storage driver...
[ 4.911485] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 5.096050] usb 1-1: configuration #1 chosen from 1 choice
[ 5.117038] hub 1-1:1.0: USB hub found
[ 5.129963] hub 1-1:1.0: 4 ports detected
[ 5.480233] usb 1-1.4: new full speed USB device using ohci_hcd and address 3
[ 5.687805] usb 1-1.4: configuration #1 chosen from 1 choice
[ 5.708978] usbcore: registered new driver usb-storage
[ 5.724401] USB Mass Storage support registered.
[ 5.738304] usbcore: registered new driver hiddev
[ 5.752474] usbcore: registered new driver usbhid
[ 5.766586] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 5.785194] usbcore: registered new driver usbserial
[ 5.800081] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 5.818916] drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan - (without firmware)
[ 5.848131] drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 1 port adapter
[ 5.875788] drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 2 port adapter
[ 5.903448] drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 4 port adapter
[ 5.931106] usbcore: registered new driver keyspan
[ 5.945482] drivers/usb/serial/keyspan.c: v1.1.4:Keyspan USB to Serial Converter Driver
[ 5.969494] usbcore: registered new driver phidgetkit
[ 5.984670] usbcore: registered new driver phidgetservo
[ 6.000428] mice: PS/2 mouse device common for all mice
[ 6.043917] input: AT Translated Set 2 keyboard as /class/input/input0
[ 6.063910] input: PC Speaker as /class/input/input1
[ 6.078862] i2c /dev entries driver
[ 6.089566] Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
[ 6.726801] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[ 7.431275] ALSA device list:
[ 7.440201] #0: Ensoniq AudioPCI ENS1371 at 0x3080, irq 18
[ 7.457284] NET: Registered protocol family 2
[ 7.506785] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 7.528893] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 7.555887] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 7.576954] TCP: Hash tables configured (established 262144 bind 65536)
[ 7.596785] TCP reno registered
[ 7.606258] TCP bic registered
[ 7.615418] TCP westwood registered
[ 7.625935] NET: Registered protocol family 1
[ 7.639073] NET: Registered protocol family 10
[ 7.652590] IPv6 over IPv4 tunneling driver
[ 7.665283] NET: Registered protocol family 17
[ 7.678723] IrCOMM protocol (Dag Brattli)
[ 7.692366] Bluetooth: L2CAP ver 2.8
[ 7.703100] Bluetooth: L2CAP socket layer initialized
[ 7.718255] Bluetooth: SCO (Voice Link) ver 0.5
[ 7.731838] Bluetooth: SCO socket layer initialized
[ 7.746484] Bluetooth: RFCOMM socket layer initialized
[ 7.761895] Bluetooth: RFCOMM TTY layer initialized
[ 7.776528] Bluetooth: RFCOMM ver 1.7
[ 7.787528] Bluetooth: BNEP (Ethernet Emulation) ver 1.2
[ 7.803457] Bluetooth: BNEP filters: protocol multicast
[ 7.819129] Bluetooth: HIDP (Human Interface Emulation) ver 1.1
[ 7.858147] CCID: Registered CCID 3 (ccid3)
[ 7.896476] SCTP: Hash tables configured (established 65536 bind 65536)
[ 7.916432] Starting balanced_irq
[ 7.926402] Using IPI Shortcut mode
[ 7.936889] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 7.971740] VFS: Mounted root (ext2 filesystem) readonly.
[ 7.988347] Freeing unused kernel memory: 228k freed
[ 10.933325] Bluetooth: HCI USB driver ver 2.9
[ 10.948136] usbcore: registered new driver hci_usb
[ 12.807419] Adding 1999864k swap on /dev/hda2. Priority:-1 extents:1 across:1999864k
[ 161.386430] skge eth1: enabling interface
[ 161.404705] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 163.859927] skge eth1: Link is up at 1000 Mbps, full duplex, flow control tx and rx
[ 163.884967] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
^ permalink raw reply
* Re: [PATCH 5/6] myri10ge - Second half of the driver
From: Herbert Xu @ 2006-05-12 0:31 UTC (permalink / raw)
To: Brice Goglin; +Cc: shemminger, netdev, linux-kernel, gallatin
In-Reply-To: <4463CE71.1000205@myri.com>
Brice Goglin <brice@myri.com> wrote:
>
>> It is preferred to put function declarations on one line.
>>
>> static int mril10ge_open(struct net_device *dev)
>
> Well, I have seen several threads about this in the archive, with some
> people against and some people pro. I personaly like grepping for the
> declaration of function using ^name.
> If this codingstyle is really required, I will do.
Yes this is the standard coding style used in Linux so please do.
Thanks,
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt
^ permalink raw reply
* Re: [PATCH 4/6] myri10ge - First half of the driver
From: Brice Goglin @ 2006-05-11 23:53 UTC (permalink / raw)
To: Francois Romieu; +Cc: netdev, LKML, Andrew J. Gallatin
In-Reply-To: <20060510231347.GC25334@electric-eye.fr.zoreil.com>
Francois Romieu wrote:
>
>> + spin_lock(&mgp->cmd_lock);
>> + response->result = 0xffffffff;
>> + mb();
>> + myri10ge_pio_copy((void __iomem *) cmd_addr, buf, sizeof (*buf));
>> +
>> + /* wait up to 2 seconds */
>>
>
> You must not hold a spinlock for up to 2 seconds.
>
We are working on reducing the delay to about 15ms. It only occurs when
the driver is loaded or the link brought up.
