RE: Two network cards - routing and iptables

RE: Two network cards - routing and iptables

[Harrison, Bruce (CXO)]

Hello Clemens,

    For issue 1, perhaps you are blocking ICMP traffic on eth1?
    For issue 2, ip_forward needs to be set to a 1 (not part of
iptables).

Take Care!


Bruce...


-----Original Message-----
From: netfilter-bounces@lists.netfilter.org
[mailto:netfilter-bounces@lists.netfilter.org] On Behalf Of Clemens
Eisserer
Sent: Friday, August 26, 2005 8:56 AM
To: netfilter@lists.netfilter.org
Subject: Two network cards - routing and iptables

Hi there,

I've just discovered the power of iptables and it just works well in
my selfbuilt isdn router. However now I also want to route between two
subnets and it just does not work.

I've two network cards in the pc:
eth0 - 192.168.0.1
eth1 - 192.168.1.2

when I try to ping another computer connected to 192.168.0.0/24
everything works fine, however I cannot ping my access-point in
192.168.1.0/24 (which works from a stand-alone computer withought any
problems).

This are my routes:
LKLET021.highwa *               255.255.255.255 UH    0      0        0
ippp0
192.168.1.0     *               255.255.255.0   U     0      0        0
eth1
192.168.0.0     *               255.255.255.0   U     0      0        0
eth0
default         LKLET021.highwa          UG    0      0        0 ippp0
m

Furthermore it would be great if I could use this computer as a
gateway for all computers in 192.168.0.0/24 and 192.168.1.0/24 so that
each computer in this net could reach each other. I tried to configure
iptables a bit, but withought any success :-(

It would be great if anybody could help me, I know those are
newbie-questions, sorry.

Thank you in advance, lg Clemens

Re: Two network cards - routing and iptables

[Clemens Eisserer]

Hello again and thanks a lot for answering me,

>    For issue 1, perhaps you are blocking ICMP traffic on eth1?
No, I do not block anything as far as I know regarding ICMP.

This configuration I use for iptables:
echo 1 >/proc/sys/net/ipv4/ip_forward
iptables -t nat -A POSTROUTING -s 192.168.0.0/24 -j MASQUERADE
iptables -t filter -A INPUT -s 192.168.0.0/24 -j ACCEPT
iptables -t filter -A INPUT -s 192.168.1.0/24 -j ACCEPT
iptables -t filter -A INPUT -p tcp --dport \! 8901 -j DROP

btw. do you know why I cannot connect to the internet from localhost
if I set the last line?
I tried to set -s !127.0.0.1 but this also seems to not work :-(

>    For issue 2, ip_forward needs to be set to a 1 (not part of
> iptables).
> 
> Take Care!
Is this really anything I need to do since I already set it to 1

Hope I am not nerving,

thank you in advance, lg Clemens

Re: Two network cards - routing and iptables

[Clemens Eisserer]

Strange thing ... the access point (Belkin) was not compatible with
the first card in the server (RTL8139D) but with the second (RTL8139D)
;-)
Strange thing, however after all it took  me 2 days since I always
thought its my fault.

Can't believe how easily Linux can be used as Router+Firewall.

Thanks for all the patience and help, lg Clemens

Two network cards - routing and iptables

[Clemens Eisserer]

Hi there,

I've just discovered the power of iptables and it just works well in
my selfbuilt isdn router. However now I also want to route between two
subnets and it just does not work.

I've two network cards in the pc:
eth0 - 192.168.0.1
eth1 - 192.168.1.2

when I try to ping another computer connected to 192.168.0.0/24
everything works fine, however I cannot ping my access-point in
192.168.1.0/24 (which works from a stand-alone computer withought any
problems).

This are my routes:
LKLET021.highwa *               255.255.255.255 UH    0      0        0 ippp0
192.168.1.0     *               255.255.255.0   U     0      0        0 eth1
192.168.0.0     *               255.255.255.0   U     0      0        0 eth0
default         LKLET021.highwa          UG    0      0        0 ippp0
m

Furthermore it would be great if I could use this computer as a
gateway for all computers in 192.168.0.0/24 and 192.168.1.0/24 so that
each computer in this net could reach each other. I tried to configure
iptables a bit, but withought any success :-(

It would be great if anybody could help me, I know those are
newbie-questions, sorry.

Thank you in advance, lg Clemens