FORWARD not working

FORWARD not working

[Tim]

[-- Attachment #1: Type: text/plain, Size: 585 bytes --]

ppl,

I rebuilt my box and can't seem to FORWARD anything. The same rules that were working with the old box into the new box and its not working. Did I miss anything.

Cannot traverse the chains...I ran the command lsmod to check to make sure the modules where loading correctly and did notice something that was not there in my old box. ppp_syntty, ppp_async, ppp_generic and slhc which states it is a generic ppp along with jbd which I never noticed before.

I anyone can point me to any reason or documentation why this is so, I would gratefully appreciate it.

Thanks
Tim

[-- Attachment #2: Type: text/html, Size: 1321 bytes --]

Re: FORWARD not working

[Arnt Karlsen]

On Sat, 15 Feb 2003 19:50:17 -0500, 
"Tim" <twr@bellsouth.net> wrote in message 
<000801c2d555$61c7dda0$0a0110ac@nebuchadnezza>:

> ppl,
> 
> I rebuilt my box and can't seem to FORWARD anything. The same rules
> that were working with the old box into the new box and its not
> working. Did I miss anything.

..compare 'cat /proc/sys/net/ipv4/ip_forward'...

-- 
..med vennlig hilsen = with Kind Regards from Arnt... ;-)
...with a number of polar bear hunters in his ancestry...
  Scenarios always come in sets of three: 
  best case, worst case, and just in case.

Re: FORWARD not working

[Joel Newkirk]

On Saturday 15 February 2003 07:50 pm, Tim wrote:
> ppl,
>
> I rebuilt my box and can't seem to FORWARD anything. The same rules
> that were working with the old box into the new box and its not
> working. Did I miss anything.
>
> Cannot traverse the chains...I ran the command lsmod to check to make
> sure the modules where loading correctly and did notice something that
> was not there in my old box. ppp_syntty, ppp_async, ppp_generic and
> slhc which states it is a generic ppp along with jbd which I never
> noticed before.
>
> I anyone can point me to any reason or documentation why this is so, I
> would gratefully appreciate it.
>
> Thanks
> Tim

1- Try "cat /proc/sys/net/ipv4/ip_forward" and see what it says.  If it's 
a '0' (zero), then you need to "echo 1 >/proc/sys/net/ipv4/ip_forward" 
to enable forwarding.

2- Ensure that the interfaces are the same as on the old box, IE if eth0 
was internal network on the old box, then double-check that it's the 
same on the new box.  If not, you can either change your rules to 
reflect the difference, or change what cable is plugged into which NIC.

3- Check "/sbin/iptables -v -n -L" and "/sbin/iptables -v -n -L nat" and 
see if ANY rules, or chain policies (especially nat-PREROUTING, earliest 
hit of those listed) reports any packets.

4- If the first two aren't the problem, then:  If the third shows NO 
traffic at all, your problem isn't iptables.  If the third shows 
traffic, try to see what rules and what chains the traffic is appearing 
in, and make sense of it.  Try inserting "-j LOG" rules as first in each 
chain for a minute or two and check the logs to track packet traversals.

5- Also confirm whether the firewall box itself is able to communicate in 
each direction.  At the minimum, you should ping a machine out each 
interface.   Set INPUT and OUTPUT chains to ACCEPT policy and no rules 
if necessary, but try to narrow down where the problem really exists.

6- Check "ip route" and "ifconfig" and ensure your interfaces are all up, 
and you have appropriate routes.  Routes should look something like 
this: (eth0 is the interface ppp0 subsumes, eth1 is LAN)

10.10.21.1 dev ppp0  proto kernel  scope link  src 141.150.238.220 
192.168.0.0/16 dev eth1  scope link 
127.0.0.0/8 dev lo  scope link 
default via 10.10.21.1 dev ppp0 

6- If all this turns up no answer, then post with a bit more detail, such 
as what distribution you were/are running, what version, what kernel, 
and what version of iptables you were/are running.  

j

Re: FORWARD not working

[...]

[-- Attachment #1: Type: text/plain, Size: 835 bytes --]

did you tried to set:

echo "1" > /proc/sys/net/ipv4/ip_forward

...
  ----- Original Message ----- 
  From: Tim 
  To: iptables-list 
  Sent: Saturday, February 15, 2003 9:50 PM
  Subject: FORWARD not working


  ppl,
   
  I rebuilt my box and can't seem to FORWARD anything. The same rules that were working with the old box into the new box and its not working. Did I miss anything.
   
  Cannot traverse the chains...I ran the command lsmod to check to make sure the modules where loading correctly and did notice something that was not there in my old box. ppp_syntty, ppp_async, ppp_generic and slhc which states it is a generic ppp along with jbd which I never noticed before.
   
  I anyone can point me to any reason or documentation why this is so, I would gratefully appreciate it.
   
  Thanks
  Tim

[-- Attachment #2: Type: text/html, Size: 2315 bytes --]