>> + for (sleep_total = 0; sleep_total < (2 * 1000); sleep_total += 10) {
>> + mb();
>> + if (response->result != 0xffffffff) {
>> + if (response->result == 0) {
>> + data->data0 = ntohl(response->data);
>> + spin_unlock(&mgp->cmd_lock);
>> + return 0;
>> + } else {
>> + dev_err(&mgp->pdev->dev,
>> + "command %d failed, result = %d\n",
>> + cmd, ntohl(response->result));
>> + spin_unlock(&mgp->cmd_lock);
>> + return -ENXIO;
>>
>
> Return in a middle of a spinlock-intensive function. :o(
>
What do you mean ?
>
>> +{
>> + struct sk_buff *skb;
>> + unsigned long data, roundup;
>> +
>> + skb = dev_alloc_skb(bytes + 4096 + MYRI10GE_MCP_ETHER_PAD);
>> + if (skb == NULL)
>> + return NULL;
>>
>
> Imho you will want to work directly with pages shortly.
>
We had thought about doing this, but were a little nervous since we did
not know of any other drivers that worked directly with pages. If this
is an official direction to work directly with pages, we will. But the
existing approach is well tested through our beta cycle, and we would
prefer to leave it as is and update to a pages based approach in the
future.
Thanks a lot for all the comments.
Brice
^ permalink raw reply
* Re: [PATCH 5/6] myri10ge - Second half of the driver
From: Brice Goglin @ 2006-05-11 23:53 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: netdev, LKML, Andrew J. Gallatin
In-Reply-To: <20060510152244.44fb3db7@localhost.localdomain>
Stephen Hemminger wrote:
>> +
>> +static int
>> +myri10ge_open(struct net_device *dev)
>>
>
> It is preferred to put function declarations on one line.
>
> static int mril10ge_open(struct net_device *dev)
>
Well, I have seen several threads about this in the archive, with some
people against and some people pro. I personaly like grepping for the
declaration of function using ^name.
If this codingstyle is really required, I will do.
> I would prefer to just have driver always do NAPI. It's a 10G driver, it
> really needs to be NAPI to prevent machine starvation.
>
When TSO is disabled, we see performance being about 300Mbs lower when
enabling NAPI. But we'll probably enable TSO by default (see below) so
we'll probably drop non-NAPI.
>> + myri10ge_close(mgp->dev);
>> + status = myri10ge_load_firmware(mgp);
>> + if (status != 0) {
>> + printk(KERN_ERR "myri10ge: %s: failed to load firmware\n",
>> + mgp->dev->name);
>> + return;
>> + }
>> + myri10ge_open(mgp->dev);
>> +}
>>
>
> Watchdog's are a sign of buggy hardware and drivers!
>
Well... the watchdog is supposed to help detecting memory parity errors
in the NIC. It's rare, but it happens with cosmic rays. The recovery
part still need some work anyway. So we might drop the watchdog for now
and come back when recovery is ready.
Additionally, we are using our own watchdog because the linux netdev
watchdog does not seem to work well for devices with large hardware
transmit queues. If there is a hardware problem, a single (or even a
handful) of TCP streams will not backup into the hardware queue in a
timely fashion, leading to a long delay before the netdev watchdog
routine is called.
>> +#if 0
>> + /* TSO can be enabled via ethtool -K eth1 tso on */
>> +#ifdef NETIF_F_TSO
>> + netdev->features |= NETIF_F_TSO;
>> +#endif
>> +#endif
>>
>
> If it works enable it, if it doesn't take the code out.
>
It works. We did not enable it by default because there were some
problems in older kernels. They seem to be fixed in recent kernels. So
we'll enable TSO by default and have people disable it if it causes
problems.
>> [PATCH 3/6] myri10ge - Driver header files
>>
>> myri10ge driver header files.
>> myri10ge_mcp.h is the generic header, while myri10ge_mcp_gen_header.h
>> is automatically generated from our firmware image.
>>
>
> Then clean it up after the auto generation.
> Auto generated code still gets maintained by humans.
>
Oops sorry, I forgot to apply my cleaning script before sending.
>> +#define MYRI10GE_MCP_MAJOR 1
>> +#define MYRI10GE_MCP_MINOR 4
>> +
>>
>
> Major/Minor for what. You don't have a character device.
>
That's the firmware version, we'll find better names.
Thanks a lot for all the comments.
Brice
^ permalink raw reply
* Re: [PATCH 4/6] myri10ge - First half of the driver
From: Brice Goglin @ 2006-05-11 23:53 UTC (permalink / raw)
To: Roland Dreier; +Cc: netdev, LKML, Andrew J. Gallatin
In-Reply-To: <adahd3x7d0b.fsf@cisco.com>
Roland Dreier wrote:
> > +#define myri10ge_pio_copy(to,from,size) __iowrite64_copy(to,from,size/8)
>
> Why do you need this wrapper? Why not just call __iowrite64_copy()
> without the obfuscation? Anyone reading the code will just have to
> search back to this define and mentally translate the size back and
> forth all the time.
>
Well, I know that abstraction layer is bad. But in this case I really
think that a name like myri10ge_pio_copy(size) is way less obfuscating
than __iowrite64_copy(size/8).
Will fix it if it really matters.
> > +int myri10ge_hyper_msi_cap_on(struct pci_dev *pdev)
> > +{
> > + uint8_t cap_off;
> > + int nbcap = 0;
> > +
> > + cap_off = PCI_CAPABILITY_LIST - 1;
> > + /* go through all caps looking for a hypertransport msi mapping */
>
> This looks like something that should be fixed up in the general PCI
> quirk handling rather than in every driver...
>
> > +static int
> > +myri10ge_use_msi(struct pci_dev *pdev)
> > +{
> > + if (myri10ge_msi == 1 || myri10ge_msi == 0)
> > + return myri10ge_msi;
> > +
> > + /* find root complex for our device */
> > + while (pdev->bus && pdev->bus->self) {
> > + pdev = pdev->bus->self;
> > + }
>
> Similarly looks like generic PCI code (if it's needed at all). If I
> understand correctly you're trying to check if MSI has a chance at
> working on the system, but a network device driver has no business
> walking up the PCI hierarchy.
>
Right, I will look at moving all this to the core PCI code.
Thanks for all the comments.
Brice
^ permalink raw reply
* [PATCH] sky2: prevent dual port receiver problems
From: Stephen Hemminger @ 2006-05-11 22:07 UTC (permalink / raw)
To: netdev
When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.
It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
--- sky2.orig/drivers/net/sky2.c
+++ sky2/drivers/net/sky2.c
@@ -1020,8 +1020,19 @@ static int sky2_up(struct net_device *de
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u32 ramsize, rxspace, imask;
- int err = -ENOMEM;
+ int err;
+ struct net_device *otherdev = hw->dev[sky2->port^1];
+ /* Block bringing up both ports at the same time on a dual port card.
+ * There is an unfixed bug where receiver gets confused and picks up
+ * packets out of order. Until this is fixed, prevent data corruption.
+ */
+ if (otherdev && netif_running(otherdev)) {
+ printk(KERN_INFO PFX "dual port support is disabled.\n");
+ return -EBUSY;
+ }
+
+ err = -ENOMEM;
if (netif_msg_ifup(sky2))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
^ permalink raw reply
* Re: [PATCH wireless-dev] d80211: Don't discriminate against 802.11b drivers
From: Michael Wu @ 2006-05-10 17:31 UTC (permalink / raw)
To: Jiri Benc; +Cc: John W. Linville, Jouni Malinen, netdev, jkmaline
In-Reply-To: <20060511175426.72ae7744@griffin.suse.cz>
On Thursday 11 May 2006 11:54, Jiri Benc wrote:
> On Thu, 4 May 2006 22:32:35 -0400, Michael Wu wrote:
> > This makes the current hack used to prevent 802.11g cards from scanning
> > with 802.11b channels not break scanning in 802.11b drivers.
>
> I think this should be better:
>
I think this is overkill to fix a hack. IMHO, scan_skip_11b shouldn't exist in
the first place. One alternative would be to modify 802.11g drivers to not
set IEEE80211_CHAN_W_SCAN on 802.11b channels when there are equivalent
802.11g channels. Another would be to set the local->hw_modes bitfield
correctly during driver initialization instead of relying on userspace to set
it, so the existing logic for avoiding 802.11b channels when 802.11g is
supported actually works.
Hmm... that ioctl for changing the hw_modes bitfield doesn't seem too good..
No validity checking at all .. but then again, the current value of hw_modes
isn't valid to begin with. It seems like hw_modes is more useful for saying
what modes shouldn't be used than saying what modes are supported by the
hardware and should be used.
-Michael Wu
^ permalink raw reply
* Re: [PATCH wireless-dev] d80211: Don't discriminate against 802.11b drivers
From: Michael Buesch @ 2006-05-11 20:41 UTC (permalink / raw)
To: Jiri Benc; +Cc: John W. Linville, Jouni Malinen, netdev, jkmaline, Michael Wu
In-Reply-To: <20060511175426.72ae7744@griffin.suse.cz>
On Thursday 11 May 2006 17:54, you wrote:
> On Thu, 4 May 2006 22:32:35 -0400, Michael Wu wrote:
> > This makes the current hack used to prevent 802.11g cards from scanning with
> > 802.11b channels not break scanning in 802.11b drivers.
>
> I think this should be better:
>
> Signed-off-by: Jiri Benc <jbenc@suse.cz>
>
> ---
>
> net/d80211/ieee80211.c | 14 ++++++++++++++
> net/d80211/ieee80211_sta.c | 1 -
> 2 files changed, 14 insertions(+), 1 deletion(-)
>
> --- dscape.orig/net/d80211/ieee80211.c
> +++ dscape/net/d80211/ieee80211.c
> @@ -4014,6 +4014,19 @@ static void ieee80211_precalc_rates(stru
> }
> }
>
> +static inline void ieee80211_apply_modes(struct ieee80211_hw *hw,
> + struct ieee80211_local *local)
Just a minor nitpick, but please remove the "inline".
This is a candidate for binary bloat, if it is called later
on another place, too, and modern compilers will inline it anyway, if
only used once.
Additionally it is not a hotpath.
> +{
> + struct ieee80211_hw_modes *mode;
> + int i;
> +
> + local->scan_skip_11b = 0;
> + for (i = 0; i < hw->num_modes; i++) {
> + mode = &hw->modes[i];
> + if (mode->mode == MODE_IEEE80211G)
> + local->scan_skip_11b = 1;
> + }
> +}
>
> struct net_device *ieee80211_alloc_hw(size_t priv_data_len,
> void (*setup)(struct net_device *))
> @@ -4258,6 +4271,7 @@ int ieee80211_update_hw(struct net_devic
> return -1;
>
> ieee80211_precalc_rates(hw);
> + ieee80211_apply_modes(hw, local);
> local->conf.phymode = hw->modes[0].mode;
> local->curr_rates = hw->modes[0].rates;
> local->num_curr_rates = hw->modes[0].num_rates;
> --- dscape.orig/net/d80211/ieee80211_sta.c
> +++ dscape/net/d80211/ieee80211_sta.c
> @@ -2566,7 +2566,6 @@ int ieee80211_sta_req_scan(struct net_de
> memcpy(local->scan_ssid, ssid, ssid_len);
> } else
> local->scan_ssid_len = 0;
> - local->scan_skip_11b = 1; /* FIX: clear this is 11g is not supported */
> local->scan_state = SCAN_SET_CHANNEL;
> local->scan_hw_mode_idx = 0;
> local->scan_channel_idx = 0;
>
>
--
Greetings Michael.
^ permalink raw reply
* Re: Initial benchmarks of some VJ ideas [mmap memcpy vs copy_to_user].
From: Rick Jones @ 2006-05-11 19:30 UTC (permalink / raw)
To: David S. Miller; +Cc: johnpol, netdev, caitlinb, kelly, rusty
In-Reply-To: <20060511.115409.89709859.davem@davemloft.net>
David S. Miller wrote:
> From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
> Date: Thu, 11 May 2006 20:18:15 +0400
>
>
>>Here is profile result:
>>1463625 78.0003 poll_idle
>>19171 1.0217 _spin_lock_irqsave
>>15887 0.8467 _read_lock
>>14712 0.7840 kfree
>>13370 0.7125 ip_frag_queue
>>11896 0.6340 delay_pmtmr
>>11811 0.6294 _spin_lock
>>11723 0.6247 csum_partial
>>11399 0.6075 ip_frag_destroy
>>11063 0.5896 serial_in
>>10533 0.5613 skb_release_data
>>10524 0.5609 ip_route_input
>>10319 0.5499 __alloc_skb
>
>
> Too bad spinlocks are not inlined any longer, this makes oprofile
> output so much less useful.
But it is nice to see how much time is being spent in "locking"
rick jones
^ permalink raw reply
* Re: [PATCH] dl2k: use explicit DMA_48BIT_MASK
From: Francois Romieu @ 2006-05-11 19:23 UTC (permalink / raw)
Cc: Daniel Walker, akpm, edward_peng, netdev, linux-kernel
In-Reply-To: <20060510235215.GC26617@us.ibm.com>
Jon Mason <jdmason@us.ibm.com> :
[...]
> DMA_*BIT_MASK is intended to be used in the DMA_API's checking of
> DMA controller's addressable memory, where as this is masking off the
> lower 48bits of a descriptor for its DMA address.
Imho it's the specific reason why the DMA_*BIT_MASK applies here: the
code is already in dma-"tainted" land.
> I think a better solution (which I should've done when I pushed the
> original patch) would be a driver specific #define.
$ find drivers -type f | xargs grep -i [^f]ffffffffffff[^f] | wc -l
12
No disagreement: it does not have a huge potential for code duplication.
--
Ueimor
^ permalink raw reply
* Re: [NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
From: David S. Miller @ 2006-05-11 19:22 UTC (permalink / raw)
To: kaber; +Cc: netdev
In-Reply-To: <44635082.7000701@trash.net>
This patch looks fine, applied.
Thanks a lot Patrick.
^ permalink raw reply
* Re: Initial benchmarks of some VJ ideas [mmap memcpy vs copy_to_user].
From: David S. Miller @ 2006-05-11 18:54 UTC (permalink / raw)
To: johnpol; +Cc: netdev, caitlinb, kelly, rusty
In-Reply-To: <20060511161815.GA623@2ka.mipt.ru>
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Date: Thu, 11 May 2006 20:18:15 +0400
> Here is profile result:
> 1463625 78.0003 poll_idle
> 19171 1.0217 _spin_lock_irqsave
> 15887 0.8467 _read_lock
> 14712 0.7840 kfree
> 13370 0.7125 ip_frag_queue
> 11896 0.6340 delay_pmtmr
> 11811 0.6294 _spin_lock
> 11723 0.6247 csum_partial
> 11399 0.6075 ip_frag_destroy
> 11063 0.5896 serial_in
> 10533 0.5613 skb_release_data
> 10524 0.5609 ip_route_input
> 10319 0.5499 __alloc_skb
Too bad spinlocks are not inlined any longer, this makes oprofile
output so much less useful.
Also, since you test UDP with >MTU sized sends, you add fragmentation
into the mix, yet another variable that you won't see with TCP :-)
BTW you make another massively critical error in your analysis of TCP
profiles.
You mention that "tcp_v4_rcv()" shows up in your profiles and not
__inet_lookup(). This __inet_lookup() is inlined, and thus it's cost
shows up as "tcp_v4_rcv()". I find such oversight amazing for someone
as careful about details as you are :-)
I would suggest to look at instruction level profile hits, it makes
such mistakes in analysis almost impossible :-)
^ permalink raw reply
* Re: [PATCH] expose simplified skb_checksum_recalc
From: Ingo Oeser @ 2006-05-11 18:40 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: David S. Miller, Ingo Oeser, netdev
In-Reply-To: <20060511112843.6532bddd@localhost.localdomain>
Hi Stephen,
Stephen Hemminger wrote:
> Many users of skb_checksum_help() are just using it to recalculate
> outbound checksum, so why not expose the interface in a more useful
> way. Suggested by Ingo Oeser.
You are damn fast Stephen :-)
That's even better and improves a lot on documentation and
code placement for free.
Thanks & Regards
Ingo Oeser
^ permalink raw reply
* [PATCH] expose simplified skb_checksum_recalc
From: Stephen Hemminger @ 2006-05-11 18:28 UTC (permalink / raw)
To: Ingo Oeser, David S. Miller; +Cc: Ingo Oeser, netdev
In-Reply-To: <200605111924.33125.netdev@axxeo.de>
Many users of skb_checksum_help() are just using it to recalculate
outbound checksum, so why not expose the interface in a more useful
way. Suggested by Ingo Oeser.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
--- linux-2.6.orig/include/linux/skbuff.h 2006-04-27 11:12:53.000000000 -0700
+++ linux-2.6/include/linux/skbuff.h 2006-05-11 11:17:39.000000000 -0700
@@ -1343,6 +1343,24 @@
__skb_checksum_complete(skb);
}
+extern int skb_checksum_recalc(struct sk_buff *skb);
+/**
+ * skb_checksum_help - recalculate checksum of packet
+ * @skb: packet to process
+ * @inward: direction of flow, zero is receiving
+ *
+ * Invalidate hardware checksum when packet is to be mangled on
+ * receive and complete checksum manually on outgoing path.
+ */
+static inline int skb_checksum_help(struct sk_buff *skb, int inward)
+{
+ if (inward) {
+ skb->ip_summed = CHECKSUM_NONE;
+ return 0;
+ }
+ return skb_checksum_recalc(skb);
+}
+
#ifdef CONFIG_NETFILTER
static inline void nf_conntrack_put(struct nf_conntrack *nfct)
{
--- sky2.orig/net/core/dev.c 2006-05-10 10:17:51.000000000 -0700
+++ sky2/net/core/dev.c 2006-05-11 11:22:27.000000000 -0700
@@ -1144,39 +1144,6 @@
EXPORT_SYMBOL(netif_device_attach);
-/*
- * Invalidate hardware checksum when packet is to be mangled, and
- * complete checksum manually on outgoing path.
- */
-int skb_checksum_help(struct sk_buff *skb, int inward)
-{
- unsigned int csum;
- int ret = 0, offset = skb->h.raw - skb->data;
-
- if (inward) {
- skb->ip_summed = CHECKSUM_NONE;
- goto out;
- }
-
- if (skb_cloned(skb)) {
- ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
- if (ret)
- goto out;
- }
-
- BUG_ON(offset > (int)skb->len);
- csum = skb_checksum(skb, offset, skb->len-offset, 0);
-
- offset = skb->tail - skb->h.raw;
- BUG_ON(offset <= 0);
- BUG_ON(skb->csum + 2 > offset);
-
- *(u16*)(skb->h.raw + skb->csum) = csum_fold(csum);
- skb->ip_summed = CHECKSUM_NONE;
-out:
- return ret;
-}
-
/* Take action when hardware reception checksum errors are detected. */
#ifdef CONFIG_BUG
void netdev_rx_csum_fault(struct net_device *dev)
@@ -3403,7 +3370,6 @@
EXPORT_SYMBOL(register_gifconf);
EXPORT_SYMBOL(register_netdevice);
EXPORT_SYMBOL(register_netdevice_notifier);
-EXPORT_SYMBOL(skb_checksum_help);
EXPORT_SYMBOL(synchronize_net);
EXPORT_SYMBOL(unregister_netdevice);
EXPORT_SYMBOL(unregister_netdevice_notifier);
--- sky2.orig/net/core/skbuff.c 2006-04-27 11:12:54.000000000 -0700
+++ sky2/net/core/skbuff.c 2006-05-11 11:23:13.000000000 -0700
@@ -1334,6 +1334,36 @@
}
/**
+ * skb_checksum_recalc - force software checksum
+ * @skb: skb to process
+ * Force complete checksum, this is used to force a software checksum
+ * on the outgoing path.
+ */
+int skb_checksum_recalc(struct sk_buff *skb)
+{
+ unsigned int csum;
+ int ret = 0, offset = skb->h.raw - skb->data;
+
+ if (skb_cloned(skb)) {
+ ret = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (ret)
+ goto out;
+ }
+
+ BUG_ON(offset > (int)skb->len);
+ csum = skb_checksum(skb, offset, skb->len-offset, 0);
+
+ offset = skb->tail - skb->h.raw;
+ BUG_ON(offset <= 0);
+ BUG_ON(skb->csum + 2 > offset);
+
+ *(u16*)(skb->h.raw + skb->csum) = csum_fold(csum);
+ skb->ip_summed = CHECKSUM_NONE;
+out:
+ return ret;
+}
+
+/**
* skb_dequeue - remove from the head of the queue
* @list: list to dequeue from
*
@@ -1854,6 +1884,7 @@
EXPORT_SYMBOL(pskb_copy);
EXPORT_SYMBOL(pskb_expand_head);
EXPORT_SYMBOL(skb_checksum);
+EXPORT_SYMBOL(skb_checksum_recalc);
EXPORT_SYMBOL(skb_clone);
EXPORT_SYMBOL(skb_clone_fraglist);
EXPORT_SYMBOL(skb_copy);
^ permalink raw reply
* Re: [RFC PATCH 34/35] Add the Xen virtual network device driver.
From: Andi Kleen @ 2006-05-11 17:30 UTC (permalink / raw)
To: Rick Jones
Cc: xen-devel, tytso, Herbert Xu, virtualization, netdev, rdreier,
linux-kernel, chrisw, ian.pratt, shemminger
In-Reply-To: <44636ACB.4020705@hp.com>
On Thursday 11 May 2006 18:48, Rick Jones wrote:
> From the peanut gallery...
>
> Can remote TCP ISN's be considered a source of entropy these days? How
> about checksums?
Indirectly - we measure how long it takes to compute them.
-Andi
^ permalink raw reply
* Re: [RFC PATCH 34/35] Add the Xen virtual network device driver.
From: Rick Jones @ 2006-05-11 16:48 UTC (permalink / raw)
To: Andi Kleen
Cc: Keir Fraser, tytso, Herbert Xu, xen-devel, ian.pratt, rdreier,
linux-kernel, netdev, virtualization, chrisw, shemminger
In-Reply-To: <200605111147.53011.ak@suse.de>
From the peanut gallery...
Can remote TCP ISN's be considered a source of entropy these days? How
about checksums?
rick
^ permalink raw reply
* [PATCH] neighbour.c, pneigh_get_next() skips published entry
From: Jari Takkala @ 2006-05-11 16:29 UTC (permalink / raw)
To: linux-kernel; +Cc: netdev
The following patch fixes a problem where output from /proc/net/arp
skips a record when the full output does not fit into the users read()
buffer.
To reproduce: publish a large number of ARP entries (more than 10
required on my system). Run 'dd if=/proc/net/arp of=arp-1024.out
bs=1024'. View the output, one entry will be missing.
Please review and commit if acceptable.
Signed-off-by: Jari Takkala <jari.takkala@q9.com>
--- linux-2.6.16.15.orig/net/core/neighbour.c 2006-05-09
15:53:30.000000000 -0400
+++ linux-2.6.16.15/net/core/neighbour.c 2006-05-10
16:06:40.000000000 -0400
@@ -2120,6 +2120,11 @@
struct neigh_seq_state *state = seq->private;
struct neigh_table *tbl = state->tbl;
+ if (pos != NULL && *pos == 1 && (pn->next ||
tbl->phash_buckets[state->bucket])) {
+ --(*pos);
+ return pn;
+ }
+
pn = pn->next;
while (!pn) {
if (++state->bucket > PNEIGH_HASHMASK)
^ permalink raw reply
* Re: [RFC PATCH 34/35] Add the Xen virtual network device driver.
From: Stephen Hemminger @ 2006-05-11 16:18 UTC (permalink / raw)
To: Andi Kleen
Cc: xen-devel, tytso, Herbert Xu, virtualization, netdev, rdreier,
linux-kernel, chrisw, ian.pratt
In-Reply-To: <200605111147.53011.ak@suse.de>
On Thu, 11 May 2006 11:47:52 +0200
Andi Kleen <ak@suse.de> wrote:
> On Thursday 11 May 2006 09:49, Keir Fraser wrote:
> > On 11 May 2006, at 01:33, Herbert Xu wrote:
> > >> But if sampling virtual events for randomness is really unsafe (is it
> > >> really?) then native guests in Xen would also get bad random numbers
> > >> and this would need to be somehow addressed.
> > >
> > > Good point. I wonder what VMWare does in this situation.
> >
> > Well, there's not much they can do except maybe jitter interrupt
> > delivery. I doubt they do that though.
> >
> > The original complaint in our case was that we take entropy from
> > interrupts caused by other local VMs, as well as external sources.
> > There was a feeling that the former was more predictable and could form
> > the basis of an attack. I have to say I'm unconvinced: I don't really
> > see that it's significantly easier to inject precisely-timed interrupts
> > into a local VM. Certainly not to better than +/- a few microseconds.
> > As long as you add cycle-counter info to the entropy pool, the least
> > significant bits of that will always be noise.
>
> I think I agree - e.g. i would expect the virtual interrupts to have
> enough jitter too. Maybe it would be good if someone could
> run a few statistics on the resulting numbers?
>
> Ok the randomness added doesn't consist only of the least significant
> bits. Currently it adds jiffies+full 32bit cycle count. I guess if it was
> a real problem the code could be changed to leave out the jiffies and
> only add maybe a 8 bit word from the low bits. But that would only
> help for the para case because the algorithm for native guests
> cannot be changed.
>
> > 2. An entropy front/back is tricky -- how do we decide how much
> > entropy to pull from domain0? How much should domain0 be prepared to
> > give other domains? How easy is it to DoS domain0 by draining its
> > entropy pool? Yuk.
>
> I claim (without having read any code) that in theory you need to have solved
> that problem already in the vTPM @)
>
The base question under all this is "how good does an entropy source have
to be?" and then "what guarantees do we make about the entropy inputs used
by /dev/random?". If we can resolve those, then the virtual environment
answer should fall out.
This is a area where the security tin-foil hat types take over, and it
gets real hard to make "good enough" argument. People have built an expectation
that /dev/random has really strong entropy, good enough to generate long term
keys etc.
^ permalink raw reply
* Re: Initial benchmarks of some VJ ideas [mmap memcpy vs copy_to_user].
From: Evgeniy Polyakov @ 2006-05-11 16:18 UTC (permalink / raw)
To: David S. Miller; +Cc: netdev, caitlinb, kelly, rusty
In-Reply-To: <20060511083031.GA12712@2ka.mipt.ru>
On Thu, May 11, 2006 at 12:30:32PM +0400, Evgeniy Polyakov (johnpol@2ka.mipt.ru) wrote:
> On Thu, May 11, 2006 at 12:07:21AM -0700, David S. Miller (davem@davemloft.net) wrote:
> > You can test with single stream, but then you are only testing
> > in-cache case. Try several thousand sockets and real load from many
> > unique source systems, it becomes interesting then.
>
> I can test system with large number of streams, but unfortunately only
> from small number of different src/dst ip addresses, so I can not
> benchmark route lookup performance in layered design.
I've run it with 200 UDP sockets in receive path. There were two load
generator machines with 100 clients in each.
There are no copies of skb->data in recvmsg().
Since I only have 1Gb link I'm unable to provide each client with high
bandwith, so they send 4k chunks.
Performance dropped twice down to 55 MB/sec and CPU usage increased noticebly
(slow drift from 12 to 8% compared to 2% with one socket),
but it is not because of cache effect I believe,
but due to highly increased number of syscalls per second.
Here is profile result:
1463625 78.0003 poll_idle
19171 1.0217 _spin_lock_irqsave
15887 0.8467 _read_lock
14712 0.7840 kfree
13370 0.7125 ip_frag_queue
11896 0.6340 delay_pmtmr
11811 0.6294 _spin_lock
11723 0.6247 csum_partial
11399 0.6075 ip_frag_destroy
11063 0.5896 serial_in
10533 0.5613 skb_release_data
10524 0.5609 ip_route_input
10319 0.5499 __alloc_skb
9903 0.5278 ip_defrag
9889 0.5270 _read_unlock
9536 0.5082 _write_unlock
8639 0.4604 _write_lock
7557 0.4027 netif_receive_skb
6748 0.3596 ip_frag_intern
6534 0.3482 preempt_schedule
6220 0.3315 __kmalloc
6005 0.3200 schedule
5924 0.3157 irq_entries_start
5823 0.3103 _spin_unlock_irqrestore
5678 0.3026 ip_rcv
5410 0.2883 __kfree_skb
5056 0.2694 kmem_cache_alloc
5014 0.2672 kfree_skb
4900 0.2611 eth_type_trans
4067 0.2167 kmem_cache_free
3532 0.1882 udp_recvmsg
3531 0.1882 ip_frag_reasm
3331 0.1775 _read_lock_irqsave
3327 0.1773 ipq_kill
3304 0.1761 udp_v4_lookup_longway
I'm going to resurrect zero-copy sniffer project [1] and create special
socket option which would allow to insert pages, which contain
skb->data, into process VMA using VM remapping tricks. Unfortunately it
requires TLB flushing and probably there will be no significant
performance/CPU gain if any, but I think, it is the only way to provide receiving
zero-copy access to hardware which does not support header split.
Other idea, which I will try, if I understood you correctly, is to create unified cache.
I think some interesting results can be obtained from following
approach: in softint we do not process skb->data at all, but only get
src/dst/sport/dport/protocol numbers (it could require maximum two cache lines,
or it is not fast-path packet (but something like ipsec) and can be processed as usual)
and create some "initial" cache based on that data, skb is then queued into that
"initial" cache entry and recvmsg() in process context later process'
that entry.
Back to the drawing board...
Thanks for discussion.
1. zero-copy sniffer
http://tservice.net.ru/~s0mbre/old/?section=projects&item=af_tlb
--
Evgeniy Polyakov
^ permalink raw reply
* Re: [PATCH wireless-dev] d80211: Don't discriminate against 802.11b drivers
From: Jiri Benc @ 2006-05-11 15:54 UTC (permalink / raw)
To: Michael Wu; +Cc: John W. Linville, Jouni Malinen, netdev, jkmaline
In-Reply-To: <200605042232.35446.flamingice@sourmilk.net>
On Thu, 4 May 2006 22:32:35 -0400, Michael Wu wrote:
> This makes the current hack used to prevent 802.11g cards from scanning with
> 802.11b channels not break scanning in 802.11b drivers.
I think this should be better:
Signed-off-by: Jiri Benc <jbenc@suse.cz>
---
net/d80211/ieee80211.c | 14 ++++++++++++++
net/d80211/ieee80211_sta.c | 1 -
2 files changed, 14 insertions(+), 1 deletion(-)
--- dscape.orig/net/d80211/ieee80211.c
+++ dscape/net/d80211/ieee80211.c
@@ -4014,6 +4014,19 @@ static void ieee80211_precalc_rates(stru
}
}
+static inline void ieee80211_apply_modes(struct ieee80211_hw *hw,
+ struct ieee80211_local *local)
+{
+ struct ieee80211_hw_modes *mode;
+ int i;
+
+ local->scan_skip_11b = 0;
+ for (i = 0; i < hw->num_modes; i++) {
+ mode = &hw->modes[i];
+ if (mode->mode == MODE_IEEE80211G)
+ local->scan_skip_11b = 1;
+ }
+}
struct net_device *ieee80211_alloc_hw(size_t priv_data_len,
void (*setup)(struct net_device *))
@@ -4258,6 +4271,7 @@ int ieee80211_update_hw(struct net_devic
return -1;
ieee80211_precalc_rates(hw);
+ ieee80211_apply_modes(hw, local);
local->conf.phymode = hw->modes[0].mode;
local->curr_rates = hw->modes[0].rates;
local->num_curr_rates = hw->modes[0].num_rates;
--- dscape.orig/net/d80211/ieee80211_sta.c
+++ dscape/net/d80211/ieee80211_sta.c
@@ -2566,7 +2566,6 @@ int ieee80211_sta_req_scan(struct net_de
memcpy(local->scan_ssid, ssid, ssid_len);
} else
local->scan_ssid_len = 0;
- local->scan_skip_11b = 1; /* FIX: clear this is 11g is not supported */
local->scan_state = SCAN_SET_CHANNEL;
local->scan_hw_mode_idx = 0;
local->scan_channel_idx = 0;
--
Jiri Benc
SUSE Labs
^ permalink raw reply
* [PATCH] rt2x00: fix oops in config_interface
From: Jiri Benc @ 2006-05-11 15:06 UTC (permalink / raw)
To: John W. Linville; +Cc: Ivo van Doorn, NetDev
BSSID passed to config_interface callback is NULL in modes other than STA or
IBSS.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
---
drivers/net/wireless/d80211/rt2x00/rt2400pci.c | 3 ++-
drivers/net/wireless/d80211/rt2x00/rt2500pci.c | 3 ++-
drivers/net/wireless/d80211/rt2x00/rt2500usb.c | 3 ++-
drivers/net/wireless/d80211/rt2x00/rt61pci.c | 3 ++-
drivers/net/wireless/d80211/rt2x00/rt73usb.c | 3 ++-
5 files changed, 10 insertions(+), 5 deletions(-)
--- dscape.orig/drivers/net/wireless/d80211/rt2x00/rt2400pci.c
+++ dscape/drivers/net/wireless/d80211/rt2x00/rt2400pci.c
@@ -1848,7 +1848,8 @@ rt2400pci_config_interface(struct net_de
if (rt2x00pci->type == IEEE80211_IF_TYPE_MNTR)
return 0;
- rt2400pci_config_bssid(rt2x00pci, conf->bssid);
+ if (conf->bssid)
+ rt2400pci_config_bssid(rt2x00pci, conf->bssid);
return 0;
}
--- dscape.orig/drivers/net/wireless/d80211/rt2x00/rt2500pci.c
+++ dscape/drivers/net/wireless/d80211/rt2x00/rt2500pci.c
@@ -1971,7 +1971,8 @@ rt2500pci_config_interface(struct net_de
if (conf->type == IEEE80211_IF_TYPE_MNTR)
return 0;
- rt2500pci_config_bssid(rt2x00pci, conf->bssid);
+ if (conf->bssid)
+ rt2500pci_config_bssid(rt2x00pci, conf->bssid);
return 0;
}
--- dscape.orig/drivers/net/wireless/d80211/rt2x00/rt2500usb.c
+++ dscape/drivers/net/wireless/d80211/rt2x00/rt2500usb.c
@@ -1636,7 +1636,8 @@ rt2500usb_config_interface(struct net_de
if (conf->type == IEEE80211_IF_TYPE_MNTR)
return 0;
- rt2500usb_config_bssid(rt2x00usb, conf->bssid);
+ if (conf->bssid)
+ rt2500usb_config_bssid(rt2x00usb, conf->bssid);
return 0;
}
--- dscape.orig/drivers/net/wireless/d80211/rt2x00/rt61pci.c
+++ dscape/drivers/net/wireless/d80211/rt2x00/rt61pci.c
@@ -2434,7 +2434,8 @@ rt61pci_config_interface(struct net_devi
if (conf->type == IEEE80211_IF_TYPE_MNTR)
return 0;
- rt61pci_config_bssid(rt2x00pci, conf->bssid);
+ if (conf->bssid)
+ rt61pci_config_bssid(rt2x00pci, conf->bssid);
return 0;
}
--- dscape.orig/drivers/net/wireless/d80211/rt2x00/rt73usb.c
+++ dscape/drivers/net/wireless/d80211/rt2x00/rt73usb.c
@@ -1935,7 +1935,8 @@ rt73usb_config_interface(struct net_devi
if (conf->type == IEEE80211_IF_TYPE_MNTR)
return 0;
- rt73usb_config_bssid(rt2x00usb, conf->bssid);
+ if (conf->bssid)
+ rt73usb_config_bssid(rt2x00usb, conf->bssid);
return 0;
}
--
Jiri Benc
SUSE Labs
^ permalink raw reply
* [NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
From: Patrick McHardy @ 2006-05-11 14:56 UTC (permalink / raw)
To: David S. Miller; +Cc: Linux Netdev List
[-- Attachment #1: Type: text/plain, Size: 0 bytes --]
[-- Attachment #2: x --]
[-- Type: text/plain, Size: 1098 bytes --]
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
When deleting the last child the level of a class should drop to zero.
Noticed by Andreas Mueller <andreas@stapelspeicher.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
---
commit c75053e281212b5ed3990a0aaced865db7e456d2
tree be2c674d4545ea41200fc5c57d53a03cb0672a93
parent 0e44dc383787b472a7f13564c6bd8a44cc07d408
author Patrick McHardy <kaber@trash.net> Thu, 11 May 2006 10:29:30 +0200
committer Patrick McHardy <kaber@trash.net> Thu, 11 May 2006 10:29:30 +0200
net/sched/sch_hfsc.c | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/net/sched/sch_hfsc.c b/net/sched/sch_hfsc.c
index 91132f6..f1c7bd2 100644
--- a/net/sched/sch_hfsc.c
+++ b/net/sched/sch_hfsc.c
@@ -974,10 +974,10 @@ hfsc_adjust_levels(struct hfsc_class *cl
do {
level = 0;
list_for_each_entry(p, &cl->children, siblings) {
- if (p->level > level)
- level = p->level;
+ if (p->level >= level)
+ level = p->level + 1;
}
- cl->level = level + 1;
+ cl->level = level;
} while ((cl = cl->cl_parent) != NULL);
}
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox